How to make a partition in the bath: materials and construction technologies. Partition between a steam room and a rest room from which to make the inner walls in the bath

The partition between the washing and steam room of the bath can be performed in several ways. The most common option is the manufacture of a wooden frame, in second place is a solid serbic partition, the manufacture of which is quite expensive. And the last way to divide two rooms implies the arrangement of a solid brick wall thickness in the Pollipich.

Optimal partition design

We will look at the wood-cutting partition from the tree as the most simple in the manufacture. Metal racks are also used as the base of the frame side, but this option is applied noticeably less often, as the metal is inclined to destroy under long exposure to high humidity.

The wooden partition is manufactured quite quickly and does not require large financial and labor costs, compared with whole walls from a bar or brick. At the same time, the airspace in voids between the frame elements is the cause of condensate formation at the points of the temperature difference between the heated parillery and colder air inside the partition.

An important question when choosing a type of partition - to insulate it or not? Here again, you can return to comparing different types of simpleness. Before the whole partition from the bar, brick or block, this question is not at all. By itself, the dense material of such walls will be at the necessary degree to protect the washing separation from overheating. At the same time, it does not have sufficiently high heat insulating indicators so that it is not to pass warmly into the oil.

How to make a partition with your own hands?

The first thing is made by a wooden frame, when the arrangement of which special attention should be paid to its fastenings to the walls. This is important in the case when the bath is made of fresh bar or logs. These types of buildings inevitably give shrink on time, which should be taken into account when creating any internal partitions.

The partition in the photo above is mounted on the walls using special metal fasteners designed to create the so-called "sliding partition". The corner is fixed motionless of the stainless bar, and the installation of the cutting wall is made on stainless self-tapping screws so that they can move inside the vertical groove of the attachment.

An alternative will be a wooden sliding design device, without the use of metal corners.

To the ceiling, the partition is fixed with a metal fastening with vertical grooves. In them, by analogy with wall corners, stainless self-tapping screws are screwed, which over time will move along these grooves.

On top of a wooden frame from the side of the steam, foil vapor insulation on kraft paper is stacked. All the joints of the material are sampled by foil scotch. There should be no unlucky holes and damage to the parobacrol layer so that the moisture does not penetrate into the common.

As can be seen in the photo, the surface of the floor on the floor has a small tile base. The tile is mounted over the slabs of the CML or CSP on a special glue. The plates are attached directly to the frame or on the sliding structure, if there is an adjunct to the walls of the log.

The fitting of the finishing finish of the partition from the steam partition is made on the crate, in this case it is lining.

Important moment - the place of the walls of the walls to the floor. Here it is necessary to carefully trace the layer of steam-savings to be continuous.

Warm or not?

About warming framework It is worth saying that here you should look in the circumstance, taking into account the characteristics of a particular bath. First of all, it is necessary to determine how much wave needed. If in the design of the bathroom, the washing room around the perimeter of external walls has a good heat shield or in the wall between the oil and the steam room is placed a brick shield or part of the brick furnace wage, it is obvious that in the additional warm-up, the warehouse does not need.

In the absence of need to additionally heat the waters, in the frame between it and the steam room can be laid thermal insulation. It will give the opportunity to preserve more heat in the steam room, as a result of which it will warm up faster and slower to cool. In addition, the use of a warmed partition guarantees the protection of the washing from overheating, which often happens in the baths that have good thermal insulation of the exterior walls of the structure.

In the bath and washer and the steam room have high humidity and in each of these premises, as a rule, installation of a steamproof film is carried out to protect the wooden frame from a large amount of moisture in the air of both branches. If the plates of Minvati are in the simpleness, then they, even with the creation of hermetic protection against moisture on both sides, will still collect moisture, and there is no place to evaporate.

Thus, it can be concluded that if you need sufficient heat insulation with overheating, it is necessary to install a one-piece partition from a bar or a thick board without cracks and free space inside the simpleness. This design will allow you to isolate the washing from the active heat that goes out of the steam room and will not create a risk of excess condensate.

The lack of insulation in the simpleness in most bath buildings is more likely to be needed. This is due to the fact that the entire building is actively warming up the steam room and the washing need is warm at least other premises, but rather even more. The wake-up compartment is usually colder than we would like and warmly walking from the steam room just compensates for this disadvantage.

The partition between the washing and the steam in the bath is the optimal design.

The partition between the washing and the steam in the bath can be performed in several ways. The most common option is the manufacture of a wooden frame, in second place is a solid timber partition.

How to make a partition in the bath

The partition is a special design that dividing a common room into separate parts, such as rooms or compartments. At the same time, the materials of the manufacture of the main framework and its simpleness can differ significantly from each other. Competent bulkhead production involves preserving the main style of the structure.

Design partitions in the bath

Before making partitions in the bath, you need to determine the area of \u200b\u200bplanned premises. Their magnitudes depend on the dimensions of the construction and the number of permanent visitors. Based on this data, the plan is running the bulkhead to the existing walls of the bath with an indication of the axial sizes. Then the location of the doorways and the number of necessary material is determined.

