Handbook of the fitter assembler MK 4 category. Profession Locksmith for the assembly of metal structures (4th grade) in the Unified Tariff and Qualification Handbook. Preface to job description

\Typical job description of a locksmith for the assembly of metal structures of the 4th grade

Job description of a locksmith for the assembly of metal structures of the 4th grade

Position: Locksmith for the assembly of metal structures of the 4th category
Subdivision: _________________________

1. General Provisions:

Subordination:

A metalworker of the 4th category is directly subordinate to ........................
A metalworker of the 4th grade follows the instructions ........................................ ............

(the instructions of these employees are carried out only if they do not contradict the instructions of the immediate supervisor).

Substitution:

A locksmith for the assembly of metal structures of the 4th category replaces ......................................... ........................................
A locksmith for the assembly of metal structures of the 4th category is replaced by ......................................... ......................................

Reception and dismissal:
A fitter for the assembly of metal structures is appointed and dismissed by the head of the department in agreement with the head of the department.

2. Qualification requirements:

Must know:

technical conditions for the assembly of complex metal structures
system of tolerances and landings
qualities and roughness parameters
the effect of heating metals (during welding) on their deformation
weld symbols
methods of aligning complex steel structures
installation rules and arrangement of lifting mechanisms and devices
methods of straightening complex metal structures in fixtures using templates and drawings
device and rules for setting up manual pneumatic machines.

3. Job responsibilities:

Assembly of complex assemblies of metal structures for welding and riveting according to drawings and assembly diagrams using universal fixtures, as well as assembly of complex assemblies of metal structures using universal assembly and special fixtures and templates.
Marking of places for the installation of complex basic parts and assemblies of metal structures.
Editing of complex and complex parts and assemblies of metal structures.
Cleaning for gumming of welded seams with a manual pneumatic grinder.
Participation in the assembly of experimental and unique assemblies of metal structures under the guidance of a more highly qualified locksmith.
Hydraulic and pneumatic testing of complex assemblies of metal structures operating under pressure.
Elimination of defects discovered after testing complex assemblies of metal structures.
Drawing up sketches and assembly diagrams.
Assembly, lifting and installation with temporary distribution of metal structures in different positions at different heights.

page 1 Job description Metalwork assembly fitter
page 2 Job description Metalwork assembly fitter

4. Rights

A metalwork assembly fitter has the right to give assignments to subordinate employees, assignments on a range of issues that are part of his functional duties.
A metalworker assembling a metal structure has the right to control the execution of production tasks, the timely execution of individual orders by employees subordinate to him.
The metalwork assembly fitter has the right to request and receive the necessary materials and documents related to the issues of his activities and the activities of employees subordinate to him.
The metalwork assembly fitter has the right to interact with other services of the enterprise on production and other issues that are part of his functional duties.
The fitter for the assembly of metal structures has the right to get acquainted with the draft decisions of the company's management regarding the activities of the Division.
The metalwork assembly fitter has the right to propose to the manager for consideration proposals for improving the work related to the duties provided for in this Job Description.
A metalwork assembly fitter has the right to submit to the manager for consideration proposals on encouraging distinguished workers, imposing penalties on violators of production and labor discipline.
A fitter for the assembly of metal structures has the right to report to the manager about all identified violations and shortcomings in connection with the work performed.

5. Responsibility

A metalworker assembling metal structures is responsible for improper performance or non-performance of his duties as provided for by this job description - within the limits determined by the labor legislation of the Russian Federation.
The metalworker is responsible for violation of the rules and regulations governing the activities of the enterprise.
In case of transfer to another job or dismissal from the position, the metalworker is responsible for the proper and timely delivery of cases to the person taking the current position, and in the absence of such, to the person replacing him or directly to his manager.
A metalworker assembling metal structures is responsible for offenses committed in the course of carrying out his activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.
A fitter for the assembly of metal structures is responsible for causing material damage - within the limits determined by the current labor and civil legislation of the Russian Federation.
The metalworker is responsible for compliance with the applicable instructions, orders and orders for the preservation of trade secrets and confidential information.
A metalworker is responsible for compliance with internal regulations, safety and fire safety rules.

This job description was developed in accordance with (name, number and date of the document)

Head of structural

I APPROVE:

[Job title]

_______________________________

[Name of company]

_______________________________

_______________________/[FULL NAME.]/

"______" _______________ 20___

JOB DESCRIPTION

Locksmith for the assembly of metal structures of the 4th category

1. General Provisions

1.1. This job description defines and regulates the powers, functional and job responsibilities, rights and responsibilities of a locksmith for the assembly of metal structures of the 4th category [Name of the organization in the genitive case] (hereinafter - the Company).

1.2. A metalworker of the 4th grade is appointed and dismissed in accordance with the procedure established by the current labor legislation by order of the head of the Company.

1.3. A metalworker of the 4th grade belongs to the category of workers and reports directly to the [name of the position of the immediate supervisor in the dative case] of the Company.

