GOST 11214 65 for public buildings. State standard of the union of the USSR. Types, sizes and brands

STATE STANDARD OF THE UNION OF SSR

WINDOWS AND BALCONY DOORS WOODEN WITH DOUBLE
GLAZING FOR RESIDENTIAL AND PUBLIC BUILDINGS

Types, design and dimensions

GOST 11214-86

State Construction Committee of the USSR

Moscow - 1986

INFORMATION DATA

DEVELOPED by the State Committee for Civil Engineering and Architecture under the USSR Gosstroy PERFORMERS IV Strokov (theme leader); B. A. Filozofovich; I. S. Poselskaya; G.G. Kovalenko; N.N. Tsaplev, Cand. tech. sciences; A. V. Tkachenko; G. V. Levushkin; N.V. Shvedov INTRODUCED by the State Committee for Civil Engineering and Architecture under the USSR Gosstroy Zam. Chairman M.P. Kokhanenko APPROVED AND PUT INTO EFFECT by decree State Committee USSR for construction of 11/14/85 No. 191

STATE STANDARD OF THE UNION OF SSR

WINDOWS AND BALCONY DOORS WOODEN WITH DOUBLE
GLAZING FOR RESIDENTIAL AND PUBLIC BUILDINGS

Types, design and dimensions

Wooden windows and balcony doors of double
glazing for dwelling and public buildings.
Types, structure and dimensions

GOST
11214-86

Instead of
GOST 11214-78

By the decree of the State Committee of the USSR for Construction Affairs dated November 14, 1985 No. 191, the introduction period was established

from 01.01.87

This standard applies to wooden windows and balcony doors with double glazing intended for residential and public buildings, as well as for auxiliary buildings and premises of enterprises various industries National economy.

1. TYPES, SIZES AND BRANDS

1.1. Windows and balcony doors manufactured according to this standard are divided into types: C - with paired sashes and door leaves; R - with separate doors and door leaves. 1.2. Overall dimensions of windows, balcony doors and the dimensions of the openings for them must correspond: for residential buildings - indicated in the devil. 1 and Appendix 1; for public buildings - indicated in the devil. 2 and Appendix 2. Windows and balcony doors, shown in the drawing. 1, can also be used for public buildings. 1.3. Windows sizes 9-13.5; 12-13.5; 15-13.5; 18-13.5 and 21-13.5 modules (module M-100 mm) for filling openings in walls from non-modular facing brick, at the request of the consumer, it is allowed to make 80 mm wider than indicated, by increasing the wide sashes, and the window with dimensions 15-6 modules - 70 mm wide less than the specified one, while the marking is changed accordingly by 9-14; 12-14; 15-14; 18-14; 21-14 and 15-5. 1.4. For residential buildings erected in IV climatic region, it is allowed to use windows with a narrow sash (without a vent). 1.5. At the request of consumers, single-leaf windows and balcony doors, incl. with vents and transoms should also be made with left-hand ones, and multi-sash windows with an asymmetric pattern - in a negative image. 1.6. Establish the following structure symbol(brands) of windows and balcony doors:

At the end of the brand of single-glazed windows and balcony doors, before the designation of the standard, add the number 1 through a dash. An example of a symbol for a window of type C for an opening with a height of 15 and a width of 9 dm, with a right-hand hinge of the sashes:

OS 15-9 GOST 11214-86

The same, with the left-hand hinge of the sashes:

OS 15-9L GOST 11214-86

Right balcony door type C for an opening 22 dm high and 9 dm wide:

BS 22-9 GOST 11214-86

The same, type P window for an opening with a height of 18 and a width of 18 dm, with an asymmetrical window pattern (option B):

OR 18-18V GOST 11214-86

The same in the negative image:

OR 18-18VN GOST 11214-86

The same, type C windows for an opening with a height of 15 and a width of 13.5 dm, with a window sash:

OS 15-13.5 GOST 11214-86

The same, for the right balcony door type C for an opening with a height of 22 and a width of 7.5 dm with a right hinge of the leaf:

BS 22-7.5 GOST 11214-86

The same, for the left balcony door:

