What glue glue the mirror on the closet. Mechanical fastening method. Fastening process: Step-by-step instruction

There are mirrors in every home. Often they are embedded in furniture, for example, in the wardrobes or cabinets for the bathroom, but in some cases it is attached to the wall.

The easiest way, if the finished mirror is located in the frame, then it will not be built it. And if it is fixed to the wall, and even more so if the accessory is big, for example, from the floor to the ceiling, efforts will have to make up and, of course, high-quality

To hang or glue the mirror you need to carefully plan. When calculating dimensions, it is important to consider that the mirror should not touch other objects, otherwise cracks may later appear.

What glue glue the mirror

Tytan glue for mirrors

Glue for gluing mirrors Titan – one of the most reliable compositions for working with different surfaces.

It is made of resin and rubber, which ensure the reliability of fixation and installation of decorative mirrors to the tile, concrete, metal, wooden surfaces, drywall plates.

The main properties of the glue titanium:

elastic and waterproof seams
high adhesion to most surfaces,
does not damage the amalgam mirror,
easy to use
durable
no moisture is afraid
affordable price.

Tytan is applied to a dry smooth degreased surface with a pistol. Two centimeters retreat from the edge, and between the glue strips - five centimeters.

Within five minutes, the position of the mirror can be adjusted for several millimeters.

When working with large mirrors, it is worth purchasing fasteners that will protect from falling.

Alternative Titanium - Abro

Quick-frustrating and very durable ABRO glue is used for compounds, metal glass, glass glass.

The manufacturer delivers the composition in two ampoules. One contains glue, in another activator.

Since the composition includes amine acids and isopropanol, it is possible to use the tool only in a well-ventilated room.

Soudal (Mirror Glass)
Bostik 2750 is guaranteed not corrosive mirror amalgam.

How to glue the mirror to the wall

To attach the mirror to the wall, nails and hammer do not need. We use the "Moment Installation" glue. It does not damage the amalgam coating of the mirror, waterproof, suitable for internal work.

We also need:

mounting pistol,
stationery knife,
stool,
foam or other soft surface (we put the mirror during the applying of glue),
mirror.

Powing is performed only under the condition of dryness and walls, and the mirror itself.

Operating procedure:

Sut off the stationery knife with a tube with glue.
I turn over the mirror and put on the front side of the steady surface (for example, a stool), pre-laying the soft material under it.
Install the glue into the mounting gun and apply the composition on the mirror strips throughout its surface.
Click it to the wall and immediately tear off. We are waiting for 3-4 minutes. This technique allows you to speed up the gluing process. It can be used in working with all solvent-based mounting adhesives.
Apply the mirror to the wall again. Since it is heavy, we use to fix the "Moment of Super Tape". We stick a few stripes of ribbons along its surface, capturing the wall. After a day, the tape can be removed.

VIDEO INSTRUCTION

How to glue the mirror to the cabinet door

For what glue a mirror? Such a question arises from the owners of the cabinets, wished to attach it to the door.

The best result demonstrates the combination of silicone (or liquid nails) and bilateral scotch.

Also for work will be required:

glass washing means
pure rag,
4 strips Fiberboard width 2-4 cm and a little longer than more than minimum size mirrors.

The order of gluing:

Remove the door with loops and put on the floor or on the front surface of the face up.
We apply the mirror to the door and outline it around the perimeter. So we will make a place of gluing.
Wet the wind in the glass wash facility and wipe the door, then reverse side mirrors.
We glue the double-sided tape band with an indentation from each other at 20 cm. Scotch should not appear for applied markup.
Between the scotch strips we lay the BOB strips so that they do not touch each other. Silicone is applied to Silicone-free from Scotch and Fiberboard.
We remove the protective strips from the tape and apply the mirror.
On my own or attracting the assistant, hold it and get the strip of the Fiberboard. Watch that the mirror does not come. It is more convenient to start pulling out the fiberboard on the one hand and move in order.
Press it to silicone rake. We are convinced that it was fixed.
Install the cabinet door in place.

Glue mirror on tile glue

The question is how to glue the mirror on the tile glue, all who make repairs in the bathroom are asked.

Before starting work, you need to choose a place where the mirror will hang.
Next, it is carefully cleaned, removing the tile on the plot where the mirror will be.
At the next stage, this area is covered and leveled, then glued the lower row of the curb.
The adhesive composition is applied perpendicular to the curb to ensure that the connection is more durable. In thickness, it must coincide with the thickness of the tile, on average it is 6-10 mm. Plastic crosses will be helped to make seams, which are fixed between the seams and leave the composition to the complete pouring. Then the top row of the border is placed.
It is recommended to nail a bar from a tree to the wall, which will hold the upper border until the glue is completely dry.
Then the side tiles are placed, removing excess glue from the surface.
Now you can start mounting. Be sure to leave a small gap between the mirror and tiles.
The mirror is applied to the wall and tightly pressed. In this position it needs to keep about 15 minutes. After drying the adhesive composition, it is possible to start grouting seams.

If the subject is heavy, tiled glue Do not do, we need liquid nails or glue sealant for mirrors. But not everyone is suitable, some corrosive Amalgam, as a result of which stains and cloues appear on the surface.

The proven means are MultiFix liquid nails, as well as Penosil Premium MirrorFIX, which not only provide a strong elastic compound, but also resistant to moisture.

The moment comes when the usual situation is bored. I want to change something, update old interior, add some detail or make good repair. Optimal method Refresh the room, make it lighter, perhaps even increase the space - attach the mirror on the cabinet. You acquired new furnitureYou need to glue the mirror on the cabinet door, and do not know how to do it right, let's look at individual attachment methods.

The optimal way to update the room, make it lighter, perhaps even increase the space - to attach the mirror on the cabinet.

"Liquid nails" or silicone apply to surrounding parallel lines Through equal intervals.

How to glue the mirror to the closet? How to properly do this work? There are several ways to glue the mirror.

Method name	Features method
Mounting bilateral scotch.	This material needs to choose correctly. Scotch must be highly tracked - 3m, foamed, its thickness should be 0.8-2 mm (to compose irregularities). It is possible to work with it at temperatures from +10 to + 25 ° C. The indicators above or below will not give proper clutch with the surface. The ribbon consumption is 60 cm² per 1 kg of mass.
The use of "liquid nails" of a special adhesive or colorless construction silicone.	There are some nuances: it is better not to glue the mirror on "liquid nails" and other means having a characteristic smell. Substance in them can lead to the damage of amalgam. It is better to acquire special adhesives for the mirror - "Titan" (most reliable means), "Abro", "Soudal", "Bostik 2750". Very high quality and handy way - gluing the mirror on silicone. This is the best option.
Mechanical method.	Using P-shaped metal legs, plastic stops or special screws.

