Table of plywood: basic rules of work with the material, the manufacture of the simplest structures and tables for work. The table from plywood with their own hands is simple and beautiful how to make a tabletop do it yourself: the scheme and the assembly process

A similar table can be very useful in shortage of storage location and if you are working with a tree not every day and on occasion.

Step 1: Sizes and Identification of Parts

Many details have only one dimension. This is because the second or unimportant, declared to another place, or, depending on the thickness of plywood. I learned this way: 18mm, 23/32, in 3/4 may be close, but small errors add up.

You will need:

4x8 sheet of plywood. I used BC. e. And he was marked 18mm.

4 pipes about 32 "long. This is a flexible item. I used 1.25 inch aluminum tubes from Onlinemetals.com. They are expensive with delivery, but they were needed, as I drilled holes that were too large for my 1 "electric pipe. I plan to experiment here with what you have in stock and which drills you have access. Tight fit will give the best results.

8pcs x 2 3/8 "bolt

Barish nut 3/8 8pc

3/8 16pcs washer

glue & Double Stick Ribbon Carpet

cookies and or rifts of drywall

3/4 oak dubel 36 "Long

Notes:

Blue pieces and one short yellow tube support supports. They are shown here, but installed under the table to keep the pipes parallel to the top.

Not all photos are 100% accurate. The first table was a failure and some adjustments were made to final drawings.

Bolts are busting, but more easier to use.

Step 2: Cut sequences

The idea here is to have similar parts without moving the saw. Desktop a circular saw can be used, but it was done with a circular saw and parallel emphasisWhat came with him.

First segment: Rip 24 "Off Short end 4x8 plywood. This is for the top of the table and will be the basis for many other aspects. It is important to use some of the cut. Track saw a straight edge, etc.

Second segment: From the other end to use your 24 "piece and subtracting 4 plywood thicknesses. It should be about 21. Cause It is important because the legs are placed on the inside of the top of the table and outside the shelf.

Cutting them to remove any side gives greater accuracy.

Set of these two to the side and continue cutting.

Slices have a color label, and if they have a color or color point they are one general dimension. Remember, save on the right side of your line.

Note Feet: Feet should be 3 "x3" when finished. This section of the sheet has a short side of the measured long for a rabbit. If you want glue and screw or glue and biscuits to the short side, 2-1 / 4, or 3 "minus plywood thickness!

As soon as all strips cut back to the first 24 "wide piece made and cut, that 37" long. We cut carefully, with a guide or straight the edge of some. Save cut off for then how the short skirt ends comes out of it.

Next segment Shelf on top length. This was done using the second segment. Use the top you just done as a template and subtract four plywood thicknesses. There must be about 34. " Save sliced \u200b\u200bas a short skirt ends will be made of this.

Step 3: Drilling holes, long boards

1. Take two long 3-3 / 4. To get the length spread them on top and subtract two plywood thicknesses. Spend a line. Clamp them together and cut at the same time if you can with circular saw or miter saw. Come down to the side.

2. Cut two short 4-1 / 2 and the remaining 3-3 / 4. This aspect should be 32-3 / 8 "+/- so that they will fit into the shelf when everything is collected. Clamp and cut all three immediately.

3. Next drill holes the desired diameter Depending on which pipes you have chosen. Pay attention to the location of the Link from the bottom. Mark all the "bottoms" for subsequent installation. Drill holes as much as possible. To do this, I used double tape and drilling machine. All pieces were folded on a flat surface with a reference to the side. In short, they were in the center and all accommodate.

If you do not have a boring machine, drill three 3-3 / 4 wide as one group, I remember in the center shorter and make your labels for longer. They must be ordered long, short, long. Then, with the help of a shorter quality template, drill two 4-1 / 2 in width. I would advise it all the same using double-sided adhesive tape.

Also pay attention. If your plywood has a good side / and a bad side, which is important for you, flip board is properly. If the holes are not perfect pipes may not allow you to do it later.

Step 4: Drilling holes, short boards

1. The board supports. Cut the remaining 4-1 / 2 boards approximately 24 ". I did it by cutting 4-1 / 2 x 48 half. Then add the remaining 4-1 / 2 and cut all three immediately to the trader saw to maximum length possibly.