BS 22-7.5L GOST 11214-86

2. DESIGN REQUIREMENTS

2.1. Windows and balcony doors must be manufactured in accordance with the requirements of GOST 23166-78, the requirements of this standard and according to working drawings approved in the prescribed manner. 2.2. The design, shape, main dimensions and brands of type C windows and balcony doors for residential buildings must correspond to those indicated in Fig. 3-5, for public buildings - hell. 6-11, and the dimensions of the cross-sections of parts and porches are in devil. 12-23. 2.3. The design, shape, main dimensions and brands of windows and balcony doors of type P for residential buildings must correspond to those indicated in Fig. 24-27, for public buildings - hell. 37-43, and the dimensions of the sections of parts and porches for residential buildings - to hell. 28-36, public buildings - to hell. 44-53. 2.4. Dimensions in general views of windows and balcony doors are given in the light on the outer sides of sashes, transoms, vents, door leaves and on the outer sides of boxes. In the drawings given in this standard, the dimensions of unpainted parts and products are indicated in millimeters. 2.5. To drain rainwater in the lower bars of boxes and in horizontal imposts of windows and balcony doors of type C, slots are made 12 mm wide, and holes with a diameter of 10 mm are drilled in windows and balcony doors of type P, located under wide sashes, canvases of balcony doors and transoms at a distance 50 mm from the vertical bars of boxes and imposts, and under the vents and narrow doors - one slot or one hole in the middle. 2.6. External sashes of windows and balcony door leaves of type P must be hung on mortise hinges with removable rods in accordance with GOST 5088. Internal sashes of type C windows with a height of more than 1400 mm and a width of more than 600 mm, as well as a height of more than 1000 mm and a width of more than 900 mm must be hung on 3 loops. 2.7. For glazing windows and balcony doors of residential buildings, glass with a thickness of 2.5-3 mm in accordance with GOST 111-78 should be used, and for public buildings 3-4 mm thick. The thickness of the glass is specified in the project and when ordering products, taking into account wind loads and noise effects in the construction area. 2.8. The locations of the sealing polyurethane foam gaskets in accordance with GOST 10174-72 in the vestibules of windows and balcony doors are indicated on the sectional drawings. 2.9. At the request of consumers along the perimeter of window and door frames on the end and side surfaces, it is allowed to arrange longitudinal grooves of various profiles, filled with inserts and framed by platbands when the blocks are connected to each other. 2.10. In residential and public buildings for climatic regions, where, according to thermal engineering calculations, windows and balcony doors with double glazing are not required, as well as in unheated buildings and premises, only external elements of windows and balcony doors of type P should be used, while the thickness of the box bar should not be less than 54 mm, and the dimensions of the sections are set in the working drawings. 2.11. To ensure the possibility of equipping windows and balcony doors of public buildings with lever-type fanlight devices, it is allowed to increase the thickness of the upper and vertical bars of boxes and imposts by 20 mm without changing the dimensions of the products. 2.12. By agreement between the manufacturer and the consumer, it is allowed to manufacture balcony doors with a height of 28 modules with transoms in separate boxes. In this case, the height of the blind part of the canvases or the glazed part of the transom is reduced by 50 mm. 2.13. By agreement between the manufacturer and the consumer, it is allowed to manufacture type C windows with a height of 6 and 9 modules, intended for stairwells, without impost with a sash hinge on the lower horizontal axis with the obligatory installation of opening stops. 2.14. By agreement between the manufacturer and the consumer, it is allowed to fill the blank part of the inner sheets of balcony doors of types C and P with cement particle boards in accordance with GOST 26816-86 separately or with fiber boards, and in the outer sheets it is possible to replace wood paneling cement particle boards 12 mm thick. Other options for filling the blind part of the outer canvases are allowed, which do not reduce the operational characteristics of the products, while the filling (panel) should be deepened in quarters of the bars and secured with a layout (glazing bead). 2.15. The arrangement of devices in windows and balcony doors (examples) is given in the recommended appendix 3; glass specifications for windows and balcony doors for residential buildings are given in reference annex 4, glass specifications for windows and balcony doors for public buildings are given in reference annex 5.

Overall dimensions of windows and balcony doors of types C and P of residential buildings

Crap. one

Overall dimensions of windows and balcony doors of types C and P of public buildings

Crap. 2 Notes to fig. 1 and 2: 1. Product diagrams are shown from the side of the facade. 2. The numbers above the product diagrams indicate the dimensions of the openings in the modules. 3. Windows of residential buildings with a height of 18 modules and balcony doors with a height of 24 modules - of limited use for climatic subdistricts 1A, 1B and 1G.

Construction, shape, main dimensions and brands of windows and balcony doors of residential buildings

Sections along the narthexes of windows and balcony doors of residential and public buildings

1 - sealing gaskets; 2 - loop (for side section)

Notes: 1. The grooves in the hinge mounting locations for pairing the sashes are not shown conventionally. 2. The dimensions of the glazing bead may be reduced to 14 ´ 9 mm. 3. The profile of the flaps in the inter-glass space is allowed to be made without a slope (bevel).

1 - sealing gaskets; 2 - slot for water drainage 12 mm wide

Notes: 1.К 1 - cross-sectional profiles of boxes; 1 (in a circle) - sash cross-sectional profiles. 2. The width of the upper protrusion of the lower bar of the box may be reduced by 2 mm. 3. The thickness of the lower bar of the box may be increased by 3 mm with a corresponding increase in the height of the box.

Note: It is allowed to undercut the profile of the impost in the vestibule with a depth of up to 2 mm.

Note: Hinge for hinging the wide sash of three-winged windows.

1 - 12 mm thick soft fiberboard GOST 4598-74; 2 - solid fibreboard of grade T of group A with a thickness of 3.2-4 mm in accordance with GOST 4598-74; 3 - polished fibreboard 16 mm thick in accordance with GOST 10632-77; 4 - glassine in accordance with GOST 2697-83; 5 - cladding of type O-2 in accordance with GOST 8242-75; 6 - layout; 7 - sealing gasket

1 - cover strip

Type P
Construction, shape, main dimensions and brands of windows and balcony doors of residential buildings

Note: The height of the inner pane flaps may be increased by 5 mm due to the corresponding decrease in the height of the pane flaps.