You purchased new furniture, you need to stick the mirror on the cabinet door, and do not know how to do it right, let's consider individual attachment methods.

Most optimal option - gluing the mirror on a building colorless silicone.

Attention! Which one is the option of gluing to choose, solve yourself. The main thing is not to hurry, to perform all the work to be scrupulously, to come to the matter responsibly, then the mirror will be attached quite firmly and serves a long time.

How to glue the mirror to the closet?

Remove the protective stickers from Scotch.

Necessary materials

Before you start work, you need to prepare the following materials: Mirror, "Liquid nails", glue or silicone for gluing mirrors, double-sided tape, greasy tape, degreasing agent.

There are several ways to glue the mirror.

Now you need to wait when the glue dries.

Required tools

From the tools will be useful: sandpaper, gun mount, pencil, line or roulette. If you fasten the mirror on the mount, then you need a drill, screwdriver, screwdriver, drills ordinary, diamond drill (to do a hole in the mirror), a special mount for mirrors.

Which one is the option of gluing to choose, solve yourself.

You decided not to use "liquid nails", but attach to the paws, then you need to make sure of their production accuracy in height and, if necessary, mount gaskets.

Fastening process: Step-by-step instruction

So, you got stuck with all materials and tools, acquired a mirror desired size. Preferably, if its back side is protected by a special film, which, if the mirror breaks, will prevent the springs of the fragments. Now proceed to work.

You can walk small emery paper For better grasp adhesive.

Before fastening the mirror, it is necessary to put a soft layer, then enhance the mirror with my paws.

First remove the cabinet door. To work back to work, you need to position it in a horizontal position. Pencil on the surface applied line markup. Clean the door degreasing means, then the mirror. You can walk in shallow sandpaper for better grasp adhesive. Tassel remove all dust.

Clean the door degreasing means, then the mirror.

If there are finished holes in the mirror, you can use special screws instead of foot.

"Liquid nails" or silicone apply to a mirror surface with parallel lines at an equal interval. Between them for auxiliary fastening glue bilateral scotch strips. The most optimal option is to glue the mirror on a building colorless silicone. You do not need to use only tape, since the mirror glued in this way, after a while may fall, especially when it is very warm or work in the room in the summer.

First remove the cabinet door.

So that the glass is not cracked, the mirror surface is needed all the time to make or make a side of plasticine and pour water there.

Remove the protective stickers from Scotch. Fix the long edge of the mirror on the markup line. Do not hurry, omit the mirror surface, trying to prevent displacement. Better if an assistant will work with you. He will make sure that the mirror lay exactly, without going beyond the applied markup. All, the mirror was glued. Now you need to wait when the glue dries. Optimally, the day is allocated. The door can be attached to the place.

So, you got stuck with all materials and tools, acquired the mirror of the desired size.

The mirror must lie on cardboard or fabric.

You decided not to use "liquid nails", but attach to the paws, then you need to make sure of their production accuracy in height and, if necessary, mount gaskets. They must close to the mirror, but without stretching. You also remove the door from the closet, put horizontally, place where the holes under fastening the paws, screw them down, flex. Before fastening the mirror, it is necessary to put a soft layer, then enhance the mirror with my paws.

From the tools will be useful: sandpaper, gun mount, pencil, line or roulette.

The gluing of the mirror on the cabinet door is not such a difficult thing, all work should be carried out very carefully.

If there are finished holes in the mirror, you can use special screws instead of foot. In case there are no holes, they are drilled by a diamond drill in the corners. So that the glass is not cracked, the mirror surface is needed all the time to make or make a side of plasticine and pour water there. The mirror must lie on cardboard or fabric. Plastic washers must necessarily be inserted under the head of the screws.

Before proceeding with work, you need to prepare materials.

As a result, the interior of the room will be very transformed

The gluing of the mirror on the cabinet door is not such a difficult thing, all work should be carried out very carefully. As a result, the interior of the room will be very transformed. It is not necessary that the mirror is rectangular or square. It can be any original form. It is important to fit to the overall setting.

The main thing is not to hurry, to perform all the work to be scrupulously, to come to the matter responsibly, then the mirror will be attached quite firmly and serves a long time.

It is not necessary that the mirror is rectangular or square.

It is important to fit to the overall setting.

VIDEO: How to glue the mirror. Mirror door swinging for furniture.

There are several ways to attach the mirror to furniture. It can be a small door of the suspension cabinet or a massive cabinet door.

The most common ways are:

on bilateral scotch
with the help of plastic stops or metal P-shaped legs,
on silicone,
with the help of screws.

We advise you to acquire mirrors reinforced from the opposite side with a special protective film that prevents the splinters. Such a mirror is much stronger and safer: its fragments will not be sprinkled if the mirror breaks down.

How to glue the mirror on double-sided tape. Initially, stick the tape around the perimeter back wall mirrors. After that, cover the additional vertical scotch strips at equal gaps. Before glueing the mirror, mark the border with a pencil, where the mirror will hang on the door. After that, the mirror can be glued.

On bilateral scotch, no matter how convenient, never glue large mirrors! The tape can break away and falls the mirror. Especially this probability increases in the hot season.

The second method - with the help of special metal p-shaped paws or plastic stops. The mirror must be attached to the door, which is removed from the loops and is in a horizontal position. When you use your foot, check their production accuracy. The height of the paws should be such that their tight fit to the glass is ensured. It should not be tension. If there is a need, then you need to install under the paws of the gasket. When you make the layout of the holes for the fastening of the paws, then screw the paws, then remove them, insert a soft underlying layer in the mirror. Then you need to squeeze the legs of the mirror.

The most convenient and durable way to attach the mirror is to glue with silicone. Consider in detail how to do it.

Apply milling lines on the door of the furniture where the mirror will be located.

The opposite side of the mirror and the surface where it will be glued, wipe for a solvent degreasing. It is advisable to do this with a veosh that does not leave the fibers and threads. Before applying adhesive substances, you need to give the solvent to completely evaporate.

Colorless construction Silicone - The most optimal option for sticking the mirror.

