Plastic pipes for the well - advantages and use. Independent welding of plastic pipes of large diameter pipe bender manual for steel pipes drawing

After laying communications in the house there are many trimming of pipes and fittings. Using them in the farm, you can create original crafts and useful products. And after their painting, your guests will never guesse, from which the design is collected. Let's find out what you can do from the remnants of PP and PND pipes.

Designer furniture from pipe residues

Famous designers create masterpieces from undergraduates. Let's try not to lag behind them and provide yourself with free and original furniture from unnecessary pipe trimming.

Cells for shoes for saving space in a small corridor

The sewer pipes are more suitable for their diameter. A pair of shoes should be free to fit into the future cell, and choose the length of the biggest pair. If you have children, you can make cells to make different depths and glue in the form of a pyramid, the bottom is long, and on top are short. Before gluing the pipes, paint or plunder them. Such cells are not afraid of moisture and do not allow pairs to mix.

Foldable liner dryer from thin pipes

With several pipes and fittings, you can collect a folding dryer for linen. It is easily installed on the street, and at night or during the rain is entered into the house.

To do this, you will need:

two turns;
compounds;
four tubes for legs;
one tube as the upper crossbar;
several pipes on which things will be dried.

Please note that drying jumpers are made of different lengths. On the one hand, they are slightly smaller, since one pair of legs is attached inside the second, narrowing the gap between them.

Safe staircase for children or entry limitant for animals

The owners of two-storey houses that grow kids are often experienced for the fact that the child can fall from the steps. To protect children, it is enough to put a small wicket from plastic pipes. It is also suitable for installation in the doorway, if there are rooms in which dogs should not come.

Rack for books and technology

For expensive instruments or a large number of books, it is better to choose sewer pipes, they are stable and withstand heavy weight. The shelves can be embedded directly in the pipe walls or place on jumpers. Those shelves that are placing on the crossbars on the sides - fasten with silicone or glue so that they do not slip with a random push.

Stand for electrical appliances in the bathroom

It is enough just to find a pipe with a suitable bend and paint it into your favorite color. If you want to apply an image, but do not know how to draw, just cut pictures and, applying them to the product - secure varnish.

Original lamp on the floor or bedside end

To create such a lamp, it will take a pipe, a cartridge with a platform, a wire with a fork and a solder or selo. Inside the pipe stain in the color of the ivory, and outside - into black, brown or other dark tones. For chalk, apply the contour and do holes on it.

It is better if you use a soldering iron or device for burning and do not through, but slightly molten points. Then you can adjust the brightness of the pattern. In thin points, the point will be lighter, and in a slightly staged darker. Such points can be painted and your luminous silhouette will acquire various shades.

Bed of pipes and fittings

To create the bed, you will need a lot of pipe trimming with a large diameter and the same number of connections. All connections are recommended to cry. You still won't disassemble it, but the movement of the bed without glued particles can end in full collapse of the whole design.

You can, of course, collect a simpler model, without rounding the back, then long trimming will be useful, but it will not be so strong.

Trimming from pipes to help gardeners and livestock

Most of all useful crafts from plastic pipes will be assessed by people engaged in garden or pets containing domestic animals. They are easily clean and easy to maintain.

Organizer for instruments

Many of us store the tools in the box or hang on nails in the wall. The first way is inconvenient due to long searches, and the second due to lack of space. Plastic pipes allow you to "spend" tools perpendicular to the wall. To do this, it is necessary to make slaughter cuts and consolidate the cells from the tubes on the wall.

Trolley from the tubes

In addition to pipes with fittings, you will need and wheels. The basis can be collected in different shapes and sizes. In our case, an option is shown from very small trimming, which cannot be applied in another area.

Autocorry for poultry

People growing chickens are familiar with small feeders who are installed with grain cans. The presented feeder acts in a similar way. Under its own weight, grain from the pipe wakes up in the feeder.