Sections along the narthexes of windows and balcony doors of residential buildings

1 - sealing gasket

Notes: 1. It is allowed to reduce the glazing bead size to 14 ´9 mm. 2. The thickness of the bars of the inner box (except for the lower ones) may be reduced by 5 mm with a corresponding change in the dimensions of the box. 3. The width of the groove in the bars of the outer box may be reduced to 8 mm.

1 - slot for water drainage 12 mm wide

1 - soft fibreboard 12 mm thick in accordance with GOST 4598-86; 2 - solid fibreboard of grade T of group A with a thickness of 3.2-4 mm in accordance with GOST 4598-86; 3 - polished chipboard 16 mm thick in accordance with GOST 10632-89; 4 - glassine in accordance with GOST 2697-83; 5 - cladding of type O-2 in accordance with GOST 8242-88; 6 - layout

Construction, shape, main dimensions and brands of windows and balcony doors of public buildings

Sections along the narthexes of windows and balcony doors of public buildings

Note. It is allowed to reduce the size of the glazing bead by 1 mm.

1 - sealing gasket

1 - hole with a diameter of 10 mm for water drainage

Note. Loop for section B5.

Note. Filling the canvases and the option of filling the blank part of the inner leaf, see fig. 50.

1 - soft fibreboard 12 mm thick in accordance with GOST 4598-86; 2 - solid fibreboard of grade T of group "A" with a thickness of 3.2-4 mm in accordance with GOST 4598-86; 3 - polished chipboard 16 mm thick in accordance with GOST 10632-89; 4 - glassine in accordance with GOST 269783; 5 - cladding of type O-2 in accordance with GOST 8242; 6 - layout

1 - cover strip

ANNEX 1
Reference

DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF RESIDENTIAL BUILDINGS

APPENDIX 2
Reference

DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF PUBLIC BUILDINGS

Note. The dimensions of the opening widths are indicated for walls made of panels and modular bricks.

LOCATION OF APPLIANCES IN WINDOWS AND BALCONY DOORS
(examples)

1 - hinge PV1-100 for internal doors and canvases of types C and P; 2 - hinge PV2-100-1 for external doors and canvases of type P; 3 - loop PV3-1 for type C; 4 - coupler CT for type C; 5 - stop UO for type P; 6 - wrapping ZR2-1

1 - hinge PV1-100 for internal doors and canvases of types C and P; 2 - hinge PV2-100-1 for external doors and canvases of type P; 3 - loop PV3-1 for type C; 4 - loop PV2-100-2 for transom; 5 - fanlight device PF2; 6 - latch FK1 for type C or FK3 for type P; 7 wrapping ZR2-1; 8 - coupler CT for type C; 9 - stop UO for type P; 10 - PC80 handle.

Notes to hell. 1 and 21. Appliances for windows and balcony doors must comply with GOST 538-78, GOST 5087-80, GOST 5088, GOST 5090-79 and GOST 5091-78.2. Outside sashes should be hung on hinges of type PV2 with removable rods. 3. The wraps are shown in the open position. 4. PC80 handles are installed on external doors with outside buildings at a height of 1000 mm from the threshold. 5. The fanlight device is shown conventionally. 6. The squares are installed in accordance with clause 2.13 of GOST 23166-78.7. CT screeds are placed on the shutters from the side of the room. 8. Retainers are installed on narrow window sashes of residential and public buildings. 9. In the case of using wraps with removable handles of the P2 type, the number of handles per product is set by agreement between the manufacturer and the consumer, but not less than one.

