DIY wood crafts for the garage. DIY Garage Tools - Turn your caravan into a home workshop! Properly organize the lighting system

Absolutely everyone can make accessories for the garage with their own hands. With the help of such products, the owner of the premises will free up a lot of space, and tools and equipment will always be at hand.

A workbench is a necessary item in every garage

A homemade workbench should be in every garage. It does not take up much space and makes it possible to comfortably make repairs and make useful crafts. Usually a workbench is made of durable wooden planks that are attached to a thick wooden beam or profiled pipe. Often the workplace is made of steel billets. They are quite easy to cut and fasten into one solid structure using metal corners and universal screws.

To make a workbench, as well as other machines for the garage, you need to draw an accurate design plan. When doing this, consider the space that will be allotted for the product. It is best to put the structure next to shelves or racks. In the drawing, note the presence of drawers and shelves. In them you will store small fasteners and tools. A compact vise can also be attached to the tabletop. Having drawn a plan, proceed to the manufacture of a workbench. First, we collect the countertop.

If you have a small room, then it makes no sense to make an overall homemade product for it. You can connect the boards to each other with good glue and metal ties. As a rule, the countertop of a standard workbench consists of 5-10 identical boards. Next, we make special grooves on the tabletop with dimensions of 2.5x2.5 cm. They are needed for stops. As soon as the glue on the product dries, the surface must be planed. The result should be a perfectly even coating. The legs for the structure can be made from several bars measuring 80x10x10 cm.

In the front legs we make grooves into which the brackets will be inserted. In the future, the latter will be connected to the longitudinal beam of the table top. Then we assemble the base of the underframe. It consists of two frames, which are made of boards 5x10 cm. The base is attached to the support, after which the frames cut into the legs of the workbench by 2.5 cm. At the end, we fix the components with bolts. Then you need to attach the back and side support walls to the workbench. For their manufacture, sheets of chipboard or centimeter plywood are taken.

The last step will be the connection of the countertop and the top frame. To do this, use powerful bolts. After that, we apply drying oil to the coating of the workbench. As soon as it dries, the surface is treated with varnish. As a result of the work, you have received a stable structure, on which you can not only repair spare parts or make various crafts, but also store the tool.

We make a rack - about a complex structure in simple words

Every driver probably has a lot of large garage fixtures that have nowhere to store. Where can they find such a place so that later you can quickly find the right tool? The correct answer is on the shelf. This design will allow you to organize free space and save a lot of time. Similar devices for the garage can be made of wood or metal. The second option is more reliable, but it is quite difficult to implement on your own.

The first one is much easier to perform, however, in order for the structure to last for a long time, it is worth choosing strong wood species for work. Beech or oak are perfect for this. Drawers and shelves from them can withstand significant loads. In principle, the ability to withstand a mass of 150–180 kg is considered the norm for a rack. In practice, only a few adhere to these recommendations. However, be sure to remember that the maximum weight of all tools on the rack should not exceed 300 kg. Otherwise, this design will become dangerous for the garage owner himself.

It is very difficult to make a rack that is complex in design. It requires considerable effort, a lot of time and equipment. It is not much inferior to a simplified product, the manufacturing algorithm of which we will consider in more detail. So, the order of work is as follows:

1. 1. First you need to take a board 9 cm wide and cut it into pieces of different sizes. In the future, these details will play the role of supports for the structure.
2. 2. For shelves, you will need to take a thicker board. It must be cut into several identical parts.
3. 3. Next, take the board for the base of the rack and mark on it the points where we will make spacers. They should be located at a distance of 3 cm from the edges of the base.
4. 4. Attach the top brace using superglue. We nail the top shelf to it with nails. The same manipulations must be repeated with other spacers and shelves. The bottom bursting part should be attached last.
5. 5. Then it is necessary to turn over the assembled product, pull off the base of the rack with spacers, using screws for this.

After the work done, your rack is almost ready. In the end, you just have to clean the surface of the rack with sandpaper and treat it with oil varnish. It is best to apply the latter in 2 layers. Fasten the structure to the wall with powerful anchor bolts by screwing the fasteners under the top and bottom shelf of the structure.

Cyclone vacuum cleaner and press - useful homemade products for a tinkerer

The list of home-made machines and devices must necessarily include a press. This clamping device will become an indispensable tool for every lover of home art. To manufacture the press, you will need a hydraulic jack, a metal platform frame and 4 profile pipes. Two of them should have a section of 4x4 cm, and the rest - 6x6 cm. To make a press, we take two pipes with a smaller section and attach them to the base of the product. At the very top, between these pipes, we weld another pipe with a large cross section.

Install the remaining pipe in such a way that it can easily move along the previously mounted guides. The device made in this way works according to a very simple principle. To connect two products, they must be placed on the base of the press and covered with a dense plywood sheet. The pipe with the jack installed must be lowered, and then two short pipes must be turned. By making this simple movement, you will securely connect the two previously delivered products.

The second device is a cyclone vacuum cleaner, it will help you always keep your garage in perfect cleanliness. To make it, prepare a plastic or metal container. An important nuance is that the lid of the vessel must be hermetically sealed. Next, we make 2 small holes in the lid. The first should be located in the center, and the second - not far from the edge. The hole diameters and sections of the hoses you use must be the same. We connect the pipes to the holes. The first will serve to collect garbage, and with the help of the second you will connect a regular vacuum cleaner

Install a plastic elbow into the inlet pipe. With it, air will be sucked in by a device, like a cyclone. Thanks to the presence of this knee, the vacuum cleaner will be able to draw in not only dust, but also small stones, sawdust, lumps of dirt and other small debris. All this will remain in the container to which you connected the hoses. If you wish, you can not equip the vacuum cleaner with a knee. But in this case, you will not be able to clean up the garbage, but only the dust. In such a device, it is best to use a plastic container and narrow hoses. If you need a more powerful device, then you should make a vacuum cleaner from large hoses, an elbow and a steel container.

Rope making device - ropes from plastic bottles

During the heating process, plastic bottles shrink quickly. Thanks to this, we get the opportunity to make quite strong ropes from them. With their help, the garage owner will be able to connect several different products that are used on the farm. To create a device, you need to find two bolts with nuts and washers, a piece of thin board, an electric drill and a clerical knife. After that, we take two washers and put them in the middle of the board. The centers of the pucks should be marked on the board with a marker. Drill holes at these points.

