How to make a palm tree from plastic bottles step by step. How to make a palm tree out of plastic bottles step by step instructions. Palm tree from plastic bottles: step-by-step instructions with a photo for creating the base of the trunk

Any garden will seem unusual and original if you plant a palm tree there. However, in our climate, this idea is impossible - a tropical plant obviously will not survive the winter. An alternative would be a plastic palm tree. The product is not afraid of frost and does not need to be watered.

DIY materials

There are several ways to make a palm tree from plastic bottles and each uses the same components:

Plastic bottles are brown and green. Better two or one and a half liter.
Scissors.
Tape or glue.
A long, straight stick that will be the base - iron, plastic or wood.
Small wires or twigs for palm leaves.

Stages of product creation:

Wash and clean bottle labels.
Make leaves.
Make a tree trunk.
Fasten the leaves to the trunk and set in the yard.

it short description upcoming actions. Below are some instructions for beginners. Everyone will be able to choose which palm tree will look best in the yard.

First way

Making leaves

Green bottles are cut in half. You only need the part with the neck. A narrow section of it remains intact, and the rest is cut into many small strips. When a lot of blanks are made, they are all strung on a cable.

It is advisable to fasten them with glue or tape so that they are firmly attached to each other. Leaves need to be made at least 5-6. If you get more, the tree will look even more attractive.

palm tree trunk

The barrel needs brown bottles. cut off Bottom part bottom and the rest of the bottle is used. The process of creating a blank is identical to the first point - longitudinal strips attached to the neck are cut.

However, if in the first case the more stripes, the better, then there should be six of them. The edges are neat, slightly pointed and curl inwards. A lot of preparations are needed. The more details, the longer the palm will be.

It is advisable to select the length of the rod on which they will be strung, but it is important to consider that part of it is dug into the ground.

Foundation preparation

As already mentioned in paragraph two - the rod must be dug in. It should be deep enough in the ground so that the structure does not fall from the wind. Brown details are strung on it. The neck of the first workpiece is slightly buried along with the rod.

We fasten the leaves to the palm tree

The blanks from point one should have wires sticking out of the necks of the bottles. With the help of wires, the crown is tied to the top of the tree.

Second way

The actions are approximately similar to option 1. Only the type of parts cutting changes, and from this appearance products are also changing.

In this case, brown bottles are not used completely, but only 1/3 of the bottle (which is near the narrow part). Instead of 6 long strips, 8 short pointed petals are cut out.

To make the palm tree wide and voluminous, the petals should stick out. Due to the lack of materials, the bottom of the bottle can be used in a similar way, but then a hole must be punched in the bottom.

The leaves of this palm tree seem more real. For a realistic appearance, in addition to green bottles, you can use yellow ones. You can also experiment with leaf sizes. For huge sheets, you can take six-liter bottles, and for small ones, one and a half liter ones.

The bottom of the containers is cut off, and the rest is cut into 3 sheets attached to the neck. The leaves have a longitudinal stem (about 1.5 cm) and the rest is cut into many thin transverse strips on both sides of the leaf stem.

In order to present visually - the leaves will resemble, familiar to many, fern leaves. To make the tree lush, the fringe needs to be fluffed - the strips are bent alternately up or down.

You need to fasten the parts to each other, as well as in the first method.

Third way

The leaves are made from the bottoms of one and a half liter bottles. They are cut, holes are made in the middle and strung on a cable. Such a sheet, on the contrary, ends with a thin part of the bottle.

In this embodiment, a thin base will not work. For the base you need to use a long log. The bottoms are cut off from brown bottles and nailed to the log until they cover it completely.

Description of these 3 ways can give creative people inspiration to create new unusual options. A little tip: leaf and stem ideas can be combined to suit the taste of the garden owner.

In the photo, especially skillfully made palm trees from plastic bottles are surprisingly similar to real ones. The yard in which such beauty “grows” will look like exotic tropics, even in a snowy winter.

Photo of palm trees from plastic bottles

Then instead of throwing them away (thereby polluting environment), you can make a lot of crafts out of them.

Crafts can be made with children or on their own. Them and you can decorate the house, garden or cottage.

One of these original crafts- palm. Having created such a palm tree from plastic bottles, you can decorate any garden or cottage with it. She looks beautiful,and you don't need to be a great specialist to make it.

