Swing from old tires with your own hands. How to make a swing from old tires with your own hands: instructions with a photo. Making a horizontal swing from a tire

If you firmly believe that the list of tire swings is limited to uncomfortable vertically or horizontally suspended tires, then you are VERY wrong. Variations of models of ground and suspended swings are so numerous that they amaze the imagination. Usually it is a one-piece wheel, with parts cut in strategic places, bent and / or riveted together. And also additional decorations, of course. Creative thought makes all kinds of animals out of car tires, miniature vehicles (from airplanes to motorcycles) and even swing chairs. And you can recreate almost all of them with your own hands without special skills and talents. We look:

A swing for toddlers from 5 years old, when only a thin inner rim is left from the tire (on the right, a wide one, cut with a fringe for beauty) and a piece of rubber at the bottom as a seat. The simplest advanced model. Of course, before creating a swing for children, tires must be thoroughly cleaned and processed. If the harmlessness of rubber still bothers you after that, you can always additionally wrap or paste over such a swing with a cloth, soft self-adhesive film and so on.

Almost the same option, but safer - with a back. And the back can be different:

For the smallest, the most convenient and reliable variation is with a kick and a crossbar in front:

If the wheel is larger, you can make a swing with a backrest for older children. And this is how this craft will look if you guess to paint it brightly and beautifully:

And here is a whole cradle plus an additional design for beauty:

This line is completed by a luxurious swing-chair for an adult, although not a dense person. They are made of a wheel for a truck or tractor.

Also still a simple swing, but with a little "twist": the wheel is cut at the back and cut off at the top, and also bent back ...

… And the cut off side part of the wheel is bent, and the same sidewall from the second wheel is riveted over and across it.

Until we move on to the most creative, beautiful and complex models, consider a few ground swing. A classic for two with a middle lever-based crossbar. As practice shows, if an adult does not decide to swing on them, no additional reinforcement of the half of the wheel from the bottom is required - it will withstand the weight anyway. Usually, such swings are equipped with handles closer to the center, and can be supplemented with soft seats for greater comfort.

These are rocking benches, on which you are supposed to sit, as usual, and swing sideways from side to side.

And these are improved models, when an analogue of a rocking horse is already made from a half of a car tire:

Finally, a wheel on a huge spring, but this is already an attraction for brave young extreme boys, since injuries are possible. Knee pads, elbow pads and a helmet are recommended when in use.

Suspended swing bench made of tires - for the whole family: a classic of the genre, when wooden boards are mounted between the tires, and the latter serve as armrests.

Well, now what we have all been waiting for: a real masterpiece swing made of tires. The production of such swings in the form of animals and various objects has recently become a real business abroad, and people spend a lot of money for such toys for their children.

The main sources, among others, are the same as in previous articles on landscaping and pots, ponds and sandboxes from tires.

Swing from a wheel is the most popular and affordable children's entertainment for making. Old tires are free stuff. The simplest and complex structures, the whole game complexes in the country, are created from car tires.

Pros and cons of wheel tire swing

If you analyze it carefully, then children's entertainment from wheels has many advantages:

Rubber wheels are durable material. Such a swing is almost impossible to break, deform.
Different wheel sizes make a swing for all ages. You can make entertainment for adults, teenagers, children and even a cradle for a small child.
If you show your imagination, find it on the Internet or come up with an unusual pattern, then the cut tire will make an original swing seat.
Wheels are not afraid of heat, frost, rain and other natural phenomena. The swing will stay in the open air all year round, and this will not reduce their service life.
A big plus is the fact that swings from old tires are made free of charge with your own hands. The wheels are being sought out in the junkyard. It will remain to attach the material available at home to them: chains, rope, log or board.
Primitive swings are considered less hazardous in terms of injury. If the child accidentally collides with the rocking seat, the rubber will soften the impact. In extreme cases, you can get off with a slight bruise.
The swing is so easy to make that even a person whose arms are growing out of the wrong place can make them.

