Crane for removing the engine what material. Garage: homemade lifting devices. How to get an engine out of a car in a garage without the help of a car service

Dear visitors of the site “ Labuda blog»From the presented material you will learn how to independently assemble a hydraulic garage crane goose, consider the drawings, step-by-step photos of the assembly, as well as a video of testing a homemade crane for dismantling the engine.

Every motorist, in his practice of operating a car, probably faced engine breakdowns, and not rarely with its replacement or overhaul, but in order to remove the internal combustion engine from its seat, a reliable winch or crane is required. The purchase of special equipment will cost at least 10 K, and not everyone has such an opportunity to install a winch on the garage ceiling, because the garage floors are rather weak.

It is quite possible to make a crane of the "goose" type with a hydraulic boom lifting system independently, for which you need 7 meters of 80x80 mm profile and 3 mm wall thickness. A pair of pipes 89 by 700 mm and 76-900 mm. Jack five-ton 5t, plates 8 mm thick 4 pcs. In this case, the author bought only 2 pcs of ordinary wheels, 2 pcs of swivel wheels, 1 m of M-14 studs.During the tests, a home-made crane calmly lifts 250-300 kg, concrete curbs with a total weight of 500 kg were also transported, everything is fine.

Device and principle of operation the homemade hydraulic crane "Goose" is essentially quite simple, and the name itself speaks for itself) It consists of a support (collapsible) with wheels for moving around the garage and rolling under the car, a vertical stand with a jack and directly the retractable boom itself with a chain and a hook ...

Lift height of short boom at bottom 90 cm at top. Long boom, bottom 80 cm, and at the top 1800 mm and with the unscrewed jack rod, the bottom is 1400 mm and the top is 2250 mm.

So, let's look at what exactly is needed to assemble a garage crane?

Materials (edit)

1. professional pipe 80x80 7 m long
2. pipe 89 mm by 700 mm 2 pieces
3. pipe 76 is 900 mm long
4. wheels 6 pcs, 2 swivel, 2 regular and 2 with a brake
5. metal plates 8 mm 4 pcs
6. jack 5 t
7. chain and hook, M-14 hairpin length 1000 mm

Tools

1. welding inverter
2. LBM (Bulgarian)
3. drill
4. set of wrenches

Do-it-yourself step-by-step instructions for assembling a hydraulic crane goose.

First, you should familiarize yourself with the drawings and diagrams, and then proceed to the assembly.

First, the butt part of the support is made, it will also be collapsible.

A vertical post is welded with a spacer in the lower support plane.

Installation and fastening of the jack.

Full reach boom.

Garage experiment, scooter lifting)

Moped weight 120 kg

It is quite possible to make such a crane with your own hands at minimal cost. Simple, budgetary and compact, because the crane is collapsible.

Thank you for your attention!

Do you have to remove engines from cars or transport heavy items? Then it is vital for you to have such a thing as a small crane! And this is not a thing, there are such taps and you can make them yourself! We will analyze the design of one of them in this article. With this crane, you can easily and easily remove the engine from the car and put it on the table for a major overhaul. Agree, it sounds tempting!

It is not difficult to make such a crane, it is even very simple. The whole structure is welded from steel square pipes. As for the working body, it is used as it. That is, you do not need any electricity, nothing like that, we lift weights, just working with a lever on a jack. As for the technical characteristics, in general, the jack is capable of lifting weights up to 4 tons, but at the same time we take into account that we lift weights through the boom, that is, to a greater height. The experiment showed that such a crane can lift a motorcycle with a sidecar weighing more than 300 kg. With such a load, the structure was slightly deformed, but then the author strengthened it and now 300 kg for the crane is not the limit, but he does not need more! By the way, the jack can also be used with a conventional one; a hydraulic jack is not required. Let's take a closer look at how to make such a crane!

Materials and tools used

List of materials:
- steel pipes of square section;
- ;
- Sheet steel;
- nuts, bolts, etc.;
- dye;
- hook and rope;
- wheels.

Tool list:
- grinder;
- welding machine;
- drill.

Crane manufacturing process:

Step one. Frame
The frame is welded from square steel tubes. Of course, the stand and base should be as strong as possible. To be able to change the angle of the boom, we drill holes in the rack and boom and weld pipes in their places as bushings. This design creates a secure connection. All this is connected with a steel rod or bolt and nut. The base is a crosspiece. We strengthen the rack with pipe sections.

We fasten the wheels to the base so that the crane can be transported with a load. These wheels are installed on garbage cans (but don't steal better).