Palm from plastic bottles for beginners

You will need:

Plastic bottles (preferably green and Brown color)

Scissors

Drill or awl

A metal rod, a straight branch or a thin plastic pipe.

* To begin with, wash all bottles and remove labels from them.

1. Cut brown plastic bottles in half, then cut the bottom half in a zigzag pattern.

2. Cut the green bottles lengthwise to get several halves. Cut the fringe on both sides of each half.

3. Make a hole (drill or awl) at the bottom of each of the brown halves. The hole should be exactly the thickness of the rod.

4. Take a rod (metal, wood or plastic) and put the brown halves of the bottles on it.

5. Green bottles (palm branches) can be attached to the top of the trunk with a thin wire that is inserted into each branch and into the trunk, and its ends are twisted.

How to make a palm tree from plastic bottles

You will need:

2 liter plastic bottles

Scissors or utility knife

Wire

Plastic or wooden rod

Glue or tape.

Making a crown

1. Cut a plastic bottle in half (crosswise). Leaves will be created from the top.

2. Cut the half of the bottle into strips that go up to the neck.

* You can also cut the bottle into 4 petals, and cut each petal several times.

3. Take the wire and start stringing blanks from green bottles (palm leaves) onto it. It is worth noting that you need to tighten the lid on the very first blank, so you can fix the petiole of the green leaf with a knot. The same should be done with the last part of the bottle.

* The palm tree with about 6-7 leaves looks beautiful.

* The base of the leaves must have long stalk to make it easier to attach the leaves to the palm.

Making a palm tree trunk

1. Cut off the bottom of a brown bottle, leaving almost the entire bottle intact.

2. Cut the bottle from bottom to top into 5 wide strips (see image).

3. Start stringing brown blanks on a strong metal, plastic or wooden rod to get these palm tree trunks.

Gathering all the details

To attach the leaves to the trunk of a palm tree, use glue or tape. It is desirable to evenly distribute the leaves in order to obtain a symmetrical crown.

A spectacular and eye-catching palm tree from bottles will serve as an excellent option for decorating a summer house, garden plot, playgrounds in the yard or kindergarten. Made by hand according to a simple scheme, it will not only decorate the surrounding area, but also help a person to dispose of a large number of plastic containers.

How to make a palm tree from bottles with your own hands

Those who like to realize the most incredible fantasies will like a master class on how to make a palm tree from plastic bottles. For a tree, dark brown containers are suitable as stem blanks and green to make leaves. If there is no green container, it can be replaced with the most different colors: blue, yellow, red. For trees, containers from kvass, carbonated sweet drinks or beer are useful.

The principle of creating a palm tree differs depending on what the craftsmen found. To form the trunk, you can use a round support made of wood, where the bottoms are nailed, or a cable with wire is suitable, where containers with cut bottoms will simply be strung. Leaves differ in splendor and length. If you want to get palm fans, then they are cut, notched and bent, and the elongated leaves are strung on a cable.

The area of the leaves and the trunk depends on the size of the bottles, but you should not get carried away and use a 6-liter or 20-liter container from under the water. A tree from 1.5 and 2-liter plastic containers of different colors looks much neater. Corks from them will also serve as a material for decoration - they decorate the base of a palm tree, you can make a mosaic out of them for flower beds, walls of houses for children.

How to make palm leaves

To get a spectacular palm tree with your own hands, you need to pay attention to the manufacture of its leaves. To make them, you need:

Cut the green bottles in half with scissors, cut the upper part into longitudinal strips so that the neck of a narrow diameter remains intact half a finger from the lid. The thinner the cut strips of plastic, the more magnificent the crown turns out and the more natural it looks in the photo.
Taking containers for leaves is not necessarily the same - this will not affect the appearance. The resulting blanks must be strung on a prepared hard high-voltage cable with a diameter slightly less than the neck to obtain one lush sheet. The number of leaves varies according to the prepared holes on the metal pipe used as a support. Then they should be fixed on the stem blank.

