Do-it-yourself fan from a cooler and a disk. We make a USB fan at home with our own hands Making a fan with our own hands

Very often in the sultry heat in the room there is not enough at least a minimum air flow. To solve this problem, many people buy desktop fans, they are convenient and compact, some of them are powered by USB, that is, they can be connected to any charger, power bank or laptop so that the coolness is always with you. But why buy something that you can make yourself from improvised means? For readers of the site, we have prepared two simple instructions that will clearly explain how to make a USB fan at home with your own hands. So, all you need to prepare is a sharp knife, good scissors, electrical tape, an unnecessary USB cable and, in fact, a homemade executive body. As for the latter, it is customary to use one of two options here: an old cooler from a computer or a motor from a typewriter or other toy.

Idea #1 - Use a cooler

It will take no more than 15 minutes to assemble a USB fan from a cooler. First you need to prepare the cooler. Two wires come out of the device - black and red, and sometimes yellow, even more rarely - blue. Yellow and blue are not useful to us. We clean the insulation by 10 mm and put the prepared element aside.

Next, you need to prepare the USB cable. We cut off one half of it and in the place of the cut we clean off the insulation with a sharp knife, a clerical one is perfect. Under it you will see four wires, of which two are necessary: ​​red and black. We also clean them, while the other two (usually green and white) are best cut and insulated.

Now, as you understand, it is necessary to connect the prepared contacts in pairs, according to: red with red, black with black using twisting. After that, you need to carefully insulate the cable junctions with electrical tape or heat shrink and make a stand. As for the stand, it's up to your imagination. Someone successfully uses wire, others are very interesting in cutting out a landing nest in a cardboard box.

In the end, a homemade mini fan is connected to a computer or charging box, and you can enjoy the operation of your own electrical appliance.

Cooler idea

Idea number 2 - Use a motor

In order to make a USB fan from a motor and a CD, it will take a little more time, but still, in an hour you can easily make such an electrical appliance with your own hands. A motor for such a homemade product should be chosen with an operating voltage of about 5 volts, maybe a little more. If you take the motor to a lower voltage, then too much current will flow through the circuit and the motor will quickly fail.

First, we prepare all the elements of the device. In this case, you will need to make an impeller (blades).

To do this, we recommend using an ordinary CD. We draw it into 8 equal parts and carefully cut it with good scissors, almost reaching the center. Next, we heat up the disk (it is convenient to do this with a lighter), and when the plastic becomes more elastic, we bend the blades at an equal angle (as shown in the photo).

If the impeller is not bent enough, then no air flow will be created during the rotation of the disk. However, if you overdo it, then homemade will also work poorly and unstable.

When the blades are ready, proceed to the creation of the main mechanism. Inside the disk, you need to insert an ordinary, cut to the desired size, champagne cork, which must be mounted on the motor shaft. Next, we move on to creating a USB fan stand for a laptop.

Here, as in the previous version, it all depends on your imagination. Of all the tools at hand, the wire option is the most suitable. When the homemade USB fan is ready, we connect the wires of the motor to the wires of the usb cord, as in the previous version, carefully isolate the twist and proceed to the tests.

The weather is getting warmer outside, it's time to think about ventilation. In this issue, Roman Ursu will be making a bladeless fan. You can easily repeat this product with your own hands. Four pieces of cardboard are used in the product. The width must match the width of the cooler. 120 mm. A switch and a power connector are built into the housing. We will measure and make a hole according to the desired diameter. You will also need a 12 volt cooler power supply that consumes 0.25 m. A 2 amp unit, so that's enough. The top of the Dyson fan is cylindrical. This means that we draw two circles with a diameter of 15 cm. In one of them 11 cm, in the other 12 cm. To keep the parts well on the base, we take one of the walls, apply the parts, draw a line and cut it off. Now, in order to form the cylinders, you will need three segments with the following dimensions: 12 x 74, 12 x 82, 15 x 86 cm. We will figure out what and where to glue at the assembly stage. Let's make cuts in each wall. These will be the air channels. They look like good legs.

Let's start assembling a bladeless beautiful fan by placing the courier in the middle. Glue each wall one by one. The wires can be removed as shown in the video. It would be nice to figure out the connection. We use the switch, so we separate one of the wires and form a circuit. The wires go to the power connector, black to minus, red to plus.