Among the minuses, two points can be noted. First, rubber gives off an unpleasant toxic odor in heat. Secondly, the large wheels have an impressive weight. Reinforced support will be required so that the swing does not break.

What you need to make a swing from car tires

To get a safe and reliable gaming complex, you need to choose the right material for its manufacture. In particular, there are many requirements for wheels. After all, it was they who became the main material. However, the tires themselves will not make a swing.

Auxiliary elements will be required. A selection of tips will help you choose the right material:

If possible, it is better to choose wheels from imported cars. Domestic tires are hard, they will create discomfort for the child. In addition, these tires are more difficult to cut or bend the chair out of them.
Winter tires are considered to be the most elastic. It is easier to make a swing from such wheels in the form of a cradle, chair and other unusual shape.
It is optimal to use wheels from cars for hanging swings. They are lighter. Tires from agricultural machinery are distinguished by their large size, impressive mass, and increased rigidity. It is better to bury them in the ground for the base of the swing-balancer.
Usually, a swing is made from old tires, but they should not be badly worn out. If the wire of the court peeks out of the rubber, then such material is dangerous. It needs to be thrown away.
Old wheels are heavily soiled. Before use, tires are washed well with water and detergent.
The shape of the tire is designed so that when it rains, water will accumulate inside. The suspended wheel must be drilled from below. 2-3 holes with a diameter of 8 mm are enough.
A tree serves as a free support for the suspended swing. Here, too, you need to make the right choice. An adult tall tree with a thick and strong crown will do. The wheel must not be suspended on dry and thin branches. They can break off.
Advice! The optimal location of the tree branch for hanging the swing is 2.5 to 3 m above ground level. The presence of other branches down the trunk is unacceptable. You can catch on them while riding, get injured.
A branch of a tree with a thickness of 25 cm is considered strong. It is great if it has side branches or knots. They will act as limiters to prevent the rope from sliding down.
It is best to use climbing ropes to hang the wheel. Metal chains are more durable, but when swinging, they peel the bark of a tree.

When the material is prepared, it is time to create a swing from car tires with your own hands according to the scheme you like.

How to make a swing from a tire with your own hands

There are many options for creating children's fun with tires. Structures differ by support, by the way the tire is suspended or installed on the ground, and other nuances.

Swing-nest from a tire

A tire swing seat horizontally suspended from chains or ropes resembles a nest. This is where the name came from.

A thick branch of a tree or a self-installed crossbar acts as a support. It can be made from pipes or hewn logs. Two racks are buried on the sides. You can create two identical structures in the shape of the letter "L" or "A" with a jumper for rigidity and simply install them on the ground. From above, the supports are connected with a crossbar.

To suspend the wheel, eye bolts are screwed into its side part. They can be installed in four pieces, evenly spaced from each other. Each pair is connected with a chain thrown over the crossbar. The socket will only swing back and forth. In another embodiment, three eyebolts are installed at an equal distance. A piece of chain about 1 m long is taken from each eyelet. At the top they are brought together, connected to one chain and fixed to the crossbar. Such a nest will be able to swing and rotate around its axis.

Advice! For a rotating nest with three eyebolts, it is better to use a rope instead of chains.

Tire balance swing

The classic design for pair skating is the balance bar. The essence of the device is in the presence of a support located in the center of the board. Two children sit on the ends of the arm. Under the influence of their own weight and repulsion from the ground, their legs begin to swing.

Creating a swing from a tire with your own hands can be considered step by step in three options. For the first design, the support is made from a wheel. The tire is sawn into two halves. It only takes one piece. Cut pieces of boards are inserted along the edges of the cut. These will be embedded elements. Their length corresponds to the width of the tread. Boards are attached to the bus with self-tapping screws. For the next part of the swing, a board about 2 m long is needed. The workpiece is polished, a handle is attached at both edges. The board is bolted to the embedded elements on the bus. The support from the wheel must be located strictly in the center, otherwise there will be an overweight on one side.

The balancer is not tied to the ground by the support. The swing can be moved anywhere. For aesthetics, the wheel and the board are painted with bright paint. You can draw patterns.

