Values \u200b\u200bof rollers for decorative plaster. How to apply stucco with roller. How to make rollers for decorative plaster

How to give the wall appearance brick masonrywithout putting a single brick? Such results can be achieved using decorative rollers that mimic brickwork. You will help you in this case several instruments: a flat roller under the brick, and decorative plaster. To this list, it is also necessary to add various auxiliary devices, by type of baths for plaster and so on, and most importantly - not a single brick.

Therefore, we need a roller to imitate bricks, as well as about the secrets of plastering such a tool, you can read in this article below.

Let's start with what is a decorative roller under the brick, and to solve which decorative tasks it is needed.

Without a roller, do not do if you want to give the walls a unique appearance without serious material and temporary investments. This technology came to us from the European countries, where the technology of coating surfaces with decorative plaster using structural rollers is used everywhere. The most widely used rollers to imitate brickwork.

IN Russian Federation The use of such rollers began relatively recently. And for obtaining such an invoice, various remedies were used. For example, after applying the layer of plaster, the drawings were applied with knives, nails or a major rope. Either special grid forms were used before applying the finish layer.

To date, there is a fairly wide range of building inventory, which will help to achieve incredible results, without resorting to the use of unpredictable tools. Will help you in this structural roller under the brick.

In the manufacture of such rollers, a hard rubber coating with a homogeneous and symmetric pattern is used, as a rule. As a result, the "drawing" of the brick is natural, and, when used qualitative materialsAt first glance, it is absolutely impossible to distinguish from natural facing bricks.

Another advantage is a wide range of color palette and plaster textures. If you want to get a conventional drawing of bricks - use standard plaster, and apply it with a roller under the brick. If you see in your design decorative brickThen choose the necessary texture of plaster, and purchase a roller, which in shape will be as close as possible to your designer solution.

Such rollers under the brick, at their price they have excellent parameters of stability, efficiency and reliability. Disposable investment in the purchase will be enough for several repair work in full. And with proper storage and proper use The service life increases several times.

Rubber from which rollers under the brick make high wear resistance parameters, and is practically not subject to wear.

As a result, a structural roller for plaster under the brick is great tool To decorate any surfaces, which has a number of indisputable benefits, such as:

high strength,

convenience and comfort in work,

cheapness,

huge selection of textured and decorative coatings With which such a roller can be used.

Professional roller for plaster under the brick buy you can in our store in Madex, it is also possible to order with the delivery of the Russian Federation through the online store at a great price if you are not in Moscow.

Decorative plaster is one of the most popular finishing materials today. The methods of its application are a great set, but not everyone can apply them when working with their own hands. Therefore, many prefer to acquire ready-made textured rollers.

Fact roller is used to give the walls of any pattern.

It is worth such a thing that is not suiced, not everyone will agree to give considerable money for a roller that will not be used constantly. Folk craftsmen came up with several interesting ways Making roller for decorative plaster At home.

How to make rollers for decorative plaster

It will take:

Fact roller can be made with their own hands from rubber.

• old roller;
• foam rubber, rubber, foil, foam;
• rope;
• universal glue;
• double sided tape.

The old textured rollers have reached this day, which were made of wood. If you have a wood thread skill, then you will not prevent anything to repeat this idea, but everyone will have to search for methods easier, for example, make a roller for decorative plaster from a regular rope. In this case, the basis of the old roller is taken as the basis, right to the foam nozzle, the rope of the cross will be coiled, in the form of a strip or arbitrary order. The thicker will be the rope, the clearer it will turn out.

Make rollers for decorative plaster can be made of rubber or foam. It is necessary to purchase ready rubber roller or rubber sheet with a thickness of at least 5 mm. With the help of a colored copy of the material, the drawing is transferred to the material, gently cut with a sharp stationery knife or scalpel.

If you want a chaotic drawing on the walls, then as a basis for textured roller, use a polyethylene package.

If you work on a rubber sheet, it is necessary to take care that the drawing at the junction makes a single integer. In this case, it is better to make a non-smooth connection, but a wavy. The finished rubber blank is glued to the roller with universal glue. Similarly, a roller is made for decorative plaster made of foam, the difference is only that the cylinder is cut out, then the drawing is applied and embossed.

