Broken stapler stationery. The furniture stapler does not score a bracket. Types of furniture staplers

The furniture stapler successfully replaced in many areas of the usual hammer and nails. Its use allows you to connect the same or different materials on the hardness of materials between themselves, for example, wood, phaneur, plastic, plastic film, fabric. With regular use, the instrument can start working badly or breaking at all, but many breakdowns are easy to eliminate own hands. To do this, it is necessary to familiarize yourself with the design of a bobbin pistol, which is frequent of its faults with the methods of eliminating, and stocking of plumbing tools. Only in fairly rare cases, the repair will require the involvement of the service center specialists.

Energy type bobbin pistols, with which the fasteners are clogged into the surface of the material, are divided into such types:

mechanical;
pneumatic;
electric.

In everybody, mechanical and electrical models of tags are mainly exploited. Pneumatic tools refer to a professional category.

Mechanical models

Any furniture stapler has in its design. store under fastenerswithin which there is a clip with guides. Consumables are inserted into it when performing working operations.

Shops of some models have a transparent insert. It is convenient during operation, because it allows you to control the remaining quantity of fasteners.

Schedule device mechanical view Described in detail in the photos below.

Shock-returned mechanism (Single) is a plate. Its size corresponds geometric parameters used consumables. Bohek is attached to the striker - its form is determined by the taker design. In this case, the drummer is in contact with the spring, the compression of which is adjustable using the screw. Harking impacts is provided by a polyurethane shock absorber, which is located inside the housing.

Manual brackets can be equipped with springs of two varieties:

twisted (shown in the photo above), installed on inexpensive models;
plate (spring type, photograph below), more powerful and expensive compared to the first.

Mechanical bobbin gun manager lever (handle). It will have a shock-return mechanism. During transportation or when stored from a random trigger, protects the safety bracket.

Electric and pneumatic models

The device of an electric taper connected to a 220 V network is presented in the photo below.

The numbers are indicated by the following design elements:

trigger launcher;
fuse;
handle to hold the instrument;
power cord;
enable / shutdown button;
mechanism for regulating the force of the shot;
shop pusher;
store clamp.

Inside the tool housing are also located:

electric motor that segges the spring;
electromotor management fee;
impact mechanism.

No power cord has no power cord. Power power tools gets from batteries.

Separate elements of the design of pneumatic bobbin pistols are shown in the photos below.

Inside the pneumatic tool is located cylinder with piston, as well as an air distribution node. Compressed air for functioning construction stapler Enters the hose capable of withstanding a large pressure, from the compressor installation or a cylinder. Therefore, if there are problems of working at a pneumatic taker, you first need to check the self-maintenance of the compressor with the aircase.

Common faults of the construction stapler and their causes

The construction stapler of any kind can start working badly. At the same time, common malfunctions for the considered species of bobbin pistols are the same. Only the reasons why breakdown occurred, can be very different - this is due to constructive differences different species tags. Consider what to do in each case.

The tool does not work - the brackets do not fly out

So, if an electrical or mechanical bobbin gun does not shoot brackets or nails, then the reasons may be the following:

the spring was broken;
problems with the drummer.

Mechanical devices can also wear a wax lever with a spring.

W. power tools There are more possible reasons of which, because of what fasteners are not fired:

the tool is not included in the network 220 V;
cord with defect (violated its integrity);
the electric motor burned down;
electric motor management fee fees.

Electric Stapler NOVUS J-165-EAD

Pneumatic tool Does not shoot consumers in such cases:

the compressor broke or not connected to the power grid;
breaks the hose;
completed compressed air in the cylinder;
problems with cylinder, piston or air distribution system.

Fasteners stuck

Expendable material in all models is stuck for general reasons:

when it does not match the sizes for the operated taker;
polluted fasteners or store from the inside;
applied consuming with defects, for example, bent.

Staples are not completely clogged or, on the contrary, too deep

Any bobbin gun does not score brackets, nails or pins completely, if the depth regulator is configured incorrectly.. In such cases, it is enough to adjust it. Manual I. electrical devices The problem is also often associated with the wear of the spring, and in pneumatic - with a clamping mechanism or insufficient working pressure.

