Installation of underfloor heating Electrolux. An overview of the characteristics and rules of installation under the tiles of a warm electric floor from Electrolux It is important to consider

Electric heating systems from the world famous manufacturer Electrolux, based on cable heating products and special heating mats, are mainly reassigned for comfortable heating of premises by heating the floor surface, under which the heating system is actually mounted.

Note that the premises in which it is possible to organize efficient electric floor heating can be not only residential, but can also be used for efficient and energy-efficient heating of public and office premises.
Electrolux underfloor heating, the installation of which will be given below, does not require mandatory installation in the sand concrete screed, it is enough to lay cable products or a heating mat in a previously prepared tile adhesive solution.

Advantages of underfloor heating over radiator heating

The manufacturer has taken care of the compactness of its products and when laying the heating system for heating the floor surface, the level of the latter rises to minimum values.

Initial phase: planning

At the initial stage, which implies the organization of such a heating system for rooms as Electrolux underfloor heating, the instructions for which are included with this equipment, it is necessary to plan future installation work.

The algorithm for such planning is quite simple to start with:

Conduct an audit electrical wiring in the room in which this heating system will be installed for high-quality and uninterrupted connection. For this, the power indicators of all devices are summed up, which can be connected during the operation of the heating system to the mains. It is also necessary to take into account the various devices that can also be connected, but are not required to be permanently connected.
Underfloor heating Electrolux, installation of which must be carried out by a specialist, and with a power of more than 2 kW, it is recommended to connect through a separate machine to a specially brought out wiring. In addition, it is advisable to connect through an RCD (nominal response rates are not higher than 30 mA).
Before laying heating mat or cable products, the resistance of each of the elements of the system should be measured (this data is recorded in the warranty card). If everything is in order, then the recorded parameters must correspond to the factory parameters (indicated by the manufacturer in the instructions).
The next step is the most important - it is the drawing up of the layout of the electric heating system for underfloor heating. Note that the distance between the system and other heating devices, walls or communication ties must be at least 30-50 cm.

Heating system laying: features

Before laying a product such as Electrolux underfloor heating, the installation of which is quite simple, nevertheless, it is better to entrust it to specialists, you should first prepare the surface: remove pointed objects, excess construction waste, as well as irregularities to ensure a smooth base for laying a cable or a heating mat.
Further, the location of mats or heating cable products is determined, taking into account the peculiarities of the geometry and the room, as well as the furniture located in it.
Also, do not forget where the temperature sensor and thermostat will be located.
Further, underfloor heating Electrolux installation implies placing directly heating elements- after they are placed, make sure that the wires of the temperature sensor and power cables do not touch each other.

This is important to consider

We pay special attention to the fact that is strictly prohibited use different kinds extension cords or independently build up wires, these actions significantly reduce the safety of the system and can cause an emergency.
Heating products should be laid with the smooth side on the base, after which the product is adjusted according to a previously made scheme.
If it is necessary to obtain the desired shape of the mat, it is possible to cut the product only in those places of the heating structure where the frame fabric is present.
Cut the heating cable itself it is forbidden, as this will compromise the integrity of the heating system.
The distance between the heating elements must be the same, but not less than 5 cm.
When installing an electrical heating system for underfloor heating, do not use an overlapping connection of heating elements.

Correct installation of the system structure guarantees a long and safe service life.

Transcript

1 Warm floors Electrolux catalog 2013

2 2 electrolux underfloor heating electrolux underfloor heating 3 Range Rated power Installation method Scope of application Optimal Floor covering material Compatible Heating mats and indoor sections Easy Fix Mat 150 W / m 2 Wet tile adhesive, thin screed Floor in bathroom, kitchen and living quarters rooms Tile, stone Laminate, linoleum, carpet Multi Size Mat W / m2 Wet Tile adhesive, thin screed Floor in bathroom, kitchen and living rooms Tile, stone Laminate, linoleum, carpet Alu Mat 120 W / m2 Dry or wet Direct installation under flooring or in a thin screed Floor in living rooms Laminate, parquet, carpet, linoleum Tile, stone Twin Cable 17 W / m. Damp Screed Floor in living rooms, bathrooms, loggias Tiles, stones Laminate, linoleum, carpet The history of Electrolux The Swedish concern Electrolux is the world's largest manufacturer of household appliances and professional equipment. Since its founding in 1919, Electrolux has created and presented to consumers many outstanding innovations in a wide variety of fields. The key to the success of Electrolux products over the decades has been and remains its impeccable quality. In the production of all equipment, the concern is guided by a single principle: the difference in price is due only to the presence or absence of additional functions, but not to the difference in the quality of goods. The history of Electrolux is inextricably linked with cable heating systems, also known as underfloor heating. For over 10 years the company has been offering innovative solutions for space heating using a heating cable. During this time, unique products have successfully passed the quality test during operation and gained popularity all over the world. Today Electrolux presents at Russian market a new line of heating mats, cable sections and de-icing systems for buildings and adjacent areas. Electrolux products have the European CE quality certificate and comply with all necessary European and Russian standards: environmental standards, hygiene standards fire safety the highest indicators of energy efficiency. Electrolux brand advantages: Product development tailored to the needs of the end consumer Variety of product groups Consumer loyalty to the Electrolux brand and professional experience Brand awareness 70% Representation in chain stores with household appliances Investment in innovative developments Slim Single Wire Cable 10 W / rm. Wet Antifrost Mat Outdoor 300 W / m 2 Wet Dry Step Mat Outdoor 300 W / m 2 Wet Antifrost Cable Outdoor 30 W / m. Dry Frost Guard Pipe Cable 17 W / m.p. Dry Thermotronic Basic Thermotronic Avantgarde Thermotronic Touch Tile adhesive, thin screed or floor on logs Floor in living rooms, pipes, foundations Parquet, laminate, carpet De-icing systems for outdoor installation 16 A (3600 W) 16 A (3600 W) 16 A ( 3600 W) Installation in road surfaces Installation in steps or under tiles Open way on the roof and into the gutters On the outer surface of the pipe Thermostats Concealed installation in the installation box Driveways, platforms Porch steps, paths Concrete, stone Concrete, stone, tiles Concrete, stone, tiles Asphalt Asphalt Roofs, gutters - - Heating pipes - - Underfloor heating systems Programmable underfloor heating systems for a day Programmable underfloor heating systems for a week Tile, stone, parquet, laminate, carpet Tile, stone, parquet, laminate, carpet for a day Tile, stone, parquet, laminate, carpet for a week

3 4 electrolux underfloor heating electrolux underfloor heating 5 Electrolux underfloor heating: a new generation of electric cable heating systems The high quality standards of modern housing dictate strict requirements for the temperature of the floor covering, because the floor is the surface in the room with which a person is most often in direct contact. The feeling of warmth and comfort in the house largely depends on the floor, which is especially important for countries with a temperate climate and a sharp daily temperature drop, such as Russia and most of the CIS countries. In cities, the problem becomes more acute during the off-season, when the heating season has not yet begun, and it is already cold at home. Additional difficulties are created by the often weak thermal insulation of houses, especially of the "economy" class. Standard convection heating systems do not always provide enough heat in the room. When using them, the air temperature at the head level reaches C, while the floor temperature remains low - about C. With such a heat distribution, a person experiences discomfort: the floor is cold, and the room itself is stuffy. The temperature of the floor covering is considered more natural and optimal, and the temperature at the head level is about C. It has been established that this temperature ratio creates a feeling of comfort, reduces convection flows and does not dry out the air in the room. Among the main advantages of Electrolux products, it is worth noting, firstly, direct heating of the floor surface. The direction of the heat flow from bottom to top over the entire area and the distribution of heat in the vertical direction create a natural feeling of comfort. Secondly, compared to concentrated heat sources (radiators, convectors, fireplaces, stoves), warm floors create much less convection flows, drafts, which, among other things, means less dust in the air. Thirdly, the only visible element of the system is the thermostat. The heat source is hidden under the floor, making room for furniture and various interior solutions. Fourthly, due to the absence of direct contact of the heating elements with the atmosphere, the air does not dry out. At the same time, the humidity in damp rooms, such as bathrooms and hallways, is ideally regulated, and this is a guarantee against mold formation. Fifth, the set temperature is maintained automatically. Heating mode can be programmed. And finally, the service life of Electrolux cable systems is more than 50 years, and Maintenance they don't need it. The warranty period is 20 years. In addition, the installation of underfloor heating is an ideal solution for residential and industrial premises of medium and small area... Without cluttering small rooms with massive heating appliances, you can effectively solve the heating problem. Moreover, thanks to the installation of underfloor heating in any, even the most budgetary housing, consumer qualities increase significantly. And, of course, no full-fledged major overhaul of an apartment, as a rule, is complete without the installation of warm floors. Unlike water heating systems, installation of cable systems does not require obtaining approvals from the administrative bodies of housing and communal services, there is no danger of leaks, there is no risk of flooding the neighbors, it is easier to control the temperature. It is easy and simple to install cable systems, besides, their service life is much longer than that of water systems. Thus, modern solutions Electrolux sets a new level of quality, reliability and efficiency. And most importantly, with Electrolux warm floors - your home will always be warm, no matter what happens. As practice shows, no heating system provides such uniform heating as a warm floor. Taking into account the experience of the world's best manufacturers, Electrolux has brought to the market a unique line of technically perfect, versatile and easy-to-use cable heating systems Distribution of convection flows in a room with a traditional heating system using radiators Electrolux underfloor heating systems - heating mats, cable sections for underfloor heating and modern thermostats - capable of creating an ideal microclimate and maintaining optimal heat distribution in the room throughout the year. Anti-icing systems will reliably protect the house from freezing pipes, icicles or ice formation. Distribution of convection flows in a room with a "warm floor" heating system

