Timber house owner reviews: turnkey and box for assembly. Timber house owner reviews: turnkey and pre-assembly box Why thin timber is used in construction

According to experienced carpenters, the construction of houses for year-round use should be made of wood with a cross section of at least 200 mm, and mandatory insulation on one side. Therefore, a house made of timber 100 × 150 mm should be subjected to maximum protection from the cold during construction, otherwise there will be no comfort in operation, and besides this, there will be a large overspending of energy resources, which is unprofitable in economic terms. What are the advantages of a thin beam, and what disadvantages will cause the structure to decline - more on that below.

Why thin timber is used in construction

There is only one reason - the price of large sections is significant. In addition, when construction is carried out by one person, the line is much easier to lift than with an increase of 10 cm along the entire length.

Also, this timber is used in the design of the truss system of large two-story objects, and a frame house made of timber 100 × 150 mm is, in general, a common solution. What are the other advantages of small-section wood:

1. It will shrink faster.
2. You do not need a monolithic foundation for a house made of light timber.
3. Work can be carried out by one person if the project is simple and does not involve the use of machinery.
4. It will take less protective compounds to impregnate wood.

That's actually all the pluses. And the cons are much more significant:

Due to the above shortcomings, thin wood is used mainly for non-responsible structures - one-story baths, outbuildings, gazebos, terraces. If, nevertheless, the owners strive to get housing from small-section wood, then frame housing construction will be the best option. How to arrange a house frame from a 100 × 150 timber with your own hands, below.

Wooden frame advantages and disadvantages

First of all, this is saving on solid wood. It is present only in the critical nodes of the structure. About everything in more detail:

• In terms of heat preservation, such a house made of timber 100 by 150 mm is not inferior to a log house. This advantage is given to him by a layer of polystyrene insulation - 5 cm of polyurethane replace 30 cm of brickwork.
• Fast construction - everything takes about 1.5 months, subject to the work of the brigade. Independent work can take away the summer period.
• The ability to hide communications in the walls, which will further simplify the selection of the interior.
• There is no shrinkage - finishing work can be started immediately.

But the cons are serious:

But, despite the shortcomings, a house made of 100 × 150 timber gets good reviews. Especially this type of construction solves the problem of housing for young families, where an addition is expected - the construction time allows you not to wait for your own corner for years.

Thin timber is a popular product of the respective manufacturers. From it build beautiful baths, cottages, gazebos, terraces. Used as a truss system and other critical structures.

However, this cannot be said about the construction of residential buildings in harsh climatic zones - for the construction of objects with a permanent location, the owners should pay attention to other products of the woodworking industry.

Rectangular bar

Doubt whether to build or not a house? It seems that the construction will hit the family budget and is it more profitable to buy an apartment? A wooden frame does not inspire confidence, and a rounded log has a high price? With the advent of various types of timber, it became possible to build a high-quality wooden house at low cost. Doubt? We will tell you how to choose a house from a bar, show the reviews of the owners, enlighten about the pros and cons. Reviews of the owners about the turnkey timber house will help you decide and convince you of the benefits of construction.

For the construction of houses, any timber is suitable: profiled or edged. For the construction of a small country house, you can use from 100x100 mm to 150x150 mm. A private residential or cottage is built using 200x200 mm. But the price of housing is a little high, in order to minimize costs, you can use the dimensions 100x150 mm, 150x200. If you use a smaller technical side, you can quickly assemble a country house, and using a larger technical side significantly reduces construction costs.

Reviews about a house made of material with a section of 100x100 and 100x150mm

Houses made of timber 100x100 are built mainly in summer cottages, since the thickness of the walls is not enough to keep warm in winter. But it takes a long time to assemble a box of material. You can reduce laying time by using a section of 100x150 mm, where the technical side will be 100 mm. Owner reviews about the construction of timber houses are mainly related to the quality characteristics of the material. Consider the most popular in the form of a table:

Characteristic	Owner reviews
	Positive	Negative
Heat loss	Housing made of glued laminated timber with a size of 100x100 built on a summer cottage, even without insulation, keeps heat well at outdoor temperatures up to + 50C.	A country house used in winter will have to be additionally insulated with mineral wool or polyurethane foam. And if the walls are hidden under the finish, then it is easier to assemble the frame. Less material will be needed.
Additional finishing	If you build from glued or profiled chamber drying, then additional finishing of the cottage is not necessary.	Construction from a simple edged material of natural moisture with a section of 100x100 mm must be finished, since a small size will not prevent cracking and twisting of the material.
Environmental friendliness	Timber structure of any section is environmentally friendly.	Glued laminated timber is not environmentally friendly enough because of the glue, and the frame structure will have to be additionally insulated. Materials for insulation are not always environmentally friendly.
The speed of assembly of the frame	It is not difficult to assemble a small country house from glued or profiled chamber-drying material with your own hands. And since the cross section is small, you can handle it alone.	It takes a long time to assemble the walls, since the cross section is small.
Shrinkage	Shrinkage in frame construction is small.	A one-piece house made of natural moisture material shrinks 10-15 cm within 3 years.