If fasteners are driven too deep, then the reason may be pressed spring or high pressure compressed air.

Important! The compressed air pressure when using the pneumatic tool can be raised no more than the value indicated in the instruction manual.

During a shot, 2 brackets crashes

When the stapler during a shot knocks two brackets, the simplest reason Problems is the use of dirty consumable material or non-dimensional brackets. At pneumatic bags, the problem may be associated with disruption of compressed air. In electrical and mechanical models, the problem is often caused by the wear of the booze or the deformation of the drummer (or its guides).

It also happens that the equipment of the gilt brackets. This also occurs due to their low quality, or the inconsistency of the consumption of strength to the material of the connected elements.

Algorithm Disassembling stapler and troubleshooting problems

To independently fix the broken stapler for mechanical type furniture, you will need such tools:

screwdrivers;
vice;
filty or small metal file;
a hammer;
pliers.

In some cases, it may also be necessary hand saw Metal or Bulgarian, when repairing the power tools - a multimeter and a soldering iron with a pack for soldering.

To check freedom of flow of consumables inside the store, it is enough just to open it or pull out the pusher.

Spring replacement or repair of a worn shock mechanism Perform in such a sequence:

get the remaining consumor from the store;
twisted the screw that regulates the strength of the blow;

take out the spring;

disassemble the body of the tool, for this remove the washers and pull the pins;

get the shock mechanism;

if the fault is associated with a spring, then replace it;
when the drummer is worn (there is a production in a brisk or in the place of contact with the rocker of the starting lever), it is clamped in visks and give parts using a file or the original shape;

collected in reverse sequence tool, lubricating the shock mechanism.

At the impact mechanism may also be broken focus for the spring (photo below), and because of this, the bracket works poorly. In this case, to eliminate the malfunction, you will need spear upusing welding.

Repair activities do not occupy a lot of time and often do not require financial costs, but the service life of the bobbin pistol is prolonged.

How to disassemble and repair a pneumatic bobbin pistol, shown in the video below.

Disassembly and prophylactic maintenance electrical model Schedule is shown in the roller below.

To maximize the service life, it is necessary to store a building stapler under the following conditions:

the magnitude of the relative humidifier of air not exceeding 70%;
temperature should be higher than +5 degrees Celsius;
the air of the storage location should not contain vapors of alkalis or acids, as well as dust-abrasive inclusions.

In order to repair the stapler, in many cases you only need to correctly adjust the depth of the shots, setting it under certain materialand also use quality, suitable fasteners. When the stacking does not work at all, it will be necessary to perform more serious repairs, often accompanied by a replacement for broken or worn nodes. By performing repair operations, it is necessary to remember the personal safety: consumables to remove, put the device for the fuse and de-energize the electrical and pneumatic models.

The first staplers appeared in France in the XVIII century, they were specifically invented for the King of Louis XV. But at that time, this device was unique - every bracket was done manually for him, it was a stamp sign. Make a stapler affordable for most people managed only at the beginning of the 20th century in the States.

Types of staplers

In stores specializing in the sale stationery, You can find various devices for fastening securities. There are so-called pocket options. This category includes any stationery stapler, which can be safely placed in the palm of your hand. The case of such devices is usually made of plastic. They can simultaneously flash a small number of sheets. Their main advantage is low price. But it is worth remembering that they are not suitable for intensive work. With active use, they will soon have to look for a replacement.

The offices most often buy desktop staplers. They undesirable to fasten paper on weight. Devices are designed to work on a solid, smooth surface. At the bottom of them, as a rule, a special anti-slip coating that does not allow them to move on the table even with the load.

Stapler stationery is very different even in its appearance. It is equipped with a special lever for which it is necessary to put pressure on the paper sheets. The most powerful models are able to fasten up to 260 sheets at the same time. Often they are equipped with special devices designed to remove the cut brackets. Some devices have a special fixing plank. It is designed to adjust the depth of the bond.