1.4. The 4th grade metalwork assembly fitter is responsible for:

timely and high-quality performance of tasks for their intended purpose;
compliance with performance and labor discipline;
compliance with labor safety measures, maintaining order, compliance with fire safety rules at the assigned work site (workplace).

1.5. A person with a secondary specialized education in this specialty and work experience of at least 1 year is appointed to the position of a metalwork assembly fitter of the 4th category.

1.6. In practice, a metalworker assembling grade 4 metal structures should be guided by:

local acts and organizational and administrative documents of the Company;
internal labor regulations;
occupational health and safety regulations, industrial sanitation and fire protection;
instructions, orders, decisions and instructions of the immediate supervisor;
this job description.

1.7. A metalworker of the 4th grade should know:

technical conditions for the assembly of complex metal structures;
system of tolerances and landings;
qualities and roughness parameters;
the effect of heating metals (during welding) on their deformation;
symbols of welded seams;
methods of aligning complex steel structures;
installation rules and arrangement of lifting mechanisms and devices;
methods of straightening complex metal structures in fixtures using templates and drawings;
device and rules for setting up manual pneumatic machines.

1.8. During the temporary absence of a metalworker assembling grade 4 metal structures, his duties are assigned to [the name of the position of the deputy].

2. Functional responsibilities

The 4th grade metalwork assembly locksmith performs the following labor functions:

2.1. Assembly of complex assemblies of metal structures for welding and riveting according to drawings and assembly diagrams using universal fixtures, as well as assembly of complex assemblies of metal structures using universal assembly and special fixtures and templates.

2.2. Marking of places for the installation of complex basic parts and assemblies of metal structures.

2.3. Editing of complex and complex parts and assemblies of metal structures.

2.4. Cleaning for gumming of welded seams with a manual pneumatic grinder.

2.5. Participation in the assembly of experimental and unique assemblies of metal structures under the guidance of a more highly qualified locksmith.

2.6. Hydraulic and pneumatic testing of complex assemblies of metal structures operating under pressure.

2.7. Elimination of defects discovered after testing complex assemblies of metal structures.

2.8. Drawing up sketches and assembly diagrams.

2.9. Assembly, lifting and installation with temporary distribution of metal structures in different positions at different heights.

In case of official necessity, a metalworker of the 4th category can be involved in the performance of his official duties overtime, in the manner prescribed by law.

3. Rights

A metalwork assembly fitter of the 4th grade has the right to:

3.1. To get acquainted with the draft decisions of the management of the enterprise concerning its activities.

3.2. Submit proposals for improving the work related to the responsibilities provided for in this job description for the management's consideration.

3.3. Inform the immediate supervisor about all deficiencies in the production activities of the enterprise (its structural divisions) identified in the course of the performance of their duties and make proposals for their elimination.

3.4. To request, personally or on behalf of a direct supervisor, from the heads of the enterprise departments and specialists, information and documents necessary for the performance of their official duties.

3.5. To involve specialists from all (individual) structural divisions of the Company in solving the tasks assigned to him (if this is provided for by the provisions on structural divisions, if not - with the permission of the head of the Company).

3.6. Require the management of the enterprise to assist in the performance of their duties and rights.

4. Responsibility and performance evaluation

4.1. A metalworker of the 4th category bears administrative, disciplinary and material (and in some cases stipulated by the legislation of the Russian Federation - and criminal) responsibility for:

4.1.1. Failure to comply or improper fulfillment of the official instructions of the immediate supervisor.

4.1.2. Failure to perform or improper performance of his labor functions and the tasks assigned to him.

4.1.3. Misuse of the granted official powers, as well as their use for personal purposes.

4.1.4. Inaccurate information about the status of the work entrusted to him.

4.1.5. Failure to take measures to suppress the identified violations of safety regulations, fire safety and other rules that pose a threat to the activities of the enterprise and its employees.

4.1.6. Failure to enforce labor discipline.

4.2. Assessment of the work of a locksmith on the assembly of metal structures of the 4th category is carried out:

4.2.1. Immediate supervisor - regularly, in the process of the employee's daily performance of his labor functions.

4.2.2. The attestation commission of the enterprise - periodically, but at least once every two years, based on the documented results of the work for the evaluation period.

4.3. The main criterion for evaluating the work of a locksmith on the assembly of metal structures of the 4th grade is the quality, completeness and timeliness of his performance of the tasks provided for in this instruction.

5. Working conditions

5.1. The work schedule of a metalworker assembling grade 4 metal structures is determined in accordance with the internal labor regulations established by the Company.

5.2. Due to the production necessity, a metalworker of the 4th category is obliged to go on business trips (including local ones).

