Screen made of wood with your own hands. Screen for the room with your own hands. DIY stained glass screen with glass

Sometimes a situation arises when a room needs to be artificially divided, for example, to fence off the work area from the bed or create a light barrier for a baby cradle. In this case, it is not necessary to make repairs and erect partitions, it is not even necessary to buy a closet or curtains, you can solve the issue with the help of such an undeservedly forgotten piece of furniture as a screen for the house. We offer you a step-by-step guide on how to make a screen with your own hands.

To make a screen, we need the following materials:

• wooden beam (4 × 4 cm),
• fabric - linen (3 × 1.4 cm),
• strong threads,
• acrylic paint beige colour,
• brushes of medium width,
• grinder or sandpaper
• putty for wooden surfaces,
• hinges for the opening system, counting two pieces per section,
• screwdriver, hammer,
• roulette,
• saw,
• screws, decorative nails,
• ruler, pencil, scissors.

Scheme with the dimensions of the design of the screen for the house.

We make the marking of the timber (4x4) with the calculation of six bars of one hundred and eighty and six bars of fifty centimeters.

We process wooden blanks sandpaper or grinder, to smoothness.

We begin the preliminary constructive layout of the screen for the house. We lay out the long bars on top of each other in pairs, at a distance of 50 cm. Short bars are jumpers, we place a pair, between the long bars, step back 15 cm from both edges. The third short bar is placed in the middle. We fasten with long screws all the bars from the end, on both sides. We fasten all three sashes in this way.

How to make a screen with your own hands smoother? It is necessary to carry out preliminary work to close all the irregularities and cracks - with putty, after drying, we sand the puttied places with fine sandpaper.

After completing the surface preparation of the future screen for the house, paint the tree with the paint you like.

The manufacture of the screen, which carries its part, is almost completed. Let's move on to cutting the fabric. On the fabric we measure six large rectangles with dimensions of 152x50 and twelve small rectangles of 30x25 centimeters.

For allowance, we leave at least one and a half centimeters around the perimeter of each workpiece.

Our screen for the house will perform not only the function of zoning, but will also be a convenient place to store newspapers, papers and other small things. To do this, on each of the three large canvases, we have four pockets in two rows. We do a preliminary fitting, choose the height. Next, we fold the fabric under the pocket along the hemming line, sweep it and attach it on the machine.

We connect the individual sashes with the help of loops.

The manufacture of the screen proceeds to its final stage - with the help of decorative carnations and a hammer, we nail the fabric with folded edges to the wings. From the inside, the canvases are attached in the same way, in this case we use canvases without pockets.

Congratulations! How to make a screen with your own hands - you know for sure that it's easy!

The traditional screen for dividing the space in the room is created from a wooden frame and fabric stretched between the slats. But materials and methods on how to make a screen-partition for a room with your own hands, thanks to modern technologies became much more.

Lightweight partition screens made using a wooden frame, paper or fabric canvas are suitable for visual zoning of a room. When using a solid screen, you can achieve functionality: install small shelves for accessories, if necessary, hang clothes and bags on the top of the structure.

In order for the partition screen to serve for a long time and not cause trouble, at the project planning stage, you need to take care of the availability of all materials. Required Tools for a small partition screen of 3 sections with paper and fabric filler:

You can do without the help of a drill, but if you have a tool, it is easy for them to screw the screws into the partition screen.

Instead of wood, bamboo rods, plastic profiles or aluminum are used for, but working with them is somewhat more difficult than making a partition screen from bars.

The fabric-paper web will be replaced by drywall sheets, which can be attached to the profile with small nails and self-tapping screws.

How to make a partition screen for a room with your own hands

Making a do-it-yourself partition screen using fabric is a simple process even for a person who has recently started creating home-made things for the home.

Moreover, light baffle for changing clothes is a great opportunity to practice making simple furniture for the home.

When preparing materials for a partition screen, check the dimensions of the planned frame, fabrics and other components to fill the openings, take 3-4 cm more in width and height. It is best to cut fabrics from a common roll with fitting on the frame made.

Before designing your own screen plan, explore a few ideas for making functional and durable screens.

Frame manufacturing

After drawing up a sketch of the partition screen and calculating the dimensions, they begin to manufacture the frame:

It is possible to make a screen-partition with legs, then the horizontal bars from below are fixed 7-10 above from the vertical wooden lath. In this way, 2 more sections of the partition screen are made if the structure consists of 3 parts.

Screen cloth

While the frame for the screen dries, prepare the main canvas to fill the structure:

Instead of a stapler, rubber-based glue or decorative loops are used to attach the canvas to the partition.

Remember that when connecting the fabric with different compartments of the screen, it must be well stretched.

For these purposes, special construction pins are also suitable.

Screen assembly

The final stage is the connection of the partition screen sections. Loops are preliminarily prepared, corresponding to the size of the frames and the expected severity of the screen-partition. Start assembly:

After 1-2 days, the screen can be used. In addition to the fabric, if desired, pockets are attached in which they are stored various little things. The main thing is that the partition can withstand the weight.

