How to make a good soldering iron stand. The third hand and a stand for a soldering iron with your own hands. Stand and power regulator for soldering iron

The stand for the soldering iron is an indispensable attribute of the soldering station. It can be purchased at any hardware store or market. However, its cost is quite high. To save their own money, a stand is made for In addition to the financial issue, its functionality is considered. That is, it can be applied to various needs on the farm or in the workshop. There are a lot of manufacturing options. All of them differ in the complexity of the design and the amount of time spent.

General information

As mentioned earlier, a do-it-yourself soldering iron stand is convenient fixture which performs many functions. First of all, it is a protective surface, which prevents damage to property.

Before working with the soldering unit, it must be warmed up. In this case, the metal body is heated to high temperatures.

Soldering iron stand - what is it for?

A quality part is necessary for those people who perform a lot of soldering work. For the manufacture of such a device as a stand for a soldering iron, special skills and abilities are not required. The process uses simple and available materials and tools. The finished device is easy to handle. A homemade stand for a soldering iron should consist of individual elements. First of all, special containers are provided for rosin, flux and a department for mixing them. Some models are equipped with a box where small parts are stored. The soldering iron stand is suitable for any device, regardless of its power and degree of heating. In the manufacture of the structure, the location of these containers should be taken into account. Everything should be located so that it is convenient for the master to solder.

How to make a stand for a soldering iron?

It is unprofitable to buy ready-made coasters, as they are expensive and small. dimensions which are not suitable for all types of devices. Therefore, many users ask this question: "How to make a stand for a soldering iron with your own hands?".

Before starting production, it is necessary to prepare materials. To do this, you need to purchase the following components:

duralumin sheets, the thickness of which is 1.5-2 mm;
small wooden beam OK(can be used different kinds tree);
varnish containers;
two metal boxes.

When all these parts are purchased, you can start making the stand.

So, in the plate you need to make several holes. Containers for rosin and alcohol will be fixed on them. Cans are easy to install. Containers should be easily inserted into the structure, and also fit snugly against each other. After these procedures, it is necessary to make a support. It is made by bending the base.

If necessary, each person can make special racks that raise the structure a certain distance. This is done for convenience in the process. Preparatory work end on the processing of a duralumin sheet with a file or sandpaper. Corners should not have sharp ends.

Construction assembly

So, let's start assembling the stand for the soldering iron. The prepared support must be fixed to a wooden beam.

This can be done with screws. Next, the prepared small containers are attached. They are attached to the base with special glue or epoxy resin. Many craftsmen also install a small container between the racks. It can store small parts that will be needed in the process.

From wire

A wire soldering iron stand has gained great popularity among many craftsmen and hobbyists. It can be made from an ordinary tin can. In the process of assembling the installation, simple details are used:

tin;
pencil large diameter;
washers and bolts;
wire.

First you need to make a spring. The first thing to do is to purchase wire from the store. Some people remove it from other room fixtures. It should be thick enough to warm up to high temperatures the soldering iron did not destroy it. In addition, only high-strength material will be used. Ready product should spring.

We cut off the required length of wire and carefully align. To create a spring, a large diameter pencil is used. Holding the wire, carefully wind it around the pencil. The result should be a tight spiral. At its end, a special mount is made in the form of an eyelet. For these purposes, pliers are used.

The next step is to prepare the can. A small hole is drilled in its bottom.

This can be done with a nail or a drill. Next comes the stand for the soldering iron. The prepared spring is inserted into the jar and the structure is fixed with a bolt and nut. Washers are used to ensure a stronger mount. This method is pretty simple. Anyone can make a soldering iron stand. It does not take much time to make it, as well as special tools.

Soldering iron stand with power regulator

More and more people are choosing to use this species stands. Its essence lies in the fact that it is equipped with a special device that independently adjusts the degree of heating of the soldering iron. Therefore, the device does not overheat and does not fail. The stand differs from other types in that it requires an electrical connection to function. For the manufacture of a variant with a power regulator, it is necessary to take the following elements:

copper wire;
a small piece of plywood;
transformer;
LEDs;
details for fastening;
resistor;
wires;
socket to connect to the network.

After everything necessary details were purchased, proceed directly to the assembly of the stand.

To begin with, the size of the installation is selected. Based on this information, a base is cut out of a plywood sheet. Next, a transformer and other parts will be attached to it.

Fuse holder

The manufacture of this option does not take much time, effort, and also does not require large financial investments. A wooden beam serves as a base, on which the fuse sponges are attached. They can be various sizes. It all depends on the personal preferences of the masters.