Next, drill holes on the back of the board. This must be done to prevent rotation during operation of the device. The next step is to tighten the bolts. We test the device. We put a few washers on the protruding ends of the bolts. The final thickness of the rope will depend on the number of bolts. Next, place a clerical knife or a small piece of it on top of the washers. We fix the device with additional washers screwed in until it stops. Next, the device must be fixed on the desktop using clamps.

Then we take a two-liter plastic bottle, cut off its bottom and cut out a strip in the rest. We put the latter on the device so that it is located under the knife. Next, we take the strip with one hand and pull it, and with the other hand, you need to hold the plastic container. As a result, from one unnecessary 2-liter bottle you will get about 20 running meters of rope.

How to make a viewing hole - detailed instructions for beginners

Like it or not, sooner or later the car has to be repaired. And so that the owner of the car does not have to crawl under the car and “squirm”, bending twice, it is necessary to dig a hole in the floor of the garage for inspection and repair. First of all, those who want to do this need to mark out the area of ​​\u200b\u200bthe room where the car is parked. To do this, the garage area is marked with chalk. When drawing up the markup, you need to consider several important factors. The length of the pit should correspond to the length of the car, and another 1 meter must be added to this value. The width should be such that it is convenient for you to work. However, be careful - this value should not be more than the distance between the wheels of the car.

The depth of the pit is calculated taking into account the height of the garage owner. An additional 20 cm is added to this indicator.

"Having taken measurements", proceed to digging a hole. Having done this, think about the arrangement inside. First of all, this applies to the walls of the pit. To this end, bricks, building blocks or concrete can be laid out on the sides. The wall thickness directly depends on the material. So, if you use ceramic bricks, then this figure should be 20 cm. If you purchased cement, then the wall thickness should be 12 cm. If you want to make walls from blocks, then their thickness should not exceed 22 cm.

Do not forget that the walls of the pit will require hydrophobic impregnation. It will protect materials from moisture. It is necessary to apply impregnation from the inside of the brick or blocks. For a more comfortable entry and exit, we make steps in front of the pit. It is best to use cement for this. You need to start from the lowest step, gradually rising higher. Each of the elements of the stairs must be the same. To achieve this, first measure the height of the lift and calculate the number of steps.

Shelves indoors - for storing loose fasteners and more

Sometimes the area of ​​\u200b\u200bthe garage does not allow you to make and install a large spacious rack in it. In this case, you can make shelves of different sizes. They will be attached directly to the walls at any height convenient for you. This will save space on the floor of the room. First of all, you need to determine the place of fixing the shelves. On the selected section of the wall, we make an approximate markup, dividing the area into identical squares. Dowels will be screwed into the corners of these squares to hold the shelves.

To screw in the fasteners, drill holes for them with a puncher. If possible, you should purchase special dowels with hooks at the ends - they will provide better fixation of products. Next, we take a thin board and attach suspensions with eyes to it. When calculating the distance, be guided by the markings you made on the wall surface. To fix metal hangers, use reliable self-tapping screws. After that, it remains to make shelves. We take several boards and cut them into identical parts - they will serve as the bottoms for the products. Then we cut out the walls of the shelves from thicker boards. We nail or glue them to the bottoms. If desired, the products can be painted or varnished on them.

The final step will be the installation of finished shelves in the intended places. When installing each of them, carefully make sure that the products are level and move freely along the guides. If you want, you can glue turned wooden handles to the front walls of the drawers. It will be more convenient to use the shelves with them. A very interesting idea would be the manufacture of shelves from plastic canisters.

If you have a sufficient number of these containers, and in the future you do not plan to use them for their intended purpose, then you can use them according to this principle. First, cut holes in the extreme walls of the canisters. When doing this, make sure that only the right or only the left wall of each of the containers is cut off. Otherwise, the shelves will look inorganic. After cutting out the extreme walls, clean the plastic from burrs. To do this, use a file. After that, it remains to install the shelves in place in the wall or use them as drawers in the rack.

With proper arrangement of space, a garage can serve not only for parking a car, but as a workshop for its maintenance. In addition, a properly planned space will easily accommodate the tools required for this, provide storage of technical fluids and wheels in the off-season. The functionality of the room will allow you to expand the accessories for the garage with your own hands, which you can make from improvised material or purchase in specialized stores with subsequent refinement to suit your needs.

How to organize the interior space of the garage

Given the fact that the number of things in the garage will increase over time, it is worthwhile to rationally use the walls, floor, basement (if any) by equipping them with the maximum number of shelves, hooks, racks. For skilled people, a workplace is determined, equipped in accordance with needs.

Storage of bulky items

All items that occupy the space of the garage are conditionally divided according to several characteristics: large and small, required constantly or used once or twice a year. Depending on this, before starting the arrangement of the space, they work out a list of large things that are not often used, which include:

• winter, summer wheels;
• bicycles;
• skis.

Garage bike rack option

The list may be longer, perhaps the owner of the garage loves locksmithing, then in his arsenal there will definitely be long pipes (plastic and metal) of various sections, bars and boards. For compact, orderly storage of bulky items, garage home-made or purchased fixtures are used, for example:

1. Purchase wall-mounted bicycle holders that allow you to store them in an upright position, which provides significant space savings;
2. For rubber sets, special shelves are equipped, on which each wheel lies separately. They are placed in any convenient place, for example, under the ceiling, along the wall or, capturing the corner space, or suspended from the ceiling or wall on an appropriate support, previously cleaned of dirt, packed in special cases. This method of storing tires is only suitable for kits on disks. Considering cases when tires without disks are stored, a rack is welded from metal, on which the tires stand vertically in one row. Place the device under the ceiling or on the floor, securely fixing it;
3. With the help of homemade mounts, they provide a compact arrangement of skis, ski poles and other sports equipment.

Attention! A place should be provided in advance in the upper third of the wall for storing a removable trunk.

In addition, craftsmen make various suspended ceiling structures that are parallel to the floor to accommodate long objects, such as pipe cuts or beams.