It turns out that building a large cottage with a beam of 100x100 mm is not worth it, since heat loss without additional wall insulation will be large. But for country and frame construction, the material is indispensable, since the price for it is 2-3 times lower than for a log or timber 200x200 mm.

Reviews about the house from a bar with a section of 150x150 mm

Houses made of profiled and edged timber with a cross section of 150x150 mm can be used for the construction of permanent housing only in the southern regions, since the thickness of the walls is not enough to keep warm at a street temperature of -15″C. But if you perform additional wall insulation, then housing will delight even in the coldest winters. There is another option, to build housing with glued beams. Glued lumber with a section of 150x150 mm will be equal in terms of heat-saving properties to a chamber-drying beam with a section of 250x200 mm. Consider the reviews of the owners about some characteristics of timber structures for permanent residence with a section of 150x150 mm in the form of a table:

Characteristic	Reviews about timber housing section 150x150 mm
	Positive	Negative
Heat-saving properties of walls	Glued beam house	For the construction of a permanent residence structure, the walls from a simple and profiled beam are thinner, in winter they will have to be additionally insulated.
Assembly speed	The box is assembled in 3-4 weeks.	A beam with a section of 150x150 mm is quite heavy, so it is difficult to work with it alone.
Additional finishing	A structure made of glued or profiled kiln-dried timber can be left unfinished, the walls look aesthetically pleasing.	Natural moisture will crack over time and you will have to do additional finishing.
Shrinkage	A house made of chamber drying and glued material with a section of 150x150 mm will shrink only 2-3%.	Shrinkage of natural moisture will be 10-15 cm.
Price	The price for a box made of glued laminated timber with a section of 150x150 mm is lower than for a round log.	If you do additional finishing, insulation, then the price of the structure will increase.

It is better to build a structure for permanent residence with a material with a cross section of 150x150 mm with glued or profiled chamber-drying material. You can avoid additional costs for insulation and finishing if you use a section of 100x150 mm. Moreover, if you use the technical side of 100 mm, then you can assemble a box faster as from a material of 100x100 mm, and if 150 mm, then the cost of building a house for permanent residence will be reduced, as with a section of 150x150 mm.

Reviews about houses made of timber 150x200 mm

Timber structures assembled with 150x200 material are suitable for permanent residence. They are full-fledged and retain heat well even at a temperature of -350C. Reviews about the material are mostly positive:

Characteristic	Reviews about the house from a bar with a section of 150x200
	Positive	Negative
Heat-saving properties	Keeps warm even without additional warming in the winter.	If you use profiled natural humidity, then the walls will crack over time and lose some of their heat-saving properties. And it will be difficult to perform additional caulking.
Shrinkage	Shrinkage of the walls of glued and profiled kiln-dried lumber is minimal.	Walls of natural moisture can shrink up to 10 cm.
Assembly speed	You can assemble a box with your own hands in 2-3 weeks. A turnkey house can be received in 1-2 weeks.	If you use material of natural moisture, then the structures must be settled for 1 year.
Price	The quality of the walls is the same as from a bar with a section of 200x200, and the price is lower.	The price of glued is higher than profiled or simple edged.

If you use a side of 200 mm as the technical side, then the quality of the wall will be no worse than from a beam of 200x200 mm, for the southern regions or from glued beams, houses are built making the technical side of 150 mm.

Why is it advantageous to use a rectangular section of timber

It is more profitable to use rectangular or twisted material for building houses, since the price on the market for it is lower. It’s just that for the manufacture of a square section, for example, 150x150 mm, a whole log is needed, for a section of a twisted beam of 150x100 mm, a smaller amount of raw materials will be required. So from a pine with a section of 300 mm you get 1 square beam or 2 rectangular ones. It is more profitable to use a rectangular section of a bar for building houses for a number of reasons:

1. The price of a finished box with a section of 150x100 or 200x150 is lower, and the wall thickness is the same.
2. If you fold a country house with your own hands, then the front and back sides of a larger section will allow you to use less material. Construction is faster.
3. The price for a rectangular section is lower, as it is cut from a smaller amount of wood.
4. Turnkey houses of rectangular section below.