Step-by-step instructions for making a bottle palm trunk

The next detail in the question of how to make a palm tree from plastic bottles will be the trunk. Step-by-step instruction:

The trunk is made from dark brown dense containers, from which the bottom is cut off right along the contour.
Then the resulting workpiece is cut to obtain segments bent inward, serving as an imitation of a tuberous trunk. Cut them should be 2/3 of the height, without affecting the top.
Make the required number of segments depending on the desired height plastic palm.
When all the blanks are ready, you need to string them on metal tubes. To do this, the container with its neck down sits on another with a slight shift to obtain a beautiful tuberous trunk. The principle of stringing is similar to making a cone. After that, all parts are fixed.

Connecting individual parts and installing a palm tree on the site

The last step on how to make a beautiful palm tree from plastic bottles is to connect all the blanks together. What should be done:

Prepare a rigid solid base from sheet metal approximately 40*60 cm in size and at least 5 mm thick to support the weight.
2 metal rods with a length of 25 cm or more should be welded to the base or holes should be made with a drill for fixing. They need to wear metal pipes desired height This will be the base of the tree. At the same time, the diameter of the pipes is left slightly less than the neck of the bottles for the barrel.
The upper part of the supports will outwardly resemble a revolver drum; for this, 6-7 pipe sections are welded onto them. Bottles for the barrel must be assembled on rods, and palm leaves are inserted into the holes of the "revolver". For fixing, the cable inside them is bent, fixed from the side of the top and inside the neck of the outermost bottle. For the stability of the bottle structure and hiding the ugly lower part, the base is buried half a meter.

To create a mini bottle palm tree that would decorate a room in an apartment, you will need the following principles:

The barrel must be done as follows: cut off a third of the bottle from the neck, cut out 8 triangle petals on each part, without affecting the neck by half a finger. Each segment turns outward to obtain scales. The second half is used in a similar way to save money, but first it breaks through desired hole hot knife.
Wide fan leaves can be made as follows: cut off the bottom from a 1.5 liter plastic bottle, divide the side part into 3 parts without affecting the neck. Give the segment the shape of a petal by rounding at the end and narrowing at the throat. Unbend outward, cut the parts on both sides, form a fringe so that the uncut middle remains up to 1.5 cm wide. For splendor, manually shape each strip, bending up and down in sequence.
Make the assembly in the same way as a large palm tree, only use a simpler base.

Video

With original crafts made from plastic bottles, you can easily decorate your site! Such material is quite durable and easy to process, thanks to which a wide variety of products are created.

For example, you can create a wonderful palm tree from plastic bottles with your own hands! Such an evergreen palm will all year round decorate your site or, for example, a playground.

This master class will help you make such a craft!

You will need materials and tools such as:

- plastic bottles brown shade and green;
- scissors;
- stationery knife;
- thick wire for the frame.

To begin with, it is worth deciding how high the palm tree will be. In this case, the palm tree will be approximately 1.5 meters high, and the second one will be 50 cm. For this, you need about 23-25 bottles of brown shade per trunk and 15 bottles of green shade for the crown!

To create a barrel, brown bottles need to be cut in half as in the photo below.

We need bottles of different sizes, those that are larger to use at the base, and smaller ones, at the top of the trunk. Bottle caps must be removed. You will need both the top of the bottle and the bottom.

Then, the edges of the blanks are cut out in the form of petals, about 6 “petals” should be obtained.

After, they need to be bent.

It should turn out like this.

In the future, they will fold into each other. Since there is no hole for the wire at the bottom of the bottle, it must be made using a hot nail, a knife, or it can also be drilled. Having folded the blanks, you get a rather fluffy trunk of a palm tree.

After all the details on the palm tree trunk are ready, you need to start creating palm leaves!

Bottles can be used in different shades of green. You can also experiment with the volume of containers, for example, use two-liter containers at the base, and arrange smaller ones at the top. To do this, on green bottles you need to cut off the neck and bottom.

Then, cut the bottle into three pieces.

If you want wider leaves, you can cut it only into two parts. You will get such a preparation.

After, you need to straighten the strips in different sides.

This will give some splendor to the crown!

Now, the simplest and final stage in creating a palm tree from plastic containers remains!

After all the details are ready, you need to securely install a frame made of wire or other suitable material at the desired location on the site. And then, string on the frame all the received parts of the palm tree.

Using a large cork from a five-liter bottle, make a retainer on top to securely fasten the leaves. To do this, in the center of the cork, you need to make a hole, a slightly smaller diameter than the frame.

Then, after the crown is fully assembled, put it on the wire!

