Making a barbecue from a gas cylinder: consider the stages of work. How to make an efficient stove from an old gas cylinder What can be done from a gas cylinder

Summer is a picnic season that cannot be imagined without kebabs and grilled vegetables. There are many ways to prepare food in nature, for which you need a barbecue. You can buy a ready-made structure in a store or place an order in a workshop. But it is better to make a brazier from a gas cylinder with your own hands. So you can get an exclusive product that meets the stated requirements and personal preferences.

Braziers are made from propane or oxygen cylinders having high quality metal. They are characterized by solid standard dimensions, regular geometric shape, good capacity, and the ability to arrange a large number of skewers. The height of the structure can be adjusted for the growth of the owner, which cannot be obtained from factory models. This will enable the person not to bend when cooking meat, but to stand upright.

Experienced craftsmen can, using their own imagination, using welding, fittings and metal, create unusual products who will become original decoration the exterior of a country house or summer cottage, which is clearly demonstrated by photos of barbecues from a cylinder.

The design of such a product is easy to manufacture. It is enough to carefully study the drawing of the barbecue with your own hands from a cylinder and, if you have minimal skills, create a structure. This option is the most budgetary. After all, the product is made from an old unusable cylinder, so the design basis will be free. Estimate how much a brazier made with my own hands, can be based on the cost of additional constituent elements of the structure.

Since the gas cylinder has thick walls, the finished structure will be able to withstand high pressure and high temperature without the risk of deformation of the product. Therefore, the service life of the barbecue increases. In addition, the bottom does not burn out during prolonged contact with an open fire, which means that after cooking there is no need to fill the product with water. If you make a brazier with a hinged lid, you can leave it outside without fear negative impact atmospheric precipitation. In addition, a brazier with a lid can be used as a home.

The design can be completed additional elements, which will increase its functionality. The brazier from the cylinder can be easily transported and installed to another place.

Among the disadvantages are the following:

due to its large dimensions, the structure may not fit into the interior of a small courtyard;
the brazier has a significant weight, so two people will be needed to move it;
the structure has a limited space for logs, so it is better to use coal as a raw material.

This will make it possible not to wait too long for the wood to burn out and there will be enough space for placing the skewers.

Brazier from a gas cylinder: construction options

Several options for barbecues can be made from an old gas cylinder:

traditional design without and with a lid;
B-B-Q;
smoker;
smokehouse.

The last three varieties differ from the classic type of barbecue. The barbecue is represented by a simple design, consisting of a part of a container, inside which there is a grid for placing products and an area for charcoal. The cut off part of the balloon will act as a lid and will be hinged.

There is a firebox in the smokehouse. In order for the structure to cope with the task at hand, it must be airtight. For this, half of the bottom of the product is removed. From metal sheets a firebox is made and welded to the main structure. A chimney is attached to it by means of welding, which helps to remove smoke from the smokehouse. After finishing the construction of the structure, it should be heated several times with wood and only then start smoking.

Helpful advice! For the manufacture of the firebox, you can use another cylinder.

The most complex and multifunctional structure is the smoker, which is also called a steam locomotive. To manufacture the structure, you will need several cylinders, each of which will perform its own function. This device combines the capabilities of a barbecue, barbecue, smokehouse and grill.

Necessary tools and materials for making a do-it-yourself barbecue from a cylinder

The basis of the design is a gas cylinder measuring 96 cm in length, 30 cm in width, with a volume of 50 liters. You can also create a brazier from a similar product of 80 liters, with an increased diameter, which contributes to increased comfort during firing up. This product is characterized by good capacity, allowing the use of the full length of standard skewers. This greatly facilitates the process of preparing barbecue for a large company.

There should be no external damage on the structure that could lead to the formation of small foci of corrosion, which, under the influence open fire and high temperatures will turn into holes. After a while, such a fate will befall the entire structure. Even if the grill is covered with heat-resistant paint, all defects will be found. Holes can be welded, but this will ruin the appearance of the product.

Helpful advice! To create a small mobile barbecue, you can use a traditional 27 liter cylinder.

Before making a brazier with your own hands, you should prepare the following materials and tools:

electric drill with metal drills;
welding machine;
clamps for fixing metal components;
pipe wrench;
grinder;
hammer;
chisel;
screwdrivers;
electrodes with a diameter of 4 mm;
stripping and cutting;
scribe;
drill brush attachment;
spray or brush for further coloring the product;
metal pipe with a diameter of 100 mm for the chimney;

a knee with a radius of 900;
door hinges;
metal corner;
metal handles that will be attached to the lid;
barbecue grill;
fasteners in the form of nuts, rivets, bolts;
priming;
paint;
solvents;
various decorative elements.

Preparatory stage before disassembling the cylinder

Before making the right brazier, you should prepare the balloon. It is necessary to remove the remaining gas from it by unscrewing the valve with an adjustable water wrench and a steel pipe used as a lever. It is quite problematic to remove the fitting on the cylinder, since it is securely soldered to the body. To prevent the container from turning, a stop angle should be attached to its bottom.

At the junction of the valve with the body, you can apply a "Vedashka" and wait a few hours until the thread peels off. The procedure is required only for outdoors, away from potential sources of ignition and other locations where ignition may occur.

Helpful advice! To make sure that the bottle is empty, soak the valve with soapy water. If it is bubbling, then the gas is still coming out.

After the cylinder is completely empty, it is recommended to turn it upside down so that all accumulated condensate will drain out. Next, the container is filled with water, which helps to displace all vapors and residues. For this water supply hose connects to the installation site of the crane. Water should be supplied under low pressure. This simple operation helps to prevent dangerous situations related to disassembly of the product. The tap is put in place, and the structure remains in this state for 2-3 days to remove all odors.

The optimal size of the barbecue: the implementation of the markup

While the water is in the cylinder, marking is performed according to a previously developed drawing of a barbecue from a gas cylinder with the indicated dimensions. Usually, for the barbecue, a product with a volume of 50 liters with an outer diameter of 96 cm is used. The dimensions of the barbecue from a gas cylinder: length - 98 cm, width - 30 cm, height excluding legs - 30 cm. This design is enough to cook six servings of barbecue.