Stand Benefits

First of all, the main advantage is mobility. Homemade coasters are used by people who often do soldering, working within several workshops. Such a design is not always at hand. However, it is easy to make. In addition, there is no need to carry rosin and tin separately in different containers, since now they are stored in special jars on a stand. So makeshift installations are popular not only among amateurs, but also among professionals.

How to make a simple model?

It happens that it is urgently necessary to use a soldering iron, but there is no stand for it.

In this case, there is no time to look for the necessary parts and run around the shops. Therefore, it is better to make a simple, but also robust design. There are many options, but there is the fastest one. The stand can be made in a few minutes. An ordinary wooden block will serve as a base, and screws or nails will serve as supports. They are driven into the beam crosswise. This forms a stand on which the soldering iron fits well and holds firmly.

Conclusion

When soldering elements, a stand for the device must be present. This accessory is expensive, so it is better to make it yourself. Such a process will not take much time, effort, and also save money.

The main tool of a home radio amateur is a soldering iron. Unlike other appliances, it cannot simply be placed on a table (workbench) during operation. Why? Right! He is hot. Therefore, you will need a special stand.

There are many different devices on sale, from a simple holder to a whole complex called a soldering station.

In most cases, a soldering iron is needed to perform urgent repair work. If you are not a professional "homemade" - the tool usually gathers dust in a box on the balcony, appearing once or twice a year. In such cases, many use the first object that comes across as a stand.

However, if you put in quite a bit of effort, a hand-made soldering iron stand will look no worse than a factory one. Especially if you regularly make electrical circuits.

Required minimum for stand

Stable foundation. Made of a material that conducts heat poorly, or equipped with legs
Soldering iron supports
Container for rosin (flux).

Additional options"

Tinning area
Solder container
Sting Cleaner
power regulator (can be of two types: smooth adjustment, or stepwise limitation for the time of a break in work).

Flipping through old magazines

In old Radio magazines, you can find drawings on how to make a stand with an economical load switch.

as a basis ( 1 ) a board with a selected middle is used, or U-shaped design from a strip of plywood and two bars along the long edges
A 220 volt relay contact group is located under the surface ( 2,4,5 ) with large collector areas. The wiring diagram transfers power either directly or through a diode. The radio element "cuts off" the half-cycle of the alternating voltage of 220 volts, reducing it to a value of 110
Through pull ( 6 ), spring-loaded ( 7 ) button ( 8 ) presses the contacts when the soldering iron is on the stand. Electricity is spent half as much, while the soldering iron almost instantly warms up to full power. The rod is attached to the console ( 9 )
The tool itself is located on the brackets ( 3 ) and ( 10 )
At the rear is a soldering iron socket connected to the relay output contacts. Connected to the input power wire food
Between the racks, they usually nailed a tin of shoe cream or petroleum jelly to store rosin

The main working tool of a radio amateur or equipment installer is an electric soldering iron, which cannot be used in the absence of a stand that is suitable in size and reliable in operation.

In amateur radio practice, a home-made stand for a soldering iron is most often used, the design of which is selected depending on the specific conditions of use.

As a rule, it consists of a base and two support posts, on which a tip and a handle-holder of a heated soldering tool are placed.

Make your own high-quality stand used for soldering various products and metal parts can be made from any improvised means that meet the following requirements:

reliability and stability of the base;
fire resistance of the material of the support posts;
availability of space for containers with rosin and solder.

The simplicity of the device in question does not mean at all that low-quality parts can be used to assemble it and treat it as something not very important.

On the contrary, for the manufacture of a stand for a soldering iron, you will need durable and reliable materials suitable for working at high temperatures, as well as exact calculation dimensions of the base with holders and containers placed on it.

The jars of rosin and solder attached to the base should be arranged in the order corresponding to the sequence of operations performed during soldering and not interfere with the work with the soldering iron.

Some craftsmen place soldering irons on such stands along with a power regulator, which significantly complicates the design of the entire device as a whole.

Unlike small-sized factory samples, self-made stands must have dimensions sufficient to accommodate all of the above elements.

Sometimes such devices are equipped special holder for a soldering iron (the so-called "third" hand), which allows you to fix the workpieces or parts being processed. One of the simplest product options is a crocodile holder.

Simple version

To assemble a simple handy stand with a minimum of parts, you may need the following consumables:

a wooden flat blank made of beech or oak about 25 by 12 cm in size, necessary for making the base of the soldering iron stand;
duralumin plates with a thickness of not more than 1.5 mm;
miniature metal containers (brass cups from phone call old type).

After all this material is prepared, you can proceed to the assembly of the soldering iron stand itself, starting with the preparation seats under containers with rosin and solder.

