Remove overtaking saw partner 350. How to properly configure the carburetor on the Partner chainsaw. Adjusting the carburetor chainsaw Partner P350S. Assessment of the state of the cylinder-piston group

Among huge selection Models on the modern building market highlighted a chainsaw partner 350, which is produced by the subsidiary of Huskvarna.

General view Chainsaws Partner 350

Simple and easy to operate, reliable and unpretentious this saw gained wide popularity among dachens and owners. country houses. Sawing of firewood, trimming trees and bombs - this is not the entire list of work with which this model will cope without problems. Despite the well-thought-out design and layout of the units, with a strength of the power unit, the elements of the transmission and the fuel system occurs.

Experienced rollers know that competent and precise definition The character of the breakdown is half of the work done. Based on a long-term experience of repairing chainsaws Partner 350, specialists have developed a special technique for diagnosing problems.

Main breakdowns Chainsaw Partner 350

It costs it from the simplest knots and mechanisms, ending with more complex.

This allows you to significantly save time and get away from unnecessary operations. Finding a fault is recommended in the following order:

Checking spark chainsaws;
Ignition coil;
Diagnostics of the fuel supply system;
Inspection of crankshaft bearings.

Check sparks on candle electrodes

To diagnose the presence of sparks, you must remove the candle and without removing the high-voltage cable to make several starter jerks. If there is a discharge, you will need to set the gap between the central and side electrode. Its value in the Partner 350 should not be beyond from 0.7 to 1.2 mm.

Candle Candle Control Adjustment

The unkind of this distance can lead to incomplete combustion of the fuel mixture and, as a result, increased fuel consumption with limited power of the unit. As a result of the exceedment of this parameters, the impermanence of the appearance of sparks and interruptions in the operation of the internal combustion engine is observed.

In the absence of sparks on the electrodes, it is necessary to replace the candle and repeat the diagnostic manipulation described above.

If there is also no discharge on a removable candle, it is necessary to check the integrity of the high-voltage wire and, if necessary, replace it.

Diagnostics and ignition setting Partner 350

The absence of a bright blue spark in the candle may indicate the need to inspect the ignition module and adjustment of the gap. For these purposes, remove the plastic protective casing from the saw and check the condition of the coil. The wires leading to it should be firmly fixed with screws should not hang on the connection site. There should be no moisture on the flywheel of the lead shaft, since it interferes with the emergence of an electromagnetic field.

Flywheel and ignition module Chainsaws PARTNER 350

In the absence of such inconsistencies, it is necessary to make sure that the gap is correct between the module and the flywheel. Its value should be no more than 0.2 mm, and therefore, when incurred with the recommended distance, it is necessary to independently adjust the ignition of the chainsaw partner 350.

For the most accurate adjustment, we need a regular coin-shaped or flat probe, which can be used in specialized or automotive stores.

After checking the ignition, go to the diagnosis of the fuel supply system.

An important impact on the correct operation of the saw plays a fuel system consisting of gas tanks, nozzles and carburetor.

Carburetor Partner 350 in the analysis

In case of income, the mixture of the tank is required to inspect the built-in filter and the sapun (hole in the lid). When clogged the fuel filter, it will be necessary to replace it. You can use a conventional sharp needle to clean the sapuna, carefully removing the remains of dirt and sawdust from the valve. When clogged, the carburetor will need to dismantle and careful cleaning.

It must be remembered that the carburetor chainsaw partner is a complex node consisting of a plurality of small parts. Therefore, when dismantling, cleaning and assembling is required to take maximum attention.

The principle of operation of the carburetor

The carburetor serves to mix the fuel mixture (oil and gasoline) with air. His work begins from the moment the barber of the starter saw, which forces the membrane to pump fuel. After a diaphragm controlled, the needle valve supplies gasoline to the main chamber through which it enters the cylinder. By the throttle, you can "enrich" or "delete" the fuel mixture with air. When it is closed, less air will flow into the cylinder at the same level of fuel. In this case, the consumption will be increased with the drop in the engine power. Therefore, the adjustment of the chainsaw partner 350 plays an important role in creating an optimal ratio of moderate fuel consumption at high tool performance.

Setting up carburetor partner 350 with your own hands

Before starting the adjustment work, it is necessary to clean the main fuel assembly from dust and dirt. To do this, you can use compressor with compressed air or a joinery brush-absolution.

To configure the carburetor there are holes on the left side of the power unit, however, for the convenience of determining their position, the specialists recommend dismantling the protective plastic casing. At first, before stopped clockwise, we twist the screws and the quality of the fuel, weakening them after 1/5 ... ¼ turn.

Carburetor Chainsaws Partner 350 with screws settings

With a dismantled lid, it is necessary to know that the quality of the fuel mixture is on the right and, accordingly, the screw adjustment screw is located on the left. For convenience on the carburetor housing under bolts, marking is applied:

- "L" - screw of the amount of fuel (adjustment on low revs);

- "H" - a screw of the amount of the mixture (setting up at maximum revolutions);

- "T" - Bolt Settings idle move.

It is necessary to remember that the adjustment of the carburetor chainsaw partner 350 should be carried out on a heated engine. At high temperatures, the metal is linearly expanding, resulting in bandwidth Channels increases.

