Garage Ideas: DIY Gadgets for the DIYer. Making homemade products for the garage DIY garage gadgets

For the rational use of space, communications and devices for the garage are used with their own hands from scrap materials. It is necessary to use walls, an underground level in the process, place machines inside the room, organize normal lighting.

DIY garage accessories

For the comfortable operation of a room intended for storing a car, you should adhere to certain recommendations:

the tool must be as accessible as possible;
storage areas equipped with shelves / racks are much more convenient;
do-it-yourself workbenches, a viewing hole, home-made machines and garage accessories expand the capabilities of the car owner;
the cellar allows you to save space on the site;
the quality of lighting depends on the productivity of work, minor repairs.

Organization of the working space inside the garage

Depending on the size of the building, the area occupied by equipment, fixtures, and communications should not be more than 10 - 20% of the size of the garage floor.

Storage locations, racks, workbenches

In 80% of cases, do-it-yourself garage fixtures are constructed to store accessories, tools, and vehicle equipment. It should be borne in mind that the most bulky parts of the car are sets of winter / summer tires, depending on the season.

Tire storage rules

It is more convenient to store wheels on brackets of the following design:

two triangular frames from the corner, connected by jumpers from any rolled metal;
the triangles are attached to the wall, the wheels are installed perpendicular to the supporting structure, falling slightly between the lintels.

Wheel storage brackets

This is the most economical option for storing rubber during the off-season. Straight and corner workbenches are most in demand by car enthusiasts. The lower space is usually filled with shelves or drawers, sharpeners and vices are located on the table top.

Homemade garage workbench

An example of organizing a corner workplace

A folding workbench can be very convenient.

Wood is a versatile material for both workbenches and shelving

A wooden workbench is easier to build on your own, but it has a lower resource than an analogue from rolled metal, which needs to be welded. If no corners for shelves are laid in the load-bearing walls during construction, it is easier to make racks from rolled metal or sawn timber.

Homemade garage racks

Use for glass bottle racks

Built-in wardrobes are very compact

Original hanging shelves are suitable for storing long items

The design and arrangement of shelving within each garage is too individual to follow general guidelines.

Inspection pit and cellar

An inspection hole becomes a necessary device for a garage with your own hands. Moreover, the owner does not have to make all the repairs on his own. Underground communication can be used in the following cases:

inspection of the chassis, steering, brake system before a long trip;
oil change that saves money, does not take much time;
minor repairs that allow for the qualifications of the owner.

Inspection pit in the garage

It is more convenient to enter the cellar from the pit, as this will allow several steps to be concreted instead of using a ladder.

Cellar under the garage

The main nuances of these designs are:

swelling of clayey soils is harmful to underground structures;
therefore, all elements of the pit and cellar are insulated with expanded polystyrene outside;
in the underlying layer before concreting, backfilling the sinuses of the pits, sand or crushed stone is used;
along the perimeter of underground structures at the level of the sole, drains are laid to collect and drain water.

The width of the pit should allow the driver to enter it without lighting.

Lighting and ventilation

In garages, parallel lighting circuits are more often used. One lamp allows you to use a specific area, several devices are turned on during major repairs, visiting the cellar. The minimum power consumption is ensured by LED lamps. Daylighting devices have a great resource.

In cars, poisonous, harmful fuels and lubricants are used, therefore, do-it-yourself devices for ventilation of the garage, allowing you to create air exchange, become relevant. The inflow is organized from below:

garage - air vents in the masonry, protected by gratings;
cellar - a pipe from the garage or from the street.

Ventilation of the garage and cellar under it

The hood is mounted under the ceiling of the cellar, the roof of the garage, or has the form of vents in the main walls at the highest points.

Related article:

Do-it-yourself garage ventilation. From this publication you will learn why garage ventilation is so important, what air exchange schemes exist, and the nuances of installation.

Other helpful ideas

Useful accessories for a garage with your own hands can be made from used utensils, inventory, materials left over from construction. For example, by gluing the lids of plastic cans horizontally / vertically, the owner gets a convenient transparent utensil for tooling or hardware, which is always at hand.

Device for storing small parts, tools, hardware

Interesting PVC pipe screwdriver storage rack

Homemade machines

From a power tool, you can assemble homemade machines and accessories for the garage:

drilling - a drill fixed with clamps in a device moving a gear along a rail;

Drill boring machine

detachable - similarly clamped angle grinder with equipment for metal or wood;

Cutting machine from angle grinder

wood lathe - headstock from a drill, back from a chuck, fixed on a frame made of a square tube.

Drill lathe

The advantage of the machines is a more accurate positioning of the tooling relative to the workpiece. The equipment turns out to be collapsible, the drill and angle grinder can be removed and used as intended.

Related article:

Metal lathe for garage. Machine types, technical characteristics, design, overview of popular models in a special publication of our online magazine.

Hydropress

The simplest design of a hydraulic press is derived from an automobile hydraulic jack. To press out / press in bearings, press / compress parts, you will need to build a frame and a removable movable stop. The frame consists of 4 channels welded to each other. At the top, the structure is reinforced with stiffening ribs (kerchiefs), at the bottom, transverse corners are added, giving the frame stability.

DIY hydraulic press from a jack

The stop is pulled in a normal position to the upper crossbar of the frame by powerful springs. A hydraulic jack is installed between them, if necessary, pressing the stop to the lower crossbar of the frame. The force of the press is regulated by a jack, the dimensions of the working area are selected depending on the size of the workpieces.

And finally, a few more examples of useful things for the garage.

Shelving at the ceiling

Storage pockets for cutting discs made from disposable plates

Device for the convenient use of threads and ropes

PVC pipe trims are ideal for creating convenient storage areas

Convenient pull-out racks for storing tools

Interesting homemade products for the garage with your own hands

The finished "motorhome" over time is overgrown with a large number of tools. Ordinary homemade garage products provide practical benefits without overpayments. Any hand-made machines will not be inferior in quality to factory counterparts. Let's take a look at some of the fixtures.

Knife sharpener

So, a useful device gets a hole for the stem in the bolt. The stem is made by hand from a thin wire. The thread is made according to the length of the whetstones.