Transformable designs - sliding, soft folding, rigid folding, retractable and screen.

The form of the planned partition depends on the requirements for it. If the bath's space is divided into the provision of reliable thermal and sound insulation of the premises, the durable stationary partition design is used. In other cases, it is possible to do with its mobile or collapsible options, for example, to separate the locker room from the bathroom combined with it.

Features of the brick partition in the bath

Advantages and disadvantages of brick partitions for a bath

Their advantages are due to excellent physical characteristics:

Brick partitions have good soundproof properties. The burden of bulkheads in the Pollipich have a "noise" insulation index equal to 47DB.

The disadvantages can be found:

The considerable weight of the septum: with its thickness in the Pollipich, the mass of 1 m 2 of the masonry is approximately 280 kg.

Device partitions made of brick in the bath

For the construction of such a partition, masonry is used in the Pollipich or Brick. Before starting work, it should be stock: sieve for sand, a container for the preparation of a solution, a shovel, a hammer, plumb, level and culma.

The workplace of work is exempt from unnecessary items, it is supplied with lighting and necessary materials.

If the brick partition located in the bath is to be plastered, you can not pay attention to the laying seams. But if it is a natural element of the design of the room, you need to perform a special tool laying with special care.

Features of the wooden partition in the bath

Pros and cons of wooden partitions for a bath

The advantages of such partitions are very significant:

The material of their manufacture is environmentally friendly.

Disadvantages are also available:

Designs made of wood are afraid of water, so they need waterproofing.

Read the Overview of the Complex Frame from Hemorrhogo Proconol
How to lose weight by 20 kg - Real reviews about Guarchibao

Wooden partition device in the bath

Consider the device of the wooden partition between the steam room and washing in the bath. Step-by-step process looks like this:

Assembly and fastening of the frame. This is the most time-consuming stage of work. The frame is used for the frame 50x50 mm or 50x100 mm, its assembly is performed on the spot. Two bars for the ceiling and floor with a length of each of them, corresponding to the width of the partition, are fixed on the corresponding structures using a dowel. Similarly, you should enroll with the walls for the walls. They are cut in the height of the room and are fixed between the floorboats and the ceiling in 600-120 mm increments. With the help of transverse bars is drawn up doorway. For stiffness, it is supplied additionally on both sides by intermediate racks.

Such a wooden partition in the bath can be installed in one day.

Features of the glass partition in the bath

Advantages and disadvantages of glass partitions

Modern glass partitions in the bath can be made of glass blocks - a kind of transparent "bricks" made of glass with a thickness of 6-10 mm. Their surface can be corrugated, smooth, matte, transparent and color.

Partitions look spectacular, durable, strong enough, fire-resistant.

Despite the outstanding advantages, the shortcomings of glass bulkheads also have a place to be:

The inner surface of partitions eliminates the gasket of any communications - electrical wiring, plumbing, etc.

Glass partition device in the bath

Installation of a glass partition for a novice - a difficult task. Cement-sand solutions with a shallow filler fraction or "liquid" nails are used for laying glass blocks. There are two ways to install: on adhesive cement mortar and in modular cells.

The base is cleaned of dust, garbage and dirt, and then aligned.

Work in the second way goes faster. Cellular lattices made of plastic, MDF or wood are attached to walls, ceiling and floor. Then they are filled with blocks using sealant or rubber gaskets.

The question of the bath partitions is quite extensive. We hope that the information provided in the article will help you choose the material and even make a partition in the bath with your own hands.

Partition in the bath do it yourself

The separation of the internal space of the bath construction is performed using partitions. We will tell you in this article about their species, features and devices. Content: Designing partitions in

Since the steam room and car wash perform completely different missions, how to make partitions in the bath, you should pay special attention.

First of all, you need to decide on the material from which the intermediate wall will be built, be it tree, brick or foam block.

The choice of material for the partition depends on what style the entire bathroom is made and which type of heating is used in it.

Wood partition

Wood partition in the bath

If the main material that was used in the construction of the bath is a tree, then the partition should be erected from it.

For the performance of this work, bars will be required, the thickness of the reach of five centimeters, with a cross section of at least 5x5 centimeters.

This will provide good insulation of moisture and heat, and not just a screen that closes visibility in the nearby room.

To make a wooden partition personally, you need to follow step by step instructions:

First of all, you need to carry out measurements and designate on the surface of the walls and the ceiling, with the help of smooth lines where the middle of the partition is located.
Then the main framework is made from BRUSEV. Connect wooden boards in the design, and attach them to the walls, better with spikes and drills. If this is not possible, the usual tapes for wood or nails that do not have hats are suitable. Between the bars you need to leave about eighty centimeters of free space.
Wooden boards are attached on the manufactured frame. For this purpose, the same materials are used as for the manufacture of a frame - self-tapping screw or nails without hats (another option - wooden lining).
The lining boards should be made on both sides of the frame. To ensure better heat and moisture isolation, you can fill out the empty space of the partition of the Minvata. Thanks to her, the pre-order will be a cool room, and the steam room will retain valuable heat.