2. Pipe supports. Reducing the long 3-3 / 4 in the amount of two pieces 22-3 / 8 +/-. They are suitable for the table so that their actual size is 24 "minus plywood thickness * 2.

Similar to long boards These must be laid and merged. Ideally 4-1 / 2, 4-1 / 2, 3-3 / 4, 3-3 / 4, 4-1 / 2 from 3-3 / 4 in the center. Remember the bottom mark. If you need to break, that I would like to make 3-3 / 4 and 4-1 / 2 and mark them as A. Do everything else and mark them like B. You do not want to be bending the pipe to get things to fit.

Pay attention to the holes:

My first holes were for 1 "EMT conductor. This material was cheap, but my hole was too sloppy. Thus, dear aluminum. However, 1.25 aluminum after 1-1 / 4 hole drilled with the Fostner bit was too dense. It ended using the first drill and some sanding.

Step 5: Optional Orange

In my table I am Mortised Foot Place. I do not think it is absolutely necessary, but it really adds to stability. This is a fair amount of work. Take it or leave it, worse the case add a few more bolts!

If you decide it should be done before the bottom of the table. Ideally, before you make holes and demonstratively before the skirt is added.

Step 6: Collect top

It should go pretty quickly. I used the biscuit of Fuganok. If you do this, do not forget to mark the boards and links to right corners. Glue and clamp or glue and nails / screws to work as well.

All your pieces had a stigma on the bottom. Make sure it can be seen when you collect these pieces.

Step 7: Drill in the top

Two ways to do it.

1. Spend a line 2-1 / 2 throughout the perimeter of the upper part. From this line of the centers of holes 4-3 / 4 from each other in the direction of the short and 5-5 / 16 in far Destinations. Drill away. Figures a little off, 1/8 maybe. With some bizarre geometry, you could leave the strings if you really want. 3/4 "Fostner Bit to achieve the best results

2. I built jig. 9-3 / 4 x 37 plywood trim. Spend a line 2-1 / 2, the opposite is normal. Mark your centers 5-5 / 16. On the drilling machine to set a link 2-1 / 2. Drill of one hole line and only opposite two angles.

Put the template on your top with the line of holes at the bottom edge, the clamp is reliable. Drill. Then turn it over and align the two angular holes on the template from two detailed. Stick 3/4 inch dowel in each of the two angular holes. Clamp and drill on line again. Next revealed fishing rods, slide the template of one line, putting in the corners.

It worked pretty good. Holes looked good, but not 90 degrees. This is probably needed another jig!

Step 8: Legs

A couple of ways to make legs.

Cut all the legs up to 32. This is not critical. If you have other machines, you can use in combination with this table I think that changes that. Cut as much as you can safely immediately for greater accuracy. Make sure you do not use more than 3 " wide boards. Those who are on the shelf.

We are 3 "strips or 2-1 / 4" or 2-1 / 2 ". In accordance with these plans 2-1 / 2, since there were rabbit and Dado. If you want to use other methods, use 2-1 / 4 ". Or technically 3 "minus plywood thickness. In my case, 18mm.

Step 9: Collect the shelves

We cut earlier. It should be about 34 "(37" minus 4 plywood thickness).

We take the remaining 3 long "wide boards. Spread them on the shelf from above and put two pieces of plywood at the end to shorten the total length. Scribe and sv. Cut them both at the same time. There must be about 32-1 / 2. "

Collect the shelf just as you did the top. No need to apply additional holes or spikes.

Additionally:

Tapes Long boards together and drill two more holes for pipes. I am in the center of the mine at 3 "Board and about 4" from the end. I did it much however, it would be more utility, if several wells are set to raise and lower the shelf. I have only one shelf with a height.

Step 10: Leg Hole cutting guide and foot hole

This reference book of holes in the upper and in the shelf is accurate. This is not necessarily, but if you are turned off in all holes, then the legs will be determined specifically. It helps make legs interchangeable.