Devices for small things

For many craftsmen, the number of different-sized screws, nuts, bolts, washers is measured by a bunch of boxes and buckets, in which it is extremely difficult to find the right part. To solve the issue, such gadgets for the garage have been invented that allow you to organize small things and ensure that you quickly find the right part, for example:

• special portable boxes with compartments. A convenient option that allows you not only to store, but also to transfer the required parts if necessary. It should be noted that the cost of the boxes is relatively high, so the ideas below will help reduce costs;
• craftsmen sort small nuts and other parts into jars with twist-on lids, while the lids themselves are securely attached to hanging shelves. It remains only to screw the jar into the lid and the details will always be in sight, at hand.

If financial opportunities are available, they acquire compact storage systems for hardware, nuts and other parts, different in size, differing in mounting capabilities.

Tool storage

The working tool is divided into large-sized and small-sized, respectively, home-made devices for the garage will be different. In most cases, the owners prefer to store a cutting machine, puncher, and other large tools using “native” drawers. Therefore, for their convenient location along the wall, a rack is made from improvised materials, taking into account the total load on the shelves (for home-made structures, the weight should not exceed 150 kg).

Attention! The stores offer a wide variety of models of shelving, made of both wood and metal, withstanding loads of up to 500 kg or more. At a relatively low cost, it is convenient to purchase a ready-made shelving in the garage for the desired size, fixing it against the wall.

For small tools such as wrenches, screwdrivers, pliers and others, organize the space depending on their number:

• sets are stored in purchased boxes, placed on a rack;
• for single items, they either equip cabinets in which each tool is fixed in the corresponding niche, or prepare a perforated surface (as in a store) mounted on the wall and determine a specific place for each of the tools.

Some craftsmen place their tools using plastic pipe structures, in which holes of the appropriate diameter are made.

Homemade machines for garage work

For comfortable repair work, a place is provided for a workbench (to save space, it can be made folding). To begin with, they work out a table drawing, thinking over the presence of retractable shelves, then they make it from boards or metal sheets, equip it with a vice and a grinding machine.

In some cases, craftsmen cannot do without home-made machines and other devices made independently and improving the quality of the manufactured item.

Press from improvised tools

Homemade garage press

One of the most popular do-it-yourself gadgets in the garage is the press. To create it, you will need a hydraulic jack, a metal surface that will serve as the basis for the moving part of the press, springs and profile pipes or a channel to create a frame. Further:

• create a frame by welding channels and reinforcing the structure with transverse stiffeners, transverse corners are also welded downwards for stability;
• the movable platform is attached to the upper frame with springs, a jack is installed.

The efforts of the press are regulated by a jack.

Homemade screwdriver holder

Depending on the needs of the garage owner, other useful home-made machines are made, for example, drilling, made on the basis of a drill, fixed with clamps and moving along the rail with the help of a gear or cutting, or turning.

In addition to the above devices, you should take care of the location of work clothes, provide for the presence of a fire extinguisher or sand (based on fire safety rules), consider ventilation and lighting systems.

Thus, having shown a little ingenuity and thriftiness, you can make do-it-yourself garage fixtures, thereby ensuring compact storage of things and freeing up enough space for minor car repairs and work related to servicing one or another home appliance.

vseogarage.ru

DIY garage accessories

For a true car enthusiast, a garage is a second home. And then the first. Therefore, everyone tries to take its arrangement and equipment seriously. The functionality of each square centimeter of area is also very important. This will allow you to work in a spacious room, and tools and spare parts will be stacked and arranged correctly and in perfect order. As for the arrangement in the domestic plan, we will not talk today, but today we will try to save on equipment.

What should be in the garage

In principle, there is no such device that could not be bought. True, not everyone has the opportunity to spend tidy sums on the purchase of Bosch equipment, by the way, it is useful to look through catalogs with Bosch equipment or Intertool, or Interskol. The young but frisky company Johnsway and Ombra, repainted from green to brown, have great experience and opportunities in this regard.

The catalogs contain a sea of ​​excellent working equipment, fixtures and universal pullers, mandrels for all occasions and, of course, tools that are difficult to look at without a stingy male tear. But the cost in the catalogs is unreasonably high, as for a private trader. Service stations, of course, are in more favorable conditions, they earn money with equipment and God himself ordered them to have a better tool. Otherwise, such a master is worthless.

Garage Craftsman Wish List

Still, it is worth making a rough list of what should be in the workshop, and from it already choose accessories for the garage that you can build yourself. Here's what everyone would like to see:

This should be an approximate set of additional equipment, not counting welding, a compressor, two or three angle grinders and two or three drills and screwdrivers of different capacities.

Homemade fixtures

An elementary frame for a grinder can become a universal home-made machine. Applications - mass, made from anything, up to a solid wooden frame. it will be useful in cases where it is necessary to process a small part carefully and with two hands, without clamping the part in a vise. Of course, this design has limitations, but as a small grinder or cut-off machine, it will work for five.

We do not indicate the dimensions, the designs and sizes of the grinders are different. The photos show the essence of the device, and it is not difficult to assemble it. It is worth working on fixing the grinder to the frame - so that it is quickly and securely fixed and quickly removed. Such a device is especially valuable for angle grinders with adjustable speed.

As a base, we use a chipboard sheet of suitable size, which is hinged, as in this design, or on latches, you can use a screw mount.

DIY lathe

The drawing of a small lathe, which is presented, can be useful to those who occasionally have to deal with turning work, and it makes no sense to buy a desktop one. This project will certainly not satisfy those who need high precision and high spindle speeds, but for minimal turning work it will do. Instead of the spindle from the M10 bolt shown in the drawing, use a finished spindle or drill chuck.

Designed for processing wooden and plastic parts, the diameter of the part is up to 50 mm, and the length is up to 200, but can be revised if necessary. If we take it as a basis, then replacing the wooden base with any metal-roll, we get a kind of desktop machine for turning metal.

Tool Storage

Various trifles are often folded in plastic buckets and boxes in the form of a kind of assortment. Therefore, finding the right small tool, drill or nut is quite problematic. For storing small things, jars of mustard, mayonnaise and other products with a metal or plastic lid that is firmly attached to the jar are perfect.