As soon as the cylinder becomes a warm screw "L" until the engine will not give the maximum turnover of the crankshaft. After tightening it to a quarter of turnover. It should be noted that in this position, the screw of the amount of the mixture must support the operation of the motor on idling. If this setting is not enough, then we boldly unscrew the "T" bolt to stable engine operation. With the help of the "H" screw, we adjust the work of the chainsaw partner at maximum turnover.

Diagnosis of crankshaft bearings

An important factor at the correct operation of the engine is played by bearings and seals of the crankshaft.

Crankshaft partner 350 with bearings

To diagnose their wear, it is necessary to shake in the vertical and horizontal plane, the flywheel installed on the shaft. If there is an explicit backlash, it is necessary to replace rolling bearings. If there are oily traces on the crankcase, then the glands will be replaced. It will not be superfluous to check the record of the crankshaft partner 350, for which we remove the cylinder and the piston. With the help of the hands, we are tenting it left and right, thereby imitating a natural movement.

Output

Despite some difficulties in repairing chainsaws Partner 350 with their own hands, the owners of these aggregates before passing the tool to specialized centers try to restore performance on their own. After all, most problems can be eliminated by conventional plumbing tools and with the presence of basic experience in repairing mechanical nodes.

Chainsaw PARTNER 350. Frequent breakdowns, carburetor adjustment Was Last Modified: September 15th, 2017 by Administrator

Home »Blog» Repair Chainsaw Partner do it yourself To bookmarks

Repair chainsaw partner do it yourself

Repair saw partner - The question that torments many owners of this saw, who want to repair it with their own hands. On this page you can download a saw repair manual in PDF format, as well as a scheduling scheme Partner 350, 351, 352, 371.

Repair Chainsaw Partner Photo 1

Repair Chainsaws Partner Photo 2

In order to facilitate the search for information on independent repair Chainsaw, we publish not only instructions for you, but also a video that you can see directly on our site.

Repair Chainsaw Partner Photo 3

Repair information:

Video Repair Chainsaws Partner 350, 351, 352, 371

You can read all the articles in the content. Be sure to subscribe to our twitter @ orlova4ka. In the support of our site, share our articles "Repair Chainsaw Partner with your own hands" with your friends on social networks.

Chainsaws Partner 350: Causes of breakdowns, repair with your own hands

Chancellitations Chainsaw Partner 350

This model enjoys considerable demand from consumers, but it most often buying subsidiaries for work in their sites. Use the saw not only for wood harvesting, but also in construction.

In general, chainsaws partner 350 are characterized by its compact sizes. They are sufficient enough powerful engine. Their main advantages - light launch I. reliable work . performed at the expense of a qualitatively made electronic system Ignition and fuel pump.

Use such a chainsaw is completely safe. In her embedded protective systemwhich automatically performs launch of inertial brakes For chain. In the same mode, its lubricant is carried out.

With the launch of the chainsaw partner of the problems will not arise even in winter because it has fuel primer. The starter drum is equipped with an impeller helps to cleanse dirt. In addition, manufacturers have provided the CCS system tool. Such a design is delayed by residual particles, and is also used with a debt air filter.

Developers to increase the life of chainsaws on the cylinder of the piston group made chrome walls. This model has an ergonomic shape handle and system against vibrations .

What might have breakdowns

Faults Chainsaws can be divided into groups:

Violations in the operation of the motor (ignition, exhaust and cylindro-piston system, fuel supply).
The failure of such nodes as a coupling, a chain brake, a lubricant or bus system.

Breakdown by the engine chainsaw Meets more often. The most time is spent on its detection and repair. As a rule, it boils down to such manifestations when the engine works unstable or stalls at all, the motor will not start, does not develop power.

Before you start repairing chainsaws, first check all possible reasons Violations in its functioning, and even better watch the video. The benefit today on the Internet you can find any material of interest.

Then you have to prepare required tools For repair damage:

the device diagram (must be included in the delivery);
keys, including for spark plugs.

Fault of the ignition system

When the engine refuses to work, but at the same time there is a spark on the candle, and the fuel comes check ignition .

It is not difficult to check it at all: unscrew the candle, and adjust the clearance between the contacts, connect it to the wire and press it with the cylinder body. After that, follow the spark.

If any deviations occur, you need to perform setting up the ignition system. In general, this process is similar to ignition adjustment in other two-stroke engines.

The problem of feeding fuel

Install such a malfunction of chainsaws will turn out when inspection of the candle. The cylinder may not be fuel for different reasons:

The fuel filter installed in the tank is very clogged.
The hole in the tank cover was hampered, which prevents gasoline leakage.
From the carburetor badly or does not come fuel at all.

In the event that there is no proper relationship between gasoline and air mixing in the carburetor, or not enough fuel, check whether the channels and the carburetor air filter are not clogged. In addition, it may be needed to adjust.

The filter before cleaning is neatly removed and washed with detergent. After that, it is left to dry. Then put in place.

Carburetor adjustment It is usually screws - maximum and minimum revolutions. When it is necessary to strictly follow the instructions for repairing chainsaws, otherwise you can spoil the motor. Sometimes manufacturers leave only one adjustment screw to eliminate the intervention of inexperienced masters in the work of the carburetor.