Acquainted with the instructions ___________ / ____________ / "____" _______ 20__

§ 139. Locksmith for the assembly of metal structures of the 2nd category

Description of works... Manual chopping and cutting of wire, sheet and section metal blanks. Sawing and deburring. Participation, under the guidance of a locksmith of higher qualifications, in the performance of individual simple and medium-complexity works and operations on the assembly of metal structures and during their testing. Manufacturing of simple parts from bar and sheet metal. Part marking using simple templates. Driving and cutting threads manually with taps and dies. Alignment of assembly racks. Installation of bolts and studs in the matching holes of metal structures. Assembly of simple assemblies of metal structures for welding and riveting according to drawings and sketches using universal assembly and special devices. Tacking parts during assembly by electric welding. Drilling, reaming and reaming of small parts holes according to the markings on the machine and portable power tools. Editing of parts and assemblies of metal structures.

Must know: the name and purpose of locksmith and measuring tools and devices and their application; ways of refueling locksmith tools; techniques for performing simple and medium-complexity locksmith operations and the process of assembling simple and medium-complexity metalwork assemblies; device and rules of operation of lifting and transporting devices, working and measuring instruments and devices; technological process, methods and techniques for assembling, fitting, checking and straightening metal structures; system of tolerances and landings; properties, brands and assortment of materials and pipes used; methods of joining parts for welding; rules and types of marking of assembled units.

Work examples

1. Cylindrical tanks and vessels operating under pressure up to 5 MPa (60 kgf / sq. Cm) - assembly and hydraulic test.

2. Parts from sheet and strip steel - marking by template, straightening.

3. Sheet steel parts - bending.

4. Parts made of section steel of all profiles with a thickness of up to and over 6 mm - cutting, chopping

5. The details are different - filing free sizes, cutting at corners, drilling according to the marking.

6. Small-sized casings - assembly.

7. Caps, lids, brushes, vessels, funnels, boxes, cabinets of all sizes - preparation, straightening and assembly of parts for welding.

8. Sheet and profile metal - drilling, cutting with guillotine and press-shears, joining for welding.

9. Strip and twisted metal - bending and stripping after gas cutting.

10. Butt pads, stiffeners, temporary bolts - installation.

11. Supports and frames for apparatus - assembly.

12. Gaskets of simple and complex configuration made of sheet steel, cardboard, asbestos, clinoherite, rubber - cutting and cutting according to marking by hand.

13. Staples made of material of different sections - flexible in the device.

14. Welded racks - assembly for welding.

15. Belt conveyors - assembly of metal structures.

16. Pipe fittings with flanges - assembly.

17. Metal cabinets and shelves - assembly.

§ 140. Locksmith for the assembly of metal structures of the 3rd category

Description of works... Assembly of units of metal structures of medium complexity for welding and riveting according to drawings and sketches with the use of universal devices, as well as the assembly of complex units of metal structures using universal assembly and special devices and templates. Adjustment of sealing surfaces. Marking of places for the installation of simple basic parts and assemblies of metal structures. Assembly of complex metal structures together with a mechanic and an electric welder of a higher qualification. Editing of parts and assemblies of metal structures of medium complexity. Hydraulic and pneumatic testing of units of medium-complexity metal structures operating under pressure.

Must know: methods of marking places for the installation of basic parts and assemblies of metal structures; constructive arrangement of devices used during assembly; methods of sharpening locksmith tools; state standards for the materials used; a system of tolerances, landings and their designations in the drawings; requirements for the work performed; rules for working with a gas cutting machine and an electric welding machine; the sequence and methods of assembly on assembly racks and by conductor-copiers; assortment and grades of steels.

Work examples

1. Low pressure washers with detachable connections - assembly.

2. Oil tanks - production and assembly.

3. Cylindrical tanks and other vessels operating under pressure over 5 to 15 MPa (50 to 150 kgf / sq. Cm) - assembly and hydraulic testing.

4. I-beams for monorails - assembly.

5. Baths of rolling equipment and oil gearboxes, casting ladles of various capacities - assembly for welding.

6. Insulation of manifolds - fabrication and assembly of parts.

7. Plate and overhead conveyors - assembly of metal structures.

8. Door and window frames and metal doors with a rigid frame - assembly.

9. Counterweight bodies - weld assembly.

10. Ladders, platforms, purlins, bunker walls, decks, metal railings made of pipes and tees, brake sheets, fences, sliding supports, gratings - assembly.

11. Cylindrical and conical shells made of sheet metal - bending.

12. Settling basins, measuring tanks, collectors - assembly.

13. Foundation slabs - assembly.

14. Louvered grilles, flooring for openings, bar posts for fixing conductors, conductor for anchor bolts - assembly.

15. Bars of I-section - assembly of metal structures.

16. Farms - copier assembly.

§ 141. Locksmith for the assembly of metal structures of the 4th category

Description of works... Assembly of complex assemblies of metal structures for welding and riveting according to drawings and assembly diagrams using universal fixtures, as well as assembly of complex assemblies of metal structures using universal assembly and special fixtures and templates. Marking of places for the installation of complex basic parts and assemblies of metal structures. Editing of complex and complex parts and assemblies of metal structures. Cleaning for gumming of welded seams with a manual pneumatic grinder. Participation in the assembly of experimental and unique assemblies of metal structures under the guidance of a locksmith of higher qualifications. Hydraulic and pneumatic testing of complex assemblies of metal structures operating under pressure. Elimination of defects discovered after testing complex assemblies of metal structures. Drawing up sketches and assembly diagrams. Assembly, lifting and installation with temporary distribution of metal structures in different positions at different heights.