APPENDIX 4
Reference

SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF RESIDENTIAL BUILDINGS

Dimensions, mm

Quantity

OS 6-9

OS 6-12

OS 9-9

OS 9-12

OS 12-9

OS 12-12

OS 15-6

OS 15-9

OS 15-12

OS 15-9A

OS 9-13.5

OS 9-15

OS 12-13.5

BS 22-7.5

BS 24-7.5

OS 12-15

OS 15-13.5

OS 15-15

OS 15-18

OS 15-21

OS 18-9

OS 18-13.5

OS 18-15

OS 18-9A

BS 22-9

BS 24-9

Dimensions, mm

internal

outdoor

Quantity

OR 6-9

OR 6-12

OR 9-9

700

OR 9-12

OR 12-9

OR 12-12

OR 15-6

OR 15-9

OR 15-12

OR 9- 13.5

OR 9-15

OR 12 -13.5

OR 12-15

OR 15-9A

OR 15-13.5

OR 15-15

OR 15-18

OR 15-21

OR 18-9A

OR 18-9

RR 18-13.5

OR 18-15

BR 22-7.5

BR 22-9

BR 24-7.5

BR 24-9

APPENDIX 5
Reference

SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF PUBLIC BUILDINGS

Dimensions, mm

Quantity

OS 12-9V

OS 12-12V

OS 12-13.5V

1145

OS 12-15V

OS 18-9V

1050 395

OS 18-12V

OS 18-13.5V

OS 18-15V

OS 18-9G

OS 18-12G

OS 18-13.5G

OS 18-15G

OS 12-18V

OS 12-21V

OS 18-18V

OS 18-21V

OS 18-24V

OS 18-18G

OS 18-21G

OS 18-24G

OS 21-21V

OS 21-24V

OS 21-21G

OS 21-24G

1030

OS 18-27V

OS 18-27G

OS 21-27V

OS 21-27G

OS 21-9V

OS 21-12V

OS 21-13.5V

OS 21-9G

OS 21-12G

OS 21-13.5G

OS 21-15V

OS 21-18V

OS 21-45G

OS 21-18G

BS 38-9

BS 28-12

BS 28-18

Type P

Dimensions, mm

Brand

internal

outdoor

Quantity

OR 12-9V

OR 12-12V

OR 12-13.5V

STATE STANDARD OF THE UNION OF SSR

TYPES, DESIGN AND DIMENSIONS

GOST 11214-78

Official edition

udk muimi s hum

STATE

STANDARD

Group N02 SSR

WOODEN WINDOWS AND BALCONY DOORS WITH DOUBLE GLAZING FOR RESIDENTIAL AND PUBLIC BUILDINGS

Types, design and dimensions

Wooden windows and balcony doors of double glazing for dwelling and public buildings. Types construction and dimensions

Instead of GOST 11214-61

By the decree of the State Committee of the USSR for Construction Affairs dated December 13, 1V7B, I * 230, the introduction period was established from 01.01.1681.

Failure to comply with the standard is punishable by law

This standard applies to wooden windows and double-glazed balcony doors intended for residential and public buildings, as well as for auxiliary buildings and premises of enterprises in various sectors of the national economy.

1. TYPES, SIZES AND BRANDS

1.1. Windows and balcony doors manufactured according to this standard are divided into two series:

C - with paired bindings and door leaves;

R - with separate bindings and door leaves.

1.2. Types and dimensions windows and balcony doors and the dimensions of the openings for them must correspond to:

for residential buildings - indicated in the devil. 1 and in reference annex 1;

for public buildings - indicated in the devil. 2 and in reference annex 2.

Windows and balcony doors, shown in devil. 1 can also be used for public buildings.

1.3. Windows with sizes 12-13.5; 15-13.5 and 18-13.5 modules (module M = 100 mm) for filling openings in walls from non-modular bricks of the facing masonry should be made 80 mm wider than indicated, by increasing the width of the wide sashes, and a window with dimensions of 15 6 modules with a width of 70 mm less than the specified one, while the marking changes accordingly by 12-14; 15-14; 18-14 and 15-5.

1.4. For residential buildings erected in climatic region IV, it is allowed to use windows with a narrow sash (without a vent).

1.5. At the request of consumers, single-leaf windows and balcony doors, including those with vents and transoms, must also be made left-handed, and multi-leaf windows with an asymmetric pattern must be made in a negative (mirror) image.

1.6. The following structure of the symbol (brand) of windows and balcony doors is established.

Ichemi official

Reprinted October, 1981

Reprinting prohibited

P. 10 GOST<1214-78

Construction, shape, main dimensions and brands of windows and balcony doors of public buildings

0S1V-9V OS1v-G2V OS 18-13.5 V OS 18-15 V 0S18-18V

0S18-9G OS18-12G 0S18 ~ 73.5G

OS 18-15 G OS 18-18 G

■ Product type:

B - balcony door ■ Product series:

C - with paired bindings and door leaves; R - with separate bindings and door leaves.

■ The size of the opening in height in dm.

■ The size of the opening in width in dm.

■ Letters meaning:

A, B, D, D, E - variants of drawings of the same size;

Н -window in negative (mirrored) design;

Л - left window or balcony door.

Designation of this standard.

At the end of the brand of single-glazed windows and balcony doors, the number 1 is added before the designation of the standard.

An example of a symbolic designation of a series C window for an opening with a height of 15 and a width of 9 dm, with a right-hand hinged sash:

OS 15-9 GOST 11214-78

The same, but with the left hinge of the sashes:

OS 15-9L GOST 11214-78

The same, for the right-hand balcony door of the C series for an opening with a height of 22 and a width of 9 dm;

BS 22-9 GOST 11214-78

The same, P series windows for an opening 18 dm high and 18 dm wide, with an asymmetrical window pattern (type B):

OR 18-18V GOST 11214-78 The same, in a negative (mirror) version:

OP 18-18VN GOST 11214-78

The same, C-series windows for an opening with a height of 15 and a width of 13.5 dm, with a window sash:

OS 15-13.5 GOST 11214-78

The same, for the right balcony door of the C series for an opening with a height of 22 and a weight of the leaf:

BS 22-7.5 GOST 11214-78

The same, for the left balcony door:

BS 22-7.5L GOST 11214-78

width 7.5 dm, from the right to

2. CONSTRUCTION CONCERNS

2.2. The design, shape, main dimensions and brands of windows and balcony doors serine C for residential buildings must correspond to those indicated in Fig. 3-6, for public buildings - hell. 7-11, and the dimensions of the cross-sections of parts and porches are in the devil. 12-22.