To build partitions in the bath, it is better to use deciduous trees boards such as aspen or linden. Before use, they need to be treated with special means of antiseptic action.

The most important thing in the construction of a wooden partition is to properly assemble the framework. On how smooth and proportional frame frame, the sustainability and functionality of the entire structure depends.

So that the partition is more stable and durable, at the very beginning of its construction, you can make a small concrete threshold, a height reaching no more than fifteen centimeters, and twelve width. If you make a durable frame and reliably climb his boards, you can attach hangers on the partition and put towels, bathrobes and other things on them.

Brick partition

If you wish to make a brick partition, you can use a masonry of a whole material or a spoonful method of placement of blocks (0.5 bricks).

To the wall is not too heavy, you can use the hollow brick.

However, it must necessarily be resistant to high temperatures and high humidity.

Therefore, in the construction of the baths and partitions it is better to use red bricks in it, and not silicate.

About how to make partitions in the bath with your own hands, is explained in the next step-by-step instruction:

First, if the floor is covered with boards, they must be removed to reach the foundation. The whole surface on which the work will be carried out should be cleaned of extra things and is charged with a wet broom.
The room is prepared for work - good lighting is supplied, work tools are prepared.
There are marks of contours of partitions.
Solution is mixed. To do this, use the sieve, grinding machine, shovel and tank for the knead. Proportion of kneading - 3: 1 (for example, three sand buckets and one cement bucket). Water should be added until the mixture reaches sour creation consistency. In order to avoid premature solidification of the solution, it should be regularly stirred, but the water is no longer added.
A septum is erected using level, kirk, cells, plumbing and rules. To the wall turned out to be smooth, you should stretch the twine. First, two layers of the solution are applied to the floor, and then you can start laying out the brick. You need to start work from the wall. In order for the design to be more durable and firmly connected to the main walls, during the masonry you need to use metal strips Il-rods of reinforcement.
The second row should be started with half a brick. And the third one - from the whole, and so alternate them constantly.

In the case when the brick wall plays an integral role in maintaining the interior of the room, it should be laid neatly, always on time to remove the excess solution to prevent drying. But when the wall decoration will fully close the brick basis, then you can not be too worried about the appearance of the seams between the rows and separate blocks.

When the plaster layer is planned for the brick partition, it is possible to apply even the used brick, which will significantly save funds.

If there are doors in the partition, their frame should be installed before the brick laying starts.

Foam block septum

One of the generally accepted options for how to make partitions in the bath between the steam room and washing, is to lay it out of foam block.

Advantages of using foam blocks:

They have much smaller weight than bricks.
The foam blocks are made by large sizes, due to which the laying of walls with their use is moving very quickly.
This material has a sufficiently low cost.

Standard foam block sizes are equal to 30x60x30 centimeters. There are also other solutions for widths, heights and length of blocks, depending on what room is planned to be applied.

The process of creating a foam block is similar to a brickwork. But there are some differences in it. The process of work is as follows:

The surface of the floor and walls should be prepared in a similar way, as for brickwork. Then you need to stretch the cord by which the wall will be oriented, and outline the contours of the doorway.
The first row of blocks should first lay out in dry. So that the width was as needed in the bathroom, foam blocks can be poured using a grinder or hacksaw.
A special composition is used as a bonding solution for foam block masonry, which is divorced by instructions. To mix it with a building mixer.
On the surface of the block you need to apply about three millimeters of the adhesive mixture. After that, it is installed in his place in a row. For the strength of the partition, the second row should be started from a half-time block, and the third one is from the whole, and alternate them to the very top.
To stronger connect the partition with the main walls, you need to use fittings or large nails. They should be inserted into the holes in the wall (made in advance), lubricating the adhesive solution. The length of the valves should be at least five centimeters.
When the partition will be posted to the level of the upper crossbar of the door jambs, two arm of the reinforcement should be paved (in diameter of equal 1.6 centimeters). They must be more width of the opening at least ten centimeters. Then, on top of these metal add-ons, the following series of foam block is stacked, up to the ceiling itself.

Fucked by a foam block wall can be the same adhesive mixture that was used to connect rows. If there is such a need, you can create ways to install communications, such as electricity or plumbing.

When work with the plaster is completed, the partition must be dried, sharpen, paint, and cover with tiles, which will decorate the bath room and will make the stay in it as comfortable as possible.

If the septum is not constructed from a solid foam block, but from the half, then its weight will be small. In this case, it is possible to set the design on the wooden floor, without breaking the boards up to the foundation.

In order for the construction of partitions from foam blocks to be successful, it is desirable to take into account the following more valuable tips:

By purchasing foam blocks, you should pay special attention to their surface. If it is smooth and smooth, the finish will be faster and fulfilled better.
Calculation of block size depends entirely on the type of room in which they will be used. Construction of rebuilding in the bath is better to use lightweight and less wide blocks. It does not matter the density of this material.
The blocks that are obtained by cutting are considered better. This manufacturing technology is now more developed and progressive.
So that the masonry was more dense before starting it, it is better to moisten the water blocks.
So that the partition is durable and durable, it should not be solid vertical seams. To do this, in each new row, blocks or bricks should be shifted.
At the top of the design, between the last rear of the foam block and the ceiling, it is better to leave the opening, the width reaching ten centimeters. At the end of work, it should be closed using a mounting foam.