Apply silicone on the opposite direction of the mirror must be careful not to get on the front side or clothing. Make it with stripes at equal intervals. There is no need to apply silicone to the entire surface. Just like to apply abundant silicone stripes close to the edge.

Then you need to install the longest mirror edge on the line that you have applied in advance with a pencil.

How to glue the mirror to the cabinet door

Lunch the mirror with maximum caution so that there are no displacements relative to the marking lines. This is easier to do together: one smoothly lowers the mirror, and the other controls that the mirror is glued exactly on the marking lines.

Before hanging back the door, you need to give silicone to dry. For this, there is enough two hours.

And the least popular method of fastening the mirror - with the help of screws. To do this, drill at the corners of the hole mirror using diamond drills. During drilling, the surface of the mirror must be constantly wetted, and under the mirror lay a layer of soft cardboard or soft tissue. Under the heads of screws, it is desirable to insert plastic washers.

Hidden text

He worked in the same office, and saw one employee glued the mirror to LDSP on liquid nails. At the same time, he did not simply put the dashes and points, but also in the middle wrote glue - x ... th you. After two months, the analysis of flights, a trip to the customer, and alteration with apologies from an employee at his expense. I saw this mirror - it is increasingly kind, but at the top or sunny lighting - Letters, dashes and points slip. But glue was specifically for mirrors. Emalgam badly mean, or weather conditions, or not that day.
From life everything was.

How to attach the mirror to the closet: what are the ways?

Return to post number 3, I also prone to such an option about the frame.

How to glue the mirror to the cabinet door?

Wardrobe Coupe do it yourself<<

Step-by-step assembly doors wardrobe

How do you look if the process of assembling doors of the cabinet-coupe i will describe in steps? I think it will be clearer, and I may not forget to talk about the most important points of this process. So let's go! We will specifically believe that the details of the filling doors we already have, and we have left to collect frames from profiles.

Step 1. Perform cutting profiles. Before you proceed to assembling doors, you must cut out the details of the specified dimensions from profiles. As I said earlier, each manufacturer has its own numbers in formulas for calculating profiles. All these parameters are not a secret. It is enough for you to just ask this question from the company-seller of sliding systems. By the way, almost all sellers have an "Excele File", which automatically calculates the dimensions of profiles and fillings - it is enough to you, simply, fill the cells: "Length of the Owl" and "Height of the Owl". Although I personally prefer to manually check the accuracy of the calculation of this file. As the saying goes: "Seven times will die ..." In general, our first step is the calculation of the size of profiles and cutting.

Cutting the profile is best with the help of an accurate ending saw, after installing a well-sharpened saw blade to work on it. A blunt disk to cut a profile I do not recommend you - it is obligated it and troublesome. If you have no saw, then you can neatly cut the cutting with the help of the metal. As a result, you must have the same size all vertical profiles, as well as one size horizontal top and bottom profile. If the design of your door coupe "without perversions" - refers to "vertically horizontal" without diagonal connecting profiles, then all the connecting profiles will also be the same size as horizontal.

Step 2. Drills holes in a vertical profile handle. The profile is sliced, you can switch to drilling holes. Here I ask you to be attentive, since this process has some nuances. So, attention to the drawing:

Holes we drill with the outer end side of the vertical profile. In each profile we have only three holes: one at the top and two in the bottom. The figure shows the standard amount of indents for this type of sliding systems. However, I highly recommend that before performing the drilling of the holes, compare the data of the values \u200b\u200bin relation to its sliding system - rarely, but there are differences.

Now about the nuances. To make it easier for you to understand everything, I propose to look at this drawing:

I hope you all recognized the vertical profile handle (in the context). On the left is shown this profile to drowning holes, and on the right - after. As you can see, you will have to drill holes at the same time through two walls of the profile - so to speak, to make them through. I want to draw your attention that the outer hole in us has a diameter of 10 mm, and internal - 5.5 mm. Actually, our mounting screws and adjusting screws are calculated under the openings of 5.5 mm and are fixed on the inner wall of the profile, freely passing through a decade-minute opening of the outer wall. Due to this, they, as it were, hide inside the vertical profile, bringing us pleasure to your visual absence on visible sides of the door of the cabinet.

Now about the main thing. What is the order of drilling data holes? So, at first we drill through holes (through the outer and inner wall of the profile) with a drill with a diameter of 5.5 mm. And then with the help of a 10 mm drill, only the outer holes are drilled. And then you will also work, as in Figure: The outer wall diameter will be 10 mm, and internal - 5.5 mm. In principle, there is nothing complicated here, the main thing is nothing to forget and not confuse.

Step 3. We stick a mirror or brazing film with the back side. If you use mirrors or glasses as a filling of the door wardrobe, then you need to take care of the safety of the use of this design. There are different situations in life. Sometimes kids can "fool" and break the mirror door of the cabinet. There are cases when the wife and aims are arranged competitions in the accuracy of throwing a pan in the sheltered husband and son-in-law. But the prepared husband (son-in-law) is capable of avoiding a heavy item in any condition. But the door of the wardrobe - she can't. So the pans fly, and they split the doors of mirrors, and stands husband (son-in-law) on all fours, covering his head with his hands in anticipation of fragments falling on him from a broken mirror.

And fragments of stalk or mirrors are not a frying pan, there is a high risk of getting serious injury, sometimes even life-threatening. That is why it is extremely important to ensure safety when breaking the mirror or glass filling of the wardrobes. And this can be very simple. Attention:

In the figure, we see how a self-adhesive film is glued on the back of the mirror. Most often, "ORAKAL" is used for these purposes. The film passes over the entire area of \u200b\u200bthe mirror or glass. As a result, the broken fragments do not figure out in all directions, but remain hanging on the film to which they are glued.

I want to draw your attention to another important point. For the coastal of the rear, the mirror will suit both transparent and color self-adhesive film. But it is better to use transparent "ORAKAL" for the glass, if you need transparency of doors. If not, then you can stick the film and on a white basis.

Step 4. Install the horizontal profiles. The first are horizontal profiles. The most common problem with which you may encounter in the process of installing profiles are a tight entry of filling in the profile groove. In this case, a rubber hammer (pyzyanka) comes to help us. By the way, the silicone seal is pre-installed on filling from the mirror or glass:

The seal must be cut so that it is 5 mm shorter than the width of the mirror itself or glass on both sides.

