How to make a convenient workbench in the garage with your own hands. Do-it-yourself workplace organization - garage workbench: photos, drawings and table dimensions Do-it-yourself workbench in the garage drawings

Everyone knows that a garage is necessary in order to put a car in it. However, many car owners use this room as a warehouse for unnecessary things, and if space permits, they remake it into a small workshop. Therefore, appropriate equipment is installed in it - racks, shelves and a workbench. The latter is a multifunctional desktop used for processing various materials, implementation of plumbing, assembly and electromechanical works. Workbenches for the garage can be made by hand.

Garages are predominantly rectangular shape, therefore, when choosing a place for a workbench, certain features of the use of the future workplace should be taken into account:

If the width of the garage is sufficient, then one of the long walls of the building will be the best place for the workbench, as this will allow you to make the table of the desired length and provide access to the workbench from three sides, which is very convenient, especially in the case of simultaneous work of two people;
If the workbench is installed at the end of the garage, you can take out all the fixtures for the vise and other fixtures on the front of the tabletop, distributing holes for clamps and other tools along the front longitudinal side of the table;
Another option for the location of the workbench is along a long wall with an emphasis on the end wall, which makes it possible to use the approach to the table from two sides.

Advice! If on the side of the workbench adjacent to the wall to strengthen vertical racks with crossbars, you can conveniently place on hooks or other types of holders various tools that will always be in sight.

The first experience of building equipment for the garage can be a simple wooden workbench or a wooden workbench. The design of a table made of timber is more affordable to manufacture, working with a saw, a jigsaw and a drill is much easier than cutting and welding a steel corner, from which professional quality locksmith tools are usually made.

We build a wooden workbench for assembly work

To build a workbench, we need:

Wooden beam, preferably oak or pine, about 12-15 m, the material section is selected individually, based on the expected load on the workbench;
Edged planed board, 20-30 mm thick, smooth, without knots and surface defects;
Sheet plywood, 6-8 mm thick, three canvases 200x60 cm;
A set of self-tapping screws for wood and steel corners, shelf size 50 mm and length from 50 to 70 mm, at least 40 pieces.

Advice! All cutting work must be carried out using a manual or stationary circular saw, cut the edges of the timber or boards only with a jigsaw or similar power tool.

In this case, even in the absence of carpentry skills, the cut is even, respectively, the entire design of the workbench will look like a factory one.

At the first stage, we make the frame of the workbench, while taking into account the dimensions of the place in the garage. To do this, you will need to cut four vertical posts, four horizontal beams and five horizontal short transverse struts from the timber. If the dimensions of the wooden workbench for the garage do not exceed two meters, you can use a bar with a section of 70x70 mm.

We cut off four vertical racks - two 90 cm high, two 150 cm each. The latter are made 60 cm higher, after the workbench is assembled, a plywood screen will be installed on them for the tool stored in the garage.

Horizontal beams too different size. To bandage the support posts of the frame in the lower part of the workbench, we cut off two sections of a beam of 150 cm each, to fix the tabletop, sections of 200 cm are needed. The last of the remnants of the material we cut the transverse struts 60 cm long.

We assemble the entire structure using steel corners and self-tapping screws, as shown in the diagram.

We assemble the tabletop by gluing together from plywood sheets and boards. After leveling and adjusting the dimensions of the boards and plywood, smeared with PVA-M or wood glue, we assemble in clamps until completely dry and cured. We sew the countertop along the contour with self-tapping screws.

We lay the tabletop on the finished frame and fasten it with self-tapping screws, after which the surface is carefully polished with an emery nozzle for an electric drill. We install the screen last and cover the entire structure with varnish so that in wet weather in the garage the wood of the workbench does not “lead”.

In appearance, the workbench for the garage turned out to be quite openwork, but in reality its strength is enough to withstand a load of more than one hundred kilograms. To increase rigidity, the rear racks can be anchored to the walls of the garage.

Required tool:

Bulgarian with a circle for cutting metal and a grinding disc.
Welding machine and electrodes.
Overalls and protective devices for welding.
Level.
Roulette.
Screwdriver.
Jigsaw for cutting plywood.
Drill.