If you want decorative plaster to have a chaotic drawing, you can use the following way. Take the usual plastic bag, carefully remember it, wrap on the roller in such a way that it is possible as much as possible folds, fix with a tape. In order to get a more prompt pattern, you can use buckwheat, peas, rice or foam crumb. The selected material is placed either the entire surface of the roller, or there are small fragments on a specific figure. These can be waves, twigs, flowers, etc. In this case, it is very important to use high-quality glue, otherwise small parts can be cut when applying decorative plaster on the wall.

Back to the category

How to make a factory roller from foil and silicone sealant

It will take:

Figure 1. Foil should be applied on the foil, and then attach to the roller.

• foil with a density of at least 50 MK;
• acrylic putty;
• knitting hook with rounded end;
• universal glue;
• thin rubber;
• silicone sealant;
• pistol for sealant.

Make rollers for decorative plaster can be on the principle of chasing. To do this, you will need to purchase a very dense foil (at least 50 microns). Unfortunately, it is very difficult for sale on sale, but there is a way out. Tight foil seal many products, such as sour cream. For the manufacture of small fragments of the pattern of this quite enough. On the pieces of foil are drawing, then pushed it with any suitable tool with a rounded head as in Figure 1. For this purpose, a knitting hook is perfect.

It is important that the distance between the elements is less than 5 mm, otherwise, when applying decorative plaster, the pattern will be quickly clogged.

After the embossing is done, it is necessary to fix the pattern with the help of an acrylic putty, it is applied to the part and immediately applied to the roller to give the part rounded shape, then remove and leave and leave to dry. After drying the putty, the bulk part is glued to the roller.

Make rollers for decorative plaster can be made of fine rubber and silicone sealant. First of all, it is necessary to get a suitable rubber, high-quality sealant and a special pistol. Rubber lay out on smooth surfaceThe selected drawing is applied by the marker. After that, they take silicone sealant and very carefully apply it to the drawing. In this case, it is better to take the pattern easier, for example, waves, stripes, simple flowers, leaves or circles.

If you have any textured objects (large buttons with a relief pattern, covers embossed, artificial leaves, gypsum elements), then you can do otherwise. The sealant is applied to the surface with a layer of 3-5 mm, make an impression of the selected object, pre-lubricated vegetable oil, leave until the material is complete, after which the part is removed. The rubber mat with a silicone pattern is glued to the finished roller. Using the tips outlined above, you can significantly save, make a factory roller with your own hands.

Plastering - Important Stage finishing work. Plaster not only Aligns and protects The surface of the structural elements of the building, but also gives them those or other textures and color.

Creating a plaster layer requires skill and knowledge, in particular, on the available arsenal of materials and tools, their properties, features, as well as when and in what combinations they are used.

Special rollers are used as hand tool With so-called "wet" plastering work. With their help, the master creates the last layer of coating on the surface, performing protective and decorative functions.

What is this tool?

Decorative roller is called rotated with a clutch with the working tool workpiece.

Is used for:

• applying paints and plasterectoons with a layer is different in the thickness;
• to make decorative irregularities laid, but still wet plaster.

Roller rotates around a metal rodconnected with the handle (the base structure is entirely called the "knob for rollers").

The roller consists of a rigid (usually plastic) base - cylinder with a cross-cutting hole and a working surface, applying roller elasticity, as well as the properties of the decorating tool.

Types of rollers by type of material

The name of each decorative roller includes information:

• about the material of the working surface;
• about the effect that it will create;
• and, sometimes, the properties of the recommended plastering composition.

More often rollers removable and characterized by their length and diameter(Sometimes diagonal), as well as the thick of the suitable handle.

Soft working fabric, gaining plastering, is often called "fur coat". So they say about the pile and foam rubber.

Solid and elastic rollers, whose drawing leaves a clear imprintMake rubber, wood or plastic.

Leather, fabric form soft, flexible canvas with changeable outlines. The hard roller, the higher the requirement for the smoothness of the wall.

Rubber

Rubber - Chemically persistent and non-toxic material, easy to clean, does not absorb moisture, it serves for a long time. Products from rubber are inexpensive.

On the non-sealing smooth textured plaster, a rubber roller with a convex pattern is picked up a drawing. From writing, created by any other tool, result differs the same depth and uniform distribution of pattern elements.

The ornament step is the greater, the wider the roller (width increases due to the base diameter).