Types of stitching

Do not everyone know that the stationery staplers differ depending on how they fasten sheets. Most office employees are familiar with ordinary options closed type Stitching. Such a stationery stapler bends the edges of the bracket inside. This is considered the most reliable way of fastening paper. He is the most common.

There is also open type. In this case, the brackets bend outward. This method is preferable to use in cases where only the temporary firmware of sheets is needed. Bonded in this way of paper is easily disconnected, while traces are practically not visible.

Sometimes in offices use a special stationery stapler with straight brackets. It is necessary in those situations when it is necessary to attach paper (some announcement or document) to a special board with a soft surface. It can be made, for example, from traffic jam.

Important nuances

When purchasing a device for connecting papers, it is important to consider how active you will use it. If you plan to often exploit it, then pay attention to metal options. They are considered more reliable and will serve longer. In other cases, conventional plastic devices are suitable. The principle of operation they have absolutely the same.

It is also important to consider that staplers differ in power. This indicator depends on how much the sheets of sheets can be made at a time. By the way, it is also important to choose the right brackets for stationery stapler. It is advisable to know not only their size, but also the manufacturer. At the same time it is necessary to take into account that thick brackets are needed for more powerful devices. Otherwise they will bend and break while trying to flash papers with them.

In addition, you need to know that there are devices that work only when the table or other smooth surface. If such a stapler is trying to bore paper on weight, then the brackets will fall out or deformed.

Additional options

It seems to many that the stationery stapler is a fairly simple device that can no longer be improved. But manufacturers make it use more convenient. So, when buying, pay attention to the fact that the plastic footboard or rubberized inserts are below. They will protect your table from scratches.

Another important and convenient addition is the presence of built-in desteptor. This is a special device with which you can quickly break the brackets. It will come in handy in those situations when you need to disconnect the previously bonded sheets. Squeeze the brackets with scissors, and even more nails, it is inconvenient, and it looks untouched.

Principle of operation

If you are seriously approaching the instrument selection to fasten the papers, then you will be interested in the stationery stapler. In a special metallic chute staples are inserted. They are moving forward using a spring or a special plate.

It is worth noting that the second option is considered to be more practical. This is due to the fact that the springs have a property with time to stretch, they can slip with hooks that are fixed. The plate is capable of providing more smooth operation of the moving tongue. It contributes to the fact that the rope from the bracket is always fixed at the edge. The pushing tongue can be made of metal or plastic. In the first case, it will be more reliable.

Download stapler

In the internal mechanism are inserted by brackets that, with a sharp press on the device, fasten and fasten sheets. When the clip ends, it simply needs to be replaced with a new one.

If you have a full-loaded stapler model, then you need to insert 1 new plate compressed brackets. But there are other options - they are adding ½ part of the clove. With ordinary pocket and office options easy to understand. To change the plate from the bracket, you do not need to look for what the scheme of the stapler of the stationery looks like. It is enough just to raise the top cover and insert the clip into the chute.

There are special models with front load. They have a button on the housing by clicking on which you release the spring of the mechanism. The chute goes forward.

A little more difficult to deal with professional devices. In some of them you can download even 7 types of brackets. At the same time, users have the ability to adjust the depthing depth.

Repair of devices

If you had an ordinary pocket or a small bench-top stapler, then when it breaks it, it is best to buy a new one. But there are such problems that everyone can fix themselves.

First of all, it is necessary to remove the housing and remove the clip from the gutter. So you can see that at the exit of it stuck the brackets that interfere with its normal functioning. This, as a rule, is the main cause of breakage.

To work the stapler normally, it is necessary to extract all stuck brackets. This can be done with a tweezers or thin screwdriver. The main thing at the same time is not to damage the chute itself, the spring and the pusher. After that, you can remember how to assemble the stapler stationery. It is necessary to insert a spring into place if you shot it, install the housing and press the top to the bottom so that they are fixed.