Step 11: Shutters

Without a table, no family will no longer be. Moreover, there are several tables even in the smallest cell of society. At least two: kitchen, which can be used as a table, and working - he is written. And if there is a child in the family, you will still need a table for its occupation. Yes, and the bedside or magazine will not be superfluous. The whole problem is that the number of furniture elements offered by manufacturers sharply contrasts with their quality. Plus - it does not always have the opportunity to find what will have to taste. In such a situation, the table from plywood can be optimal output from the position.

Table from plywood make easy

The table has plywood whole line Qualities that make it very seductive in the eyes of potential owners.

Initially, plywood was invented to compensate for certain flaws of wood. And the inventors managed to solve this problem: plywood is formed in such a way that each subsequent layer of material levels the weaknesses of the previous one. As a result: The same table from plywood is pretty wear-resistant and durable.
Compared with any other plywood materials - extremely cheap Material. Of course, it will not be able to withstand hard loads, but if they are not expected (not necessarily, on the table from plywood to chop, for example, meat), then the tabletop from this material can be a real decoration of the furnishing of the appropriate appointment.
But the main advantage of the material is the ability to create a table of plywood with your own hands. Plywood is easily cut, processed by the most primitive tools, does not rsch - and this is its main advantage in comparison with the billets of solid wood. So you can full power Include flight of fantasies and create unique furniture samples with the sophisticated abis.
No less attractive flexibility of plywood: it bends without the formation of cracks and deformations. Of course, for the main elements of any kind of table, this is not fundamental quality. But it allows non-standard to issue a ready-made furnishings.

The table from plywood is desirable to make not made from boxes left from packaging material for large-sized equipment. The optimal raw material is Mark sh2 - it has two-way treatment, that is ready product It will not need to end the final refinement. But if the table is supposed to be used in excessive humidity - for example, you plan to replace the tabletop in the kitchen - it is better to choose a material with moisture-resistant coating.

Required toolkit

Every business begins with the selection of tools that will allow an intended ventilation. Whatever the table from plywood you have planned, and even if you only need a tabletop from this material, you will probably need:

lobzik (its electrically option is preferable);
screwdriver; more convenient to operate and modern screwdriver;
fasteners In the role of clamps most comfortable screws;
glue most suitable for fastening parts from plywood;
measuring instruments (at least - a construction kit and roulette);
grinding accessories;
drill.

Pencil and actually the material for the table is intended by default. In addition, there will be no extra furniture plugs that will allow disguise the locations of the compounds of individual elements.

The main thing is accuracy and accuracy

The simplest table of plywood

You can practice on the similarity of the working version of the table. It consists of only 4 elements:

countertops;
two backpoints that perform the functions of four legs in the classic design of the writing table;
the struts, placed by the online rust of the supports from the back side of the table top.

The dimensions of individual parts are defined individually, depending on personal needs. Drawing up a preliminary drawing with an indication of the exact parameters.

The manufacture of the table can be reduced to the following manipulations.

Marking on a sheet of plywood of the proposed desk element.
Cutting blanks according to markup.
Treatment of cutting edges with grinding or sandpaper. In the latter case, it should be started with the use of coarse-agile sandbreak, gradually moving to work with small grain paper.
Pencil mark with the help of roulette places of screwing screws.
Drilling holes for fasteners. Note that the diameter of the drill is selected slightly smaller than the diameter of the screws. Then the sheets of plywood do not burst when assembling.
Razzing: The top of the holes is processed by a drill with a large diameter so that they can be dried with screws of the screws.
Assembly. First, countertop and side racks are docked. After aligning the elements relative to each other, the back cover of the product is installed.

The penultimate step will be putting on the hats of the screws of the plugs. Alternatively, these defects can be sharpened and paint plywood into tone.

You can get furniture of any style.

To increase product strength

If the table is intended for installation in the kitchen, or for the use of a teenager, it is better to take care in advance that the product is as resistant to physical exposure. To do this, all the docking seams make sense before fastening to melt glue, and from the inside the angles to strengthen with metal furniture struts.

The final finish of the table affects the general impression

Final Stage

Perhaps on the tabletop will have to walk emery paper: plywood does not always have smooth surface. If you make the kitchen table and purchased a material that is not characterized by increased moisture resistance, you may need impregnation with the corresponding composition. In this case, it will take time to wait for the complete drying of the impregnation.