Finish partition stone

In many ways, the selection of the material for the partition depends on the heating method in the bath.

If it is a brick oven, then it must be supplemented with a wall of the same material.

If the bath is heated with an iron stove, then a wooden design is perfect.

But in this case, it is necessary to have it at a distance of more than ten centimeters from the heating center.

How to make partitions in a bath durable and beautiful: the best options and methods of their incarnation

There are several options for how to make partitions in the bath beautiful and durable. The technology of their facilities is quite simple, the main thing is to follow several

Partition in the bath between the steam and sink

Well, if when installing the box, all the rearrangements are immediately erected. But more often the room is divided after the roof is covered and windows and doors are inserted. The partition in the bath between the steam room and the sink performs a very important function, so the approach to its manufacture should be very thorough.

Selection of material

The partition can be made from almost any building material, which is capable of withstanding high temperatures, not highlighting harmful substances. It can be:

Frame design of wood. This option is perfectly suitable for both the bath assembled in the same way and for the brick structure. It is rawd enough and easier to be warm.
From the cut. The rebound of this kind is better planning and mounted during construction. This is important, because It is necessary to draw a dressing with the whole structure. After this, it is almost impossible.
From foam block and aerated concrete can be mounted in brick buildings, as well as wooden, when the foundation for the redesign was planned in advance.
From brick. For these purposes, it is better to use a red brick, which is refractory and retains heat well.
From glass. To do this, you will have to order a design for specific dimensions of the material resistant. This is the most spectacular option.

This type of partition is one of the best. Does not require additional care. There is also no need to perform insulation, because Wood is already in itself an excellent insulator.

When bookmarking the foundation, you need to provide an additional jumper on which the rearrangement will stand. If it is a pile or column foundation, the supports should be located under a partition every 1-1.5 m.
Breeds are preparing, which will correspond to the future wall. Length must be calculated taking into account the presence of a doorway.
The method of articulation with carrier walls will correspond to the one that is selected for the overall structure. If this is the connection "in the bowl", then the partition will be mounted in the same way.
The first crown is specifically short cut from the base to be more stable. After strengthening the groin crown, the mounting of the rebound begins immediately.

For this option, you will need a edged board. Its size should be equal to the width of the future rebound. It can be 200 × 100 mm, 200 × 150 mm, 150 × 100 mm, 100 × 50mm. The thicker will be the partition, the better the heat will be maintained. In order to calculate how much the material is needed, it is necessary to calculate the perimeter of the partition. Next, add so much supports as it should be necessary if they have to be placed in 60 cm increments.

If when bookmarking the foundation, the reference part for the inner wall was provided, then it is necessary to perform waterproofing before installation. For this, the dual layer of rubberoid or biket is stacked.
For a brick building, it is necessary to additionally make the threshold, which will prevent the flow of water from one room to another. The height of the threshold should be at least 10 cm. In order for it to be reliably intertwined, it is necessary to drill the holes with a diameter of 8 mm by its length and put the pieces of fittings in them. After setting the formwork and pour the solution.
Next, the lower board is stacked. It is mounted to the base with the help of a dowel. It is desirable to observe the horizontal plane. It can be determined by a building level or laser level.

It is better to store in advance with the number of necessary material. The masonry can be performed in the Pollipich. This will save, and also reduce the total weight of the entire design. It is desirable that the sand, which will be used for the preparation of the solution, was dry. This will help correctly calculate the ratio and will contribute to a good grasp.

The surface level is checked on which masonry will be carried out. With the help of a laser level, a line into two walls is projected and the distance to the floor is measured. If the difference is up to 10 mm, then it can be compensated by the suture thickening in some places of the first rows. With a larger drop, it will be necessary to align.
A wooden frame is installed on the form of a future door. It will serve as a guideline.

Foam block, Gasobeton

The relief from this material is built on the principle of brick, but there are nuances.

When buying, choose the material, the sides of which are as smooth as possible, so you facilitate the whole process yourself.
For the solution, it is better to use special glue, which is more plastic and dries faster. If you want to cook it yourself, then the proportions will be 4: 1, except for sand and cement there will also be a plasticizer and a foam supplement (they need 50 grams to one knee).
The first row is trying without glue. If one of the blocks need to be trimmed, it is better to cut two extremely sizes to the same size so that it turns out good gleaming.
In the same way, as in the previous case, there is a gleaming with carrying walls using fittings or metal plates.
Through two rows, a metal grid is stacked in the seam.
The doorway and the partition above it are planned in the same way as in the previous version.
Finishing finish is performed using a facing material or putty.

Now you know how to make a partition in the bath. There are no obstacles in order to try to build it yourself.

Partition in the bath between the steam room and washing - how to make a partition

Learn how to build a partition between the steam room and washing. Partition from brick, foam blocks, log cabin.