GOST m<4-78 Стр. 3

2.3. The design, shape, main dimensions and brands of windows and balcony doors of the P series for residential buildings must correspond to those indicated in Fig. 23-26, for public buildings - hell. 27-31, and the dimensions of the sections of parts and porches for residential buildings are to hell. 32-40, public buildings - to hell. 41 -50.

2.4. Dimensions in general views of windows and balcony doors are given in the light, on the outer sides of sashes, transoms, vents and door leaves and on the outer sides of the boxes.

In the drawings given in this standard, the dimensions of unpainted parts and products are indicated in mm.

2.5. For drainage of rainwater in the lower bars of the boxes and in horizontal imposts under wide sashes, transoms and canvases, slots 12 mm wide are made, located at a distance of 50 mm from the vertical bars of the boxes and imposts, and under the vents there is one slot in the middle of the window.

2.6. Sashes and canvases of P series windows and balcony doors must be hung on mortise hinges with removable rods in accordance with GOST 5088-78 and GOST 17585-72.

Sashes of C series windows with a height of more than 1400 mm and a width of more than 600 mm, as well as a height of more than 1000 mm and a width of more than 900 mm must be hung on 3 hinges.

Examples of the arrangement of devices in windows and balcony doors are given in the recommended appendix 3.

2.7. For glazing windows and balcony doors of residential buildings, glass with a thickness of 2.5-3 mm in accordance with GOST 111-78 should be used, and for public buildings 3-4 mm thick.

The thickness of the glass is specified in the project and when ordering products, taking into account wind loads and noise effects in the construction area.

2.8. The installation locations of the gaskets in the porches of windows and balcony doors are shown in the sectional drawings.

2.9. Along the perimeter of window and door frames on the end and side surfaces, it is allowed at the request of consumers, the device of longitudinal grooves of various profiles, filled with inserts and framed by platbands when connecting the blocks to each other.

2.10. In residential and public buildings for climatic regions where, according to thermal engineering calculations, windows and balcony doors with double glazing are not required, as well as in unheated buildings and premises, only the outer parts of windows and balcony doors of the P series should be used, while for residential buildings the thickness of the box bar increases to 54 mm.

2.11. To ensure the possibility of equipping windows and balcony doors of public buildings with lever-type fanlight devices, it is allowed to increase the thickness of the upper and vertical bars of boxes and imposts by 20 mm, without changing the dimensions of the products.

2.12. The appendices to this standard contain:

the dimensions of the openings of windows and balcony doors in the outer walls of residential buildings - in reference annex 1;

the dimensions of window openings and balcony doors in the outer walls of public buildings - in reference annex 2;

arrangement of devices in windows and balcony doors (examples) - in the recommended appendix 3;

glass specification for windows and balcony doors for residential buildings - in reference annex 4;

glass specification for windows and balcony doors in public buildings - in reference annex 5.

Types and dimensions of windows and balcony doors of the C and P series of residential buildings

B AP OTHER DOORS

Notes:

1. Product diagrams are shown from the side of the facade.

2. The numbers above the product diagrams indicate the dimensions of the openings in the modules.

GOST 11114-78 pp. 5

Types and dimensions of windows and balcony doors of the C and P series of public buildings

18- 27G 18-27E

21 -27V 21-27D

BALCONY DOORS

See notes on fig. I.

Construction, shape, main dimensions and brands of windows and balcony doors of residential buildings

0012-7.5 OS 12-9

OC12r% 5A 0C1Z-3A

Section [-7

1Ш L L i * so L L nee L L nu L I. eso (. L sso

GOST 11214-78 pp. 7

0C1S-ZSA OS is-9A

D1 0S12-73.5 OS 12-15

Page 8 GOST 11114-78

GOST 11214-86

UDC 691.11.028.1:006.354 Group Ж32

STATE STANDARD OF THE UNION OF SSR

WINDOWS AND BALCONY DOORS WOODEN WITH DOUBLE

GLAZING FOR RESIDENTIAL AND PUBLIC BUILDINGS

Types, design and dimensions

Wooden windows and balcony doors of double glazing

for dwelling and public buildings.