Well, now go directly to the installation of horizontal profiles:

So, if the filling is tight in the profile groove, then, as mentioned above, we use the Cyanka, as well as a wooden bar. If there are no timber, then in principle, it will be suitable for some residue of the chipboard. The facing canvas with one side should be resting in reliable and even emphasis, and to the second side you attach a profile, put the wooden bar on it and start to knock on the corpuscate, thereby stinging a profile on the filling of the door-compartment. Blows must be accented. Also, it is also necessary to calculate the strength of the blows so that they are strong enough to pack the profile, but not so much to get used. In general, you need to "shoot", "feel" profile. You can even preliminarily exercise on the pruning of the profile and filling of the chipboard - so you can feel when the profile is starting to deform, and what power is the most optimal for its effective packing.

It is categorically undesirable to knock on the profile itself, since there is a high probability to drive, or damage the coverage of the profile, thereby spoiling the appearance of the finished doors.

I also want to note the moment that when installing a profile on a mirror or glass filling, you need to take care to the surface on which it will lie, was smooth and clean. You understand, the mirror (glass) - the material is fragile, requiring neat and reverent circulation. If in the process of packing profile the sealant will start sliding from the mirror, then you need to remove the profile, install the properly seal and start a package from the very beginning. Be sure to consider this moment! For if you continue to install a profile with a sliding seal, then most likely the mirror (glass) will be broken.

And one more advice to those who will work with a mirror or glass. If the profile is "hard to go" and you cannot install it, then a little stretch the seal in length - so you make it thinner and facilitate your work. Just do not overdo it! Remember that the mirror (glass) filling the door coupe should not hang inside the profile of the sliding system.

I also recommend that you collect the doors of the wardrobe together - it will be easier and more convenient. Even my professional collectors preferred to perform this work with their partners, acting on the principle: "better less, but earn something to pay from your own pocket for a broken mirror or spoiled profile."

Step 5. Install vertical profiles. Well, horizontal profiles are installed! It has arrived the time of installing vertical handle profiles:

The design turn on the edge, naturally, the surface of the floor or table should be smooth. Well, and then according to the standard procedure - with the help of a wooden bar and a painting, we set the vertical profile of the door-coupe.

Step 6. Install the rollers and twist the design by self-draws. So, our door is almost collected. It remains to install videos and fix all the details in their places with the help of assembly screws. This is how the installation scheme of rollers and self-tapping screws looks like:

Remember, in the previous publication, when we considered the design of the sliding doors, I told you about the purpose of semicircular grooves in horizontal profiles? Now, this scheme can clearly see how the upper and lower screws enter these the same grooves of the lower and upper horizontal profiles.

But here is not so simple.

How to glue the mirror to the cabinet

Yes, yes, here also have its own nuances. But let's all in order.

Algorithm for assembling the top of the door. So, at the top of the door with the help of assembly self-press, we need to twist a vertical profile and upper horizontal profile, as well as install the upper guide roller. Let's look at the order of the assembly. Attention to images:

At first we screw the assembly screws, but not to the end - we leave the place to install the upper roller, approximately as shown on the left figure. Then we install the roller and screw the screws until you stop. Thus, we not only pulled the vertical and horizontal profiles, but also recorded the top roller of the door coupe.

Algorithm for assembling the bottom door. There are no nuances - just tighten the vertical profile and lower horizontal profile. Then we insert the lower rollers inside the lower horizontal profile and through the bottom hole in the vertical profile we screw the adjusting screw into the structure of the bottom roller:

In general, the adjusting screw is a cool thing. With it, you can adjust the level of inclination of the door, putting it in the perfect position.

Actually, I congratulate you! Doors are ready! You did it! It remains to paste the buffer tape and you can move to the installation of guide rails for sliding doors.

Wardrobe Coupe do it yourself<<

Since for the first time in the world in 1373, the first mirror workshop opened in Nuremberg, the mirrors became inseparable satellites of a person. However, only wealthy people could afford in those distant times of the mirror. At the same time, the technology of manufacturing mirrors, which means their properties to reflect, somewhat chrome. Now it is nothing more than consumer goods, while with an excellent reflectivity, which can also afford everyone. It would be only desire.

The significance of mirrors in our life and their amazing properties

Indeed, the use of mirrors is difficult to overestimate. They are used in our everyday life, in science, medicine, optics, etc. Without them, you would say the world would have been different. But we will not fall into a certain paranoia about their amazing properties, because in essence, what we use our progress today today. And if so, the everyday unconscious use of the mirrors has already become our norm. In our apartment, you can often find one mirror: in the bathroom, in the corridor, in a wardrobe. At the same time, all these mirrors are somehow fixed in their places. Here, due to the fact that our site, primarily the construction subject, we already flaunt up professional interest. How is the mirror fastening in various variations, whether it is a tile, a wall, chipboard? It is this topic that our article will be devoted to how to fix a mirror without a framework, on various surfaces.

Mirror fastening methods

Despite the fact that in the previous paragraph of our article we allocated the types of surfaces to which the mirror can be attached. It also needs to pay attention to the possible way to attach them. What can be more relevant. And if we talk about these most methods of fastening mirrors, they are essentially three:

- with the help of mounting bilateral scotch;
- With glue. Often in this case, liquid nails are used;
- Mechanical method of fastening the mirror.

It is about these all methods for fastening the mirrors, and the possibility of using each of them for a particular surface, we will also describe further. In this case, we present specific examples.

How to fix the mirror with the help of bilateral mounting scotch

The first and simplest is the use of mounting bilateral tape. This material began to be used not so long ago. Moreover, for the attachment of everything in a row, including mirrors. However, there are no, conditions and limitations.
First, double-sided adhesion should be foam. That is, to have a certain thickness of 0.8 - 2 mm. This is necessary in order to compensate and smooth irregularities. In this case, the thickness of the tape must be about twice as many of these most irregularities on the surface to which the mirror is attached. Although it is difficult to determine, but still ...
Secondly, the technological process of mounting the mirror must be observed. In order not to be unfounded, we give a specific example of mounting the mirror on the Fiberboard plate. Usually such plates are used to make furniture.
Before proceeding to the description of the mirror installation process, it is necessary to say about the tape used, as well as on the installation conditions. The mounting tape for fastening the mirrors can be used in the temperature range from +10 to + 25 degrees. Lower or high temperatures do not provide proper adhesion tape with the surface. For installation, it is better to take a proven high-quality ribbon, for example, the company ZM. It can be:

- 9508W (base polyethylene, thickness 0.8 mm);
- 4492 (base polyethylene, thickness is 0.8 mm);
- 4032 (base polyurethane, thickness is 0.8 mm);
- 4026 (base polyurethane, 1.6 mm thick).