These comfortable and ergonomic adaptations have gained quite well-deserved appreciation and professional furniture-workers, and homemade craftsmen. There are even such patterns of staplers that can work with small carnations. The use of a hammer with almost inevitable injuries gradually goes into the past. In addition, the speed of work is significantly increasing. However, this design sometimes comes in disrepair. Throw out an old stapler, just say, I do not want. Let's talk about how to repair a furniture stapler with your own hands.

Classification

Distinguish such varieties furniture staplers.

Manual

Skobooking hammers

These devices clog the brackets with strong blows. Compared to manual counterparts, the speed of such a model is significantly higher. This tool is convenient to perform such works:

Fastening the insulation material.
Installation of rubberoid.

Important! In a word, a bobbin hammer is indispensable where, first of all, quickly requires, and not a filigree-accurate performance.

Construction cable staplers

This tool is used for mounting cables with a voltage load in 50 V. The maximum cable diameter is 7.5 mm. These staplers are used when performing such works:

Cable fixation.
Locking the electrical network.
Installation of communication lines.

Classic model

Such a tool equipped with manual drive has become a real classic. After being pressed the trigger, the bracket is clogged into the material. A special category is hybrid models, with which you can perform several types of operations described.

Important! You can also classify all modifications for professional and domestic ones. Professional models are distinguished by:
Convenience.
Large service life.
Lack of plastic parts.

The minus they have only one: relatively high price.

Operating principle

Depending on the type of drive, the tools are divided into electrical and pneumatic.

Electric

These devices are widely used in everyday life. With an electrical projectler, it is enjoyable, just to connect the device to the power grid. However, the electrical appliance, in comparison with the manual analogue, is much more expensive. It is advantageous to buy professional craftsmen who are constantly engaged in the repair of furniture items. Naturally, for one-time repair, buy such a model is unprofitable. Manual models are suitable for domestic use.

Pneumatic

In everyday life, these models do not apply because they will need to use them. compressor installation. You can purchase your own compact compressor, but how soon this purchase will pay off - the question. Therefore, to buy a pneumatic device beneficial to companies for the production and professional repair of furniture items.

Sometimes it happens that the stapler refuses to work. Namely, the brackets are not flying out of the charger. Before repaid, disassemble the device in such a sequence:

Remove the screw knob.
Remove the spring.
Remove the protective cover.
Remove the pins and locking washers.

To successfully repair the furniture stapler, you will need:

A hammer.
Vice.
Screwdriver with flat sting.
Pliers.
File.

Drummer

Carefully inspect the drummer and appreciate its condition. The most common cause of incorrect operation of the device is the wear of the stubborn area on the drummer housing. With the help of a stubborn area, a joint operation of the shock mechanism and a trigger lever occurs.

Important! The drummer is the executive part. On the drummer presses the spring. You can adjust the spring force using a special screw.

Carbine

Charging Carabiner is located at a right angle to the impact device. In the drummer there are staples to which the spring affects. Staples unchanged closed to the plate attached to the body.

Trigger system

The composition of the trigger includes such components:

Spring.
Welcome lever.
Rocker.

How to use furniture stapler? To scoring the bracket, click on the lever. The rocker raises the drummer. After the bracket goes into the mechanism of the Boyhead, the spring is squeezed. The drummer with power is hitting the bracket, and that enters the base.

The rocker and drummer work synchronously. Otherwise, there is a "idle shot." It is necessary to adjust the stapler for furniture. The trigger worked, but the drummer did not capture the bracket. With strong wear of the thrust site of the drummer, it is precisely that.

To repair, time will need not very much:

Hold the drummer in vice.
Sharpen the protrusion with a file, giving it the original shape. This will significantly extend the stapler resource.

Important! It is only necessary to perform this simple manipulation after the device starts to work "dry". The driver of the drummer becomes all shorter and needs to be applied.

More recently, the most different upholstery works were carried out by nails and a hammer. Most of all it concerns furniture production. If turn over soft sofa or a chair, then on the back surface there are no hats of nails, special ties or brackets are thrown into the eyes.

These newest devices Conveted a construction market. There are even staplers that can perform work using small nails. The hammer with nails went to the past. No fingers, you do not need small nails. As a result, high performance. However, this design sometimes fails, but it is a pity to part with such a device. The question appears, how to fix the construction stapler, can it be done on your own?