In the case of using brass cups from the ringing device (bell), they are simply screwed to wooden playground at a predetermined location.

After that, triangular or oval support elements are made from a duralumin plate (the distance between them is selected along the length of the soldering iron).

The supports formed in this way are attached to the base of the stand using self-tapping screws or large screws.

If necessary, the height of the supports for placing the soldering iron can be increased by lengthening them due to short metal racks with threaded ends.

All prepared parts should be carefully processed with a file, and then clean their surfaces with sandpaper, which will smooth out sharp edges and remove dangerous burrs.

Third hand holder

For soldering individual parts or products, it is very convenient to fix them in a certain position, freeing the hand in which the soldering iron should be located. For these purposes, a special device is used, which is sometimes called a “third” hand soldering iron stand.

To assemble it, you will need the materials and tools shown in the above photo. The list of required parts includes crocodile clips, holders from decorative candles and any suitable spring.

Such a design can be based on a Chinese-made product equipped with a magnifying glass and containing all the necessary elements.

When assembling such a stand, first, at some distance from the center of the base, a spiral holder for a soldering iron is attached, after which holders from under the candles are inserted into the pre-drilled niches.

Before installing them, it is necessary to pay attention to the wall thickness of the cups, which is chosen for reasons of optimal thermal conductivity. And only after that it will be possible to insert them into the already prepared niches, pre-lubricating the bottoms with glue, and then align the edges flush with the plane of the wooden base.

After installing the containers for rosin and solder, it will be possible to fix the "crocodiles" by crimping them around the spiral. The height of their location is chosen in such a way that working with the soldering iron and the part does not cause any difficulties.

For the convenience of soldering, the spiral design can be provided for adjusting the position of the clamps vertically.

If necessary, a magnifier (magnifying glass) can be added to the assembly stand for the soldering iron. However, the experimental operation of such devices has shown that the simultaneous installation of auxiliary clamps and a magnifying glass on a stand creates certain inconveniences in working with them.

The choice of options for making a stand with your own hands is quite diverse, and depends on the materials that are at the disposal of the master.

If you don’t want to do it yourself, you can always buy a ready-made stand at a soldering supplies store.

The topic of soldering iron stands is quite well disclosed on our website. How is my stand different from others? — I tried to make it as compact, convenient and functional as possible. Do you want the same? - Please under the cut!

The main feature of this stand is the built-in regulator. was inconvenient in that he was constantly lost and mixed with another bunch on the table. This one is tightly screwed to the stand, it will never get lost and will not jump around the table.

The new one is better than the old one in that it has smooth adjustment and operation indication. Here is the schematic I used to assemble the controller:

Diode bridge - any that can withstand the mains voltage and the current consumed by the soldering iron. (the formula for calculating the current is Soldering iron power / Mains voltage) A suitable diode assembly or bridge can be pulled out of the input circuit of a computer PSU. Instead of a diode bridge, you can use a diode, then the adjustment range will be from 50 to 100%.

Fuse F1 is desirable, but not required.

Switch S1, S2 - Bipolar toggle switch with middle position. In the middle position, the soldering iron is off and the HL1 LED will not light. In the position indicated in the diagram, the power of the soldering iron is regulated by the trimming resistor R3, in the opposite position of the toggle switch, the current goes directly to the load, bypassing the regulator.

I made all these muddles personally for myself, and it is not necessary to repeat this scheme exactly. Yes, a suitable scheme can be gleaned from there.

Regulator board:

To cover the giblets of the regulator from external influences, I made a plastic case, bent the edges with a technical hair dryer:

WITH electronic stuffing We figured out the regulator, now we move on to creating the nodes of the stand itself.

In order not to lose various small items and store solders, I made a small box of tin, the corners of which for strength:

The soldering iron stop itself is, in my opinion, the most successful design. In order for the soldering iron to hold well in such an emphasis, when inserting it, its center line must be below the stop horns.

When soldering, a fixture is often necessary, but you don’t always need to clutter up the table with such fixtures - just attach a crocodile clip to the stand, which is fixed with a screw:

To clean the tip of the soldering iron I use metal sponge for washing dishes, which will be located in a box made under it with edges:

Stand base - Rectangular chipboard:

Milled recess for rosin:

I crumbled rosin from a jar into the recess and warmed it up building hair dryer not to fall asleep:

We begin to attach the above nodes to the base, further commenting is unnecessary:

The fixing of the main nodes is completed.