Bani construction with their own hands requires well-thought-out and verified actions. Extremely important is the partition in the bath between the steam room and washing.

For its construction, it is necessary to competently distribute the space in the bath and choose the right materials. In general, the construction procedure is simple, but it will be necessary to carefully follow the recommendations.

This article will consider the various types of partitions and materials that were used in their erection.

What is the partition

Partition can carry and decorative character, becoming a design element

Such a structure is extremely important for the bath. It has the following advantages:

attractive appearance;
high strength;
good level of sound insulation.

In addition, the partition will provide high temperature and comfort in the steam room.

If there is no need for high thermal insulation, you can build a more simplified building. Below can be seen a bath with a partition.

What is the partition built from? The choice of material is an extremely important stage of construction. The following options can be used:

wood;
brick;
concrete.

The brick partition in the bath is set if the metal furnace is mounted in it. For pairs, the optimal solution will be wooden structures.

Wooden bath partition

It is advisable to do in a wooden bath partition from a tree

Such buildings are erected from various types of wood. Their assembly is carried out by a frame-shield method.

Experts do not recommend building brick partitions in a wooden bath. Especially if the furnace is rarely carried out. Since the coefficient of thermal conductivity of the tree and the brick is greatly different, it will take a lot of time for heating the construction especially in the cold season.

Make a partition between the steam room and the sink is better from different materials. If similar material is applied, but with a smaller connection, it may be difficult to install connecting nodes.

The optimal solution for the construction of the internal partition in the bath will be a framework system.

Frame partition

The holes between the frames of the frame are filled with insulation

The frame partition in the bath is best suited for wooden buildings. To bring it, it will take the first thing to collect the frame from the dried wooden bars.

Their sizes are 50 by 50 mm. The hole between the bars is closed with heat insulator.

The following materials can be used as thermal insulation:

basalt cotton wool;
fluent plate.

Protect insulation from moisture with polyethylene layer

To protect the heat insulation layer from the penetration of moisture, it is covered with polyethylene film. Also, a good solution will be the covering of the waterproofing membrane, though its value is significantly higher than polyethylene.

Use stone decorative lining is extremely not recommended. Wooden construction inside the bath may need to be treated with an antiseptic. This will avoid the formation of mold and fungus on the walls.

Construction of a brick partition

Brick partition fitted with spoonful masonry

How to make partitions in a brick bath? Such material is quite common and is often used to build buildings in the bath.

The design is made with a spoonful masonry half of the brick.

To facilitate work, some experts use hollow material.

Preparatory procedures

Before switching to work, you need to carefully prepare the surface. Floor coverage is withdrawn to the base, after which the wet broom is cleaned. The location where the construction will be performed is equipped with good lighting. All foreign objects are made out of the premises and the contours of the construction are outlined.

To work, you will need to prepare the following tools:

level;
schlifmashinka;
trowel;
plumb and rule;
cement-sandy solution. For more information on the construction of the partition, see this video:

Creating a partition

The first row of bricks is placed on several layers of solution

The process of building a brick partition consists of the following steps:

The twine is stretched, which is used as a guideline. The solution is stacked and levels with cells. The level is checked horizontal. It will take to wait until the solution starts to push.
One more layer is applied over the frying mixture. After that, the first row of a brick screed is carried out.
A solution is smelled to the end of the first brick, after which it is carried out by adding it. It is closed and leveled according to the twine, the remains of the mixture will need to remove immediately until she has time to dry.
If the partition is planned for the door, it will be needed to pre-set it. With the help of the strut, the door frame is installed. The evenness of its location is checked and, if necessary, is adjusted for this parameter.
Laying bricks is performed close to the box. For a bunch of partitions, special metal strips are used to it, they are flex and attached to the side surfaces between bricks. Instead of strips you can also apply reinforcement rods.
After completing the laying of the first row, the brick is divided into 2 pieces of pickaxe. One half is used to start the second row. The twine, which served as a guideline, moves above, so that it is easy to navigate. The styling of the third row is carried out in the same way as the first. See this video in this video:

The masonry binding is an extremely important staging of the construction, which will evenly distribute the load on the design and significantly increase its strength.

The construction of any partition between the parillery and washing is a rather laborious procedure.

Not every newcomer will be able to fulfill such work independently.

But, as a result, this will ensure a high level of comfort in the bath, so recently the construction of such elements and has become popular.

Even in the smallest bath, there are usually two rooms: a pre-banker and a steam room, combined with a washing. But the question arises here: what partition should be between them? Wooden or brick? And how to build it correctly from the point of view of the heating of the premises?

In this regard, a home master may have a large number of questions that we will try to give an answer in this article.

What you need to know about partitions in the bath

Before the construction of a partition in the bath, you should take into account a number of features. In addition, for wooden and brick buildings there are various requirements.

About partitions in wooden baths

Wooden includes baths that are built from a bar, logs or collected on frame-panel technology.

Tip!
Experts do not recommend installation, especially if irregular building operation is planned.
The fact is that with the inner brick wall you will need more time to warm up the room, especially if we are talking about cold season.