A bar clip can be created from:

organic glass;
ebonite;
saw clamp.

The upper part of the plate acts as a clamp. The surface with two drilled holes is applied to the bed. Then a common through hole is made closer to the knife. A thread is cut in the bed.

So, a self-made device with your own hands is almost ready. The second hole is made only on the plate farther from the knife. Then cut the thread for the bolt (needed for tightening). A simple DIY garage mechanism allows you to sharpen your knives in the field.

A block made of artificial diamonds is affordable and very durable.

Pulley for adjusting the speed and load on the machine motor

metal;
textolite;
plywood (something between wood and metal).

One small and two larger circles are cut in plywood with a jigsaw. The center of the molds must match the diameter of the shaft. So that there are no problems with further manipulations, the circles are glued together or sit on the screw and tightened with a nut.

The parts of the useful device are tightened with screws. Then the pulley should be processed with sandpaper or a file, placing the structure on the drill chuck. The finished piece of the machine can be additionally rolled.

Avoid vibration and keep the center of gravity on the pivot.
You can make a gear pulley. Small tubules are made near the central circle until all stages of assembly.
If necessary, a small pulley is made from a thick piece of plywood (one circle). A groove is made in the mold, the part is pushed onto the screw. A narrow file is applied to the rotating wheel.

DIY vacuum forming of plastic sheets

upper and lower frames;
molding plastic;
tie bolts;
perforated MDF;
opening for the discharge chamber;
plywood base with a hole in the middle.

A hole is made in a piece of MDF or plywood (50 by 50 cm) for a PVC pipe with a three-inch diameter. A frame of beams (30 by 30 cm) is attached to the resulting base with glue. To obtain tightness, all cavities are sealed with a sealant.

The edge of the water pipe is glued to the base with one end, and the other is attached to the hose of the vacuum cleaner. The whole structure stands on its legs.

Certain holes are cut in the upper and lower frames to accommodate the vacuum chamber frame (firmly glued to the base). Along the frame perimeter, cavities for fasteners are made at an equal distance.

Types of thermoplastic plastic used:

DIY jigsaw

A steel square with a bolt soldered into it is made by hand as a file holder block.
The redesigned block is soldered to the old saw holder.
Attention is paid to the desktop. Plywood is chosen as the base. The narrow table area is the same size as the jigsaw.
Furniture legs are mounted in the front plane of the table, a small wooden stand is fixed to the back plane of the working area.
Use only hardwoods to create the leverage.
The lever hole needs to be created with a slightly larger diameter of the stud (it regulates the spring tension).

The described self-made craft should stand on a "sole" that will not interfere with the work process. If necessary, cut a corner in the area of the base plate.

A set of cutters for artistic turning with your own hands

A semicircular grooved chisel-cutter is used for rough turning. The part is made from tool steel strips.

The universal cutter is used for finishing parts. The tool is made from standard straight chisels.

Shaped cutters:

chisel scraper.

a tool based on a straight chisel with one-sided sharpening levels the surface of cylindrical workpieces;

a homemade fixture helps to thread and apply decorative marks on a wooden rod.

The cutting tool for soft wood (aspen, linden) has a smaller sharpening angle compared to the sharpening angle of the device for processing boxwood, oak, birch.

Homemade extension cord with two sockets

The "branded" extension reel is made of two plywood discs, which are bolted together. The fragments are separated by a duralumin tube and washers.

On one side of the reel, the bolts are recessed so that contact with the handle is without injury. On the other side, at a certain distance, two holes are drilled for the sockets. The socket boxes are fixed with screws.

Proper storage and use of the tool

Each pipe is fastened with a plywood plate with self-tapping screws through a slot. To prevent the pipe fragment from loosening during operation, pieces of glazing beads are glued under the sides of the holder with PVA glue.

When it is necessary to hang the holder on the garage wall, the handle is inserted into the holder tube. The handle stand fits snugly into the slot and is fixed. With this additional equipment, the coil is mounted on the ceiling or on the bottom of the shelves.

To make the extension bar easy to rotate, a small handle is mounted on the edge of the device disk, which consists of tubular segments of various diameters. The larger diameter pipe is slipped onto the smaller hose and fixed firmly with a flat screw.

DIY homemade products for the garage: the best ideas with photos

Useful homemade products for the garage with your own hands

Most often, during the initial arrangement, all the necessary furniture is ordered. But if you rent a room or do not want to take money out of the family budget for this, then you can easily settle down on your own, especially if you know how to hold basic tools in your hands. To help yourself and for inspiration, you can use the video from homemade products for the garage with your own hands (YouTube can please you with a variety of ideas), or you can take into account the tips for arrangement, which will be the basis for a successful layout.

If you look at a photo that demonstrates the optimal set of useful furniture elements, then note the useful nuances for yourself. First, the location of any storage system should be located at a certain distance from the walls. It is believed that there should be at least half a meter between the machine standing inside the room and the rack for normal, comfortable work inside. If the shape of the storage of your car is more like a rectangle than a square (this happens quite often), then it is worth moving the entire storage for tools and useful things into one zone along the far wall opposite the door. It is here that you can place with maximum convenience not only a table or a rack, but even a carpentry or lathe. It is not superfluous to mention that all the storage of your tools should be placed inside the garage only if it is securely closed or is protected by a tightly closed gate in the country. Otherwise, it is better to place there only the most necessary, preferably not of particular value to the robbers.

If you envisage installing windows with your own hands in a separate room, which is located on the territory of your suburban area, then it is better to make them of the so-called attic type, that is, located in the roof, and, moreover, choose a place just above such a working area. In the summer and spring, such an arrangement of windows will help you save on lighting, there will be enough sunlight for all types of work, besides, you can also ventilate the room, because ventilation cannot always cope normally, especially if you are going to study inside. like in a workshop.