Types, structure and dimensions

OKP 53 6131, 53 6132

Date of introduction 1987-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the USSR State Construction Committee

DEVELOPERS

IVStrokov (topic leader); B.A. Filozofovich; I.S. Poselskaya; G.G. Kovalenko; N.N. Tsaplev, Cand. tech. sciences; A.V. Tkachenko; G.V. Levushkin; N.V. Shvedov

2. APPROVED AND INTRODUCED INTO EFFECT by the resolution of the USSR State Committee for Construction Affairs of 11/14/85 N 191

3. REPLACE GOST 11214-78

4. REFERENCE REGULATORY AND TECHNICAL DOCUMENTS

	Item number, application		Item number, application
		GOST 5091-78	Appendix 3
	Appendix 3	GOST 8242-88
GOST 2697-83		GOST 10174-90
GOST 4598-86		GOST 10632-89
GOST 5087-80	Appendix 3	GOST 23166-78	2.1, appendix 3
GOST 5088-94	2.6, appendix 3	GOST 26816-86
GOST 5090-86	Appendix 3

5. REDISSION

1. TYPES, SIZES AND BRANDS

1.1. Windows and balcony doors manufactured according to this standard are subdivided into types: C - with twin sashes and door leaves; R - with separate doors and door leaves.

1.2. The overall dimensions of windows, balcony doors and the dimensions of the openings for them must correspond to: for residential buildings - those indicated in Fig. 1 and in Appendix 1; for public buildings - indicated in Fig. 2 and in Appendix 2. Windows and balcony doors shown in Fig. 1 may also be used for public buildings.

1.3. Windows sizes 9-13.5; 12-13.5; 15-13.5; 18-13.5 and 21-13.5 modules (module M = 100 mm) for filling openings in walls from non-modular facing brick, at the request of the consumer, it is allowed to make 80 mm wider than indicated, by increasing the wide sashes, and the window with dimensions 15-6 modules - 70 mm wide less than the specified one, while the marking is changed accordingly by 9-14; 12-14; 15-14; 18-14; 21-14 and 15-5.

1.4. For residential buildings erected in climatic region IV, it is allowed to use windows with a narrow sash (without a vent).

1.5. At the request of consumers, single-leaf windows and balcony doors, incl. with vents and transoms should also be made with left-hand ones, and multi-sash windows with an asymmetric pattern - in a negative image.

1.6. Establish the following structure of the symbol (brand) of windows and balcony doors:

At the end of the brand of single-glazed windows and balcony doors, before the designation of the standard, add the number 1 through a dash.

Legend examples

Window type C for an opening with a height of 15 and a width of 9 dm, with a right-hand hinge of the sashes: OS15-9 GOST 11214-86

The same, with the left hinge of the shutters: OS15-9L GOST 11214-86

Right balcony door type C for an opening with a height of 22 and a width of 9 dm: BS22-9 GOST 11214-86

P-type window for an opening with a height of 18 and a width of 18 dm, with an asymmetrical window pattern (option B):

OR18-18V GOST 11214-86

The same, in a negative image: OR18-18VN GOST 11214-86

Window type C for an opening with a height of 15 and a width of 13.5 dm, with a window sash:

OS15-13.5 GOST 11214-86

Right balcony door type C for an opening with a height of 22 and a width of 7.5 dm: BS22-7.5 GOST 11214-86

The same, left: BS22-7.5L GOST 11214-86

2. DESIGN REQUIREMENTS

2.1. Windows and balcony doors must be manufactured in accordance with the requirements of GOST 23166 and this standard according to working drawings approved in the prescribed manner.

2.2. and balcony doors of type C for residential buildings should correspond to those indicated in drawing 3-5, for public buildings in drawing 6-11, and the dimensions of the sections of parts and porches - in drawing 12-23.

2.3. The design, shape, main dimensions and brands of windows and balcony doors of type P for residential buildings must correspond to those indicated in Fig. 24-27, for public buildings - in Fig. 37-43, and the dimensions of the sections of parts and porches for residential buildings - in Fig. .28-36, public buildings - in drawing 44-53.

2.4. Dimensions in general views of windows and balcony doors are given in the light on the outer sides of sashes, transoms, vents, door leaves and on the outer sides of boxes.

In the drawings given in this standard, the dimensions of unpainted parts and products are indicated in millimeters.

2.5. To drain rainwater in the lower bars of boxes and in horizontal imposts of windows and balcony doors of type C, slots are made 12 mm wide, and holes with a diameter of 10 mm are drilled in windows and balcony doors of type P, located under wide sashes, canvases of balcony doors and transoms at a distance 50 mm from the vertical bars of boxes and imposts, and under the vents and narrow doors - one slot or one hole in the middle.

2.6. External sashes of windows and balcony door leaves of type P must be hung on mortise hinges with removable rods in accordance with GOST 5088. Internal sashes of type C windows with a height of more than 1400 mm and a width of more than 600 mm, as well as a height of more than 1000 mm and a width of more than 900 mm must be hung on three loops.

2.7. For the glazing of windows and balcony doors of residential buildings, glass with a thickness of 2.5-3 mm in accordance with GOST 111 should be used, and for public buildings 3-4 mm thick.

The thickness of the glass is specified in the project and when ordering products, taking into account wind loads and noise effects in the construction area.

2.8. The locations of the sealing polyurethane foam gaskets in accordance with GOST 10174 in the vestibules of windows and balcony doors are indicated on the sectional drawings.

2.9. At the request of consumers, along the perimeter of window and door frames on the end and side surfaces, it is allowed to arrange longitudinal grooves of various profiles, filled with inserts and framed by platbands when the blocks are connected to each other.

