We make a glowing table with your own hands: the advantages of creating. Glowing table with your own hands, photos and video Features of assembly countertops made of pine board

Glowing in the dark, the tabletop is not only original, but also practical. Especially if the table is installed with it in the garden, in a gazebo or near the window. The light effect created by a luminescent coating can last up to 12 hours.

In this article, we will not fully describe the process of manufacturing the table itself, and focus only on how to make a luminescent countertop (luminous). The process of manufacturing a luminous coating is extremely simple, but in this case there are some points that should be considered in advance.

Materials and tools

From the materials you will need a countertop itself (in our case, cypress boards were used, which had congenital flaws in the form of resin chambers), as well as transparent epoxy resin and organic fluorescent powder. So that you do not look for it on shopping, let's give a link to a very quality option with free shipping. This powder can maintain a glow from 7 to 12 hours and serve faithfully for 7-10 years.

We will also need paint tape and disposable cups. In addition, the surface at the final stage will need to be covered with varnish.

From the tools: semicircular chisels, grinders (or skin), knife and a couple of brushes.

Preparation

In our case, the preparation process was cleaning the natural resin chambers of cypress from the residues of the dried resin. To do this, we used a conventional screwdriver and blowing. But if you use the ready-made worktop, you will have to cut the cameras on your own using semicircular chisels. We would recommend the depth of cutting from one to one and a half centimeters. In this case, there will be more luminescent composition in the resulting hopes, and, therefore, the glow will be brighter and long.

Cypress has enough deep cameras, which in some places form through holes in the 25-millimeter boards.

Of course, the surface must be sanded, after which the acrylic plates should be fixed on the ends so that the imposed luminescent composition does not flow. The table top at the edges can also be saved by painting scotch.

To prepare a luminescent composition, it is necessary to mix the components of the epoxy resin in one-time dishes. It is most convenient to use 200 gram paper cups, but you can take half-liter. We poured half a cup of resin and separately half acknowledged hardener. In each of them, powder was added and stirred.

After connecting two components of the resin in one glass, you have about 5-7 minutes to fill in the resulting composition made and treated on the tabletop of the hollow. We have 100 cm in size with deep hinders (which you can see above in the photo) left two liters of epoxy resin and 100 grams of fluorescent powder. It is better not to save and pour more, so that the glow was bright.

Now everything is ready to apply a luminescent composition.

Application

The resulting composition should be accurately poured on the chosen-made slots and hopes. It is important to note that the epoxy will be absorbed into the tree, because you will have to put at least a second layer.

The whole process took about an hour. After that, we walked around about 12 hours, allowing epoxid to harden.

Further work consisted of trimming the edges of the countertop to get rid of the irregularities and sunsteps of the resin, as well as in grinding. In order to achieve a point effect, we had a grinder to remove a sufficiently large layer of the surface, where the epoxy was hit outside the hollow.

Final stage - processing of edges and surface coating with two layers of varnish.

May the light be! Always and everywhere! Transparent, white, blue. Let us light our way to miracle. Let it hesitate our peace. Light road path holding, bright them thoughts, dreams. Yes, there will be a light, good qualitative, which is looking for light of purity.

And here is the light: soft, mysterious, calm, evening. Reminds me a night cricket in the bushes of fragrant raspberry, stringing about peaceful, kind, eternal and illuminating his appeal with gentle flicker. So that it is not only audible, but also it can be seen that everything will be fine! Well, all, of course, aware of what the creativity is the most the best way Come to the good and enjoyable way! This incredible countertop is done very simply due to modern materials. Of course, for working surface kitchen table optimal option - This is a tabletop from natural stoneHere you can choose for yourself the optimal option. Chose, installed, they prepared to eat - now you can relax, taste a pleasant food for a luminous table.

This is a bolt cypress board with very noticeable cracks, which beat the author of this work. Unfortunately, I did not find the original source, as a lot of recesses. If someone knows, I will be glad to the prompt and, of course, I will point the master.

From the pictures it is clear that the master prepares the selected board, shelves its orbital grinding. And then covers it with a special mixture.

This is a mixture of epoxy resin and fluorescent paint based on phosphor, which, by the way, are different colors And they are able to work wonders. It must be pouring into cracks, so many times so that the solution completely filled them. The tree absorbs the liquid, so you need to wait, when but already goes out and stops absorbing the substance shining in the evening.

Video for clarity. Creative success!

He who wants to make an apartment interior original or add "highlight" to equipment cottage plotThis is suitable such an option - a table with "backlight". A product is created using epoxy resin and two types of resistant paints. All work - from grinding to cladding - a newcomer is quite available in the joinery.