For the final finishes are suitable:

lacquer not emitting harmful evaporation;
paint that corresponds to the same condition;
film-self-playing, imitating the structure of the tree or stone.

We would recommend lacquer. Plywood has a fairly pronounced wood pattern, which will fit in almost any interior, be it a living room, children's or kitchen. And most importantly - varnish will not be derained (unlike the film) under the influence of temperature differences. If the bubbles appear, they can be seated without any problems and open the surface with a new layer of varnish.

To apply a varnish, it is better to choose a room with good ventilation and a temperature that does not go beyond the range of 19-20 degrees Celsius, where to transfer the table. Tassel for varnishing should be with a natural pile, in which the tips are cleaved - it allows you to carry out enough long strokes without visible traces after drying.

The method of covering the lacquer of the table is such.

Varnish is divorced. Usually, the White Spirit is used to dilute it, and the proportion is withstanding 1: 1, but this item should be clarified in the instructions attached to the composition. It is very simple to do this: the solvent is gradually poured into a varnish with continuous and slow stirring.
The first layer is applied along the fiber plywood. It is not necessary to push the brush much, keep it under a small angle relative to the surface.
After about a day, when the first layer of varnish is well frown, it is necessary to remove the pulley connected on the surface (if any). For this use fine-grained sandpaper. After processing, the countertop and the remaining parts of the table are wiped with a wet whit-spirited by the wind, without push.
For the second layer, a varnish is used, diluted with solvent in proportion 3: 1. After drying, another grinding is carried out using the fine-grained emery paper.

If you want to achieve the perfect result at all, you can cover the tabletop 2-3 layers of undiluted varnish and walk on it not only the most delicate sandpaper, but also the felt circle. With this processing, even the easiest table begins to remind the work of furniture art.

Polishing is never superfluous

Information for thinking

The table from plywood is not as simple as it seems. It is quite possible to build a transformer table that will save the space of your apartment. Moreover, the techniques will remain the same, only will have to work on the drawings of the structure and stock elements of the mechanisms that will translate furniture from one state to another.

For the living room you can build or a guest table, or a coffee table on the principle patchwork. Types of plywood, like breeds whole treehave visual differences. So, buying trimming material made of miscellaneous woodYou can recreate a real puzzle in the table top, fascinating all who drink tea with you. True, the cutting of plywood will be needed truly jewelry. But in such conditions, to make the tabletop itself or a full-fledged table from plywood even more interesting.

How to make a table from plywood, you can see the video:

Examples of plywood tables

Any master. The only material for the table is plywood, as a result we will get a simple beautiful and most importantly functional coffee table that will decorate any interior.

Dimensions of the table IN-490 mm, Sh700 mm, G-500 mm.

Now let's start everything in order.

Materials and tools

For the manufacture of such a table we will need

plywood thickness 10 mm;
electrolovka or manual (school);
pVA glue;
sandpaper;
paint or varnish your choice.

Production of table

I did not do the table, but only developed the model in the Compass-3D program, so you will see the end result only after you collect the table in one.

I give all the necessary drawings with dimensions and all the necessary data for creating such a coffee table.
For such a table, we need only 1 m2 of plywood with a thickness of 10 mm.

To begin with, you need to transfer all the sizes with the drawings on Faneru, of course it is not the most fast waybut no less effective. Naturally such a way is more time-consuming, but it will take a minimum of tools for its implementation, just a pencil, a square and a ruler.

Drawings for transfer to Phaneur

For the happy possessors of printers, there is a simpler version of the size of the sizes on the paneur. You need to print all the necessary drawings, and glue them to the plywood, after which everything is cut along the contour contour. In order to print all drawings, you need to install the COMPASS-3D software on your PC, and it is possible to print it with it. The process of installing the program and printing is described in my previous article, you can see.

You can print all the details on one sheet.

Drawing of the coffee table

File downloading:

Coffee table drawing from plywood.frw

Attention!

Top Couple

You can print the table cover separately.

File for download

Top cover. FRW.

Attention! Hidden text will be available after registering or authorization on the site.