With a total shortage of money or out of love for art, you can make an original storage system using old empty canisters. Every motorist accumulates a lot of them over the course of a year, and if you ask fellow neighbors, there will be enough for each compartment of such an interesting locker. Of course, there is nothing difficult here, and for performing such homemade garage do it yourself video-the lessons are not needed at all. You need to take a plastic canister, wash it well so that no traces of its contents remain. Armed with scissors for metal, a knife or other tool, we cut off the front cover from the canister, but so that the sides remain, and the contents do not overflow. To make the structure more stable, you can fix it on the back wall using self-tapping screws, but we will, of course, drive them not into the wall, but into a wooden rail, which we attach to dowels.

Homemade garage do-it-yourself photos

The same option, as shown in the photo, can be used in homemade products for a summer residence, because there, too, often you need to equip a workshop, and even less space is allocated for it than it remains in the garage. For such a design, you will need to build a frame of wooden planks, and make notches along its upper and lower edges, where the cells will be inserted. Most likely, the inspiration for this design was the classic hives that are used for breeding bees, the system is exactly the same. Sheets that are inserted inside have a perforated surface and the presence of these small holes will allow you to screw nails inside, hang hooks in order to hang tools and useful devices as conveniently as possible so that they do not fly off when sliding in and out.

The exact same perforation can be incorporated into a furniture set. With such a complete set of everything you need for a home craftsman, you can build many useful homemade products for the garage with your own hands, video with which there is on the network. In terms of popularity, such resources may soon overtake popular hand-made projects, because men, no less than women, want to make the space around them, their kingdom, beautiful, functional, and comfortable.

Interesting DIY homemade products for the garage

We are accustomed to either just throwing away the worn-out tires, or making crafts from tires for the garden with our own hands. Having examined the last winter set for a swan or a flowerpot, this year you can easily allocate it to yourself by making a whole furniture set. Frankly speaking, for this purpose, you will need not only car tires, but also bicycle tires, because they can be used to design backs by turning a stool into a chair.

Practice making such furniture and soon you will be able to replace your coffee table with such a table in the living room with your own hands, crafts from tires look not only beautiful, but can also become part of the original design concept.

A table and chairs are great, there will be where to sit, but with the question of what to cook a delicious shish kebab, our next idea will help here. The fact is that an ordinary folding brazier may not maintain the required temperature of the coals for a long time, and if you like to sit near the fire for a long time, you should make something larger. We will modernize crafts from a wheel for a garden and present to your attention a brazier made on the basis of a wheel rim. In order for the rim to maintain the set temperature well and not let the coals cool down, it must be covered with bricks, but for the maximum decorative effect of such a homemade product, it is better to file them a little with a grinder to fold them in a circle. The bottom must be covered with any available material that does not support combustion, for example, fine crushed stone.

Homemade garage do-it-yourself drawings

If you plan to spend a lot of time in your impromptu workshop, then among those you are interested in homemade do-it-yourself garage - heating, lighting, ventilation, that is, the arrangement of a full-fledged comfortable stay inside for a long time. Some people prefer to install infrared heaters, but from the point of view of the cost of electricity, this will not be a very rational option. Hot water heating can be a good option, but it is best designed in garages that are located next to a residential building.

You can place solid fuel boilers of any design inside a garage of any type, even make your own stove-stove made of metal using a welding machine. But do not forget that with this type of heating, the interior decoration must be made of non-combustible materials, and the ventilation is done with high quality, even at the stage when we build the roof with our own hands in order to timely remove all combustion products from the room.

DIY homemade machines for the garage

If you have a need for some specific work, then you can use special machines, for example, a pipe bending machine, which can be useful not only for motorists, but also for motorcycle owners.

DIY garage attachments - make a home workshop out of a caravan!

Required tools and materials

Any car enthusiast is able to make a variety of garage accessories with his own hands, using inexpensive materials and the simplest tool. Such homemade homemade craftsmen turn the motorhome into a full-fledged workshop.

Garage workbench - hard to do without it!

If you plan to self-service your vehicle in the garage, as well as perform a variety of repairs and make your own crafts, it will be difficult to do without a workbench. It is usually made from wooden planks, which are mounted on a reliable base (metal profiled pipe or thick wooden bar).

It is allowed to make a work table from metal blanks. They can be easily cut to the required dimensions and assembled into one solid structure by means of steel corners and hardware (universal screws, screw connections, bolts, and so on) or using a welding machine.

The manufacture of a wooden or metal workbench always begins with drawing up a detailed design drawing. You must correctly assess the working space of your garage and fit the desktop into it as harmoniously as possible. It is advisable to provide for the presence of shelves and drawers (pull-out) on the workbench. They allow you to keep all kinds of tools close at hand. It is recommended to install a small vice on the countertop.

Making a metal workbench

If your garage has shelves or racks (or you want to mount them), experts advise installing a workbench next to them.

Then you will get an excellent work area where you can do any homework, producing original and useful homemade products for your home.

Assemble a tabletop from boards with geometric parameters suitable for you (for example, 200 x 10 x 5 cm), connecting wooden products to each other with metal ties and good glue. For a standard workbench, suitable for any garage, 20 of these planks are sufficient.
On the tabletop, make special grooves (on 5 and 16 boards in a row) under the stops. The parameters of the grooves are 2.5 by 2.5 cm.
After the glue dries, the worktop must be planed so that a perfectly flat work surface is obtained.
From 80 x 10 x 10 cm bars you make legs for the workbench. Grooves should be provided in the front supports. You will insert the brackets into them, which you then connect to the beam (longitudinal).
Assemble the base of the underframe from two frames made of 10 x 5 cm boards and fix it to the support. The frames are cut into the legs of the workbench by about 2.5 cm, and then they are fastened with bolts.
Attach the supporting walls (back and side) to the resulting structure. They can be made from centimeter plywood or chipboard sheets.

Now you need to connect the top frame to the table top. This operation is carried out without any problems using the bolts. Do not forget to apply drying oil on the made wooden workbench and varnish it. On such a table, you will make any crafts with special pleasure!

Shelving is a must for a garage!

Over time, any vehicle owner turns into a kind of warehouse where a variety of items and tools are stored. All of them need to find a comfortable place so that each device is easy to find. A do-it-yourself rack allows you to efficiently organize the storage of tools.

