Warming of a metal trading pavilion (container) with their own hands. How to build a shopping pavilion Lark for trading with your own hands

Speed \u200b\u200band ease - a kind of motto modern technologies. In construction, it is relevant as well as in the Internet sphere, only a low mass of elements is meant, and at speed - the speed of their compounds, and, it means, short times Construction of buildings.

Fine modern tool SIP panels protrude to achieve speed and ease.

Fast-based buildings

Under this concept implies such structures that, thanks to their design, make it possible to significantly reduce the construction time. Several ways or combinations are used for this.

LSTK technology - a method in which the basis of the building is metallic or even wooden frame. During construction, thin-walled, light steel galvanized profiles are used - perforated or solid, allowing you to collect a sufficiently rigid construction in the minimum time. Frame structures Can be combined with reinforced concrete.

Sandwich panels - Material used for facing the frame of a quick-scale building, as well as for insulation or reconstruction of traditional. The plates are more often used, however, products that are assembled in place in the installation process are also available. As a rule, it is associated with large volumes or complex architectural elements.

Both technologies are widely used together, allowing to build industrial and residential buildings with extraordinary speed. Fast-based pavilions from sandwich panels - the most popular option of building a trading point, but the material allows you to build a large hypermarket also quickly and economically. In the photo - the shop building.

Shopping Pavilions from Sandwich Panels

For trade, the speed of turnover and the opportunity to organize or postpone the store as quickly as possible, largely determine the success of the entire enterprise. The need for mobility of the kiosk, especially if we are talking About seasonal trading, so great that the enterprising owner prefeals a primitive counter under a canopy or even a tray, stationary and, of course, a much more convenient building, only because the latter is being built too slowly.

Construction of pavilions from sandwich panels solves this problem. Mounting them is so simple that can be done with your own hands. In most cases, buildings do not even require the foundation.

Structure Sandwich panels

IN general The material is a three-layer element consisting of a thermal insulating layer in a metal trim, PVC, plate OSB etc. Not all types of products are used to build pavilions.

The heat insulator - the plates filler can serve as a mineral wool - basalt or glass, as well as polystyrene foam and polyurethane foam. It is recommended to build a pavilion from the sandwich panels, which include polymers. This is connected with two factors. Mineral wool is quite high and not too devices to the action of moisture, but for kiosks that are constantly exposed to rain and snow, moisture resistance means a lot. Polyurethane foam or polystyrene foam has no smaller thermal insulation properties, but it is much more stable in relation to moisture, and products of them have a smaller mass.

When building a trading pavilion, it should be noted that the filler refers to the category of self-fighting or non-supporting polymers burning, which indicates the corresponding marking. Unfortunately, the kiosks often become a victim of hooligan actions, and therefore their fireproof must be maintained at a high level.

Opening - Steel is recommended - galvanized, with polymer coating, or aluminum. Metal provides products, and, it means, the trading pavilion is greater durability and durability. And the coating plays the role of protection of metal from corrosion and tells the building a nice appearance.

The metal panel sandwich is produced with a smooth, profiled, corrugated surface and are painted very diverse. The photo is a quick-scale pavilion from SIP-panels.

Construction of shopping kiosk

Due to the ease of material - from 30 to 80 kg, and the convenience of installation, the project work can be carried out with their own hands. Small pavilions do not even require the foundation - quite smooth concrete siteAnd do not need to apply heavy construction equipment.

The pavilion project from the sandwich panels can be ordered, found on the respective sites and even calculate yourself if there is an appropriate experience. As a rule, the calculations are carried out on the basis of the parameters of the selected panels, since this product, because of its structure, is poorly adjustable, and therefore it is desirable that the project allows you to use standard stoves.
At the second stage, the foundation is erected. Since pavilions made of sandwich panels have a very small mass, the foundation builds a lightweight-melco-powered belt, tape-columnary and so on, or a ready-made concrete site is used.
Constructs metal carcass. First, the design of walls and roofs is assembled separately - the width of the profile should be clarified in the reference to the load on the building. It should be remembered that frame structure Pretty large sailboat, which increases the load. Then the walls and roof are associated.
Mounting the walls with their own hands begins with corner elements. When docking the panels between them, heat-insulating gaskets are stacked, and the seams obtained are married. Plates are fixed with self-drawing. The photo demonstrates the working time.
The roof cover is made in the same way, but it is applied to cladding roofing Sandwich Panels.

On video about how to build trade Pavilion do it yourself, told in more detail.

Expert Tips - Business Consultant

Photos on the topic

Starting business, everyone wants to save, and it is quite reasonable. One of the ways of saving when opening a stall is an independently built room. To make a stall yourself, you need to know some moments.

Just follow these simple step by step adviceAnd you will be on the right track in your business.

Short step-by-step business manual

What you need to have: - metal pipes;
- galvanized sheet;
- chipboard;
- polystyrene foam;
- Other construction Materials on your elbow.
So, we will proceed to actions, tuned by a positive result.

Step -1
The easiest and cheapest stall - welded frame. To build it, you first need to install the framework. Best Material For him are metal pipes, because other materials (channel, profile) will not provide your stall necessary strength. After doing this, go to the following actions.

Step -2
Now pay attention to the bottom of the carcass, it will be three-layer. It should be seen by any moisture-resistant material: for example, a galvanized sheet or rubyamaster. It is necessary to protect the interior of the indulgence of moisture. Next layer - plates chipboard, and the third layer - coverage for your choice. After doing this, go to the following actions.