4 6 electrolux underfloor heating electrolux underfloor heating 7 Main advantages of Electrolux cable heating systems 35% PTFE insulation The insulation of the heating cores is made of PTFE, one of the most famous names of which is Teflon (R). PTFE has a wide range of mechanical properties, good dielectric properties, high electrical strength, and low wear characteristics. In addition, it is resistant to the effects of various aggressive environments at room and elevated temperatures, is weakly gas permeable, self-extinguishes when ignited, and has high resistance when heated (up to 300 C). The use of fluoroplastic insulation provides maximum safety and reliability characteristics with a minimum cable thickness, and also increases the resistance to local overheating. Innovative textile base The unique textile base of Electrolux heating mats of the EASY FIX MAT series is made on the basis of a fabric impregnated with a special adhesive that forms ideal conditions for adhesion to concrete and tile adhesive, eliminating the formation of air bubbles in the solution and cracks in the screed, creating a reinforcing effect of the floor surface ... The innovative technology allows the heating cable to be woven into the textile base, which ensures a uniform structure of the mats. The textile base, in contrast to the base in the form of a fiberglass mesh, does not deform during transportation or long-term storage, and the mat, when laid, ideally lies on the floor surface without the formation of bumps. Also, with small shifts of a part of the mat to the side, its level does not rise: it is evenly distributed over the floor surface. Unique stretch base up to 35% The woven base of the MULTI SIZE MAT series is made in the form of elastic bands, due to which you can stretch the laid mat, increasing its length up to 35% of the original. At the same time, the power of the mat per unit of laying area changes proportionally. The variable power range of the mat from 150 W / m 2 to 111 W / m 2 opens up new possibilities for optimal floor heating in any type of room. In addition, the reduction in power allows the use of the screed mat under wooden floor coverings. If desired, the mat can be stretched only in certain areas, thus forming local zones with different heating intensities. Three layers of insulation Electrolux cable products use an additional second layer of insulation for the heating conductors. Thus, three layers of insulation are used: individual insulation of the heating cores, additional belt insulation and an outer sheath, which reliably protect the heating elements of the core from damage, depressurization and moisture penetration during the entire service life. The second layer of insulation covers any possible defect (for example, microcracks) in the first layer. Double and reinforced insulation provides better resistance, withstanding up to 4000 V breakdown voltage. The outer sheath of the heating cable is resistant to the chemical composition of concrete and tile adhesive. This ensures a long service life for Electrolux heating cables. ARAMID 25. C High strength aramid synthetic fiber The basis of the Electrolux heating cable is a unique core made of aramid threads. Aramid, also known as Kevlar (R), is a synthetic fiber with high mechanical and thermal strength. Aramid fibers do not conduct electric current, do not have a melting point (destruction begins only at 500 C), are characterized by a high mechanical strength... This material is 5 times stronger than steel and is used in the manufacture of body armor, fire retardant clothing and reinforcement of tires. Heavy-duty aramid conductor provides the highest strength characteristics of Electrolux cable products. Variable styling An innovative solution Electrolux elastic Multi Size Mat on a textile stretch backing. Mats on an elastic base, in contrast to mats on a rigid mesh, make it possible to vary the form of laying: from the usual rectangular form to laying in the form of a diamond, arc or trapezoid. Thus, without cutting the mat, you can bypass all the "obstacles" and install a warm floor in rooms of complex configuration. This is very convenient for installing underfloor heating in rooms with non-standard sizes eg in bathrooms, hallways or kitchens with large stationary appliances. For fastening to the floor, use the special fasteners included in the kit. Touchscreen display Following global digital trends, Electrolux is developing the Thermotronic Touch series with touchscreen display, which has an intuitive interface that instantly responds to user touch. A large graphical screen with a pleasant blue backlight displays the air temperature, current time, as well as the state of the system (whether it is on or not). The built-in menu helps to manage all the thermostat functions in the same way as when using a smartphone. Thus, thermostats with touch screens of the Thermotronic Touch series are highly reliable and have an intuitive interface. A set of programming functions allows you to customize the system to suit your rhythm of life and help reduce energy consumption. Ergonomic design The interior of any living or work space is ergonomic to a certain extent, which is achieved by effective systems management. All of them are aimed at ensuring that interior items constantly give a person a sense of comfort. When developing the Electrolux Thermotronic Basic thermostat, considerable attention was paid to harmonious combination texture and color scheme. As a result, this made it possible to perfectly fit it into any design solution - from classic to high tech. The shape of the thermostat and the control system are as user-friendly as possible. The device owes its properties to the use of high-quality materials, as well as to the painstaking work of designers and engineers.

5 underfloor heating electrolux 9 8 electrolux underfloor heating Two heating conductors Under any covering Both conductors are heating, the load is evenly distributed on each of them, which increases the service life of the cable. The underfloor heating set can be laid for any type floor coverings: tiles, laminate, parquet, carpet. Braided copper shield Self-adhesive surface In accordance with the requirements of international safety standards, the cable has a braided copper shield for grounding during operation. By applying an adhesive to the entire textile base and three special adhesive tapes, the heating mat is securely fixed to the floor surface during installation. This prevents the mat from shifting during the application of the tile adhesive. Minimum bending radius The design allows bending the cable without the risk of breaking or breaking the cores. This is achieved through a unique design of thin, twisted heating conductors, the length of which exceeds the length of the cable by 6%. In case of any deformations or stretching, the main load falls on the aramid core, and the heating conductors are easily adapted to changes in geometry. Warranty 20 years The warranty period for Electrolux heating mats and cable sections is 20 years. At the same time, the service life of cable electric heating systems is more than 50 years, and maintenance is not required. Increased tensile strength A cable in a screed or tile adhesive constantly experiences loads of various directions during heating and cooling: axial, radial. It is very important to protect the heating elements from these influences. The Electrolux cable is based on an aramid core, due to which it can withstand a breaking load of up to 200 Newtons. Easy installation. Installation of equipment does not require special skills and knowledge. Laying without screed The underfloor heating set is designed for laying in a layer of tile glue or mastic without using a screed. This method minimizes the level of floor rise. Bi-metal sensor Bi-metal sensor Programmable thermostat allows you to set individual temperature conditions for every hour during the day. Heating pipes Automatic maintenance Temperatures The Frost Guard Pipe Cable series is designed for heating pipes. The device has the function of automatically maintaining the level of the set temperature. Setting the temperature with an accuracy of 1 C Heating distribution LCD screen with backlight With this thermostat, you can set the required floor temperature with an accuracy of 1 C. Each turn of the ALU MAT series heating cable is built into a double aluminum screen, significantly expanding the heating element, which allows even warmth over the floor area. This design is especially important for installing the mat under wooden coverings. The additionally improved heat distribution accelerates the heating of the floor surface and reduces energy consumption. Floor and air temperature sensor included The thermostat allows you to set the maximum and minimum floor temperature corridor. When it cools down below the level of the set minimum temperature, the warm floor will turn on, when it warms up above the maximum temperature, it will turn off. In addition to the floor temperature sensor on the wire, the thermostat is equipped with a built-in air temperature sensor. Connection to the 220 V network The heating mat has a power of 150 W for square meter paving area, which is optimal for creating comfortable heating. The EFGPC series cable section is equipped with a standard plug for connecting to a 220V outlet. 25. Thin sleeve The design is equipped with a thin sealed sleeve. It has practically the same diameter as the cable itself, which minimizes the amount of floor level rise. Child lock The thermostat supports the control panel lock function to keep small children safe. UV protection The thermostat is equipped with a floor temperature sensor on the wire. The polyolefin outer insulation of the cable is resistant to ultraviolet radiation and other atmospheric influences, which is especially important when operating anti-icing systems. Intuitive interface Energy saving The instrument has an intuitive interface. Anyone can easily operate the "warm floor" system without prior preparation and training: just read the instructions. The programmable thermostat can save energy consumption by up to 30%. Temperature sensor included. Screed The temperature controller is equipped with a contrast LCD display with backlight. Setting the temperature corridor. Power 150 W / m 2 The Twin Cable underfloor heating set is designed for laying in a concrete screed with a height of at least 3 cm. The recommended height is 5 cm. pipe temperature from +3 C to +15 C. Polyolefin Warranty 3 years The warranty period for Electrolux is 3 years. Switching current 16 A De-icing systems The product is intended for outdoor de-icing systems. (3600 W) thermostats Permissible operating load of the thermostat: power up to 3600 W, current up to 16A. Changeable color panels Programming by day of the week The thermostat allows you to set the program for weekdays, weekends, as well as for each day separately. The basic color of the thermostats is "ivory". However, to create exclusive design solutions, it is possible to install interchangeable color panels. The base color of the panel can be easily changed to white, silver or black (not included).