Necessary materials:

Corner 50 mm by 50 mm, thickness 4 mm, length 6.4 m.
Square pipe 60 mm by 40 mm, thickness 2 mm, length 24 m.
Corner 40 mm by 40 mm, thickness 4 mm, length 6.75 m.
Steel strip 40 mm wide, 4 mm thick, 8 m long.
Steel sheet for countertop 2200 mm by 750 mm. Thickness 2 mm.
Steel sheet for making drawer holders. Thickness 2 mm.
Wooden boards for countertops. Thickness 50 mm.
Plywood for the manufacture of drawers and for the side and back walls of the table. Thickness 15mm
Guides for drawers.
Screws for assembling plywood boxes.
Self-tapping screws for metal.
Anchor bolts.
Paint for wood and metal.

The workbench, which will be made from these materials, has quite impressive dimensions: the table is 220 cm long and 75 cm wide. The overall design and large tabletop allow you to place a vice and, for example, emery or other tools at different ends of the table.

First step making a workbench is cutting the existing material into elements. The profile pipe is intended for the manufacture of the frame. The steel corner is designed to create stiffeners. It is cut into pieces and a power frame is formed from it. Also, a steel corner is needed for edging the tabletop on which the boards will be laid. The steel strip is intended for the manufacture of guides on which the side panels will be attached. Also, this material will go to the brackets for attaching boxes and plywood. Table drawers are made of plywood.

Second step- welding power frame workbench. The elements of the countertop are welded first - 2 pipes 2200 mm long and 2 pipes 750 mm each. The frame must be welded so that another frame of corners can be welded on top of it, into which the tabletop boards will be laid. To reinforce the countertop, it is required to weld a few more after 40 cm steel pipes, which will act as stiffeners.

Then 4 side legs are welded along the edges of the workbench. Their length is 900 mm. Power jumpers are welded between the legs, strengthening the structure.

After the base frame is ready, you can start welding the structure for the boxes. To do this, square frames are formed from steel pipes, which are welded to the tabletop on both sides of the table. Frames are reinforced with longitudinal stiffeners.

Third step- Making a frame for the tabletop. Two steel corners, 2200 mm long and two more corners 750 mm long, are needed to make the frame. The structure is welded so that wooden boards lie inside it.

The frame from the corner is laid on the frame of pipes and welded. It turns out a reinforced tabletop, 8 cm high with internal stiffeners.

The metal frame of the workbench is almost ready, it remains to weld the crate of the panel for attaching the tool. This requires one metal corner with a length of 2200 mm and 4 corners with a length of 950 mm. Two elements are attached to the sides of the structure and two in the middle, for reinforcement. The toolbar is welded to the worktop.

The frame of the corners and pipes is ready. You can start strengthening the structure. Brackets are welded to the sidewalls of the table, which are cut from a steel strip. A total of 24 parts are needed. A hole is drilled in the middle of each bracket. Through these holes, the side and rear walls plywood tables will be attached to the metal frame of the workbench.

Fourth step- production of boxes for a table. Plywood is cut into blanks, which are twisted with screws. The number of drawers depends on what will be stored in the table. If the details are small, then 3 boxes can be built, if large - then 2. It all depends on personal preference.

You can place drawers on two sides of the table, you can mount pull-out structures on one half, and ordinary open shelves on the second.

After the drawers are assembled, metal strips with holes need to be welded between the sides of the drawer compartments. Slides for drawer guides will be attached to these holes on the inside.

Fifth step- laying boards in the frame of the tabletop. Boards with a thickness of 50 mm are cut into blanks of a certain length. If a long board is available, then you need three blanks 245 mm wide and 2190 mm long. If there are no long boards available, then you can lay the blanks across the table. For this purpose, wood 205 mm wide is cut into 10 blanks 740 mm long.

Before laying the wood in the table frame, it must be treated with an antiseptic solution. This will protect the material from rotting and damage by beetles.

Then in without fail it is required to paint the entire metal structure of the workbench. This will protect the metal from corrosion. It is best to use a weatherproof and anti-corrosive coating option. Be especially careful when painting welding seams. Drops of metal and irregularities are recommended to be thoroughly cleaned before painting. This can be done using an angle grinder with a metal grinding disc.