If the debugging has not corrected anything, then it is worth producing cleaning channels and filter mesh. And still check the integrity of the membrane.

Do not forget that the carburetor is one of the complex chainsaw mechanisms, so it is necessary to approach its cleaning and disassembly.

It consists of a variety of small elements that may imperibly jump out and find them difficult. Often after disassembling this device, some users cannot collect it.

What to do if the muffler clogged

If the engine chainsaw functions normally on small revolutions, but at high smoke and stalls, then the reason is likely to be in the silencer. First dismantle it, but do not forget to close the outlet.

Then disassemble I. clean from Nagara With a dry way or detergent, dried with a hairdryer, assemble and perform installation.

Do not carry dry cleaning without special Tools Protection, since carcinogens in naigar are highlighted in the form of dust. Inhaling it is very dangerous. When operating chainsaws, it is necessary to monitor the quality of the fuel mixture.

Breakdown chain

Need to regularly lubricate chain During the work of the saw, because it works in extremely hard conditions. The abrasive particles, dust and even overheating negatively affect its service life.

If you leave a chain in a dry condition, it will soon happen to pulling and overheating. In the worst case, the jam can happen, that is, a breakdown of the stars. The oil according to it is served through the channels that are quite often clogged with sawdust. They must also be regularly cleaned.

In addition, constantly clean under the lid chainsaws From garbage and sawdust, because due to this may not work the chain brake. In addition, pollution has a bad impact on the performance of the device.

The failure of the cylindro-piston group

The most serious faults are scratching on the surface of the piston and cylinder, their damage, the evinacle of the piston rings in the grooves, breakdown the crankshaft bearings.

Most of them lead to the impossibility of starting the engine, since pressure drops in the cylinder. There are several options for repair and checking the state of the cylinder-piston group (CPG).

For example, you can in the engine to measure compression. This operation uses a compressometer that is mounted in a candle hole. Thus, you can check the status of the parts of the CPG.

To watch the side surface of the cylinder, it is necessary to remove the muffler And look into the open gap. Although the review is limited, general state CPG can be seen.

To accurately assess the performance of the cylinder-piston group will have fully disassemble the engine Chainsaws. First, it is disconnected from the cylinder Carter, after which the piston is pulled out. If there are chips, jackets and large scratches on it, then it must be changed.

Low compression It occurs most often when they are cheering and damageing the piston ring. Be sure to check that it was absent Nagar. In addition to it should sit free In the piston groove and be pressed to the surface of the cylinder.

Generally, you always need follow the cleanness of chainsaws and different holes. Only it will be possible to avoid many breakdowns and further repairs. Be sure to watch the video, how to do it right.

Repair chainsaw "Partner 350" with their own hands. Malfunctions and ways to eliminate them

Saw "Partner 350" has decent power and is very convenient to use. However, the flywheel in this model is not designed for long work. If the motor overheats, various breakdowns may occur. In order to independently make repairs, you need to know the device chainsaw "Partner 350".

Starter malfunctions

Starter often fails. In this case, the repair of chainsaws "Partner 350" with your own hands should be started with the following: unscrew the side cover, which is located next to the gearbox. The starter at the saw presented is near the engine. In order to inspect this item, the air damper is first removed.

Next, you need to disconnect the carburetor. The starter in this model is connected to the throttle. To split them, you need to use a screwdriver. If the starter is visible to the nagar, this item will have to be completely replaced. In this case, an ordinary modification is established, and it is not difficult to find it in the store. However, the best spare parts on the chainsaw "Partner 350" to acquire in specialized workshops. After replacing the starter, it will only be left to screw the throttle and put the carburetor with the lid.

Flywheel does not work

Flywheels in this saw break quite rarely. Most often, this is due to the overheating of the engine. In this case, the repair of chainsaw "Partner 350" with their own hands should be started with removing the protective cover. After that, the engine is first viewed. In some cases, the tire can overcome. If there are no darkens on it, it means that you can immediately twist the flywheel.

In order for it easier to get it, you must first disconnect the crank. It is directly over the flywheel. To do this, you will need a cruciform screwdriver. After that, the flywheel can be easily unscrewed from the panel. Particularly carefully consider its head. If it is deformed, then the flywheel will have to be replaced. In this case, it is necessary to say the exact diameter of the head in the store.

Repair of the Barabana

The battery breakdown in the saw is accompanied by a loud sound when turned on. In this case, the repair of chainsaws "Partner 350" should be started primarily from the inspection of the fuel system. The problem can be in the carburetor breakdown. In some cases, the drum flies due to a crank, which comes out of the grooves. In order to inspect it, you need to open the protective cover. Next, the throttle is removed and the fuel system is checked.

All tubes must be connected. After that, it is necessary to inspect the crank, which is above the carburetor. If he flew out of the grooves, it can be installed independently. However, if it is strongly deformed, it will have to be replaced. The drum in this saw is located near the air damper. When he beats about the coupling, his protective ring is damaged. If it is completely overcome, it means that the drum will have to be completely changed. In this case, you need to know the product labeling. In the installation, the drum is pretty simple, and you can cope with installation yourself. In this case, it is important not to damage the fuel system when repaired.