Regiment of the coffee table

Print the shelf separately.

File for download

Shelf.frw.

Attention! Hidden text will be available after registering or authorization on the site.

Coffee table legs

Feet Print separately - 4 copies

file for download

Feet.frw

Attention! Hidden text will be available after registering or authorization on the site.

And of course there is the easiest way to get the necessary prepared parts for the assembly of the table - it is cutting parts using a CNC machine. All who has the opportunity to do this with the help of a CNC machine, ready-made items will receive in minutes.

It is not dependent on which of the ways of cutting parts you have chosen, at the milestone ultimately have the workpiece we need. Now you can safely hang all the details of the sandpaper and you can begin to glue the table. Before gluing I recommend collecting a table without glue, in order to check if everything is suitable, and most importantly determine the assembly oddness of all parts. All joints are well riveted with PVA glue, or any other glue that is designed to glue the tree.

After gluing and drying, it is necessary to remove the extra glue on the joints, and go to those places with sandpaper. Now our table is ready to paint. Here the choice of paint, varnish and their colors remains yours.

This simple, durable, lightweight and elegant coffee table can be made in a couple of evenings in a home workshop with a minimum tool.

The shelf in the table is just provided for newspapers and magazines. Also, a table can be used as a dining, putting it in the room, or flipping your favorite magazines with a cup of coffee at the table in the evening. I think here everyone will choose the scope of such a table for itself.

Thank you all for your attention, successful to you

Homemade furniture now in big Mode.. She has a lot of advantages over the factory - house master It certainly knows exactly what he did his cabinets and chairs, and usually tries that his creations not only adorn the interior, but also served long enough. If you decide to do it and you have some materials after repair, you can first try to make a table from plywood with your own hands. Some models will be discussed in our article.

What would you like?

Plywood is an excellent material from which in principle you can make any furniture, and it is even more suitable for the table than the most popular chipboard. But before making a table from plywood, think what your product should be:

compact;
comfortable;
beautiful.

Otherwise, it just makes no sense to take a job. In stores you will find a lot of diverse tables from the most unexpected materials. Among them will probably have tables from plywood. There are a lot of options that can be made with your own hands:

magazine;
children;
writing;
kitchen;
table-workbench;
any other model, right up to the secretaries and models combined with cabinets.

Much depends on what exactly forced you to take the case. Do you want to seriously make the manufacture of furniture, fully furnish your apartment or have you just left the pieces of plywood that you need to apply somewhere? But in any case, to start better with something small.

Important! The first table of plywood can be magazine - it will take remnants of what you used during repair. By the way, not necessarily plywood - maybe laminate and chipboard.

Coffee table

To make a small table of plywood with your own hands, the drawings are not required, but the template is very useful. The table, which is described on, is attached to the wall.

Important! Your future product can be of different heights, in this case it is not necessary to comply with sanitary standards that prescribe how to sit at the table and how legs should stand. It is a magazine, there is some statuette and a table lamp.

Peel into the covers and see if you have:

a piece of plywood for countertops;
small, but a whole sheet of plywood or thick cardboard - it is needed for the template;
carpentry or other moisture resistant glue;
electrolovik;
a circular saw;
pencil;
vice;
grinding machine (you can easily do the sandpaper, but it will take more time);
fasteners;
wallpaper remnants, watman sheet or millimeter;
long line;
varnish, wax or oil.

We collect legs and prepare details

We begin the manufacture of table with sketch:

Come up with the form of the tabletop - it can be rectangular, square, round, oval, with a notch or in general bizarre.
Come up with the shape of the legs - you can make them straight or curved.
Draw it all on a piece of paper.
Start the sizes. The table is small, so the main parameter to which you want to navigate is the size of the plywood sheet, if, of course, you do not plan to make a set tabletop from pieces.
Draw on big sheet Full-length legs.
Transfer the drawing to a dense cardboard.
Cut the legs on the template - if the form is complex, you can use not electrical, but the usual manual Lobzik.
If the plywood is not fat, make two-layer legs.
Spread the layers.
Remove the excess glue and give the billets to dry.
Put the legs on a flat surface.
Align them by template.

Important! At the model that is attached to the wall, the legs are only two.