It is convenient to mark out from the longitudinal seam. The diameter of the gas cylinder is divided into four equal parts - 24 cm each. From the seam, this value is deposited in both directions. To the right and left of the circular seams, 3 cm recede, and marks are placed every 8 cm.Thus, 6 marks are obtained for future placement of skewers. Holes with a diameter of 1 cm are drilled in them.

Helpful advice! Despite the fact that the grill from the cylinder is simple product, follows on initial stage make a small drawing of a barbecue from a gas cylinder with dimensions and an indication of the points of connection of individual elements.

From the line on which the marking was carried out, 10 cm is laid up, i.e. from the middle of the seam it turns out 34 cm. At this point, the barbecue cover will end, which is marked in the next step. It takes the distance between the first drawn line and the one just marked. A straight line is drawn between them, stepping back 3 cm from the circular welds. Also, from the initial marked strip, they are moved 10 cm down for the future fastening of the legs, which should be placed parallel to each other.

Helpful advice! If inside the product there are metal rings, the cut should be made in such a way as not to damage them. In the future, they can become the support for the lid.

How to make a brazier with your own hands from a balloon: a sequence of actions

Based on the markings made, the product is cut. You can study the process in detail on the video "Brazier from a gas cylinder with your own hands." To do this, it is recommended to use a grinder or gas cutter. The cut should start from the middle and work towards one of the edges. The grinder disk must be held perpendicular to the cylinder. Since the product has a large wall thickness and the cutting process takes place at a high intensity, in order to avoid premature disc burning, it is recommended to cut in some places not completely. These areas can then be eaten away with a chisel.

Related article:

Features and types of designs, interesting options design and photo, popular projects with drawings and step by step description manufacturing technology.

When cutting the balloon, it is necessary not to reach the circular seams by 3 cm. Having made a cut along one line, the loops should be welded. If you cut off the lid completely, the action will be more difficult, since the lid will have to be fixed at the same distance, which will be inconvenient to do alone.

To attach the hinges, clean and grind seats... The elements are riveted and welded. Next, proceed to the installation of fasteners. After that, the cutting of the cylinder along the lines is completed. In this case, the cover will rotate but not fall. At this stage, the water from the bottle can be drained. It is recommended to do this away from residential areas, since methane has a pungent odor that lasts for several days.

When making a removable cover, you should take care that it does not fall inside. For this, metal strips are welded to the transverse edges of the product.

So that the lid in the open position does not break the hinges, leaning back, it is required to weld a piece of the corner between the hinges along the cut line. Its width can be 3-4 cm. Such stops are made on both sides of the cover - left and right. By unbending the corners, the distance required to open the lid is adjusted. It is chosen in such a way that when closing this element it is not necessary to bend forward to reach the handle.

How to make a brazier from a gas cylinder: handles and openings for oxygen access

The next step is to weld on the handle. It can be of any kind and be made of various available materials that are resistant to heat. The most primitive option is to weld a piece of concave reinforcement appropriately. In this case, it is advisable to attach a piece of wood to it so that you can grab the handle. Such a part can be attached to the product using bolts.

To prevent the lid from falling through, it is necessary to weld from the inside to the cutout around the entire perimeter of the product a metal strip 2-3 mm thick and 3-3.5 cm wide. products (opposite each of the holes), cuts are made to the welded plate, which are necessary for installing skewers.

The next step is to make slots for air intake to the bottom of the product. This must be done because the structure of the building is closed. This means that coal and wood will burn badly in it without oxygen. To do this, the grill should be turned upside down. From the seam, 10 cm is deposited in both directions. A distance of 10-12 cm is measured from the resulting lines. Thus, longitudinal stripes of a given width are obtained. Slices are made across the strip every 5-7 cm for air intake. The strips can be replaced with holes, but a large number of them will be required, which will take a lot of time.

It is not recommended to make holes in the bottom of the cylinder. First, the factory seam should not be touched - this can lead to a decrease in the rigidity of the structure. Secondly, at the bottom, any holes are clogged with grease mixed with ash and ash. In the future, such a mixture can clog the holes and impair the flow of air.

The final step is to cut the tap and weld the resulting hole. Also, in this place, you can provide a metal pipe for removing smoke and ventilating the barbecue in a closed state. The brazier is ready, it remains to attach legs to it. You can see all the stages in detail on the photo selection "How to cook a brazier".

Making legs for a barbecue from a gas cylinder with your own hands

Do-it-yourself legs for a barbecue from a gas cylinder - the photos clearly confirm this - can be made from any material: fittings, a profile or round pipe, a strip of thick metal. The corners or pipes are sawn into four parts about 50-70 cm long. The elements are welded to the body in previously marked places at the same distance from each other so that they form a rectangle of the correct shape.

At the ends of the support legs, it is necessary to weld square metal plates, thanks to which the brazier will be more stable on the surface. You can also use two metal profiles connected parallel to the other two legs at the bottom of the product.

When making legs from sheet metal two strips 40 cm long and 20 cm wide should be cut. The ribbons are bent in the form of an arc along the diameter of the product. Legs are welded to their ends. Further, to create the necessary rigidity and strength, each pair of legs is attached below cross bar... A corner with a length corresponding to the value of the product is welded between the two posts.

Popular and simple option for the legs, a design from sewing machine... The brazier can be installed on wheels, which will make it easy to move it around the yard.
If you use a profile pipe for the legs, they will look like an inverted "T", and they can also be welded to the middle of the product. You can make a support in the form of a frame with a shelf at the bottom for placing firewood, coal, bowls, etc.