Must know: technical conditions for the assembly of complex metal structures; system of tolerances and landings; qualities and roughness parameters; the effect of heating metals (during welding) on their deformation; symbols of welded seams; methods of aligning complex steel structures; installation rules and arrangement of lifting mechanisms and devices; methods of straightening complex metal structures in fixtures using templates and drawings; device and rules for setting up manual pneumatic machines.

Work examples

1. A-shaped excavator trusses - assembly of individual units.

2. Cylindrical tanks and other vessels operating under pressure over 15 to 30 MPa (150 to 300 kgf / sq. Cm) - assembly and hydrotesting.

3. Tanks of T-shaped, box-shaped and lattice cross-sections for load-bearing metal structures - assembly.

4. Mixer bands - assembly.

5. Mixing drums with internal spirals - assembly.

6. Cell shafts of disc vacuum filters made of high-alloy steel - assembly.

7. Auger screws - assembly.

8. Rig derricks - assembly of separate parts of metal structures.

9. Gas tanks, air collectors and water separators - assembly.

10. Gas pipelines - assembly.

11. Turbine casing frames - assembly.

12. Frames and casings of industrial ovens and dryers - assembly.

13. Protective casings - assembly, installation.

14. Constructions of bearing bridges of pipelines - assembly.

15. Conductors, copiers for farms - assembly.

16. Housings of evaporators and condensers - assembly with spherical bottoms and fittings for welding.

17. Cranes with lifting capacity up to 100 tons - assembly of structures and individual units.

18. Monorails - assembly.

19. Lattice supports - assembly.

20. Tanks welded overall - assembly.

21. Ties and spacers - assembly.

22. Drying drum nozzle sections - assembly.

23. Traverses - assembly for welding.

24. Half-timbered houses - assembly of purlins and elements.

25. Refrigerators and blast furnace tilting machines - fabrication and assembly.

26. Cabinets and boxes (waterproof) - assembly.

27. Electric and turbo blowers - assembly.

28. Elements of radio towers, power line supports - assembly.

29. Elevators, smoke exhausters, exhausters - assembly.

§ 142. Locksmith for the assembly of metal structures of the 5th category

Description of works... Assembly of complex assemblies of metal structures for welding and riveting according to drawings and assembly diagrams using universal and special devices and templates. Marking of places for the installation of complex basic parts and assemblies of metal structures. Leveling and alignment of assembled metal structures. Creation of simple geometric shapes from assembly diagrams and sketch sketches. Assembly of experimental and unique metal structures. Hydraulic and pneumatic testing of complex assemblies of metal structures operating under pressure. Elimination of defects discovered after testing complex assemblies of metal structures.

Must know: the appointment of various kinds of complex metal structures; operating conditions of lifting and transport devices, methods for determining their reliability; mechanical properties of base metals; permissible tensile, bending, compression forces; mechanical characteristics of the used lifting mechanisms; techniques for performing rigging and welding works; the procedure for organizing work on the assembly of complex metal structures; ways of marking complex sweeps.

Work examples

1. Excavator base - assembly.

2. Water pressure tanks, gas ducts, bunkers and chimneys - assembly.

3. Cylindrical tanks and other vessels operating under pressure over 30 MPa (300 kgf / sq. Cm) - assembly and hydrotesting.

4. Beams of the main and end bridge cranes - assembly.

5. Drums: coal grinding, ore grinding mills, mine machines - assembly.

6. Towers and frames for scoop dredgers - parts manufacturing.

7. Car dumpers - assembly.

8. Sluice gates - assembly.

9. Thin-walled telescopic special steel casings - assembly.

10. Metal structures (trusses, columns, rafters, blocks, casings) - assembly, inspection of all structures.

11. Bridge structures - assembly.

12. Construction structures - control and enlarged assembly, alignment.

13. Containers with a carrying capacity of over 0.5 tons and organizational equipment with mechanical, telescopic and other drives for movement or lifting of loads - manufacturing, assembly, adjustment and testing.

14. Mine pile drivers - parts manufacturing.

15. Housings of heat exchangers - assembly.

16. Shells of cement, metallurgical and other complex furnaces - complete assembly check.

17. ESP housings - assembly.

18. Cranes with lifting capacity over 100 tons - assembly of structures and individual units.

19. Swing mechanisms for excavators, loaders, portal cranes - control assembly.

20. Dryer nozzle - installation into the housing.

21. Samples of simulators intended for training workers (crane operators and lifters) - manufacturing, assembly, adjustment and testing.