Table top

If the countertop is simple and made from a solid piece, there are no problems. It is just cut out. Other thing if you only have plywood pieces or if you want to make a typical pattern from different species Woods. In this case, the fragments are cut at an angle so that a smooth surface can be made up and the seams were not visible. First you need to glue pieces into a single whole, and only then cut the table top by the template. After the workpieces appear, we do the following:

I am minimize the surfaces of the legs and countertops - get rid of the heads, sharp corners, etc.
On the bottom side of the countertop we plan space for self-tales.
We screw the legs using furniture corners.
On the wall we plan a flat line for fasteners.
Fix the table to corners or on a metal profile.

Important! Corners must be attached to the bottom under the tabletop so that they are not visible outside.

What fane choose?

A table of plywood does not necessarily be attached to the wall. Can be done very normal table, on one or four legs. And he can be much more size. But in such cases, the remnants of the materials are not separated, the Phaneur must be selected specifically, and the question arises, which one.

Important! Plywood is a glued veneer, and the number of layers is always odd, and most often - divided by 3.

The benefits of this material are enough, and the main of them are strength and resistance to abrasion. They are due to the location of the fibers. For the manufacture of plywood apply:

birch;
coniferous species of trees.

Important! There are also types when the veneer is made of birch, and the inner layers are from coniferous trees. This is a fairly cheap variety. There is a material that is fully made of deciduous treesBut it costs more.

On the price tags in the store you can meet some not quite understandable designations:

brand;
grade;
grinding.

Mark.

Mark indicates such qualities of plywood as:

resistance to moisture;
application area.

You can meet such designations:

This is what you need to remember:

FC means that glue from carbamide resins was used, such a brand is used for furniture and internal work indoors.
For external work, FSF is used - this is a moisture-proof material, but the composition includes formaldehyde, this option is not suitable for furniture.
For plywood FQM, melamine resins are used, which makes it possible to apply the material for all works.
FBA means that plywood to moisture is unstable, it can be used for furniture for the living room, but it is not suitable for the kitchen and bathroom.
Excellent option - FOF. Plywood is covered with a protective film. It is expensive, but high-quality, moreover, the film can be color.

Variety

This indicator is determined by the appearance of the surface. It is indicated by the letter E - it higher quality. Next, lower coefficients are followed, they are designated by Roman numbers from I to IV or ordinary Arabic. In this case, the same sheet can be two varieties - separately for the face and inside.

Grinding

Unlightened material is denoted as NSh. There may be other options:

Sh1 - one side is polished;
S2 - Sheet is polished on both sides.

Important! On some sheets, you can see the letter F with different indices - the amount of formaldehyde is denoted.

Some basic principles of work with plywood

Before making a table from plywood with your own hands, as well as any other furniture, try to master the main principles of working with this material. It concerns tools. It is better to use an electrolovka, and for some particularly thin works - a manual jigsaw. Any of them allows you to make high-quality sections, and not necessarily straight. Putting the jigsaw - a separate genre, hand-made jigsaw allows you to cut bizarre lines requiring high precisionAnd electric - speeds up the process where urgentness does not need.

Important! Pay attention to the pinks. The smaller they have cloves, the more accurate will be cut.

Fastener

A table of plywood with their own hands, as well as a locker, a stool or hinged shelvesYou need to fasten only special self-draws. They are designed for fastening wooden details And perfectly hold even in the chipboard, not to mention the plywood and woody arrays.

To work with self-drawers, you will need a drill - manual or electric, and a drill set.

Important! The hole is done in advance, the hole is made, and it must be slightly less than the fastener diameter - about 2 mm.

Dining table from plywood do it yourself

Now you know how to choose a fane, how to work with it, and even tried to do small table. You can move to further accomplishments. For example, make a dining table from plywood with your own hands. It will be a little more difficult to make a journal, if you choose the materials correctly, and the process you already familiarize:

As with the manufacturer of the coffee table, draw a sketch and draw the patterns of legs and countertops.
Templates can be handed over to the printing house so that they are printed on a special self-adhesive film - then they can be pasted directly on the Phaneur and cover them.
Prepare Phanero - if it is too thin, glue 2-3 sheets with each other, should not be fed up the table.
Push the sleeve and surfaces if necessary.
From the bottom side of the table top, make places for the holes under the legs.
Remove them, but not through.
Hand milling machine Cut the top of the legs so that they are inserted into the prepared grooves.
Plore legs.
Put the table as it will stand.
Align the legs.