Replacing the connecting rod mechanism

The connecting rod mechanism is quite complex has a chainsaw "Partner 350". Its malfunction is often accompanied by loud operation of the motor. It should also be noted that when the connecting rod mechanism fails, the carburetor often comes out. In this case, the repair of chainsaws "Partner 350" with its own hands to start with inspection of the ignition module. It will also be necessary to fully check the coupling. In particular, the state of centrifugal clutch deserves attention.

In order to examine it, it is necessary to remove the top cover. Immediately the coupling for this model is located near the carburetor. To get to the centrifugal clutch in a saw, the flywheel is removed. Next, the carburetor head is disconnected. In this case, it is important not to damage the fuel system. The centrifugal grip on the bolts is attached. You can disconnect this detail using the key. If there are cracks under the cylinder, it means that the grip will have to be changed. However, some experts advise not to rush. If the cracks are shallow, you can try a little strain the surface with a file.

Sanding Sapuna

Sapun in the presented model clogs when low-quality fuel is used. In such a situation, the repair of piston chainsaw "Partner 350" must be started with the inspection of the carburetor. In order to see it, you will have to remove the top cover of the device. Next twists the ignition module. After that, it is important to disconnect the crank immediately. In this case, you will have to use keys. The next step is disconnected by the drum.

Immediately behind it is the carburetor. You do not need to remove it for inspection. First of all, the throttle is checked. In some cases, the problem may be in it. If the throttle is fine, you need to look at the bus. When it is damaged, the sides are a little shot down. Cracks can also be observed in the central part of the tire. If the item is deformed, it will have to be replaced. Spare parts for chainsaw "Partner 350" to acquire better in specialized workshops. On your own tire on the carburetor is quite difficult. In such a situation it is more expedient to contact a specialist.

Cleaning carburetor

The fuel is very demanding chainsaw "Partner 350". The repair of the carburetor is produced when its nozzles are contaminated. In this case, all internal mechanisms should be inspecting. When fuel leak occurs, they should be trail. If everything is in order with the hoses, you need to inspect the carburetor directly. To do this, the cylinder is first removed. This is further important to remove the crank, which is located next to the coupling.

After that, it will be possible to look at the carburetor. It consists of the lower unit, as well as the top with the ignition system. To unscrew the item, you have to use keys. After disconnecting the carburetor, it is necessary to view its base. If it is not deformed, then the problem is in the ignition system. In particular, they can face contacts. Separately, they, unfortunately, are not replaced. In this case, you will have to buy a new carburetor. Install it will be quite simple.

Chain problems

To control the chain, a special trap is applied, which has a chainsaw "Partner 350". Type faults are a consequence of improper operation of the device. As a result, the chain can be saved after a while. In such a situation, the saw repair should be started with an inspection of an aspect. It is located near the handle. It is not necessary to shoot it in this case. If the cloves of the asterisks are not deformed, you can simply try to lubricate them with machine oil.

Then it is important to inspect the trap. In the device it is quite simple and is a set of rollers. When the trap fails, they are knocked out from the chain. It is impossible to correct them yourself. The only option is to put a new trap. To do this, a screwdriver is used. Locking it is carried out on three nuts. When installing a trap, it should be noted that the rollers are located at the top and must be near the chain.

Repair choke

If the chainsaw "Partner 350" does not start, perhaps the problem lies in the throttle. In this model, it connects directly with the coupling. When it turns out a large load on the engine, it does not withstand and burst. In such a situation, the saw repair should be started with the inspection of the coupling. In order to get to it, you will need to unscrew the protective cover of the model. Next will only have to remove the crank.

After that, it will be possible to explore the coupling and choke. In some cases, it flies out of the clamp. In such a situation, nothing needs to buy. However, if a gap occurred, then a new throttle will be required to repair the saw. In order to install it, it is important first to unscrew the clamp. It is fixed with just one bolt.

9 of the famous women who fell in love with the manifestation of interest not to the opposite sex is not something unusual. You are unlikely to be surprised or shaking someone if you find yourself.

13 signs that you have the most best husband Husbands are truly great people. What a pity that good spouses do not grow on the trees. If your second half makes these 13 things, then you can with.

What is the form of the nose can say about your personality? Many experts believe that, looking at the nose, you can say a lot about the personality of man. Therefore, at the first meeting, pay attention to the nose is unfamiliar.

7 parts of the body that should not touch your hands. Think about your body, as about the temple: You can use it, but there are some sacred places that cannot be touched by your hands. Studies show.

15 Cancer Symptoms, which women most often ignore many signs of cancer similar to the symptoms of other diseases or states, so they are often ignored. Pay attention to your body. If you are noticeable.

What is the virgin in 30 years? What is interesting, women who did not have sex practically until the middle age achieve.

Chainsaw partner 350: do-it-yourself repair, video

Today, almost every household there is a chainsaw, which is a worthy substitute for axes and manual Pilam. The ideal solution For people living in a private house, or construction, will be manual benzaw "Partner 350". This tool of the Swedish manufacturer is very convenient and compact, so suitable for any work on the household plot.