To organize easy access, you will have to sort through everything, separate the cutlets from the flies, the bolts by 10 from the nuts by 6 and sort everything into jars. Covers are screwed to shelves or any horizontal surface, and now it will not be difficult to find the necessary fasteners.

For horizontal storage of loose fasteners, magnetic containers can be used. Convenient thing. Fasteners will not crumble, always in sight, and containers can be arranged as space requires. The main thing is to fix a thin magnetic tape in the right place, and glue large metal washers to the bottom of the containers themselves.

More creative ideas that come to mind inventive craftsmen regarding the organization and storage of tools and fixtures, we have shown in the photo. Use your imagination and reinvent the wheel. And your garage will be the perfect place for a comfortable repair of your favorite car.

Read also Electric heat guns for the garage, Do-it-yourself lifting garage doors - drawings

ladamaster.com

How to make homemade garage fixtures: 2 workshops

Home-made devices can be made from improvised materials Car repair is a complex and responsible task that requires practical knowledge and the availability of special equipment. This equipment includes a whole list of tools that are not cheap. That is why even those motorists who know how to fix their four-wheeled friend give it to a car service for repairs. If you decide to get your own accessories for the garage, but do not want to spend a lot of money on such purchases, you can do some of the list of necessary things with your own hands.

So that your garage can become a place for car repairs. It needs to be equipped with a large number of different tools. Some of them will have to be purchased in specialized stores, but others can be made with your own hands.

Having all the necessary fixtures and machines for the garage, you can open your own small car service. Such a garage business will bring you good income.

Garage accessories are easy to do with your own hands. In fact, there are many master classes for the manufacture of such homemade products. Let's see which tools are made on their own most often.

What homemade tool is suitable for a garage car service:

1. First of all, it is a car lift. Not a single car repair shop can do without this equipment. The price of such a finished device is high, but if you wish, you can make it yourself. Today we will talk about the technique of creating such accessories.
2. A hydraulic press is also needed for the garage auto repair shop. Such a device helps to compress unnecessary parts. You will be pleased to know that you can make it yourself with minimal investment.
3. Useful accessories such as a spotter comb are also important. Such equipment is easy to manufacture, but in finished form it is very expensive.

For a car service with your own hands, you can make metal shelves that can be moved

These are not all the fixtures that you can make for your garage with your own hands. However, it is precisely the described useful homemade products that we will make today in our master classes.

Garage Accessories: Room Improvement

Before we start describing how to make garage accessories, we suggest putting things in order in the auto repair shop itself. After all, each tool should have its own place, so it will be easier for you to work.

Homemade tools are very practical, but do not always look aesthetically pleasing, so it is better to remove them from prying eyes. But, for example, such a device as a drilling machine and jacks can be put in a prominent place.

You can't make a drilling machine with your own hands. In this case, the main thing is to choose the right tool correctly.

Now more about the organization of the workspace. If you decide to make a car repair shop in the garage, and make money from it, then you will have to prepare the space accordingly.

How to organize tool storage space in the garage:

1. First of all, we advise you to make some wooden boxes. In some of them, you can make a shelf with holes for screwdrivers.
2. It is also necessary to make mobile racks for heavy tools. This will allow you to change the location of these shelves, putting them in a convenient place for you.
3. So that in the process of work, you do not have to constantly run after the tool, you can use a special belt that will fit the essentials. Such devices can be bought or made independently.

These homemade tool storage spaces will help you organize your garage space. Thanks to this, everything you need will always be at hand. This will save you a lot of time.

Do-it-yourself garage fixtures: making a lift

A lift is needed for every auto repair shop. This device helps to keep the machine in an elevated position for the time you need. Due to this, access to all hard-to-reach areas is opened.

Of course, you can buy a lift in specialized stores. However, the price of such products will unpleasantly surprise you.

The lift for the car repair shop can be made by hand. You don't even need to be a welder to do this. Therefore, you can easily cope with such work.

In order to assemble the lift, you will need:

• Worm gearbox, the load capacity of which will start from 300 kg;
• Steel corners with dimensions of 7.5X7.5X0.8 cm - 2-3 pieces;
• Some number of bolts;
• You will also need a steel plate, at least 1 cm thick;
• Two iron chains, at least 2 cm thick;
• Steel cable with half a centimeter section;
• Metal hook;
• Two dowels in the form of an asterisk.

From such materials it is easy to make a lift without spending a lot of effort. The main thing is to perform all actions accurately and efficiently.

To make a good garage lift, you need to use high-quality metal

How to make a car lift:

1. Steel corners need to be attached to opposite walls. In this case, they should be located on the same level.
2. A plate is attached to the corners. This is done with eight bolts. Thanks to this connection method, the plate can be moved relative to the engine.
3. A worm gear can be installed on the plate.
4. One of the keys, the one with a larger diameter, must be fixed on the gearbox drive shaft.
5. One hole must be made on the plate. A chain is passed through it and closes into a ring.
6. On the output shaft of the gearbox, you need to install a smaller key.
7. A couple of holes need to be drilled in the lift plate.
8. Pass the second chain through the drilled holes. One of its ends is thrown over a smaller key, and a hook is hung on the other.

This completes the manufacture of the lift. You just need to test it in action. Spending a little time on such work, you can save an impressive amount.

How to use a garage tool such as a lift

Using this lift is quite simple. However, in order not to damage anything, you must follow a few rules.

How to use a homemade lift:

1. Unscrew the bolts that connect the machine's engine to its frame;
2. Loops of a steel cable carefully lead under the engine. Throw the ends of the rope onto the hook.
3. Move the chain carefully. Gradually, the cables will stretch, which will set the engine in motion. Perform all actions slowly and smoothly.
4. When the engine is raised to the required height, the lift can be stopped. The gearbox will hold the structure.
5. In the place where the car flocked, it is necessary to put a table that can withstand the weight of the engine.

Please read the instructions before using the lift.

Using a lift will greatly facilitate your work in the workshop. Therefore, it is worth spending time and making it yourself.

Garage machines: we make a hydraulic press

The hydraulic press is often used in auto repair shops. It is necessary for installation and repair work. Such a device works on the principle of a jack.

Such a device can be very expensive. Some models can cost several tens or even hundreds of thousands. It is because of the cost of a factory product that a hydraulic press is often made by hand.