22. Technological equipment intended for the manufacture, assembly and testing of prototypes - manufacturing.

23. Furnaces for heat treatment - parts manufacturing and assembly.

24. Open-hearth furnaces - assembly of metal structures.

25. Plates of automatic filter presses - assembly.

26. High pressure heaters - assembly.

27. Reactors, autoclaves, multi-chamber tunnel dryers - assembly.

28. High pressure tanks - assembly.

29. Elevator body sections - assembly.

30. Suction dredgers and installations with a capacity of up to 300 cubic meters. m / h - assembly.

31. Composite racks, chairs and armchairs with movement in three planes - manufacturing, assembly, testing.

32. Excavator trusses A-shaped - general assembly.

33. Automatic filter presses - general installation.

34. Tanks - assembly.

35. Walking excavators of high power - assembly.

§ 143. Locksmith for the assembly of metal structures of the 6th category

Description of works... Assembly, adjustment, testing and delivery in accordance with the technical conditions of complex metal structures, as well as experimental and unique units of metal structures that require increased accuracy of assembly work. Construction of complex geometric shapes from assembly diagrams and sketches. Participation in the preparation of a passport for the assembled units of metal structures. Hydraulic and pneumatic testing of experimental and unique units of metal structures operating under pressure. Verification of the correct assembly of metal structures of varying complexity with the removal of operational diagrams and characteristics.

Must know: basics of heat engineering, mechanics, geometry and trigonometry; principle of operation and rules for the operation of complex metal structures; equipment, complex tools, fixtures and various devices used in the assembly of metal structures; the sequence of assembly of metal structures; requirements for the assembly of structures and products subject to special tests; technology and technical conditions for the assembly of metal structures.

Work examples

1. Autoclaves, recuperators, muffleless, tempering and hardening units - manufacturing of units and installation.

2. Heat exchangers of complex design - manufacture of pipe systems, general assembly, installation and testing.

3. Blast furnace casings, air heater domes, blast furnace inclined bridges - control and enlarged assembly.

4. Supports of heavy power lines - control and enlarged assembly.

5. Supports of tubular structures (telemasters, radio masts) - assembly.

6. Shells and dredging installations with a productivity of over 300 cubic meters. m / h - assembly.

7. Pipe and air ducts are circular, tangential inlets, elliptical branch pipes - assembly.

This job description has been translated automatically. Please note that automatic translation does not provide 100% accuracy, so there may be minor translation errors in the text.


Instructions for the position " Locksmith for the assembly of metal structures of the 4th category"presented on the site complies with the requirements of the document -" REFERENCE BOOK of qualification characteristics of workers' professions. Issue 42. Metal processing. Part 1. Managers, professionals, specialists, technical employees. Part 2. Workers. Book 1. "Metal casting", "Metal welding". Book 2. "Drawing, squeezing, cold stamping of metal. Production of heating boilers, metal tanks and similar products", "Forging, high and low temperature metal processing". Book 3. "Turning, drilling, milling and other types of metal and material processing", "Metal coating with metals. Painting". Book 4. "Coating metals with non-metals: enamel and other types of coating", "Locksmith and assembly work in the production of machines" ", which was approved by order of the Ministry of Industrial Policy of Ukraine on March 22, 2007 N 120. Approved by the Ministry of Labor and Social Policy of Ukraine. since April 2007 The status of the document is "valid".

Preface to job description

0.1. The document comes into force from the moment of its approval.

0.2. Document developer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.

0.3. The document has been agreed upon: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.

0.4. This document is checked periodically at intervals not exceeding 3 years.

1. General Provisions

1.1. The position "Locksmith for the assembly of metal structures of the 4th category" belongs to the category "Workers".

1.2. Qualification requirements - vocational education. Advanced training and work experience as a fitter for the assembly of metal structures of the 3rd category - at least 1 year.

1.3. Knows and applies in activities:
- technical conditions for the preparation of complex metal structures;
- a system of tolerances and landings, qualities and roughness parameters (classes of accuracy and purity of processing);
- the effect of heating metals (during welding) on their deformation;
- symbols of welded seams;
- methods of alignment of complex steel structures, rules for the establishment and structure of lifting mechanisms and devices;
- methods of straightening complex metal structures in devices using templates and drawings;
- device and rules for setting up manual pneumatic machines.

1.4. A metalworker of the 4th grade is appointed to the position and dismissed by order of the organization (enterprise / institution).

1.5. The 4th grade metalworker is directly subordinate to _ _ _ _ _ _ _ _ _ _.

1.6. The 4th grade metalwork assembly locksmith supervises the work of _ _ _ _ _ _ _ _ _ _.

1.7. A locksmith for the assembly of metal structures of the 4th grade during his absence is replaced by a person appointed in accordance with the established procedure, who acquires the appropriate rights and is responsible for the proper performance of the duties assigned to him.

2. Description of work, tasks and duties

2.1. He composes complex assemblies of metal structures for welding and riveting for assembly drawings and diagrams using universal devices, and also makes especially complex assemblies of metal structures using universal assembly and special devices and templates.