After the structure is dry, you can start laying the boards on the countertop. They should not be driven too tightly into the frame. This is due to the fact that the tree tends to expand and shrink with a change in temperature and humidity. It is better to leave a small gap of a few millimeters between the boards. The surface of the wood needs to be sanded, this will make it easier to lay the metal sheet on top of the wood. Boards around the entire perimeter of the table are screwed to the frame with self-tapping screws.

sixth step- fastening of the upper steel sheet. It can be welded to the countertop, but there is wood inside the structure, which can ignite during the welding process. Therefore, it is best to attach the steel sheet with hidden self-tapping screws to wooden planks. Previously, the metal must be painted on both sides with a rust converter. This covering material looks like a transparent paintwork, easily restored and reliably protects the metal from rust. You can also paint the metal countertop with the same paint that covered the frame. It will be beautiful, but over time, the paint may scratch and the table will not look too new.

final step- installation of boxes on rails and fastening of plywood on the side walls, shelves and power shield in front of the table. This work can be called finishing workbench. After work with plywood is over, it must be coated with a compound that will protect the material from exposure environment. Also, do not forget about the design of the power shield for tools. You can attach special hooks or screws to it, to which the necessary things will be hung.

In order to make it convenient to work at the workbench, you can attach a special lamp with a bending stand to the power shield. In this case, you can optionally direct the flow of light to the right place.

Vice is an indispensable attribute locksmith workbench. It is not recommended to attach a clamping tool weighing several tens of kilograms to the tabletop itself. It is best to place a metal gasket between the metal of the table and the tool, 1 cm thick. It is required to drill holes in the gasket for anchor bolts. Then, in the same places, drill holes in the countertop of the same size. The whole structure is fastened with anchor bolts.

Having a workbench in the garage, you can perform repair work on one's own without resorting to expensive car service or utilities.

Ready-made workbenches stand not cheap, and they don’t always fit into the garage, so it’s better to make a desktop for the garage workshop with your own hands.

Before starting work, you need to decide on the type of workbench and choose for your model additional functional fixtures.

Types of workbenches

Workbenches vary in several criteria, including design features, dimensions and other peculiarities:

By destination:
- Carpentry workbench is a special table consisting of a workbench (cover) and a pre-workbench. The basis is two support posts connected into a rigid structure by means of longitudinal bars fixed between them. The lid of the workbench is made from beech or oak wood of deep drying, along the side of the board, an elongated recess is made for folding small tools. Attached to the front of the lid workers vise, and on the back they make a rectangular cutout in which you can move additional vise. Drilled into the tabletop row holes for the installation of clamps or stops required in the work;
- carpentry workbench It has maximum length before 6 m, so that you can fix and process long boards and other lumber. Emphasis for fixing boards complement triangular cut, in which wedges are placed so that the workpiece remains stationary;
- locksmith workbench is a sturdy desktop metal frame, having a thick wooden tabletop sheathed with galvanized steel sheet. This design withstands solvent exposure and other aggressive chemicals, as well as hammer blows and the severity of workpieces;
- Universal workbench basically similar to the design of a locksmith's desktop, but has additional holes in the tabletop and possibility clamping vise with different parties covers;
By number of jobs distinguish one-, two-many workbenches;
For additional features:
- Folding workbenches(with folding parts working surface which is very convenient in small spaces);
- Workbench cabinets with a set of drawers in the underframe.

Material selection

Choosing material for the manufacture of a workbench in the garage, necessary take into account what types of work are most often performed, how many people are involved in the work (if two, then it is better to make the countertop more authentic) and how much space in the garage can be allocated for a workbench.

table base better do metallic by choosing a steel corner for this or profile pipes(square or rectangle in section).

for countertop optimal material is oak board or timber good quality so that the material does not subsequently crack or sag.

Under the lining of the table cover choose steel sheet of sufficient size with galvanization (anti-corrosion treatment of steel will greatly extend the life of the workbench).