Step two. Jack
To install the jack, you need to prepare stops on the boom and on the rack. The stops must be movable, since the angle of the jack will change during crane operation. How the jack is installed, look at the photo. Also, now you notice that the author has slightly altered the base, now it has become stronger.

Step three. Arrow
Our boom is retractable, it consists of a piece of pipe with a smaller diameter with a number of holes. We extend the boom to the desired distance and fix it with a bolt and nut. We attach a cable and a powerful hook to the end of the boom.

After painting, the crane is ready for testing. From the author, he easily lifts a motorcycle weighing 318 kg. In conclusion, the author strengthened the post and arrow a little more. So now the strength of the crane should be enough to lift a load weighing 400-500 kg. That's all, the project is over, I hope you enjoyed it. Good luck and creative inspiration if you decide to repeat it. Do not forget to share your best practices and

A do-it-yourself garage crane goose can be made from scrap materials that are available in the garage. This device is required when the vehicle needs to be repaired, such as removing the combustion engine from the vehicle.

Necessary materials

The crane is made from a profile with a length of 7 m. It is best to use a material with a wall thickness of 7 mm. The mechanism must be durable, so it is worth choosing a profile with a section of 80 × 80 mm.

Several pipes are also required to make the hoisting device. Products of 700 mm are suitable, the cross section of which is from 76 to 99 mm.

For the construction of a crane, you will need a jack, you can take it from a VAZ. It is best to use a device that is designed to lift loads weighing up to 5 tons. For the construction of the mechanism, 4 plates with a thickness of 8 mm are required.

For self-assembly of the crane, you need to have the following set of tools:

• drill;
• inverter for welding;
• spanners;
• grinder.

The assembly of the mechanism is not difficult, so it is easy to do it yourself. or any other device after assembly can be painted.

Assembly instructions and drawings

The design was named "goose" because of its L-shaped shape. The mechanism is easy to use, because thanks to it you can bring the boom to the engine compartment. This reduces labor costs for connecting the motor, which shortens the repair time.

The goose design is simple. The mechanism consists of a collapsible support equipped with wheels. With their help, it is easy to move it from place to place, roll it under the car.

The device for the garage has a vertical stand, a jack is installed on it. "Goose" has a retractable boom, which is equipped with a chain with a hook. When the jack is activated, the boom goes up, lifting the load.

A hydraulic crane is most commonly used to lift an engine. The device can be made according to ready-made drawings, but most often a hand-drawn crane diagram is used, even beginners will draw it with their own hands.

See " The procedure for registering a crane in Rostekhnadzor and the documents required for this

First, a collapsible part of the pore is made, it is a butt one. After that, the vertical post is welded. At the bottom, a spacer must be installed. After that, proceed to the installation of the jack, it must be securely fixed. The arrow is made for full reach, it is needed to remove the engine. All parts of the structure are welded. The result is a robust yet manoeuvrable device.

When the product is ready, tests are required.

For this, a load is suspended, which should be 20% heavier than the one that needs to be lifted. If the mechanism can withstand the load, it can be used in operation. The goose crane is collapsible, so it does not take up much space in the garage.

How to use

The telescopic arm of the mechanism can be installed in several positions. The goose is maneuverable, it can be driven by 1 person. The equipment lifts rather heavy loads due to the installed jack; no additional accessories and devices are needed to move heavy loads.

For repair work on the car engine, a lifting device was needed, a craftsman from Novosibirsk decided to make a homemade crane with his own hands.

As planned, the crane should be collapsible so that it does not take up much space in the garage. The lifting will be carried out by a hydraulic jack.

The photo shows the construction of a homemade product.

The base is welded from a 60 mm channel and a 50 mm square pipe, additionally trims are used to strengthen the structure.

The channel is welded at an angle to which the vertical column is deflected back.

Rack vertical and boom from a square tube 50 mm.

Legs and boom reach are made of 40mm square tube.
Drilled holes for the upright, legs, and arrows for the outreach. I put my ear under the jack and figured out how the jack would fit on the stub of some kind of metal structure. The boom has a 30mm corner reinforcement.

Shoulder - 1/5, approximately 110 cm of the boom and 22 cm of support from the axis of the upright.

In the photo, the rise is 130 cm to 210 cm. The boom can be moved plus, depending on the carrying capacity. You can also unscrew the screw from the stem on the jack. The jack is designed for 3000 kg, therefore the weight on the boom is 600 kg maximum (arm 3000/5).

During the tests, the vertical console began to bend (between the lower channels and the lower jack stop). Motor + gearbox, 250-260 kg. I had to reinforce, weld 5 mm sliced ​​plates onto the 50 pipe.