To prevent the stand from rolling on the table, reverse side glued rubber rounds:

Well, so that everything would be according to Feng Shui, we glue identification badges on the regulator body:

Do-it-yourself soldering iron stand is very convenient and practical device, which is a kind of table and performs a protective function. Before soldering, the soldering iron must be warmed up. When heated, the case heats up very much, which is why it is worth using a stand to protect any items.

The design of the soldering iron stand: 1 - base, 2, 4, 5 - contacts from a relay type MKU-48 for 220 V, 3.10 - support posts, 6 - disk, 7 - spring, 8, rod of the moving contact Kp 9 - square , D1 - diode type D7Zh.

The need for a soldering iron stand

A high-quality and practical stand for a soldering iron is needed by all those who deal with soldering. You can make it yourself from improvised materials, you just need to have certain skills and certain tools. A homemade stand for a soldering iron is quite simple to manufacture and operate. In order for a thing to be convenient, it must have certain nests designed for containers with flux and alcohol, boxes for rosin and solder, as well as a place to display some details. Homemade stand for a soldering iron it is possible to use with a tool of any power. When making a design, it is necessary to arrange all the containers in such a way that it is convenient to solder.

Back to index

How to make a stand for a soldering iron?

The factory options are very uncomfortable and small, so many are wondering: how to make a stand on your own so that it is practical? Manufacturing must begin with the choice of materials. Must have:

duralumin sheets about 1.5 mm thick;
a small wooden plate measuring 50x40 mm, made of oak or beech;
two small metal boxes with lids;
bottles of varnish, preferably the same and with brushes.

When everything is ready, you can start manufacturing. In duralumin plates, it is necessary to make holes for bottles with flux, alcohol so that they are inserted freely enough. The holes for the jars must be made so that they fit very tightly. After all the holes are ready, you need to bend the base a little so that you can make a support.

If desired, you can make special racks so that the stand is a little higher and it is more convenient to work. All details must be carefully processed with a file, and then with sandpaper, so that the edges and all corners can be rounded.

When everything is ready, you can start assembling. The lower support for containers must be screwed to the upper support and the wooden platform. Using epoxy, you need to glue jars and bottles into the base. In addition, you can take a small rectangular jar and place it between the racks on which you can put the device. In such a jar it is very convenient to store various devices that are simply necessary during soldering.

You can make a stand for a soldering iron from an ordinary tin can. For its manufacture you will need:

a soldering iron stand can be made with a nail or drill in the bottom of the jar by making a small hole for the bolt.

wire hanger;
washer;
bolt with nut;
marker;
tin.

The wire taken from the hanger is very convenient for making this type of product, because it has good strength, but at the same time a little springy.

For manufacturing, it is necessary to initially bite off the wire with pliers on both sides and align well. With one hand, you need to support the wire, and with the other, wind it around the marker. On the resulting spring with pliers, you need to make a small eye.

Make a small hole in the bottom of the can with a drill or a nail. After that, you need to assemble the entire structure. It is necessary to insert the spring into the prepared tin can and tighten it with a bolt, nut and washer. So in an easy way you can make a very convenient and practical stand for a soldering iron.

Back to index

How to make a "smart" stand for a soldering iron?

You can not only make an ordinary soldering iron stand, but also make a “smart” model that will independently regulate the heating level of the device. A smart stand for a soldering iron must be plugged in during operation, and it will regulate the level of heating of the device, thereby protecting it from overheating. Thus, there will be no overheating, but there will always be a readiness for work. To make a stand for a soldering iron, you need to take materials such as:

The finished structure is assembled by tightening the spring inserted into the box with a bolt, washer and nut.

double socket for outdoor installation;
a piece of single-core wire, preferably copper;
plywood;
transformer;
connector for fixing parts on a plane;
LEDs;
resistor;
switch;
wires;
pin.

After all the materials are prepared for work, you can proceed to the direct assembly. First of all, you need to determine the size of the base itself and cut it out of durable material.

After that, you need to make an outlet, for which it is worth drilling holes for the outlet socket, installing LEDs and a switch.

Then install everything in its place and solder the necessary wiring to each other.

From the socket through the switch, you need to bring the wires out for the subsequent connection of the transformer, then you need to bring the wires through the socket of the socket and attach a resistor, a red LED, which will signal that the transformer is turned on. All this must be carefully fixed on the base. In addition to making a stand, you need to make a holder for the heater. To make it, it is necessary to fold the wire, preferably copper, in half and attach it to the base. It is worth taking care of special boxes in which rosin and solder will be stored. Boxes should also be screwed to the base.

All bare wires should be wrapped with insulating tape and we can assume that the stand for the soldering iron is ready. You can get to work and be sure that the heating device will work perfectly, without overheating at all.