Choosing a place in the garage for a workbench

Garages have predominantly rectangular shape, so when choosing a place for a workbench, certain peculiarities use of the future workplace:

If the width of the garage is sufficient, then the best place for the workbench will one from the long walls of the building, as this will make it possible to make a table of the required length and provide access to the workbench from three sides, which is very convenient, especially in the case of two people working at the same time;
If the workbench is installed at the end garage, you can take out all the fasteners for a vice and other devices on the front of the tabletop, distributing holes for clamps and other tools along the front longitudinal side of the table;
Another option for the location of the workbench - along the long wall with an emphasis on the end wall, which makes it possible to use the approach to the table from two sides.

Advice! If on the side of the workbench adjacent to the wall to strengthen vertical racks with crossbars, you can conveniently place on hooks or other types of holders various tools that will always be in sight.

Manufacturing steps

Making a workbench for installation in a garage includes several stages:

Cutting metal parts for the frame, based on optimal sizes workbench (leg height up to 0-90 cm, tabletop length 120 -150 cm, width up to 80 cm);
We weld the frame under the countertop or we connect the parts into a rectangle with bolts;
We weld the legs table to frame;
At the bottom of the legs (approx. 10 cm from floor) fasten safety metal details that will give the workbench stability;
We attach to the frame boards countertops with bolts;
We sheathe the lid metal with self-tapping screws.

Attention! In order for the workbench to acquire maximum stability, it is attached to the garage floor with metal corners.

How to make a workbench in the garage with your own hands, learn from this video:

As a rule, a drawing of a workbench for a garage is necessary only if the free space in the room is limited and it is necessary to make a desktop according to its size. First you need to understand for what purpose you will use it most often:

Minor repairs and minor carpentry work - a table up to 1.5 meters in size is suitable;
You plan to constantly carry out work in the workshop - the necessary long workbench from 3 to 4 meters;
We need constant car repairs and a place for locksmith work - we need to make a full-fledged shelving system and a desktop with drawers.

All homemade workbenches you made with drawings for the garage must meet the following requirements:

Compact design;
Stability of the frame and all elements;
Versatility in the use of any of the equipment;
Good illumination;
Plenty of storage space for parts and tools
Arrangement of several safe places for electrical networks.

We make a workbench in the garage with our own hands with photos and drawings

Garage workbench dimensions

Before starting work on cooking or nailing the desktop frame, you need to approximately describe the parameters and dimensions in the drawing. First of all, the drawing displays the materials for the frame and its dimensions. Next, the thickness and height of the workbench in the garage are planned along with the countertop.

Basically do carpenter's workbench to the garage with your own hands measuring 55 by 155 cm. However, for massive equipment, you can increase the length by 2-2.5 times. A metal corner is fixed along the entire length and a strip of metal is strengthened along the contour of the tabletop.

What should be the height of the workbench in the garage? Usually they plan for a person’s height so that the countertop is at the level of a person’s belt. If you want to make small carpentry, then attach a smaller worktable to the workbench, in which you can sand and saw small parts.

Attention! Now it is popular to invest in a garage workbench with your own hands drawings with automatically adjustable table height. A simple method to determine the height is as follows: lower both hands down and point parallel flooring your palms. It is the height between the palms and the floor that will be the final height of the frame.

Garage workbench dimensions

The garage workbench drawing allows you to display all 3 parameters - the height, width and length of the desktop. The thickness of the countertop is mainly chosen at least 5 cm; an oak or pine board is best suited as a material. The basis of the structure will be a frame made of metal corner, since it is mainly necessary to carry out locksmith and carpentry work.

To achieve the highest stability indicators, it is recommended to make a do-it-yourself garage workbench in the drawing with additional transverse supports. The supporting frame must be at least 4 and not more than 8 meters. Also keep in mind the location of the desktop. The removal of the workbench from the car should be at least 1.5 meters.

The most important thing when planning the dimensions of the workbench in the garage with your own hands, do not forget about the maximum use of free space. Only by correctly arranging all the furniture in the garage can you ensure required level comfort and availability of all repair tools.

Initially the workbench was used exclusively when processing wood, and its main task was to fix the workpiece for emphasis in the use of tools. To do this, they cut holes of various shapes along the edge of the tabletop, hammered wedges, inserted combs and chocks for emphasis or as guides. Such a workbench was called classical.