You can make such a structure out of metal and wood. In the latter case, use a solid wood - beech or oak. Shelves and drawers from them are able to withstand quite serious loads. The rack, according to the accepted standards, is obliged to maintain a pressure of at least 150–160 kg. At the same time, it is not recommended to load home-made structures with things that generally weigh more than 500 kg.

Shelving made of wood

Let's see how you can quickly make a garage rack, spending a minimum of money on the purchase of materials. The work flow chart is as follows:

Take a 9 cm wide board and cut it into pieces of different sizes (18-30 cm). We will use these pieces as supports for the rack.
Make the shelves from a more powerful board - 19 cm thick. To do this, you will need to saw it into pieces of the desired length.
Mark the board for the base of the structure, indicating on it the points for the location of the spacers (they are usually removed from the edge of the base by 2.5-3 cm). Now you need to attach (preferably using construction glue) the top spacer and nail the top shelf of the rack to it (with ordinary nails of suitable sizes). Then repeat these manipulations with the other shelves and spacers. Lastly, the lower spreading element is attached.
Turn the assembled structure over, tighten the base of the rack with the spacers using screws.

The facility for storing various tools and things is almost ready. You just need to sand the rack and then apply oil varnish to the wood (it is better to make two layers), and then attach the homemade structure to the wall with anchor screws. The racking attachment points to the wall are under the lowest and highest shelf.

Useful technical homemade products for the garage - press and cyclone vacuum cleaner

A homemade clamping device, which is sometimes impossible to do without in home art, is done very simply. You will need:

hydraulic jack;
metal platform bed;
profile pipes with a cross section of 6x6 and 4x4 centimeters (each will require two pieces).

The press is done in this way:

Attach two vertical guides (4 x 4 cm pipes) to the base of the structure.
Weld between them (at the very top) a piece of pipe 6 by 6 cm.
Install another 6 by 6 cm pipe so that it can easily move along the mounted guides.

Homemade garage press

The use of such a technical homemade product is elementary - you put the products that you want to connect on the working surface of the press, cover them with a thick plywood sheet, lower the jumper pipe with the jack placed on it. You only need to pump pressure into the jack to glue two products or your own crafts for centuries.

But with the help of the next home-made product - a cyclonic vacuum cleaner, you can always put the perfect order in the garage. It is made from a dense plastic or (which is better) from a metal container. It must be sealed. The scheme for making homemade products for effective garbage collection in a motorhome is as follows:

Make two holes in the lid of the container. Place the first at the edge, the second in the central part. The diameters of the holes must match the cross-sections of the hoses that you will connect to the device. One hose is supplied to the hole from the edge, it is designed to collect debris, the other is needed to connect a conventional vacuum cleaner.
In the inlet pipe of the described homemade product, you need to install a plastic elbow. It will ensure the process of swirling (cyclonic) air in the tank. Due to this knee, the efficiency of such a homemade product increases, which will easily and quickly suck in small stones, lumps of dirt, sawdust and other solid contaminants. They will all collect in the tank that you connected to the vacuum cleaner.

Tool for making strong rope from plastic bottles

When heated, the material from which bottles for mineral water and various drinks are made is able to shrink. This gives us the opportunity to make an excellent rope out of such containers. With its help, you can very tightly connect a variety of parts and assemblies in a motorhome and in general in a household.

Rope from a plastic bottle

To make a device for making homemade cords, you need to stock up on two bolts with washers and nuts, metal washers, a piece of thin board or plywood, a stationery blade and an electric drill. We do the device like this:

Place two washers in the middle of the board or plywood, mark their centers.
Drill holes in the marked centers with a drill.
Drill holes from the back side (this is a mandatory procedure to ensure that there is no twist or rotation when using the device).
Screw in the bolts.

The use of such a craft is simple. It is necessary to put several washers on the protruding sections of the bolts (their number determines the thickness of the rope to be cut). Then a clerical knife should be placed on top of the washers (you can even use a piece of it) and strengthen the structure by installing a few more washers and tightening the nuts all the way. After that, the homemade device must be fixed with clamps on a garage workbench or other work surface.

Next, we take a plastic bottle with a volume of two liters, cut out the bottom of it, cut a strip (very small) of the required length and set our "blank" under the knife. Pull the tape with one hand, while holding the container to be cut with the other. From one bottle of 2 liters, you will get about 25 meters (linear) of excellent rope with high shrink characteristics.

Under the tool - useful homemade products for the garage with your own hands

I live in the city of Veliky Novgorod, our plant for the production of tanks, they produce drainage EP and EPP. For any city, this is a very useful thing. Since these drainage units are needed to drain oils, oil, fecal waste. On the site, I learned a lot of useful information, quality, dimensions, purpose of drainage tanks. The NOVZERO company provides us with various containers for water towers, air collectors. You can order everything in Veliky Novgorod, there are numbers for orders. Also, this company provides a guarantee, services, such as installation of equipment and more. Each city should have such factories and such products. novzero.com www.novzero.com/produktsiya/emkosti-ep-i-epp

No. 15 Homemade accessories for the garage

DIY garage accessories

DIY garage gadgets #tool

Homemade machines. DIY machines

Do-it-yourself things # 8 you can't do without in your garage

DIY hydraulic press

No. 15 Homemade accessories for the garage

Under the tool - useful homemade products for the garage with your own hands

DIY garage accessories

DIY accessories for home workshop and garage

Homemade Garage Accessories, ROLLING JACK

The article discusses the most convenient and practical accessories for a garage with your own hands, which can improve the comfort of using this room. Here are detailed recommendations for the development and creation of structures designed for convenient storage of tools and car parts, advice on the manufacture of furniture, as well as the arrangement of the lighting and heating system.

Useful DIY garage accessories: general recommendations

The garage is intended not only for storage, but also for car maintenance. For this reason, this room should be spacious, clean, comfortable and well equipped.

To achieve all this, it is enough to take into account the basic requirements for the organization of space:

The presence of shelves for tires and storage of tools significantly saves free space and allows you to optimize space.

The quality of lighting is of great importance, since not only productivity depends on it, but also the quality of minor repairs.

The construction of a garage workbench, machine tools, a viewing hole and other fixtures expands the range of possibilities for a car owner in relation to vehicle repair and maintenance.