Alternative option from cardboard tubes

In the manufacture of partition screens, any improvised means are used: plastic pipes, acrylic panels, bamboo branches, and even CDs or records.

The partition screen made of cardboard tubes looks original, which is very similar to bamboo, only more even, but just as environmentally friendly.

Take 16 to 20 pipes, decorative string and paint to cover the frame. Of the tools you will need a tape measure, scissors and a drill.

It’s easy to make a partition screen out of cardboard with your own hands:

The final stage is the processing of the partition screen with a coloring material. You can choose a light brown shade, and additionally draw “eyes”, like trees, imitating bamboo.

Video how to make a partition screen

To understand how to make a screen, watch a video from a professional. Detailed recommendations and some secrets will help create the perfect partition decorative type for an apartment!

A beautiful do-it-yourself partition screen is a pride for the owner and an excellent element of the interior, zoning the space and performing other functions.

The use of decorative partitions to delimit space and decorate the interior has been known since ancient times. Lightweight, compact and mobile screens were used many centuries ago in China, Greece, Egypt, the Roman Empire. They were made of simple and lightweight materials, they could be of different sizes and shapes. Wealthy owners decorated partitions with rare fabrics, inlays, precious metals and stones. We invite you to learn how to create beautiful, original screens with your own hands.

What are the screens

When choosing a screen model, not only the stylistic orientation is important. It is necessary to take into account the space in which the product will be located, its mobility and even functional purpose. Therefore, we turn to the theory and consider what types of screens are.

1. Folding sliding. They consist of several interconnected frames, from 3 to 8 or more. If necessary, they can be folded in the form of an accordion and removed.
2. Single-screen screens consist of one wide sash. It can be a frame made of any material with stretched cloth or paper, a sheet of plywood, chipboard, plastic or glass fixed on a stand. It is desirable to provide such a screen with wheels so that you can roll it to the right place.
3. The screen-book consists of two wings of the same width (although asymmetry is allowed). Fold it in the form of a book and rearrange it where less space. Depending on the decoration, such a screen can be used for dressing up and even for holiday photo shoots.
4. Flexible screens. They are made from many long thin sections: pipes, plates, rails, connecting to each other. The peculiarity of this screen is that you can put it in a wave, a spiral, or even twist it into a roll and put it aside - it does not take up much space.
5. Blind screens can consist of a different number of wings, their distinguishing feature is complete opacity. This can be a solid board (plywood, chipboard, plastic, metal sheet, frosted glass), a dense fabric stretched over the frame, or cardboard inserted into the frame. Such screens are used not only for zoning rooms, but also as a partition for changing clothes.
6. Transparent screens. Most often, this is a transparent fabric stretched over a frame - organza, tulle and even starched gauze; very convenient to use mosquito net. Also popular metal models, made using the air forging technique, or wooden screens with openwork through carving. Such products are decorative in nature, they are often used for wedding and holiday photo shoots or to decorate rooms and gardens.

From what materials is it better to make a decorative partition for a room

Traditionally, screens were made of wood: a solid board or slats on which the fabric was stretched. Nowadays, a creative approach and the use of the most different materials. Let's consider them in more detail.

1. Tree. As before, it can be a board - smooth or with a pattern cut out on it, or a structure made of bars or battens. Plywood is in demand for creating screens due to its cheapness, lightness and ease of processing. In addition, designers offer great ideas on the use of obsolete items. For example, you can build a screen from old doors, having previously restored the panel, giving it a fresh look. screen from wooden elements can be placed both in the house and in the garden.
2. Metal. The most commonly used metal frames given form, which can be ordered from a familiar welder or at a specialized enterprise. Panels made of wood, glass, plastic are inserted into these frames, or fabric is stretched. A sheet of iron will look bulky and will not add coziness to the room, but an ornament forged from rods will greatly enliven the product. Often, metal pipes of small diameter (up to 5 cm) are used to create such a frame. This screen looks great in the garden or yard.
3. Plastic pipes are also used in the construction of frames and screen frames. They are much cheaper, and most importantly - lighter than metal ones. screen from plastic pipes it is easy to assemble and disassemble if necessary, and it is very easy to maintain: it is enough to brush off the dust from the surface in time. If necessary, you can hide under it on the street on a hot sunny day.
4. Plastic panels are a very easy-to-use material, often already ready to be used as a screen. It is enough to pick up several panels with the same pattern, connect them - and now you no longer need to think about fabric drapery fasteners. And you can also insert the panel into the frame from wooden slats or metal. Such screens are not afraid of the sun and rain, they can decorate a garden plot.
5. Cardboard - cheap material, which can quickly turn into an original, creative screen. Working with cardboard is very simple: just cut out the details according to the scheme and fasten them into a single canvas. Often such screens are placed not only straight or at an angle, but also in waves. True, they are completely unsuitable for the street: they deteriorate from moisture, wind and sun.
6. Branches: bamboo, wicker, reed. Screens from these materials are very popular due to their lightness, mobility and visual simplicity. The fashion for them never goes away, they are combined with many styles in the interior: classic, tropical, eco-style, empire. True, the manufacture of such a screen requires the skills of weaving from a vine. But the finished product will look appropriate in the garden and will not deteriorate from weather conditions if the material is processed correctly.
7. CDs, vinyl records. They can be connected to each other with threads or staples, you get a stylish openwork fabric. It is hung anywhere in the room in a straight line, in the form of a wave or a semicircle. More often, screens made of plates are used in the house, but on the street such a decorative element looks original.