A good option is to make legs from rebar and round pipe. In this case, a portable structure can be obtained. Pieces of pipes of the required diameter are welded to the body of the barbecue, into which reinforcement rods of the required length are inserted. You can, on the contrary, weld pieces of reinforcement and put pieces of pipes on them. suitable diameter... However, it should be borne in mind that when the barbecue moves, the legs may fall out. Therefore, it is recommended to cut the threads for them. Manufacturing different options supports can be studied in the video "Brazier from a gas cylinder: manufacturing of support structures."

Barbecue coloring from a propane cylinder

To paint a barbecue, smokehouse, barbecue from a gas cylinder with your own hands, you should use heat-resistant paint, since the possible temperature in the barbecue can reach 800 0C. The painting should protect the metal from corrosion and temperature extremes when it comes into contact with a red-hot body. cold water... When heated, the coating should not emit elements harmful to human health and enter into a chemical reaction with other substances.

Before painting, the surface of the gas cylinder is cleaned of old paint... The procedure can be carried out using sandpaper or a special metal drill bit. Further, the entire surface is degreased with a solvent, acetone or alcohol and covered with a primer. The heat-resistant enamel should be mixed well before application until a homogeneous state is obtained. All clots and sediment must be removed from it. If the consistency is too thick, the paint is diluted with a small amount of solvent.

The paint is applied with a spray gun or a brush in several layers until a smooth and beautiful surface is obtained. Each coat must dry completely before applying the next one. Temperature environment should be above 20 ° C.

The most popular heat-resistant paints are acrylic mixtures in spray cans. With a unique composition, they are safe, effective, quick-drying and long-lasting. Also, the paint is characterized by anti-corrosion properties. It is sprayed at a distance of 20 cm and applied in several layers, each of which dries within 2 hours. The palette of shades is quite wide, but the most popular are silver and black.

Brazier from a gas cylinder: photo of product varieties

Using the instructions for making a brazier with your own hands from a gas cylinder, which you can buy ready-made from experienced craftsmen, it's easy to make a barbecue. For this, a corner is welded along the long side of the product body. The result is a shelf on which a lattice welded from reinforcement rods will be located. Convenient option there will be a division of zones in the barbecue grill with a net and a place for skewers. You can also create a stationary brazier. For this, small tables from the corners are welded on the sides and in front of the structure.

An alternative to staining - stylization of the "antique" barbecue

Another design option from a balloon is to create a brazier-smokehouse with your own hands. This device has an additional element in the form of a firebox. To create it, strips are cut from the bottom of the cylinder, then half of the bottom is cut out. Thus, a place is obtained for organizing the furnace, which is made of dense metal sheets with a thickness of 2-3 mm and is welded to the bottom. The result is a one-piece sealed structure, which is clearly shown in the photo of the smokehouse.

It is also necessary to organize here chimney... It can be purchased at a hardware store or made from a smaller diameter gas cylinder. It is recommended to improve the design and install a motor that will rotate the spit with meat, which can be seen on the video "Brazier-smokehouse with your own hands from a gas cylinder". Drawings, photos of which there are a large number on the Internet, will also help to complete the structure and get a multifunctional structure.

Another unique building is a brazier-steam locomotive. The design is made from several cylinders different diameters, barrels and main pipes. This product combines a brazier, smokehouse, barbecue and do it yourself. The structure is complemented by forged elements that give the structure an original and aesthetic appearance.

Using imagination and a creative creative approach, you can make a brazier in the form of a pig, a dog, a house and even a submarine, which is clearly demonstrated by photos of braziers from a gas cylinder with your own hands.

How to make a brazier from car disks

The brazier from car disks combines a barbecue, a smokehouse, hob and grill from a gas cylinder. The metal structure can be made from old wheel rims from the car. You should take those that are made of solid steel, and not of an aluminum alloy.

Brazier from car drives performed in various ways. For the simplest design, one element is sufficient. The inner part is cut out of it, forming a container similar to a kettle. If there are too large holes in the bottom, a metal plate must be provided. However, the openings should not be completely covered as the coals must be blown through to maintain the heat. On the sides of the bottom, you need to weld the legs from the pipe.

On such a grill, you can fry not only a kebab strung on a skewer, but also prepare a barbecue. For this, the structure should be covered with a metal grill. It would be more expedient to make it removable. For the convenience of moving the barbecue symmetrically on the sides of the structure, handles are welded. To maintain the heat, a window can be made on the side of the disc.

To cook a brazier more complex design, you need two disks of the same size. On one of them, a partition is cut out using a gas cutter. The elements are placed on top of each other and welded around the perimeter. The baffle of the second disc is the bottom for the first. It will be convenient to place a bowler hat here. In the side of the lower disc there is a window for throwing firewood.

Another noteworthy option is to weld two elements to each other, which have a pre-cut in the middle. In the side of the structure, a window is made through which firewood is fed into the firebox. The upper part of the structure is equipped with a grill that turns the grill into a barbecue.

How to make a barbecue from a barrel and pipe

To create a barbecue from a barrel, you will need a container with a volume of 50-60 liters with a diameter of 40-50 cm. The product must have a wall with a thickness of 2-3 mm. You can create two grills from a barrel. To do this, cut the product in half.

The manufacturing process of the structure is similar to the creation of a grill-smokehouse from a gas cylinder. Only the dimensions of the product will differ, on the basis of which the markings are made for future cutting. However on preparatory stage no need to fill the container with water. In the side part, cut a round hole on top for the chimney, and at the bottom for ventilation.

A good solution is also to use another barrel mounted on the side lid as a pedestal, where a full-fledged smokehouse is organized. To create a structure, you can use the drawings found on the Internet.

Helpful advice! A 27L gas can can be attached next to the barrel, which can be used as a storage location for coal.

The construction is quite often performed from metal pipe... This is a more time consuming option that requires the use of additional material. A metal sheet is used to create the walls of the structure. If a smoke exhaust pipe is provided, its diameter should be 70-100 mm.

Important! For the barbecue, you should not use a barrel of fuels and lubricants. The specific smell cannot be eliminated by anything.