The next version of the balancer is tied to the ground. The support is made of two vertically dug logs or pipes. They protrude from the ground to a height of about 1 m. The parameter is selected according to the height of the children. The supports are installed parallel to each other at a distance of 50 cm. At the top point, coaxial holes are drilled, a jumper made of a thick metal hairpin is inserted.

A hewn log with a length of 2 m is drilled in the center. String it on a hairpin between the supports. Two nuts are screwed on from both ends. At the edges of the logs, seats are attached from a piece of board, and handles are installed. In places where each seat will touch the ground when the lever is lowered, the wheel is buried vertically. During the swing, the swing will not hit the ground, but will spring from the tire.

The third version of the balancer is designed as a rocking chair for one child. As in the first design, the wheel is cut in half. On the ends, they put mortgages from pieces of the board. The seat is made to fit the length of the half-ring of the cut wheel. The board is bolted to the embedded elements. The rocking chair is painted with bright colors. On request, handles can be attached to one side.

In the video, an example of a swing from a wheel:

Vertical tire swing

According to the nest method, a swing is made from a tire on vertical chains. A tree branch or a self-made crossbar acts as a support in a similar way. Only the way the wheel is fixed is different. Eye bolts are not screwed into the side shelf, but into the center of the tread. Here, similarly, there are two options. You can screw in one eyebolt and hang the wheel vertically on one chain. You will get a bungee with which you can jump on the sand.

If you screw two eyebolts into the tread at a distance of 40-50 cm, the wheel is suspended with two chains. You get the classic version of the swing. In both cases, the tire must be perforated from below. When positioned vertically, water will accumulate inside the wheel when it rains. It will drain through the holes.

Advice! The vertical swing can be suspended from chains and ropes.

Swing cradle from a car tire

If there is a small child, do-it-yourself garden swing from tires is made out with a cradle or an armchair.

For the first option, you will need a large diameter wheel from a truck. With a knife, the protector and the side shelf are cut to half. The rim rings themselves are left. The protector can be cut completely or folded under the bottom of the cradle, where the ends are bolted together. The structure is tied with a rope for two rims, suspended on a support.

For an older child, an original chair is made instead of a cradle. There are two ways to cut the tire. In the first option, you need two wheels from a car. The side shelves are completely cut off with a knife. One tread ring is used to form a seat body with side walls. The part is placed horizontally. From the second ring, the back and the seat itself are made. The part is bolted perpendicularly to the horizontal body.

The second option requires one wheel. Cut off one side shelf with a knife. On the other hand, the rim is cut from the tread to half. Now it remains to unscrew the tire, create the shape of the chair, and fix it with bolts. The finished swing is attached to the support with eye bolts and chains. For an illustrative example, in the photo, the do-it-yourself swing from the wheel is shown above in two versions.

A few useful tips will help you better equip a playground for children, ensure safety, and find new ideas:

For the winter, it is advisable to remove the swing in the barn. The frost is not terrible for the tires, and the ropes can sweep. The chains will rust. In the spring, children's entertainment will not be put in place for long.

Conclusion

A wheel swing can be created in one hour. Even the simplest design will provide a child with entertainment for the whole summer.

They are easy to manufacture, enjoyable and reliable to use.

What needs to be prepared for the construction of a swing with your own hands? What is the manufacturing technology? Let's talk about this in the article.

Required tools and materials

To make a swing you will need:

tires (1-2 pieces, depending on the type of swing);
thick rope, thin rope or chain;
bolts with rings.

The continuation of the list of required materials and tools will depend on what you will mount the swing on: on a wooden or metal base.

If on wooden base, you will need:

three thick wooden beams;
hammer and nails.

If on metal base:

three durable metal pipes;
welding machine.

In addition, you will need a shovel to dig holes for the bases, and rubble to fix them.

For information on how to properly plant a daylily and take care of it, read in.

Instructions for making a swing from tires

Step-by-step technology for making a swing from tires

First you need to make a seat. As it, you can use a whole unmodified tire, but you can, by performing simple manipulations, connect two tires, and get an almost full-fledged seat.