Unusual handmade screens - gallery

Decorative cords stretched vertically over the frame - a simple and very effective partition screen Vinyl records, linked to each other in a canvas - a great decoration for a music lover's room Reed or bamboo is an excellent material for a flexible screen
The screen can be made from ready-made door leaves, which are sold in hardware stores. A simple screen from smooth boards can do it yourself Do not rush to throw away old doors - they will make a great decor element for your home Wooden slats and a fabric stretched over them with an interesting pattern - bright accent in any room Cardboard butterflies assembled into a three-dimensional canvas will decorate your room From cardboard rectangles, you can build an original high-tech screen

Necessary improvised materials and assembly schemes

There are many ideas for making screens. We tried to pick for you those that are not very difficult for beginners. The materials and tools used in the master classes are quite affordable.

Classic-shaped screen made of wooden beams and fabric

The traditional version of the screen provides for a fabric stretched over a wooden frame. The product can be made in the form of a book, dressing table or accordion, the shape depends on the number of frames. And the pattern on the fabric and its colors determine which room your screen is suitable for.

Required tools:

• drill;
• screwdriver;
• construction stapler;
• 12 door hinges;
• hacksaw;
• sandpaper;
• 96 screws.

In addition, you will need materials:

• wooden bars;
• varnish and paint;
• the cloth;
• universal glue;
• decorative elements (ribbons, beads, applications, and so on).

For a full-fledged screen, you need to take 24 bars 6 cm wide and 2 cm thick, of which 12 pcs. 170 cm long and 12 pcs. 60 cm long.

1. The basis of the screen is a frame, it is not difficult to make it. First of all, you need markup. Take the bar, measure 6 cm from its edge with a ruler and draw a line with a pencil. Repeat on each plank.
2. Now, with a hacksaw, make incisions according to the markings. Their depth should reach half the width of the bar.
3. Make cuts from the edges of the plank: put a chisel to the beam and, hitting it with a hammer, remove the layers of wood to the notch.
4. Apply all-purpose glue to the inside of the notch. Assemble the planks into a frame and press firmly.
5. Wait for the glue to dry completely, then sand the surfaces with sandpaper, especially at the joints. Finish the frames with wood varnish.
6. Door hinges are needed for fastening (you can replace them metal corners). Fasten them to the frames with screws using a screwdriver.
7. The base for the screen is ready, now you need to decorate it with fabric. It can be of any color and texture, when choosing, be guided by the main colors of the interior and your preferences. First of all, make a pattern according to the size of the frames, in which take into account the hem. That is, on each side of the frame you need to add 5 cm. You can use fabric of different colors or even the remaining large pieces of different matter by stitching them on a sewing machine.
8. Use a construction stapler to attach the fabric to the frames. First of all, fix the upper part, then, having stretched the fabric well, fix it on the bottom bar of the frame. The tension must be very good so that subsequently the fabric does not begin to sag. Fasten the sides last.
9. When you finish fitting all the frames, proceed to assemble the screen on the door hinges. You will need 2 loops per 1 connection, so that later it is convenient to fold the product.

We make a screen from wooden slats and fabric - video

Portable screen made of cardboard tubes: creative, unusual, eco-friendly

Eco-design interior has not gone out of fashion for several years. Its feature is the use natural materials and ease of manufacture. From the usual improvised things that are often sent to the trash as unnecessary (packaging, wrapping materials), you can create real masterpieces with maximum imagination and minimum effort.

We suggest you make a light screen from the simplest material - cardboard tubes for winding linoleum or fabrics. In specialized stores, they are thrown away like waste, so you can buy them literally for a penny. And if you're lucky, you can even get it for free.

Such a screen is very stable due to its wavy shape and its own weight. To make you will need:

• 16–20 cardboard tubes for winding fabric;
• a skein of strong decorative rope;
• roulette;
• scissors;
• pencil;
• drill
• if desired - paint a color suitable for the interior.

If you are using linoleum pipes, take 8-10 of them. Since their width is more than 3 meters, you need to cut each in half.

1. Cut the pipes to the height you need. You can alternate different heights and widths, so the screen will look more fun. Lay all the pipes in a row, aligning along one edge: it will become the bottom of the structure.
2. Measure 20 cm from the bottom edge and make a mark on each pipe at this level (point A). Measure a length of 1 m up, mark again (point B). Strictly in the center of the segment, mark point C. Repeat the action with all pipes.
3. Using a drill at low speed, drill holes through at the marked points.
4. First, at points A, then B and C, thread a decorative rope through the holes.
5. Push the pipes tightly and tie strong rope knots on the sides of the screen.