It is much more convenient to work as a tool than clogged with a hammer. The speed of work increases several times.

Before starting the repair of a stapler, you need to get acquainted with its design, varieties and basic work criteria.

Main varieties of models

The manual stapler does not require careful care. You only need to periodically lubricate it.

Hand staplers. This group includes mechanical staplersEquipped with manual drive. They are divided into several types, the task that needs to be executed as a basis.
Bobbing hammer. This building stapler has a strong blow scores a bracket. The speed of such a model is much higher than the manual analogs, however, the accuracy of scabing leaves much to be desired. Such bobbin hammers in most cases are used for:

fastening insulation;
styling rubberoid.

In other words, the stapler is used where the speed of work goes to first place, and not its accuracy.

Cable building stapler. This tool is specifically designed for mounting cables withsting the load in 50 V. The diameter of the cable for operation should be no more than 7.5 mm. When choosing such a stapler, the wire diameter is taken into account, with which they will have to work. Most often, cable devices are used with a large amount of work when required:

fix the cable;
pave the electrical network;
mount the communication lines.

Ordinary models. This tool has already become classic among such devices. It has a manual drive, which is pressed against the surface, and after pressing the trigger lever, the bracket is clogged into the material.

Electric stagnants are considered one of the most powerful, because have reinforced springs.

Combined models. This construction stapler simultaneously combines operations that perform different kinds Staplers equipped with manual drive.

In addition to the models presented above, there are also other varieties of this tool. They are divided into:

professional;
household.

Professional models are characterized by their positive characteristics:

big resource;
ergonomics;
no plastic parts.

TO negative side You can attribute the high cost of the stapler.

Electrostelers. This type, gained widespread for household needs. With an electric stapler, it is very easy to work, just connect the electricity. However, the cost of such a stapler is much more manual analog. To just repair the furniture not economically buy such a model. For this work, the manual stapler is suitable. But if the conversation is about constant repair of furniture, it is better to use the electrical option.

Pneumatic models. Basically, such tools use professionals in their work. For household needs, such a building stapler is not applicable. Scoring a bracket comes from a pneumatic impact. Such air way It is used in the production of the air compressor.

In the event of a special need, you can install your own compressor, but it is better to purchase a compact model, the dimensions of which correspond to the size of a small suitcase. It will take only electrical network.

The price of such devices is incredibly high. In connection with this device, professionals are used that repair furniture. Such a pneumosteler is also found in private manufacturers.

Back to the category

Materials necessary for the work of the stapler

The pneumatic stapler works with compressor with compressed air.

Usually when the term "type of brackets" use the term, mean its thickness. It has different sizes and width brackets. In European countries, most often use brackets:

thickness - 0.75 mm;
width - 11.4 mm.

Mostly produced a lot of varieties of brackets with the most different dimensions. The choice of consumables depends entirely on the task. For example, long brackets are most suitable for creating high loads. For fastening not very durable material, for example, polyethylene filmIt is better to use brackets of large thickness. When the cable is fixed, the choice of the bracket depends on its diameter.

If you work as a branded stapler, it is necessary to purchase branded branded brackets. They are largely different from their usual fellow. They have many positive qualities, no corrosion.

These brackets are made of stainless material, have a galvanized surface. Besides:

perfectly sharpened;
they comply with all drawing data;
the stapel is distinguished by absolute accuracy;
have a warranty period.

The presence of a guarantee speaks of originality and quality of such material.

Back to the category

To use such a device is always nice. I installed the store brackets, pressed the stapler, pressed on the lever, and all the material is securely fixed. But there are cases when the brackets are not flying out due to the charger. There is only a trace from the drummer. Conclusion one - it is necessary to repair it. To do this, disassemble the stapler in a specific sequence:

remove adjusting screw;
remove the spring;
remove the protective casing.
remove pins;
remove lock washers.

For execution repair work Read:

pliers;
screwdriver;
a hammer;
vice;
file.