Today you can buy a ready-made grill from a gas cylinder, the price of which is on average 5,000 rubles. but homemade construction is even cheaper and can last for many years with proper use and care. Equipping with additional elements a grill from a gas cylinder, which can be bought in specialized stores, you will receive a multifunctional facility for smoking, grilling and barbecue. A creative approach to the design of the product will allow you to create an original design that can decorate a site.

Making a barbecue, grill, barbecue, smokehouse with your own hands from a gas cylinder: video instruction

In many private households there is an old LPG cylinder. Many useful things can be made from this object, for example, a simple heating device.

If there is a desire and a welding machine, then a potbelly stove from a gas cylinder with your own hands can be made without any problems. Of course, some additional materials will be needed.

Potbelly stove - a primitive version of the metal. Such a device works extremely simply: they put firewood in the firebox, they burn, the furnace body heats up and gives off heat to the surrounding air. Flue gases are removed through the chimney, and the ash is poured through the grate into the ash pan, which should be periodically cleaned.

Stove stove is also heated with other combustible materials: diesel fuel, coal, peat, household waste etc. If desired, you can cook quite successfully on such a stove. This point should be thought out even before the manufacture of the structure begins, in order to make a flat hob.

The potbelly stove is a thick metal combustion chamber with a loading door, chimney, grate and blower. An old gas cylinder can be used as a body

For the stove, you need to choose a special place, finished with fire-resistant materials. It is advisable that she stand to the side, where no one accidentally touches the body and does not get burned.

If desired, the upper part of the vertical stove from an old gas cylinder can be turned into a modest-sized hob

Such a metal structure weighs a lot, so we are not talking about any mobility of the device. Move the stove for heating different premises it will be difficult.

These ovens are usually used to heat utility rooms in which there is no electricity or where it is supplied intermittently: garage, shed, workshop, etc.

From two gas cylinders connected perpendicularly, you can make an improved version of the stove, which allows you to store more heat and get high efficiency when burning fuel

Another problem is the low efficiency, since part of the thermal energy during the combustion of wood literally flies into the chimney. Exists different ways keep warm and slightly modify the stove to make it work more efficiently.

Finally, you need to take care of good ventilation of the room in which the stove is installed, since such a device burns a large amount of oxygen during operation.

So, a potbelly stove consists of a metal case, the role of which is usually “invited” to an old gas cylinder. In the case, you need to make two doors: a large and a small one. The first is used to load fuel, the second is needed as a blower through which air flows from the combustion chamber to ensure the combustion process and traction.

To begin with, it is recommended to open the bottle and bleed off the remaining gas. Of course, this should be done outdoors, not indoors. Then you need to drain the remaining liquid condensed inside from the cylinder. This substance is usually harsh and bad smell Therefore, it is best to prepare a small container with a lid for it in advance so that you can carefully package it and discard it right away.

There are no particularly strict requirements for the parameters of the stove stove design. The larger the combustion chamber, the more spacious the room can heat the unit

If condensation is accidentally spilled on the floor of the room, the specific aroma may persist for a very long time... After all these operations, the cylinder is still not ready for contact with the welding machine, because residual gas vapors remain inside.

It is necessary to fill the cylinder with water to the very top in order to completely displace all the gas from it. After that, the water is drained, now the balloon can be cut without problems.

Stage 2 - manufacturing and filling of the case

Next, you need to select the type of potbelly stove from the cylinder, whether the cylindrical body will be located horizontally or vertically. All other operations are carried out with this orientation in mind. If the horizontal position is selected, then one of the ends of the cylinder will serve as the back wall, and on the other you need to install a loading door and a blower.

If you plan to make a vertical stove from a gas cylinder, you will need to make two holes: for loading fuel and for a blower with an ash pan

Thick reinforcing wire can be used for the grate. In order not to cook a grate out of it, you can bend it with a frequent zigzag, "snake". This structure is welded to inner walls metal case.

The front wall is made of sheet metal as follows:

The metal must be applied to the front of the stove to apply the markings.
A round part should be cut out according to the marking.
Apply one more mark on it: for a rectangular door and a blower.
Cut holes according to the marking.
Make doors.
Weld the hinges, locks to the front wall and hang the doors.
Weld the wall with doors to the body.

Both doors should be sealed along the contour with an asbestos-cement cord so that they fit well to the body. The back wall in such a potbelly stove usually does not need to be done, its role is played by the bottom of the cylinder. At the top of the case, close to back wall, you need to make a hole for the chimney.

The pipe must be taken from thick metal, since the lower part of the chimney will be in contact with heated flue gases. Thin metal in this place will quickly burn out. Now solid legs are welded to the bottom of the stove from reinforcement, pieces of metal or pieces metal corner... They must support both the weight of the structure itself and the fuel that will be loaded into it.

Roughly the same technology is used to make a vertical potbelly stove from a cylinder. The bottom of the cylinder will become bottom construction, at the top you need to make a cylindrical "roof" with a hole for the chimney. Usually the top of the balloon is cut off. At the end of the installation, it will be possible to weld it back on. Doors - for loading and blowing - are made in the front of the cylinder body.

Such a potbelly stove will take up less space than the horizontal version, and it will also be higher. If it is supposed not only to heat the room, but also to cook food, then it will be necessary to adjust the height of the stove taking this moment into account and ensure an even hob.

But usually the diameter of the cylinder is not large enough to provide a full cooking opportunity. Boiling the kettle is a doable task though.

The grate can be made in the same way as described above: from fittings bent by a snake along the pipe diameter. It is welded between the loading and blower holes.

Some try to reduce the amount of welding required by leaving the top of the cylinder virtually untouched. But then all other work will be more difficult to perform.

In a horizontal potbelly stove, you can not weld the grate, but turn a part of the body into it by drilling holes of a suitable diameter and attaching an ash box below

For example, the grate will have to be inserted not from above, but inserted into the furnace door and somehow held in correct position... Now you need to make doors with hinges and locks and weld them to the stove body, pre-sealing with an asbestos-cement cord. It remains to install the chimney at the top, and weld the legs at the bottom.