That's all, the screen is ready. Outwardly, it resembles bamboo or reed.

If desired, such a screen can be moved anywhere in the apartment to block the bed, workplace or just to demarcate the space.

Modular cardboard partition

Even such a simple and unpresentable-looking material as carton boxes, will serve us well. And if there is an opportunity to get sheets of cardboard - generally wonderful! In order to make a cardboard screen yourself, prepare the following materials:

• cardboard sheets 4 mm and 7 mm wide;
• ruler;
• pencil;
• scissors or utility knife.

To create modules, use the diagrams below.

1. You can redraw these diagrams by eye or print on a printer, maintaining proportions. Each side is measured in centimeters. You will get 5 parts, in the diagrams they are marked with the letters A, B, C, D, E.
2. Cut out the diagrams. Attach each detail to a sheet of cardboard and carefully circle with a pencil, taking into account all the slots. To test, put two pieces of cardboard together to check the width of the slot.
3. From thinner cardboard, cut out parts A-D, from what is thicker - parts E: they will serve as the legs of the screen. You end up with 16 A pieces, 80 B pieces, 70 C pieces, 64 D pieces, and 5 E pieces.
4. When you cut out all the details, start collecting individual modules. Parts C and D will become connectors for A and B, the larger ones.
5. Use C connectors to fasten the screen modules.
6. Parts E, which serve as legs for support, fasten to the bottom of the screen.
7. The size of such a screen can be adjusted, making it higher or lower, forming a cascade or ladder.

A simple cardboard partition: an option for beginners

If the process of creating a screen from complex multi-part modules seems complicated to you, use the simpler option. You will need:

• sheets of cardboard;
• pencil;
• scissors.

You can take cardboard of the same color, or "play" with the gradation of shades.

1. On thick cardboard, redraw the outline of the part from the picture. Required dimensions you can choose for yourself, depending on your own preferences or the parameters of the room where the screen will be located. You will need a lot of such details, but there should be a pair of them. Carefully cut with scissors, taking into account all the grooves.
2. Prepare the modules by connecting 2 parts perpendicular to each other into the central grooves.
3. Line up the finished modules, fixing them to the side grooves; build the second row in the same way, and so on. You will get a light and original screen of the required size and shape.

According to the same scheme, you can create a screen from cardboard butterflies. Cut out the details for the modules in the form of insects. Use different colours, so the screen will turn out brighter and complement any interior.

In the same way, connect 2 parts to each other, and then extend the modules to the size of the screen you need.

DIY cardboard changing screens - video

Mobile screen made of metal or plastic pipes

A partition screen made of metal pipes helps to zone the room or hide from sun rays on a hot summer day. And the peculiarity of this design is that it easily moves on wheels.

To make such a screen you will need:

• 3 metal pipes for the frame;
• 1 metal pipe to weight the base;
• 4 furniture wheels;
• 2 corners for connecting pipes in the upper part;
• a board that will serve as the base of the screen;
• 2 flanges fixing the pipes to the board;
• self-tapping screws and nuts-washers;
• screwdriver;
• brush and paints.

Metal pipes can be replaced with PVC pipes of the same length and thickness. But to make the foundation heavier, you still have to take iron pipe or other heavy load.

1. Draw markings on the board, indicating the places where the furniture wheels are attached.
2. Fix the wheels with self-tapping screws on the board using a screwdriver.
3. Now you need to fix the weighting agent on the underside of the base of the screen. Fasten the load with self-tapping screws using holders. This is necessary so that the screen does not fall during operation. Unfortunately, the higher such a design, the less stable it is, so weighting is indispensable.
4. Fasten the flanges from the top side of the base board, insert the pipes into them.
5. Connect two vertical pipes on top of one horizontal pipe, inserting their ends into the connecting elbows. When finished, paint the structure.
6. Now it's time to show your imagination. If you plan to use the screen solely as a partition, hang a thick fabric on the frame. Even an old curtain can serve as it; the main thing is that the size of the fabric matches the width of the frame, and the color and pattern match the main notes of the interior.

And also such a screen on wheels can be temporarily used as a mobile wardrobe. Put it in the bedroom and hang clothes on hangers.

Opaque sliding structure made of wood

If you need a thick screen that can even muffle sounds, then you need something more serious than a piece of fabric attached to the frame. Use wood.

A wooden structure will serve you not only as a partition. Thanks to the dense lining, you can attach family photos, children's drawings and crafts to the screen.

The case for the screen can serve as thin wide boards from any available wood. The easiest way is to use MDF panels.