All work - from grinding to cladding - a newcomer is quite available in the joinery.

Furniture with luminescent effect looks unusually and especially interesting.

The manufacture of the glowing table does not require special material and labor costs. Process wooden countertop with help special resin Anyone who knows how to keep the instrument in their hands.

When decorating the table, you can come up with your design, based on the quality and texture of the material.

Furniture with luminescent effect looks unusually and especially interesting.

Such products you are unlikely to see in a free sale, usually they are fulfilled to order and cost them quite expensive as handmade. Thick boards or ready-made wooden table With an interesting texture. Applying epoxy resin - the case is half an hour. After a while, with the correctness of the observance of all steps of processing, you will get a table with a fascinating luminous effect.

Independent creation of furniture for giving or house is a great help for budget saving.

Determine with design and design

When processing, the design of furniture design does not matter. To create a luminous effect, use only a worktop, although you can make furniture completely with a luminescent surface. Designers converge in the opinion that it is better to treat individual panels - so the product looks more interesting.

A glowing table can be made stationary or folding.

The manufacture of the glowing table does not require special material and labor costs.

Depending on the texture, you can apply part of the resin - on cracks, or to cover with luminescent composition (with a light blue or other tint) the entire worktop, including the edges. Choose a "motley" option or relatively smoothly glowing must be based on your taste and needs.

Designers converge in the opinion that it is better to treat individual panels - so the product looks more interesting.

Necessary materials

For the manufacture of glowing tables, such materials will be needed:

boards - 2 pieces (40-50 cm wide, 1-1.2 m long);
epoxy resin;
adhesive paper;
luminescent and transparent polyurethane paint;
sandpaper.

Choose a "motley" option or relatively smoothly glowing must be based on your taste and needs.

Treat the wooden countertop with a special resin is capable of anyone who can keep the tool in their hands.

Tree is chosen with noticeable cracks incorrect form. The board with visible places from the cutting of a bitches and an inhomogeneous texture is welcome. Well suited for cypress or oak. If the tree is not dry enough, put it for a while in the sun.

The tree is chosen with noticeable cracks of the wrong shape.

Epoxy resin must be taken so much to have enough cracks several times.

Independent creation of furniture for giving or house is a great help for budget saving.

Required tools

For finishing furniture will be required:

sander;
lobzik.

The table is polished as before surface coating epoxy resinand after

The table is polished both before the surface coating with epoxy resin and after.

Before treating the surface, the tabletop should be collected from two prepared boards.

After a while, with the correctness of the observance of all steps of processing, you will get a table with a fascinating luminous effect.

Production Process: Step-by-step instruction

Before treating the surface, the tabletop should be collected from two prepared boards. By connecting them, pass the base.
On the table, pour the prepared mixture of epoxy resin and fluorescent paint. The composition should fill all cracks, so repeat the procedure 8-10 times. After that, close the surface with adhesive paper and leave to dry until the next day.
The finished surface after removing the paper is polished. After stripping, cover the basis of polyurethane paint.
Once again grinding machine By another wet surface. Remove the residues of the resin. If necessary, the edge can be cleaned, and the corners are rounded with a jigsaw.

The table with a luminous surface can be made to your liking

Finishing Stage - Decoration

The table with a luminous surface can be made to your liking. Thick wooden plank Looks great like in simple sight (Even with visible "defects"), and in combination with carved legs. This can be done by applying the jigsaw. You can cover them with varnish or use the remnants of the epoxy resin, as well as the worktop to give a single style style.

You can cover lacquer or use the residues of epoxy resin, as well as the worktop to give a single style style.

A glowing table can be made stationary or folding.

After processing, you must pass the furniture with the type of machine.

In the dark, the product will be glowing in inhomogeneous divorces, which creates a "magic", the festive effect that in itself is a decor.

In the dark, the product will be glowing in inhomogeneous divorces, which creates a "magical" effect.

Depending on the texture, you can apply a part of the resin - to cracks, or to cover with a luminescent composition.

If the contrast is desired, the support is covered with paint, differing in color from the main palette.

Creating a festive effect that in itself is a decor.

Well suited for cypress or oak.

Video: Glowing table with your own hands

50 photo ideas: glowing table with your own hands

From the presented master class, you will learn how to make yourself glowing tablewhich B. furniture stores There are considerable money, and thanks to this information you will make it just for the very dick. Today, the manufacture of furniture is becoming more fashionable, as well as various interior sings, that is, people are looking for uniqueness in things that surround them, someone needs it for self-realization and acquire self-confidence, and someone just loves to do this .