The construction of the inner walls from the same material from which external, possibly, possibly, it was possible, but simply there is no need to be explained by several reasons:

There is no effect of atmospheric phenomena inside the premises, therefore, as thick and durable partitions here are nothing.
If you use smaller material here, it can lead to problems in connecting places.

Experts most often advise to equip the inner walls on the framework technology, since in the bath to make a partition on the principle of the frame is quite simple, and besides economically beneficial.

Frame walls possess the following advantages over the traditional logberon:

Price.
Little weight, and therefore, less load on the foundation, which extends the durability of the design.
Easy work.

At the same time, you get warm and durable interroom partitions.

We build a bathroom bathing wall

Consider how to make a septum in a tree bath.

For this, there is a simple instruction:

For the inner walls, we select boards, thick in about 5 cm and no more than 15 cm wide. Thinner boards may be a story.
We form a crate from the boards with a step equal to the width of the heat insulating mat.
Between the boards, we put the heat insulator. It is best to use mineral wool for this, as foam foam and is capable of separating harmful substances at elevated temperatures.
From above on a boardy frame, we press the waterproofer.
Such materials can be used as waterproofing:
- Normal polyethylene film. Material is taken, thickness from 150 to 20 microns.
- Special waterproofing material that has a foil side.
- Penofol, which represents, on which the foil is applied on one side. Thus, you create an additional layer of waterproofing.

Tip!
Mineral wool is afraid of water, so it is necessary to securely protect it with a waterproofing layer.
The bands are stacked by the mustache, cursing the construction scotch.

The last layer is mounted finishing material. Most often it is a lining that most corresponds to the interior and microclimate of bathrooms.
The furnace should be installed no closer than the meter from partitions.

Tip!
In the event that a metal furnace will be used in the bath, "you will need a brick partition, desirable, even from chammed blocks.
If the metal furnace is rushing directly into the steam room, the wall can be wooden, but it should be seen by non-flammable materials.

Partition in block bath

How to make partitions in a brick bath? Here specialists also recommend applying the same frame technology.

There are several reasons for this:

Brick walls are slower than heated, and accordingly, you will need additional heating costs, especially in winter.
Condensate is settled on a brick or block masonry, and it will need to take it somewhere.

Some professionals advise to use magnesite sheets instead of the board.

They are produced on the basis of perlite and cellulose fibers. They are fixed on vertical profiles, after which the installation is repeated, described above.

Tip!
Such partitions can be arranged without insulation.
Here the insulation function will perform airspace between the boards.

As a finish for such walls, it is best to use lining.

Naturally, in a brick bath, you can create a brick partition. In this case, it is best to use masonry in the Pollipich, additionally strengthening the design with steel wire every several rows.

Tip!
It is possible to erect a brick partition in a wooden house only when the final shrinkage will occur.

Conclusion

Bani construction is a very responsible process that requires a plan and should take into account a number of nuances. And since there are at least two rooms in the bathroom, the question of the right arrangement of partitions is very relevant. The information presented above will help you build an inner wall without allowing errors, and the video in this article will offer you to see the visual moments of this problem.

It will be about the skeleton partition in the bath from a log cabin, separating the pre-banker and the waters. The choice in favor of these premises is made so that you can show how to make a partition with your own hands between such, it would seem different in their functional accessories with bathrooms.

The wooden partition, which will be described in this article, is a wooden frame, insulated with mineral wool and clapped by cladding.

Considering that in the washing compartment, there is a warmed and reinforced concrete screed with a thickness of 150 mm, then a concrete border of 125 mm wide and a height of 100 mm was made to set the base of the frame. In addition, the concrete curb will allow to lay ceramic tiles along the partition, isolating the wooden wall overlooking the walls.

The concrete curb can be done both during the fill of the screed and in the process of mounting the partition, using homemade wooden formwork. For a better bundle of poured concrete with a floor, its surface should be treated with deep ground and a betokontact, for example, from Knauf.

Vertical frame racks and are made of planed bars: internal - 50x100 mm, and extreme and door opening - 60x100 mm. Horizontal binding bars (upper and lower) have a cross section 60x100 mm. All jumpers are made of 50x100 mm bar.

The base of the base to the concrete curb is made using an anchors of 16 mm. The extreme racks are installed in the grooves in and are fixed to it 8x90 mm hexagon screws. In order for the frame to keep the cut from the cutter, oval longitudinal grooves are made in the racks. This will give screws to slide together with the wall and do not create an excessive stress on the frame, and with it to the entire partition.

The upper binder bar does not reach the ceiling by 30 mm. This gap is used to compensate for precipitation or expanding a cut as a result of atmospheric phenomena and seasons change. The groove in the wall is cut on the entire height, ranging from the floor in the pre-banker and ending the ceiling.

As a heater, a mineral (basalt) cotton wool is 100 mm thick, such as Rockwool. Some framework cells have dimensions of 600x1200 mm, which corresponds to the standard size of the manufactured wool. The wool closes and fixes the stapler on both sides of the frame of a polyethylene film, which prevents moisture penetration inside the wool, thereby preserving all its heat-insulating sound-absorbing properties.