Stage 3 - making the door and ash pan

Doors for a potbelly stove can be made from those parts of the body that remained after cutting out the holes. Hinges and latches are welded to them. These are simple elements. Loops can even be made from thick chain links. The second, more expensive, option is to buy ready-made structures cast metal.

You can choose between two separate doors: a large one for the inlet and a narrow one for the blower. But there are also kits in which such doors are combined into a single structure.

Holes for such doors must be cut exactly to size. After that, you need to weld the frame from the corner to the edges of the openings.

Several links of a thick bicycle-like chain can be used as hinges for a homemade potbelly stove door made from a cylinder

The frame of the cast doors is attached to the resulting frame with bolts. It is recommended to pre-weld a small side so that there are no gaps and the oven closes hermetically.

In small potbelly stoves, you can, if you wish, do without a grate at all.

On the left is an inverted case of a horizontal stove with an ash pan welded to it, and on the right - general form... The ash pan is pulled out in order to regulate the flow of oxygen, the blower in such a model does not need to be done

Finding a place for her is difficult if they make a stove small size or low, for example, a horizontal version. In such a device, no blowing is made; air is provided with the help of a loading door, which is simply opened slightly. Rebar grates are easy to make, but they are not particularly reliable.

Over time, the fittings burn out, they have to be replaced. An alternative is a piece of sheet metal that has slots or holes cut into it. round shape... To collect ash, you can use a special box - an ash pan.

In the horizontal version, stove stoves from a cylinder can be installed in the lower part, complete with an ash pan, since lower part the enclosures will have to be cut to facilitate installation.

How to improve efficiency?

To make the stove work more efficient, there are several simple ways... To begin with, you should insulate the chimney in order to retain some of the heat that goes away with the flue gases. Can be used different methods to increase the area of contact of the heated metal with the ambient air.

Some experts recommend making the chimney not strictly vertical, but curved. This will increase the path of combustion waste and allow some of its heat to return to the room. But it should be remembered that the complicated design of the chimney can adversely affect the draft, so you should not get carried away with excessive bends.

Sometimes metal wings are welded to the body of the stove, for example, made from a corner or any suitable strips of metal. If the dimensions of the stove allow, you can weld a horizontal sheet of metal on top and make an additional hole in it not for the chimney, but for a saucepan or kettle.

The hole is closed with a special compound cover made of several concentric circles. By removing or adding circles, you can adjust the degree of heating.

Another option for modernizing a potbelly stove is a brick case. The masonry is carried out around the stove, while leaving a small gap between the metal body and the brick. The brick will absorb some of the thermal energy, and then gradually give it to the surrounding air.

If you wrap the chimney with a metal mesh and place stones in the gap, you can increase the heating efficiency. Even after the firewood burns out, the stones will give off heat for some time.

An alternative version of such a modernization is a metal mesh around the chimney, in which pieces of brick or stone are laid. This is a popular solution for stoves installed in a sauna, a variation of the heater. But it should be remembered that only river "pebbles" of a uniform color and without blotches are suitable for this. If the stone is made up of layers different types, it can rupture when exposed to high temperatures.

If you need a solid-sized oven, the master has two gas cylinders at his disposal, you can combine them into one design. One of them is installed horizontally, and the second is placed vertically as a branch pipe for a chimney. The heating area increases, such a potbelly stove will work more efficiently.

Metal pipes built into the stove body, in combination with a fan, allow you to increase the speed of warming up the room, but to achieve this effect, you will need electricity

Finally, you can insert pipes into the upper part of the body through which the air will circulate. If you put a fan at the end of these pipes, the air will move faster. This equivalent of a fan heater will warm up the entire room in a few minutes and distribute heat energy more efficiently.

Conclusions and useful video on the topic

This video tells about the procedure for making a stove from a gas cylinder:

An original potbelly stove with the function of pyrolysis afterburning of fuel can be made from two gas cylinders:

A potbelly stove is a simple device that is not difficult to build and can be widely used. If the order of work is thought out in advance and correctly executed, such a stove can last long enough.

Please write comments on the article, ask questions, share your experience if you have already had to collect a stove from scrap materials.

The clean air and the beautiful surroundings help you relax and replenish your energy reserves, especially if you enjoy your own meals, such as kebabs or vegetables baked on the fire, at the same time. Successful culinary delights will help you gain confidence in your own abilities and inspire you to new feats, for example, tell you how to make a brazier from a gas cylinder with your own hands. And if you turn on your imagination while assembling the barbecue, you can get a unique piece of decor. Using the drawings, you can build such a structure using available materials: a pipe and a gas cylinder.

Brazier is a favorite option for cooking on charcoal.

Transportable.
Brazier, which is comfortable to take with you on trips. It does not take up much space in the car and does not require much time for assembly and disassembly.
Portable.
At times more than the previous one, it is allowed to move it over short distances. Suitable for suburban areas.

Constant.
Barbecue built into the foundation.

Raw materials for the construction of barbecues are very different. Constants are often built from stones. Transportable or portable smelted from aluminum or steel.

Heat resistant material;
The material is required to keep warm;
Size according to your needs.

Experimenters have discovered a huge variety of options, the creation of which involves a wide variety of raw materials. Among them, not the last place is occupied by a grill from a gas cylinder.

Production technology

Instruments

Angle Grinder;
Drill;
Gas cylinder with a volume of 50 liters.
Hinges;
Steel pipe;
Welding;
Aluminum studs.

To implement the barbecue design idea, you need to select the production material. The foundation will be a gas cylinder equal to 610 millimeters long, 27 liters in volume, 292 millimeters in diameter and more than 3 millimeters thick with walls. In order to save money, used cylinders are used, in this regard, it is necessary to carefully inspect the cylinder for damage.

For the production of legs, it is better to use steel round tube... In addition to the barbecue, you can make a grill net by cutting the workpiece according to the internal parameters of the barbecue.

