How to trim the ceiling plinth with a stusla template. How to cut off plastic plinth: how to cut off and how correctly, cutting methods cut off the ceiling plinth under 45 degrees

How to cut corners ceiling plinth. Photo 1.

The problem of cutting out the external and inner corners of the ceiling plinth faced, probably, everyone who at least once carried out repair work with their own hands. Plinth ceiling, it is also called a quilt, in repair it is used to hide the uneven border between the wall and the ceiling and give the interior completion. How to cut the corner of the ceiling plinth without stub? Talk about this and talk in our article.

How to cut the ceiling plinth in the corners without a stub? If you do not have a stus, it does not matter. Cut out external I. internal corner It is possible without a stub.

Today on the market, the cartel is available different sizes, forms and colors, with embossed patterns and without them. The material from which they are manufactured, also different. These are mainly: polyurethane, polystyrene foam, polystyrene and polyvinyl chloride. But lately The most popular B. repair work Wooded ceiling plinth. Its aesthetic appearance allows you to add the design of the room of elegance and rigor.

What kind of plinth is better?

Before properly cutting the corners on the ceiling plinth, it is necessary to choose to choose.

Tip: Ceiling plinth will look harmonious if its width is chosen correctly. The higher the walls, the wider there should be a plinth.

The most durable, moisture resistant and elastic are polyurethane cartlers And cut the angle in such a ceiling plinth is not very simple. However, all these positive qualities "overlaps" one weighty disadvantage - they cannot withstand sharp temperature drops, which does not allow them to apply in all rooms.

For example, in the kitchen, where there is a gas or electric stovePolyurethane cartlers will retain their original appearance of about a week. After that, with frequent cooking, when hot air will be closed to the ceiling, then descend, they will begin to deform, spoil the whole "picture."

Plinths made from other materials also have their drawbacks.

For example, polyvinyl chloride products have increased electrostaticity and if dents will appear during operation on their surface, it will be impossible to eliminate them. With the slightest mechanical exposure, ceiling plinths from polystyrene foam and polystyrene break.

If we talk about what the ceiling plinth for stretch or ordinary ceilings is better, then an accurate answer here, probably, will not be able to give. Since each of them has their own positive and negative qualities. Therefore, the choice will still have to do to you, pushing off from the financial resources that you have, and on what conditions the hall will be operated.

How to cut corners without stub?

At first glance it seems that cut the corner of the ceiling plinth notit is difficult - cut the edge of the plinths at an angle of 45 degrees and glued. However, it is completely wrong. Each angle of the room may differ in its parameters, for example, one 90 degrees, another 88 or 92.

This difference is the norm, especially in buildings whose age is more than 30 years. Therefore, if you simply cut the plinth at an angle of 45 degrees and glue it on the border between the ceiling and a wall, a clearance that should not be formed. How to docile the ceiling plinth so that there is no gaps? So, let's begin.

To begin with, you need to prepare the tool that the edges of the plinth will be cut. It can be saw on metal or a conventional sharp knife.

How to cut the inner corner of the ceiling plinth without stub? The answer lies but the surface.

Step 1. Take the plinth and attach it to the corner in the same way as you can glue. Pencil draw on the ceiling line along the plinth. Remove the cartel.

Step 2.. Attach the second plinth on the other side of the corner to the place of its adjoining with the first. Do the same procedure as first. As a result, you should get marking.

Step 3.. Take the plinth, lean it tightly to the place to which you can glue, and transfer the point of contact with two direct, drawn earlier on the ceiling. From this point, swipe to the opposite edge of the plinth. This line will be a slice of cut.

Step 4.. Do the same procedure with the second plinth.

Step 5.. Cut the edges of the plinths on the planted line.

Step 6.. Attach cut plinth to the corner. If the place of their junction does not have slots, you can start sticking a stick. If there are gaps or irregularities, adjust the cut corners with a knife.

How to cut the outer corner of the ceiling plinth? When creating an external angle, the upper part should perform above the lower, internal - the opposite is the opposite.