The simplest design of a workbench looks like this:

supporting frame on legs;
thick tabletop, with a powerful surface;
additional shelf under the tabletop for storing tools and fixtures;
shelves or drawers that increase storage space.

Interesting: Now popular computer game Minecraft, which invites players to create virtual wood workbench from A to Z, in any modification.

Improvement of tools, the appearance of electrical equipment affected workbench modifications. BUT manual processing new material - metal created completely the new kind desktop for locksmith work. So by appointment today workbenches are distinguished:

carpentry;
carpentry;
locksmith;
universal.

Do-it-yourself table in the garage - photo options:

The working table in the garage can be designed for a different number of employees, or zoning places.

In this case, workbenches are distinguished:

single;
double;
multi-seat.

The addition of the capabilities of a specialized workplace has given rise to its varieties:

folding;
mobile (on wheels);
folding wall-mounted workbench;
workbench cabinet (with sections for tool storage).

According to the material from which the work table for processing materials is made, there are:

wooden (made of durable wood);
metal (welded structures);
combined ( wooden base strengthened sheet metal on the table top, complete with combs made of metal, screws with threaded threads; the metal case is equipped wooden shelves and boxes).

Important: The metal parts of the workbench need an anti-corrosion coating, and the wooden parts need an antiseptic impregnation.

What a homemade workbench for a garage looks like, watch the video:

What kind of desktop does a car enthusiast need?

There is not much free space in the garage, so it is important to decide for what goals it will be installed:

minor repairs and minor plumbing work;
a permanent range of work related to home maintenance, or your hobby;
amount of work in car care for full release from the dependence of SRT.

In any case, limited space will require garage workbench:

compactness;
sustainability;
universality;
illumination;
performing a storage function;
safe connection to the power grid;
15 cm above the floor for high-quality cleaning.

Garage workbench dimensions(standard - 6x4) cannot exceed 60 cm in width, and 1.5 m in length. The height of the workbench in the garage is determined based on the height of the owner - to the middle of the hands in a standing position. The best choice will be - metal structure, since most of the work in car maintenance is metalwork. For the greatest stability, it is recommended to support the supporting frame on 6 legs, or even 8.

Location selection- also the specifics of a garage workbench: after all, it should be convenient to work on it with a car standing in the room. And, at the same time, it is recommended to remove it from vehicle not less than 1 meter. With a purchased copy, all these subtleties are difficult to take into account.

We make a workbench for the garage with our own hands - drawings:

If you make a workbench with your own hands, then which one is wooden or metal?

Wooden - easier to manufacture, but ...

The choice of species again determines special purpose: faster and for simple operations - it will be acceptable and wooden frame from a powerful board (40x80mm) or timber (50x100), assembled into a rectangular structure according to standard dimensions, using self-tapping screws or nails. For structural reinforcement use wooden spacers between the legs (top and bottom). The lower ones (at 15 cm from the floor) can become the basis of a storage shelf.

The tabletop is assembled from a planed tongue-and-groove beech (oak) board or two sheets moisture resistant plywood 18mm thick, glued together and sheathed along the edge. For special strength the surface of the tabletop is upholstered with a metal sheet 5 mm thick, making a side from the side of the wall.

However, if you make a wooden workbench in the garage with your own hands, then this option has its drawbacks:

it is not designed for a large force effect;
it is difficult to place several necessary devices on it at once: for drilling, sharpening, heavy bench vise;
the wear of the frame made of wood is short-lived;
the tree deteriorates from spilled oils and paint, fills the pores and cracks with metal dust and shavings;
the risk of fire remains.