Optimal organization of the storage system in the garage: 1 - open brackets and hooks for frequently used tools, 2 - a rack for small tools, 3 - shelves for spare parts and tires, 4 - a rack for large tools, 5 - cabinets for various things, 6 - workbench with additional shelves

About 80% of the shelves in the garage are self-constructed for storing garage accessories, namely:

tools and accessories;
component parts for the car;
accessories.

Often, in the photo of shelves in the garage with your own hands, you find their combination with a rack, which can also be made independently. More often than not, the rack is considered as the main place for storing tools. After installing it, the remaining space is filled with comfortable and spacious shelves.

Be sure to provide a place to store your work clothes. It is not necessary to occupy a large area, you can get by with one shelf or even a crochet (depending on your needs).

A garage is a place where hazardous and flammable substances are stored. These include oil, gasoline, solvents, paints, polishes. For them, it is necessary to provide a separate cabinet, hang a fire extinguisher and install a tank with sand.

To protect against contamination during storage of wheels mounted on tire brackets, it is worth purchasing large bags or specialized covers to prevent dust from entering.

Brackets and shelves for wheels in the garage: design features

The most bulky spare parts of a vehicle include sets of rubber, which can be winter or summer. When a winter version is used, summer tires are usually stored in the garage and vice versa. Therefore, you should arrange shelves for storing tires or brackets.

The bracket design is as follows:

Two triangular frames made on the basis of corners. Jumpers made of any durable metal are installed between these frames.

The triangular parts of the structure are fixed to the wall at a pre-selected location. The wheels should be installed perpendicular to the support structure. In this case, the tires should fall slightly between the jumpers, thus fixing themselves on the shelf due to their own weight.

For compact storage of wheels, a whole rack in the form of four wide shelves can be used. It is suitable for placing wheels with disks that can be positioned one above the other in a horizontal position. The structure can be made angular and raised on the wall.

wooden beam;
boards;
chipboard sheets.

Installing tire brackets is the most efficient way to store your wheels. More space savings can be achieved by hanging the rubber from the ceiling base along the garage wall. This option is possible if the room has a high height and reinforced concrete slabs on the ceiling. They will be used as a base for screwing in dowels.

Tool storage: interesting ideas for a garage with your own hands

To organize a convenient area for storing things, you can independently make a homemade and very spacious rack or shelves. Of course, in stores you can find hundreds of ready-made models, nevertheless, making a shelf in the garage with your own hands is much cheaper than buying a similar product on the market.

The problem is the same for shelving. Taking up the independent manufacture of storage space for tools, you can not only organize a convenient and practical rack, but also harmoniously fit it into the garage space.

Rules for the manufacture of wood products:

It is better to use hardwood such as beech, oak, hornbeam.

Before assembly, wood must be treated with antiseptic agents.

Frame parts must be carefully sanded to ensure safe operation of the rack.

For the manufacture of shelves, it is recommended to use chipboard or plywood sheets, OSB. DVL plates with a thickness of at least 4 mm are also suitable.

The thickness of the material is determined by the loads that will subsequently act on the rack.

Recommendations for making do-it-yourself tool shelves in the garage

Shelves are installed in cases where the garage does not allow to put a rack. It is better if there are several structures.

Scheme for creating shelves for tools:

Plan the placement of shelves, determine their size and carry out the markings.

Prepare the material in the form of boards and fasteners.

Using a puncher, make holes in the wall, install dowels with hooks in them, which will provide enhanced fixation.

Fasten hangers equipped with lugs on the boards. For metal hangers, it is recommended to use self-tapping screws or regular nails.

Fix the finished products using the building level, otherwise the tool may fall from the shelves, which makes operation unsafe.

At the final stage, you can make a decorative finish of the products (paint or special film).

Garage tool rack technology

To create a rack with your own hands, you will need boards 9 and 19 cm wide. The size of the structure can be adjusted.

Step by step technology:

A 9 cm wide element is cut into several pieces 18 cm, 27.5 cm and 30 cm long. The resulting parts will be spacers.

The board, which is 19 cm wide, should be cut into 36 cm long pieces. Shelves will be made from these parts.

On the board, which will become the base of the product, it is necessary to apply markings in those places where the spacers will be. It is recommended to indent each side by 2.5 cm.

The upper spacer is glued, then the upper shelf, which already has a spacer, is nailed to it. The rest of the parts are mounted in the same way. The bottom brace is installed at the end.

The structure should be turned over and the spacers should be tightened with screws along with the base of the product.

The surface is carefully cleaned with sandpaper. After that, the product must be covered with two layers of oily varnish or another type of finish.

The structure is fixed to the wall with anchor screws. Fixation should be done both under the upper and lower shelves.

Organization of the lighting and heating system in the garage

In order for the operation of the garage to be comfortable, the lighting, ventilation and heating system should be properly organized in the room. Since cars are closely associated with the use of toxic and harmful substances, the problem of ventilation in a confined space is especially acute. For a garage, air vents are suitable for brickwork. They are equipped with grilles.

Factors affecting the level of lighting:

garage area, its height;
the number and nature of the placement of working areas (dimensions of a workbench for a garage, inspection pit, number of machines);
type of decoration on the walls, its colors;
indicator of the specific power of the network per 1 m2;
type of lamps for the garage.

Various types of heating can be used to maintain the optimum temperature:

gas;
based on used oil;
air;
electric (infrared heater for the garage);
oven;
water;
solid fuel.

There are many alternative ways to organize your own heating system.

Features of halogen, fluorescent and LED garage lights

The technical characteristics of halogen lamps are in many ways similar to incandescent lamps, but their bulb is filled with bromine vapor, so the products emit more light. The advantages of such lamps include a long service life - 4 thousand hours.

Fluorescent lamps are filled with inert gases inside. From the inside, the flasks are covered with a specialized compound that emits ultraviolet light under the influence of an arc-type discharge. Recommended models are IP-65 rated products that are protected from moisture and dust particles.

Installing LED lighting in your garage comes with the highest cost. Nevertheless, they pay off in 50 thousand working hours. In terms of efficiency, LEDs are 50% more profitable than fluorescent lamps. At the same time, they do not contain harmful components, and the light does not have an aggressive effect on the eyes, therefore, it is not necessary to purchase plafonds.