Whatever the ceiling of the ceiling, whether it is a ceiling in the bedroom or kitchen, do not rush, measure everything thoroughly. It will help you avoid damage.

The quality of the ceiling finishes greatly affects the appearance of the room. Therefore, try to do everything perfectly, or very close to it. Ceiling plinth serves as the final stroke. They give the finish finished and holistic appearance. Planks themselves smooth surfaces Mounted simply: on special glue white colorBut with the design of the corners there are problems. Without knowledge of how to make the corner of the ceiling plinth correctly, a lot of material is spoiled. About how and what to cut it in the corners and tell.

What makes and what is called

The very first plinths on the ceiling were made of plaster. They were cast in special forms, then mounted on the ceiling. Called such curly ornaments cartoons. Today it is necessary to see them: they are expensive, and externally do not differ from cheaper options. And the name is almost lost.

The most popular today ceiling plinths from polyurethane or polystyrene. They are inexpensive, look wonderful, easy to install, have a wide range of profiles and drawings. Width can be from 5 mm to 250 mm. They are used in almost any premises decorated in any style. Exception - here most often use wooden crafts - Style dictates its conditions.

There is still a similar finish of plastic. It is mainly installed in the bathrooms. But in wet rooms you can easily mount polyurethane planks - they are not afraid of dampness.

Cutting the ceiling plinth in corners from any material is needed according to one of the methods described below. The exception is only plastic plinth: it is possible to arrange such an angle using finished corners.

What and how to cut off

Work with plinths from miscellaneous material It implies use different tools For cutting. When working with the ceiling plinth of wood, it is more convenient to work with a saw saw. All other, including plastic, polyfoam and other polymers, are better cut by the metal web. It turns out a more even slice, less burr. Saws are usually used when working with stupid.

When working with plinths from foam, without special devices, they cut them with a good stationery knife. Its blade is quite subtle and even, the slice turns out smooth, not jammed. If you work with a polyurethane or polystyrene, do not press much: you can remember.

In general, to bring a little to the instrument and material, take some piece and practice it: cut, saw, cut. So when working will be less problems.

How to get the right angle

Most of all problems when working with ceiling plinths occur when the corners are designing. Since the surface of products is complex, it is easy to cut under the right angle: it is necessary to cut it back so that they docked and preferably - without large slots. In fact, there are several ways to make an angle of ceiling plinth ideal (or almost).

Using Stusla

If the corners and walls in the room are smooth, you can use a special joiner's tool - Stuslo. This is a chute in the form of an inverted letter "P", in which the lines for the propyl at an angle of 90 ° and 45 ° are outlined. The part is stacked inside, in which you need to do, the saw in the guides is inserted. The part is held in place, is cut under the desired angle.

In the case of plinths, not everything is so simple: they must simultaneously lie down to two surfaces, because they need to be pressed to one or another wall of the stouch. When working with the ceiling, they are pressed into your neighbor to you.

The sequence of actions when finishing an external angle you need to be made in an angle of 45 degrees. Stuslo put in front of you. Inline how the plinth will be located, determining which part it will be attached to the ceiling. In order not to get confused and cut off the ceiling plinth correctly, the plank, which will be located on the right, are placing on the right, the one that is left to the left.

That part that turns out to be on the ceiling, pressed to the bottom of the stus. The second side turns out to be closer to you and raised. It is restored on the wall of the device so that when it is cut, it is not risen. That is, the facial part of the plinth is turned away from you. The direction of the cuticle do, as shown in the photo below. After folding the two cut parts together, get a protruding - an outdoor or outer angle.

How to make an outer corner of the ceiling plinth using a chair

Pumping parts first apply in place "on dry", without applying glue. If the geometry of the angle was not so perfect, you can adjust a little with a knife. Small errors easier to smell with a special putty.

With the inner corner of the ceiling plinth, the situation is very similar. First, you try on which side will be on the ceiling, this part is pressed to the bottom of the stub, the second part is based on the wall close to you and you are being drove as painted in the photo below.

And again, at first try without applying glue, if necessary, adjust slightly. Then apply a thin strip of glue on both surfaces that will be glued to the wall or ceiling.

