Creating jewelry from jewelry epoxy resin. Epoxy decorations: photos and master classes Ring from epoxy resin do it yourself
Greeting everyone! All who love to work with the resin and who loves the "kitchen" of creating something with their own hands!
So, I started with the fact that I chose from my stocks, those flowers that I want to pour, and outlined the desired contours of the progress on paper (plants should be completely dried). You can skip and fill without a stencil, but I wanted to fit the plants \u003d))
I chose the flowers of heather, forget-me-not, and Veronica Dubravnaya.
Now you need to prepare a resin: to miss (according to the instructions!) And leave about 2-3 hours (for a set of viscosity). Immediately after kneading in the resin, there are so many bubbles, they will go away after a while and it can be used. At this stage, it is well pouring into forms. But I'm waiting for it thickening.
While the resin insisters the number of stencils I need and cut out:
An important point is to prepare the surface on which products will be bought. It is longer to be as smooth as possible; Dust If you do not remove before fillings - it will be on future earbrush-earrings. In my case, the surface is glass, and with building level You can put it as soon as possible, putting something under it.
The next step is to put a file or several files on a flat surface. UNDER We will place stencils.
We finite a bit of thickened resin right on the file and distribute the toothpick so that the height was about 2-3 mm. Before You need to cover the lid dome! Experienced way I found out that under the low dome, the probability of dust sticking is less than if you cover one common and high. After 15-30 minutes, the resin can crawl away from the contour, then you also need to be restored to the place or drop more resin and distribute.
Now forget about the resin for a day. It is necessary that the new bases have to get completely and then you can separate them from the file (you can separate it before, but not the hardening resin will bend and leave the fingerprints) of the edges of course they will not be perfectly smooth, so emery paper or filling need to be processed. If there are paired elements for example earrings, then you need to make them as symmetrical as possible.
The files themselves are convenient to use when working with a resin! Thereby protect your table from the resin stuck to it.
We are kneading a new portion of the resin, we leave to bend yourself and meanwhile trying the location of dried flowers and if everything suits you to continue!
After the bubbles came out of the resin (30-60 minutes) we drip the base for a couple of drops, distribute them and have flowers. It is necessary in order to fix them in the right place. Cover the lid and leave to dry.
Well, here was another day)) (or half a day). Again, we prepare a new resin, we leave for thickening, but not much! Otherwise, when pouring too thick resin, the formed bubbles on the plants will be difficult to remove and you can break the twig or leaf, which kicks off the toothpick! It is better to use its average consistency, which looks like fresh honey). This fill is needed primarily so that the resin is flushed into all the irregularities of the plant. Let me remind you about even working surfaceBecause if at this stage it will not be smooth, then the resin simply strokes and spoil the mood and work. The higher the lens need to be formed, the smaller there should be a surface!
Further according to the famous scheme: cover with a lid, leave to dry). The day you need to dissolve a new resin and wait for her thick consistency (thick honey) and pour again to form a bulk coating. Remove before Full Drying for an anti-type shelter on a flat surface (complete drying in different industries resin is different, but it is better to be restrained and not touching products for several days; if there were no fingerprints of fingertips, of course)
After complete drying, we turn the finished face and we make another fill with thick resin, because There are no plants on it, you can make only one fill so as not to leave a flat back surface and remove the file texture! Thus, the plant turns out to be inside the form. The form at the same time becomes very durable and it will not be broken, just to cut))) This whole job seems simple, but to make everything neatly need to have a certain share of patience and skills!
Decorations made using resin require a careful relationship and do not like the open sun (plants can burn out long, for example on the windowsill)
When all the fillings are completed and dried away, you can make a planned decoration (it is upright to make a hole with the thinnest drill) well, or to use as a soul. I like simple forms and a minimum of decor, so it turned out such decorations and photos in me in a new winter:
Suspension with a sprig of heather 20 x 80 mm
Earrings with forget-me-not at Silver Schwenza 28 x 70 mm
Suspension with a twig of Veronica Dubravnaya 30 x 62 mm
Earrings on Silver Schwenza with Veronica Dubber Twin 23 x 64 mm
Thanks for attention! I wish you all the inspiration and implementation of your ideas!