6 10 electrolux underfloor heating electrolux underfloor heating 11 Heating mats for rooms We thought that you need not just a warm floor, but an intelligent heating system that adjusts to your rhythm of life and creates an individual microclimate in the house. Versatility and simplicity Continuously looking for innovative solutions and at the same time caring for you, Electrolux offers versatile heating mats that will be indispensable in any modern house... Innovations Electrolux offers 3 series of mats: Easy Fix Mat - the most convenient and simple solution for a household floor, self-fixing during installation due to an adhesive layer, Multi Size Mat on an elastic base that stretches to 35% of its original length, and Alu Mat - universal mats in living rooms for any kind of flooring. Among the main advantages of all mats are fast and uniform heating of the floor surface, installation in tile adhesive provides a minimum rise in the floor level. Electrolux heating mats are the most affordable way to make floors warm, since their installation does not require pouring a concrete screed, calculating the power and cable laying step, as well as having special knowledge. Even if you are not a professional builder, you can install the mat at home on your own, in fact, simply spread the roll over the required area. The help of an electrician is only required to connect the system to the thermostat.

7 underfloor heating electrolux electrolux underfloor heating Easy Fix Mat Series Installation area m 2 Power, W Mat length, m Resistance, Ohm -5 / + 10% 0.7 1.3 2.6 3.2 EEFM, 7 EEFM, 2 EEFM EEFM, 8 EEFM, 4 EEFM, 3 EEFM EEFM, 2 EEFM Article number EEFM, 5 EEFM EEFM, 5 EEFM EEFM, 5 EEFM EEFM, 5 Series Easy Fix Mat Self-adhesive heating mat based on a thin two-core cable. The two-core heating cable is firmly woven into a textile mesh impregnated with a special adhesive, which securely fixes the mat to the floor and creates ideal conditions for adhesion to concrete and tile adhesives. Easy Fix heating mats are ideal for those rooms where it is necessary to keep the floor thickness low. Their main area of application is under tiles or natural stone, in tile adhesive without screed, as well as in screed under any floor coverings: laminate, carpet, parquet and linoleum. Power 150 W / m2 Warranty 20 years Super strong aramid conductor Easy installation PTFE insulation Thin sleeve Two heating conductors Three layers of insulation Innovative textile base Braided copper screen Increased tensile strength Laying without screed Self-adhesive surface Power density 150 W / m2 at 220 V Textile mesh improved adhesion properties to concrete Thin two-core cable 3.5 mm Self-adhesive mat base Thin sealed sleeve, one-sided connection Cable type two-core Mat power 150 W / m2 Cable power 11 W / m Voltage 220 V, ~ 50 Hz Mat width 0.5 m Thickness mat 3.5 mm Cable pitch 7.4 cm Length of connecting cable 2 m For any ARAMID coating

8 underfloor heating electrolux electrolux underfloor heating Multi Size Mat Series Laying area m 2 Power, W Mat length, m Resistance, Ohm -5 / + 10%, 7 1.1 EMSM, 3 EMSM, 6 EMSM, 7 EMSM, 2 EMSM EMSM , 8 EMSM, 4 EMSM, 3 EMSM EMSM, 2 EMSM Article EMSM EMSM, 5 Series Multi Size Mat extra-thin heating mat on an elastic base. The unique stretch design allows the mat length to be varied from 10% to 35% of the original, thereby changing the heating area and mat power from 150 to 111 W per m2. By stretching and bending the Multi Size Mat, you can vary the styling shape from the usual rectangular to diamond or trapezoidal, avoiding any “obstacles”. It is very convenient for installing underfloor heating in rooms with non-standard dimensions. Recommended for installation under any floor coverings, including wooden ones. Power density W / m2 at 220 V Thin two-core cable 3.5 mm Stretchable base within 10-35% of the original length Variable shape of the laying area Thin hermetic sleeve, one-sided connection Cable type two-core Mat power W / m2 Cable power 11 W / m Voltage 220V, ~ 50 Hz Mat width 0.5 m Mat thickness 3.5 mm Cable laying spacing 7.4-9.25 cm Length of connecting power cable 2 m Laying without tie 35% Unique stretchable base up to 35% W / m2 ARAMID Variable power W / m2 Easy installation Super-strong aramid conductor Variable installation shape Suitable for any coating PTFE insulation 20 years warranty Two heating conductors Three insulation layers Thin sleeve Braided copper shield Increased tensile strength

9 16 electrolux underfloor heating electrolux 17 Series Alu Mat Article Number of laying area m 2 Power, W Mat length, m Resistance, Ohm -5 / + 10% EAM, 33 EAM, 5 1.89 EAM, 67 EAM, 44 EAM, W / m 2 Power 120 W / m 2 Easy installation Heating distribution 20-year warranty Alu Mat series universal mat for all types of flooring: tiles, carpet, laminate, linoleum. The unique patented design of the mat, based on an ultra-thin cable and aluminum shields along the cable, allows for an even distribution of thermal energy... Such a mat can be installed directly under wooden flooring or carpets using the dry-laying method, as well as the classic wet-laying method under the tiles. Alu Mat has a balanced power and improved characteristics of the distribution of heating over the area, which eliminates the "heat zebra" effect and overheating of the floor covering in places of contact with the heating elements of the mat. Dry and wet installation Suitable for any surface Power density 120 W / m2 at 220 V Super thin cable 1 mm Universal for any floor covering Any installation method Aluminum strips distribute heat Fast heating Thin sealed sleeves, one-sided connection Additional energy savings Cable type single core Mat power 120 W / m 2 Cable power 7.5 W / m Voltage 220 V, ~ 50 Hz Mat width 0.5 m Mat thickness 1 mm Cable laying pitch 6.25 cm Length of connecting power cable 3x2 m

10 18 electrolux underfloor heating electrolux underfloor heating 19 Heating cable sections for rooms We thought that when planning a renovation, you would like to create comfortable atmosphere for the whole family, regardless of the configuration of the room, using modern environmentally friendly systems with minimal energy consumption. Reliability The classic type of underfloor heating systems Electrolux cable sections, laid in a concrete leveling screed during the construction or overhaul phase. The basis of the Electrolux cable is an aramid core, which is several times stronger than steel. Due to this, the cable can withstand a breaking load of up to 200 Newtons. reduced tariff, and turning off the system during the day. The cable sections are ideal for complex floors and can be installed in concrete, tile adhesive or under stone. Three layers of cable insulation reliably protect the core heating elements from damage, depressurization and moisture penetration during the entire service life. The cable is resistant to the chemical composition of concrete and tile adhesive. The flat sealed sleeve has nearly the same diameter as the cable itself, which minimizes the amount of floor rise and reduces the likelihood of damage to the system. Accumulating effect Underfloor heating based on a cable section makes it possible to create a complete heating system in a room with an accumulating effect. Due to this, you can significantly save energy costs, accumulating heat at night, when

11 underfloor heating electrolux electrolux underfloor heating Twin Cable series Twin Cable series thin two-core heating cable of high power 17 W / m. Both heating conductors of the cable are heating conductors, which ensures rapid heating of the floor. The thin sealed sleeve has nearly the same diameter as the cable itself, which minimizes the amount of floor rise and reduces the likelihood of damage to the system. Super-strong aramid core and three-layer insulation reliably protect the cable from accidental damage and overheating throughout its entire service life. The cable is resistant to chemical bonding of concrete and tile adhesive. Recommended for laying in concrete screed, suitable for rooms with complex configurations. Cable type two-core Cable power 17 W / m Voltage 220 V, ~ 50 Hz Cable diameter 4.5 mm Length of the connecting power cable 2 m Powerful universal two-core cable Power consumption 17 W / m at 220 V Fast heating, both heating cores Thin sealed sleeve , one-sided connection Reduced cable thickness 4.5 mm Any form of laying area Reliability and durability Heating area, m 2 at specific power, W / m 2 * Power, W (220V) Length, m Resistance, Ohm -5 / + 10% ETC , 8 0.7 0.5 ETC, 7 1.3 1.0 ETC, 6 161.3 2.5 2.0 1.5 ETC, 3 2.7 2.0 ETC, 4 96.8 4.2 3.3 2.5 ETC, 3 80.7 5.0 4.0 3.0 ETC, 1 60.5 6.7 5.3 4.0 ETC, 8 48.4 8.3 6.7 5, 0 ETC, 6 37.4 10.0 8.0 6.0 ETC, 5 10.0 7.5 ETC, 6 22.5 16.7 13.3 10.0 ETC, 1 17.9 20.8 16 , 7 12.5 Item No. Screed Minimum bending radius Fast heating time Three layers of insulation Two ARAMID heating conductors Super-strong aramid conductor Braided copper shield Power 17 W / m 20-year warranty Increased tensile strength Thin sleeve ta * Specific power is determined depending on the type of heating required: optimal 120 W / m2 installation step 14 cm; comfortable 150 W / m2 laying step 11.5 cm; basic 200W / m2 installation step 8.5cm. Data are average, please contact your dealer for exact calculations.