Your own option of how to use the stupid is shown in the video.

How to make the corner of the ceiling plinth without stub

Few in apartments or houses have corners of exactly at 90 °. Small deviations are easily adjusted after fitting. But not always. Then you have to post everything "on the spot" - under the ceiling.

We need a finely outlined pencil (solid - it is not so visible on the ceiling, but it leaves quite clear labels nearby), a small piece of plinth, a ruler and a good stationery knife, if you work with baguettes from polyurethane (polystyrene) or saw for working with other materials.

Plinths apply to the corner, spend a pencil along the outer edge. Apply to the other side of the corner, also celebrate. You turned on the ceiling of the cross, the center of which marks the place where the slats of the ceiling plinth must be converged (see photos). Having installed in the angle of the segment of the plinth, which will be glued and supervised by it to the wall in the wall, transfer the mark to it.

How to make angles on ceiling plinths without using special devices

Now take a ruler and connect the edge of the plinth with the applied mark. If you just put the plinth on the table and cut off the line, in the corner two parts will still not be collapsed: the inner part will interfere. It can be cut later, trying on the ceiling. The second way is to install a piece that you need to trim on the table, the part that will be on the ceiling. And cut off the line, but keeping the knife at an angle of about 45 °. It will be necessary to adjust anyway, but much less (and less chances for an error).

The same operation is repeated with the second bar. Put K. the desired wall, Break out the end in the adjacent wall, mark the place where the cross is drawn, spend the line and then cut off. Adjustment is carried out "on dry" without applying glue.

Exactly the same actions you repeat for the outer (speaker) angle. Now you know another way of how to make an angle of ceiling plinth, and without stewed or other special devices.

With decorative corners

There is another one, the easiest way. For polyurethane or polystyrene plinths use ready-made, factory decorative corners. They are installed in the angle, the planks are close to them. It is very simple to cut them if necessary: \u200b\u200ba few millimeters with a regular stationery knife.

How to dock in the corners

If the installation of the first corner is passed, we can assume that you have almost learned to do. "Almost", because you need to learn how to connect the corners and cut the strips along the length. When it is glued already some part and a small distance remained to the corner, as not to be mistaken with a length? The answer is simple: Leave the reserve.

At first, you can cut off a piece longer than 10-15 cm: it will be able to redo the opportunity several times if something fails immediately. Then make the angle described above in the way, try on dry, all customize that the result arranged. Only then can attach an already cropped bar in the angle and mark the place to which it can be shortened. You need to trim exactly at 90 °. It is not necessary to use a stouch. Just try to put a knife (hacksaw) perpendicular to the surface.

In the interior use many types of platbands. They differ in the material from which are made, their shape, color and quality. Usually, either wooden or plastic platbands are used for framing doors or windows.

By their form, platbands can be divided:

• Flat - have a simple, uncomplicated look, and they are most often used.

• Rounded - the frontal part of the framing has a rounded view.

• Figured - can combine various forms in themselves. They look very unusual and quite attractive.

The material from which the planks make may be the most diverse:

• The tree is the most common material, as it is eco-friendly and not expensive.
• Plastic - make any color and shape. The most durable material and quite simple in the installation.
• Metal - allows you to experiment with the most unusual patterns, create various forms.

Also the framing is classified by the type of thread.

• The slit - pattern is done through the entire area of \u200b\u200bthe plank.
• Patch - the finished pattern is naked or stick to the finished background.

According to the method of mounting the platband, there are only two types.

• Overhead - mounted on the doorway.
• Telescopic - they have nozzles that are inserted into the holes of the door frame when installed.

How to cut off a platband with stusla

Tools will be needed for work:

• Stuslo;
• Hacksaw;
• Crafting table.

Stuslo - a tool, thanks to which you can cut a product at any angle. It looks like a tray that is made of wood or metal alloy, but most often it is made of plastic. In the construction market you can find a simplified version, it will be needed for cutting at an angle of 45 degrees, but there are more complex structuresThey are designed for cutting at an angle of 90 degrees.