It is necessary to connect all the previously prepared parts with your own hands. We take a ring with an inner diameter of 11 cm. It will be in front. And a segment 12 × 74. We connect, as in the video.

We repeat the same with the second ring and the 12 x 82 blank. To keep the fixed rings stable, we use five small baffles of strength. The length is slightly less than 12 cm. It remains only to close the structure.

We use the last segment 15 x 86 cm.

In conclusion, we bring beauty, remove excess glue, cover with paint. In general, the bladeless fan is ready.

There are a lot of useful homemade products ahead, we are waiting for the warm sun to shoot the next video and show it on the channel.

The fan is not a complex device. It consists of a motor, blades, various adjustment buttons and a stand-case. There are additional elements, such as backlight, clock, but these are already options that are not so important.

It is not at all necessary to buy a fan, because it is quite possible to make it yourself. Moreover, this does not require special skills of the master.

With the proper skill, a home-made model will turn out not to be a way to get rid of old things, but an opportunity to show imagination and, possibly, hidden talents. Some craftsmen quite simply get both functional and extremely attractive options. They harmoniously complement the interior and become the center of attention no worse than any art object.

How to make a fan from a conventional electric motor

Probably the easiest and fastest way to get your own homemade fan assembly is to find a regular motor, which is most often found in toys.

Standard electric motor from a toy

Ordering such a thing is not difficult. Moreover, today, without stopping for a minute, caravans of various knick-knacks from the Celestial Empire ply. And if not, then it’s enough to buy an inexpensive toy car and remove the motor from it.

But expect the impossible from such a device is definitely not worth it. Rather, it can only slightly drive air. But for a desktop model it will do. He will be able to blow the face of the person sitting at the computer.

For such a fan, you can use absolutely anything. The main parts will be:

• blades;
• motor;
• on/off button;
• stand;
• supply system.

Otherwise, the limit of the idea will be only within the boundaries of fantasy.

After the motor is ready for use, it makes sense to take care of the power. These can be batteries, as in the toy for which the motor was intended. But, of course, such energy will not last long. However, there is a plus - the device will remain compact and mobile.

The second option is mains power. But in this case, don't overdo it. Direct connection through the plug is a sure way to burn out the motor. So do not experiment, trying to spin the engine up to high speeds. On toys, electric motors are usually designed for 3-4.5 Volts, and the desire to give more rotation due to powerful energy sources, firstly, will quickly land the source (if it is a battery), and secondly, it will seriously reduce the life of the fan up to breakage. The motor will start to heat up, the brushes may melt.

But modern chargers convert the voltage in the network, reducing it to the specified parameters. You can find a power supply, including on sale, which is ideal for the motor.

To create the blades, you can already take any material. The main thing is that it should be light. Due to the weakness of the motor, the less the blades weigh, the faster the rotations will be, and, therefore, the efficiency of the work.

• The easiest option is to take a cork from an ordinary plastic bottle, which will serve as a fastener for the blades. Make a hole in the bottle according to the size of the rotating axis of the electric motor.
• Blades can be made from a regular CD. A hole is burned in the center according to the size of the cork from the bottle. The circumference of the disk is divided into 8 sectors. They are cut for some distance, but not to the center. After that, the disk must be heated with fire in order to easily bend the blades. For this, a lighter is suitable.

Creating Blades on CD

• You can attach the disc to the cork with glue. The second option - when a hole is burned in the middle for the cork - immediately connect the structure. The melted plastic will harden and hold firmly.
• After all this, the structure is interconnected. Wire is suitable for the stand. This is perhaps the easiest option. And for such a light device, you can’t imagine better. You can bend the skeleton in such a way as to discreetly hide the batteries there. Or carefully run the power supply wire going to the motor.
• The circuit should not always be closed if batteries are used, so a button must be fixed on the case. She is inexpensive. You can use it from the toy from which the motor was removed.

Another version of the propeller device is the use of paper, only thick. The method is even simpler, but less practical.

Advice! When experimenting, remember that the larger the fan blade area, the more noisy it will be. On the other hand, small blades do not move air as efficiently.

How to make a paper fan

Paper is not the best material for a home fan for the simple reason that it is very impractical. Any ingress of water, even banal humidity - and the device will rapidly begin to lose its rigidity.

But even despite all the disadvantages, craftsmen even make quite nice samples from paper. Of course, we are talking about thick paper or cardboard. Strong material from boxes is good. A regular motor or cooler, an on / off button and wires are also useful.