Step -3
Then the finished frame should be sewn. For the trim, you can use a galvanized straightener. It can be applied as a material for the roof. After doing this, go to the following actions.

Step -4
For decoration indoor room It is best to use LDSP. Heat insulating material For the kiosk is the expanded polystyrene or mineral insulation - it will protect from moisture and from the cold. After doing this, go to the following actions.

Step -5
The kiosk door should also have a gasket from the insulation to avoid drafts. After doing this, go to the following actions.

Step -6
Showcases of kiosk can be made of double glass. Take care so that they can be closed with metal shutters. By this, you will protect your kiosk from unexpected guests. After doing this, go to the following actions.

Step -7
Now that the premises of the kiosk is done, the most important thing is to carry out electricity, install sockets, switches.

We recommend paying attention to the following advice of the business consultant:
Install the kiosk is needed at some distance from the ground to avoid moisture and freezing. For this fit concrete blocks Or a small brick foundation.

Additional Information and useful advice Business expert:
A kiosk can be seen not only by a galvanized straightener, but also panels from PVC (clapboard). Both materials have durability and durability.

A corrugated aluminum leaf or linoleum can be used as a floor covering.

Corrugated sheet - Durable material, resistant to of different kind impacts, highly ecological.

Linoleum - happens undoubted and based. The first option has good moisture resistance and low price. Linoleum is more expensive, but at the same time is much stronger.

We hope the answer to the question - contained useful information for you. Good luck! To find an answer to the question you are interested in. Use the form -

How to insulate a metal pavilion? Let us give a general scheme of complex finishing of this room:

On the metal surfaces Moisture-resistant protective film is attached.

The entire trading pavilion around the perimeter is equipped with a frame from a bar coniferous rocks So that the timing thickness is equal to the thickness of the material you plan to insulate the room.
In the cells of the crates, the insulation is laid (mineral wool "Eau return" 100 mm, foam, etc.).
The insulation layer and the frame are covered with a vapor barrier film.
From the inside the trading pavilion (walls and ceiling) is facing with a chopped sheets of a chipboard 16 mm thick or PVC panels.
The floor can be insulated with a multilayer flooring, which includes such components as wood coniferous rocks with a thickness of at least 25 mm, rubberoid sheets, chipboard furniture plates and linoleum.
The final stage is the installation of electricians: Double EURO standard sockets, switch, electrical switchboard with UzO, daylight lamps LPO 2x40.

Applying Polyurethane

To date, polyurethane foam is the most profitable and price and quality material for the complex insulation of metal trading pavilions. This material is removed directly on the base of the roof, the foundation and overlap, as well as on the walls, gender and ceiling.

Speaking about how to insulate the polyurethane foam, a separate trading pavilion with a metal floor, walls and ceiling, it is impossible not to note the advantages of this thermal insulation material:

the indicator of thermal conductivity of polyurethane foam is at the level of 0.028 W / m * hail, and the thermal conductivity of the extruded (solid) polyurethane foam is 0.03 W / m * hail, and this is not the limit;
polyurethane foam is durable in operation and resistant to wear;
components of polyurethane foam do not require special preparation for use and actively react already room temperature (25-30 ° C);

polyurethane foam is absolutely not toxic, not subject to rotting even in a converged medium, and also does not allow to settle inside the heat-insulation of rodents and harmful microorganisms;
installation of polyurethane foam does not require special pretreatment of the surface, including alignment. Foam fills all cracks, gaps and cavities, after frozen forming a monolithic coating without junctions, and hence, with the minimum probability of deformation and destruction during operation.

an approximate service life of polyurethane foam thermal insulation - 25 years, subject to the preservation of the integrity of the coating;
polyurethane foam does not support independent burning, which is very important from the point of view of fire safety.

Heat the Polyurethane Foenerette's shopping pavilion is to get rid of themselves from the need to use additional pairo, moisture and electrical insulating materials and means of protection against corrosion and wind. The internal structure of foamed polyurethane foam in the form of a plurality of small cells is an irresistible obstacle for moisture, and also retains a comfortable microclimate inside the pavilion both in the heat and in the cold. In addition, it is necessary to repair such thermal insulation much less often.

Alternative options

Styrofoam. This insulation is usually mounted outside the room, so it is recommended to protect it a special membrane that protects against mechanical damage.

Glasswater

This material is applied in cases where thermal insulation by foam is unacceptable, for example, if the pavilion is made using a dark shade made up. Such a coating will be significantly hot in the hot season, so the foam is not suitable as the insulation. The glass wool should be covered with a parobararier from the inside and protect from the wind and moisture outside. Use and basalt mineral woolBut this option is more expensive.

Equip the shopping pavilion by Tambour

Very useful and convenient when erecting a pavilion to equip him with a small tambour. His space will serve as a kind air cushion Between the external environment and the microclimate indoors, that is, the cold air will warm up before it gets directly into the pavilion. The walls and ceiling of the tambour are recommended to separate with artificial felt coating.

Of course, in the strongest frosts not to avoid the use of heating appliances inside the pavilion. These can be calorific or several incandescent bulbs. More expensive, but more effective method The heating of the commercial premises - equipment used for heating infrared radiation (film or metal panels). However, your costs will be accumulated, as such devices will allow to significantly save electricity.