Pyramid for seedling and growing strawberries or greens

You can also collect the foundation for fastening pipes, and instead of one oblong slot to make round and insert plastic cups there. Then the roots will not go off among themselves, and the seedlings will be easier to remove. You can put a vertically several pipes, making a small slope. Over the entire length, make slots and set turns instead of pots.

Sprayer for lawn

Of the four pipes and turns, the square is collected. A tee is mounted on one of the pipes and an output to the hose is made. In each tube there are small holes, at a distance of 5-10 cm from each other. When the water is applied, the pressure will create small fountains for irrigation of the lawn.

Slowing the remains of pipes of different diameters on the rings, you can collect openwork arbor. It looks great in the cold season when the plants are standing without foliage, and in the summer, at the moment of towering the rings of curly plants.

Dummy

The pipes themselves have a neat appearance and burnouts are not afraid. If you have a lot of trimming, collect fence or railing from them. From criminals, he is certainly hardly saved, but as a fence between neighbors is quite acceptable.

Bicycle parking for the whole family

Lovers of cycling are often faced with the problem of their storage. By installing parking from plastic pipes in the garden, you will not have to drag bicycles more from place to place or lift them on the wall.

Almost all designs are very simply and, if necessary, can be disassembled and transported. When choosing trimming for modeling, pay attention to the rigidity of the pipes. Some are able to withstand a person, while others are suitable for decor or easy operation.

To perform construction and installation work, especially when it comes to pipelines, pipes are often required with a different bend angle, and the use of fittings may not be justified at all.

Flexible pipes in such cases is carried out using pipe bend. These and portable, industrial and home use.

Building articles

Device and principle of manual pipe bending

Hand-made pipe bender in design and the principle of operation is quite simple, so the homemade craftsman may well conduct with its manufacture own. The main elements in any device for flexible pipes are the pressure plate. It presses a special mechanism with a certain effort, and it transmits an effort on the pipe processed.

As a pressure mechanism, both an electric motor or a hydraulic pump and a spring with retainers are used.

To perform bending, the corrugation is installed between the pressure plate and several shafts that perform the function of stabilizers. Also, with the help of the shafts, you can adjust the bending radius, since their position is adjusted.

So, for the bend of the pipes on a small radius, the shafts are located close enough to each other, and if it is necessary to increase the radius, then they are transferred away from each other.

For the bending of the round tube on the pipe bending the shapes are installed in the shape of a crescent.

Manual device

The homemade hand-made pipe bender, with which the flexible round pipes are carried out, is two flowing pulley, one of which is fixed motionless, and the second rotates around the first diameter of the processed pipe. The principle of his work is simple: Between the two pulleys, the pipe is laid and by rotating the movable pulley bending a round tube to the desired angle.

Manual pipe bender in the hands of a skilled host may be needed at any time, because it is thorough to fit it thoroughly, so that it can be bent pipes of various diameters.

For such a design, two triple pulley will be required instead of single: one pair will be used for flexible pipes 1/2 ", the other is for pipe 3/4", and one for inch pipes.

In the market, it is unlikely to buy such devices, so they will need to be ordered in a turning workshop. At the ends of the shafts, an outlet is made, which coincides with the half-diameter of corrugations.

Another important point that needs to be taken into account in the manufacture of shafts - stationary pulley in size should be minimal, since it depends on the minimum possible radius of the product bending. The optimal size of the movable shaft exceeds the diameter of the stationary.