However, the improper care and intensive operation of the unit can lead to its breakdown. At the same time, it is not necessary to immediately contact the service workshop. Many faults can be eliminated with their own hands. To do this, it is enough to study the saw device and video instructions for its repair.

Constructive features Chainsaw "Partner 350"

Reliable and easy-to-use saw of this model has a gasoline engine with power of 1300 W. It is easy to launch, which is carried out by the built-in professional fuel pump and electronic ignition system.

Chainsaw is equipped with a protection system that automatically activates the dual inertial chain brake. Chain lubrication also occurs automatically. Change the tension of the circuit of this unit is very easy to use only two keys.

The chainsaw is equipped with a fuel primer, so it is easy to start at any time of the year. The tool starter drum is equipped with a special impeller, with which it is cleared of contaminants.

Filter with CCS system Can delay all residual particles. In addition, such a system allows for a long time to use the air filter, while saving fuel consumption.

Manufacturers of chainsaw "Partner 350" equipped the walls of the cylinder of the piston group by a chromed coating, which significantly increases the service life of the tool.

Main faults Chainsaw "Partner 350"

Most often, the reason for the breakdown of the tool is associated with interruptions in the operation of the engine or other nodes and systems. Demolition is required to eliminate any faults. To do everything correctly, you need to know the structural features of the chainsaws and the main reasons for its breakdown.

Check the ignition system

First of all, with malfunction any chainsaws, you should explore the spark plug. To do this, the wire is first disconnected, and then the candle itself is turned off using a special key. According to her appearance, you can understand the cause of the problem:

To check the performance of the ignition candle, it is necessary to wear the ignition cable, connect the pliers cylinder and the candle nut, and start the starter. If there is no spark. then the candle must be replaced.

Repair of the fuel system Chainsaws

Reasons why fuel-air the mixture does not fall into the cylinder. There may be several:

To diagnose the clogging of the filter or a sapuan, you just need to disconnect the hose and see how fuel flows. Trickle from the tank should pour out good head. If it is intermittent and weak, the filter needs to be pulled out through the tank and rinse or replace or replace, and the breathing is cleaned with a needle.

The carburetor chainsaws is a rather complex device equipped with a variety of small parts. Therefore, its disassembly and repair is better to entrust specialists.

If a carburetor filter is clogged, then it can be carefully removed, shaken, rinse with detergents and put in place.

With your own hands, the carburetor can only be adjusted. This is done three screws strictly according to the instructions.

Cleaning the muffler

In some cases the engine begins to chop And smoke on large turns. At the same time, it works fine on small turns. Most likely the reason is that the silencer is clogged with combustion products.

To eliminate this malfunction, the muffler is removed, disassembled and using detergents cleared from Nagara. After that, it needs to be dried with a hairdryer and install in place.

While the muffler will be removed, the outlet of the saw must be closed with a clean cloth.

Repair of the cylinder-piston group

In this group, malfunctions are quite rare. When a breakdown of any element is most often replaced with a new one.

The main malfunctions of the cylinder-piston group:

The engine power can be lost due to low (about 5 atm) pressure in the cylinder. To measure it, a special pressure gauge is needed, which is called a copressometer. Normal operating pressure of cylinder 8-9 atmospheres.
If hot gases are thrown into the engine crankcase, then the piston rings are most likely.
Pressure loss and gas emissions through slots may indicate the destruction sealing pads Cylinder heads. They must be replaced.

Fully evaluate the status of all elements of this group only visually, through a hole from the filmed silencer. If it is possible, the cylinder head or the entire cylinder is removed.

If the reason for the breakdown chainsaw is insignificant, it does not matter - by Russian, or Chinese manufacturers a tool is made. Disassembly and repair of the unit can be easily made with their own hands, after studying its design and video instructions for troubleshooting.

Chainsaw Partner 350 S - Characteristics, Troubleshooting, Operating Instructions

To enlarge the pictures, click on its thumbnail.

We advise regularly monitor the health of the security group: brakes and chain catcher. Remember that the saw should be thoroughly cleaned from fine chips. It not only can score the technological holes in the oil pump and other places, but also to prevent the brake operation.

Operating Instructions for partner 350

IN this Instruction You will find not only detailed description Saws, but also the main techniques of work with the tool. We want to draw your attention to that this chainsaw can operate on gasoline AI95 or AI92 with the addition of oil for two-stroke engines in the ratio of 1:50.

Carburetor adjustment Chainsaw Partner 350

This is the most frequently performed procedure in the process of maintaining chainsaws performed by the owner independently, so it should be learn. It is similar to the adjustment of the carburetors of most chainsaws and is described in sufficient detail in the proposed video:

It is important to complete it by adjusting the idling screw, providing the fixability of the chain when working in this mode. If the chain does not stop at the lowest stable circulation, this indicates the need to repair the clutch and this saw is unsafe.

Disadvantages of saws

On the russian market You can meet not very high-quality fake chainsaw partner 350, which is not only an additional evidence of its popularity, but also harms the brand as a whole. Yes, and other models of this brand are successful in summer houses and farmers.

If you are ready to consider a partner 350 as your home tool For sawing the latitive trees, cutting bits and other not very voluminous works, then there should be a consumers, more often than others called their owners:

1. Not a very high quality vibration damping system, as a result of which the hands get tired pretty quickly. But, given that this is a household tool that requires 15 - a 20-minute rest every 20 - 25 minutes of work, you can accept this disadvantage.