There are several positive aspects of making a hydraulic press with your own hands. Let's get to know them in more detail.

Why making a DIY hydraulic press is a good idea:

1. A homemade hydraulic press can be made specifically for the work you need. This applies to both its size and its performance.
2. You can assemble such a jack from improvised materials. Therefore, the price of such an assembly will be low.
3. You can be sure of the quality of the assembled product. If necessary, it can be repaired.

The hydraulic press is made of a jack, channels, two metal corners, bolts and springs.

From time to time the hydraulic press should be inspected for worn or damaged parts.

The assembly of the structure is carried out according to the scheme. All elements are fixed by welding and bolts. It is very important to position the jack in the correct position.

Homemade garage fixtures: making a comb

We want to tell you about the manufacture of the comb. This spotter tool can be used to smooth out dents in doors. It can be purchased in specialized stores, or do it yourself.

How to make a comb for a spotter with your own hands:

1. Take a metal strip and make three holes in it. The first should be at a distance of 1.5 cm from the edge, the second at a distance of 2.5 cm, and the third - 3.
2. Now between the two holes (which are closer to the edge), you need to saw through the jumper with a file. After finishing this work, instead of two round holes, you should get one oval one.
3. From the third hole we make a cut to the edge. You should get a notch for the washer.
4. Now we cut out a kind of semicircle above the hole made. As a result, you should get a hook with an oval hole and a rounded notch. Make four more such details.
5. Take a tube with a diameter of 1.5 cm. At a distance of 2 cm, drill a hole with a diameter of 8 mm. After two cm, cut off the tube.
6. On the other tube, make a semicircular recess, our workpiece should ideally fit into it.
7. We weld the tube with a notch to the workpiece so that the hole is on top. A nut must be welded to this hole.
8. We take another tube, weld a washer on one side, and put our hooks and workpiece on the other. The comb is ready.

Such a comb is no worse than a purchased one. It does its job well and is inexpensive.

Do-it-yourself garage accessories (video)

Garage accessories are not difficult to make with your own hands. To do this, you need to apply only diligence and ingenuity. Dare!

Examples of do-it-yourself garage fixtures (photo)

Attention, only TODAY!

oteplicah.ru

Homemade machines and accessories for the garage. Read the article!

By making home-made machines and accessories for the garage with your own hands, you significantly save your own and family budget. Homemade shelving, various furniture, workbenches and even some tools - all this can be done independently.

Self-made garage machines are needed to solve the following tasks:

• Simplifies the process of processing metal products,
• There are new opportunities for grinding and processing wood,
• A machine in the garage allows you to save on the purchase of an electric saw and other woodworking tools.

As a rule, any of the racks or power tools is quite expensive in the construction market. That is why the owners of garage boxes come to the idea of ​​​​creating some fixtures on their own. The most popular options for homemade homemade tools are:

• Manual or semi-automatic joiner's workbench for metal;
• Wooden or metal workbench;
• Drilling machine for garage;
• Homemade press design;
• Various variations of shelves, racks and organizers for tools;
• Hoist or winch for lifting heavy parts and things.

How to make drilling machines in the garage with your own hands?

Drilling machine for garage

Thanks to this homemade device, you can perfectly cope with the manufacture of any number and diameter of holes for metal and wooden objects right in the garage workshop. The simplest and at the same time reliable option for manufacturing a machine is to use a drill with a bed. To make the device you will need:

• Metal frame in the form of a base;
• A small mechanism for imparting rotation to the drill;
• Low vertical stand for attaching a drill.

In the form of a rack, it is best to use trimmings from chipboard or unedged boards. Due to the low weight of the drill, there is no need to use a metal profile. At the same time, it is better to use a cast-iron base for the bed - it will allow you to avoid any vibrations during the operation of the equipment. In the video you can see how to make homemade machines for the garage with your own hands.

How to make a carpentry vise in the garage?

To create a vice with your own hands, you will need to connect the following elements in the correct sequence:

• Several supports, each of which will be a sponge for clamping the product,
• One metal clamping jaw,
• A set of steel guides that are used for smooth movement of the sponge,
• Lead screw design
• An element called a crank that sets the screw in motion.

The first support from the pipe will act as a kind of body. It will be necessary to solder other supports to it from below and install a steel flange. Especially for the movement of the running nut, we drill a hole and, on the contrary, weld the sponge. For the operation of the equipment, it remains only to install a stud in the holes, fix it with nuts and insert a movable tube next to it. As a result, making a vise for a garage with your own hands is not particularly difficult.

Forge in the garage with your own hands

If you decide to make a forge in the garage, then you don’t need to buy expensive components for this - everything can be made from improvised materials. The old gas stove will serve as the main for the hearth. We install it in the chosen place, having previously overlaid the base and the construction box with refractory bricks (chamotte) and smeared all the cracks with clay.

The next step is to make a grate. For a mini forge in the garage with your own hands, you can weld it from an old piece of steel. It is advisable to choose a metal of at least 10-15 mm. Further, furs are made for pressurization, the block of which can be quickly put together from thin-walled plywood and several pieces of board.

The last step is to prepare the fuel. Coal can be bought at the store or made by yourself in a trench using a large duralumin pan. To do this, load the chopped firewood, close it tightly with a lid and smear the cracks with the edges with a clay mixture. In the trench, you make a firebox and heat the coal “until ready”. As a result, you get a full-fledged forge in the garage, made by yourself.

Now, from improvised materials and tools, you can easily make things useful for the garage space on your own. If you have any questions - write them in the comments!

The garage is the holy of holies for any car enthusiast. Almost every man who is the proud owner of a garage spends perhaps more time in it than at home with his family. Car enthusiasts and masters of their craft use this kind of premises for work, repair of cars or other equipment, the production of furniture or various useful things for the home, as well as just friendly gatherings with friends. To make your garage as comfortable and functional as possible, men are ready for anything. In this article we will give some interesting ideas on how to make it yourself and thereby simplify your leisure time in it.

To get started you need. In order to properly equip the garage and rationally use all of its rather small space, you can use the following garage homemade products:

• Shelving or stands along the entire length of the wall;
• Shelves (closed or open type);
• Tables with cabinets;
• Overall drawers or shelves for storing large items;
• Hooks and hooks for hanging objects;
• Secret drawers or shelves;
• lockable drawers;
• Metal frames for storing spare wheels and replacement tires;
• Steel meshes;
• Inspection pit for car repair;
• Cellar or cellar for storage of vegetables and conservation.