Decorations created using epoxy resin And the Molda is striking the original appearance. This master class will be represented step-by-step instruction, complemented by photos and detailed description Each stage. Repeating all the actions of the wizard, you can independently create a unique decoration that attracts attention to others.
So, for our work we will need:
- epoxy resin;
- silicone molds that are combined with epoxy resin;
- disposable gloves, plastic cups, syringes, sticks for mixing ingredients;
- decorative elements: shells, colored pebbles, dry flowers;
- powder, stained glass paints and potal;
In order not to stain the surface of the table, work is better to perform on an ordinary file. The pendant of the hemisphere will look beautifully if you add it with dandelions. We will need two dandelions for work, so that you can compare how they look at the finished version.
Before work, neatly rinse all the most cooked moldes, dry them with a cloth. Jump disposable gloves that protect the skin from unwanted damage. After that pour into plastic cups with a resin and hardener. In the future, they will be convenient to recruit in the syringe. Perform all actions to create jewelry in a well-ventilated room.
Someone required amount epoxy resin and pour it into clean plastic cup. Using the syringe, type a hardener and add it to a cup with a resin. Different manufacturers indicate different proportions necessary to obtain the result. Therefore, read the instructions specified on the package. It is important to carefully comply with all the recommendations of manufacturers. The quality and beauty of the finished handicraft directly depends on the accuracy of calculations. In the event that you mixed epoxy resin and hardener, and the mixture did not frost, it means that the proportions are violated. This may occur due to insufficient thorough mixing of the ingredients.
If the syringe has rubber insert, then the hardener will not splash. The resulting mixture is stirred in advance prepared wooden chopsticks. You can use skewers for kebabs. The solution should be interfered for ten minutes with circular motions.
The dandelion is very neatly laid in Mold. Parachutes that interfere with work can be removed using a tweezers.
After stirring ingredients, you need to leave the resin for half an hour. This time is enough to have passed all chemical processes. To see what a chemical reaction occurs, as a cup of a cup. It will be heated. It is not recommended to work with epoxy resin in hot weather, as the reaction proceeds quite violently and for half an hour, the resin is fully frozen. Although, different manufacturers offer different epoxy resins.
Gently, thin jet, pour the dandelion epoxy resin, placed in Mold.
After the frost, the resin will fall a little. Therefore, it should be poured into Mold with a slight margin (bulge).
Now let's try to make beautiful rings from the washed by sea of \u200b\u200bglass.
So, we take a little resin, lay the pebbles and pour them with a mixture as as when working with a hemisphere. There should be a small bulge.
You can make earrings with parachutes from dandelions. Pour a small amount of resin and gently distribute it with a stick. At this step, the resin thickens slightly. This will help parachutes to stay in the position in which they were laid.
Make a bunch.
Top pour a little resin to get a bulge. If it works very neatly, then the minimum grinding of the product will be needed.
Similarly, a truncated ball is created. Fill half of Mold resin.
Using toothpicks or needles, put the required number of parachutics.
Pour the epoxy resin in Mold.
Now let's try to make a beautiful bracelet decorated with seashells. In a special bracelet mold pour the resin. By this time, epoxy resin became even more thick. This is necessary for us. Add pebbles into Molds, seashells. Grinding seashells stick to the walls, creating the impression of a suspended state.
About half an hour ago, a new portion of resin was prepared. It should be pouring into Mold from above. It is necessary to perform this with special accuracy to avoid the occurrence of bubbles. What if bubbles appeared? Heat the oven to the temperature of 80 degrees and place Molds there with resin. Leave in the oven until the temperature increases to 204 degrees. After that, bubbles will come out.
Make sure that during the operation of the Molda was in the smooth position. Otherwise, the resin will freeze under the tilt. Remember that the more careful you will work with the epoxy resin, the less you will have to grind the finished product.
Now leave Mold for a day until complete drying. In order for the surface of the future product to do the garbage, cover the mold with a box or lid.
While the bracelet dries, you can make a pendant. We start working with the creation of the main background. To do this is applied to the workpiece liquid plastic. Cover it polymer clayrich in a thin layer. The resulting composition is baked in the oven. After cooling, you can proceed to work.
Pour a couple of drops of resin on the surface. With the help of a tweezers of dried leaves or colors, a composition is compiled. In this case, the resin is glue. It will not allow the composition to budge. Do not apply to create a composition of fresh flowers. Over time, they turn and lose appearance.