2. Feeding oil from the lubrication system of the chain, which, however, suffers from the majority of chainsaw, equipped with it, including a more famous relative, chainsaw partner - Huskvarna. (Link)

3. Lack of visual control over the oil level, which is not very convenient in the work, and the operation of the saw without lubrication will result in rapid stretching, overheating and wear of the chain.

Of course, you can with the help of this saw dump a tree with a thickness of up to 30 - 35 centimeters, but its main purpose is to work on the site. Therefore, in conclusion, we offer you the most objective video review of this model:

Dear readers, if you have any questions, ask them using the form below. We will be happy to communicate with you 😉

One of the most popular household chainsaws in Russia is the 350th model of the saw firm partner. This can be explained by a number of advantages of this model.

compactness and low weight with sufficient power;
relatively democratic price;
durability;
great repair base.

Chainsaws Partner - Features

Many sources claim that it was this Swedish firm that released the first serial household chainsaws in Europe. And it happened in 1949.

We are considered to believe that this is good Chinese saws, and partly it is like that, most of the part-selling partner sold in China, which is honestly written on their nameplates. But besides China, the saws of this brand also produce in America, Italy, Norway and England, and they can also be purchased in Russia.

For more than 10 years, this brand has belongs to the Huskvarna concern - one of the leading manufacturers in this segment, which affects not only constructive features Saws, but also on the widest network of service centers, capable of quickly and efficiently serving it.

Few people know, but for the first time the chain brake chainsaw and the heating system of the handles was applied precisely on the chainsaw partner, so they should not be underestimated.

There are about 30 modifications chainsaw of this brand. From the most low-power saw partner 340S from manufactured today, and having 1.44 kW of power at 13,500 rpm, to the most powerful partner 842, with its 1.6 kW at 12 thousand rpm.

But perhaps the 350th model remains the 350th model.

Overview Saw Partner 350

It is her we consider it more.

Specifications:

power 1.52 kW;
working volume 36 cm3;
idle speed 3000 rpm;
maximum recommended speed of rotation 13000 rpm;
silent bus length 40 cm;
step chain 3/8 ".

The use of saw tires with a length of 45 cm is allowed, but for this length drank, nevertheless, weak.

The saw is equipped with a hand brake chain, lIGHT SYSTEM The start, primer for fuel pumping, the carburetor air damper regulator, has chrome walls of the cylinder and the system of air preparation cyclotron. It is collected quite efficiently and, yielding in the class with more eminent classmates from Huskvarna and Stalil, exceeds in its consumer characteristics almost all other chainsaws of the household segment.

Chainsaw Partner 350: faults and their elimination

One of the main features of this saws, users note the durability of operation with a minimum quantity. And yet they occur. To determine why the saw stopped working, you need to make elementary diagnostics.

If the saw does not start, then:

there is no spark on the candle;
fuel is not fuel;
does not do air.

First, check the presence of a spark: twisting the candle by attaching it to a high-voltage wire and putting on a cylinder, pull the starter. If there is a spark, then clean and adjust the gap on the candle (0.5 - 0.65 mm). If it is not, then you need to change: either flywheel or coil (magneto). In addition, the candle itself may fail or interrupt the high-voltage wire.

The next step will be the fuel supply check. To do this, you need to disconnect the feed hose from the carburetor and check its availability. No matter what a fuel filter or feed system has been clogged. And the carburetor itself can be closed.

If you do not have experience in repair and cleaning - trust this work to specialists.

With a worsening of air supply, the saw should start, but it will work badly. Remove and rinse the air filter. Put it in place only after complete drying.

If the saw is well started, it works at idle and stalls when serving Gaza - Most likely the muffler is scored. Remove, disassemble, wash, put in place and work on.

It is easy for your own hands you can also change the saw bus and chain, carburetor, starter, oil pump, ignition and clutch.

Here is a video full disassembly of this saw:

And replace the torn starter cable to you will be able to quickly after viewing this video:

More complex repairs of chainsaws associated with the replacement of a cylinder-piston group or crankshaft, we recommend to entrust to those skilled in the art, although if you are familiar with the two-stroke engines, then this work will not be a good work, and parts for a chainsaw partner - not a shortage in Russia.

To enlarge the pictures, click on its thumbnail.

Operating Instructions for partner 350

IN this Instructionyou will find not only a detailed description of the saw, but also the main techniques of work with the tool. We want to draw your attention to that this chainsaw can operate on gasoline AI95 or AI92 with the addition of oil for two-stroke engines in the ratio of 1:50.

Carburetor adjustment Chainsaw Partner 350

Disadvantages of saws

In the Russian market, you can meet not very high-quality fake chainsaw partner 350, which is not only an additional evidence of its popularity, but also harms the brand as a whole. Yes, and other models of this brand are successful in summer houses and farmers.