In such a work, it is also important to use what a cutting tool. Depending on which material, the framed is made, you need to choose a specific tool so as not to damage the product. For example, for cutting metal plank It is suitable for the metal with metal, it will also fit for a plastic framing. And for the wooden product you need to use the tree with a tree. Will it be used when cutting right toolDepends the accuracy of the saw and the quality of the work done.

Workbench will facilitate the work in terms of the fact that all required tools will be at hand.

So that the bar is cut off correctly, you need to accurately perform step-by-step instructions.

Step 1. Frame must be leaning to the doorway and mark the required length, then cut off the excess part.

Step 2. The bar is installed in the stouch in this position in which it will be attached to doorway. It must be pressed to the long side of the tool.

Step 3. At an angle of 45 degrees, cut off the bar.

Step 4. By the same principle, we set to the long side of the tool to the second response bar and its mode.

For the accuracy of the work done, before the fastening, we connect the two parts of the platbands, and if there are no cracks between them - you can begin to be installed.

For a complete presentation of this work, you can watch a video.

How to cut off the platbands yourself without the help of stusla

If there is no possibility to use the stupid, you can make it yourself or do without it.

To properly cut the framing without the use of a special tool, you can use the usual markup on the wall and at the same time get not a bad result.

To work, you will need:

• Pencil;
• Roulette;
• Line;
• Hacksaw.

To perform work, you need to follow step by step instructions.

Step 1. Select the bar to the wall, where it will be attached, and watched a small line along it.

Step 2. Now it is also necessary to read the line, putting the second platband, where the angle should be.

Step 3. When everything is battered, you should get a markup on the wall that looks like two crossed lines. The point where these lines intersect must be transferred alternately into two strips.

Step 4. The marker transferred to the framing and will be a slice line, for this from the mark and to another end should be burned and cut off.

Step 5. We apply two parts of the plank to the wall to adjust the angle, if it happened not to dock.

To cut the angle, applying a homemade stub, it is quite possible to draw on cardboard, blackboard or on the usual sheet of paper. To do this, we need to turn the corners under the desired degree. Enjoy homemade tool Just as purchased, namely I put the platband parallel to the line with the desired degree and cut it off.

The main advantage of such a drawn tool is that it is possible to draw an angle absolutely at any angle.

How to attach the platbands

When the corners of the platbands are cut, you can mount them to the wall. It is recommended to do this with decorative nails with small hats, not glue, as glue is not durable. And if the framing must be replaced or removed for painting, with nails to make it much easier, and if the plank was attached to glue, then when removing it can be easily damaged.

There are only four ways to attach such framing:

1. Finish nails
2. Liquid nails.
3. Samores.
4. Use of platbands on latches.

Installation using finishing nails The most common method. It is recommended to use nails 4 centimeters in length and not more than 1.5 millimeters with a diameter. Holes are drilled at a distance of 5 - 7 centimeters, after which nails are clogged, but not to the end. Now you should remove nails hats using booths and mask the wax pencil of the same color as the plank itself.

If the surface of the wall to which the framing will be completely even, and the planks are made of mDF material That is suitable for fastening on liquid nails. To do this, you need to apply such nails on the wrong side of the plank and attach it to the wall, keeping in this state for some time. After that, the fraction of scotch should be fixed. This method is quite simple and its main advantage is that the front part will not be exposed to mechanical effects. But when it is removed, it will be necessary to make a lot of effort.

Tip! At first pin the wall and tick it outside. After the platband, you can remove, and on the contour glue the greater tape - it will easily cut off, without leaving traces, even from the most capricious surfaces, but if there are liquid nails somewhere, you do not have to rub the glue from the wall. It will be enough to just rejuvenate the tape.

To attach a pen with self-draws, it needs to be done not very deep, but quite wide holes. It will be needed so that the hats of the screws are not higher than the framing itself. To reorganize the screws, you can purchase special caps on them of the same color as the plank itself. It is recommended to use screws 2 centimeters long and no more.