You will need:

• 3 thin boards 45 cm wide and 180 cm long;
• 3 cuts of synthetic winterizer 50 X 200 cm;
• 3 pieces of dense fabric 50 X 200 cm;
• primer or sealant;
• construction pistol;
• acrylic paint;
• screwdriver;
• scissors;
• upholstery tape;
• hinges for doors;
• decorative building nails.

If you have the opportunity to find boards of greater width, use them. Just do not forget that the synthetic winterizer and fabric need to be adjusted in size.

1. First, prepare the boards or MDF panels. Cover one surface with a primer - this will be the back. Once the primer is dry, paint that side of the panel with acrylic paint.
2. From the padding polyester, cut a strip a little wider than the panel, taking into account the allowance. Lay the material on the board and fix it with a construction gun. Cut off the excess padding on the sides with scissors.
3. It's time for the fabric. The cut should be the same size as the synthetic winterizer. Attach the fabric to the panel, pull it well, break the edges and secure with a construction gun over the synthetic winterizer layer.
4. Attach the upholstery tape around the edges of the panel with glue. Additionally fix with decorative nails, driving them in at a distance of 5 cm from each other. Repeat these steps for all panels.
5. Now it's time to connect the structure. Lay two panels face down; check that the bottom edges are at the same level. At a distance of 10 cm from the bottom and top edge attach furniture hinges, attach them with a screwdriver. Fix the third panel in the same way.

If desired, you can additionally decorate the finished screen with a pattern of decorative nails, giving the surface volume and texture.

Screens for creating spectacular photos

If you are a professional photographer, then you probably know how important it is to have beautiful, spectacular screens for thematic photo shoots. Most often, such orders are made for a wedding, but other celebrations are also in demand. Therefore, a beginner in the photography business needs to consider every possibility just in case. We will help you create beautiful, light and airy screens for various photo shoots.

Painted screen for wedding photo shoots

A master class for making a wedding screen is based on the same principles by which similar products are made from wooden frame and fabrics. True, it will be a little more difficult: you will have to realize your skills in painting.

To make a screen for photo shoots, you will need:

• mosquito net;
• wooden bars;
• angle brackets;
• long self-tapping screws 5.7 cm;
• short self-tapping screws 1.27 cm;
• loops;
• scissors;
• acrylic paint (white);
• sequins;
• stapler;
• drill for tightening screws;
• protective coating on water based;
• tassel;
• white paint for wooden surfaces.

First you need to decide what size the screen will be. It depends on the size of the room in which photo shoots are held, the number of participants, additional decor items. Having determined the height and width of the future product, you can easily calculate the quantity the right materials. For example, you can use the dimensions presented in the previous options for making screens.

Manufacturing and assembly instructions.

1. Cut the bars according to the given sizes, assemble them into a frame. Connect the elements with self-tapping screws and angle brackets. To do this, it is easier to use a screwdriver or a drill with a screwdriver bit.
2. If you choose to paint the frame white, do so immediately after assembly. You can do without this, leaving the tree its natural color, but then it is advisable to open the surface with varnish.
3. Now you need to fix the mosquito net. Cut it into pieces according to the size of the frame, leaving a small allowance. Lay the mesh on the back of the future screen and attach with a construction stapler.
4. Cut off the excess mesh with scissors.
5. Using a brush, spread the water-based coating onto the mesh. This will help the paint stick better when you apply the drawing. Wait for the mesh to dry.
6. The time has come creative work: Apply a pattern. You can choose any floral and fantasy motifs. Apply acrylic paint in light strokes using the same brush as for protective coating. To create shadows, you can add a little gray or black paint.
7. To give the screen for photo shoots a festive brightness, coat some places on the surface with PVA glue and sprinkle with sparkles. Let the product dry well.
8. It remains only to connect door hinges all three frames are interconnected - and the screen for solemn photo shoots is ready!

Screen for creating a photo with fabric drapery

A simple master class from the famous Moscow decorator Elena Teplitskaya will help you make a cute, funny and original screen that will surely come in handy for photo shoots.

Materials and tools you will need:

• frame made of metal rods;
• cuts of well-draped fabric, for example, organza;
• threads and needles;
• decorative cord;
• textile markers.

As a screen decoration, you can take thread balls, decorative braid, ribbon or bows - whatever your imagination tells you. In addition, the fabric can be either one color or different colors on each screen frame.

1. Cut the fabric to fit the screen. The width should match, and the length of the cut should be 20 cm more than the height, in order to subsequently make a hem. Organza or other light translucent fabric can be pre-treated with a solution with the addition of starch - this will make it stiff and pliable. Form folds by squeezing the cuts vertically so that the fabric looks like crepe paper.
2. Spread the fabric over the top of the frame, securing it with pins. Do not stretch it in a horizontal direction: it should lie in folds. Now, with neat stitches, sew the places chipped with pins.
3. With a special fabric marker, apply some simple ornament to the drapery. This stage is a great way to realize your artistic talent.
4. The applied pattern must be dried with a hairdryer. If you are working with a special embossing dryer, be careful not to bring the tool too close to the fabric: it may catch fire. Turn on a regular hair dryer for a maximum of second speed.
5. Paint the visible metal parts of the frame with a marker in the color of the fabric and the ornament on it. Decorate the top of the screen: string thread balls, bows or other elements of your choice on a decorative cord, and fasten to the fabric with a stapler or sew.