After this work, you can consider the drummer. The main breakdown of the tool is the production of the dripping platform of the drummer body. With it, it provides a joint work of the trigger and shock mechanism.

The drummer is the main executive part of the stapler. A powerful spring presses on it, the force of which can be adjusted by a special screw.

At an angle of 90 ° relative to the shock device, charging carabiner is fixed. It contains staples that constantly perceive the effect of the spring. Non-working brackets are closed with a special plate attached to the case.

For the joint work of the drummer combined with the charging device, the trigger is responsible. It has in its composition:

waving lever;
powerful spring;
rocker.

To score a bracket, you must click on the lever. The bracket of the rocker will raise the drummer. The spring will stop compressing when the bracket will go into the mechanism of the slaughter. FROM big powers The drummer will hit the bracket, it falls into the base.

In fact, the main criterion for the normal operation of the construction stapler is the correspondence of several operations:

platoon drill;
feed brackets.

https://youtu.be/msq9 qg45va.

The work of the drummer should be synchronously with a rocker. If this did not happen, it means that the shot was made by the "fruit". In other words, the platform platform occurred and his triggering, but the drummer could not capture the bracket at that time. It is exactly what happens when the stubborn playground of the drummer is strongly flashes.

For repair, it will take some time. You need to hold the drummer in vice. An ordinary file sharpened the protrusion and give it an initial form.

Similar actions can be significantly extended the life of the stapler. You just need to make such a repair operation immediately after the pistol starts to work "in good". When repairing the plate, the drummer will shorten, as it will need to be told all the time.

Not so long ago, the upholstery works were performed solely using the hammer and nails. Mostly it concerned the production of furniture. But a special device has recently been developed, which helps to carry out fasteners in a more convenient way - this is a construction stapler.

If the chair with a soft upholstery or a sofa is turned over, it can be noted that the upholstery is fastened to special tightening elements, that is, brackets. The hammer and nails are gone, and now the upholstery can be built, not injuring fingers and much faster than it was before. The design is more convenient for work, but it can fail as any tool. Then, in front of the owner of the stapler, the issue of fixing the device.

Where to start repairing a stapler

Before starting to repair the construction stapler, you should familiarize yourself with its design, the principle of work. It will help better perform necessary actions And faster lead the stapler into the working condition. In addition to the staplers to fix the upholstery on the furniture there are other devices similar to the appointment.

Basically you can meet such varieties of staplers:

The hand stapler is easy to use and does not require careful care - you only need to periodically lubricate it.

Manual - in this group included mechanical devices with manual drive. They, in turn, are divided into several varieties, which it is necessary to choose depending on what working task.
The hammer of a bobbin is staplers who clog the bracket with a strong blow. This model has the speed of work higher than that of manual analogs, but the accuracy of the scoring is not very high. Most often hammers for clogging brackets are used in cases where the mounting of the runneroid or fixing the insulation during the repair. Here special attention is paid not to the accuracy of work, but its speed.
Cable staplers are designed for mounting cables that must withstand the load in 50 V. The diameter of the cable with which to work should not exceed a value of 7.5 mm. Choosing a stapler to perform such a task, it is necessary to take into account the diameter of the wire with which it is necessary to work. Such a device is most often used in cases where there is a large amount of work and it is necessary to fix the cable on the spot or the electrical network is paved. It can also be used during installation or repair of communications.
The usual model of the stapler, that is, the classic, equipped with a manual drive, pressed against the surface of the tool. Staples are clogged into the material by pressing the trigger lever.
The combined model - in this device combines the possibility of carrying out operations that are usually performed using different models Staplers equipped with a manual type drive.

In addition to the described models, there are other varieties of such a tool. Staplers can be professional and household. Professional distinguished characteristics such as ergonomics, extensive resources, lack of parts made of plastic. But there are also cons - such a wonderful device is worth a lot.

For regular repair work, it is better to purchase an electric stapler - its productivity is much higher than that of a hand-made stapler.