The ribbon consumption is taken at the rate of 60 square centimeters per 1 kg of weight. Provided that the mirror will hang vertically, and not on the ceiling or under a slope. In order for you to be easier to navigate with the cost, you can look at the table. It contains the ratio of the flow of the tape, depending on its thickness, the length and weight of the mirror.

Now directly to the action. The reverse surface of the mirror and fiberboard, to which the mirror will be pasted, should be cleaned using a vehicle and solvent (isopropanol, hexane). The use of other solvents for cleaning can say on adhesion between ribbon and glued material.

Now glue ribbon strips. Strips should be located point, that is, along the edges of the mirror, while evenly distributed over the surface.

This is necessary in order to compensate for the surface irregularities that can be in the space between the tape attachment points on the surface of the mirror. In the figure, although it is shown and exaggerated, but it is quite right that we have a mind.

We are trying on the mirror in place, while the protective film from the assembly scotch is not yet cleaned. We make a markup to put the mirror in the place from the first time, as it does not work after it.
Next, it is necessary to remove the protective film from the assembly tape and apply the mirror to the surface. Class glue on the mounting tag should be taken with a horizontal position of the mirror. If it is possible, you can load uniformly mirror uniformly distributed items on it. At least, press the mirror must be necessary. After a few hours, the Fiberboard with the mirror already fixed on it can be used for the production of furniture.

This method of fastening the mirror can be applied for already existing furniture, that is, when the mounting tape will be captured vertically. At the same time, the consumption of mounting tape will increase by 20 percent.
Now it is possible to use the mounting tape for other surfaces and materials. Scotch can be used, and, accordingly, secure the mirror on metals and metallized surfaces, most plastics (ABS plastic, polycarbonates, polyvinyl chloride, polyacrylates, polyesters), glass, ceramics, painted, primed and lacquered materials, treated wood, laminated chipboard.
It is impossible to use for silicone and rubber coatings, polyethylene, polypropylene, teflon, plasticized polyvinyl chloride, as well as non-toned concrete or DVP surfaces or if the surface is prone to resolving. What and why we think understandable and without our explanations.
Now about the second embodiment of the mirror when it is attached with glue.

How to fix the mirror with glue (sealant)

Again, not to talk about something surreal. Let us give a specific example that can be used for other cases when the mirror is glued to glue.

How to attach the mirror to the closet: practical advice

In our case, the mirror will be glued on the door. But before always on the materials used, that is, the glue used. No aggressive composition is suitable for use, which will not respond with primer and amalgam on the mirror. This is important not to spoil the appearance of the mirror on the front side. Usually, acrylic glue is ideal for this, essentially acrylic sealant. It can be drilled in tubes under the gun. Accordingly, all the conditions of use of sealant must comply with its packaging requirements.
Now about the mirror mounting process with glue. If there is an opportunity, then it is necessary to bring the surface to which the mirror will be glued into a horizontal position. In our case, remove the door and put it on the floor.

We try where the mirror will be located, and make marking.

Now we apply the sealant, you can point in the form of strips. Do not apply a lot of glue in one place, distribute it evenly over the entire surface. You should also not apply glue on the edges of the mirror installation area, so as not to squeeze it when laying the mirror outside.

We put the mirror on the door, pre-applying glue, and we wait until the sealant freezes.

It is fastened for the same acrylic sealant as a mirror, fix with a tape, before drying the glue.

Usually glue dries about a day.

Then remove the tape, and you can hang the door to the place.

Actually, this option can also be applied for other options when the mirror is glued to the wall. But in this case it will be necessary to hold the mirror before drying the sealant. It is possible to do this with the help of assembly scotch, that is, in the way, about which we told in the previous paragraph.

As a result, the mirror will be fixed on the assembly tape and glue. This is relevant when mounting tape may not cope with its tasks. Let's say in the bathroom, where it is wet and sometimes hot. Also, if it is a primed wall of concrete or drywall, then it is better to use the sealant and during its drying "to progress" with scotch.
Now about the last method of fastening the mirror, about mechanical mount.

How to fix the mirror using mechanical mounts

It should be noted that in today's construction market there are many accessories, fittings and fittings, in order to use as fasteners for mirrors. Just look at the photo.

We will give only one example using the fastening in the form of a dowel, with decorative hats. All other mounting options with mechanical fasteners will be similar. Is that the fastenings themselves will differ slightly.
Initially, I put the mirror to the wall and make the markup, where the fastener will be installed and how the mirror will be installed. Then we remove the mirror on the side.

In order to drill the hole of the desired depth, we use the tape that we wake on the drill.

So it will be visible, to which depth to drill the wall under the dowel. Drills holes.

Insert the dowels in the wall.

We set on the mirror on the reverse side of the plastic dampers. In fact, it is the washers under the self-tapping screw on the other side of the mirror. They are needed to compensate for the fastener effort when tightening it, and avoid the mirror breakdown.
Now install the mirror in place and screw the screws.

From above on a self-tapping screw wearing a hat.

That's all - the mirror is fixed. As you can see, this option is not so complicated and quite acceptable.

We summarize how to fix the mirror without frame on the wall, on the wall of the cabinet, on the tile

Summing up, it can be said that the options to consolidate the mirrors at least three main, using the assembly tape, glue and fasteners. And there are many of their private variations. If we talk about the advantage of choosing any of the options, here it is necessary to say that everyone has their own advantages and disadvantages. When mounting with the assembly tape and glue, the mirror is attached so that it is not visible on what it is hanging. This also does not require a special tool. In this case, the use of sealant is justified in cases of high humidity, but the scotch of moisture is afraid. By cons of the use of glue or assembly tape can be attributed to their disposable. If you cut the scotch or glue with a metal string, then fasten the mirror back will be much more complicated. It will be necessary to clean everything and all procedures first.
Mechanical fastening is good when you have a porous surface that is predisposed to resolving. Say the wall with whitewash. However, such a fastening is visible, as well as it can start corrosive over time. What rules the appearance, which means it is a certain minus. But to remove and put the mirror in place, during cosmetic repair will not be difficult.
So, what to use which of the options for fastening the mirror to solve you, we just have to hope that the choice will be faithful and the mirror will spend in its place for a long time and at the same time reliably.