The simplest table fan using cardboard

An approximate design plan is that the device can be simplified as much as possible. The impeller is easy to cut and can have many or few blades. All at the request of the master. The motor can be mounted on a wooden or cardboard bar. The stand will also go from paper or an old computer disk.

It is only important not to forget that such a fan turns out to be very light, which makes it shaky in operation. Therefore, it is necessary to further strengthen the body. Old batteries, bolts or nuts are good.

How to make a plastic bottle fan

Crazy Hands' favorite raw material - plastic bottles - are almost ideal for creating your own fan. For a propeller, the top of a standard round bottle works well. It is necessary to cut off the part with the cork just above the glued label.

• The part of the bottle with the cork will be the blades. To do this, the plastic before the cork needs to be cut so that several different petals are obtained. After one, the petals are cut off at the base. The rest are the future propeller blades.

Plastic bottle fan blades

• To shape the blades and twist them a little, you can use a candle or a lighter. The main thing is not to overdo it, because the plastic is soft and can catch fire. The task is to warm it up a little, and not set it on fire.
• The cork will be the base of the propeller. A hole is made in it according to the dimensions of the axis of the motor. To keep the connection firmly, you can put it on glue.
• Now is the time to think about the foundation. The rest of the plastic bottle is also suitable for it. A hole is cut in it to firmly place the cork with the blades at a right angle. It is necessary not to forget to weight the base - with nuts, bolts or any other metal objects.
• A hole is made on the base for the button and the chain is assembled. There is also enough space for the power supply.

The field for imagination when working with a plastic bottle is extensive. You can use several bottles at once. One will become a propeller (more precisely, part of it), and the second will become a good base. But then additional materials will be needed. For example, regular drinking straws.

Simple and lightweight bottle fan

How to make a usb fan

But the most convenient and simplest fan is exactly the old cooler, which can also be used. For example, put it on the table, and it will cool, only not the processor or video card, but the person.

The advantages of this design are obvious: the cooler is very reliable, because it is his job to constantly turn the impeller and cool something. Yes, and getting coolers is easy. It is enough to either find an old computer, or order a new fan or buy it in a store.

The cooler device is simple. This is a ready-made fan in a plastic case. Two wires (usually red and black) depart from it.

Regular computer cooler

Making a USB fan is a matter of minutes:

1. The wires on the cooler are stripped by 1-2 centimeters.
2. A regular USB cable is taken, at the end of which you also need to get rid of the insulation. The standard USB cord has four wires inside. Of these, you should choose black and red. Cut off the rest so as not to interfere, and clean up the necessary ones.
3. Connect the red wire of the cord to the red one on the cooler. Black - with black. Carefully insulate areas without winding. Ready.
4. It remains only to think about the holding device. Here the already familiar wire, which takes any shape, can come in handy. Even a cardboard box will do for the fan case, and if you spend a little more time and effort, you can even build a real design object.

Design approach to the design of the fan

It is very convenient when the fan turns on when you start the computer. In addition, modern blocks have several USB outputs at once. It turns out that such a device will not interfere.

Another point - sometimes you want to turn on the fan regardless of the computer's operation (especially since a device with a cooler turns out to be quite powerful, good and useful). Then you can use adapters. For example, phones today make chargers that easily turn into a USB cord when the plug is disconnected. Similar equipment can also be used for a fan, making it universal: powered from the network and from the USB port of any computer. Another plus of this design is the simplest electrical circuit. A cooler-based fan can even do without extra buttons: just a wire and a plug.

DIY bladeless fan

But a slightly uncommon use of a free cooler (but you can get by with an electric motor) is a bladeless fan. Modern, interesting, with due skill - no less effective - a solution that definitely attracts the eye. The thing turns out to be completely non-standard, spectacular.

For example, here is the ideal appearance of a bladeless or ducted fan model:

This is how you can make a bladeless fan with your own hands

The most important thing about bladeless models is, of course, their appearance. Therefore, if you make such a device yourself, then you need to try to think through the frame in great detail. Rough edges, roughness - all this will spoil the impression.

The case of a bladeless fan is almost entirely a working area. Do not think that some space technologies are implemented here.

Air circulation is carried out quite prosaically - with the help of rotating blades. They hide in a tuba base. If you take a cooler from a computer, then you can make a stand according to its shape. Here, as they say, at the discretion of the author.