Pipe bender design sequence

So, now directly about the stages of the work that are performed independently:

after the shafts are ordered, proceed to the manufacture of the base under home-made pipe bending. A thick metal plate (at least 10 mm) square shape is suitable for it. To mount the base to the table, it is necessary to drill four holes in the corners of the plate, or weld to the metal post closed in the floor;
in the center of the plate using welding fasten the pin of the same diameter as a small triple shaft;
the next stage It is necessary to make a rotary mechanism. For this, three metal plates are welded in the form of the letter P (width of the plates of more than 50 mm), and the height of the structure depends on the diameters of a large and small shaft: a completely movable pulley and half of stationary should fit in this altitude;
to mount the shafts, you will need to drill a few holes. The legs of the letter P are from each other, slightly greater than the height of the shafts. To the upper stack of the design, a handle is welded, a length of about 25 cm, to which the tube-lever is subsequently worn;
the large pin is mounted primarily and is fixed with plintes behind the plate in the form of the letter P, and the small shaft is put on with the whole design;
for the hardware stopper equipment, another pin installed vertically welds. He will serve as a stop.

The second method is similar to the previous one, only Metal hooks are used as a template, which secure on top of the plywood sheet along the alleged bend. The advantage of this design is that the hooks can be rearranged to change the pipe radius.

Advantages and disadvantages of manual pipe bending

The main advantages of manual devices:

It has small overall dimensions and weight. Flexible pipes with them are possible almost anywhere: in the workshop, in the country area, in the garage or on the construction site. As a rule, the need for a pipe bender for round pipes occurs in those places where engineering systems are paved.
Another advantage is that with the help of such devices, flexible pipes made of soft metal or.
Manual aggregate is quite mobile: if necessary, it can easily be transferred to any place.
Even the most inexperienced user will cope with the work on the handbreaker: the principle of his work is so simple that it is simply impossible not to understand it.

However, along with advantages, there are also disadvantages of using such an instrument. One of the most important: no ability to generate a large diameter pipe. Also predica will be flexible thick-walled.

Each owner of a large garden plot or a small summer cottage, at least once in life (at a minimum), it may be necessary for pipe bender - a device for flexing the profile pipe.

For example, it may be a blank for a greenhouse frame or a canopy, arbors, or any other metal structures.

On the base for the sale of metal, and in other production, devices of factory manufacturers are usually used, but this pleasure is not cheap. To save your budget for more pleasant spending, it is more profitable to make the manufacture of the device into manual, on your own.

For this design, as they say, "a lot of mind is not necessary," and there will be no deficit in the details either, the drawings of the pipe-bending really create yourself.

Versions of pipe-bend

You can bend the pipe "home" way, fill the pipe with sand, heat up to red with a soldering lamp or a gas burner, then bending the pipe. This method is not recognized as priority among masters, it is laborious and does not give sufficient accuracy, there may also be chances and deformations.

To get a perfectly bent pipe, with the observance of norms and specified parameters, do not cause damage to the source material, the masters are used in the work of specialized pipe bending.

Large popularity purchased lever type pipe begins. This elementary invention works on the "lever" principle - the force concentrates in a certain place, and the bend merges with the form of the template you created, which can most often be removed and replaced by another.

Most often, the set of such structures provides a pair of additional templates for pipes of different diameters. There are similar in the design of the aggregates, manual pipe bending, drone or arbaltny, they allow you to bend short sections of round steel pipes, exposing only cold processing.

Arblet devices are very compact, and are valued in the field of installation and engineering communications.

What is the work of the pipe-bending

The principle of operation is completely simple, it consists in heating the pipe, the pipe heats up to red and becomes very plastic, pliable to changes. Each type of pipe bending has its own range of features.

The main functions are the quality of bending and the ability to bend pipes of different size and diameter.

With the help of additional rolling devices, the bending of the larger diameter is achieved. The device functions using shafts, included three of them.

Guides and pressure. The pipe passes through the moving elements, the degree of bending is set to force the clamping roller. If the radius of the curvature of the finished product turned out to be small, the procedure should be repeated.

Bending pipes by template

In most cases, the simplest option suitable for absolutely all masters, even beginners, is a pattern of wood. The boards are chosen over the thickness of the flexible pipes, be sure to leave the stock of the board in a couple of centimeters.