On the back of the coulon there is a holder. It should also be put in Mold for creating smooth surface. It is not necessary to think over the composition in advance. You can create masterpieces, improvising.
As a result, it turns out a unique picture. The craft must be dried. When it gets dry, the second layer of resin is poured, forming bulges.
After a day, the bracelet hardened and can be taken out of Molda. This is the upper part of the product.
In the same way, rings, earrings and pendants are created.
Beautiful hemisphere decorated with dandelion.
Unusual truncated transparent balls with parachutes.
You can still make small decorative hemispheres.
Earlier rings, decorated with sea glass.
In order to give epoxy resin bright tintYou can add a little powder or stained paint. If you decide to use stained paint, add them to the resin quite a bit. Otherwise, it is possible to break the proportions between the resin and the hardener. Ready product Do not harden, but will become sticky.
If you add Patal, you will get very unusual decorations.
And these are beautiful lenses, decorated with paratroopers of dandelions.
The reverse side after drying remained at the level with the edges.
it back side Coulomb, which turned out after frozen resin.
It should be accurately polished. In order not to breathe dust, you can use the respirator.
After grinding, it turned out such a rear of the hemisphere.
All sharp and uneven edges must be carefully grounded after frozen resin.
Similarly, we do the bracelet. You can use a special machine for manicure.
If working carefully, then the minimum grinding will be needed.
Grinded edges can be covered with varnish. The layer of varnish must be very thin.
After it gets free, you can enjoy the result from the work done.
A very beautiful frame is chosen for the coulon, which is decorated with a miniature steel butterfly.
And epoxy, and jewelry wire, in the sense of jewelry, special. The usual wire does not cover and darkens with time. This can of course use as an adventant, but not the fact that the oxides will not spoil the product in the process. More or less suitable aluminum wire can be in flower shops. But again, most likely without coating.
We take a wire soft enough, but not too thin. I have an aluminum 1.5 mm coated. We fold the ring. It is advisable to use some kind of obviously smooth shape.
Ringing the long end of the wire. Keep in mind that at the same time one tip (here it will be right) will be sharp, and the second is perpendicular to the wire that we need.
In the same way, cut the tail is very, very close (and better even with a meager margin) to the first slice.
Connect the ends of the ring. The more dense they will lay down to each other - the better.
And now we stick our ring on a wide scotch, koi, it is preferably to fix on a flat surface (I have a ceramic liqueflash or glass) sticky side up.
Since the epoxide is better to breed at least 10 ml, then the billets should be done immediately, if of course you do not want to throw out the excess diluted epoxy. It is very important to check the density of the ringing of the ring to the surface.
Next, I fill the framework with artistic garbage - inlays. Actually, they advise first to pour down the bottom layer, and then pour rubbish, but since the time from the knead to the frozen epics is limited, then I do in a different way.
So, the billets are decomposed, tightness is tested, you can breed.
I use Ice Resin (odorless, liquid and almost does not give bubbles - the last very important). I doubt the same number of resin and hardener ...
It is very important to measure the exact amount of liquids. Epoxy - insidious thing: a little more hardener and it will begin to "goat" (that is, it is for such horns behind the tool) too fast; A little less - and you will wait until the lenses are frozen forever. :)
Once again: Epoxy Special, Jewelry Ice Resin or Crystal Resin. Industrial is distinguished by lack of smell, greater transparency and less bubbling. I ordered here: http://vkontakte.ru/club13872192 - That's it ...
Once upon a time she tried to fill with epoxy glue - quality is much worse, it's more difficult to work with it and in general it is not intended for jewelry purposes.
Kneading. Initially, the resin is muttered, the opalescent divorces appear in it - this is normal. We continue to interfere with another minute and a half ... until the mixture becomes transparent. Large bubbles will get out, small gradually too. However, in the product they will need to help "hatch." From the beginning of the knead and before the "rowing" epoxy from us somewhere 30-40 minutes.
Pour straps. I use the rubber stack for oil (it will be further in the frame), they also save bubbles.
Primary fill, as can be seen in the photo, does not cover "trash" completely. This is normal. At this stage, we only need to create a "bottom" and consolidate the drawing. You can even pour even less - in the framework of the lower right corner I stopped. :) For all about everything we have half an hour: pour, drive out with a needle or stack of bubbles, make sure that the lenses are flooded more or less evenly.