DIY room partition - video

Decorative partitions were first made in China. Today, screens are used to decorate the interior and its zoning. How to make your own screen with your own hands?

How to make a screen with your own hands - materials

To make a wooden frame screen, you will need:

• 12 pine planks 170 cm (6 cm wide, 2 cm thick);
• 12 pine planks 60 cm (6 cm wide, 2 cm thick);
• pencil;
• square;
• wood glue;
• wide brush;
• light varnish for wood;
• hacksaw;
• thin chisel;
• hammer;
• joiner's vice (4 pcs.);
• screwdriver;
• sandpaper;
• 12 steel corners;
• 96 wood screws with a diameter of 3 mm and a length of 1.5 cm.

How to make a screen with your own hands - manufacturing

• Step back 6 cm from the end of each pine plank. Draw a straight line with a simple pencil along the wide part of the planks.
• To the middle of the width of the planks, we make cuts with a hacksaw along the marks marked with a pencil.
• From the end of the planks, using a hammer and a chisel, we begin to remove the tree in layers, forming cuts.
• Apply glue to the notches and connect the short planks to the long ones into a rectangle. Fix these points of the frame with a vise. Now you need to wait until the glue dries.
• After complete drying, sand the frames with sandpaper and coat with a light wood varnish.
• To prevent the frames from falling apart in the future, attach the corners with screws at the corners.
• Thus, you got 6 separate frames and it's time to start decorating them and final assembly screens.

How to make a screen with your own hands - screen decor

The easiest way to decorate a screen is to use fabric. Choose its density and color according to your taste (from organza to thick cotton or linen). To fix the fabric on the frame, you need to use a furniture stapler. If there is no special stapler, then use hot glue. Some designers wrap fabric around frames and fix it with needles. This option is not suitable for those who have small children in the house.

How to make a screen with your own hands - final assembly

The final assembly of the screen involves connecting the frames to each other with hinges. Make no mistake with the mounting side. Your screen should fold like an accordion.

How to make a screen with your own hands - ideas

In fact, screens can be decorated with the most unpredictable materials:

• multi-colored glass bottles;
• branches;
• paper, cardboard and newspapers;
• threads and ropes;
• garlands;
• ivy;
• organic glass.

To make your screen easy to move, attach special wheels at the bottom.

A handmade screen will be a real decoration in your home. It is not necessary to build brick walls to divide the space, use mobile partitions for this purpose.

Such an additional and interesting decor element as a do-it-yourself screen made from improvised materials can fit perfectly into the interior. Thanks to the screens different design you can allocate space at your own discretion, hide personal belongings from strangers.

As we have already mentioned, it is not at all necessary to immediately go to the store in order to purchase a finished product - the manufacture of such an interior element is not considered difficult, and thanks to the variety of design ideas, you can independently create an exclusive screen that fits perfectly into the room. Below we will consider various options partition walls.

Advantages and disadvantages of using screens

If space is limited in an apartment or a particular room, it becomes necessary to properly distribute it. It is not always possible to make an additional wall in the room, because you will have to make changes to the layout of the apartment, which will entail additional expenses. That is why many people choose convenient screens that are quite easy to install and, if necessary, dismantle.

The main advantages of using screens:

1. Mobility. Some types of structures can be transported from place to place without any problems.
2. Low cost for self-manufacturing.
3. The ability to increase the functionality of the product, with the help of additional shelves or hooks.
4. Decorating the room, because the screen can be decorated in any way at will.
5. The ability to design a structure according to the exact dimensions of your room.

Among the shortcomings of the screens, the following can be distinguished:

• poor sound insulation;
• fencing insecurity.

The disadvantages of such structures are much less. Also, they are not for everyone.

What are the screens?

There are several varieties of products such as screens, so before choosing one or another model, you should decide on its purpose.

Table 1. Varieties of products

View, illustration	A comment
	They are a reliable frame, the parts of which are fixed to each other with the help of furniture hinges. Most often there are three-leaf or four-leaf screens, but this depends on the dimensions of the room. The average height of the finished product is about 180 centimeters.
	The design is a type of one-piece sash, which is why it is considered less mobile compared to other types. Such screens most often delimit office space, kitchen and living room. In addition, such partitions are relevant in various cafes in order to separate tables.
	The product consists of many vertical rails, which are interconnected by elastic inserts. The peculiarity of partitions of this type is that they can be given any shape. Therefore, they are often used in unusual designer interiors. The main advantage of this kind of screens is the ease of storage, because they are quite easy to fold.
	This is a type of folding screen. The design feature is that it consists of two parts that are the same size and folded like a book. They are often used to allocate space for a locker room.
	They are a product of any configuration, through which you can see everything that is on the other side. Most often, fabric is pulled over the main part of the structure, different kinds grids. Screens are installed only as decorative element, they are often used by photo studios when decorating a room.
	Such screens have different appearance and the number of valves, their main feature is the lack of transparency. Therefore, it is these designs that are used in cases where it is required to hide some part of the room from prying eyes.