It is difficult to imagine a modern interior without a mirror. But it is not only a beautiful, but very fragile material. Do not rush to throw away the broken cloth, it can well be renovated. This is especially true of vintage mirrors. If a mirror It does not lie to repair, then you should not throw fragments. Of these, beautiful mosaics are obtained, which will decorate not only the walls, but also such objects such as the table, headboard and even the entrance doors.

Instruction

Before glueing the mirror, clean and degrease the surface, using a conventional acetone (not a liquid for removing varnish!), Gasoline or a special cleaner that can be bought in a shopping store. To do this, apply a liquid to the tissue napkin and process the joints of the joint. After the procedure, do not touch degreased surfaces - it can significantly worsen the result of the work. Wait for a complete drying of the mirror

Prepare glue. Take the liquid glass, sugar and technical glycerin in a ratio of 50: 19: 5. Slightly warming up liquid glass, dissolve sugar in it, then gradually pour the glycerin and mix.
You can try such a recipe: Mills on a moderate fire Shellac, mix it with a turpentine in a 2: 1 ratio. Cool the mixture, divide it into small tiles. Before starting gluing, mass slightly heat.
Instead of the described compositions, you can use special glasses adhesives. Industry offers many types of compositions from ordinary to professional, incl.

How to glue the mirror to the cabinet door - a detailed description of the workflow

adhesives curable under the influence of UV rays. It will take a ultraviolet lamp for him.

Lubricate sections of split with a thin solid layer of glue. Mirror-processed parts Put on a horizontal surface, carefully connect and hold under pressure a few minutes.
If UV curing glue is used, after connecting parts, it will take the surface for 2 minutes by an ultraviolet lamp. Then remove the remnants of glue and repeat the glow.

A day later (when using UV glue, the term will be significantly less) to carefully consider the excess glue, speaking along the seam line. Now the mirror can be used.

March 7, 2018
Specialization: Master in the construction of plasterboard structures, finishing work and laying flooring. Installation of door and window blocks, finishing of facades, installation of electricians, plumbing and heating - for all types of work I can give detailed consultation.

Sticking mirrors on elements of furniture - the process is simple, but responsible. If you make mistakes and do everything wrong, then over time the mirror will begin to shift from its place or falls at all, and breaks. In the review, we will deal with how reliably and efficiently spend work, you will learn several ways and you can choose the one that best suits your situation.

Types of fastening methods

First of all, we will understand what methods can be fixed by mirrors. All of them proved their reliability, but the technology of work is varied and used for certain situations.

Mounting bilateral scotch

The simplest solution that has such advantages:

Two-way scotch allows you to glue items very quickly.. It equally reliably holds the mirrors, and glass, and other leafy materials. To understand the technology, you will need a couple of minutes, and the simplest set of devices, which is almost in every home and apartment;

The cost of this option is lowBut if quality is important to you, we recommend purchasing materials not from the budget, but at least from the average price segment. Choosing a specific decision, remember that the material should have a soft spacer, the usual stationery tape is not suitable, as it is not designed for high loads;
Buy tape will not be difficult.It is sold in construction stores, as well as in the outlets that are engaged in car spare parts. The second option is even preferable, since the automotive double-sided tapes are distinguished by increased strength and durability;

It is best to select a bilateral tape from 0.8 to 2 mm, it will smooth fine irregularities and ensure high adhesion strength with the surface. From manufacturers, the products of 3M have proven best of all, this option is recommended by professionals.

Glue elements best at temperatures from 10 to 25 degrees, It is this range that provides a solid fixation. Most often in the room the optimal microclimate, so there is no problems with this aspect, but if it is very hot in the room, it is better to wait until the temperature decreases so that the adhesive layer does not go to the tape and the mirror has not shifted;
Easy to calculate the required amount of material. Before gluing elements, the amount of tape required for work is calculated. To do this, you need to know the total weight of the mirror, 1 kilogram of the mass is used 60 sq.m. bilateral tape;
Ability to dismantle elements. If the mirror is pasted crookedly, then you can remove it and redo the job. To do this, use a guitar string or a thin ribbon of polystyrene, which cuts out the foamed part of the bilateral tape. After that, all the remnants of the old material are removed and the new one passes.

From the disadvantages you can select the following:

Double-sided tape is not suitable for heavy mirrors. If the size of the element is large and the weight is significant, then it is better to choose another method of fastening. This option is optimal for small mirrors;
It is important to purchase high-quality material.. Many poor-quality tapes are on sale, which do not provide a proper level of strength.

Special compositions and liquid nails

The most popular option that allows you to glue mirrors to any surfaces:

Chipboard and ldsp;
Tile in the bathroom or in the kitchen;
Wooden and veneered bases;
Plaster, concrete and oxpackled surface.

Since we understand how to stick the mirrors on the furniture, then we will analyze this option in more detail. Let's start with the advantages:

Low cost. The price of the compositions is low, and they are sold in all construction stores;
A wide variety of options. Different solutions are used - from special compositions to liquid nails and silicone for glass. It is best to use silicone, since the composition of liquid nails includes ammonia, which over time can damage the amalgam of the mirror and spots come on the surface;

High reliability. If the elements are fastened by technology, the fixation strength will be perfect. Below the workflow is disassembled in detail so that you can make gluing on your own.

Of the minuses it is worth noting the following:

The impossibility of dismantling. After the composition was frozen, separate the mirror from the door of the cabinet or panel in the hallway will not succeed. We will have to change the element entirely, and these are high costs;
The importance of the right work. If the technology is broken, that is, the danger that the mirror simply falls off with time. In addition, if an inappropriate composition is used, then with time the mirror can be spoiled.

Mechanical fastening method

In this case, a special fastener is used, which is designed to install mirrors on furniture. There are several basic options:

Metal brace. The simplest and cheap solution, which is metal elements, bent so that they have a mirror of a certain thickness. In order for the fastening from excessive effort, cracks on the surface are not formed, silicone gaskets are underway under the bottom;

Through holders - allow you to attach mirrors to any surfaces. From the outside, the installation location closes the decorative part, and inside the self-sufficiency or a dowel, depending on where the installation is made. This option is more complicated by the fact that it is necessary to produce glass drilling, and this is a difficult lesson, besides, you will need a special drill;

Furniture fasteners with decorative lining. Most often, it is done in the form of clamps that hold the mirror from above and below, and outside the installation site is closed with a decorative plug of any color and shape. With this option, you can hang the mirror anywhere;

The advantages of this solution are:

This is a secure installation option.. No need to worry that the mirror slides over time;
You can dismantle the element. If the mirror is damaged, then it will not be difficult to replace it, fasteners turns around quickly and easily;
Many options. Pick up the optimal will not work.