The eurvagon mount is made by kleimers on the crate of 25x50 mm planks. The cheek itself is mounted on top of the polyethylene film and is attached to the frame of the wood self-assembly. The direction of laying the lining - from the corner of the septum by the method of "spike in the groove", and not vice versa. From the side of the pre-banner, the lower line of the crate is additionally fixed to the floor, and in the washing department - put on a concrete border and is attached only to vertical frame racks.

The final finish of the partition is made after installing the door frame. First, plinths are installed, which one end begins in the walls of the wall. The edges of the septal board (platband) are then closed, which are also reached in the same grooves.

The upper platband is attached directly to the ceiling with the condition that it will move freely with it in the process of cutting a log, without affecting the partition itself. The gap between the ceiling and the riding partition is closed by cotton or other thermal insulation material.

Compounds of wooden elements are made using galvanized wood screws. Open details are also attached with self-draws. So that the screws are not visible, it is possible to pre-drill a stepped hole, and after screwing the self-pressing of the same diameter after screwing the screw (pin).

From the side of the waters, the wall is frozen by ceramic tiles, and then the cladding is put on it. To the bottom of Vogonki along the entire partition to the frame racks, a plank (plinth) is fixed, which closes both the lining and part of the tile.

The order of works on the construction of the frame partition with their own hands

Perhaps I did not cost me so detailed to describe the structure of the wooden partition, and start immediately from the order of work on its installation. However, what is done, you will not return. And to whom it will not be interesting, he can immediately go to this section of the article, taking advantage of it.

Preparation of concrete base and log walls

Montage of wooden partition frame

Note: At this stage of work, you need to pay special attention to the accuracy of the framework of the frame frame, as it will affect the quality of the entire inner wall. Vertical, horizontal, flatness, dimensions - all this will affect how our partition will turn out.

Warming and installation of crates on the frame

Note: The film can be placed under the base of the frame already at the stage of its installation. Then the question of fixing it at the bottom will be immediately resolved.

Installation of the door frame in the opening of the partition

Facing with ceramic tiles in the oil compartment

This operation can be performed both before weaving with clapboard and after it. The main thing is that the seat of the trampling and end of the ceramic tile was made accurately and without gaps. As for laying tiles to the floor, it can be done at any time.

Clapboard clapboard

You need to start from the corner itself. Cathrootting is triggered by the method of "spike in the groove". That is, the last fixed element must have an open groove. Each subsequent element is inserted with a spike in the groove of the previously attached lining, and with the help of metal kleimers (fastening brackets) is fixed to the crate. The last lining is cut under the desired size and is fixed by screw screws. In detail how to mount the lining, you can see.

Installation of platbands, plinths and sealing edges partition

Finally

This design of the wooden partition design is designed for a shrue of a bath that has surrendered the time and gave full sediment. The compensation gap (30 mm) between the partition and the ceiling is calculated only on the change in the sizes of the cut under the influence of atmospheric influences and weather conditions.

If there is a need to build a partition in the bath until the cut is completely sediment, then this gap should be increased to 60-80 mm.

On the side of the washing branch, the framework of the frame can be made from waterproof drywall. In this case, the wooden crate should be replaced with a metal profile. This partition can be easily bled with ceramic tiles and easy to equip there.

It should be remembered that the carved grooves in log walls reduce their strength. Moreover, the deeper and wider the grooves, the less the strength of the wall. To protect the logs from rolling (deformation), it is necessary at the stage of the construction of the walls to bind the logs in the place of the proposed partition with wooden brazers, as a rule, with a diameter of 30 mm. How to do this, you can read in the article about.

Go to main article content: Sergey

It was completed, it's time to think about the separation of the internal space into separate rooms. The total Siruba Srub is 6x4 m, so I turned on the required minimum pair, washing and tambour. Tambour was drizzled back in the construction process. It remained to decide how to separate the steam room and washing. Washed the mass of literature, came to the conclusion that it is easiest to make such a partition on the framework technology. First, it is built very simple and quickly, I managed for 3 days. Secondly, the price came almost a penny. Thirdly, (very important!) The frame is lightweight and practically does not load the foundation. I will describe how construction was carried out.

Step 1. Assembling and mounting frame

The most time consuming part of the work is to assemble the frame from the bars of 50x50 mm. I decided to collect it immediately in place. Initially, the lags of the floor were pinned the lower bar (lower strapping), extreme racks were attached to it and the walls. The top bar is laid on top and secured.

Installing a framework of a barrack

I want to note that only 4 months passed from the construction of a cut before editing the partition, the shrinkage still continues. Therefore, between the upper strapping and the ceiling, I left a 2 cm gap - to compensate for shrinking shub shrink deformations. The clearance filled with jute felt. All this is done based on the fact that when the log house will sit down, the ceiling level will decrease and will be installed just on the upper cutting of the partition.

For greater rigidity in the locations of the side racks and the strapping, metal corners are screwed.

With a step of 600 mm, the racks are installed, the opening is made for the door block and the brick screen of the furnace. It is important to note that the furnace is planned to be dried out of the washing, so its frontal part with a brick shield must be mounted in a partition.