See how to make a workbench in the garage with your own hands - photo:

Metal desktop - the right choice

The advantages of a metal workbench for a motorist:

compactness of all structural elements with increased reliability;
the ability to withstand any force;
additional weight for stability;
the ability to take into account the features of the room, making the workbench mobile, folding, folding, shortened;
increased strength of the welded structure;
tabletops can be completely made of metal with a 3-sided rim;
the tabletop does not have sharp corners (for safety);
it is completed with 2 vise and clamping screw;
holes for clamps and stops are provided;
allows you to perform sawing and cutting of metal, turning and grinding;
the ability to fill the space under the countertop with any storage devices (shelves, drawers, organizers, grids);
secure fastening of drawers and shelves;
metal shavings do not clog into slots;
on it it is possible to carry out processing and wooden parts;
safety in conditions of fire risk;
saves the effort of the worker;
This table is easy to maintain.

Note: A metal garage workbench is a hit in specialized stores, where only price and design improvement are of decisive importance.

But the craving for creativity leads along the path of one's own experience.

A useful video on how to make a do-it-yourself garage locksmith workbench:

How to make a metal workbench for a garage?

Algorithm:

Choose a place, taking into account all the requirements for placing a car in a garage.
Prepare a solid base for installation.
Take measurements of the installation site.
Create a sketch of your idea with all the details and improvements.
Prepare necessary material and tool.
Prepare structural elements.
Consider the technology of assembling and strengthening the frame.
Collect product.
Cover with a primer and a protective layer.
Conduct functionality and security testing.
Fix the necessary equipment on the tabletop.

Material required for work:

metal hollow profile (4mm) for legs;
metal equilateral corner (50x4mm) for drawers, prolegs, guides for shelves;
sheet metal with galvanization or stainless steel for countertops (5 or 2mm);
metal strips for edging;
grooved board (50x150mm) for wooden tabletop with metal upholstery (as an option);
self-tapping screws;
primer and paint for metal.

Tool required for the job:

level, tape measure;
drill;
Bulgarian;
welding machine.

Assembly technology:

to assemble the desktop, an integral welded connection of all metal parts is used (sides as the bases of the table top, legs, jumpers, rectangles for stability on the ends of the legs);
horizontal and vertical elements for greater strength are equipped with permanent slopes;
the tabletop is made from a single sheet of metal or a plank shield upholstered with 5mm galvanized iron; in the first case, the tabletop is welded, in the second, it is screwed with screws to the collets and additional metal strips;
for the installation of shelves and boxes, a corner is welded to the racks as guides (boxes can be made of either metal or wood); the tree is treated with an antiseptic;
rectangles welded on the ends of the legs increase the stability of the workbench and allow it to be fixed to the floor.

Do-it-yourself metal workbench in the garage - photo drawings:

Last tip: A do-it-yourself (metal) garage work table should only be done if you are familiar with the art of welding and the safety rules for it in practice.

Do-it-yourself locksmith workbench in the garage is quite simple to make. The main thing is the ability to perform locksmith work: put the correct and reliable weld, work with mechanical and power tools. The work is not difficult, but requires attention and understanding of the operation being performed.

When decorating and filling the garage with equipment, sometimes it seems that building the box itself was very easy, but various little things get out of themselves. But you need to do it, and therefore, before doing the work, it is necessary to sort out some theoretical issues.

Design features

A homemade garage workbench is often positioned with an office desk. With his presence and features, he provides the garage with tools, various parts and equipment:

As a rule, locksmith or machine clamping devices, grinding machines are installed on the tabletop. The countertop itself is made from various materials available to the owner.
The frame is the supporting element of the rest of the device.
Bedside table with drawers for storage of various devices, tools, Supplies. Several bedside tables can be installed not only with drawers, but also equipped with shelves.
It is possible to manufacture additional shelves between the side tables.
We fix a protective screen on the garage wall to protect the painted walls from sparks (when working on sandpaper) and mechanical damage. It can be made perfect place to store locksmith tools and wrenches, and install fluorescent lamps.

Depending on the place for installation and the desire of the customer, the design of the workbench may be different, but its type does not change depending on the equipment.

Varieties of garage equipment

Workbench in the garage with your own hands and in industrial environment perform 2 types:

design intended for a car mechanic;
if you like carpentry in your spare time, this box should be equipped with a carpentry workbench.

A do-it-yourself wooden workbench for carpentry can be made and installed indoors if you need it. If you are not a carpenter, he will only take up space. To perform work related to car maintenance, it is customary to install a metal or wooden structure, but exactly plumbing appointment. It is better to sheathe the countertop with a sheet of steel, you can lay DSP boards. The most stable will metal workbench in the garage.

