How to unscrew the thorough screws. He placed an elastic band on a damaged screw. This ingenious trick is useful to everyone! NO3 option. Unscrew the screw with the TORX slot

To unscrew the screws with torn edges on a hat in several ways.

• If the hat is performing, then you can try to make a neat inscribed in its middle part, using conventional knife In terms of metal, after which you try to unscrew the screw to the usual flat screwdriver. But unfortunately not always a hat may be higher.
• If the faces in the hat are not completely jammed, then you can try to pick a flat screwdriver (or sharpening it on the sandpaper circle) so that the edges of the screwdriver's working edge tightly cling to the rest of the faces in the screw of the self-press.

If the two ways described two ways did not help, then only surgical intervention remains. We will need drill and drill. The algorithm of our actions will be:

• Method first. Jewelry. The thin drill is deepened in the center of the screw, after which it inserts into the resulting hole sharpened under the rectangular profile of the carnation and bending it, trying to unscrew.
• The second way. Radical. We select the drill with a diameter with an equal diameter of the cap and completely drill it to such an extent until the pressed by this screw is done, it will not be possible to remove. After that, our self-tapping screw adds in a natural way in length and a wonderful opportunity appears to grasp it with pliers.

This is certainly far from the only ways, but as practice has shown the most effective. Someone glide on a hat piece cold welding and already to her lever, after which he twists, but this method Unreliable if your self-tapping screw in dense matter, such as an oak board.

Instruction

For a start, try still to get a self-tapping screw with a conventional screwdriver - with the assistance of the nickname, crush the groove under the straight slot of the screwdriver and try unscrew the item. If it does not work, - do not dilute too much, it will only aggravate the position. Use other methods.

If the case is not entirely running, then you can try the next simple way method - select drill drill, the diameter coincides with the thickness of the self-press. And drill it until the hat is separated from the leg. It is necessary to do it very carefully, since it flies at this moment metal chips Very small and actively strives to get into the eyes. Be sure to use special safety glasses! Many masters urgently advise the tagging of the spiers, noting its high functionality and efficiency even in the most difficult cases.

After the part holding the screw will be eliminated, it will only be left to pull the leg from the base. It is possible to do this with the help of clutter or simple pliers.

If the diameter of the self-press allows, it is possible to use a different effective, but also a very time-consuming option. To do this, drill on the axis in the screw hole, sufficient to insert the carnations into it or any friend a thin and rigid metal part. After that, carefully take it half into the well-done hole. Generate and, again, carefully, start unscrew the screw. In this case, be prepared for spending a considerable time - Jewelry work.

In case the screws rusted, use WD 40 is a means that allows and remove excess moisture. Just pour her inexpensive detail and, if possible, try it to stir up to improve the penetration of the substance between the screw and the basis. After about half an hour, try to unscrew the screw. At the same time, keep in mind that the surface that was degreased WD 40, it is necessary to lubricate it later. Otherwise, corrosion and, accordingly, the destruction of the part cannot be avoided. Therefore, use this tool only for the similar problems described, as well as to remove moisture with mechanical surfaces Details and appliances.

In the article, we will look at how to twist the screw or self-tapping screw from the wall or from another design, if it sits in it tightly, and does not give in to the twisting.

1. If with a screwdriver, screw or self-screwing is not twisted, and the screwdriver begins to scroll into the screw of the self-press, then stop and do not try to unscrew it, since you can disrupt the verge of a screwdriver in self-build, and then it will be even more difficult to remove it from the design.

2. We take a screwdriver and press up with an effort on the back of the handle of the screwdriver, try to twist the self-tapping screw, making movements, then to the left, then right. If it is impossible to remove the self-tapping screw out of the design, then go to another method.

3. We take a special screwdriver, which has a hexagon under the back of the handle wrench. By pressing the screwdriver with the power of the screwdriver, we begin to turn it with a wrench.

4. To unscrew the screws, you can use the nozzle "screw of the eco-etractor", as it completely captures all the edges of the self-building. For better adhesion of the ecotractor with a self-tapping screw, use a cleaning agent, like "pemoxol", applying it to an ecotractor.

5. If the self-sufficiency does not succumb, then we do it as follows. By inserting a screwdriver to the self-tapping screw, we apply a hammer blow on it, thereby weakening the grip of the self-drawing with the design. The main thing is not to overdo it with impact, since if the wall made from the plasterboard, then you can break it. After applying shocks on a screw, we try to twist it with a screwdriver.

6. We take thin rubber, and with a screwdriver insert it into the slot of the self-press, as the rubber fills all the space between the screwdriver and the self-tapping screw, after which they are trying to turn it out of the design.

Recently recently repaired the door and encountered a question to unscrew the screw with the torn head and here I share the experience.
I needed to remove the Drew, without disassembled her box and save the loops in place, then everything was going to place. The door was planned to handle, sand up to the tree and paint again to upgrade and give a decent appearance. All the same 100% wooden canvas better than modern glued paper doors.

Screws B. door loopsOf course, the paint was smeared, they did not want to get out and the edges on them, or rather crosses, I disadvantaged ((((
Only a few screws were filed, the others kept on the spot as the inscuffed.
In general, I noticed that the old "Soviet" screws of the Hats are broken down "at times." In addition, on time they are covered with corrosion and grip with a tree becomes almost monolithic.
So, the challenge how to unscrew the screw with the torn head - with torn edges on the Hat.
- The easiest option (if it were not necessary to put the door to the place or it was possible to move the loops on the box) it drill the hats and remove door leaf. Then climb the nippers of the hemp screws and try to unscrew them. If this option does not come out) - to bite / cast / score the remnants leaving the thread on the spot. The loop is a little shifted and everything would be "in the openwork"
But it did not come true. Became to think.
Take a grinder with a thin circle and start working.
Moreover, it was not necessary to cut crossfosters, just one drank under a direct power screwdriver.
Here is a small recipe how to unscrew the screw with a torn head in uncomfortable places. If you remember, it will be useful. Just try not to trim the whole head 😉

Ecology of life. Lifehak: when carrying out repair or construction work It often happens with your own hands that you need to unscrew the screw, which is breaking the face, and the screwdriver turns about an attempt to extract it. In such cases, you can do the following ...

When repairing or construction work, it is often with your own hands that you need to unscrew the screw, which has breakdowns, and a screwdriver turns about an attempt to extract it.

In such cases, you can do as follows:

Removal screw

Remove the screw if the head is finally torn, in several ways:

• If the diameter of the bolt allows you to drill it with a drill with a suitable drill.
• If you take a smaller drill, you can drilled hole Place a clutterned nail and unscrew the screw.
• If you need to unscrew little screw, You can drop on it superclosure and put a screwdriver. After soaring glue, you can try to unscrew it. Similarly, liquid nails can be used.
• If the size and material in which the screw is screwed up, allows you to use welding, then you need to weld the nut on top, and then unscrew.
• On a large screw, you can cut the slot with a knife and unscrew the screwdriver.

If the head is disrupted not to the end, you need to very gently heat the screw so as not to damage the material into which it is screwed, then try to extract it.published