All the slots between the walls, the brick shield and the bars of the frame are filled with jute felt.

Step 2. Warming Partition

I decided to embody the internal filling in such a scheme:

Scheme of internal filling and siding frame partition

As a insulation, I used basalt wool "Technobock Standard" (TechnoNIKOL) - in the form of plates with a thickness of 50 mm. At the manufacturer's applications, this material must withstand the heating to 400 ° C, not to burn and not melted. Also, basalt wool is not hygroscopic, suitable for wet rooms. Even if the moisture drop falls into the partition (despite the vapor barrier), the inside will not start rot. Well, it is important that basalt wool is absolutely safe for health, it does not release anything when heated.

Watches width - 600 mm, when installed between the racks, it was necessary to compress them a bit. To cut the plates (if necessary, the installation of parts, for example, above the shield, above the doorway) was used a sharp knife.

Basalt Wool Plates Between Partition Racks Partition

Step 3. Waste Foil insulation (from the steam room)

From the side of the parley, the insulation was covered with a foil in 2 layers. I consider foil with the best vaporizoator for the wage. First, does not miss steam and drip moisture. Secondly, increases the thermal insulation properties of the partition (or walls), as it reflects infrared radiation.

The foil bought by me was thin, so I decided to lay it in 2 layers. Initially, the first layer was shot with the sickling of the seams with foil scotch. The mount was carried out with the help of a construction stapler, on the frame racks. From above, in disintegration with the first layer (so that the seams do not coincide), laid the second layer. Suts, holes from the stapler, the corners are also punctured by scotch.

When I discarded Foil, then pulled it on the frame, in some places it thinned, began to wrinkle. There was no hole, but, for your own calm, these damaged areas I also stuck with scotch.

Insulation of the Heater Foil (vaporizoation) from the steam

The joints between the brick shield and the foil are passed with heat-resistant silicone sealant (anti-Greybkov). Such such sealant quickly, combines diverse surfaces well.

Step 4. Waterproofing (Waterproof)

From the side of the washer foil, you can do without waterproofing. To do this, I bought a roll of the vapor-permeable membrane "Izosan A". On the one hand, it will not allow a splash of water splash in the insulation, and on the other, it will allow the insides of the partition "Breathe", ventilated.

The sheets of "Isyospan A" I fixed the brass, to the frame racks. The seams and holes from the stapler overlap scotch tape.

Fastening sheets of waterproofing "Izosan A"

Step 5. Fastening the wall paneling (from the side of the washing)

The lining clapper was carried out from the side of the washing. Here I was waiting for the meditation. A neighbor argued that the Ventzor between the vaporizolator and the clapboard is a useless thing that occupies a place and is completely not affected by anything. At the same time, the familiar builder proved the opposite. It seems like the gap allows condensate if it is formed, flipping over vapor barrier and not absorbed into the lining. I thought that this opinion was more common and the gap did. Although, not fully confident in its necessity.

For the organization of the gap on the frame racks, rails are stuffed. Their thickness is the size of the gap. I used the rails of 15 mm, stuck them on the racks using conventional thin nails.

On top of the rails she saw a pine clapboard. To protect against moisture and giving the color, the antiseptic composition of the Supi Saunasuoja (Tikkurila) in 2 layers was passed. The tree is perfectly kernel, the color turned out to be smooth, beautiful. It was an unpleasant smell from the antiseptic, after 3 days it would completely weathered.

Covering partition wallboard is performed on thin rails

Step 6. Fastening the board (by steam room)

The partition from the pair, I decided to sheathe not with a clapboard, and a 35 mm thick board. This board - used, once lay on the floor in the house. Now the floors are replaced, and the board is still in suitable condition. Although the species has already been isolated, spammed, acquired stains. To give a blackboard a new life, I carefully squeezed her grinding machine. Half an hour and top layer removed! The board turned out almost like new.

Again, a centzorzor was formed, this time a thickness of 20 mm. The rails for it were used with a cross section of 40x20 mm. Reiki I nailed to the frames of the frame, on top of them - boards. All attachments were performed on nails.

At the end of the trim, the surface of the boards was covered with Supi Saunasuoja (Tikkurila). He dries the antiseptic quickly, in the day painted the partition in 2 layers.

I plan in the future on the bottom of the inner walls of the cut and partitions to launch a tile cladding with a height in 1 tile. This will prevent the rotation of the lower crown of the cut and partitions that are in wet steam and washer.

This looks like a frame partition in a bathroom!

I made such a partition in the bath. Quick, inexpensive and without helpers. Already managed and get into the steam room to evaluate the quality of the fence. What do I want to say? The thermal insulation qualities of the design are excellent, for 2 hours the bath warms up completely. Due to the removal of the panel in the washing time during the protood, and washing and washing. There is no condensate on the partition, the painting makeup does not change its color.

The frame partition is good what can be easily installed in any bath. Although in a litter, at least in a brick or gas-silicate structure. This design is universal, and its filling can be changed depending on the purpose.