So that during operation, the profile did not drive from the template, on the ends left a slope. The pattern is rigidly fixed on the floor or other stable surface, the mounting of the pipe is carried out nearby.

The profile is inserted into the gap between the template and the focus, smoothly and gently pressed onto its other end, pressing the pipe to the template. The winch either the lever will make the job easier.

A huge plus of such a process, saving money and simplicity of execution.

Note!

Any device has drawbacks, and this method is not an exception. The bending is not accurate, poor quality, as well as the template will be disposable (used only on one diameter of the pipe).

Pipe bender snail

In the stamping of the same billets with a large circulation, a small radius of curvature, an indispensable pipe bender-snail.

His dignity in small-sized sizes and ease of management. The disadvantage will be the limitation of the radius of rounding, only not large sizes.

Rolling tube

Niche of versatility and practicality occupied fixtures performed in manual - rolling pipe bending (bending machines), any bend angle can be made on such machines.

The configuration is not particularly different from other models, they also have the base and shafts. The movable roller is tuned, and stretches its rotation of leading shafts.

Note!

Pressing can be enlarged with a winch, levers or an electric drive. However, for the production of the house, such a design is quite complex in execution.

To reproduce such an aggregate, a lot of turning and welding works will be required. If you still decide on the manufacture of such a model, it will last you for a long time and will delight the functionality.

How to make pipe bending with your own hands, the question in the modern world is quite relevant. To facilitate the task, you can find a photo of pipe-bend on the Internet to roughly understand how it should look.

There is also many drawings of pipe-bending, which are easy to use. After reviewing all the information and evaluating your strength and the presence of the necessary components, quietly proceed to work.

Photo pipe bending do it yourself

Note!

Owners of private houses, as well as many home masters, are required for the manufacture of various elements of arched structures and pipelines bent under certain corners of the pipe. For this, they use industrial, and more often homemade pipe benders for a round tube. Professional factory devices for flexible pipes are expensive, so often such devices are made on their own, which saves.

Device and principle of pipe bending

The procedure for bending a pipe is practically not difficult, but requires special attention. In the process of bending, it can get defects in the form of stretching the wall and reduce its thickness at the bend place, which will lead to a decrease in the strength of the pipe. Also, the place of bending can change the cut configuration and instead of a round cross section to take the form of an ellipse, which significantly reduces the internal bandwidth of the liquid passing through the pipe.

Design features

So that defects in bending were minimal, choosing or manufacturing pipe bender, you need to understand how it works. The manufacture of a pipe bent device consists of three stages:

Such manual devices for disintegrating tubular blanks may have a mechanical or hydraulic drive, while these two options are perfectly suitable for a domestic workshop.

The principle of operation of almost all pipe bending devices is the same. The billet is fixed in a special device and under a certain force takes the desired bend angle.

There are various pipe bending devices, and, of course, each of them uses its own system of power. For example, in devices of an arbal or hydraulic type on a flexible section of the pipe affects a point force.

According to another scheme, the bend is performed using several rollers, between which the workpiece is rolled, a certain bend angle is obtained. According to such a scheme, pipe benders are operated, equipped with special inserts for pipes (dulls).

What do you need Dorn

To figure out, for what purposes are dorn, you need to know what can happen with a pipe during its bending, if not to use Dorn. For example, when the billet is bent into some of its sections, two opposite forces act in the bend place:

Compressing the wall of the inner radius, in which the metal, deforming, forms a wavy surface (corrugation).
Stretching. At the same time, the metal wall of the outer radius of bending is stretched, due to which it is done thinner. Naturally, it can almost up to 50% can weaken the strength of the pipe on the stretch of the bend.

Especially strongly, if not to use Dorn, thin-walled copper, aluminum and other tubes made of soft material can be deformed.

For the Dorn inserted inside the pipe before flexible, steel springs are usually selected for the inner diameter of the bended pipes. Sometimes the surface of the springs to ensure a better stabilization of the pipe walls, is covered with polyurethane.