Now I exhale the clock by 8-10 and hide our signs with fills on the far, freed from the dust shelf and cover the lid, leaving between it and the shelf of a small lumen for air.
Stage second. After 8-10 hours, lenses are ready to the secondary fill. We repeat the epoxy and gently apply the second layer. He must cover all protruding details.
Epoxico does not contain solvents, so does not give a shrinkage when frozen. In addition, it is viscous, so if you pour it "with a slide," it is submitting to the edge and stop there. But it is important not to overdo it.
After another 8-10 hours, we turn our straightforwards from Scotch. On the
This stage they look scary. Now we take the solvent and wash the remnants of the tape glue. Suitable alcohol, gasoline, white-spirit, acetone or a rehemor for nail varnish.
Fill from the involve the third layer and the land of 8-10 hours. Voila. :) You can drill, insert in a rim, soaring the wire and everything else that the soul will wish.
And still work from epoxy
My favorite heather. :)
Bracelet with heather
Poppies plastic, but the petals of Melissa and Traviki natural (here, the herbarium was useful%).
Bracelet "Fresh Water". River pearls, pearl and other garbage. :)
Yashmovy crumb, adventuric glass, fluorite sand and pearl crumb in jewelry epoxy and gilded wire. Suspension "Tie"
Lazurick crumb, pearl, dried heather, fluorite sand in epoxy and gilded wire. Bracelet.
Bracelet and medallion.
To date, fashion rings made of epoxy resin are quite popular, they have a variety of form, as well as various additives and fillers, can also be given any color. In the workpiece, you can put the chips, sequins, or pour some insect, everything turns out very beautiful and interesting, and the main thing is unique that in our difficult time it is in the first place.
Despite the seeming complexity, all the technology is quite simple and understandable, you just need to delve a little into the process and you yourself will be able to make a dozen rings of different sizes)))
The basis is epoxy resin and a hardener in the ratio of 10/1, sparkles and wood chips are added. Initially, the required number of resin is poured into the container, then sparkles are added to it and everything is thoroughly stirred, then stirred and stirred again. It is painted with epoxy resin with a kel, add to a little bit at the tight of the toothpick, mixing the need to catch the desired color. The hardener is added to the last stage in the ratio of 1/10 on the total fraction of the resin, that is, for example, 10 grams of resin and 1 hardener gram, everything is very thoroughly mixed.
And so, let's look at what exactly will need for the manufacture of an epoxy resin ring?
Materials
1. Epoxy resin
2. hardener
3. Sequins
4. Wood chips
5. Kerker
Instruments
1. Capacity for the preparation of the solution (plastic cups)
2. Silicone form
3. News
4. Pliers
5. Drill
6. Round file
7. Waterproof sandpaper with grain 600/1200/2500 Grid
8. Mini-grinding machine
9. Schunzirkul
Step-by-step instructions for the manufacture of an epoxy resin rings with their own hands.
The first thing you should prepare all the components, so that in the process of work everything is at hand, it is also necessary to wear latex or mica gloves, because the resin is very sticky, and the hardener is aggressive when open areas Skin can be bored, so safety is primarily. The respirator is also a mandatory measure of safety from steam of resin and hardener, in small quantities of course not so scary, but still ..
To fill the blanks, it is best to use a silicone form, because it is very simple to remove the filled figures, and there is nothing to stick, the same form can be made of paper and inside the scotch, also a good option to start working hours)
It is advisable to spread the table or a simple package, so that the resin drops, the ring and hardener did not drink the surface of the table.
After that, the author pours the epoxy resin into the container, adds sparkles and brings to a homogeneous mass, then wood chips, the roller adds to a slightly at the tight of the toothpick, so as not to go through the contrast. In this case, the author used 3 dye: black, blue and green.
Everything is very thoroughly mixed.
Next is important! It is necessary to drive air bubbles from the solution and this author does with the help of a homemade vacuum installation. Ie a cup with a resin is placed in a jar and for 10 minutes the air is pumped out there. Additionally, the resin can be warm up in a water bath up to 50-60 o
thus, it will become more elastic and air bubbles will be released much faster.
The epoxy resin with the added hardener freezes after 24 hours, from silicone shape, frozen blanks come out quite easily.