And now let's look at how to make some of the listed crafts in the garage with your own hands.

Shelves

Such convenient devices as shelves can, of course, be made of wooden boards and metal fasteners. And you can use the life hacks of other motorists - make shelves for storing nails, screws, bolts and nuts from plastic bottles:

• If you need open holders for all sorts of small things, then you need to cut the base of a plastic jar or small bottle in half, without touching the threads. Then the thread must be screwed into the lid of the container and the outer side of the lid must be glued or screwed to the wall so that the cut-off part of the bottle looks up. As a result, the remaining part of the container will serve as a kind of holder for various kinds of stuff.
• The same small parts and materials can be stored in closed plastic containers. To do this, it is only necessary to glue or screw their lids to the shelves from below so that the can is in a vertical position. When you need to take something from the container, it will be enough just to unscrew it from the lid.
• In general, any home or building material can act as a shelf in the garage. So, for example, a piece of sewer pipe or a cardboard cylinder, mounted on a wall or under the ceiling, can be used as a great place to store long items. And the halves of plastic plates screwed to the wall will serve as convenient pockets for discs for the grinder.

Shelving

In order to store tools, things and various accessories of the owner of the garage, it is advisable to equip it with a large and durable rack. This kind of homemade in the garage can be done in several ways:

• The most reliable is a rack made of metal and wood. Steel rails provide a solid base and support for wooden shelves. Shelves made of steel will be even stronger and more durable.
• You can also make a rack with your own hands in the garage completely out of wood. To do this, you need a medium and thick board (19cm). It is necessary to cut supports for the rack from the middle board, and to make shelves from the thick board. It is necessary to fix all the details of the structure with screws, and open its surface with oil varnish.
• The most budget homemade garage racks can be made from 50x100 timber, 50x25 boards and plywood. The timber in this structure will act as legs, boards - transverse guides, and plywood - shelves.

Attention! Do not place on a do-it-yourself rack tools and things whose total weight exceeds 500 kg. This kind of useful home-made for the garage is designed to withstand a mass of up to 200 kg.

boxes

One of the "Kulibins" became the author of such an invention as boxes in the form of cut plastic canisters. If you carefully cut off the side wall of the canister and put it on the shelf with the opposite side, then such a container can easily turn into a drawer with a handle.

Frame for storing winter tires and wheels. Such a frame can be equipped with metal corners. The corners must be connected to each other with any metal-roll product. If a suspension frame for wheels is planned, then two triangles must first be built from the corners, which will subsequently be connected by two more corners. The connecting corners will act as wheel holders, therefore the distance between them should be such that the wheels do not fall into it, but only sag a little. If it was planned to make a standing rack for wheels, then a rectangular frame is simply made from the corners.

Other homemade

Here are a few more homemade things that you can build in the garage with your own hands:

Let's hope that thanks to the photos in the article, useful tips and instructions, you can easily build home-made products with your own hands for a garage or other utility room.

Most car owners spend at least two hours a day caring for their car, and even more on weekends. If we talk about something major, for example, engine repair, then we can talk about several days. For this reason, it is extremely important that the environment in the garage is as comfortable as possible for work.

Arranging a garage is not as easy as it seems, because in addition to spare parts and tools, it usually stores everything that does not fit in the apartment. Moreover, any repair is pollution, which sooner or later turns the garage into a very unattractive place. In a word, even during construction, you need to think about how the garage will look in the future, how best to combine a workshop and a miniature warehouse in it.

First you need to decide on the main tasks. First of all, the garage should always be clean, so you need to use non-staining and easy-to-clean materials for finishing. It is also required to draw up a layout of the location of tools and equipment in advance, that is, determine where the racks, shelves, workbench, etc. will be located.

Stage 1. Interior decoration

In this regard, a number of requirements are imposed on finishing materials. Materials must be:

• non-combustible;
• resistant to mechanical damage;
• able to withstand exposure to aggressive chemical environments;
• pollution resistant.

Moreover, they should be easy to clean and not absorb odors. Obviously, not all materials have similar qualities. Those that still possess them include plaster, wall paneling and ceramic tiles. Each option has its strengths and weaknesses, let's get acquainted with them.

1. Plaster

Ideal if you want to hide uneven walls. Plaster will effectively hide all existing defects and ennoble the interior of the garage.

Note! The plaster must be covered with a layer of facade paint, otherwise the surface will begin to crack and crumble.

2. Lining

Lining is used mainly in the northern regions of the country, since it is very convenient to place thermal insulation material between it and the profiles. In this case, it is better to use a facade profile, made of polyvinyl chloride - it is fireproof and waterproof.

The only drawback of lining is low strength - after a strong impact, the panels are deformed and need to be changed.

A more laborious and costly option. It requires a preliminary calculation of the strength of the walls, because the tile weighs quite a lot.

At the same time, ceramics do not burn, are easy to clean and are characterized by increased strength. If the garage will be sold in ten years, then it is better to decorate it with ceramics. Expensive, of course, but for a long time.

Stage 2. Observation hole

To repair the machine, it is desirable to equip a viewing hole. Even the smallest breakdown becomes a serious test if it is impossible to reach it without a viewing hole. In such cases, you have to go to the service station and pay a considerable amount for repairs.

In a word, the arrangement of a viewing hole will soon pay off. Below is the sequence of actions.

Step 1. First, the dimensions of the future pit are determined and marking is carried out. At the same time, a balance must be struck - firstly, the pit must be spacious enough, and secondly, its width must be such that there are no problems when entering the garage.

The required width is 0.7 m, it will allow you to feel comfortable during repairs and at the same time leave enough space for parking maneuvers.

Note! When marking, you need to leave a margin of about 20-25 cm for the wall thickness.

With regards to depth, it depends on its own height, but again it is better to make it a little deeper than required - it is much easier to equip additional flooring than to redo the floor when deepening.

Step 2. Upon completion of the markup, you can start earthworks. The most difficult thing is to dig a hole, because more than 9 cubic meters of soil will have to be removed.