Round table of plywood

How to make a table from plywood with your own hands, if you have more to a round or oval form? Yes, just like any other. Just need a template template. If you need a coffee table small size, You can use a round tire. Only it must be very well to wash.

Important! There are options when the tire becomes part of the table - the tabletop is attached directly to it, so it turns out not only the table, but also the cavity for of different little things. But you can make it just a tabletop on the legs.

So, circle a tire on Faneru:

Cut the worktop.
Collect her.
Turn the back side.
Take a place for the leg.
Drill it.

Leg

The leg at such a small table is a wooden round stick on the cross, this is the easiest option. You can make a table and on four legs, but you need to position them correctly:

Put the worktop worktop face down.
Find the center (it must be done very accurately).
Spend 2 diameters at an angle of 90 ° to each other.
On these diameters, drill holes for the legs, retreating 5-10 cm from the edge.
Put the legs or secure the corners.

Children's table of plywood do it yourself

If you have already tried to make a dining table or a journal of plywood, children's furniture problems for you will not be. Here the main thing is to make the table in size, and that the product is durable and safe. Therefore, we make it on the frame.

You will need:

a piece of thick plywood for the table top (you can glue from several sheets);
strips of plywood for frame and legs;
joiner tool;
fasteners

The order of work will be as follows:

Cut the blanks for the legs - by templates, if necessary, glue the legs of several layers.
Prepare a worktop (glue from multiple layers, shry).
Cut strips for the frame - the width of them is 10-15 cm, the length is 10 cm shorter than the parties.

Build an assembly from the frame, which is put under the tabletop:

Check how direct the corners are obtained.
Fasten the side of the frame side with furniture corners.
In the corners, screw the legs so that their upper parts are inside the frame.
The countertop can be glued or secured with self-drawers.
Be sure to eat corners.
Puck the table top with the edge ribbon.
The legs can be connected to the crossbars at the bottom for greater stability of the entire structure.

How to separate the table?

It depends on what it is intended for which technology you collected it and which furniture you already stand. The only thing you should not do is to paint. But other options are many:

lacquer;

In a word, the manufacture of a table of plywood is a process available even to a novice master. The most important thing in this story is to find suitable materials and buy good tools. Try, and maybe you will have a real masterpiece, a worthy palace, because even the most famous masters from something started.

The reserves of natural building materials on our planet are limited, and they are replenished much slower than they are spent - therefore the idea of \u200b\u200busing recycles for the manufacture of beneficial things is far from Nova and is particularly popular in lately. Especially since some types of such raw materials are perfect to make a great dining table for the country or in a gazebo. And if you make quite a bit effort and fantasy, then you can do great table in the kitchen.

About a few interesting and original ideas for the manufacture of stylish and, most importantly, comfortable tables, we will tell more. But make such tables, bringing their "highlight" into their design - your task.

Pallet table - solidity, thoroughness and reliability

To understand how to make the table from the pallets do it yourself most simple way, I must first decide which pallets will go to the manufacture of the table.

The structure of the pallet is shown in Fig.1.

Flooring from extreme and intermediate boards is most often used for tabletops and side planes of the table, and checkers (in some types of pallets, they can be replaced by bars running along the transverse boards) - as connection nodes of the parts of the table.

Loft Table - Or Design Table

For the table, the size of 800x1200x750 mm, 3 pallet will be required. The table depicted in photo 1 will require them as many as 6 pcs., And may have a different configuration, since it consists of two identical modules. Manufacture such a couple, you can simulate differently kitchen space.

In addition to pallets, we will need: nail-holder, manual circular Saw, Confirmates (or nails) for screed parts of the structure, grinding, spatula, putty and paint on wood, varnish.

Preparation for assembling design. Disassemble pallets as follows:

Collect P-shaped design The table, connecting the worktop with the pallets supplied on the ribs and tightening them with confirmates.