12 22 electrolux underfloor heating electrolux underfloor heating 23 Series Slim Single Wire Cable Article Power, W Cable length, m Resistance, Ohm -5 / + 10% Laying area m 2 at 120W / m 2 ESSWC ESSWC, 7 2 ESSWC ESSWC, 3 4 ESSWC ESSWC, 8 6 ESSWC, 7 8 ESSWC, 1 9 ESSWC, 5 10 ESSWC, 8 11 ESSWC, 4 13 ESSWC ESSWC, т3 15 Slim Single Wire Cable Series Slim single-wire cable for universal use. It is used to organize comfortable floor heating with any floor covering and in rooms with complex configurations, as well as to protect against soil freezing and heating pipes. The cable's average power per linear meter and small thickness make it ideal for laying under wooden floors and soft floor coverings. The “invisible” sleeve has the same diameter as the cable. Laying in a screed Minimum bending radius Laying without a screed Three layers of insulation Thin single-core cable 4.3 mm Power consumption 10 W / m at 220 V Thin "invisible" sleeve Under any floor covering For economical solutions Double-sided connection Cable type single-core Cable power 10 W / m Voltage 220 V, ~ 50 Hz Cable diameter 4.3 mm Lengths of connecting cables 2x2 m Braided copper screen Warranty 20 years ARAMID 10 W / m Super strong aramid core Power 10 W / m Thin sleeve Increased tensile strength

13 24 electrolux underfloor heating electrolux underfloor heating 25 De-icing systems Everyone knows how much trouble slippery paths, steps or icicles on roofs can cause. We thought about your safety and created highly efficient and modern anti-icing systems. Applications Electrolux offers a range of modern and reliable solutions for effective fight with icing of adjoining areas, stairs, roof sections, soil, as well as to protect pipes from freezing. Electrolux de-icing mats and cable sections have a 20-year warranty. Functionality Electrolux solutions are based on heating mats and cable sections. In the first case, it is enough to simply build the mat under any site, thereby preventing the formation of ice or snow cover. With such systems, you can safely forget about slippery paths, clearing stairs and the danger of slipping. The second option is cable section-based de-icing systems designed specifically for countries with harsh climates. The cable has several layers of insulation and is reliably protected from ultraviolet radiation and other atmospheric influences. The household series of solutions for heating pipes has a unique design, which includes a bimetallic sensor that constantly measures the temperature of the pipe in the range from +3 C to +15 C, regulating the power of the cable. The system is equipped with a plug, therefore, in order to prevent the pipeline from freezing, it is enough just to plug the cable into a 220 V socket.

14 26 electrolux underfloor heating electrolux underfloor heating 27 Series Antifrost Mat Outdoor Article Number of laying area m 2 Power, W Mat length, m Resistance, Ohm -5 / + 10% EAOAM, 3 EAOAM, 7 EAOAM, 8 EAOAM, 3 EAOAM, 3 EAOAM , 9 EAOAM, 0 EAOAM, 2 EAOAM, 9 EAOAM, 1 EAOAM, 7 EAOAM, 4 EAOAM, 4 EAOAM, 5 EAOAM, 8 EAOAM, 1 Series Antifrost Mat Outdoor single core mat on textile backing for outdoor use, designed for anti-icing applications adjoining areas, driveways and paths. The product characterizes high power, 100% sealed joint between heating and supply cables, double reinforced outer layer of insulation. Power of 300 W / m 2 will allow you to move on an ice-free slope road, reduce the risk of injury. A heating mat installed in open areas will allow them to be fully exploited. Electric cable heating for outdoor areas is the most economical way to remove snow and ice. Thin sleeve Braided copper shield 300 W / m 2 Power 300 W / m 2 PTFE insulation Power density of the mat 300 W / m 2 at 220 V Powerful cable with a double layer of outer insulation Thin "invisible" sleeve, 100% waterproof Variable shape of the laying area Possibility laying under asphalt Double-sided connection Cable type single-core Mat power 300 W / m 2 Cable power 30 W / m Voltage 220 V, ~ 50 Hz Mat width 0.5 m Mat thickness 5.6 mm Cable laying pitch 10 cm Length of connecting power cable 2х4 m Three layers of insulation 20-year guarantee ARAMID Super strong aramid conductor Anti-icing systems Increased tensile strength

15 underfloor heating electrolux electrolux underfloor heating Dry Step Mat Outdoor Series Laying area m 2 Power, W Mat length, m Resistance, Ohm -5 / + 10% EDSMO, 2 1.4 EDSMO, 5 1.6 EDSMO, 8 1.6 EDSMO, 1 2.8 EDSMO, 4 2.2 EDSMO, 7 2.8 EDSMO, 3 3.9 EDSMO, 6 3.8 EDSMO Part No. safety of movement on stairs and porch in the cold season. Using a heating mat will help you avoid mechanical methods cleaning ice or snow cover. The mat is 25 cm wide, fits directly onto the steps and prevents them from being covered with ice and snow. Laying in a screed Easy installation Fast heating time Anti-icing systems Two heating conductors Braided copper screen Cable type two-core Mat power 300 W / m2 Cable power 30 W / m Voltage 220V, ~ 50 Hz Mat width 0.25 m Mat thickness 5.6 mm Pitch cable routing 10 cm Length of connecting power cable 4 m Mat width 0.25 m Installation on steps Power density 300 W / m2 at 220 V Powerful two-core cable in black Simple and fast installation on steps Coupling point marked in red One-sided connection ARAMID 300 W / m 2 Super strong aramid core Power 300 W / m2 Warranty 20 years Increased tensile strength Thin sleeve PTFE insulation Innovative textile backing

16 30 electrolux underfloor heating electrolux 31 Antifrost Cable Outdoor Series Article Power, W Cable length, m Resistance, Ohm -5 / + 10% EACO, 3 EACO, 9 EACO, 7 EACO, 3 EACO, 4 EACO, 2 EACO, 8 EACO, 6 EACO, 7 EACO, 2 EACO, 6 EACO, 4 EACO, 8 EACO, 3 ARAMID Super strong aramid conductor Polyolefin UV protection Antifrost Cable Outdoor Powerful two-conductor cable for de-icing systems in adjoining yards and ground, roofs and gutters. Has six layers of insulation, including two braids: shielding and reinforcing. The outer insulation is UV and weather resistant. The series is specially designed for countries with cold climates. Prevents the formation of icicles and ice on the edge of the roof, in the gutters and ensures the unhindered outflow of melt water from the roof into winter season... Ideal for roof and gutter de-icing. Two heating conductors Double braided copper shield 30 W / m Power 30 W / m Increased tensile strength Universal two-wire cable for de-icing systems of roofs, gutters and adjoining areas Heat output 30 W / m at 220 V Six layers of insulation, including two braids : shielding and reinforcing Outer cable insulation made of polyolefin UV resistant One-sided connection Cable type two-core Cable power 30 W / m Voltage 220V, ~ 50 Hz Cable diameter 7 mm Length of connecting power cable 4 m Warranty 20 years PTFE insulation Anti-icing systems

17 underfloor heating electrolux electrolux underfloor heating Frost Guard Pipe Cable Frost Guard Pipe Cable frost protection cable for outdoor or indoor pipes unheated premises... Equipped with a standard plug for connecting to a 220 V network. Cable insulation provides protection against ultraviolet radiation and aggressive environmental conditions. Unique con- Item No. Power, W Cable length, m Resistance, Ohm -5 / + 10% EFGPC, 5 EFGPC, 8 EFGPC, 5 EFGPC, 9 EFGPC, 7 EFGPC, 3 EFGPC, 4 EFGPC, 9 EFGPC, 2 EFGPC, 4 EFGPC, 6 EFGPC, 7 EFGPC, 0 EFGPC, 1 EFGPC, 2 The cable structure includes a bimetallic sensor that constantly measures the temperature of the pipe and regulates the power in the temperature range from + 3 ° C to + 15 ° C. The sensor is based on the laws of physics and is mechanical, not electronic, to ensure long-term, trouble-free operation. Polyolefin Installed power 17 W / m at 220 V Bimetallic temperature sensor automatically changes the cable power in the range from +3 C to +15 C External polyolefin insulation resistant to UV and other weathering Standard mains plug Does not require a thermostat Installation on pipe Single-sided connection Cable type two-core Cable power 17 W / m Voltage 220 V, ~ 50 Hz Cable diameter 7x5 mm Length of the power supply cable 3 m Power 17 W / m Warranty 20 years Super strong aramid core Automatic temperature maintenance Bimetallic sensor PTFE insulation Connection to 220 V networks Two heating conductors Heating pipes Thin coupling Braided copper shield Increased tensile strength Minimum bending radius Bi-metal sensor UV protection ARAMID

18 34 electrolux underfloor heating electrolux 35 Thermostats for underfloor heating control We thought that the control of underfloor heating systems should be as simple as possible, and the energy costs are minimal. Ease of management. Model range In order to make the control of underfloor heating systems as easy and convenient as possible, Electrolux has provided the ability to install highly reliable thermostats. All Electrolux thermostats have an intuitive interface. Anyone can easily operate a warm floor without prior preparation and additional training: just read the instructions. V product line 3 series of thermostats are presented: Basic electronic with mechanical control of floor heating temperature, Avantgarde - programmable with an LCD display and Touch - with a touch display and the ability to program for the whole week. Electrolux thermostats practically do not take up space and harmoniously fit into any design solutions, becoming an integral part of the interior. The Touch is equipped with a childproof lock. Functions and modes The Basic series is equipped with a floor temperature sensor on the wire, and Avantgarde is also equipped with an air temperature sensor for wood flooring floor and heating systems. In addition, the thermostat allows you to set the maximum and minimum floor temperature corridor. Also, the Avantgarde model has the ability to set the temperature range for each hour during the day. The Touch series allows you to set the program for weekdays, weekends, as well as for each day separately.