Installing lighting in the garage: how to make a calculation

To calculate the power of conventional lamps, you can use the formula:

P = S x W / N.

Decoding of values:

P is the total required power, W / m2.
W is the power of one lamp, W.
N is the number of lamps (luminaires), pcs.
S is the area of the room, m2.

For halogen and LED luminaires, the optimal indicator is 16-20 W / m2. This value is suitable for rooms where the ceiling height is no more than 2.5 m. In garages with 3-meter ceilings, this figure should be multiplied by 1.5.

The calculation is influenced by the interior decoration of the walls of the room. In dark garages, the lighting should be brighter.

Light reflection level:

To illuminate the inspection pit in the garage, it is recommended to use low-power lamps with halogen or LED lamps, since moisture accumulating in this place can provoke an electric shock. The devices are mounted on the sides in pre-made recesses.

Do-it-yourself autonomous lighting system in the garage

There are a number of principles on the basis of which an autonomous lighting system is performed:

LED strips are mounted inside the shades (there are 300 diodes per element).

The output of the switch is carried out strictly on the shield.

A suspended ceiling system is used for wiring.

The wires are powered by a battery connected to the mains via a charger.

A multi-level garage lighting system is considered the most optimal. It involves the installation of a large lamp in the middle of the room and the installation of small lamps in the working areas.

Calculation of height for a multilevel system:

The luminaires are installed correctly if the machine does not cast a shadow on either side.

How to choose a heater for a garage

Garage heating is carried out using small portable devices that are able to warm up the room in a short time and further maintain the optimum temperature.

Thinking about which heaters are best for a garage, many people mistakenly believe that a home-made device can be made exclusively from expensive components and takes a significant amount of time. For this reason, garage owners abandon this venture.

In fact, for making a garage heater with your own hands, it is enough to limit yourself to budget materials, for example, thermal film. The scheme for creating such a device is very simple and involves the use of the following materials and tools:

a kit for assembling a heater;
wires complete with a plug;
paper laminated plastic (the area of one element is 1 m2);
graphite powder;
epoxy adhesive.

Recommendations for assembling a homemade garage heater

Step-by-step instructions on how to make a garage heater:

A mixture of glue and graphite powder is made. The more powder in the composition, the stronger the heating of the device will be. The average temperature ranges from 60-65 ° C.

The plastic sheets are coated on the rough side with a mixture of glue and graphite, which is applied in zigzag strokes, after which they are fastened with the front sides and fixed with a frame made on the basis of wooden slats.

The terminals are fixed to the graphite conductors and the structure is dried. Drying must be complete, otherwise moisture will ruin the device.

After the heater has dried, a resistance test should be performed. A garage heater is only considered safe after this check. Until this moment, it is strictly forbidden to connect the device to the electrical network.

Security restrictions:

It is not recommended to leave the switched on device unattended or leave it near children.

It is forbidden to use equipment capable of provoking a fire.

Flammable substances and materials must not be placed near the device.

DIY useful garage fixtures

To carry out repair and service work, you will need to build an inspection hole in the garage with your own hands, the dimensions of which will correspond to the dimensions of the car, as well as a workbench for convenient work, plus equip the room with machines.

A basic set of tools and materials for creating a homemade garage workbench includes:

boards and wooden blocks;
fasteners and ties;
planer and other tools for woodworking;
varnishing and joinery adhesives;
sandpaper and drying oil.

An example of placing useful devices in the garage: 1 - a workbench with hand-held machines, 2 - racks and cabinets, 3 - a table for various repairs, 4 - a shelf for storing tires, 5 - an inspection pit

DIY workbench manufacturing technology in the garage: photos, drawings

The workbench consists of a table top and a base, as well as several clamping devices. The height of the workbench in the garage should be adjusted to suit your own height. You can take as a guide the height of the kitchen table in the house, at which it is convenient to work. Be sure to draw up drawings for creating a garage workbench with your own hands.

Arrangement of a garage: how to make a workbench indoors:

Final processing involves impregnation of the finished product with linseed oil and opening with varnish.

Recommendations for creating a viewing hole in the garage with your own hands

There is no specific size for a garage inspection pit. The dimensions of the car are taken as a basis.

How to make an inspection hole in a garage with optimal parameters:

The width is selected so that there is enough space inside for work. The size is limited by the distance at which the wheels of the car are planted. Each wheel needs a small area to maneuver. The average pit width is 0.8 m.

The length of the pit is limited by the length of the machine. To this indicator, 1 m should be added.

The height of the garage owner is used to calculate the depth. Another 10-15 cm is added to it.

How to properly make an inspection hole in the garage using different materials:

The pit is pulled out taking into account the optimal width of the pit, the material chosen for the walls, as well as the thickness of the waterproofing layer. Stages of creating a pit:

markup;
pit construction;
arrangement of the pit;
construction of walls;
lighting strip.

For waterproofing walls, a specialized hydrophobic impregnation is used.

Scheme of arrangement of the inspection pit: 1 - walls made of foam blocks, 2 - waterproofing, 3 - rubble masonry. 4 - corner 50x50x4 mm

DIY garage press

To create a press, a frame with a size of 178x80 cm should be made from 4 pieces of metal pipes. These elements are connected by welding. In the work, it is recommended to be guided by drawings, pre-selected or drawn up. After that you need to install:

retainer;
removable emphasis;
bottle jack (hydraulic).

You can use video materials to consider the detailed technology for creating useful accessories for the garage with your own hands. Such visual recommendations help you navigate in size, master step-by-step instructions and imagine what kind of appearance the finished structure should have.

Hydraulic press manufacturing scheme: 1 - upper power platform, 2 - nuts, 3 - lower platform, 4 - studs with a diameter of 30 mm, 5 - lower thread of studs, 6 - bottle-type hydraulic jack; 7 - base 20 mm thick

Arrangement of the garage can be done with your own hands. The list of useful tools does not end there. It can always be supplemented with any interesting ideas. The main thing is that the garage fully meets the personal requirements in terms of comfort and convenience.