There are also its cons:

Installation complexity. Attachment requires a screwdriver to drill holes and twist the screws. If you are mistaken with a drilling site, then it will not be able to close the hole, the upper film of the coating will be corrupted;
Not very attractive species. The plugs do not always fit into the design, and this is the main problem.

How to make yourself glue the mirror to the cabinet door

We will look at how to glue an element to silicone, since this is the easiest and easier for a reliable option. This method is suitable for any designs, the main thing is to work correctly and use quality materials.

Materials for work

First, collect everything you need:

Special silicone for glasses and mirrors. Sold in construction stores and is characterized by the fact that it does not contain mirrors damaging the amalgam. In addition, the compositions of this group have high adhesion to smooth surfaces;

If you found liquid nails, which have a mark "for mirrors", you can use them.

Composition for degreasing surfaces. Remove the traces of fat and other substances from the furniture and the reverse side of the mirror with the help of White spirit or another universal solvent. Special automotive compounds can be used for degreasing, they are more expensive, but they almost do not smell;

Mirror of the desired size. Permanently measure the measurements and order the element in the finished form, the ends will be processed in it, which is very important for safety.

Tool

Fixing the mirror is performed using such devices:

Pistol for applying sealant. With it, work will pass quickly and efficiently and the cost consumption will be minimal. The cheapest option is suitable, since the load in the process of work on the tool will be low;

Measuring tool. To accurately determine the location of the mirror, a construction roulette or a ruler is used. And for marking, it is best to use a building pencil or a felt-tip pen;
Ribs for degreasing surfaces. Here any clean rag is suitable;
Screwdriver or screwdriver. If the mirror is put on the door in the cabinet, it is better to remove it, as it must lie horizontally;
Heavy items. To press the glass to the surface of the furniture, burden on it. You can use healthy elements or even ordinary banks in which water is nanit.

Fastening process: Step-by-step instruction

We'll figure it out how to attach the mirror with your own hands:

Illustration	Description
	Prepared workplace. It is best to make flooring, to which the door or another element of furniture is stacked, to which the mirror will be glued, it can be placed nearby, if there is enough space.
	The door of the cabinet is preparedThe following actions are performed: On the surface with a roulette and a pencil there is a position of the mirror. You can even attach a carved element, align it and make tags by template, is the most accurate option; Next degreases the surface, for this, a rag or a sponge is wetted in a solvent and the base is thoroughly wiping to remove everything too much.
	Mirror is preparing. For this purpose, the element is turned over the front side down and is carefully wiping into the same cloth moistened in the solvent. In order not to damage the front surface of the mirror, put on the flooring soft tissue.
	Silicone composition is applied. For this, the tube is inserted into the gun, the hole is cut, after which you can start work. The composition is distributed by zigzags in increments of about 100 mm, the indent from the edges should not be more than 30 mm.
	You need to accurately install the mirror on the markup. To do this, the long vertical edge is made along the line and aligns. If the length of the mirror is big, it is better to attract assistant to work.
	The mirror is neatly lowered and pressed against the surface. It is important to do the work accurately that the edge does not move and the element does not twist.
	The position of the element is checkedIf there are small displacements, it will not be difficult to move the mirror slightly, it is done in the first few minutes until Silicon grabbed.
	Built burden. It is left for a day, during this time Silicone is settled and parts manage to be very securely to stick together.

Output

Now you know three ways to fasten the mirrors on the furniture and you can spend your work on your own. The video in the article will tell more detail the information on the topic, but if you have questions - write them in the comments.

March 7, 2018.

If you want to express your gratitude, add clarification or objection to ask the author - add a comment or tell me thanks!

We laugh between them sealant.

We put the mirror on the facade, until you pressed and the scotch does not "hooked", and the sealant is not drying, it can be signed at the place

We put the mirror (through a soft gasket) and leave for a day

Previously I tried to glue on liquid nails. But ammonia, which is contained in them, they say, the Amalgam damages over the years. I honestly, until I noticed - 2 years old, flight ...

0 0

If you have a need and questions appeared how to stick the mirror on the closet, then this article will answer your questions. It is noteworthy that the size of the mirror does not matter.

The whole process can be streamlined in this way. Previously, make sure that you have applied to the commodity lines of the future position of the mirror.
1) We use a solvent or any other liquid for degreasing the surface on which you are going to attach the mirror. In most cases, this procedure can be the door of the cabinet.

2) Wipe the same liquid and the mirror itself.

3) To glue it to high quality and without subsequent problems, a colorless construction silicone has been tested for years.

Remember that if you are interested in how to stick the mirror on the closet, then forget about "liquid nails" or liquid masts of the type of glue "moment" with a strong smell. They include substances that later can ...

0 0

For the convenience of fitting clothes right in front of the dressing room, the mirror can be attached to the cabinet door. Its dimensions will depend on your capabilities and size of the door itself, but it is better, of course, have a mirror to display a complete height of a person. The mirror acquired in the store already has treated edges. If the mirror has been cut independently, the edges are handled with a grinding stone for knives. On the cabinet door, make the markup with a pencil with a ruler for a more even fastening. How to glue the mirror on the closet so that it does not fall, consider it from the frequent opening of its doors further.

Decreases the surface of the door and mirrors, which or solvent or alcohol. On the entire perimeter of the canvas, we glue the bilateral scotch strips, it is necessary in order to give glue to grab. With the help of a mounting gun, we apply a mirror glue to the back side of the mirror canvas strips, at a distance of ten and fifteen centimeters from each other ....

0 0

How to glue the mirror on the cabinet door ®

Tell me, please, what to attach or glue the mirror on the cabinet door? In the instructions are written by double-sided scotch, I really doubt that the tape will hold. The size of the mirror is approximately: height 150 cm, width 25-30 cm.