If you decide to use only one tire, leaving it in its original form, you need to make several holes in it. Usually, 3 or 4 holes are made (in the form of a triangle or square) on one of the sides of the tire.

The simplest swing is made from one tire.

In the holes you need to fix a rope or chain, depending on your wishes, by means of bolts with rings. We screw in the bolts so that the rings are at the top, and we pass the rope through them. It is assumed that the tire will hang horizontally.

Complete swing seat

You can cut a seat from one tire. To do this, we cut off one side of the tire completely, and cut the other side only in half.

We bend inward the part where the side is not cut off, thereby the free part will lie on its side and will serve as a back. The ring should be secured with bolts.

We make holes in four places: two from one side and two from the other, and screw in the bolts with rings.

We make a comfortable swing from two tires

If you want to make a comfortable swing, you need to arm yourself with a knife and prepare two tires.

Cut off the upper and lower parts of the tire so that only the ring remains. The same is done with the second bus.

We fold one of the tires in half and place it on the other vertically across, so that the back of the folded tire lies on the inside, and the bottom on the outer first tire-base. Everything needs to be fixed with bolts, giving the correct shape to the future swing.

At the end, you need to prepare the rings through which we will thread the rope. The swing is ready, it remains to hang it.

The height of the swing depends on who will swing on it. For the child, hang them at waist level so that it is comfortable for him to sit down.

Features of mounting a swing on a tree:

Find a large tree, choose a thick, sturdy branch at least 15 cm in diameter, located at a height of two to three meters from the ground.
Throw one end of the rope (chain) over the bough and fasten it in rings on the swing, with the other side doing the same.

Features of fastening a swing on a wooden base:

Two thick beams must be installed in pre-dug pits about 40 cm deep, for strength, fill the free space between the beams and the walls of the holes with gravel, tamp and fill with earth.
We insert a bar between them, which will serve as a horizontal support for the swing, it must be firmly fixed with bolts. In the crossbar, you need to fix metal brackets or screw in bolts with rings.
We fasten the ropes in the rings and the swing is ready.

You can read about how to grow clematis in the garden.

Want to create a romantic atmosphere with

There are many toys in the country of childhood. The girls have some, the boys are completely different. But as soon as a structure appears in the yard, on which you can ride, it attracts children of all ages, both boys and girls. Even if this swinging structure is nondescript, children will still be delighted with it. Even a simple tire swing that someone's caring dad builds with his own hands will make such an impression on them.

The device of the simplest children's swing from a tire

It will bring joy not only to the beloved child, the children of the yard, but also to young people who are not averse to swinging on this simple device. Swinging structures, besides being fun for children and adults, also strengthen and develop the vestibular apparatus. Such are the usual tire swings. Every parent can build them.

If a child, when he travels in a car, gets nauseous or nauseous, then he should swing on this structure at least once a day. When rocking, all muscles of the body are evenly loaded, and this makes the baby physically stronger and more confident in himself. He will stop weakness and dizziness, and the fear of quick movement and height will disappear.

Such devices have pros and cons. Positive sides:

The disadvantage is the smell emanating from the rubber, which not everyone likes. You can get rid of it, or at least reduce it, if you cover the tire with paint from the inside and outside. At the same time, it will acquire a more attractive appearance.

Requirements for tire swing

First of all, they must be very reliable, since they are installed for the most privileged members of society - children. Therefore, a strong tire is needed, without cracks, damage. Preferred tires for SUVs, tractors, trucks. But it is better if it is medium in size so that it is comfortable to swing for both children and adults.

Hang the tire on a strong rope or metal chain. To keep the seat securely in a horizontal position, not to roll over, it can be done with a triple fixation. From above, the device is attached to a horizontal crossbar, which can be a strong beam, a metal crossbar, or a thick branch of a strong tree.

The distance from the ground to the seat should be such that the child can climb onto it without difficulty. The classic version is double chain fastening of the bar. It is the most durable, very comfortable, safe, because, swinging, you can hold on with both hands. Install ground-based or it is necessary so that playing children are always in sight of their parents. When erecting ground structures using a half of the bus as a support, it is always necessary to ensure their high stability.