19 underfloor heating electrolux electrolux underfloor heating Thermotronic Basic Series Thermotronic Avantgarde Series Operating voltage V, ~ 50Hz Maximum load current 16A Maximum load power 3.6 kW Temperature setting with an accuracy of 10C Power consumption 5 W Operating temperature range from + 50C to + 400C Dimensions , mm: 86x86x50 Programming temperature modes for every hour during the day Intuitive interface Energy saving Floor temperature sensor included Built-in air temperature sensor Replaceable panels of different colors LCD display with backlight Ergonomic design Possibility of setting the temperature corridor Installation hidden in the mounting box Warranty 3 years Voltage operating V, ~ 50Hz Maximum load current 16A Maximum load power 3.6 kW Temperature setting with an accuracy of 0.50C Power consumption 2 W Operating temperature range from + 50C to + 500C Dimensions, mm: 90x86x46 Floor temperature sensor included Possibility of replacing the frame per color color indication in operating mode Ergonomic design Mechanical control Possibility of setting the temperature corridor Concealed installation in an installation box Warranty 3 years (3600 W) Switching current 16 A Ergonomic design Replaceable color panels (3600 W) 25. Temperature sensor included 1 С Automatic temperature maintenance Setting the temperature corridor IP 20 Switching current 16 A Energy saving Programming during the day Setting the temperature with an accuracy of 0.5 ° С With a floor and air temperature sensor 3 years warranty Intuitive interface Protection degree Automatic temperature maintenance Warranty 3 years +0 , 5 oc Temperature corridor setting Backlit LCD screen IP 20 Replaceable color panels Degree of protection

20 electrolux electrolux underfloor heating electrolux electrolux underfloor heating series Thermotronic Touch Time programmable for weekdays and weekends Intuitive user interface Energy saving Floor sensor included Built-in air temperature sensor Changeable panels in different colors LCD display with backlight Touch control Childproof lock Possibility to install a corridor temperature Concealed installation in a back box Warranty 3 years Operating voltage V, ~ 50Hz Maximum load power 3.6 kW Temperature setting with an accuracy of 0.50C Power consumption 2 W Operating temperature range from + 50C to + 900C Dimensions, mm: 90x86x43 (3600 W) 25. Switching current 16 A Energy saving Programming by days of the week Temperature setting with an accuracy of 0.5 ° C With floor and air temperature sensor Replaceable color panels Childproof lock Intuitive interface Automatic temperature maintenance +0.5 ° C 25. Warranty 3 years Touch display IP 20 С warmth of protection

21 Electrolux is a registered trademark used under license from AB Electrolux (publ), S: t Gȯ. ransgatan, 143, SE, Stockholm, Sweden Thoughtful design innovation Do you remember the last time you opened a gift and exclaimed, “Oh! How did you find out? This is exactly what I wanted! " These are the emotions that Electrolux developers and designers strive to evoke in everyone who chooses and uses our products. We devote our time, knowledge and thoughts to anticipate your desires and create the kind of technique that you really need and that you dream of. By taking special care of our customers, we take a large part in an intuitive approach to innovation. Our main value is not a product in the name of a product, but a product in the name of its users. Guided by the principles of thoughtful design, we create a technique that is easy and pleasant to use, to give our customers the opportunity to enjoy the luxury of the 21st century in peace of mind. Our goal is to bring this peace of mind into the daily lives of as many people as possible. Therefore, when we say that we think of you, you know that we mean you. Electrolux. Thinking about you. Find out more about our ideas on and Version EKTP 2013/1

Electrolux Underfloor heating 2012 Product study Underfloor heating. Fundamentals of Thermophysics As practice shows, no heating system provides such uniform heating as a "warm floor". Spheres

Heated floors and anti-icing systems catalog 2014 Contents Contents Heated floors Electrolux catalog 2014 HEATING MATS Series Multi Size Mat 8 Series Easy Fix Mat 12 8 Heating mats

Heated floors and anti-icing systems catalog 2014 Contents Contents Heated floors Electrolux catalog 2014 HEATING MATS Series Multi Size Mat 8 Series Easy Fix Mat 12 8 Heating mats Series

Underfloor heating and anti-icing systems Electrolux 2016 Contents Contents Underfloor heating Electrolux Catalog 2016 Heating mats Series Multi Size Mat 8 Series Easy Fix Mat 12 Series Eco Mat 16 8 Heating

Underfloor heating and anti-icing systems 2017 24 Heating foil 30 Thermoregulators Contents Underfloor heating Electrolux Catalog 2017 Heating mats Series Multi Size Mat 8 Series Easy Fix Mat 12 Series

Warm floors and anti-icing systems 2019 Contents Assortment Warm floors Electrolux Catalog 2019 Temperature controllers Thermotronic Smart series 14 Thermotronic Basic series 16 Thermotronic Avantgarde series

Veria Veria Quickmat heating cable systems, Veria Quickmat single-core cable, Veria Flexicable 20 two-core cable Veria Control B45 and T45 Page 2

ELECTRIC HEATED FLOOR SOLELEC COMFORTABLE, WARM, SAFE www.rehau.ru Construction Automotive Industry REHAU ELECTRIC HEATED FLOOR SYSTEM DESCRIPTION For some areas of a modern apartment

"HEATING FLOORS" RAYCHEM Heating CABLES for COMFORTABLE HEATING OF FLOORS WITH VARIOUS COVERINGS WWW.pentairthermal.RU warm floors RAYCHEM individual solutions for heating floors with any coating Many

ADVANTAGES OF HEATED FLOOR "NATIONAL COMFORT" HIGH QUALITY Warm floors "National Comfort" are produced in Russia by the company "Special Systems and Technologies" at the largest plant in Europe. 100%

ELECTRIC FLOOR HEATING Version 2.0 / December 2011 PROGRAM OF EVENTS 1) Introduction. About TTS 2) Why do we need heated floors 3) Room comfort 4) Comparison different systems outdoor

HEATED FLOOR HEMSTEDT was the first to solve the problem of connecting heating and electrical conductors for a heating cable. Unique industrial technology HEM-SYSTEM connections excludes

CEILHIT products CEILHIT heating cables types PV, PSV are single core cables. The differences between them are determined by the presence of an additional protective shell or metal braid used

PRICE LIST for construction electric heating products December 23, 2014 HEATING FLOOR SYSTEMS - HEATING MATS IQ FLOOR MAT IQ FLOOR MAT - 150 W / m2 (without thermostats) W / d size, m m 2 Section power, W IQ

Underfloor heating in rooms Heating mats solutions for all Heating cables Temperature controllers Electric underfloor heating is the most useful heating system for humans. Vertical

ELECTRIC HEATED FLOOR, FEATURES OF SELECTION AND INSTALLATION GENERAL INFORMATION Underfloor heating is a system that allows you to heat an apartment, a country house, a public building due to infrared radiation

T S I L S Y PRAYAN 2019 AND FEET WARM, AND FINANCE IN ORDER IQ FLOOR MAT simple and convenient solution, intended for installation directly into a layer of tile adhesive (up to 10 mm high), for any

STN Company is focused on solving applied problems in the field of heating, using an amorphous alloy strip as a heating element. By operating the heating systems of our company, you get,

0 FLOOR HEATING Comfortable and uniform heat Underfloor heating is suitable for almost all types of flooring and is a great solution for all types of buildings. Floor heating is hidden from view and gives

For decorative coatings: Laminate Parquet board Carpet Linoleum Assortment Film heat-insulated floor Slim Heat Heat-insulated floor Slim Heat is designed to create a comfortable or basic heating of a room

Underfloor heating Introduction Contents Introduction ... 2 Products - TL Series ... 3 - MB Series ... 4 HEATUS cable systems are designed for heating stone and tile floors in bathrooms, kitchens, hallways and others

Infrared or film underfloor heating is a modern type of electric underfloor heating, which is manufactured using the most advanced technologies. Its installation takes a little time and does not require

Build on Uponor with More comfort in any room with Uponor Comfort E Uponor Comfort E our new fast response heating solution that improves comfort in the most privileged areas

DAEWOO ENERTEC retail price, January 2019 Catalog boilers, XL PIPE ONE STEERING ON SEPTEMBER 2019 ONE STEERING STANDARD XL PIPE Energy: Power: 40 W m Length of systems from

E I Simple Heat SERIES (12W) With built-in thermostat ANTI-FREEZE DOMESTIC PIPELINES NEW! INSTALLATION AND OPERATING INSTRUCTIONS SECTION HEATING CABLE FREEZSTOP SIMPLE HEAT Manufacturer:

Heating mats devimat DSVF PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official conclusion of the Central State Sanitary and Epidemiological Service on hygienic assessment. Content of the "Passport"

Installation and operating instructions for the Tropix underfloor heating system IMPORTANT! For thermostats manufactured by OOO "SST", the temperature sensor is connected to terminals 1 and 2; supply voltage (variable

HEATED FLOORS LAVITA COMFORT AND COMFORT OF YOUR HOME! www.rosizol.com; www.stroydostavka.com Lavita heating cables are high quality products that are designed and manufactured in South Korea using

Heat from below. How much does underfloor heating cost? Today you can not expect favors from nature and utilities thanks to a modern and reliable underfloor heating. This system is installed in an apartment, cottage, on

Water heaters Gas instantaneous water heaters We thought about people who are not used to limiting themselves in anything, and in matters of water supply rely on reliable and modern solutions, such as

Electric underfloor heating is a type of modern heating that uses electricity to generate heat. It does not require the installation of pipes and circulation of the coolant through them, therefore it is not afraid of low temperatures

Room thermostat Veria Control ET45 Veria is a European manufacturer of electrical floor heating systems. The company was founded in 2006 in Denmark and currently operates in 16 countries.