The door framing on the latches externally resembles the letter "g". It is fixed extremely simple, which is a plus. Its "key" moves into the hole and snaps. The minus of this method of fastening is that it is not so easy to remove it and when re-attaching the platband can be stupid, and it will not look beautiful.

All of the four proposed embodiments of the framing are not difficult, you only need to choose the one that is suitable for the interior of the room.

This tool is a profile in the form of an inverted letter P. On the sides in it are slots for peeling at an angle of 45, 60 and 90 degrees. More complex angular patterns or stubs have devices to exhibit different angles of dummy.

For an inexperienced master the best option It will be the purchase of a ready-made stouch in a construction store. At home, it can be made of three praised boards or plywood.

The tool can be collected by bonding between themselves in advance of the prepared parts. Ku corner template It is necessary to be copper with a joinery of joinery or screws. The side walls of the stub must be strictly parallel to one another. Horizontal bar Must create a strict perpendicular with side.

Step 3: We plan slits at different angles to cut the laminate, platbands, etc.

The application of the slot will influence the accuracy of the work performed in the future. Therefore, it is necessary to approach this process with special painstability. Propyls are desirable to produce with the help of the same hacksaw, which will be performed.

Step 4: Preparation of the material that must be sprinkled at an angle of 45 degrees

It is necessary to secure the finished corner pattern on the desktop using clamp. Next to the workpiece should be marked with a future cut. Next, it is necessary to combine the workpiece with the slot of 45 degrees inside the stouch and tightly press.

The hacksaw must be inserted into the appropriate grooves of the angular template and cut the blank. The grooves will limit the saw movements and propyl will be carried out in the right direction.

Subtleties of working with stupid and various materials

When sawing such elements as the plinth is not always worth it to do, 90 degrees. After all, the walls in the room can be uneven. Before pressing the plinth, it is necessary to correct the corner of the cut.

Thus, the article described and characterized the process of cylinding wooden materials Using stusl.

Plinth is an integral element required for the design of the room and giving it a complete and neat look. It can be made of different materialsBut the plinth plastic is now specially popular. It is easy to install, but even in this process there are some subtleties about which it is important to know. How to cut plastic plinth That's right, so that it is possible to take it gently docile in the corners?

Previously, the plinth was made mainly from the tree and were considered to be wooden products. But now in construction stores you can find such elements of the decor that are created from metal, and from plastic and other materials.

Wooden plinth is a classic. It is a natural product, as it is made of a solid wood massif. This species is characterized by high strength and durability - plinths installed in the times of the USSR, so far faithfully serve in some apartments and homes. Now they are made mainly of pine wood, but there are products from walnut, oak, ash and other breeds. However, due to this, the cost of products is growing - such plinths are not for everyone on the pocket.

Because of this, brackets veneered at the market appeared on the market - they are an order of magnitude lower. However, they are practically no different from products made from expensive wood. The fact is that the upper part of them, which plays a decorative role, is made from a thin layer of expensive wood. Without certain knowledge and experience, veneered plinth from ordinary wooden to distinguish almost impossible.

On a note! For cutting plinths - wooden and veneered - used normal knob on wood.

The plinth plastic is now especially popular, that is, made of PVC. He partially displaced ordinary wooden products from the market, as it has a number of benefits:

• it looks beautiful and neat - able to imitate products from a natural tree;
• easy to install, flexible and very easily cut;
• it can serve as a cable channel for laying wires;
• it is not afraid of water exposure, and also does not rot, the mold does not start;
• it is inexpensive compared to wooden or veneered products.

Plinth plastic is made of polyvinyl chloride, which is passed through special forms under high pressure. After soaring the mass, a neat plastic product is obtained.

On a note! Some manufacturers draw up edges of plastic tire plinths. This measure helps the product not slide along the walls and floor during installation and tightly lay down to the surfaces.

Plastic plinths are several species - for example used for carpet (have a special form in the form of the letter G, fix the material) or for Linoleuma. There are universal products that can be installed in any form. outdoor coating. They may be classified and depending on rigidity.

Table. Types of plastic plinths depending on rigidity.