Reviews about timber houses are positive, but when it comes to high-quality glued or profiled chamber-drying material. In other cases, it is more profitable to build a frame structure and properly insulate the walls. And using an imitation of a bar or a block house in finishing, you can achieve a visual copy of the structure from solid material. For clarity, let's compare houses made of glued profiled chamber drying and material of natural humidity in the form of a table according to quality characteristics:

Qualitative characteristics of the house	Bar of natural moisture	Profiled natural moisture	Profiled chamber drying	Glued laminated timber
The building is suitable for permanent residence	Cross section from 150x200 mm, when the technical side is 200 mm		Section 150x200 mm and above.	Section from 100x150, when the technical side is 150 mm
wall cracking	+	+	Minimum	—
Additional insulation	It is necessary to re-caulk and insulate the facade.	It is necessary to insulate the facade, re-caulking is difficult to perform.	Not necessary	Not necessary
Shrinkage first 3 years	10-15 cm	10-15 cm	3-5 cm	2-3 cm
Environmental friendliness	+	+	+	A house made of glued laminated timber is arguably environmentally friendly, since the adhesive composition can be of poor quality.
Easy assembly	If the walls are assembled with a section of more than 150x200 or more, the material is heavy.		+	+
Foundation	Simple tape, columnar, pile-screw, any lightweight, since a wooden house is light in weight.

Houses made of timber 150x100 are the cheapest option for building suburban housing. Basically, this material is used for the installation of roof structures and floor beams. However, with a high-quality finish of a wooden house, such a section is also suitable for building walls. A standard house kit made of timber 150x100 is used for the construction of a country house, and with full insulation - for year-round use.

The company "MariSrub" carries out the construction of houses from dry profiled timber with a section of 150x100 mm. It is recommended to build a cottage for permanent residence from materials grooved on the wider side. And summer cottages for seasonal recreation are best built from timber, tongue-and-groove with a narrower one.

Benefits of profiled timber

Profiled timber is a durable, reliable and environmentally friendly material with an attractive appearance. It will create an atmosphere of comfort and warmth, fill the room with a fresh forest aroma. Wood contributes to the exchange of oxygen up to 30% per day, so there will be fresh air inside the house.

In the manufacture of profiled timber, only safe materials and technologies are used, while toxic glue is used for glued timber. Therefore, the product retains the environmental friendliness and naturalness of wood.

Due to the correct geometric shape, the material is easy to customize, process and install. The assembly of the wall kit will take one to two weeks, and the installation of the whole house - no more than three months. Products fit tightly to each other, which increases the thermal insulation properties of the walls. In terms of heat preservation, a beam of 150x100 mm is not inferior to brickwork and a log cabin.

A house made of timber gives a slight shrinkage, which is 2-5%. The material is easy to finish, and communications can be hidden in the walls. This cottage looks elegant, neat and harmonious.

House from a bar 150x100 turnkey

The company "MariSrub" offers the construction of turnkey wooden houses, including from a bar with a section of 150x100. We carry out a full range of work, which includes:

• Project creation;
• Production of lumber for the project;
• Foundation installation;
• Assembly and installation of a log house;
• Roof erection;
• Carrying out and connection of communication;
• Final finishing.

In "MariSrub" you can order an individual project or a ready-made version, in which the architect of the company will make the necessary changes. The company's catalog includes small country houses up to 100 square meters and spacious cottages for permanent residence with an area of ​​150-200 square meters or more.

We build one- and two-story houses, buildings with an attic, balconies and a terrace. You are sure to find a project to your liking! And if you do not like any of the options, choose an individual design. When ordering turnkey construction, we develop a project for free!

If you plan to build a house from a 150x100 timber for permanent residence, the experienced employees of MariSrub will carry out high-quality work on the insulation of walls and floors, select reliable insulation and other finishing materials.

Masters of "MariSrub" produce lumber on their own. They carefully select and process wood, comply with the norms and requirements of GOST. We offer only high-quality and reliable products from a durable and sustainable winter forest!

The bar passes safe drying and processing by protective means. Such procedures increase the service life of products and reduce the number of defects. The wood does not crack or rot. It is reliably protected from deformation, the negative effects of insects and moisture. Such a house will easily serve for several decades!

We have already talked about the square section of the beam. But a person who does not know about construction raises many questions about a rectangular section with different edge widths. For example, timber 150x100, where is it used, and what features does this material have? We will talk about all this below.

Use the material of this section for the construction of baths, garages, cottages, various buildings. This is already a full-fledged building material. Such a section is traditionally used in order to save money during the construction of its bed on a side of 100 mm. Since its price does not differ much from 100x100, the dachas come out of it cheaper. If you build a large residential building, then you need to put it on the side of 150 mm, which means that the cross section will already be 150x100. And here, too, there is a benefit, since it is cheaper than a material with a section of 150x150.

It is made from various types of wood, but traditionally it is a coniferous timber. Since it is taken in order to save money. But there is material from hardwood. For example - ide, linden, oak. This type is used in the construction of baths and for furniture production. In cottages, it is used as a floorboard, but it will be a chic option. It is also used as a log and rafters.