Types and manufacture of bending devices

Ways to bend the pipe, not so many, but fixtures, to perform these actions there are quite a large amount. At the same time, they can be of a variety of types. In order to make proper pipe bender for a round tube with your own hands, drawings can be made on your own or free download from the Internet.

According to the principle of impact on the harvesting of a round tube, to give it a bend at a certain angle, there are pipe benders of various types.

Model of arbal type

These models of pipe bending devices are powered by hydraulic or screw drives. In the process of processing the workpiece, the model bends in the form of an arballee shoulder, from which the name of the bending device has gone.

The design of the arbal tube in the manufacture has some difficulties, but its strength and technical capabilities are quite large. The adaptation itself can be done with several functions, for example, to use it as a bending machine and a hydraulic press.

Depending on the design of the rigid metal frame, the machine can operate in a horizontal position (the jack or other power device is located horizontally) and in the vertical.

The design consists of a rigid frame and two rollers, fixed on special racks welded to the platform. In the center between the racks there is a jack, and clamps are fixed to the rollers, which ensure the free fixation of the workpiece, which is placed on them.

Puinson for pipe bend (shoe, pattern) can be made of old rollers, pulleys or curved and cut along pipes.

The work of the arbalt machine is made in this way.:

On the rollers is placed and fixed by clamps blank from the pipe.
The jack is fixed with a shoe (template with a certain bend angle).
The jack is pressed on the center of the harvesting by the shoe and smoothly bends it under the given angle.

On the same method, you can make a small manual pipe bender, with which it is easy to flex a durable thick-walled pipe of medium and small diameter. For this purpose, it will be necessary to purchase a hydraulic jack of small sizes, two rollers, make a punch and a durable T-shaped metal nozzle for the jack.

The whole design of the "arbal" mechanism should be with a large margin of strength. Otherwise, if a billet from the locking brackets occurs under the pressure of the jack, the operator may be injured.

Roller-rolling system

Such pipe bending models are also called roller. With this system, you can bend round or profile pipes, as well as steel reinforcement for a large radius. An ideal device for billet arcs under sheds or greenhouses.

The main elements of this kind of fixture are three metal rollers, selected under the diameter of the bent pipe blank. The billet is placed on two extreme rollers and the third, located in the center, rolled through the pipe. Under its effort, the detail gradually begins, acquiring a certain radius of bending.

The system can be driven using a hand handle or an electric motor through a special gearbox for pipe-bend. The quality of the product obtained, which has been treated on this device is quite high, and the pipe itself, contacting the rollers from the metal, almost does not receive damage.

The advantage of rolling tube - in its small sizes, thanks to which the tool occupies little place in any domestic workshop and it can be easily fixed on a workbench or wall. And due to the fact that it is made entirely of metal, the workpiece in the process of its bending is possible to facilitate the work to fit the soldering lamp or gas burner.

Simplest device

To perform urgent work when manual pipe bender is required for a round tube to quickly exhaust the angular knee, for example, for home water pipes, you can make a simple bending device using a screwdriver. To do this, make a lever from trimming a metal round tube with a diameter of about 32-42 mm or thick, desirable smooth fittings. The length of the lever must be within 1-1.5 m, depending on the bending of the workpiece.

One of the ends of the lever is welded a ring from a thick-walled pipe cutting width of about 30-40 mm. The inner diameter of the ring should be greater than the outer diameter of the billet prepared to bend.

Instead of the ring to the lever, you can breed two rods from a thick smooth rod. The rods are welded perpendicular to the lever and in parallel to each other. The distance between them should be greater than the external size prepared for the bending of the workpiece.

rozzess bending is as follows:P

The billet is stacked on a solid smooth surface, it can be asphalt, concrete floor, railway panel or thick board.
The tubular blank prepared to the bending is loaded into the ring of the manufactured device or inserted between its pins, after which, acting on the muscular strength lever, its bending is produced.