Instructions for craftsmen

Before work, we will prepare the tool and workpieces.

Advice! The quality of work, the time spent on its implementation, directly depend on the choice of equipment and the ability to apply it in practice. Another important factor is the quality of materials for making a desktop in the garage with your own hands.

Preparatory work

For the manufacture of homemade products, we assemble a tool. The following will help us in our work:

angle grinder with cutting and grinding wheels;
welding machine and welding electrodes(ANO-21, MP-3);
welding mask and overalls;
plumb or level;
5 meter tape measure;
electric drill and screwdriver;
If you have to work with wood, we select a reliable electric jigsaw or a hand saw.

Now we decide on the materials for the manufacture of a workbench for the garage:

First you need to determine the dimensions, make drawings or a sketch. For clarity, let's take the dimensions: length - 2 m, width - 50 cm. Based on these dimensions, we will need to purchase:

steel corner with shelves 50 mm - at least 6 m;
40th corner - at least 8 meters;
profile 40x40, wall 0.15 cm - 24 meters;
steel strip 50x5 - 7 m;
steel sheet, 1.2 mm thick - 2000x500 mm;
board 50 mm for the tabletop, the number depends on the width of the board;
board 25 mm or plywood for shelves and drawers;
MDF or fiberboard as desired, for sewing sidewalls;
Screws, self-tapping screws, paint, primer, drawer guides.

Having finished with the preparation for work, we begin to make a metal workbench with our own hands.

Step-by-step instructions for performing work

Answering the question: how to make a workbench in the garage with your own hands is quite easy. Let's follow a few instructions and rules for the work:

We cut off the blanks of the required length with a grinder.

We prepare 4 longitudinal parts for the frame: a length of 2 meters from the profile and 4 jumpers, their length is 420 mm. From the corners we cut off the stiffeners and jumpers for the shelves.

Let's start assembling the skeleton of a workbench for a garage with our own hands.

To do this, you need to build using the following scheme:

We weld the upper and lower frame and assemble the body of the workbench. To do this, we assemble the frames by welding 4 legs to them. The height of the legs is not more than a meter. The main structure is ready.
We toughen the structure by welding stiffeners from the strip and corners.
We mount and install fixtures for shelves, drawers and their guides.
A crate is being assembled for a protective screen and hanging wrenches and another tool. To do this, at the corners of the tabletop, we weld the racks from the corner and overlap them on top with a horizontal corner along the entire length. For reliability, you can weld a stiffener from the strip. We sew the screen with a sheet of plywood or DSP. Then, we arrange individual places for the location of keys and other locksmith tools.
After completing the main assembly of the structure, it must be degreased and painted with any paint. The best choice, in this case, would be hammer paint. It is more resistant to mechanical damage.
From plywood sheet we make shelves and boxes. We assemble the boxes using small pieces of the corner and twisting them with plywood parts. We fasten the guides to the boxes, fix the handles. We impregnate with impregnation and paint over.
We fix the selected material on the countertop - it can be plywood, a DSP sheet or boards. Having previously treated with impregnation from decay, we fasten the countertop to the base with metal screws. The heads of self-tapping screws, made under the sweat, are deepened into the countertop, puttied and then painted over with paint.
On top of the tabletop we lay and fasten a sheet of metal cut to the dimensions of the table. We paint over it.
We install boxes, shelves, means of fastening the tool on the screen. We check the location of the workbench in terms of level and reliability of assembly.
Now it remains to install a bench vise, a grinding machine, put the garage belongings on the shelves and hang the tool.

All. We answered the question: how to make a workbench with your own hands.

In conclusion, it is necessary to recall some main points.

The design of the garage workbench must be stable and stand without warping and staggering. For better stability, it can be pulled to the wall on the anchor.

Organize workplace so that nothing gets in the way of your business.

All protruding parts must be turned and free of burrs.

Keep your work area clean and clear of spilled oil, chips, and other debris.

At right production work and normal maintenance, your workbench will support a load of at least 250 kg and will last for a very long time.