With proper arrangement of the space, the garage can serve not only for parking a car, but also be a workshop for its maintenance. In addition, a properly planned space can easily accommodate the required tool, provide storage of technical fluids and wheels in the off-season. The functionality of the premises will allow you to expand, which can be made from improvised material or purchased in specialized stores with subsequent refinement to fit your needs.

Considering the fact that the number of things in the garage will increase over time, it is worthwhile to rationally use the walls, floor, basement (if any) by equipping them with the maximum number of shelves, hooks, racks. For skilled people, they define a workplace, equip it in accordance with the needs.

Storage of bulky items

All items that occupy the garage space are conventionally divided according to several characteristics: large and small, required constantly or used once or twice a year. Depending on this, before starting the arrangement of the space, they work out a list of large things of not frequent use, which include:

winter, summer wheels;
bicycles;
skis.

The list may be longer, perhaps the garage owner loves locksmithing, then in his arsenal there will necessarily be long pipes (plastic and metal) of different sections, bars and boards. For compact, ordered storage of large-sized things, garage home-made or purchased devices are used, for example:

Purchase wall mounts for bicycles that allow them to be stored in an upright position, which provides significant space savings;
For rubber sets, special shelves are equipped, on which each wheel lies separately. They are placed in any convenient place, for example, under the ceiling, along the wall or, capturing the corner space, or suspended from the ceiling or wall on an appropriate support, having previously cleared of dirt, packed in special cases. This way of storing tires is only suitable for kits on disks.
Considering the cases when tires without disks are stored, a rack is welded from metal, on which the tires stand vertically in one row. Place the device under the ceiling or on the floor, securely fixing it;
With the help of homemade mounts, they provide a compact arrangement of skis, ski poles and other sports equipment.

Attention! Provision should be made in advance for space in the upper third of the wall for storing the removable trunk.

In addition, craftsmen make various suspended ceiling structures parallel to the floor to accommodate long objects such as pipe pieces or beams.

Accessories for small things

For many craftsmen, the number of different-sized screws, nuts, bolts, washers is measured by a bunch of boxes and buckets, in which it is extremely difficult to find the right part. To resolve the issue, such adaptations for the garage have been invented, which allow you to streamline small things and ensure that the desired part is quickly found, for example:

special portable boxes with compartments. A convenient option that allows you not only to store, but also to transfer the required parts if necessary. It should be noted that the cost of the boxes is relatively high, therefore, the ideas proposed below will help reduce costs;
craftsmen sort small nuts and other parts into jars with screw lids, while the lids themselves are securely attached to the hanging shelves. It remains only to screw the jar into the lid and the details will always be in sight, at hand.

If financial resources are available, they acquire compact storage systems for hardware, nuts and other parts, different in size, and differing in mounting options.

Tool storage

The working tool is divided into large and small, respectively, homemade accessories for the garage will be different. In most cases, owners prefer to store a cutting machine, a perforator, and other large tools using their "native" boxes. Therefore, for their convenient location along the wall, a rack is made from scrap materials, taking into account the total load on the shelves (for self-made structures, the weight should not exceed 150 kg).

Attention! The stores offer a wide variety of models of shelving, made of both wood and metal, withstand loads of up to 500 kg or more. At a relatively low cost, it is convenient to purchase a ready-made rack in the garage for the desired size, fixing it against the wall.

For small tools such as wrenches, screwdrivers, pliers and others, organize the space according to their number:

sets are stored in purchased boxes, placed on a rack;
for single items, either they equip cabinets in which each tool is fixed in a corresponding niche, or they prepare a perforated surface (like in a store) fixed on the wall and determine a specific place for each of the tools.

Some craftsmen place their tools using structures made of plastic pipes, in which holes of the appropriate diameter are made.

Homemade machines for garage work

For comfortable repair work, a place for a workbench is provided (to save space, it can be folded). To begin with, they work out the drawing of the table, thinking over the presence of retractable shelves, then they make it from boards or metal sheets, equip it with a vice and a sharpening machine.

In some cases, craftsmen cannot do without home-made machines and other devices made on their own and improving the quality of the thing made.

Press from improvised tools

One of the most popular DIY garage gadgets,. To create it, you will need a hydraulic jack, a metal surface that will serve as the base of the moving part of the press, springs and profile pipes or a channel to create a frame. Further:

create a frame by welding channels and reinforcing the structure with transverse stiffeners; downwardly for stability, transverse corners are also welded;
the movable platform is attached to the upper frame with springs, a jack is installed.

The efforts of the press are regulated by a jack.

Depending on the needs of the garage owner, other useful home-made machines are made, for example, a drilling machine made on the basis of a drill, fixed with clamps and moving along a rail using a gear or a cut-off, or a lathe.

In addition to the devices listed above, you should take care of the location of work clothes, provide for a fire extinguisher or sand (based on fire safety rules), think over ventilation and lighting systems.

Thus, with a little ingenuity and thriftiness, you can make accessories for the garage with your own hands, thereby ensuring compact storage of things and freeing up enough space for minor car repairs and work related to servicing one or another home appliance.

From time immemorial, a storage room for a car was considered not only a place to relax after a hard day, but also a unique workshop. Men equipped it, creating various homemade products for the garage with their own hands. On the territory of a small space, you need to arrange a huge number of things for convenient use and safe storage. Enterprising craftsmen do not lag behind their ancestors, but continue their work, using modern methods and technologies. Consider the popular ideas of original designs for the work area of real men.

When arranging a room for parking a car, it is necessary to observe the basic safety rule. An entrance gate or door must be easy to open and the passage to it must always be free.

Garage DIYs - A Wise Approach to Space Retrofitting

Almost every car enthusiast will be able to equip a "house" for an iron horse with his own hands. The main thing is to tune in to the fact that this is an ongoing and long-term process. It doesn't hurt to connect creativity, skill, and firm determination to achieve your goal. Practical advice from experts will help you create original homemade products for the garage, for those who are ready to get down to business. In addition, it brings tremendous satisfaction when ordinary objects turn into a necessary and valuable thing.