Preparatory process

Care must be taken when cutting the gas cylinder and the instructions must be followed carefully. Gas vapors may have been retained during use. In order to finally eliminate them, you need to put the cylinder upside down and unscrew the valve. To make sure that the gas is escaping, lubricate the valve opening with soap, which will foam at the outlet, and you will be able to make sure that the process has started.

Fill the bottle with water to destroy the remaining gas.

When filling with liquid, use a hose for added comfort. Shake the can as it fills with water until it is full. It is recommended to remove the water from the cylinder as far from the house as possible, only after that you can start disassembling the cylinder.

It is important that this procedure is performed by two people. The first person should cut down the tap, and the second person pour water on it so that frictional force does not cause ignition.

Work should be carried out in an open space. Saw off the valve with a grinder. Remove the paint with a grinder and inspect the base for damage. Minor rejects are processed until they disappear completely without significant changes in thickness. After that, we put the cylinder on the ground and draw a line along which we will cut the container in the future.

Detailed instructions

We cut the container.

Using an angle grinder, we cut the cylinder in half - we use one part as the base of the barbecue, and install the other as a cover. You need to cut along the joint line or as far as possible nearby. The thickness of the walls of the cylinder in almost all cases is no more than three millimeters, in this regard, the division procedure will not be too difficult, this can be done with a grinder. The main thing is to cut it very carefully so as not to spoil the flank rings that are intended for the cap - as a result, we will have the perfect support for our barbecue.

The side edges should not be removed so that the draft does not extinguish the fire in the fire you are creating. Then, using a drill, we make several holes on the base and sides, in order to make light ventilation.

We kindly ask you to observe safety precautions during all these procedures! It is necessary to put on some protection on the hands and face. To prevent deformation during sawing, the cut line is poured with water.

Installing the legs.
The next step is to install the legs for our future barbecue. It is necessary to firmly substantiate the structure on the ground, so that after that it can be easily put on the cover. Select the length of the legs based on its possible movement, as well as based on personal needs. Based on this, we can conclude that an acceptable height is 20-30 centimeters. If possible, you can attach the legs from sewing machine or steel tubes... To connect the pipe, you need to make four small holes in the base of the barbecue, in which to place the bolts with the threads on the outside. They can be melted or screwed on with nuts.

Cover assembly.

The barbecue hood is installed on hinges, which are fixed with pins, and then welded to the base. You have the option of making the hood portable when installing one-way awnings. Welding the hinges is a mandatory procedure, since under the influence high temperatures rivets fall off. Conversely, the lid holder can be bolted. The handle must be made of heat-resistant material. With the help of a corner, it is possible to make a stopper for the cap. A chimney can be installed in a separately made hole.

Final details.
It is necessary to make recesses for skewers on the end side. Their number depends on the height of the container. A convenient distance is 25 centimeters.

The brazier can change shape over time under the influence of high temperature; to avoid this, you can weld a corner to the edges. It enhances the perimeter resistance. Holes are made at the base of the barbecue so that the ashes are not removed by hand.
The final step is painting. This point is carried out depending on personal interests.

Smokehouse - barbecue

The main distinguishing feature of the smokehouse is its airtightness. The assembly technique is exactly the same as described earlier, with only one point that, in addition to the basic structure, we attach a combustion chamber or, in another way, a firebox. In this case, cut off half of the lower part - this is the section for the oven. The combustion chamber itself is made from iron sheets or from a smaller cylinder. The final oven is attached to the barbecue. The necessary part of the smokehouse is one that you can buy in a warehouse or do it yourself. Before starting to smoke food, it is necessary to fire it with wood until the traces of gas are neutralized.

"Locomotive"
The structure, called the "steam locomotive", contains several devices at the same time: a brazier, a smokehouse, a barbecue and a grill. It is made from a small number of containers, each of which fulfills a specific mission.
Visually, this design really resembles a steam locomotive, in particular, if you think over its design. The auxiliary structure is equipped with various functional little things that can also play the role of decorations. On one brazier-steam locomotive, it is possible to perform actions with several parts at once: fry meat on the grill, cook vegetables and smoke food.
It is recommended to paint this barbecue with heat-resistant paint, since the heat in a steam locomotive can exceed 700 degrees.

With an insignificant investment of time and effort, it is possible to realize the most ingenious, and sometimes even strange ideas. From the simplest balloon, create a bright component of your patio. We wish you success!

Good day!

Today we will talk again about how to make a brazier with our own hands. But this time a gas cylinder will serve as the material for its manufacture.

Someone will say that it is difficult, cumbersome and not aesthetically pleasing. However, if to this issue get creative enough, then you can get something like this:

So, who nevertheless decided to use this material for the manufacture of a barbecue, read the article further. We will analyze here how to make such a grill. Below is a diagram of such a barbecue.

How to make a brazier from a gas cylinder with your own hands?

It is best to use a gas cylinder with a volume of 50 liters for the barbecue. Before proceeding with the manufacture of the barbecue, the cylinder must be prepared. This process includes a complete release of gas from it and flushing.

CAUTION - FIRE AND EXPLOSION HAZARD !!! Within the framework of this article, it will not be told about the release of gas from the cylinder and its disassembly. Since this requires a special preliminary preparation, and an understanding of tool handling and safety. We recommend that you familiarize yourself with the materials on YouTube videos by entering a similar request. It is important to understand all the points and nuances before starting to saw the barbecue cylinder. You need to be extremely careful, and it is advisable to watch the video with two people. Moments regarding the parsing of the cylinder require not only preparation, but also the ability to work with the tool, and spark arresters in the form of water may also be required. All the nuances can be learned from many videos, and special training.

When the vent is opened (in some cylinders, after the gas is released, it is enough to unscrew it with a key. But this is a rarity!)

Then, under pressure, we supply water to the cylinder. In this case, the balloon must be shaken well. The water in the bottle remains for several days, after which we drain it. This is necessary so that no special substance from the gas remains on the walls. The fact is that this plaque remains after the gas is released and is also combustible and explosive.