Materials for the manufacture of screens: how to choose?

At all times, screens were made of wood. various breeds, and then a textile part was stretched onto a wooden frame. Now, to create structures, all kinds of, and sometimes even unusual, materials are used.

Table 2. Types of materials used for the manufacture of partitions

Material, illustration	A comment
	In the manufacture of products, both polished wood and joints of various laths and boards are used. Often, plywood is used for such purposes, because such material has a budget cost and is easy to process. In addition, any old, unnecessary items can be used to make a screen (it can even be wooden doors or window frames). You can install such a partition both indoors and in the yard of your house.
	Such material is used to make the frame of the screen, after which the product can be sheathed with wood, fabric and even paper. You can order such a frame to a master who has specialized equipment. It is worth noting that one should not make a solid metal screen, because it will not have a very attractive appearance and a large mass. It is recommended to use thin metal rods for such purposes. The metal screen will fit perfectly into the design winter garden with various plants.
	PVC pipes are often used for the manufacture of various frame structures, including partitions. Their main positive quality compared to other products is their light weight, so this screen can be carried around the room without any problems. The designs are easy to clean, just wipe them with a damp cloth to remove dust. Products are often used outdoors to hide from the active rays of the sun in hot weather.
	It is a popular material used to make various screens. Ready-made decorative panels, which are quite simply fixed on the frame. The advantage of the structures is that they do not deform when exposed to moisture, high temperature, so they are often installed in showers.
	The cheapest and most accessible material for the majority of the population, which is used in the manufacture of screens. The peculiarity is that any decorative design can be made from it - you can quickly cut out parts of any shape from cardboard using a clerical knife, and then fix them together. The disadvantage of cardboard screens is only poor resistance to negative changes environment, so they are only suitable for an apartment, and even there they require regular updating.
	This material is often used to make various decorative screens, because such structures look aesthetically pleasing and unusual, and also have a small mass, are mobile, making them quite easy to carry. It is worth noting that correct handling material will allow you to install a screen even on the street.
	Most unusual way production of partitions from the options presented above. You can fix the plates with the help of various decorative threads, which will make a kind of curtain. Such screens are used only for decorative purposes, they can be placed in an apartment, office, shop or cafe.

Making screens with your own hands from improvised materials

There are a huge number of schemes by which you can assemble the partition yourself. In addition, the materials used in the course of the work are considered accessible. Below we will present some simple but original options.

A simple version of a screen made of wood and fabric

This is a classic way of making partitions, and the material is stretched over a finished wood structure upon completion of its assembly. The product can have a different configuration, including a folding shape, in the form of an accordion. It is important to choose the fabric of the desired texture and a certain shade, depending on where you plan to install the partition.

During the manufacturing process, you will need the following:

• bars (12 pieces 2 centimeters wide and 170 centimeters long, 12 pieces 2 centimeters wide and 60 centimeters long);
• textile;
• stain and varnish;
• water-based coating agent;
• glue;
• elements for decoration;
• screwdriver;
• drill;
• door hinges;
• stapler;
• screws;
• sandpaper;
• saw.

Step-by-step instruction

Step one: it is necessary to put markings on the bars in order to manufacture the frame. Therefore, it is necessary to measure 60 millimeters from the beginning of the bar using a measuring tape and simple pencil and then draw a line. The same actions are repeated on other bars.

Step two: you will need to make cuts according to representative markings - for this you need to leave recesses up to half of each bar with a hand saw.

Step three: along the edges of each plank, it is necessary to remove the wood with a hammer and a chisel, to the base of the cut.

Step four: a layer of wood glue should be applied to the inside of the log house, and then the bars should be connected into a solid frame.

Step five: when the glue is completely set, you will need to carefully treat the surface with sandpaper. After that, it will be possible to apply the first layer of varnish to the frame structure.

Step six: as connections, it is necessary to fix furniture hinges or corners on the structure. They are fixed with a screwdriver and screws.

Step seven: when the frame of the screen is completely ready, it is necessary to proceed to the stage of creating its fabric part. You can choose any textile material, in this case it is important to consider the location of the product. Cut out the fabric should be based on the size of the frame itself. Be sure to leave a few centimeters for the hem. In the absence of a single piece of fabric, you can use a combination of several different types, the main thing is that they are combined in structure, due to which finished construction will look aesthetically pleasing.

Step eight: in order to fix the fabric on the slats, you will need a special stapler. It is necessary to fix the material from above, moving towards the bottom of the structure. It should be borne in mind that the textile must have a good degree of tension, otherwise it will quickly sag in the future.

Step nine: after fixing the fabric on all frames, it is necessary to fix the parts of the screen with furniture hinges. It is advisable to use two loops for each connection, so it will be much more convenient to fold and store the screen.