There are rollers from the rubber sponge with a major porosity. They are good copier With applying plasters with decorating filler.

Wooden

The contact surface of the decorative roller from the wood is formed either by gluing parts to the smooth cylinder, or cut in it.

Due to the hardness of the material, excessive force applied to the wooden roller, may leave marknot only from the drawing, but also from the "background". It is not bad for the design of the border when the prints of the boundaries are not only allowed, but also make up part of the pattern.

Plastic

From cast plastic surfaces for embossing, from gas-filled - foam "coats".

The cast plastic working surface of the plaster roller is easy to care, but It happens "inaccurate" in the work With some compositions due to their hardness and sticking with a working mixture. By the service life of plastic is inferior to rubber, but has a smaller cost.

From thin plastic, soft or rigid, compressed, twisted or otherwise laid with the formation of folds and wounded on a rigid elastic roller, receive working surface For light stamping With an unobtrusive pattern.

Soft Dry Plaster Roller - Means creation of fine-grained surface, the relief of which is formed to a greater degree of decorative aggregate, rather than the form of the surface of the tool.

Do you know how to perform the finish putty of the walls on the wallpaper? This article describes the process of performing work with your own hands.

Leather

The decorating ability of the leather roller is achieved location of material Based on the formation of folds.

Depending on whether the folds are fixed with glue or freely located, the drawing itself is unique, on the wall will be released regular or the most natural.

The latter is "free" - option indispensable when creating marble texture. But without compliance with other additional conditions, there will be no such effect, the roller will create no less interesting, but more "cozy" drawing.

Hard fixed leather "wrinkles" will leave embossed unidirectional pattern, similar to the rubber fingerprint, but softer.

Pile

Roller with a porous working surface putting a plaster with roughness the smaller and more often than shorter the pile.

The surface can be similar to shale, or covered openwork nonwoven cloth. The effect depends on both the thickness and material of the pile and the type of plaster.

The pile is made of polyacryl, polyester, polyamide, and natural fur is also found. Such rollers often used for staining rough surfaces And to create a plaster coating with unobtrusive texture, not focusing on the volume of the room masking the irregularities of the wall.

By type of drawing

To determine the type of decorative roller pattern for plastering It is better to focus on his appearance than the name.

In the descriptions of this tool, the words "factory" and "structural" are always present, despite the fact that it is not synonyms, same tool You can find named and so, otherwise, and even two words at the same time.

Structural

Even with the existing confusion with terminology, it is easy to see that the word "structural" is usually present in the trade names of the foam rollers.

It is the spongy surface and captures aggregate commensurate And without drawing, "puts it in place." The decorative effect creates the structure of plaster.

Most of those rollers with which the plaster is directly applied to the wall are suitable for structural compositions. Their folds are called to "do not interfere" to work a major aggregate and, if desired, add relief drawings, imitating natural material.

Textured

Fact soft roller can spectally imitate The presence of inclusions in the plaster - that is, to create a coating with the texture of structural plaster.

The purpose of using textured rollers - posted surface view of any material: natural stone, wood crust, leather upholstery, wallpaper with drawing and mn. Dr. Example can be seen in the photo.

Undoubtedly textured - solid rollers with embossed or convex details. Their property is the predictability of the result. In the fresh plaster layer they leave a clear pattern of the same depth throughout the area.

To make the decorative effect of the maximum, the plaster filler should be thin.

The same rollers on the dried plaster leave the color pattern of paint. Such rollers are especially It is important to ride exactly in a straight line..

How to make your own hands?

The design of the painting roller is simple and familiar, but it is not necessary to make it a handicraft. BUT convert the work surface, or create a new one - the task of the satisfaction, not costly and win-win.

1. Wound Hardwater fabric (or wet, but dense), crumpled or twisted, add to the arsenal masters tool to create a natural pattern on plaster.
2. If the cover of the roller from the pile "Pass" wound with a noticeable step of beep, you can achieve multi-level roughness with directional pattern. You can also cut a specks or grooves, then the drawing of the relief "fur coat" will become more difficult, and the "Cellites" is anger.
3. Small smooth subjectsstacked on a roller with a thin working surface (for example, velor), or on rubber (for wallpaper), will leave a clear rhythmic pattern on the plaster.
4. Add additional surfaces, periodic level of relief Carved "cutters" in a foam roller or wound on it, with a large step rope. And whining it smooth, the roller is easy to get a tool for a clear embossing with a unique pattern.
5. Owning a wood thread technique Allows you to create a cliché with a complex and readable pattern. Translates the contours from paper to a tree copy paper.