Step 3. The floor is leveled and covered with a 25 cm "cushion" of crushed stone. It is noted where the niches for the tools will be located.

Step 4 Walls can be poured with concrete or overlaid with bricks. Concrete is more reliable, so it will be considered.

First, the floor is poured, a thickness of 7-8 cm will be enough. For reliability, you can pre-lay reinforcement. Next, a wooden formwork is being built, which will be gradually filled with mortar in 40 cm tiers. The upper edge is reinforced with a metal structure, lamps are installed.

Note! It is advisable to cover the concrete floor with a wooden ladder, because it will be much more pleasant to work on such a surface.

Stage 3. Shelving

For ease of use, each tool should have its own place. Shelves and racks can be bought ready-made, but they are quite expensive, and they do not always meet the needs of the car owner. Therefore, the rack is better to do it yourself. It seems difficult, but only at first.

Step 1. First, the dimensions are marked. Most "shop" racks are equipped with shelves 1 m wide. This is not enough for spare parts, so the width needs to be made larger.

You also need to leave a gap of at least 20 cm from the floor so that there are no difficulties with cleaning the floor. It is desirable to perforate all shelves - this will give two advantages at once:

Step 2. For the manufacture of the rack, a metal frame is used from a profiled pipe or a 30x30 corner. The parts are welded or bolted together, then the shelves are cut out. Usually, boards are taken for this, but moisture-resistant plywood is the best option - it costs more, but it will last a long time.

Stage 4. Shelves

Like shelving, shelves are best done on your own.

Step 1. First, the number of shelves, their dimensions and installation locations are determined.

Step 2. In accordance with the calculations, everything you need is prepared:

Step 3 Using the mounting level, the attachment points are determined. Next, holes are made, dowels are hammered into them.

Note! For reliable fastening, it is advisable to use dowels with hooks.

Step 4. With a certain step (in accordance with the holes made earlier), suspensions with lugs are fixed on the shelf. They can be nailed with ordinary nails. The assembled shelves are hung on dowels.

It is worth remembering that the hinged shelves should not be too long, otherwise they will break under the weight.

Stage 5. Garage workbench

The most convenient for the garage will be a workbench that combines shelving and a work surface. So the tools will always be at hand, which will significantly reduce the time spent on searching for one or another of them.

For the manufacture of a workbench, a metal frame is assembled, on which a wooden tabletop with shelves is installed. The tabletop is covered with sheet steel so as not to damage the structure during operation.

The workbench must be equipped with several sockets for electrical tools, as well as a fluorescent lamp, equipped with iron brackets for this.

Video - Garage workbench

Stage 6. Garage cellar

Often garages are equipped with cellars in which conservation is stored. This moment, as well as a viewing hole, must be thought out in advance.

Step 1. First, the old flooring is removed, after which all the pieces are removed, and the garage is cleared for digging a foundation pit.

Step 2. Next, earthworks are carried out. In this case, special attention should be paid to the type of soil, because if the soil is sandy, then with careless digging, the walls of the room can collapse. That is why it is desirable to use a variety of props made of wood and metal.

If the soil is clayey, then you can not be afraid of anything, because it is able to withstand any load.

Step 3. The bottom is covered with rubble and carefully rammed. Next, fittings are installed, the floor is poured with concrete mortar.

Step 4. The walls are built of bricks.

Step 5. The cellar is covered with a reinforced concrete slab, after which waterproofing is laid - bitumen or roofing material. For insulation, you can use any thermal insulation material.

Note! The cellar can be equipped even if the level of groundwater is high enough. To do this, a metal tank is welded throughout the pit. When the water level rises, the tank will rise, and in summer it will simply lie on the bottom.

Step 6. It remains only to take care of the ventilation of the cellar. To do this, steel pipes (2 pcs.) Are removed above the ground level, preferably on opposite walls of the structure. The supply pipe is located below, and the exhaust pipe, respectively, under the ceiling. Both pipes must be the same diameter.

A few words about ventilation in the garage

Such ventilation, it would seem, is not needed, but without it a lot of dust will accumulate in the garage, which negatively affects not only the body, but also the internal parts of the car. And exhaust gases are harmful to the body.

The simplest and most affordable option is natural ventilation. Two holes are equipped for it (the same as for the cellar). For maximum efficiency, the inlet and outlet pipes must be installed diagonally opposite each other.

Video - Examples of arranging a garage

Results

It is possible to equip a garage on your own, although this will require a lot of time and effort. But the result will more than pay for all the costs, because in the end you will get not only an autobox, but also a miniature workshop. The garage will become a place to relax or bold experiments with the car.

Read the article on our website - do-it-yourself press for the garage.

An ideal garage should organically combine the functions of a reliable shelter for a car and a well-equipped place for various repairs and other work. There are a number of useful recommendations for the interior arrangement of the garage, while most of the necessary fixtures you can do yourself without spending money on buying them.

The work on the internal arrangement of the garage involves the use of many different useful devices. Read the suggested instructions, and your garage will become the most convenient and comfortable.

Usually in the garage you have to store not only the car, but also a lot of tools and other accessories. For convenient placement of all this, you need to equip the garage with racks, shelves, hooks and other similar devices.

The best option is a spacious shelving. You can do it yourself. Fill the remaining free space with convenient shelves. There is nothing complicated in their manufacture either. You will receive more detailed instructions below.

Get familiar with your tools. Arrange them according to frequency of use. What you use most often should be stored in the rack drawers closest to the workbench. Store heavy equipment on the bottom shelves of the rack, for spare tires, allocate a place near the ceiling - you will need them less often.

Fasten the brackets

These tools will help you conveniently store replacement tires. Brackets should be placed closer to the ceiling, so the wheels will not take up usable space. For tires, buy large bags, or better - special covers to protect against dust.

He's a workbench. The design is easily assembled with your own hands from boards and bars. On the table, you can fix a vise and other tools necessary in the garage. It is more convenient when the workbench is installed next to the shelves and racks.

Properly organize the lighting system

You will need several lamps: above the place where the hood of the car is usually located, above the desktop, in other important places in the garage. Ideally, the lighting system should be organized so that you can turn on all the lights at the same time and each of them individually. This will help you make an ordinary double switch.

Install an outlet close to the garage door and above the workbench.