A variant of the device for a children's swing in the form of animals

So that the rocker-balancer does not fall on its side, it is better to use both parts of the cut tire for the base, fastening them along the entire semicircle to each other. Handles should be made on the lever board, which children will hold on to while rocking.

Views

It would seem that with such limited material, one cannot count on variety. But craftsmen work wonders with their own hands. Therefore, tire products are as follows:

Ground rocker-balancers in different variations;
Hanging swing with vertical and horizontal tires;
Figured swing-cradles with armchairs made of tires, as well as seats in the form of various animals and birds.

Ground rocker-balancer

This is a classic swing. None of them can do without such a simple design. Two sit on the edges of the lever board and swing, then rising, then falling.

Instructions for making a ground rocker-balancer from a tire

To lift one shoulder of the swing, the child sitting on it pushes off the ground, and his partner lands on his feet.

Such devices are of the following types:

Swing on two car wheels;
Balance weights on tire halves;
Rocking chair from the tire for the children's room.

To make such a balancing device with your own hands, you need a solid smooth board made of wood or some other material and a solid support for it. The original basis for the swing can be two automobile wheels with tires, connected axially by a metal crossbar, to which a lever is attached in the center.

Children and adults like to swing on such a structure. It is also convenient because it can be easily moved around your own yard or summer cottage. There is another version of the rocker-balancer.

Take a wide tire from the wheel of a large machine, for example, a tractor or tractor, cut it across and use one half as a support. You will also need two planks. One should be equal in size to the diameter of the tire and fit tightly into its upper part, where it is attached to the rubber with nails or self-tapping screws. The second, long, is superimposed on the first and fastened to it.

For the convenience and safety of swinging, handles should be attached to the board, preferably from a soft material. In the lower part of the tire, holes must be drilled so that water does not accumulate in its cavity.

More stable will be those devices in which two halves of the tire are installed as a support.

They will need to be bolted together along the entire semicircle, and a long board should be fitted on top. For greater attractiveness, rubber should be painted in bright colors, applied with drawings.

An example of painting a children's swing from a tire

You can make a small swinging balancer with your own hands for, moreover, without having special skills. The technology of its manufacture is the same, only the top plate in length should be no more than the diameter of the tire. You can swing while sitting on it only sideways, left and right. Armrests must be made around the edges so that the child can hold on to them.

And if you saddle the balancer from above, you will get a new fun: it will be possible to swing back and forth. On the one hand, instead of a handle, you can fix a horse's head carved out of wood, and on the other, a tail. Such rocking chairs are very popular with young children. You can come up with a stylized figure of another animal. It depends on the ability and creative imagination of the Pope.

Suspended tire swing

They are also very easy to build with your own hands. The main thing is to find a suitable crossbar to hang them. This can be a horizontally growing thick branch of a tree, a beam in a barn, or a specially mounted metal structure. And as a seat, of course, a car tire is suitable.

You need to choose rubber without damage, and strengthen it with a more attractive side up.

Before attaching ropes or chains, wash the bar thoroughly with detergent. The simplest swing is a tire hanging vertically on one rope or chain. Making them with your own hands is as easy as shelling pears. They ride on such a swing, passing their legs through the wheel and hanging them on the other side.

The original design of the suspended swing from the tire

Swing, holding a single mount with both hands. But this is not entirely convenient. Such a device is usually suspended from a tree by the river itself, and the boys, standing on the tire, or grabbing its lower edge, swing as much as possible, and then jump into the water. True, not every child will decide on such entertainment.

In the yard or in the country, it is better to make a swing, in which the horizontal seat is held on a double mount. It is desirable that it be a metal chain. Attach it to the tire using cargo bolts, which have a ring instead of a head. For them, holes are drilled in the rubber, fixed, and S-shaped hooks are inserted into the lugs. They are threaded into the lower chain links and clamped with pliers.