How to apply decorative "fur coat" decorative plaster?

The plaster composition, including cement and small sand (1: 3, 1: 2, 1: 1), forms the coating "fur coat", if diluted to the consistency of thick, viscoerate colors and applied with a roller with a long pile.

The selection of the sand of slag or pumose sand is preferred (then the mixture is stirred at least 2 minutes).

The too liquid solution will be drained from the tool, and from the wall, and too thick - it will not cover the pile of the roller to the entire depth.

In the second case, you can apply a mixture with a spatulaAnd the roller will become a tool that gives a layer a little climbing plaster texture "fur coats".

Mixture with the addition of large aggregate requires the use of short-circuit roller, And diluted with water in the ratio specified by the manufacturer.

Decorative facade plaster roller includes the following steps:

1. The surface is purified from foreign materials and loose layers, from oil spots and spoken salts, irregularities are filled with leveling plaster.
2. The solid sharp tool is applied notches in the form of an oblique grid - on the wall.
3. The entire surface is wetted and soaked twice (brush).
4. The plaster is gaining a roller from a painting bath and applied to the wall, without pressure, as long as possible parallel stripes, without skipping.
5. To apply the second layer, it is not necessary to make a 1-2-day drying break, quite slightly align the sealing previous layer.

Alignment of the covered layer of the coat press the surface of the cork cover.

When choosing decorative rollers for plastering it is worth remembering that different patterns Nearby look ugly. At the end of work and roller, and the rod requires careful cleaning and drying.

Applying the decorative coat plaster: video instruction.

When it comes to beautiful finish walls, a good solution become rollers for decorative plaster, along with the use of this material as inner coating. Of course, the spectacular texture can be obtained and with the help of other tools, for example, inflicting light brummers with a narrow spatula, but it is most practical that it is roller. It remains only to find out which forms takes this tool, and what results with it can be achieved.

What are the rollers for decorative plaster

Initially, the decoration of the walls was performed solely with the help of paints, the plaster was needed only to apply frescoes on it. In this regard, the rollers were used only by paint, from fur, and later from the foam rubber, foam and others artificial materials. But over time, new techniques for decorating plastering coatings appeared, especially for the "Venetian", which required the use and radical change tools. All sorts of applicators, stamps, combs, and, of course, textured rollers, the basis of which became a foam large-scale prototype.

Based on materials, the aforementioned foam and foam, as well as rubber and leather rollers for decorative plaster are distinguished. More exotic options are possible, for example, homemade, carved from wood, that is, piece work. By invoice, the surface of the tool data can be mimicing marble divorces, brickwork, wood fibers and even a mine weaving. Also used to emboss simple and complex patterns, for which a repeating pattern is applied on the working surface, the end of which goes to the beginning. A large foam rubber creates a roughness of varying degrees of depth.

Textured rollers for imitation of various materials

If you want to create a relief on the wall surface, covering it with plaster, it is necessary that some structure be on the surface of the tool. To obtain protruding prints, textured rollers should be with recesses reflecting the selected pattern, if, on the contrary, the pattern on the wall surface should be squeezed, use the working surface with a relief pattern. In particular, if we need an imitation of brickwork, we take the usual smooth rubber roller, we make two ring channels, separating the working surface into three equal parts, after which there are transverse excavations on each of them in checked order. We get rectangular writing in each row, they will be bricks.

To simulate marble, it is enough to take a roller with a nozzle from the root skin or fabric. At the same time, during the operation of the movement, uniform, without releasing the tool from the surface as long as possible. Another way to get a structural roller with your own hands is to wind the rubber nozzle with a harness from the same material, making the turns in an arbitrary direction. Such an uneven working surface can be depicted wood fibers. Perhaps the direction of the turns will have to be corrected to obtain greater reliability of the texture. And finally, placing a piece of coarse tissue on the rubber nozzle, you can obtain imitation of textile upholstery. Almost any imitation can be obtained by a foam nozzle, applying the desired pattern on its surface.