2.10. In residential and public buildings for climatic regions, where, according to thermal engineering calculations, windows and balcony doors with double glazing are not required, as well as in unheated buildings and premises, only external elements of windows and balcony doors of type P should be used, while the thickness of the box bar should not be less than 54 mm, and the dimensions of the sections are set in the working drawings.

2.11. To ensure the possibility of equipping windows with lever-type fanlight devices, it is allowed to increase the thickness of the upper and vertical bars of boxes and imposts by 20 mm without changing the dimensions of the products.

2.12. By agreement between the manufacturer and the consumer, it is allowed to manufacture balcony doors with a height of 28 modules with transoms in separate boxes. In this case, the height of the blind part of the canvases or the glazed part of the transom is reduced by 50 mm.

2.13. By agreement between the manufacturer and the consumer, it is allowed to manufacture type C windows with a height of 6 and 9 modules, intended for staircases, without impost with a sash hinge on the lower horizontal axis with the mandatory installation of opening stops.

2.14. By agreement between the manufacturer and the consumer, it is allowed to fill the blind part of the inner panels of balcony doors of types C and R with CBPB in accordance with GOST 26816 separately or with fiberboard, and in the outer panels, replacement of wood sheathing with CBPB with a thickness of 12 mm is allowed. Other options for filling the blind part of the outer canvases are allowed, which do not reduce the operational characteristics of the products, while the filling (panel) should be deepened in quarters of the bars and secured with a layout (glazing bead).

2.15. The arrangement of devices in windows and balcony doors (examples) is given in Appendix 3; the specification of glasses for windows and balcony doors of residential buildings is given in Appendix 4, and the specification of glasses for windows and balcony doors of public buildings is in Appendix 5.

types C and P residential buildings

Overall dimensions of windows and balcony doors

types C and P public buildings

Notes to Fig. 1 and 2:

1. Product diagrams are shown from the side of the facade.

2. The numbers above the product diagrams indicate the dimensions of the openings in the modules.

3. Windows of residential buildings with a height of 18 modules and balcony doors with a height of 24 modules - of limited use for climatic subdistricts 1A, 1B and 1G.

Construction, shape, main dimensions and brands of windows

and balcony doors of residential buildings

Construction, shape, main dimensions and brands of windows

and balcony doors of public buildings

residential and public buildings

1 - sealing gaskets; 2 - loop (for side section)

Notes:

1. The grooves in the places where the hinges are mounted for pairing the shutters are not shown conventionally.

2. The dimensions of the glazing bead may be reduced to 14x9 mm.

3. The profile of the flaps in the inter-glass space is allowed to be made without a slope (bevel).

1 - sealing gaskets; 2 - slot for water drainage 12 mm wide

Notes:

1 TO 1 - cross-sectional profiles of boxes; 1 (in a circle) - sash cross-sectional profiles.

2. The width of the upper protrusion of the lower bar of the box may be reduced by 2 mm.

3. The thickness of the lower bar of the box may be increased by 3 mm with a corresponding increase in the height of the box.

(Revised, 1988 Amendment)

Note: It is allowed to undercut the profile of the impost in the vestibule with a depth of up to 2 mm.

(Revised, 1988 Amendment)

Damn 16 Damn 17

Note: Hinge for hinging the wide sash of three-winged windows.

Damn. 18 Damn. 19

; 7 - sealing gasket

Damn 20 Damn 21

1 - cover strip

Damn. 22 Damn. 23

Note: The height of the inner pane flaps may be increased by 5 mm due to the corresponding decrease in the height of the pane flaps.

(Modified edition, Amendment 1988)

1 - sealing gasket

Notes:

1. It is allowed to reduce the size of the glazing bead to 14x9 mm.

2. The thickness of the bars of the inner box (except for the lower ones) may be reduced by 5 mm with a corresponding change in the dimensions of the box.

3. The width of the groove in the bars of the outer box may be reduced to 8 mm.

1 - slot for water drainage 12 mm wide

1 - soft fiberboard 12 mm thick in accordance with GOST 4598; 2 - solid fiberboard of grade T of group A with a thickness of 3.2-4 mm in accordance with GOST 4598; 3 - polished chipboard 16 mm thick in accordance with GOST 10632; 4 - glassine in accordance with GOST 2697; 5 - cladding of type O-2 in accordance with GOST 8242; 6 - layout

Damn. 35 Damn. 36

Construction, shape, main dimensions and brands of windows

and balcony doors of public buildings

Sections along the narthexes of windows and balcony doors

public buildings

Note. It is allowed to reduce the size of the glazing bead by 1 mm.

1 - sealing gasket

1 - hole with a diameter of 10 mm for water drainage

Damn. 45 Damn. 46

Note. Loop for section B5.

Note. Filling the canvases and the option of filling the blank part of the inner leaf, see drawing 50.