Attaching hooks to the tire

The upper ends of the suspensions are fixed on the crossbar. For convenience, a round wooden plank is placed on the tire, and a pillow or rug is placed on top of it.

There is another option for a suspended swing - a cradle made of tires. It is also made by hand. With a boot knife or other cutting tool, cut the tread in a circle to the power ring of the steel cord, leaving only a part of the rubber for the seat. From above, ropes or a chain are attached to the resulting circles and suspended from the crossbar. Even very small children can be rocked on such a device.

Curly swing

You can cut anything from the rubber from the tire. By bending it, you can make a chair with a back. Craftsmen make swings in the shape of various animals and birds. Sometimes, near a private house, there is a figurine of a horse, on which the baby sways, sitting astride. Some make rubber birds, dragons, even cars and motorcycles. Children enthusiastically climb onto such rocking chairs. The dads' fantasy is endless and they willingly share it on the World Wide Web.

This master class describes the process of creating a swing from tires. If you have a summer cottage, then perhaps you should pay attention to it. We've prepared an easy-to-understand step-by-step tutorial and tips for you, as well as some great examples for inspiration. You will learn how to make a garden swing from tires with your own hands and will be able to transform your summer cottage at no special cost.

Children like this kind of swing. Of course, many adults will love them too. Working with tires is quite easy, and most importantly, it is very easy to paint them and make them bright, beautiful and original. Several pairs of tires can be used to make an entire playground in just half a day!

What do we need?

cleaning agent
U-bolts with nuts and washers - 3 pcs
strong chain
U-shaped attachments for the chain - 4 pcs
spray paint

It is worth mentioning separately about the choice of a tire for a swing. Tires from foreign manufacturers are best suited, since Russian tires are more rigid, and therefore it turns out to be quite problematic to drill and cut them. This is especially true in those cases when you want to make some kind of unusual garden swing from tires. It is also important to add that it is most convenient to work with winter tires - they are also easier to cut.

It is important to pay attention to the fasteners. In this case, we are talking about a chain, but it can be replaced with a strong rope rope.

Also remember to wash the tire with a tire cleaner. If you don't have one, then calmly replace it with dishwashing detergent.

How to make a swing?

The first thing we need to do is drill six holes for the three brackets. The staples must be placed at an equal distance from each other.

At this stage, we paint our tire. It is preferable to use aerosol paint - it is convenient to work with it, it does not stain clothes after drying and fits well on the material.

We place the bolts in the holes and fix them with washers on the inside of the tire.

We pull three chains up and on the other side we connect them with another fastener. In the same place, if necessary, we fix a hanging carabiner or a ring - it depends on where you put the homemade swing from the tire.

Ready! It remains only to securely fix the structure on a solid beam.

This is the easiest way to create a swing from tires with your own hands. You can of course do something more original. Take a look at these examples for inspiration and try repeating the workshop or doing your own.

Swing boats

The tire must be cut in half and the side cut off. The holes are made in the same way as in the master class above. You can insert staples with a chain or just a rope into them.

It is better to paint the tires for such a swing from all sides - it will be more beautiful this way.

Vertical swing

The manufacturing principle will be exactly the same. It's just that in this case, the tire is mounted vertically.

In this case, it is preferable to use a chain, not a rope, since there will be only one fastening, and not three, as in the horizontal version.

Inverted tire

If you are making a swing for a small child, it makes sense to make something like a hammock. To do this, the tire must be cut and turned out. The excess part is cut off.

Hanging such a swing is easy - just rewind the tire with a rope. You can also use staples and a chain. If desired, an interesting pattern can be made on the tire.

Swing chair

You will need two tires to create the chair. The first part is cut and turned inside out. The second part is attached to the first with screws and is a piece of the flattened part of the tire.

It is best to attach such a swing on a chain. If you wish, you can put soft pillows or a blanket on it.

Swing painting

Make your swing colorful to make it even more fun for kids to use. If you are making a swing from a tire with your own hands for the first time and are not too confident in your artistic abilities, draw a ladybug - this is the easiest way. This option looks very funny and beautiful.