2.2. Marks the places for the installation of complex basic parts and assemblies of metal structures.

2.3. It rules complex and especially complex parts and assemblies of metal structures.

2.4. Cleans welded seams for gumming with a manual pneumatic grinder.

2.5. Takes part in the preparation of experimental and unique assemblies of metal structures under the guidance of a highly qualified locksmith.

2.6. Carries out hydraulic and pneumatic tests of complex assemblies of metal structures working under pressure.

2.7. Eliminates defects revealed after testing complex assemblies of metal structures.

2.8. Draws up sketches and assembly diagrams.

2.9. Assembles, lifts and temporarily sets up metal construction elements in different positions at different heights.

2.10. Knows, understands and applies the current regulatory documents relating to his activities.

2.11. Knows and fulfills the requirements of regulatory enactments on labor protection and the environment, complies with the norms, methods and techniques for the safe performance of work.

3. Rights

3.1. The 4th grade metalworker assembling metal structures has the right to take action to prevent and eliminate cases of any violations or inconsistencies.

3.2. A metalworker of the 4th grade has the right to receive all social guarantees stipulated by law.

3.3. A metalworker of the 4th category has the right to demand assistance in the performance of his official duties and the exercise of rights.

3.4. A locksmith for the assembly of metal structures of the 4th grade has the right to demand the creation of organizational and technical conditions necessary for the performance of official duties and the provision of the necessary equipment and inventory.

3.5. A metalworker of the 4th category has the right to get acquainted with the draft documents relating to his activities.

3.6. A metalworker of the 4th grade has the right to request and receive documents, materials and information necessary for the performance of his official duties and orders of the management.

3.7. A metalworker of the 4th grade has the right to improve his professional qualifications.

3.8. A locksmith for the assembly of metal structures of the 4th grade has the right to report all violations and inconsistencies identified in the course of his activity and make proposals for their elimination.

3.9. A locksmith for the assembly of metal structures of the 4th grade has the right to familiarize himself with the documents defining the rights and obligations of the position held, the criteria for assessing the quality of the performance of official duties.

4. Responsibility

4.1. A locksmith for the assembly of metal structures of the 4th category is responsible for non-fulfillment or untimely fulfillment of the duties assigned by this job description and (or) non-use of the granted rights.

4.2. A metalworker of the 4th grade is responsible for non-compliance with the rules of internal labor regulations, labor protection, safety, industrial sanitation and fire protection.

4.3. A metalworker of the 4th category is responsible for disclosing information about an organization (enterprise / institution) related to a trade secret.

4.4. A metalworker of the 4th grade is responsible for non-fulfillment or improper fulfillment of the requirements of the internal regulatory documents of the organization (enterprise / institution) and legal orders of the management.

4.5. A metalworker of the 4th category is responsible for offenses committed in the course of his activities, within the limits established by the current administrative, criminal and civil legislation.

4.6. A metalworker of the 4th category is responsible for causing material damage to the organization (enterprise / institution) within the limits established by the current administrative, criminal and civil legislation.

4.7. A metalworker of the 4th grade is responsible for the misuse of the granted official powers, as well as their use for personal purposes.

5. Examples of work

5.1. A-like excavator farms - the compilation of individual units.

5.2. T-shaped, box-shaped and lattice tanks for load-bearing metal structures - compilation.

5.3. Cylindrical Tanks and other vessels operating under a pressure of more than 15 to 30 MPa (150 to 300 kgf / cm 2) - drawing up and hydrotesting.

5.4. Mixer Bandages - Compilation.

5.5. Mixing drums with internal spirals - compilation.

5.6. Cell shafts of disc vacuum filters made of high-alloy steel - compilation.

5.7. Drilling towers - drawing up individual parts of the metal structure.

5.8. Gas holders, air collectors and water pipes - drawing up.

5.9. Gas pipelines - drawing up.

5.10. Auger screws - compilation.

5.11. Ties and struts - drafting.

5.12. Electric blowers and turbo blowers - drawing up.

5.13. Elements for radio towers, power line supports - drawing up.

5.14. Elevators, smoke exhausters - compilation.

5.15. Frames and casings of industrial ovens and dryers - compilation.

5.16. Turbine casing frames - drawing up.

5.17. Protective covers - assembly, installation.

5.18. Constructions of bearing bridges of pipelines - drawing up.

5.19. Conductors, copiers for farms - compilation.

5.20. Evaporator and Condenser Housings - Arrangement with spherical bottoms and weld fittings.

5.21. Cranes with lifting capacity up to 100 t - assembly of structures and individual units.

5.22. Monorail - Compilation.

5.23. Lattice supports - drawing up.

5.24. Overall welded tanks - drawing up.

5.25. Dryer nozzle sections - compilation.

5.26. Traverses are assemblies for welding.

5.27. Half-timbered houses - drawing up girders and elements.

5.28. Blast furnace refrigerators and tilting machines - fabrication and assembly.

5.29. Cabinets and drawers (waterproof) - compilation.

Job description
locksmith for the assembly of metal structures of the 4th grade [ name of company]