And so to make a tipped table, you will need old and cored boards. It is the old and drunk, worms and other bugs that are so necessary in order to fill these cavities with a special luminous solution. Now let's get acquainted in detail and look at everything that it took the author.

Materials

board (old and backed)
epoxy resin
metal legs
metal plate 2 pcs
carbon black
nut
bolts.

Instruments

electropolitanzik
drill
brush
clamp
rule
screwdriver
capacity for mixing components

The process of creating a luminous table.

And since it was already mentioned above, the author took the old and dull boards accedened by pests, it is clear that he did not buy them in the construction market. emery paper. Then the author picked up and saw the boards needed to the size of him, so that they become the same size.
The resulting accessories should then be connected to a single worktop, this action is done as follows, it zooms the side parts of the boards with carpentry glue, and then stole them with clamps and left to dry.
Then after the countertop is dry and will be ready, it should be blown out compressed air, namely, all the slits and wormworms that there are no duchi and possible pests.
After you go through the surface with emery paper, you need to do everything extremely gently, because the board is very gentle. And so the surface of the table top is prepared and the time of preparation of a luminous solution and filling to the cavities of the table.

Preparation of the solution: This will require epoxy resin, hardener and powder Luminofora , He will be glowing. The proportions of the mixture each selects itself, the glow can be checked as follows, give a bright flash to the mixture and turning off the light see how the solution will be lit. Further, the author fills the cavity, pre-laying a wax paper under the table top, because the moves can be through.
After conducting this operation, the master left the countertop for drying. And then processed the edge of the table manual milling.
Due to the fact that the board is rather weak in relation to density and integrity, the author on the back of the countertop scums these such naiks.
Looms glue metal plate And sticks.
And so so it is screwed legs to the table. Well, here's the actual table is ready.
Such a table will fit into any even the most exquisite and expensive interior, and the cost of this table is absolutely keenly, but in stores such tables are about $ 1000. Imagine 😉 So take this material to note, and so as not to lose touch with us and our site Join us in the group

We all know well that chashles, termites, cores and other "lovers" of wooden food are one of the main shredders of roofs, furniture, wooden floors etc.

If you find the right approach to spoiled material and handle it a bit, you can get a great original glowing table, which, for example, on some sites costs about 780-800 dollars. Therefore, proceed.

1. To make such a table, try to choose the boards, the most damaged by the cores. But, most importantly, do not forget to treat all the material with chemical or heat treatment. Otherwise, the bug will not stop, and will continue to make their ricking matter. Fig.1

2. After that, overtake the board from all sides. And then cut the pieces. Which will be equal to the length of the table. Fig. 2.

3. If you want to get a wide countertop, you will have to smack several boards together. This procedure is performed using joinery and spikes. The glue must be applied necessarily along the entire length of the board. After you do it, pull the boards with clamps and let them dry. Fig. 3.

4. All the moves along which the treasures moved, it is necessary to be treated with the removal of pipes and rot (for this it is recommended to simply blow with compressed air). Fig. four

5. Next, you must pass the surface of the table top to such a state so that it is smooth and smooth.
6. The next stage is the preparation of table tops to the pouring epoxy resin. Must under the lower side of the table top it is necessary to put the wax paper, and on the sides, make a special side of the plexiglass. This procedure is required, since bugs can make end-to-end moves.

7. Next, you need to prepare a resin for fill. To do this, we have a certain amount of resin and hardener. The epoxy resin needs to add phosphor powder (it is it that provides a glow in the dark). As for the very number of phosphor, there are no certain proportions here. You need to say so to guess. After you have already mixed the resin and phosphor, you need to impact an outbreak on the resin, and then in the dark room to look at the luminescence density itself. If you like it and is suitable - add a hardener. Fig. five

8. Now we pour all the holes with epoxy resin. It will not be spread over the table because of its viscosity, so it is recommended to dissolve it immediately after the fill.

9. After the resin hardens, in any case, irregularities will remain on the surface. To do this, simply get raised all the defects. Initially, use the coarse sandpaper, and then go to fine grain (somewhere from 80 to 400).
10. The edge of the table is best treated with a manual milling. Fig. 6.

11. Well, the most responsible moment is finish finish Your table. Tabletop open lacquer, and when it dries - polish the shallow emery paper (grain 1200). This procedure must be carried out a couple of times so that the table is well glistened.

12. Due to the fact that the tree was used by a manifold, drunk so that the legs were securely secured, we use sheet Material. For this you need from back side Table tops drill special holes for nuts, then apply glue on the plates and stick to the tabletop. Fig. 7.

13. The legs are best use to use metal welds, and to fasten them to use bolts. Fig. eight

That's all. Your table is ready. But know that it will be lit only in the evening or at night. Fig. nine