If you are ready to consider a partner 350 as your home tool for sawing the lacrimal trees, cutting the boughs and other not very voluminous work, then there should be any cons: more often than others called their owners:

Dear readers, if you have any questions, ask them using the form below. We will be happy to communicate with you;)

Today, during repair or any kind of construction, it is impossible to do without chainsaws. From the quality of its work will depend on the entire process of separating wood and the implementation of the planned project of the building. That is why it is worth carefully treating the choice of high-quality chainsaws, which will allow practical and more qualifying the process of dividing construction elements based on wood.

An excellent example can be the acquired chainsaw "Partner 350". But, like any other type of chainsaw, it can come into disrepair and demand repair. To accomplish it, it will be important to correctly understand the cause of the breakage and correctly replace the elements exhausted its resource.

As a rule, the repair can be made independently, it is only necessary to understand where it is better to start. Given the work of the oil pump or the existing carburetor. To do this, it will be necessary to explore the device and the principle of work chainsaw "Partner 350".

Characteristics

Use chainsaw "Partner 350" with an engine with a capacity of 1.8 hp Allows you to not worry about the jamming of the chain, letting the ability to perform necessary volumes work on the workpiece of wood or maintenance construction work. This is ensured by the automatic inertial brake and lubrication chain during operation.

The CCS system with a powerful air filter allows the aggregate timely and does not allow it to overheat. The saw has a low production noise due to the correctly designed body, which is quenched.

An existing chain step at a 3/8 inches allows you to evenly distribute the applied load. The fuel tank capacity of 0.4 liters provides required amount Fuel for long work, and does not waste the design of a saw of 4.7 kilograms. The engine volume is 34 cc.

Advantages when using this model

When using chainsaws Partner, you can guarantee the perfectly produced cutting and separation of wood. With all this, you can mark some benefits, namely:

ease of service and service repair can be performed almost any person;
reliable case and practicality of use due to lightness chainsaws;
minimal consumption of fuel and oil;
ergonomics of each of the chainsaw elements;
the possibility of using high and low temperatures air.

These criteria make it possible to talk about widespread benzopils: under difficult weather conditions with a large amount of work in minimally taken time time.

Technical nuances, device and adjustment of the carburetor

When adjusting the carburetor, it is important to perform a detailed disassembly and clean it from the available dust and dirt. Establishing additional care for connecting elements and housing.

Chainsaw "Partner 350" has several levels of protection, both for the oil pump and for the carburetor. This allows you to say that it is necessary to carry out the adjustment and configuration of the carburetor operation, taking into account future hardware.

It's important to know: In the process of disassembly, the removable elements of the chainsaws must be sequentially decomposed in a separate place so that later in the same sequence could be collected without losing a single element from the components.

When disassembling chainsaws, it is important to correctly disconnect the carburetor so that after it is adjustable. By accessing the internal component, the fuel hose and drive thrust are separated.

The cable tip is disconnected. On the left plot from the fitting you can remove the chain of the benzing.

As a result, a perfectly removed carburetor will be obtained, which can be fixed and adjusted in detail.

There is an interesting article about how.

If you are interested in knowing how to sharpen chain chainsaws at home, then you can read about it in detail.

Instructions on disassembly chainsaw "Partner 350"

First of all, the top cover of the chainsaw housing is removed, then it will be possible to begin the separation of the foam rubber on the surface of the air filter. All device and elements are attached to bolts, which makes more practical use Aggregate without fear of damage at large loads.

With the help of tuning screws, the carburetor is adjusted, each of which performs its function:

1. Helps to adjust the upper speed.

2. Low.

3. Idling.

Tip: For the first time, the adjustment is better to hold under the supervision of an experienced specialist in order to avoid the tool breakage.

Essence settings: Clockwise increase the number of revolutions, against - reducing.

It should be noted that the overheating of chainsaws is excluded, even with a large amount of work performed, due to a powerful air filter and base metal in the carburetor housing.

A practical and simple device allows you to use the "Partner 350" chainsaw in the most different conditions. However, to extend the life of it, it is necessary to use high-quality lubricants (They are more expensive than Chinese analogues on a couple of hundred rubles).

But the damage caused due to the use of unsuitable oil can cost you the cost of the chainsaw itself. Also, do not forget to merge the remains of fuel from the tank, if you do not plan to work over the next week.

Below, we suggest you watch a video about how to repair chainsaw partner your own hands:

Repair chainsaw "Partner 350" with their own hands. Malfunctions and ways to eliminate them

Saw " Partner 350 "has decent power and is very convenient to use. However, the flywheel in this model is not intended for long-term work. If the engine is overheated, various breakdowns may occur. To make repairs yourself, you need to know the chainsaw "Partner 350" chainsaw.

Problems with starter

Starter often fails. In this case, repair chainsaw « Partner 350 "do it yourself, you should start with the following: Unscrew the side cover located next to the gearbox. Starter on a saw is located next to the engine. To check this part, the air damper is first removed.

Then you need to turn off the carburetor. The starter in this model is connected to the throtsel. To separate them, you need to use a screwdriver. If the starter shows increasing, this part must be completely replaced. In this case, the standard modification is installed, and it is not difficult to find it in the store. However, it is best to buy spare parts for Chainsaw "Partner 350" in specialized workshops. After replacing the starter, it remains only to re-tighten the throttle and put the carburetor with the lid.