View	Description
	Out of shape resemble ordinary wooden plinths, can be installed both by the floor, and under the ceiling. The product is based on ordinary polyvinyl chloride, due to which the plinth has all the qualities inherent in this substance - durability, rigidity, all sorts of colors and moderate flexibility. However, with a strong pressure, the product can be easily breaking easily.
	This type of plinths in appearance resembles a flexible tape, which is stacked along the wall without having to pruning, which makes the installation is much easier than in the case of rigid plinths. They are also made of PVC, but in view of the modest external data do not have such popularity as ordinary hard. The main advantage is the possibility of using indoors with uneven walls, but products are glued on a special polyurethane-based adhesive or putty.

How to trim the corners of the plinth

Since during repairs, it is more common that rigid plastic plinths are used, then it is about them that will be discussed. Their installation is inevitably associated with the need to cutting and forming beautiful junctions in the corners. From how the plinth will be docked, as a whole and will depend on the quality of all the work and the appearance of the room where the repair is made.

Methods of cutting plastic plinths

Cutting the plinth - seemingly simple, but responsible occupation. If the angles are incorrectly cut, they will not correctly stick and all work will go to the pump, as the product will no longer have beautiful view - The gaps will remain between two plots of plinth and decorative inserts (corners, docking elements, etc.).

Most often for cutting the plinth applies usual hoven for metalwhich has small teeth. However, for thin plinths it will not work, as the product simply breaks under the influence of this tool.

Sometimes plinth cut and scissors for metal. But the method also has its drawbacks, because the product can be sought under the pressure of the blades. Less frequently, but still used Bulgarian. However, the cut line after it can be non-accurant, since the tool often "tears" soft plastic. Especially often this method is unsuccessful in newcomers in the repair world, which still do not know how to control the work completely. So the grinder can be attributed to fairly specific ways.

On a note! To cut a thin baseboard, you can use a sharp knife or stationery knife. But such work requires some skill, therefore it is recommended to first take off on the trimming of the old plastic plinth.

The most important thing in the procedure of cutting the plinth is observing the necessary geometry. The procedure is never performed "on the eye", the accuracy of measurements and accuracy are important here. Therefore, there are other methods of plinth cutting.

Cutting on stencil

The method is recommended for cutting products intended for installation in non-standard rooms in the form of rooms with angles that differ from the standard mark of 90 degrees. Stencils of the desired angle can be made of paper or fine cardboard. First out rough material Cut stripes that have exactly the same width as the plinth. Next they are applied into the angle and fixed, after which they are cut on the form of an angle. Then, on the obtained stencils, the plinth itself is cut under the necessary angle.

Cutting outdoor baseboard with stusla

For proper trimming Plinth was invented a special device that got a name stuslo. It is a small bar with a recess for the plinth and with gaps located at different angles - for cutting tool.

With the help of a stub, you can get neat and smooth sections. The plinth is fixed inside the product, then the angle and direction of the cut is selected in a particular case.

On a note! If necessary to form beautiful corner Using the stouch, one segment of the plinth is cut at one angle, and the second is in the mirror image.

During working with a stupid, it is important to ensure that the edges of the plinth be played by the edges of the selected slot on a short distance. If the trim tool has a greater width than the plinth itself, it is recommended that it is recommended that it is recommended to secure the product inside the stus. Otherwise, the plinth can move inside, the cutting angle will constantly change, because of which it (cut) is incorrect and wrong.

Important! During the cutting pressure on the plinth should be moderate. Otherwise, he may break.

Using a ruler and pencil in the absence of stub

If there is no stouch at hand, but I don't want to do stencils, you can try to apply the necessary markup on the plinth with a pencil. In the case of the formation of an inner angle, the line width is measured, then the resulting value is deposited on the end part of the plinth, and from its angle to this marked point, a pencil line is performed, according to which the cut will be made. The second plinth, which will be together with the first to form an angle, is simply clipped by the first one applied to it.

Important! If the installation of plinths is performed in a room having a complex geometry, then all the angles will have to be thoroughly washed to prevent an error.