Type machine

The pipe bending machines of this type differ from other bending devices by the fact that the clamping roller presses the workpiece directly to the template itself, as if wrapping the pipe to it. This allows you to bend from the billets of ring-shaped and spiral details, which is absolutely impossible to do on ordinary pipe bending machines.

During operation, the roller itself is in a fixed state, but the template to which the end of the workpiece is rigidly fixed, turns around its axis, winding the pipe, which is why the machines of this type are called.

The drive on such devices is most often electrical, since to twisting the pipe in the ring requires a lot of effort. The mandrel for the template must be removable, otherwise it will be quite difficult to remove the billet from it. The template can be made of wood, textolite or metal.

The advantage of the winding machine is its simple design, and the disadvantage - in some restriction of the size of the template and the need for a powerful lever.

Conductor of wood

This design can be considered a trimmed device, and the difference is that there is no pressure roller. To make this device, you will need a thick plywood or board, you can use the workbench or a massive slab from the chipboard.

From a thick board, a template is made, in which one side has a rounding under a certain radius. It is rigidly fixed on the edge of the workbench with this calculation so that around it it was possible to freely wrap the workpiece cooked to the bend.

The end of the workpiece can be fixed by primitive wooden focus from the bar or trimming the same board from which the template was made. The bending of the pipe is made with the help of muscular power smoothly, without sharp movements, then its damage will be insignificant, and the acquired geometric shape will be accurate and smooth.

So that the bending item does not jump from the template (PUNSON), it is desirable to make a semicircular recess, over the perimeter of its rounded part, processing the end of the rashpil shape.

The fixation of the pipe on the template can be done in a different way, stinging on top of it a rounded piece of plywood, which should be beyond its edge within 6-10 mm. True, this option is well suited if the tube has thin walls, since for bending parts with thick walls you need more powerful efforts, while the wooden punch can simply collapse.

Before proceeding with the bending of the pipe, it is recommended to float dry sand into it and shut both ends with wooden plugs.

This will help to avoid the appearance on the workpiece of waves (corrugations) from the inside of the curved section, and a large stretching of the metal on the outer wall of the bend.

Of all the existing pipe bending machines, the widest distribution has received the manufactured pipe-bearing with their own hands, the work of which is carried out on the principle of rolling fixture. Such a production model practically does not have drawbacks, it has little weight and sizes, it can be freely tolerated and takes little space when stored.

Products from polymers are increasingly included in our everyday life. They are able to fully replace other building materials, which for ten years ago there was simply no competition. Plastic water supply and sewage will not surprise anyone. The construction of new wells and wells, restoration and repair of old wells also do not cost without modern polymers. Plastic pipes for drinking water well gradually displacing concrete rings familiar to us or metal. At the same time, they are ahead of generally accepted building materials in many respects.

Polymer pipelines may have different diameters, so that they can be used to create water wells and wells for various purposes. Usually, low-diameter pipelines are used for wells, from 2.5 to 15 cm. For the manufacture of wells, pipe diameters can be 60-200 cm.

Scope:

- viewing wells intended for the prevention and repair of water pipes with a length of more than 12 m;

- turning communications installed in places where the direction of flow direction of the working medium occurs;

- Overflowing wells, providing maintenance and control over pipelines with changes in their diameters.