Electrical staplers - this kind of variety is widespread for household needs, performing a small repair. It is easy to work with it - just connect electricity. But at the price such a device will cost somewhat more expensive than the manual counterpart. If required, for example, just change the upholstery on the furniture, to acquire such a stapler is economically inexpedient. It is much easier to make a manual stapler - a significant application will not require this, and the savings are obvious. If we are talking It is better to use such a device regularly and often, it is better to purchase an electrical variety.

There are also professional pneumatic models. Staples are clogged by applying pneumatic strikes. They should not be used for household needs. Apply this method In production conditions, it is possible to install your own compressor. Acquire a better small compact model, which has dimensions of approximately like a very large suitcase. To perform work, you will need to organize a connection to the power grid. There are rather rather large in such fixtures, therefore, in the main data, it is enjoyed by specialists engaged in the repair of furniture at a professional level. Private manufacturers can also meet such a device.

Back to the category

Materials for work stapler

Expendable stapler - brackets. When talking about their size, the thickness is most often implied. But the width is different. Basically, such dimensions are used as 0.75 mm (thickness) and 11.4 mm (width). But much more varieties that have other sizes are produced. It is necessary to choose the consumable material depending on what the working task is. To create a good load, in case of repair, for example, you should choose an abscess. To fix not particularly tight material like polyethylene films, use braces with a good thick. The selection of the bracket when installing the cable is determined depending on what its diameter is.

The pneumatic stapler has a high price and is used mainly on furniture factories.

Working with the company device, it is necessary and consumables To it acquire the same brand. They are somewhat different from the usual with a similar size, they have good working qualities, made of stainless alloy and are not subject to corrosion. The surface of their galvanized.

They are well sharpened and comply with all the necessary drawing data, they have and warranty period. The presence of warranty confirms good quality and originality of the material.

Back to the category

It is convenient and pleasant to use the stapler. Staples are installed in a special store, the device is pressed to the right place and press the lever. Now the bracket is fixed. But sometimes the trouble happens - the stapler breaks. The bracket because of the charger does not fly out, on the spot, where they tried to install it, only a dent from the drummer remains. This means that the stapler needs an inspection, followed by the most common repairs. To repair the repair, disassemble the device in a specific sequence:

remove the regulating screw;
remove the spring;
remove the protective cover;
remove the pins and locking washers.

To bring the stapler into a working condition, you will need such tools:

screwdriver;
pliers;
a hammer;
file;
vice.

When everything is empty, you can see what happened to the drummer. Most often, the cause of breakage is the fact that the drummer body has a stubborn element. With it, the interaction of the shock mechanism and the trigger arm is ensured.

Drummer is the main work detail this device. It has a powerful pressure of a special spring, if necessary, its effort can be adjusted using a special screw.

The element called the charging carabiner is fixed with respect to the impact device at an angle of 90 degrees. It contains brackets for which the springs action is distributed. When you are not working, the brackets are closed on the plate fixed on the housing.

The correct operation of the charging device together with the impact element depends on the serviceability of the trigger system. It consists of the following parts:

lever waiting mechanism;
strong spring;
detail called "Rocker".

In order to knock down the bracket, you need to press the lever with force. The drummer will rise under the action of the bracket of the rocker. The bracket passes into the mechanism of the booze, and the compression of the spring stops. Drummer with power beats in bracket, it goes to the base.

Considering the working workflaire carefully, it is possible to conclude that the main criterion for its good work will be several interacting operations: this is the creation of the shock element and the smooth output of the bracket.

The drummer must work with a rocker in synchronization mode. If this is not the case, working the stapler, the person will pushing the lever. There is something akin to idling. Examined the descent, then it works, but the drummer does not capture the bracket. It is so that the device works in the case when the drummer spells a stubborn element.

The repair of the device is not particularly complicated and does not occupy a lot of time. Drumper clamp in vice. Then, using a simple file, the protrusion is sharpened, it is given the original form. Such actions help to make a lot of increasing tool operation. It will take regular implementation of this operation - it must be performed immediately as soon as the gun begins to work the nefple. It should be borne in mind that, since the shrimp plate will need to be constantly slightly told, it is gradually shortening.