The differences from the classics are in the location of the cooler - it is placed horizontally in a bladeless fan.

Location of the cooler in a bladeless fan

The upper ring is made hollow inside, two-layer. There, the main redirection of air in the right direction is carried out.

A hollow cavity is visible in the upper ring of the fan, from where air blows

You can make the frame of a bladeless fan out of plastic, wood, thick cardboard. It is better to use a flexible material so that it can be easily shaped into a ring. Alternatively, use a combined structure. For example, rings are made of cardboard or plastic, and the frame is rigid - made of wood.

You need to cut out:

• four faces for the stand;
• Two circles of the same radius;
• Twist two rings of different diameters.

Then everything is connected together, if necessary - painted.

Meals can be organized in different ways. A universal option - a combined cable for a USB connector and a plug-in plug for an outlet.

The device can also be slightly complicated. For example, make a light strip from a diode tape along the edge of the rim. The backlight consumes little energy, but it will add beauty to the fan. And the power supply and wiring, if necessary, can be easily hidden in the stand.

How to make a powerful fan with your own hands

When it comes to powerful fans, you need to understand that they require completely different motors. Starting from the motors of old fans, ending with other household appliances. Well suited:

• unnecessary ceiling chandeliers with a fan;
• old lawn mowers;
• drills;
• hoods.

The only thing you need to get into the voltage corridor, which is required to power the motor. For example, drills most often need 18 volts. But for ventilation purposes, it will be sufficient to supply less than half of this voltage. Even at 12 volts, the fans are very loud and extremely unstable due to the strong inertia of the rotating blades.

Power for powerful electric motors must be done from the network. Therefore, you need to think about installing a power supply or connecting a charger. The wiring diagram can be complicated by adding light bulbs, an electronic clock, a radio, a toggle switch or a board for switching operating modes. But it's easier, of course, to limit yourself to only a fan with a button, if that's enough.

In any case, such homemade variations of homemade fans are sometimes much better than even purchased options. With proper skill, a very good thing can turn out, the real pride of the owner.

Summer has come, which means heat, heat and an eternal lack of coolness. But this problem is fixable, and pretty easy. You only need a few details and some free time to make your life easier with your own hands, fill it with light coolness, which you will certainly get by making a USB fan at home. Of course, you can go and buy a fan in the store, but how nice it will be to sit near the same computer, and a light breeze will blow on you from the USB fan you created. And a thing created by one's own hands always pleases not only the eye, but also develops selfishness.

We offer you to watch a homemade video - usb fan:

Tools for usb fan:
- Regular CD (not necessarily new);
- A tube of silicone glue is empty;
- Wooden block;
- Mini disk;
- USB cable;
- Motor;
- Holder;
- Adapter;
- Silicone glue gun.

Three holes must be made in the tube, one in the lid, and two on the sides. Holes are easy to make using a regular nail, which must first be heated.

It is also necessary to make a slot or recess in a wooden block. This can be done easily with sandpaper.

The mini disk easily turns into a propeller. To do this, it must be drawn into uniform blades, then heated with a clerical knife and cut along pre-drawn lines. And after that, we heat the base of each blade with a lighter and with the help of our hands we bend each blade a little to make a propeller.

We take the motor, holder and adapter from a non-working CD drive.

Now let's start assembling the USB fan.

Heat up the glue gun. Lubricate the holder along the axis with silicone glue from a glue gun. The propeller must be firmly planted on this glue. Press on all sides. Then, on the other side of the holder, we drip a drop of glue and glue the adapter. We are waiting for the glue to dry well. This usually only takes a couple of minutes.

Now we take a tube of silicone glue, remove the lid and grease the inside with silicone glue. And inside we insert the motor so that the part that we will connect sticks out of the hole that we originally made.

Then we put the USB cable into the side hole of the glue tube and connect the ends of the wires to the motor.

It is necessary to pour silicone glue into the recess in the wooden bar, and put the wire from the USB cable tightly there, and glue the tube with the motor inside to the base of the bar. And on the other side of the bar, glue the CD on silicone glue.

Now the propeller must be mounted on the side of the adapter glued to it on the sharp edge of the motor, which sticks out of the hole in the glue tube.

And finally, our USB fan can be plugged in and get that long-awaited coolness.