1 - cover strip

Damn 52 Damn 53

ANNEX 1

Reference

DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF RESIDENTIAL BUILDINGS

APPENDIX 2

Reference

DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF PUBLIC BUILDINGS

Note. The dimensions of the opening widths are indicated for walls made of panels and modular bricks.

LOCATION OF APPLIANCES IN WINDOWS AND BALCONY DOORS

(examples)

1 - hinge PV1-100 for internal doors and canvases of types C and P; 2 - hinge PV2-100-1 for external doors and canvases of type P; 3 - loop PV3-1 for type C; 4 - loop PV2-100-2 for transom; 5 - fanlight device PF2; 6 - latch FK1 for type C or FK3 for type P; 7 - wrapping ZR2-1; 8 - coupler CT for type C; 9 - stop UO for type P; 10 - PC80 handle.

Notes to Fig. 1 and 2

1. Devices for windows and balcony doors must comply with GOST 538, GOST 5087, GOST 5088, GOST 5090 and GOST 5091.

2. Outside sashes should be hung on hinges of type PV2 with removable rods.

3. The wraps are shown in the open position.

4. PC80 handles are installed on the outer doors on the outside of the building at a height of 1000 mm from the threshold.

5. The fanlight device is shown conditionally.

6. Squares are installed in accordance with clause 2.13 of GOST 23166.

7. CT screeds are placed on the shutters from the side of the room.

8. Retainers are installed on narrow window sashes of residential and public buildings.

9. In the case of using wraps with removable handles of the P2 type, the number of handles per product is set by agreement between the manufacturer and the consumer, but not less than one.

(Modified edition, Amendment 1988)

APPENDIX 4

Reference

SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF RESIDENTIAL BUILDINGS


	Size, mm					Size, mm

Size, mm

interior

outer

interior

outer

APPENDIX 5

Reference

SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF PUBLIC BUILDINGS


	Size, mm					Size, mm

Size, mm

interior

outer

interior

outer

one . TYPES, SIZES AND BRANDS

2. DESIGN REQUIREMENTS

Overall dimensions of windows and balcony doors of types C and P of residential buildings

Overall dimensions of windows and balcony doors of types C and P of public buildings

Construction, shape, main dimensions and brands of windows and balcony doors of residential buildings

Sections along the narthexes of windows and balcony doors of residential and public buildings

Damn 16, Damn 17

Damn 18, Damn 19

Damn 20, Damn 21

Damn 22, Damn 23

Construction, shape, main dimensions and brands of windows and balcony doors of residential buildings

Sections along the narthexes of windows and balcony doors of residential buildings

Damn 35, Damn 36

Construction, shape, main dimensions and brands of windows and balcony doors of public buildings

Sections along the narthexes of windows and balcony doors of public buildings

Crap. 45, Damn. 46

Crap. 52, Damn. 53

APPENDIX 1 (reference). DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF RESIDENTIAL BUILDINGS

APPENDIX 2 (reference). DIMENSIONS OF WINDOW AND BALCONY DOOR OPENINGS IN THE EXTERNAL WALLS OF PUBLIC BUILDINGS

Damn 1 (continued)

APPENDIX 4 (reference). SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF RESIDENTIAL BUILDINGS

APPENDIX 5 (reference). SPECIFICATION OF GLASSES FOR WINDOWS AND BALCONY DOORS OF PUBLIC BUILDINGS

STATE STANDARD OF THE UNION OF SSR

TYPES, DESIGN AND DIMENSIONS

GOST 11214-78

Official edition

udk muimi s hum

STATE

STANDARD

Group N02 SSR

WOODEN WINDOWS AND BALCONY DOORS WITH DOUBLE GLAZING FOR RESIDENTIAL AND PUBLIC BUILDINGS

Types, design and dimensions

Wooden windows and balcony doors of double glazing for dwelling and public buildings. Types construction and dimensions

Instead of GOST 11214-61

By the decree of the State Committee of the USSR for Construction Affairs dated December 13, 1V7B, I * 230, the introduction period was established from 01.01.1681.

Failure to comply with the standard is punishable by law

1. TYPES, SIZES AND BRANDS

1.1. Windows and balcony doors manufactured according to this standard are divided into two series:

C - with paired bindings and door leaves;

R - with separate bindings and door leaves.

1.2. The types and overall dimensions of windows and balcony doors and the dimensions of the openings for them must correspond to:

for residential buildings - indicated in the devil. 1 and in reference annex 1;

for public buildings - indicated in the devil. 2 and in reference annex 2.

Windows and balcony doors, shown in devil. 1 can also be used for public buildings.

1.4. For residential buildings erected in climatic region IV, it is allowed to use windows with a narrow sash (without a vent).

1.6. The following structure of the symbol (brand) of windows and balcony doors is established.

Ichemi official

Reprinted October, 1981

Reprinting prohibited

P. 10 GOST<1214-78

Construction, shape, main dimensions and brands of windows and balcony doors of public buildings

0S1V-9V OS1v-G2V OS 18-13.5 V OS 18-15 V 0S18-18V

0S18-9G OS18-12G 0S18 ~ 73.5G

OS 18-15 G OS 18-18 G