General information Heat-Pro Range MiniKit 3mm Heating Cable Kits are the most flexible and economical solution floor heating. 3mm ProRange MiniKits are designed for use in small

Underfloor heating Heating cables and mats, thermostats and accessories Ensto underfloor heating is: comfort safety environmental friendliness economy Finnish quality Ensto fits your home: For basic

STEERING STEADY-ON-OFF-ON-OFF-ON-OFF-ON-OFF-ON-OFF-2018-ON-A-ON-A-ON-A-OUT 2018 XL PIPE Power: 40 W / r. m System length from 7 m to 84 m Supplied in finished form, in coils Installation in a screed 4 5 cm TILES / LINOLEUM

Frost protection for household pipelines installation and operating instructions KPR.00047.01 IM heating cable section freezstop simple heat Economical and safe solution for your comfort

ANTI FREEZE PROTECTION OF DOMESTIC PIPELINES INSTALLATION AND OPERATING MANUAL KPR.00047.01 IM SECTION HEATING CABLE FREEZSTOP SIMPLE HEAT ECONOMICAL AND SAFE SOLUTION FOR YOUR COMFORT

Thin heating mats 3 Self-adhesive heating mat 3 mm thick for installation under ceramic tiles or natural stone. What mat do I need? -90 For well insulated floors. When using the system

FLOOR HEATING Comfortable and even heat Floor heating is suitable for almost all types of flooring and is an excellent solution for all types of buildings. Floor heating is hidden from view and gives freedom

HEATED FLOORS ELECTRIC GOODS 1. WHAT IS HEATED FLOORS? Underfloor heating is a heating system that provides floor heating in the room. It is a modern and convenient way to heat a living space or house at any

V recent times warm floor is gaining popularity. It serves as the main heating of residential buildings, as well as additional comfort floor heating. Since warm air rises upwards, then at

Installation and operating instructions for the MiNi underfloor heating system IMPORTANT! For thermostats manufactured by OO "SST", the temperature sensor is connected to terminals 1 and 2; supply voltage (variable

Cable heating systems LAVITA cable floor heating systems are a reliable and practical solution to the problem of heating your apartment, office, cottage, garage. The LAVITA underfloor heating system is very easy to use,

Heating cable deviflex DTCE PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official statement of the TsGSEN on hygienic assessment. Content of the "Passport"

DEVImat DEVIrail DEVIreg DEVImat DEVIreg For cable products, DEVImat is provided with a 20-year warranty, for DEVIreg Touch thermostats 5 years, for thermostats 2 years. (bathrooms, toilets, refrigerators

DEVI products Deviflex heating cable two-core Two-core cables: DTIP-10 (10 W / m) DTIP-18 (18 W / m) DTIE-10 (10 W / m) DTIE-17 (17 W / m) lengths from 2 to 200 m P - XLPE cross-linked polyethylene (inner

Heating cable deviflex DTIV-9 PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official statement of the TsGSEN on the hygienic assessment. Content of the "Passport"

LET'S SHOOT "XL PIPE" LET'S LET'S GETTING STARTED TO THE XL PIPE? The unique electric-water heat-insulated floor XL PIPE is a pipe with a diameter of 20 mm

Enhancing energy savings with electrically heated glass Thermo Glass is an electrically heated glass created with an innovative patented technology. Operating principle: low-emission

Heating mats Devimat DTIR PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official conclusion of the Central State Sanitary and Epidemiological Service on hygienic assessment. Content of the "Passport"

Www.teplokomfort.com is the official exclusive dealer of Dayol in Ukraine. Dayol company since 2007. is engaged in the production of infrared film underfloor heating. All these years the company has been accumulating

Heating cable deviflex DTIP-10 PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official conclusion of the TsGSEN on hygienic assessment. Content of the "Passport"

Warm floors Chuvashteplokabel. Distribution map. More than 30 distributors throughout the Russian Federation (Cheboksary, Moscow, Vladivostok, Volgograd, Voronezh, Yekaterinburg, Izhevsk, Yoshkar-Ola, Kazan,

Energy efficient underfloor heating T2Reflecta 2 Energy saving underfloor heating T2Reflecta System components Self-regulating heating cable T2Red. T2Reflecta Inserts: Mounting Slots

SELF-REGULATING HEATING CABLES SELF-REGULATING CABLE TYPE MLTV Heating cable design Description Self-regulating heating cable type MLTV used for frost protection

Heating cable deviflex DTIE-10 PASSPORT The products are certified by the GOSSTANDART of Russia in the GOST R certification system and have an official statement from the TsGSEN on the hygienic assessment. Content of the "Passport"

HEATING SYSTEMS 26 Heating mat "Comfort" Thermoregulator mtt-1 Thermoregulator ett-1 p. 774 p. 777 p. 777 - hit of sales - new - made in Russia 773 Heating mat "Uyut" EKF PROxima DESCRIPTION

Protect your house from snow and ice Ready-made kits for protection from ice, icicles and accumulation of snow masses. Freezstop Roof for roofs and drainage systems. Freezstop Patio for steps and outdoor areas.

RU Installation Instructions for installation. Thermostats Devireg 530, 531 Devireg and 532 TM 530, 531 and 532 Article: 08095837 Version: 01.01 1 2 Description and functions Description and

IQWA Inc., CANADA 20 W / m ECONOMIC HEAT! IQ Floor cable Heating cable Installation and operating instructions IQWA Inc., CANADA We are glad you did right choice in favor of IQWA. In our

Stainless steel www.energyrus.ru Advantages Self-assembly is possible, no need to call a plumber and cut off the water. Polished stainless steel- will not fade or peel off. LEAKAGE

Installation and operating instructions for the floor heating system Standart IMPORTANT! When connecting the sections, pay attention to the colors of the insulation of the conductors of the installation wires, where the yellow-green wire is ground or

EL-RAIL, EL-POINT SOLUTIONS FOR HEATING RAILWAY RAILS AND POINTS Electric heating system In areas with long winter periods, any outdoor surface is covered

IQWATT Inc., CANADA 20 W / m ECONOMIC HEAT! IQ FLOOR CABLE HEATING CABLE INSTALLATION AND OPERATING MANUAL IQWATT Inc., CANADA We are delighted that you have made the right choice with IQWATT.

Even the ancient Romans knew about keeping your feet warm. They provided for special systems in the floors and walls of public baths and in their households, which served for heating. These were special ovens that were erected outside the building. When they were kindled, warm air flowed through a branched system of channels into each room. At the same time, all rooms of the building were heated very efficiently.

A similar principle is used today. Only modern systems have a completely different design. For example, warm floors "Electrolux". With their help, you can effectively heat a surface made of any material. In this case, the use special technologies does not allow the creation of vortex flows, which contributes to the correct distribution of heat in the room.

Modern designs

Nowadays, builders no longer build stoves, which were so popular in ancient Rome. Today, floors can be heated using a special heating system, the main element of which is the electric cable. In addition to high efficiency, such a design is distinguished by a great opportunity to save energy resources.

Cable systems are the best option for city apartments. They allow you to find the golden mean between the complexity of the installation and the price. It is worth noting that floor heating systems in which a heat transfer fluid is pumped cannot give the same effect as electric ones. Indeed, in the latter of them, a more comfortable distribution of the available heat flows is provided. In addition, these systems emit a small amount of dust that rises during conventional streams. This is very important for someone who suffers from allergies.

In the design of any underfloor heating system, sensors are provided, as well as devices that control the temperature. This allows you to achieve substantial savings energy resources.

Types of warm floors

Electrical systems for heating floor surfaces can be cable, rod and film. The difference between these types lies in the complexity of installation. In addition, they are laid on different bases. In principle, these floors can be either convection or infrared. It all depends on what type of heating element is provided in their design.

Electric cable floors intended for heating are produced in different types. These are, as a rule, special mats, sections or a cable located on a reel.

The main elements of the system

Warm floors "Electrolux" are built using a two-core cable, which is one of the main components of the system. However, in addition to it, such structures contain other important components. So, according to experts, when installing underfloor heating in a room, it is better to select and install separate thermostats. Such devices will guarantee a comfortable use of the system.