Features of timber 100x150

1. If we compare it with other smaller sections, for example 50x50, 100x50, then this type is more durable and can be used for load-bearing walls of a structure.
2. Since its most frequent use is as rafters, professionals call the section 100x150 a rafter beam.
3. This kind is quite heavy. For example, with a length of 6 m, it will weigh 78 kg. So it will be difficult for one person to cope with it.
4. For outbuildings, a garage, a bath, this material is placed on the edge, and the cross section will be 150x100.
5. The section 100x150, due to the peculiarity of its shape, was loved by manufacturers of windows and doors.

How to purchase and calculate a beam with a section of 100x150

It is better to buy such lumber in cubes, since it is already wholesale from the manufacturer. And it is not difficult to calculate how much timber is needed. Below we present a table with different types of timber section and quantity in a cube.

But first you need to know exactly the design of the house or bath. For the construction of such buildings, a length of 6 m is usually used. And the length of the walls and partitions, if they are made from the same section, will give the number of sticks for one crown. And then we already calculate, given the height of the walls.

Here you should immediately think about which side you will have a technical side, that is, the section will be 100x150 or 150x100. But from the resulting size you need to subtract the size of the door and window openings.

The number of timber in a cube

cross section	1 piece from a cube	pieces per cube
100x150x6	0.09	11.11
150x150x6	0.135	7.41
100x200x6	0.12	8.33
100x150x7	0.105	9.52
150x150x7	0.1575	6.35
150x200x7	0.21	4.76

How to build a house or a bath from a section of 100x150

A log house of the 100x150 type is already assembled on site, a rough assembly is not done at the factory if it is a turnkey house. The largest number of questions was caused by the connection to the corner of this section. There are two ways: Corner connection or Remainder connection. You need to fasten the bars with dowels, and it is better from a tree with a diameter of 3 cm.

The first row is laid on the foundation, connecting the corners to the floor of the beam. The second row is also made into a tree floor or by connecting the timber with the help of special dowels, or by the method “in dressing with a root spike”. This method has one big disadvantage. This is a lot of airflow in the corners. So you need to immediately take care of their warming. A special jute is laid between the timber. But there is a peculiarity here. If the beam is profiled, then you need to make sure that it fits snugly into the groove. And you can strengthen the walls and make the fastening of the beam with each other more reliable with the help of steel anchors.

If you are building a residential building or a dacha that you are going to visit in the winter, then this section is not enough for the “Russian winter”. It is better to insulate the walls and make a ventilated finish, such as a block house or siding. The entire timber is carefully processed before starting work. And at the end, plums and all waterproofing are necessarily made, do not forget about the “friendship” of wood and water.

Price and manufacturers of timber 100x150 mm

The factors that form the price for this type are no different from any other lumber, these are: humidity, raw materials, type of processing. But this product already has a type of geometry added: profiled and regular. But to build a house, it is better to take a profiled version, it will cost from 10,000 rubles per cubic meter. For lags and rafters, you can use the usual cheapest option for 8,000 rubles per cubic meter. Approximate prices for this type of section are presented in the form of a table:

Wood	Type of processing	Humidity	Price per cube, rubles
Pine, spruce	array	natural humidity	4600-6000
		Dry	5600-7000
	Planed	natural humidity	7000-8500
		Dry	8500-9000
	Glued	Dry	14000-16000
Fir, linden	array	natural humidity	13500-15000
		Dry	14500-16700
	Planed	natural humidity	17000-18000
		Dry	18000-20000
	Glued	Dry	25000-34000

Not all entrepreneurs make such a cut. We have selected the largest and present them to you.

When choosing this lumber, you need to be extremely careful. This section is the most popular on the market, which means you can find a lot of timber from artisanal manufacturers who are not at all responsible for the quality of their products. If you are offered too low a price, then think about it!

IC "BrusHaus" brings to your attention. Our catalog of projects contains a large number of different cottages, of various sizes, areas from 100 sq.m. up to 150 sq.m. All placed buildings can be used both for permanent residence and for seasonal. On average, all projects are designed to accommodate up to 3-4 people. Individual houses made of wood have been very popular among the population of our country for a long time. The main reasons for the high popularity are the excellent soundproofing properties of wood, thermal properties. And also the fact that wood can "breathe". In addition, quality buildings are famous for their durability, as a building made from quality material will in fact have increased strength!

What are houses made of timber from 100 to 150 sq m?

Houses from a bar 100 150 sq. m can be erected as one, two or one and a half floors. As a rule, the second floor is made attic, but there are exceptions. The roof is often made gable or broken. The following rooms are usually organized in the house:

1. Kitchen (dining room)
2. Living room
3. Bedroom - as a rule, they make at least two bedrooms, but there are projects where their number reaches as many as six!
4. Sanitary units
5. boiler room
6. etc.

Call, order in SK Brushouse . We have been in the construction services market for 15 years. Our teams of professionals are ready to implement projects of any complexity in a reasonable time frame!