See Help on the topic: "Job descriptions for managers, specialists, workers and the procedure for compiling them" and the List of job descriptions by divisions of the enterprise and industries

This job description was developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Tariff and Qualification Reference Book of Work and Professions of Workers, Issue 2, sections: "Foundry work", "Welding work", "Boiler houses, cold stamping, drawing and pressure works" , "Forging and heat works", "Mechanical processing of metals and other materials", "Metal coatings and painting", "Enameling", "Locksmith and fitter-assembly works", part 2, sections: "Mechanical processing of metals and other materials "," Metal coating and painting "," Enameling "," Locksmith and fitter-assembly works ", approved by the resolution of the Ministry of Labor of the Russian Federation of 01.01.2001, N 45; The list of industries, workshops, professions and positions with harmful working conditions, work in which gives the right to additional leave and a reduced working day, approved by the Resolution of the USSR State Committee of Labor and the All-Union Central Council of Trade Unions Presidium of 01.01.2001 N 298 / P-22; Order of the Ministry of Health and Social Development of the Russian Federation of 01.01.2001 N 543n "On Approval of the Model Norms for the Free Issuance of Certified Special Clothing, Special Footwear and Other Personal Protective Equipment to Housing and Communal Services Employed in Work with Harmful and (or) Dangerous Conditions labor, as well as work performed in special temperature conditions or associated with pollution "; Order of the Ministry of Health and Social Development of the Russian Federation of 01.01.2001 N 1104n "On Approval of the Model Norms for the Free Distribution of Special Clothing, Special Shoes and Other Personal Protective Equipment to Workers of Machine-Building and Metal-Working Industries Employed in Work with Harmful and (or) Dangerous Working Conditions , as well as at work performed in special temperature conditions or associated with pollution ", and other regulations governing labor relations.

1. General Provisions

1.1. A metalworker of the 4th category belongs to the category of workers and is directly subordinate to [ name of the position of the immediate supervisor].

1.2. A person with secondary vocational education and work experience in the specialty of at least [ meaning] years old.

1.3. A metalworker of the 4th grade is appointed to the position and dismissed from it by order [ name of the manager's position].

1.4. A metalworker of the 4th grade should know:

The name and purpose of locksmith and measuring tools and devices and their application;

Methods for refueling locksmith tools;

Techniques for performing simple and medium-complexity locksmith operations and the process of assembling simple and medium-complexity metalwork assemblies;

Arrangements and rules for the operation of lifting and transporting devices, working and measuring instruments and devices;

Technological process, methods and techniques for assembling, fitting, checking and straightening metal structures;

The system of tolerances, landings and their designations in the drawings;

Properties, grades and assortment of materials and pipes used;

Ways of joining parts for welding;

Rules and types of marking of assembled units;

Methods for marking places for the installation of basic parts and assemblies of metal structures;

The constructive arrangement of the devices used in the assembly;

Methods for sharpening locksmith tools;

Rules for working with a gas cutting machine and an electric welding machine;

The sequence and methods of assembly on assembly racks and by conductor-copiers;

Assortment and steel grades;

Specifications for the assembly of complex metal structures;

Qualities and roughness parameters;

Influence of heating metals (during welding) on their deformation;

Symbols of welds;

Methods for aligning complex steel structures;

Installation rules and arrangement of lifting mechanisms and devices;

Methods for straightening complex metal structures in fixtures using templates and drawings;

The device and rules for setting up manual pneumatic machines;

Fundamentals of Labor Law;

Internal labor regulations;

Sanitary and personal hygiene rules;

Rules and regulations of labor protection, safety and fire protection;

Rules for the use of personal protective equipment;

Requirements for the quality of work (services) performed;

Requirements for the rational organization of work in the workplace;

Types of marriage and ways to prevent and eliminate it;

Industrial signaling.

2. Job responsibilities

The following job duties are assigned to the 4th grade metalwork assembly fitter:

2.1. Manual chopping and cutting of wire, sheet and section metal blanks.

2.2. Sawing and deburring.

2.3. Assembly of complex metal structures together with a mechanic and an electric welder of a higher qualification.

2.4. Manufacturing of simple parts from bar and sheet metal.

2.5. Part marking using simple templates.

2.6. Driving and cutting threads manually with taps and dies.

2.7. Alignment of assembly racks.

2.8. Installation of bolts and studs in the matching holes of metal structures.

2.9. Assembly of simple assemblies of metal structures for welding and riveting according to drawings and sketches using universal assembly and special devices.

2.10. Tacking parts during assembly by electric welding.

2.11. Drilling, reaming and reaming of small parts holes according to the markings on the machine and portable power tools.

2.12. Editing of parts and assemblies of metal structures, regardless of complexity.

2.13. Assembly of metal structures, regardless of the complexity for welding and riveting according to drawings, sketches and assembly diagrams using universal fixtures, as well as assembly of complex metal structures using universal assembly and special fixtures and templates.