That's all, it turned out to be a very original palm tree that can be installed on the site or on the playground!

The final look of the craft. Photo 1.

The final look of the craft. Photo 2.

Such a craft will certainly decorate the area, as well as give positive mood for kids, including, like a plastic basket made by yourself!

Exists good way decorate at the same time household plot, and get rid of accumulated plastic bottles. It consists in the manufacture of an artificial palm tree. This article provides detailed instructions on how to make a palm tree out of plastic bottles. Following it, you can easily and quickly assemble a tree of the intended height.

Benefits of palm trees from plastic bottles:

Cheap, as the palm tree is made from waste
A good way to recycle accumulated bottles
Durability of the product due to the fact that plastic containers decompose for hundreds of years
Soft plastic bottles are easy to cut
The simplicity of the design allows anyone to assemble a palm tree from bottles
The palm tree gives the site a tropical touch, helps to ennoble adjoining territory, a playground or an unsightly corner of the garden

Applied materials and tools

To make a beautiful evergreen palm tree from bottles, you will need the following materials:

Green and brown plastic bottles for palm leaves and trunk assembly
Metal or plastic tube to stiffen the barrel
Wire or thick rope for assembling leaves
Scotch tape or glue to secure the leaves to the trunk

From the tools you will need:

sharp knife or scissors for cutting bottles
drill for drilling holes

Bottles must first be cleaned of labels, washed from dirt and glue residue. If there are not enough green and brown bottles, you can paint the transparent bottles in the desired color.

When working with scissors, it is advisable to use cotton gloves, since you will have to cut a lot of plastic, and calluses may appear on your fingers.

leaf assembly

It is better to assemble leaves from bottles of close diameter. So it will be more beautiful. How larger size bottles, the more magnificent and longer the leaves are.
The sheet consists of identical elements. Each element is obtained by removing the bottom of the bottle and cutting the remaining part of the longitudinal strips towards the neck.
Next, we connect the elements, successively stringing them onto a rope or wire. We install lids on the first and last bottles, for which the rope will be fixed with knots. The sheet is ready.
To form a beautiful crown, it is desirable to use at least 5 such leaves.

Barrel assembly

The barrel is made from brown bottles by cutting longitudinal strips of equal width towards the neck. Only the hard bottom of the bottle remains unused.
The trunk gathers like leaves. However, for the vertical fixation of a palm tree, a rigid core is required, which is made of a metal or plastic tube. We put the details of the trunk on the tube.
The connection of leaves with the trunk and the formation of the final appearance
The leaves are attached to the trunk with glue or tape, forming lush crown. It is necessary to ensure that the leaves are evenly distributed around the trunk.

The palm tree from the bottles turns out to be quite heavy, so for its stability it is desirable to make the base in the form of a platform.

Or you can simply bury the base of the trunk about 50 cm into the ground. In the latter case, when assembling the trunk, you need to take a tube 50 cm longer than the palm tree.

Assembly instructions for a small palm tree

The above method of making a palm tree from plastic bottles is suitable for medium-sized palm trees. A small palm tree is best made using the following method.

leaf making

Remove the neck and bottom of the bottle
We cut the bottle into three identical petals towards the top and round off their ends.
We bend the petals in different directions and make cuts on them in increments of approximately 1 cm, not reaching the middle part
We bend the resulting strips through one at an angle of 40-60 degrees to give splendor

Such sheets to obtain a beautiful crown require about 3-5 pieces. The leaves are put on a rod protruding from the top of the trunk. The upper branch is fixed with tape or glue.

Barrel manufacturing

Take the bottom half of the bottle
On it we cut 6-8 identical petals or triangles
We drill a hole in the central part of the bottom of the bottle with a diameter slightly larger than the diameter of the rod
We put the resulting parts on the rod, having previously unbent the petals.

The trunk for a small palm tree is ready. In our gallery, as a visual aid, photographs of a palm tree from bottles are presented.

In this article, we have given you two instructions on how to assemble a beautiful palm tree from plastic bottles with your own hands. The first to assemble a medium-sized palm tree, the second to assemble a small palm tree. However, in the process of work, you can experiment and perhaps come up with new way manufacturing of plastic palm. We wish you good luck and hope that you will get the most beautiful palm tree!

Photo of a palm tree from bottles

Note!