Mobile screen made of cardboard tubes

Per last years the manufacture of various structures for the home from environmentally friendly and available materials- these include cardboard pipes. Film, linoleum, textiles are wound on them for the purpose of easy storage, so you can buy them for a symbolic price at a hardware or textile store, because such pipes are waste and are sent for recycling. Sometimes they are given away free of charge, subject to self-delivery, which can significantly save the budget.

Despite the ease of manufacture, such a product will have good stability. In the process of work you will need:

• cardboard pipes of the desired length - at least 18 pieces;
• tight cord for connection;
• measuring tape;
• scissors;
• simple pencil;
• drill;
• paint (if you plan to paint the screen).

Step-by-step instruction

Step one: All pipes must be aligned desired height. So, if linoleum coils were taken as the material, then they are usually sawn into two parts, because the average height is about two to three meters. Some craftsmen prefer to cut pipes of different heights, so that the design takes on an unusual look. Next, they need to be decomposed into flat surface, aligning to the bottom.

Step two: from the bottom of the pipe it is necessary to make a mark at a distance of 20 centimeters (lower point). Then you will need to leave the designation at a distance of 100 centimeters up (upper point). In the middle of the segment, you should again put a mark (center point). All other pipes are marked in this way.

Step three: in places where marks were made, you will need to make holes with a drill.

Step four: starting from the lower points, a decorative cord should be threaded into the holes.

Step five: then it is necessary to tighten the pipes together so that the structure is tight. The finished screen can be installed in any room. It has an original appearance that resembles bamboo.

Lightweight cardboard screen: an option for beginners

To quickly create a simple cardboard screen, you will need the following:

• cardboard sheets (you can take a single-color material or try to create a bright product with a combination of several shades);
• simple pencil;
• scissors.

Table 3. Instructions for making a simple cardboard screen

Steps, illustration	Description
	On sheets of durable cardboard, it is necessary to cut out fragments of the future screen according to the picture, which is presented below the table. The exact dimensions depend on the dimensions of the room and individual preferences. It is important to remember that there must be an even number of parts. All cuts are made with scissors, taking into account the openings for the grooves.
	Next, you need to connect the fragments with the help of grooves, inserting them into each other.
	Finished parts should be placed in a line, fastening to each other in grooves. In this way, a multi-row structure can be formed. The result is a decorative, but rather fragile partition.

Video - How to make a cardboard screen

Screen for creating a photo zone with fabric drapery

The option to create a screen was developed by the famous designer E. Teplitskaya, and such a design can be installed in your apartment or used to decorate a photo studio.

In working on creating a partition, you will need the following:

• metal parts for the base;
• fabric that can be draped (in this case it is organza);
• threads and needles for sewing;
• decorative rope;
• textile markers;

In addition, it will be necessary to prepare various decorative details for the future screen. It can be satin ribbons, pieces of fabric, laces, sequins - everything that, in your opinion, will organically fit into the design.

Step-by-step instruction

Step one: it is necessary to cut the fabric exactly according to the dimensions of the base of the screen. The width should be identical, and the length should be 20 centimeters more than the height itself (for bending). Drapery fabric needs to be pre-soaked in starch water - this will give it a denser structure.

Step two: the fabric should be fixed on the metal frame using special sewing needles. In this case, do not overtighten the material, it should be in folds.

Step three: using a textile marker, you need to make various patterns on the drapery. Beginners are advised to make primitive ornaments in the form of small dots, sticks. At this stage, it is worth including your imagination in the work.

Step four: paint from the marker will need to be dried with hot air.

Step five: metal carcass designs are also recommended to be decorated. You can use the same marker for such purposes, acrylic paints, different colored ribbons.

Decorative screen for a photo studio on a wooden frame with a grid

Such screens are used in photo studios to create unusual photographs. At the same time, you can make them yourself with the help of the following materials and tools:

• fine mesh;
• wooden planks;
• self-tapping screws of different lengths;
• furniture hinges;
• scissors;
• waterproof paint;
• PVA glue;
• staples;
• drill;
• brush;
• paint for wood.

Step-by-step instruction

Step one: it is necessary to determine the exact dimensions of the screen, and then mark the planks and assemble a solid frame from them (as in the previous case).

Step two: if necessary, you can paint the frame with paint or stain.

Use a furniture stapler

Step four: excess mesh must be cut with scissors.

Step six: the final step will be decorating the grid with paint. If desired, you can apply any patterns on the surface, and then decorate it with sparkles.

Summing up

Even such a simple interior element as a screen will allow you to use your creative abilities. Do not be afraid of experiments - designers prefer to combine different materials and decorations in the manufacture of partitions, so you can get an unusual, but at the same time functional product.

V Lately often visiting someone you can see homemade interior items from pallets or pallets. These are structures used to transport goods. , it turns out, it’s not so difficult to do, and in terms of quality it can even be better than that, which can be purchased at the store.

Video - DIY room divider