These are such blanks for the manufacture of rings are obtained. The work is very dusty, so we change clothes into work clothes, protective equipment: respirator, glasses, gloves.
Then begin to grind the ring from the inside, the sandpaper was used with grain 2500/1600/600. Mandatory from the inside, because by the inside the degree of polishing the product will be determined.
The outer part of the ring is polished by waterproof emery paper.
Starting with large grains and gradually reducing up to 600.
Wiring a ring of borob machine with polishing paste. The author bought it in the auto shop.
In general, as a result, it turns out that beauty.
All data rings by the author made to order, and sent by mail to customers in all regions of our huge country. How do you know the product handmade We are always in demand, but in our time especially, payment for the author's rings is worthy. So you can take the basis for small business at home, a set of tools is minimal, the materials are available in free access and sell, so we take and do. Dare friends!
This end my article. Thank you very much for your attention!
Come visit more often and do not miss new ones in the world of homemade!
The resin is spilled on the portions, dyes, sequins, the knife (did it, from the bearing cage) chips, shapes for fillings (silicone - the most convenient) and / or you can do paper, sticking with scotch. (quietly the workpiece can be removed), cups for additional mixing and still be sure to work in gloves (or latex sold in pharmacies, or in the store "All for 51 rubles" I bought from the Codefana)
The first stage - mix the chips with the resin and the caller, these dyes give a bright, dense, color, so add to the droplet, on the tip of the toothpick, to the desired saturation
in this case, I used 3 dye black, green and blue.
added glitter glitter on the simple))
We mix the resin with the hardener in the specified proportion of 10 parts of the resin 1 part of the hardener. For which white cups are overflowing a mixture of hardener resin and again mixed, as non-mixed resins and a hardener can remain in the initial cup, and if pouring into the form, then it is unpleasant to surprise the billet. Therefore, we transfix and mix again. In the mixing process, in the resin, air bubbles appear and get rid of them as follows
there are more secrets - before vacuum processing of resin, we warm in hot water Up to 50-60 degrees, it becomes fat, and bubbles leave the resin faster. We evaporate for 10-20 minutes. After that, you can pour into the form.
after the cock and goes to 10-15 minutes - we remove small bubbles with a lighter and leave for 24 hours before a complete rejection (according to the instructions). Practice shows that the heated mixture is pouring completely in 4-5 hours. The simplest ended.
here, I pulled out such cubes in the morning.
Processing ... Here you immediately wear clothes for dirty works, and necessarily a mask - since dust will be much very much, and if there is an opportunity to do everything in a check room and / or with an exhaust.
I am much easier to take a job and there you use to sharpen and drill at home machines conventional drill For drilling and file))) First of all, I will drive in the center of the billet hole with a diameter of 12 mm and then go from the square to make a circle))
that's how I look after the turning on the workpiece on the machine with an exhaust. Therefore, I remind it once again, it's a lot of stacking "
rablicking to the almost necessary size.
And the first "meditative" process with emery paper-cutting grinding rings begins. Unsuccessful photo, but the essence is clearly becoming a form.
And the responsible stage begins - "fall into size"))) because 15 mm and 15.5 mm are a huge difference for comfortable wearing rings. Girls in the know What does the little ring-finger mean and remove the ring without the help of soap, cream, the thread is very difficult (it is not necessary to mock :-))))
And the second "meditative stage" grinding begins. For this, I use waterproof (important) emery paper 600,1200,2500 grid.
We make the entire grinding with water - the water does not give a "score" sandpaper. Each ring "skip" through all skins from 600 to 2500 - we remove all scratches. I usually start from the inside and from how well I am alone inside, so the ring will look outside. Over grinding one ring I sit about 30-40 minutes and final processing- Polishing. Polishing paste I bought for a weak on the car market, "for optics with plastic glasses" and with the help of an engraver, the rings acquire their final appearance.
I dedicated all this week to work on orders from Rakhman from Grozny
Alexandra from Moscow
Oleg from Kolpino
And Yulia from St. Petersburg
Rahman, Alexander, Oleg and Julia you saw how to make your rings. Thanks for attention.
Why you can not give icons
Is it possible to give icons as a gift: Signs, the opinion of the Church
A year ago left her husband, and now I do not know what to do