The thermostat or thermostat is designed for one function. He is responsible for turning the heating element on and off, as well as maintaining the temperature set by the user.

Industry Leader

Many buyers know the company "Electrolux" for household appliances, which are distinguished by the highest level of quality. However, the release of various devices to facilitate household work is not the only direction in the company's activities. This manufacturer has been considered one of the leaders in the market for various electric heating systems, including underfloor heating, for fifteen years. The company offers consumers a fairly extensive range of models produced by it.

Warm floors "Electrolux" are presented in different options... Among them are cable sections and heating mats, which, according to user reviews, can significantly simplify installation work. In addition, the company offers its customers a large series of "Electrolux" thermostats for underfloor heating.

Innovative cable

Warm floors "Electrolux" have a number of advantages that distinguish them favorably from similar products of competing firms. The experience accumulated by the company, used in combination with innovative technological achievements, has allowed its specialists to create a unique series of products that sets a new level of comfort and quality.

One of the advantages of the electric underfloor heating "Electrolux" is the use in its construction of a super-strong core made of aramid threads. This core is the base of the heating cable.

Aramid is a synthetic fiber with high thermal and mechanical strength. This material is used in the manufacture of fire retardant clothing, body armor, as well as for reinforcing tires. Such important areas of application of the armide were chosen due to the fact that it is five times stronger than steel.

How does this material work in a cable? Armide cores significantly increase its resistance to tensile loads, kinks at bends and breaks. For example, such a cable will not be damaged even if a breaking force of 200 N is applied to it.

Use of durable insulating materials

What else favorably distinguishes the warm floor "Electrolux"? The experts' comments indicate that the company chose fluoroplastic as the material for the insulation of its heating veins. It is distinguished by a wide range of mechanical properties, high electrical strength, and low wear rates. Fluoroplastic insulation has the highest characteristics of reliability and safety, which makes it possible to increase the resistance of the cable to local overheating.

Innovative textile backing

Reviews of experts who install and maintain underfloor heating "Electrolux" indicate another important advantage of the systems of this company. This is the use of a unique textile backing for the heating mats. This base is impregnated with a special adhesive that prevents the formation of air bubbles in the mat.

Heating cable threads are woven into the unique textile. This ensures the creation of a uniform mat structure.

Installation features

According to experts, it is not at all difficult to install an underfloor heating "Electrolux". The instructions attached to such a system say that for laying the heating mats it is not necessary to pour a concrete screed, and also calculate the laying pitch and cable power. At the same time, special knowledge is not needed. When installing underfloor heating "Electrolux", you just need to determine the heating area and choose the most suitable model for the room.

Another advantage of heating mats from the company is the uniform and fast heating of the entire floor surface, as well as self-fixation of the installation due to the adhesive layer.

Simplicity and savings with the Easy Fix Mat

This series is the simplest and most profitable solution when organizing warm floors. The Easy Fix Mat uses a thin two-core cable.

How is the installation of this "Electrolux" warm floor carried out? Reviews of experts and owners who make repairs in their apartment on their own indicate that the installation of such a system does not cause any particular difficulties. To arrange a warm floor, simply unfold the mat, and then fix the floor covering with a self-adhesive base. At the next stage, the instruction for the warm floor recommends checking the resistance that the heating cable has, and only then connect the system to the thermostat.

Next, an adhesive solution is laid on such a system, on top of which a floor covering is arranged. Such a warm floor-mat "Electrolux" is ideal for those rooms in which it is necessary to equip floors with a minimum rise in level (up to 10 mm). The company offers a wide range of models in this series, which will allow you to heat a small room, the area of which does not exceed 12 square meters.

Install Easy Fix Mat - "Electrolux" warm floor - under the tiles, as well as under the natural stone, using tile glue. The arrangement of such a system is also possible in those rooms where laminate, carpet, linoleum and parquet are used as flooring. In this case, the heating system must be laid on a screed.

Elastic Multi Size Mat

This underfloor heating model is an innovative solution from the Electrolux company. The basis of this design is stretching textiles, thanks to which the length of the mat can be changed from 10 to 35 percent of its parameters. The uniqueness of this design provides the ability to adjust the paving area and system power. By stretching and bending the Multi Size Mat, you can also change the way the mat is laid. For example, it can be not only the usual rectangular, but also trapezoidal, diamond-shaped, etc.

At the same time, a warm base can bypass any obstacle without any problems. According to user reviews, this property of a warm system is very convenient for installation, which is carried out in rooms that are non-standard in terms of their parameters. This can be, for example, bathrooms, hallways and kitchens equipped with stationary large-sized appliances.

Lay this warm floor "Electrolux" under the tiles. User reviews say that even in cases where the shape and area of laying differ from those planned in advance, this will not cause any problems for such a structure, because the Multi Size Mat underfloor heating can stretch up to thirty-five percent of its original length. In this regard, the power of the system, calculated per unit area of the room, will also change proportionally. This allows you to lay such a warm floor "Electrolux" under the laminate and other floor coverings.

Cable sections

This is another of the classic varieties of warm floors from the Electrolux company. As a rule, the cable sections are laid in a leveling concrete screed. Such an installation is carried out at the stage of major repairs or construction.

Cable sections are used in rooms with complex configurations. According to their technical characteristics, such warm floors allow laying the heating cable with a certain pitch. This allows you to set required power construction, which can range from 120 to 200 watts per square meter.

One of the models of the cable section is Twin Cable underfloor heating. According to experts, it can be considered a real full-fledged heating system. One such section is quite enough to create the most comfortable microclimate in the room.

The main difference between the Twin Cable system and existing analogs lies in its cable. It is based on two veins, both of which are heating. In addition, the stress arising between them is distributed quite evenly. Due to this feature, the consumer receives an efficient and quick heating of the room, and due to the minimum load - low energy costs. The heating rate of the room is also quite high when arranging the cable section.

Thermostats

As one of its key missions, Electrolux sees the solution to the issue of simple and comfortable control warm floors. The only visible part of the system is the thermostats. With their help, you can control the warm floor.

The highest achievement of the company is the line of the Thermotronic series of thermostats. It includes:

1.Thermotronic Basic. This is a series of underfloor heating "Electrolux" with mechanical control. A floor temperature sensor is included with the device. The Thermotronic Basic thermostat has the ability to set a minimum and maximum temperature limit, keeping the set parameters at a constant level.

2... Thermotronic Avantgarde. This is a stylish series of electronic programmable thermostats equipped with a round LCD display. The rubberized buttons located on it, pleasant to the touch, allow you to set any temperature conditions in the room, depending on the time of day and even for every hour.

3... Thermotronic Touch. The company has equipped the programmable thermostats of this series with a touchscreen display that can be programmed for a week with the ability to set six time periods during which you can set different temperatures. The device has a lock function that protects the display from accidental pressing.

It is worth emphasizing that the “Electrolux” underfloor heating regulator and all other products of the company have been certified in accordance with international European standards and safety requirements. At the same time, the manufacturer has established a warranty period for thermostats - three years, and for heating mats - twenty years.

And slippers. This trend persists even where the temperature exceeds 20 degrees, because modern radiators cannot provide full heating of the room. But progress does not stand still, and today the use of the "Electrolux" warm floor system allows you to forget about the cold flooring in your room forever.

Warm floors of a new generation from "Electrolux"

For more than 10 years, Electrolux has been offering its customers innovative heating solutions based on a heating cable, occupying a leading position in the global underfloor heating market for many years. The Electrolux range for comfortable underfloor heating includes unique heating mats, cable sections, state-of-the-art thermostats, as well as professional options for heating pipes, de-icing gutters, roofs and platforms. According to reviews, this is the best warm floor.

Electrolux heating mats

They are the fastest and in a simple way creating a floor heating system that is accessible even to non-professionals. For the installation of the mats, pouring a concrete screed is not required, there is no need to calculate the pitch and power of the cable laying, so you can install the heating mat in the room yourself by spreading the roll over its area. An electrician is only required to connect the system to the network. Electrolux heating mats are presented in two series:

The EASY FIX MAT series is a self-adhesive heating mat based on a two-core thin cable of 150 W / m, securely woven into a textile mesh impregnated with a special adhesive. It fixes the mat to the floor and creates ideal conditions for adhesion to tile adhesives and concrete. Recommended for installation without screed.
The MULTI SIZE MAT series is an ultra-thin elastic heating mat. Its unique stretchable design allows you to change the length of the mat, so you can vary the heated area and power of the mat, as well as lay it with a turn. Installed under any floor covering, including wood. Perfect for creating a heated surface with irregular geometry (corner corridors and balconies, bathrooms and kitchens).

Heating sections "Electrolux"

TWIN CABLE cable sections are classic options for electric underfloor heating. They consist of a 17 W / m2 2-core cable. Sections are ideal for floors with non-standard complex configurations. They can be installed in tile adhesive, concrete or under a stone.

Thermoregulators "Electrolux"

Thermostat is a control unit for underfloor heating. Its purpose is to control many functions and heating modes in the system. The Electrolux range includes a temperature sensor for underfloor heating with electronic, mechanical and touch control.