There are many different people on the forums ykt.ru. According to statistics, most of the violations of the law requirement, especially in the form of frank insults and cases of incitement of an interethnic retail, occurs in an anonymous mode. In this regard, themes, moderators and veterans of the forum are assigned the status of rating protection secreted by the R. icon. This means that in this thread cannot leave comments anonymous or newly registered users. The minimum rating to participate these topics is currently set to 40. To obtain it, it is sufficient for example, to create one discussed ...

0 0

How to glue the mirror.

Sometimes it becomes necessary to glue the mirror on the chipboard or another smooth surface - how to do and what to glue it. I will try to help you and tell you how to glue the mirror. There are many ways, but I will tell you about the most simple. If you need to glue the mirror on a smooth surface, let's allow the cabinet door, then you need two-sided tape, liquid nails or silicone, 3-4 Fiberboard strips superior in length Minimum mirror size and 2-4 cm wide, Mr. Muscle or other means for Washing glass.

For a more convenient and comfortable gluing of the mirror, you need a part to which we will stick to put horizontally. If it is a facade, it must be removed from the loops and put on the table or on the floor (if the facade has large dimensions and does not fit on the surface of the table) the front surface up. Those. That side to which we will stick the mirror up. If the dimensions of your mirror are less than ...

0 0

But even if you did not leave a place for the mirror, it can be glued to the surface of the tile using a special double-sided tape. On the entire perimeter of the canvas, we glue the bilateral scotch strips, it is necessary in order to give glue to grab. Then you can glue the mirror for double-sided tape. To do this, select the waterproof tape, which is the best suitable for the bathroom.

With a size of up to 20 cm (bottom fangs) fit. It also has a color - fangs will be covered with white, and this is not good. One of my friend sticks the fangs to the medallion and the plug to the fangs and dismissed the non-visible option. This allows the appraisers to bend the fang from the medallion and measure.

Additionally, large fangs supply in small pieces of double-sided thick tape for additional mounting to the medallion, which eliminates the boltak. Good evening! In the morning I took the fangs and drove to buy the case for painting, took: 1.

In a rush with fangs, she paste ...

0 0

Here is another very good option. How to glue the mirror on the cabinet door?

Podolstroy.com.ua, 10.24.2014

Here is another very good option. With gluing mirrors and not only cope Krass liquid nails for mirrors.

Excellent results gives gluing a mirror on silicone sealant in combination with bilateral scotch.

Degrease the surface of the mirror and chipboard acetone or other solvent

We stick stripes or squares of Scotch (many say that the strips are better - I am glue of squares)

The mirror has a rear layer of coating working, so glue can damage it. Although for the experiment, apply Cosmofen glue to others. Any old mirror, if the coating does not happen, then this glue will hold even an elephant. And if all the damages are damaged, then fasten with small metal. brackets. Although you can do and plastic. I took the basis from the cable of the canal, that part that attached to the wall, cut it in half and was attached to the wall where ...

0 0

Instruction

Pick up the mirror of such a thickness so that it does not be an obstacle to the movement of the doors in the wardrobe slots. If the mirrored canvas you purchased does not have a treated edge, or its shape and the area more square allocated to the mirror on the door, make it trimming. For this, first of all, remove the measurements from the cabinet door.

Gently put the mirror on a flat surface. Amalgam should be on top. Transfer to the linen dimensions. On the cut line, wet the amalgam with a solution of vinegar or ordinary water. Apply the rule and spend along its edge with chalk. Then take the needle and just over the cut line, we roll amalgam.

Turn the mirror canvas and glass cutting line, the symmetric line of the cut, carried out by amalgam. Metallic part of glass cutter lead along the line. When the chip will become noticeable, climb the surplus glass. Amalgam dried with a hairdryer.

Remove and place the door ...

0 0

How to attach a mirror on the cabinet door

The mirror is one of the most popular interior elements of the room. The mirror surface may be present in any room in various configurations of form and size. The most popular places for such an interior element - an entrance hall and a bedroom. But, if in the first case the correctly installed mirror can increase the space, fill the room, then in the bedroom its presence is sometimes doubted. The mirrors in the bedroom can be alarming and discomfort, but do not need to abandon them, as the room where we sleep is an even place for dressing up, making makeup.

How to attach a mirror?

Saving psychological comfort in the room can the correct competent location of the mirror, for example, for conducting a space procedure, you can install it on the toilet table, and in order to change clothes, you can fix the mirror on the cabinet door.

Choice

Now the acquisition is considered popular ...

0 0

If you need to glue the mirror to some surface in the apartment or in the country, and you did not do this before, this material is addressed to you.

Without a mirror, no modern house is required. The mirror is needed in the hallway, and in the bathroom, and in the living room, and in other rooms it will not be superfluous. You can just look at the mirror, or it can play your role in the interior design, or serve both these goals.

Already the finished mirror in the frame or mounted in the furniture is very simple. If your tasks dictate the placement of the mirror right on the wall without a frame, it is a more difficult job. The large size of the mirror (for example, from the floor to the ceiling), too, the task will not be simplified. However, glue the mirror of any size can be very secure and for a long time if you do it with the mind and high-quality glue.

Placing the mirror, like any other work, begins with the planning stage. Decide with the exact dimensions of the mirror before ordering it in the workshop. With accuracy ...

0 0

noncredo (5.6.2008, 15:46) wrote:

Sorry for the inaccuracy: blush: Something yesterday I crossed me: instead of Silicon wrote "Silicat".

Thanks to the Samseberentro and a specialist for the advice. If no one confirms to me the possibility of using the already purchased silicone glue-sealant (Germany), you will have to buy specials. For mirrors.

It is better to use special glue. It will be calmer. Any other adhesives, sealants, scotchi, of course, stick the mirror. But how much will it last? Will it fall? Will there be collapsed from the reverse side (amalgam)?
Why suffer these issues?
People (and professionals) have already worked on this. Conducted survey, research, testing. Take advantage of their results. In the link given by me above the link 330gr.
And about Scotchi - you will be especially careful. It can only be used as temporary fixation until the main glue dries.
I, in order of expirement, glued to the automotive 2-sided ...

0 0

There are several ways to attach the mirror to furniture. It can be a small door of the suspension cabinet or a massive cabinet door.

The most common ways are:

For bilateral scotch, with the help of plastic stops or metal P-shaped paws, to silicone, with screws.

How to glue a mirror for double-sided tape? Initially, stick the tape around the perimeter of the rear wall of the mirror. After that, cover the additional vertical scotch strips at equal gaps. Before glueing the mirror, mark ...

0 0