Roller structural rubber for complex patterns

As a child, many are keen on the manufacture of rubber stamps, which can be used more than once, rubbing a graphite pencil rod or ink puff pens. Approximately the same is the roller structural rubber, only the pattern on it is closed around the cylindrical working surface. Once such rollers began to produce so that the hosts can do insistent on the wallpaper under the painting. However, over time, ready-made wallpaper with various patterns appeared, and a special device for the decor turned out to be unnecessary. It was useful tool to finish the walls of the plaster.

But if the usual nozzle with a small relief can be easily used to apply a sufficiently liquid decorative composition, is it suitable for this purpose a figured roller, with a pronounced pattern? Unfortunately no. The fact is that the textured nozzle with small irregularities allows you to capture a rather thick layer of the mixture, and in the process of its application layer it turns out somewhere thicker, and somewhere thinner. If very protruding figures of the drawing are cut on the working surface, only they are imprinted on the wall, the rest of the space will not be covered with plaster.

But this kind of tools are perfectly suitable for obtaining a picture on the already decorated surface. Not news that even the most fast-drying makeup freezes about twenty minutes. This time is enough to take into the hands of a roller and roll it on the surface ready plot. It is only necessary to observe one rule: the movement should be performed from top to bottom, with the same speed over the entire length of the decorating strip. The next passage of the tool must be completed close to the previous one, without indents and adhesion.

How to make structural roller with your own hands

Today, the tools for creating a textured pattern on a freshly mixed surface is in a free sale. They are made of rubber and have a strongly speaker over the base of the stamp in the form of a picture. However, it is much more pleasant to do something unusual independently, as a result, get a unique pattern. So what will be needed for this. First, the usual rubber roller for smoothing the wallpaper. Secondly, you need to find a dense thick rubber thick about a centimeter (you can take a couple of dozen erasers, but it is in extreme cases). And finally, we need glue for rubber.

From the rubber sheet or erase cut the figure, for example, a plant leaf. If the pattern fragments are sticking with large gaps, the role form does not play the role, otherwise it is better to make a fragment so that there is no difference, which of the parties will become a working one. The next element in the continuation of the plant theme will, for example, flower. You can make stems, buds, berries, the content of the pattern does not matter, the main thing is that it is continuous around the entire cylindrical surface of the tool nozzles. All parts are fixed with glue from the end to the end, the metal rod (BEGEEL), on which the nozzle rotates, is usually bent so that it does not completely prevent the change in the nozzle diameter.

The dimensions of machine tools consisting of handles, bohels (metal rod) and roller can be different: short, in the range of 30 centimeters, medium, from 35 to 45 centimeters, and long, from 50 centimeters and more. Special extension handles are also available, from 70 centimeters to 4 meters.

In order for the pattern to be as high as possible, it is desirable to round the working surface of all pasted parts. This will allow the figured elements into the surface of the plaster gently, without disturbing the print with sharp edges. Do not hurry and create a pattern right away as soon as the plaster covers the wall. The fact is that the fresh mixture will stick to the tool relief, clogged between closely located elements and, accordingly, remain on the roller. It is better to wait about ten minutes (or longer, depending on the used finishing material) To give the composition a little silent.

For textured painting of walls with a flat and flat surface, it is convenient to use such construction toollike roller. It seems to be nothing complicated in the use of the tool. After all, we all saw rollers, we all had to use it or watch others use it.

However, it should be considered what they are different types and are manufactured for certain purposes. It may complicate its choice when buying. That is why in this article will be given practical advicethat will help you in choosing this tool. And also learn what types of rollers for painting exist, to pay attention to when buying, and what is the feature of each of them. We will consider in detail required tools For textured painting of walls.

Some information about painting rollers

For all of us, this simple tool is not too angry. Its design is quite simple: the main detail of the tool serves as a roller, which rotates around the axis. The surface of the roller is covered with a material absorbing paint, carrying it on the surface of the walls. In order to work, it was easy and easy to work, the handle is attached to the axis. And practical is that such a handle is not constant, you can replace it for more convenient use.

The differences in painting rollers is mainly consigned in two moments:

1. The coating of the roller called the fur coat.
2. Roller width.

The quality, convenience, and the finished result of the completed work depends on such factors. That is why we will look at all its species, so that your work was not difficult, but I brought pleasure.