Then….

You can start making the barbecue. To do this, we need the following tools and materials: a grinder, a drill, a welding machine, steel pipes for the legs, metal hinges and a handle for the lid.

The circumference of the balloon is 96 cm, so it is very convenient to divide it into 4 parts. And the weld seam, which runs along the entire length of the cylinder, will help to do this. We retreat from it on both sides by 24 cm and draw a line. Next, mark the holes for the skewers. We find transverse seams (welding rings) along the perimeter of the cylinder and retreat 3 cm from them. These are extreme marks. We mark the intermediate ones at a distance of 8 cm. So we get a place for 6 skewers.

Now, with a grinder, we cut the cylinder along the two longitudinal lines outlined earlier. The thickness of the metal is 3 mm .. therefore it is not difficult to cut it. It is best to start cutting first along the longitudinal lines, and then along the transverse ones.

Cross-cuts must be done, stepping back 10-15 mm from the welded seams, since in these places the metal is double, and therefore. indentation will save time and part of the grinder's circle. In addition, the lid of the barbecue grill will lie much better on the bottom layer.

As soon as the wall has been cut, it is necessary to make cuts for the skewers. Slightly below we make cuts or drill holes for the passage of air with a drill. We make similar holes at the bottom of the barbecue. Without cuts and holes, we leave only the bottom of the barbecue and its lid.

So that the metal of the cylinder does not lead from high temperatures, it is necessary to weld a 32 * 32 corner around the edges of the cut. With the help of clamps, the corner can be pressed against the body without gaps. This corner can serve as a support for a grate or skewers. The corner must be welded inside the body next to the hinges.

At the last stage, we make legs on which we install the brazier itself. The height of the legs should be such that it would be convenient to work at the barbecue. Usually it is about 20-30 cm. Pipes are optimal for the legs. You can also use a channel. The configuration of the legs can be very diverse, it all depends on imagination and capabilities.

That is, in general, the whole procedure for making a barbecue from a gas cylinder. If you are a master of gas welding and cutting, or your friend who possesses these qualities makes you a brazier, then you can show your imagination and supplement your product with some decorative elements.

If you need to have not only a brazier, but also a smokehouse, then you will need to attach a chimney pipe to one side wall, and weld the firebox to the other wall. When you close the lid of the grill, you will have a wonderful smoker.

If you paint your grill, it will look much better, and it will last longer.

Before using the barbecue, it is necessary to heat it several times so that the smell of gas disappears completely.

You can also put cast iron grates on the bottom of the barbecue. This will give additional ventilation inside the barbecue. In addition, hot grates will save coal as they also participate in the frying process.

Drawings and photos:

It would seem that everything is clear even without drawings for the manufacture of a barbecue, but why invent a bicycle when it has already been invented. If you have ready-made drawings of a barbecue from a gas cylinder, then it will be much easier to make it. At least you will have a choice of the most interesting option.

Below are some interesting drawings of a barbecue from a gas cylinder.

And these photos show, in my opinion, quite interesting and original designs braziers

Master class: grill from a gas cylinder in three hours

If the description and pictures about the manufacture of a barbecue from a gas cylinder are not enough for you, then watch this short video.

It shows quite clearly how to make a perfectly acceptable brazier out of an ordinary gas cylinder.

The brazier is popular with those who like to relax. big company in the country. Standard Sizes steel versions of the brazier and shashlik, which are presented in stores, are suitable only for cooking a few pieces of meat. It is inconvenient to make steaks and kebabs on a brick building. Not everyone dares to make a stationary structure for a barbecue. It is much easier to make a brazier from a car gas cylinder with your own hands.

To build a brazier stove from a propane gas cylinder with your own hands, you will need a 50-liter container with a height of about 1.2 meters. These dimensions are most suitable for a rocket brazier. You can buy a gas cylinder in any specialized store or order it on the Internet portal. Online shopping is cheaper. If you plan to take the product from an offline store, it is better to give preference to Moscow firms. Indeed, large companies operate in the capital, the cost of products for which is lower average price around the country. In addition, such organizations often offer free shipping.

To create a hot smoked brazier, you will need the following tools:

Drill.
Chisel.
Hammer.
Bulgarian.
Metal corner.
Screwdriver.
The tube is metal.
Door hinges in the amount of two pieces.
Adjustable wrench.

On average, a homemade design will cost 2,500 rubles. It is inexpensive, especially when you consider that a ready-made high-quality grill costs at least 15,000 rubles. The only drawback of a gas cylinder brazier is the increased fuel consumption in winter. Because the metal, due to its low heat capacity, cools down quickly. Check out the article about.

Making a homemade barbecue from a gas cylinder

To create an open small barbecue from a freon gas cylinder, no drawings are needed. With barbecue, too, there are no difficulties. A single correct scheme does not exist.

That's why metal structure should be done based on personal preferences and the way of cooking.

If you intend to use ready-made coals and a grate, then it is recommended to make the distance between them small. It is enough to evenly cut the cylinder or barrel along the middle. If the summer resident plans to use skewers, the lid will have to be made smaller in height than the base.

Reviews of homemade cauldrons, barbecues from a gas cylinder or rims are mostly positive: the work is not difficult and does not require special knowledge and skills. And there are a huge number of manufacturing options, which can be viewed in the pictures on the Internet.

The step-by-step instructions are given below:

Flush the bottle.
Cut it into two equal parts lengthwise if you plan to use a regular grill. Or cut a rectangle in it if you are designing a barbecue.
Decide on the height of the barbecue and make legs and a stand. They are carried out from pipes. Drill four holes at the bottom of the base. Insert the bolts, fix them with nuts.
Install the cover. For this, holes are made for the hinges. Fixed with rivets and welded.
If a removable cover is planned, then metal strips are attached to the edges of the barbecue.