Allocate space to store the worksheet. One shelf or at least an elementary hook will be enough. There is also a place to store work shoes and personal protective equipment.

Security questions

In the garage, substances such as gasoline, oil, etc. are stored. To store them, you need to allocate a separate locker or at least a shelf near the gate. Place a box of sand nearby and hang a fire extinguisher on the wall.

Each tool in the garage must have its own place, otherwise there will simply be no order in the room. To organize convenient storage of things, assemble a homemade rack. Ready-made models are quite expensive, and they do not always meet the needs of a particular person. Therefore, it is much more profitable and more rational to make a rack immediately “for yourself”.

Collect the rack in such a way that it can withstand a load of at least 150 kg. In this case, the load on each individual section should not exceed 500 kg. The rack can be assembled from wood or metal. The design can be straight and angular.

From wood, preference should be given to the most durable species such as oak, hornbeam, beech, etc. Before assembly, all wooden structural elements are treated with antiseptic impregnation. Thanks to this treatment, the wood will be more resistant to moisture and a variety of bacteria and will last much longer.

If possible, cut and grind all the elements of the frame with high quality.

Shelves are made of plywood or chipboard. DVL and OSB boards are also suitable. The main thing is that the plate has a thickness of at least 4 mm. The higher the expected load on the shelves, the thicker they should be.

To give the shelves a more presentable look, it is recommended to paste over them with a decorative film or paint them. Also, such processing will allow you to better get rid of pollution in the future.

The simplest rack is made in a few steps. Do each one in sequence. Below are the various sizes. You can stick to them or change the dimensions at your discretion.

First step. Take a board 9 cm wide and cut it into several pieces of different lengths: 30 cm, 27.5 cm and 18 cm. From these pieces you will make spacers.

Second step. Take a board 19 cm wide and cut it into the desired number of pieces 36 cm long. From these pieces you will make shelves for your shelving.

Third step. Mark on the board that serves as the base, places for attaching spacers. Spacers are recommended to be installed at a distance of 2.5 cm from each edge of the base. Glue the top brace, then nail the top shelf with the pre-attached brace to it. Do similar manipulations with the remaining spacers and shelves. The bottom strut is attached last.

Fourth step. Turn the rack over and tighten the spacers with the base of the structure using screws.

Fifth step. Thoroughly sand all wood surfaces and apply a double coat of oil varnish. If desired, you can paste over the shelves with a decorative film or finish with other material at your discretion.

Sixth step. Attach the rack to the wall with anchor screws. Fasteners are placed under the lower and upper shelves.

According to this scheme, you can assemble a rack from the required number of sections. To strengthen the structure, place wooden blocks between the sections. This will contribute to an even distribution of loads throughout the system.

If there is no place to install a full-fledged shelving, or, on the contrary, you have installed shelving and there is little unoccupied space left, be sure to make some convenient and simple shelves for storing a variety of accessories.

First step. Decide where to place the shelves. In accordance with this, set the desired number and optimal dimensions of products.

Second step. Prepare the required number of boards and fasteners in accordance with the plan drawn up in the last step.

Third step. Mark on the walls where the future shelves will be attached.

Fourth step. Armed with a puncher, prepare holes in the walls in accordance with the markings and screw the dowels into them. It is best to use dowels with hooks - they will provide a more secure fixation of the shelves.

Fifth step. Attach eyelets to the board. When choosing a distance, be guided by the markings on the wall. Use self-tapping screws to fasten metal hangers. In their absence, you can get by with ordinary nails.

Metal shelves

Garage metal shelves

Metal shelves

Sixth step. Fix the finished shelves to the places intended for them.

Remember: it is better to make several short shelves than one long one that will break under the weight of the items placed on it.

If desired, you can perform a decorative finish of the shelves, for example, paste over them with a film or paint. Make sure the shelves hang straight. A tool called a level will help you control this moment.

To make working in the garage as comfortable and productive as possible, assemble and install a workbench in a convenient place. Behind it, you can repair both car parts and other household accessories. A homemade workbench has a great advantage over a ready-made factory-made model - you can make a table of the size that you need.

Workbench kit

1. Boards.
2. Bars.
3. fasteners.
4. Plane.
5. Ties.
6. Tool for woodworking.
7. Joiner's glue.
8. Sandpaper.
9. Drying oil.

First step. Consider the optimal design of the workbench. The main elements of such a product are the underframe and the tabletop. The design also includes one or more clamping devices.

Second step. Assemble the tabletop. The best option is a tabletop of 20 boards measuring 200x10x5 cm. Prepare grooves for stops measuring 2.5x2.5 cm in the 5th and 16th boards. Place the grooves in increments of 25 cm.

Use glue and metal ties to connect the boards. Before gluing, the surfaces of the boards must be trimmed.

Third step. Carefully plan the dried countertop. It should be a flat, flat surface. Over time, the wood will shrink. You need to not miss this moment and tighten the nuts on the ties in a timely manner.

Fourth step. Make legs. To do this, use high-quality bars measuring 80x10x10 cm. Make grooves for the brackets in the front supports. The brackets will later be connected to the longitudinal beam. This kind of beams are commonly used in the construction of window frames.

Fifth step. Assemble the base of the underframe from two frames and fasten it to the supports. Assemble frames from 10x5 cm boards. Use a spike connection. The frames directly cut into the table legs to a depth of 2.5 cm and are bolted to them. Attach a plywood sheet to the bottom frame. A sheet 1 cm thick will suffice.

Sixth step. Attach the side and back support walls to the table. For the manufacture of walls, use chipboard or plywood 1 cm thick. To the left of the table, build a convenient cabinet with a hinged door.

Seventh step. Attach the workbench top to the top frame with bolts. It is recommended to prepare the holes for the bolts in advance - it will be faster and easier to make connections. Tighten the bolts so that their hats are recessed into the wood.

Eighth step. Make a chair. This device will help you in the future to cut workpieces at the required angles. The miter box is assembled from 2 cm thick wooden strips. Attach the finished miter box to the table using stoppers.

Ninth step. Treat your homemade workbench with drying oil and varnish. Let the paint dry and you can start using the table. If necessary, install a vise on it or, for example, a circular saw. At this point, focus on your needs.

Video - DIY garage accessories