Flywheel does not work

Flywheels in this saw break quite rarely. Most often, this is due to engine overheating. In this case, the repair of chainsaws " Partner 350 "with their own hands should begin with removal protective coating. After that, the engine is first checked. In some cases, the tire can burn out. If he did not darke it, you can immediately turn the flywheel.

To make it easier to get it, you must first disconnect the crank. It is located right above the flywheel. To do this, you need a cross screwdriver Phillips. After that, the flywheel can be easily unscrewed from the panel. Special attention should be paid to the study of his head. If it is deformed, then the flywheel will have to be replaced. In this case, in the store you need to specify the exact diameter of the head.

Repair of drums

Read the same way

Damage to the plunger in a saw is accompanied by a loud sound when turned on. In this case, the repair of chainsaws " Partner 350 "with their own hands should begin with an inspection of the fuel system first. The problem may be a carburetor failure. In some cases, the drum drops due to the handle that comes out of the grooves. To check it out, you need to open a protective cover. Then the throttle is removed and the fuel system is checked.

All tubes must be connected. After that, it is necessary to check the crank, located above the carburetor. If he disappeared from the grooves, you can fix it yourself. However, if it is strongly deformed, it will need to be replaced. The drum in this saw is located next to the air damper. When he hits a clutch, his protective ring is damaged. If it is completely destroyed, the drum must be completely changed. In this case, you need to know product labeling. When installing the drum, it is simple enough, and you can independently control the installation. In this case, it is important not to damage the fuel system during the repair.

Replacing the connecting rod mechanism

The mechanism of connecting thrust is quite complex. This is a chainsaw "Partner 350". Its malfunctions are often accompanied by loud engine operation. It should also be noted that when cracked mechanism breaks, the carburetor often goes out. In this case, the repair of chainsaws " Partner 350 "do it yourself more appropriate to start with checking the ignition module. It will also be necessary to fully check the clutch. In particular, the condition of the centrifugal coupling is noteworthy.

Disassembling Chainsaws Partner 340s / 350s

Learn more on our website: let's be friends in: ours.

Repair Chainsaws Partner 350 "Part 1"

Does not start chainsaw Partner. The carburetor for 7 bucks, disadvantages, how to fix.

To check it, you need to remove the top cover. Straight clutch in this model is located near the carburetor. To achieve a centrifugal coupling in a saw, the flywheel is removed. Then the head of the carburetor is disconnected. In this case, it is important not to damage the fuel system. Installed centrifugal coupling on bolts. You can disable this part using the key. If cracks are visible under the cylinder, then the coupling must be changed. However, some experts are advised not to rush. If the cracks are shallow, you can try to wind the surface to the file slightly.

Close air intake

The respirator in the model is clogged when using low-quality fuel. In this situation, the Piston Chainsaws "Partner 350" should begin with an inspection of the carburetor. To see it, you must remove the top cover of the device. Then the ignition module is twisted. After that, it is important to immediately disconnect the crank. In this case, you need to use keys. The next step disables the drum.

Read the same way

Right behind him is a carburetor. You do not need to remove it for inspection. First of all, the throttle is checked. In some cases, the problem may be in it. If the choke is in order, you need to look at the bus. When he is damaged, his sides are slightly shot down. Cracks can also be observed in the central part of the tire. If the item is deformed, it will need to be replaced. Spare parts for chainsaw " Partner 350 »Get better in specialized workshops. It is difficult to put a tire on the carburetor yourself. In this situation it is more expedient to contact a specialist.

Cleaning carburetor

For fuel, a very demanding chainsaw "Partner 350". The repair of the carburetor is performed when its nozzles are contaminated. In this case, it is necessary to check all internal mechanisms. When fuel leak occurs, there should be a trace on them. If the hoses are in order, you need to inspect the carburetor directly. To do this, the cylinder is first removed. In addition, it is important to remove the crank, which is located next to the coupling.

After that, it will be possible to look at the carburetor. It consists of the lower unit, as well as the upper part with the ignition system. To unscrew the item, you must use the keys. After disconnecting the carburetor, it is necessary to check its base. If it is not deformed, the problem lies in the ignition system. In particular, contacts can burn out. Separately, they, unfortunately, are not replaced. In this case, you need to buy a new carburetor. Install it will be quite simple.

Chain problems

A special trap is used to control the chain, which also has a 350 Partner partner. Faults of this type are the result of the malfunction of the device. As a result, the chain may hang after a while. In such a situation, the repair of the saw should begin with an inspection of an aspect. It is located next to the handle. In this case, you do not need to delete it. If the stars' teeth are not deformed, you can simply try to lubricate them with engine oil.

In addition, it is important to check the trap. In the device it is quite simple and is a set of rollers. When the trap breaks, they are knocked out of the chain. They cannot be corrected independently. The only option. Put a new trap. To do this, use a screwdriver. Fastening is carried out on three nuts. When installing traps, please note that the rollers are located at the top and must be near the chain.

Repair of throttle valve

If the chainsaw "Partner 350" does not start, the problem may be in the throttle. In this model, it connects directly to the coupling. When the engine has a big load, it does not get up and explodes. In this situation, the repair of the saw should begin with inspection of the coupling. To get to it, you need to unscrew the protective lid model. Then you just need to remove the crank.