For reliability, you can additionally install furniture corners with back side Countertops.

The central checkers of the side parts of the table connect the additional crossbar made from the transverse board, which remained after dismantling the first pallet.

Finish finish Designs. Carefully slip irregularities external surfaces Tables, paying special attention to the countertop and the ends of the boards. Give putty dry and re-pollue outdoor design elements. Paint needed color and coat with two layers of varnish.

As you can see, the table from the pallets do it yourself very simple - for this you only need imagination and attention to detail. Try to make a table with photo 2 - you will see, you will succeed!

Post-table table top: Classic genre of the desired size

And again the old kind of classic, but created with his own hands.

Need a very small segment of furniture countertops to save significantly on buying dining table. for kitchen. It will be about how to make a table from the table top with your own hands. Classical kitchen table (Photo 3) is almost no different from furniture purchased in the furniture cabin - except, the sizes of the table top, ideal for your kitchen.

We need the following materials and tools:

A piece of tabletop from chipboard (if you buy it for these purposes - ask for sellers to bring it to you immediately the desired size);

Set of table legs - optimal will buy round legs with a height of 710 mm (diameter 60mm);
T-shaped furniture Cant (with girth and installation spike). All listed materials can be seen in Fig.3.

From the tools, we will need: an electrolovik, grinding (preferably - tape), a drill with a nozzle-cutter (or an end disk saw), a screwdriver. Also need a hammer with a rubber nozzle, sealant, self-tapping screws to fasten the legs to the tabletop, a caliper and a conventional drawing circuit.

After the entire material is assembled, the tool is prepared - you can begin to make your own table from the tabletop.

1 Stage of work - Making countertops:

Shaping;
a) We make a mark of 10 cm from the corner, on each side of the countertop. The roundabout center is located at the point of intersection of perpendiculars spent from these marks to the sides of the tabletop rectangle. Radius of the circular solution - 10 cm. Blacks of rounding of all angles;

b) the electroll bitch gently voiced the corners of the table tops on the marked arcs. To avoid chipping chips, the filling for the jigsaw must be taken with a reversing direction of teeth;

c) carefully process cuts with grinders;

Edging;

d) Schunzirkul measuring the distance from the side of Kant to its spike. At the same distance from the upper plane of the table top, we carry out the line in its end;

e) the cutter is chosen the groove on this line;

e) Hammer with a rubber nozzle carefully clog the edging of a spike in the groove. For greater strength, it is desirable to apply silicone to the end;

Legs;

g) Place the places for the legs of the table;

h) 25 mm screws screw holders;

and) Install the table support.

Table - Puzzle from birch plywood: originality, simplicity and style

How to make a table from plywood with your own hands, can be seen in the diagram (Figure 4). Such a table will decorate any room.

The material for the manufacture of such furniture is better to take birch, sheet thickness - 30-35 mm.

You will need: plywood sheets - 2500x750 mm and 1500x1500 mm, drawing tool, jigsaw, PVA glue (if the product is planned inseparable), grinders, sandpaper and finishing materials.

The feature of the table from plywood is an assembly without a single fastener, and how with their own hands you can make it as convenient as possible in the height and size of the countertops - to solve you. The round table in Figure 4g has a height of 750 mm and the diameter of the table top 1500 mm.

The manufacturer's algorithm is next

Marking. In accordance with the drawing, the details A and B are absolutely identical on the contour, the difference is only in the depths of assembly grooves. Therefore, it is better to make one template (from Watman), and on it already make marking on the plywood. Pay attention to the selection in red: the groovers must be on the same line, and their width (like the height of puzzle protrusions at the top of the parts) is equal to plywood thickness.
Drinking and processing details. The attention is important here and accuracy: the strength and stability of the product depend on them. Grinding, toning and varnishing coating should be carried out on all parts of parts, including ends.
Assembly. With a qualitative execution of previous steps, the assembly will not take much time: we connect the parts A and B (in the groove), the part b wept on top of puzzle protrusions. If the fastening elements of the Podstoley are somewhat performed above the table top plane - they must be counted (grinding). Covered details finish layer Laca - Table ready!