Advantages of plastic pipes for wells

For the manufacture of casing tubes, a non-controlled polyvinyl chloride is used, which has a sufficient degree of rigidity. This allows it to withstand mechanical loads and temperature differences.
PVC pipes are resistant to UV radiation.
If polyethylene pipes are used (PND), their resistance to negative temperatures is well known.
The smoothness of the inner walls does not leave the bacterium chances to fix them. Such a well always remains clean and neat.
The polymer does not absorb moisture, unlike concrete. In addition, the polyvinyl chloride well does not have seams through which water can penetrate.
Plastic is not a conductor of static electricity.
The corrosion resistance of plastic guarantees material from destruction and provides it for a long service life. For this parameter, plastic is not inferior to the durability of asbestos-cement and thick-walled steel pipes.
Plastic from which pipelines are made are safe for humans. It can be used for drinking water. The material does not highlight outsiders when contacting air or with water.
Plastic is lightweight material, which allows you to work with this type of product without the use of loading equipment. Even plastic pipes of a large diameter for a well can be installed independently.
Plastic seamless well does not need to be careful.
There is a significant savings, because concrete rings, steel or asbestos-cement products have a very high cost.

Materials for the manufacture of pipes

Pipes for plastic well are made mainly from such materials:

Polyvinyl chloride (PVC) / non-controlled polyvinyl chloride (NFCH). Material has a low linear expansion coefficient when heated, keeping its shape perfectly.
Low Pressure Polyethylene (PND). This is a popular material for outdoor use, as they retain their quality even at a temperature of -20 degrees.

How to make an ordinary well

You can make a well made of plastic pipe with your own hands. To do this, it is necessary to decide on the place of the future well and purchase the pipe of the desired length. The diameter of the pipe can be from 40 cm or more.

Sequence of performance:

Manually or with a wide beara, a mine of a certain depth is digging. It should achieve aquifer.
A plastic pipe for the well is prepared. On the bottom, at a distance of 50 cm, drill a plurality of holes, using the drill with a diameter of 7-8 mm. Holes drill in the flap of the outer shell.
Wake up two layers of geotextile (you can use a special polymer) perforated bottom of the pipe, fixing the material with the wire. This is necessary to filter water.
Lower the pipe in the mine so that it reaches her bottom.
The gap between the walls of the shaft and the tube plump sand.
The top of the pipe towering above the surface of the soil will insulate the polystyrene foam.
Drop into the well of the submersible pump and proceed to the swinging of the well. This action is performed until the exit of clean water appears.
Install the lid on the well.

In the photo example of a finished well made of plastic pipes

How to make an Abyssinian well

Abyssinian Well suggests the pipe to the soil until the aquifer is achieved. The appearance of polymeric materials made it possible to use them for the manufacture of such structures. Abyssinian well from plastic pipes is made easily, and serves a long time. To do this, use a pipe with a diameter of 1-1.5 inches, at the bottom of which holes are drilled.

Important: Locking plastic pipes is fraught with damage, therefore the method of soil drilling is used.

The procedure for the manufacture of the Abyssinian Well with their own plastic pipes:

Using a hacksaw or a drill perforation of the bottom of the pipe.
Next to the perforated part of the pipe, you must install a grid-filter from a stainless steel. It is necessary to consolidate it by the method of fifty.
At the place of the future well, a hole of about 1 cube is digging. Her center begins drilling well. If there is no special equipment, you can make drilling with a conventional garden bora, which allows you to increase the length of the rod.
When the bee reaches the aquifer, the prepared plastic tube is lowered into the well. Pipe pieces are increasing through a threaded connection.
The pump nozzle is lowered into the pipe, with which the well is pumped before the appearance of pure water.
The place around the pipe is recommended to fill with concrete to protect the well from wastewater.

has a limitation of the depth of the aquifer. When it is located at a depth of more than 8 m, the construction of the well-needle will be problematic.

Repair of an old well with the help of plastic pipes

In addition to the construction of new wells, the polymer pipes make it possible to repair old wells, in which water has ceased to flow, or their concrete rings have shifted and began to pass water. A plastic sleeve is inserted inside the old well, and the bottom of the well deepens. The filter material is covered between the plastic pipe and concrete walls. It can be coarse sand, sandbetone, small crushed stone. This material will serve as an additional filter, and water will come inside the plastic sleeves only through the bottom.

Using plastic pipes, it is possible to improve the efficiency of the existing well, as well as make a new well or well.