Open type, no lid

A brazier without a lid is the easiest to make yourself. To convert an old gas cylinder into a brazier, cut the container in half and drill holes in the sides for air intake. Usually, one half of a gas cylinder is enough to create such a product. It is installed on a support made of stones, bricks, or simply on an earthen embankment. You can also make legs and weld them to the bottom.

The manufacture of such a structure takes a minimum amount of time. But in use, the grill will not be convenient. And its appearance is not particularly attractive. Therefore, in front of friends there will be nothing to brag about. Many experts advise: if you have even small skills in welding, forging, it is better to try to make some more interesting model. For example, a brazier in the form of a steam locomotive or a pig.

How to make a barbecue?

Structurally, a barbecue is a more complex option than a barbecue without a lid. The bottom line is that the side of the cylinder is cut off and attached to the hinges - a door is obtained. A place is made inside the container for coals, a grid for frying food is installed.

To give the homemade barbecue and hearth functionality, improve the air supply to the stove. To do this, do the following work:

If desired, you can modify the design. For example, build a canopy, make shelves, weld a chimney for good traction. To make it convenient to transport the barbecue, two legs are equipped with wheels, and the third is used to stop. It is advisable to make the handle for transportation long. It is convenient to place a board for spices and dishes on it.

Features of a homemade smokehouse

The smokehouse differs from the usual barbecue in its tightness and the presence of a firebox. To make such a structure, you first need to draw up a project. It is easy to find a suitable circuit on the internet. Next, you should inspect the gas cylinder. If the surface is corroded, the product is not suitable for a smokehouse. If the cylinder is new, the gas must be drained by unscrewing the valve. Then the container is cut into two parts and connected with hinges. Fix the handles and weld the legs. A lattice is inserted inside the container. The portable homemade smoker is ready.

Concerning stationary options, they are made a little differently. From the edge of the cylinder, where there is a welded seam, an indent is made and a line is drawn three centimeters below the perimeter. You should get two circles. Cut the balloon in the middle with straight lines (to prevent the formation of fire, the vessel is pre-filled with water). It turns out the lid in a curved form and the cutout of the smokehouse. Exists different variants smokehouse performance. When the work is completed, the product is checked for stability. Usually, if the legs are long, the structure is not securely on the ground. Therefore, in addition, corners are installed at the bottom of the legs.

Do-it-yourself smoker

If you already have experience in creating a barbecue from a gas cylinder, you can try to make a smoker that will combine two functions: smoking and frying food. To do this, you will need two cylinders with a volume of 27 and 50 liters, a welding machine, rods for the bed, a pipe elbow, electrodes, a piece of a meter pipe with a diameter of about 15 centimeters.

The grill smoker is created in this way:

Unusual options for barbecues

You won't surprise anyone with ordinary barbecues from gas cylinders, so summer residents are trying to create unusual options that do not differ in functionality from modern factory designs.

For example, a brazier is made in the form of a steam locomotive or a pig. In this case, you do not need to buy special materials. It turns out such a barbecue is cheap, but it looks original. The main thing is to know the principles of welding and understand how to make a brazier with your own hands, so that it performs all its functions to the fullest and serves for a long time.

How to cook a steam locomotive?

The design in the form of a steam locomotive combines a brazier, grill, smokehouse and barbecue. Outwardly, the product really looks like a steam locomotive. Such a model is built from several cylinders, main pipes and barrels. Each pipe has its own purpose. Steam locomotives with pipes of different diameters look especially good.

To create a brazier-steam locomotive, you will need three gas vessels. Side bases are suitable as supports. sewing machine... The container on the right side serves as a barbecue, in the middle - a barbecue. The first balloon is placed vertically and a circle with the diameter of the horizontal middle balloon is cut out on the side. On the middle vessel, the leftmost part is cut off and the balloon is welded to the first container. A third cylinder with a cutout on the side is also welded to the second cylinder. A pipe is installed on a vertical vessel and a damper is made. A temperature sensor is installed on the first and second containers. A door is made in each cylinder: it is cut out and connected with the help of awnings. Iron arc-shaped pieces are welded onto the door, which will serve as handles.

The wheels are made from the remaining parts of the cylinders. But, to add style and originality, many use forging elements. It is recommended to install sliding grids, tables and other functional parts. It is important after creating a brazier-steam locomotive to completely cover it special paint up to 1000 degrees. It is easy to get burned on such a product without a heat-resistant coating.

Piglet and pig

The brazier, created in the form of a pig, a pig, looks interesting. Only one old gas cylinder is required for manufacturing. The container is placed horizontally and the lid is cut out, as is the case with the creation of a conventional smokehouse. The lid is hinged. The legs are made of metal pipes. In order for them to securely hold the structure, a lattice is installed in the middle of their length. The nose and mouth are made from pieces of metal pipe. The ears are cut from metal sheets, iron and welded to the part of the vessel that serves as the head of the pig. It is recommended to use forging elements.

There are many photos and videos on the Internet showing how such a brazier looks like and how it is created. You can make a brazier in the shape of a pig in just a couple of days. The main thing is to be able to work with the welding tool and be familiar with the forging technique.

The final stage is painting

The paint protects metal surface from rust, as well as the temperature difference that occurs during the use of the barbecue. For coloring at home, a heat-resistant composition is used that can withstand up to +700 degrees. In this case, the coverage will have to be periodically renewed.

The stages of painting are shown below:

Clean the surface of the gas cylinder from the old coating. To do this, use sandpaper.
Degrease with acetone, solvent or alcohol.
The heat-resistant paint is mixed until a uniform consistency is obtained. All clots and sediment are removed. If the solution is too thick, add a little solvent.
Are applied coloring composition roller or brush. To make the surface smooth and beautiful, you will need to paint in several layers. Allow time for drying from 30 minutes to 2 hours.
It all depends on the type of paint.

If you plan to paint the barbecue outside, the air temperature should not be higher than +40 and below +20 degrees. What paint should be applied to the structure so that it does not rust? Most often used are waterproof acrylic paints in aerosol cans or burnished with oil. They dry quickly, are durable, safe and have anti-corrosion properties.