Experienced masters recommend starting the installation of the plinth from the inner corner. At the place of the joint of two walls, which form an inner corner, the slice on the plinth will be equal to 45 degrees (in the room with the right and accurate geometry). Cutting is recommended to be performed using a stouch - only this can be achieved perfectly smooth cut.

Tip! If you need, you can easily fit the plinth to each other with a grinder or a rashpil, slightly "removing" their edges.

In general, in any case, the cropped edges of plastic plinths should be stamped - so it will be possible to get rid of sharp edges, and it will work easier. And the cutting of plinths with cable channels is made only after the product disassembly - decorative Planca, designed to conceal the wires and places of attaching the plinth, is cut separately.

It is recommended immediately before installing the plinth cut on the required length of the segment and arrange the angles in order not to be distracted by this procedure during the plinth assembly. Do not neglect and use additional elements - Plugs, corners and other plinth products. With their help manage to give finished work Finished and harmonious appearance.

Tip! If the angles where the plinth is stacked, uneven, then it is possible to cut even decorative plugs and other elements if necessary.

How to cut outdoor plastic plinth

If the angle in the room where the walls of the walls and the floor of the plinth are planned, is equal to 90 degrees, which happens extremely rarely, then plinth sections should have an angle each in 45 degrees. This is the easiest to make such a cut, especially with the use of stusl. It is enough to insert the plinth in the stub, then select the groove of 45 degrees and make a cut.

However, such angles of 90 degrees in the premises are extremely rare, usually they differ in several values \u200b\u200bin one direction or another. And in some rooms and at all angles may be more. Then cutting is performed differently: markup is drawn on the floor with a pencil, where, from the same side of the corner, the location of the plinth is drawn - it will turn out to be a small rhombus. Diagonal of this rhombus and will be the very line of cutting products. Next, the plinth is applied to the markup, which makes the markup in accordance with the diagonal of the rhombus. If it is directly spent from this mark to the corner of the plinth, then the very line Line Cut.

The external corners of the plinths are formed a little differently, or rather, in the room with an ideal geometry, it is also possible to cut the products at an angle of 45 degrees (but in another direction) and after docking to close the edges of the plug. Non-standard angles are cut into this: one of the plinths is applied to one of the walls, its borders of the pencil are noted. The same procedure is made with another product - again on the floor there is a rhombus, the diagonal of which will become a guide for cutting products.

Instructions for trimming the plinth

Consider how the trimming of the plinth takes place with the help of stouch and hacksaws.

Step 1. After all size shot The plinth is placed in the inner part of the stub and pressed to one of its walls.

Step 2. With the help of the hacksaw, the plinth trimming is performed. Cutting (sawing) The tool is inserted into the selected groove - it can be cut.

However, sometimes plastic plinths enough to trim at right angles - now it appeared on sale a large number of Different additional products for them. For example, there are such corners that will allow to hide smooth cuts and it is beautiful to arrange everything. Your attention is an instruction on the installation of plastic plinth.

How to mount the plinth? The answer is here!

In general, all existing methods Plinth attachments can be divided into two categories - installation by mounting to the floor and mounting to the walls. You will have to choose depending on the type of plinth and the design features of the residential premises. Read more in detail.

Step 1. All measurements are removed - the required length is determined for the plinth segments. These values \u200b\u200bare deposited on two products from which the angles will be formed.

Step 2. The plinth is trimmed with a stouch and any cutting tool and applied to the walls - it is necessary to make sure that products are cut correctly and have the necessary length.

Step 3. If everything is done correctly, then the plinth is screwed to the wall using self-tapping and dowels. But before this, plugs or corners are put on their ends.

Step 4. At the outer corners of the plinth are connected with each other with special plastic devices.

Step 5. The plinth is installed on the place appointed to it and is screwed to the wall by self-draws.

Step 7. The cable channel with laid wires is closed with a decorative plug.

Step 8. Exterior angles Closed with special corner plugs that are simply put on the edges of the plinths forming the angle.

Video - how to cut the plinth

Video - secrets of plastic plinth installation