Type of fur coat

Nowadays there are such types of this material:

• threads;
• fur;
• foam;
• velor;
• flock and some flat surface;
• textured and textural rollers for decorative painting.

Fur

When painting walls, such rollers are universal, since the fur roller can be applied to the paint of any kind, even paint made on an organic basis.

Advantages:

• the composition is qualitative and evenly applied to the surface of the walls, which contributes to the light performance of their own hands;
• absorb sufficient number paints;
• when painting, the composition does not sprinkle;
• great for uneven surfaces, for example, for decorative plaster.

Materials from which pork are made:

1. Natural fur . Such material contributes to good absorption paint into the fibers and the distribution of it on the wall. The only disadvantage can be that the villus from time to time can fall out and applied to the surface with the paint. Often this happens with cheap, poor-quality rollers.
2. Polyacryl. The main advantages of such materials is a relatively low cost. Polyacryl is a worthy replacement of natural fur. However, it has a significant drawback - it is used for painting walls only on water based, and without any fillers with aggressive substances.
3. Polyamif. Compared to the previous material, this type is more durable and wear-resistant. That is why the fur coats from such materials you can use for the paints of any type. The disadvantage is that during the staining of the wall, the paint will sprinkle stronger.

Fur coats can have a pile different lengths. If you need to paint the rough surface, choose a long-pile fur coat if you need to paint the glossy surface, apply the fur coat with a small pile.

Tip! In order for your roller to serve as long as possible, carefully take care of him. After each application of the roller, take the time to wash it well.

How to do it right? To begin with, soak the roller in kerosene, and then in simple water. If you used a roller to paint the walls of water-dispersion paint, then the care of the tool will be even easier. In order to wash it, it is enough just to use a waterproof hose.

Vellar

Such painting is pleasantly performed, as it is applied to a beautiful uniform layer. If the surface was previously qualitatively prepared, the painted surface will look completely smooth.

Often in building stores Sellers say that such a tool is intended for specialists. Why? Because with inaccurate work, all defective places will be noticeable on the surface. Another disadvantage is that the burgers of the fur coat do not absorb a large number of Paints, which will make you regularly make roller.

Poropolone

The main advantage of this material is its price. For example, foam foam products can cost from 30-40 rubles. Such rollers can be applied to the color of the walls of water-dispersion paint. From the disadvantages, such moments can be distinguished: staining uneven surface, short-lived, splashes paint. But, despite such small disadvantages, this roller is not the worst option, especially when painting small square. For example, walls in the kitchen or in the bathroom.

Rolls for decorative painting of walls

What implies the concept of "decorative painting"? First of all, it is the application of patterns and drawings on the surface of the whole wall or for some reason.

To perform such work, there are two types of rollers:

Such a structural roller is able to apply a wonderful ornament on your wall. The photo shows how the finished result looks like.

Advantages of texture finish

When decorating walls in the room, it is worth introducing two varieties - the use of special texture paint or use different technologies Finishes. In applying the first option, you will have to go to the construction store and choose special paintwhich includes acrylic components. When finishing, such paint unevenly falls on the surface, so that you can get the granulation effect.

The textured painting of the walls has many advantages: work can be performed with your own hands, without having special construction skills, such a finish masks all the irregularities, the paint is not toxic, prevents the occurrence of mold, is stable in mechanical damage.

There is another embodiment of the decor - it is painting walls using stencils. Perform such coloring with a water-emulsion substance. This method of finishing has the following advantages:

• low cost of work;
• allows you to perform the drawing, in those places where you will be soul;
• large selection of color scheme;
• the ability to perform work with your own hands, etc.

Tools for applying textured paint

So, what can you need to perform decorative wall painting? These are the following tools:

It is clear that not all of this list you will use. But these are all devices that you can perform work. However, it happens that it is not possible to spend your money for different expensive rollers. What to do in this case? Do not panic, because in this moment You can show your fantasy, and make your original design premises.

Use self-made tools

In order to make a factory roller, you need to impose or glue pieces of foam rubber, fabric or cellophane to normal. After performing such a procedure, you can use such a roller to apply to them the water-emulsion composition on the wall or ceiling surface. This version of the decor will look very original and aesthetic. You can still use a wire wound on the video.