Advantages

Warm floors "Electrolux" have a number of advantages, the main of which are:

Fast and even heating of the entire area in the room. Due to the fact that the heat flow is directed over the entire area from bottom to top and the heat distribution occurs in the vertical direction, a natural feeling of comfort is created.
Compared to such heat sources as radiators, stoves, convectors, fireplaces, warm floors "Electrolux" create much less drafts, convection flows, and form less dust in the air.
In the system, the only visible element is the thermostat. The heat source itself is hidden under the floor, which frees up space for various interior items and furniture.
Due to the fact that there is no direct contact of the heating elements with the atmosphere, the air does not dry out, and the humidity in damp rooms (bathrooms, hallways) is regulated.
Automatic maintenance of the set temperature. The heating mode is programmable, so that energy consumption can be reduced by 2 or more times.
Durability. The service life of the electrical heating cable system is 50 years or more, and does not require maintenance.
Warm floors "Electrolux" are resistant to heavy physical exertion.

Mounting

As practice has shown, the most optimal and affordable way to make your flooring warm is to use heating mats with a base of thin cords, which are fixed on a self-adhesive base. Their installation is very simple (no concrete screed is required), no special skills or knowledge are required.

Before you start laying the system, you should prepare the place where the temperature sensor for the underfloor heating will be installed. What needs to be done next is simply to unfold the mat and fix it. Then check the resistance of the cable and connect the Electrolux thermostat. Next, put this coating on and enjoy the warm floor.

Common installation mistakes

Despite the fact that the installation process is very simple, some problems are not excluded here. The main ones are:

getting nails into the heating cord;
incorrect connection in the thermostat contacts.

In case of any problems during installation, it is recommended to contact any service center of the company.

How much does a warm floor cost?

Due to the high demand for underfloor heating, they can be purchased in almost all specialized stores, however, in order to be 100% sure of your purchase, it is best to stop the choice precisely at those enterprises that have recommended themselves only from the good side. How much does a warm floor cost? The minimum price is from 2290 rubles.

The fact that the feet must be kept warm has been known since the days of Ancient Rome. Then, in public baths, as well as in private households, the floors and each room in the room were heated using special systems. It was a stove that was located outside a residential building. From it, warm air passed through a system of channels under the floor, as well as into the walls. Thus, all rooms from all sides were very efficiently heated. This principle has not been forgotten and is used now, but modern systems have a slightly different design. For example, a modern underfloor heating from the Electrolux company very effectively heats any floors, and the use of special technologies prevents the creation of vortex flows and allows you to distribute heat in the room more correctly.

Modern warm floor

Nowadays, they no longer use the stoves, which were once popular in ancient Rome. Today, for floor heating, a heating system built into the floor is used, based on a special heating electric cable. In addition to the high efficiency of such a system, it has great potential for saving energy resources.

Most apartments use cable systems. For urban conditions, they are the most optimal. Here you can trace the golden mean between the price and the complexity of the installation. As for comfort, there are practically no competitors here. With the help of a heat transfer fluid that is pumped through pipes, it is very difficult to achieve the effect that electrical systems give.

Warm floors allow for a much more comfortable distribution of heat flows. While the radiators central heating heat the air, and it then goes up, the heat from the floor remains below, and then rises to the level of the human head, thereby creating optimal conditions for a person. Also, among the advantages, a smaller volume of dust is distinguished, which rises as a result of the action of conventional flows, which is important for those who suffer from allergies.

Underfloor heating systems are equipped with sensors and temperature control systems, which can significantly save on energy resources. When using such systems, an average of about 20% of electricity is saved.

Features of electric underfloor heating

There are several types of floor heating systems. So, there are cable, rod and film models. The difference between them is in the complexity of installation, as well as in the base where they will be laid. As for the principle of operation, these are either convection or infrared heating elements.

Electric cable floor with heating is often produced in the form of special sections, mats, or in the form of a cable on a reel. When making a choice, many people face the question - which cable is the most optimal?

There are two types of cable used. It can be one- and two-wire. To answer the question, which cable is better, you need to understand a little.

The element can be ordinary (resistive), with a constant very high level of resistance. Its main task is to convert electricity into heat. Naturally, any cable in one way or another, but converts part of the electric current into heat, but this is only about 3%. Heating cables are capable of converting about 100% of electricity into heat energy. Also, some systems use a self-regulating cable. It has special properties due to which it can regulate the current passing through it.

As a single-core cable, and a two-core cable have almost the same efficiency. For example, Electrolux offers floor heating built on a two-core cable.

System components

In addition to the cable, such systems have other equally important components. These are the thermostat and sensors. Experts recommend choosing and installing separate thermostats for different rooms. This ensures a more comfortable use of the system.

The thermostat or thermostat has one function. He is responsible for turning the heating element on or off. It is also designed to maintain the temperature set by the user. At the right time, the device, based on the data received from the sensor, will turn on or off the heating element.

Choosing a thermostat for a warm floor

There are only two types of these devices. So, there are simple devices or with the possibility of programming. Before choosing, you need to decide whether there is a need to automatically turn on or off the heater according to a given program.

Simple devices can only do primitive things - turn on or turn off the system. Often, this functionality is quite enough for comfortable operation. The user will independently turn on the equipment. Depending on the cable used in the system, the heating time can take from 15 to 20 minutes. These devices do not have the ability to disconnect the cable or reduce the operating temperature at night or when the user is not at home - these functions are programmable and they can significantly save.

Equipment from the industry leader

Electrolux is known to many for its high quality household appliances. But this is not the only area of work. For 16 years now, this manufacturer has been confidently holding its leading position in the market of underfloor heating and other electric heating systems.

The company already has a fairly wide range of models. Warm floors are presented in different options... So, both cable sections and heating mats are offered, which greatly simplify installation. The company also released a large series of thermostats.

Advantages of systems from Electrolux

A real breakthrough in technology, as well as extensive experience, allows the company's engineers to create high-tech equipment that can significantly increase the level of comfort in apartments and private households.

The cable core from this brand is very durable. Aramid threads are used as material. It is a special high-strength synthetic fiber. Steel is 5 times less durable than aramid. The material is used for the production of body armor, in the production of car tires and much more. This material significantly improves the performance of the cable.

The core insulation is made of fluoroplastic. Here, high wear characteristics, as well as fluoroplastic, are distinguished by high electrical strength. This isolation ensures maximum reliability even in the event of significant overheating.

The base of the heating mat is created on the basis of a unique textile material. It is also impregnated with a special adhesive for added strength. This ensures not only strength, but also excellent adhesion in the screed. The structure of the mat is homogeneous.

The lineup

Among the many options for organizing a warm floor, Electrolux specialists offer heating mats as an ideal option. These mats are based on very thin electrical heating elements.

When installing such systems, there is no need to pour the screed. Also, the installation does not require any special knowledge or skills. These mats can be installed under absolutely any floor coverings. Also, the absence of a screed will not steal space in the room. For installation, you just need to correctly calculate all the parameters, and then, based on the results, you should select a set of necessary and suitable equipment.

Not only engineers recommend Electrolux underfloor heating. Users leave positive reviews about the systems of the company. So, the reviews talk about the rapid heating of the floor surface, as well as the ease of installation due to the self-adhesive mat.

EasyFix Mat: simplicity and economy

According to the manufacturer, the EasyFix series of systems is one of the most economical and profitable solutions for the organization of "warm floors". The series is represented by a two-core thin cable.

Installation is easier than ever. It is enough to unfold the heating mats on the required surface and fix them securely. There is a special composition for this. Then it is recommended to check the integrity of the structure using a multimeter, and then, if everything is in order, you can connect the warm floor to the thermostat. Next - you can start installing floor coverings. This system does not take up much space - the floor will only rise by 10 mm.

Innovative textile base Multi Size Mat

The solution is created on the basis of a special stretching base made of textile materials. This unique material allows the mat to change its length by up to 35%. Also, this design allows you to adjust the power and paving area. In addition, the shape can also vary. This is very important when there are various obstacles in the form of thresholds, furniture or built-in appliances on the way of the warm floor.

Cable sections

Electrolux also offers cable equipment. These sections are designed for installation in a concrete screed. The series of systems is perfect for rooms with complex configurations. The installation process takes place with a certain laying step. You can also adjust the power of the warm floor.

One such section is Twin Cable. This, according to the manufacturers, is a real complete heating system. It alone is enough to create the most comfortable microclimate in the premises. The difference between this system is in a special cable. Both cores heat up, and the voltage between them is evenly distributed. What does the consumer get as a result? Efficient heating with minimal energy consumption. Also, the heating rate with such sections is quite high.

Thermostats are the only part of the system that can be seen and used. All devices from the company have a nice design and a wide range of functions. Engineers have created several series of equipment. Thermostats are equipped with all the necessary sensors and light indication.

In all series, except for the initial one, the thermostats are equipped with a display on which all system parameters are visible. Intelligent algorithms are also implemented in the device. Any parameter can be programmed.

Whatever consumers choose, any type of Electrolux products is invariably high quality and safety. Any equipment is fully certified, and the warranty for underfloor heating systems is 20 years.

Such systems are very cost effective. In this they differ significantly from traditional heating appliances... Warm floors are chosen for their high comfort, simplicity and reliability. And underfloor heating from Electrolux is chosen for its excellent quality from professionals and industry leaders. Feedback from users has already confirmed the excellent performance of the equipment.