2.14. Adjustment of sealing surfaces.

2.15. Marking of places for the installation of basic parts, regardless of the complexity and nodes of metal structures.

2.16. Hydraulic and pneumatic testing of metal structures, regardless of the complexity, working under pressure.

2.17. Cleaning for gumming of welded seams with a manual pneumatic grinder.

2.18. Participation in the assembly of experimental and unique assemblies of metal structures under the guidance of a more highly qualified locksmith.

2.19. Elimination of defects discovered after testing complex assemblies of metal structures.

2.20. Drawing up sketches and assembly diagrams.

2.21. Assembly, lifting and installation with temporary distribution of metal structures in different positions at different heights.

2.22. Leading workers of lower grades of the same profession.

2.23. Execution of work on acceptance and delivery of the shift, cleaning of the workplace, devices, tools, as well as keeping them in proper condition, maintaining the established technical documentation.

2.24. [Other job responsibilities].

3. Types of work

The 4th grade metalwork assembly locksmith performs the following types of work:

3.1. Cylindrical tanks and vessels operating under pressure up to 30 MPa (up to 300 kgf / sq. Cm) - assembly and hydraulic test.

3.2. Sheet and strip steel parts - template marking, straightening.

3.3. Sheet steel parts - bending.

3.4. Parts made of section steel of all profiles with a thickness of up to and over 6 mm - cutting, chopping.

3.5. The details are different - filing free sizes, cutting at corners, drilling according to the marking.

3.6. Small-sized casings - assembly.

3.7. Caps, lids, brushes, vessels, funnels, boxes, cabinets of all sizes - preparation, straightening and assembly of parts for welding.

3.8. Sheet and profile metal - drilling, cutting with guillotine and press-shears, joining for welding.

3.9. Strip and twisted metal - bending and stripping after flame cutting.

3.10. Butt pads, stiffeners, temporary bolts - installation.

3.11. Supports and frames for apparatus - assembly.

3.12. Simple and complex gaskets made of sheet steel, cardboard, asbestos, clinoherite, rubber - cutting and cutting by hand.

3.13. Staples made of material of different cross-sections - flexible in the device.

3.14. Welded racks - assembly for welding.

3.15. Belt conveyors - assembly of metal structures.

3.16. Pipe fittings with flanges - assembly.

3.17. Metal cabinets and shelves - assembly.

3.18. Low pressure washers with detachable connections - assembly.

3.19. Oil tanks - production and assembly.

3.20. I-beams for monorails - assembly.

3.21. Baths of rolling equipment and oil gearboxes, casting ladles of various capacities - assembly for welding.

3.22. Manifold Insulation - Parts Manufacturing and Assembly.

3.23. Plate and overhead conveyors - assembly of metal structures.

3.24. Door and window frames and metal doors with a rigid frame - assembly.

3.25. Counterweight bodies - weld assembly.

3.26. Ladders, platforms, purlins, bunker walls, flooring, metal railings made of pipes and tees, brake sheets, fences, sliding supports, gratings - assembly.

3.27. Cylindrical and tapered shells made of sheet metal - bending.

3.28. Sediment tanks, measuring tanks, collectors - assembly.

3.29. Foundation slabs - assembly.

3.30. Louvered grilles, floorings for openings, bar posts for fixing conductors, conductor for anchor bolts - assembly.

3.31. I-section rods - assembly of metal structures.

3.32. Farms - copier assembly.

3.33. A-shaped excavator trusses - assembly of individual units.

3.34. T-shaped, box-shaped and lattice tanks for load-bearing metal structures - assembly.

3.35. Mixer bands - assembly.

4.2. For additional vacation.

4.3. For the free distribution of special clothing, special footwear and other personal protective equipment.

4.4. Payment of additional costs for medical, social and vocational rehabilitation in cases of damage to health due to an industrial accident and an occupational disease.

4.5. Require the creation of conditions for the performance of professional duties, including the provision of the necessary equipment, tools, a workplace that meets sanitary and hygienic rules and regulations, etc.

4.6. Require the management of the enterprise to assist in the performance of their professional duties and the exercise of rights.

4.7. To get acquainted with the draft decisions of the management of the enterprise concerning its activities.

4.8. Improve your professional qualifications.

4.9. Other rights provided for by the labor legislation of the Russian Federation.

5. Responsibility

A metalworker of the 4th grade is responsible for:

5.1. For non-fulfillment, improper fulfillment of the duties provided for by this instruction - within the limits determined by the labor legislation of the Russian Federation.

5.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.

5.3. For causing material damage to the employer - within the limits determined by the current labor and civil legislation of the Russian Federation.

The job description is developed in accordance with [ name, number and date of the document].

HR manager

[initials, surname]

[signature]

[day month Year]

Agreed:

[position]

[initials, surname]

[signature]

[day month Year]

I have read the instructions:

[initials, surname]

[signature]

[day month Year]