Car tire storage

Experienced drivers change the “shoes” of their car every season. Where is the best place to store tires so that they do not lose their properties? A simple DIY homemade garage solution will forever solve this sore point.

For the correct storage of tires, the type of wheel design plays a key role: with or without a disc.

Car tires mounted on disks are stored suspended or in stacks. For the first option, simple materials are used:

metal cables;
chains;
luggage belts.

Often they are fixed to the ceiling, load-bearing wall, or to a beam located in the upper part of the room. An original craft for a garage with your own hands is hammering metal hooks or pins into the wall. They are stuffed over the entire area of the wall, the main thing is that the wheels do not touch each other.

Metal pins should not protrude beyond the edges of suspended structures.

Car tires without rims are stored "standing". Suitable shelves are made for them, welding profiled pipes with a diameter of 30 mm or a corner. The width of the structure is 4 times the width of the wheel, plus 15 cm for free placement on the shelf. The height of the rear of the structure is 10 cm higher than the outer volume of the tire. Such a do-it-yourself garage device is hung on the wall.

The storage area for tires must be protected from sunlight to prevent the rubber from deteriorating.

A good owner has everything at hand

To equip a working area in a garage, experienced drivers first determine where to place it. If the room has a rectangular shape, then it is convenient to build a "corner for creativity" along the entire width of the back wall.

Such a useful hand-made device for the garage will help solve three main problems:

compact arrangement of a large number of things;
ease of use;
free movement in the room.

For a wide garage, it is better to place the structure along one of the side walls or as a corner option. In this matter, the garage owner independently makes a decision based on the size of the room.

A great idea for a garage is to DIY a wooden table or workbench. The construction will require:

profiled pipe or metal corner;
boards;
moisture resistant plywood or chipboard;
fasteners;
set of tools.

With the help of welding equipment, the frame of the future table is made, which is sheathed with plywood or chipboard. Alternatively, the structure can be made entirely of wood. In order to compactly fill the space, shelves are installed under the tabletop, where plastic or wooden containers are placed.

In addition, the craftsmen use various tricks in the garage - they build a rack from plastic canisters with their own hands. The same containers will do with the handle at the top. One of the sides is cut out, turning the canister into an original box for the motorist's valuables. Then the containers are placed on a wooden or metal rack, as shown in the photo. These garage storage systems have served motorists for many years. Since plastic is not afraid of dampness, temperature changes and is resistant to mechanical damage. As a result, the wise master has all the details at hand, which means he works without distractions.

Folding table for small spaces

A simple structure that can be made from an old cabinet will help to equip a work area in a small garage. The construction will require:

chipboard sheets;
corners;
several loops;
mortise nuts for furniture;
wooden block;
self-tapping screws;
anchor bolts.

First, mark up the future structure using a level. Through holes are drilled on a wooden block and attached to the wall using anchor bolts. Then the prepared table surface is connected to it with the help of moving curtains. The design fits wonderfully into a small room and is used only when needed.

Ideal place for tools

Each driver has an arsenal of tools available. Some of them are used quite often, others - once a year. Original homemade garage fixtures are a simple solution to the problem. They contribute to the perfect order in the room, as well as decorate its interior.

Organized people who put everything in their place can use the closed boxes for tools and car parts.

One of the devices is performed in a simple way. A metal reinforcing mesh (cage size 10 cm), which is made of wire (diameter 2 mm), is attached to the wall. Some parts of the cage are bitten off, then folded back and made into hooks or crossbars.

Motorists hang on them:

hand saw for metal;
a watering can for fuel;
various rubber hoses;
small car spare parts.

Another way of completing valuable tools for car enthusiasts is a screwdriver rack. For this, the board (approximately 15 cm thick) is carefully sanded, bringing the surface to a smooth state. Next, holes of different sizes are drilled (one or two rows). Each of them is cleaned to exclude the appearance of splinters. Attach the structure to the wall using brackets, after which screwdrivers or chisels are inserted into the holes. A similar device is made for storing hand tools. A board is nailed to a vertical surface. One of its sides is pre-cut down so that it is convenient to hang pliers, various types of nippers and pliers.

A special shelf is built to place the battery equipment in the garage. Its upper part has a flat base. At the bottom, projections of various formats are cut, where suitable parts of cordless tools are placed. This approach allows the car enthusiast to quickly find the right things, especially in critical situations.

Portable lighting systems

As you know, there are no windows in the garage. During daylight hours, light enters in only through a door or gate. When repairing the underside of a car, it is very difficult to do without. Experienced motorists are advised to make a portable lamp.

Creating the simplest design, they take an ordinary cartridge and connect it to an electrical wire, at the end of which a plug is attached. For lighting, a conventional incandescent lamp or "housekeeper" is suitable. The main thing is to fit under the cartridge.

To protect fragile glass, you can make a lampshade out of it. A milky vessel of medium thickness is suitable, which perfectly diffuses light. The design is used to illuminate the most secret parts of the car and distant parts of the room.

Compact electric drill stand

When performing various works in the garage, they are often used. The tool needs to be treated with care, so keep it in a safe place. In addition, it is easier to drill holes on a flat and stable surface without distortions. The original stand for an electric drill is easy to make, if you heed the advice of experts.

To begin with, collect the main components of the structure:

flat area of the old milling machine;
calibrated tube or rod;
plywood sheet.

A box is made of thick plywood, which corresponds to the size of an electric drill. Two holes are made in it with a drill. Next, the drill is attached to the box using special nuts. The structure is installed on the rack towards the base. A handle is fixed at the top of the rack, next to the bar. A standard ruler is installed along the base, which serves as a limiter for the unit. In this position, it is much more convenient to work with a drill. The holes are smooth and without visible deviations.

The do-it-yourself useful things for the garage shown in the photo vividly testify to the skill of modern motorists. The main purpose of arranging a car house is the rational distribution of the working area and the convenient placement of valuable things. Thanks to this, it will be comfortable to work in the garage, relax and even chat with friends.

DIY garage lathe - video

You just need it - video

By on home garden Many car owners use their garage as a workshop, gradually filling it with practical devices that make it easier to repair and maintain a car. Many of them can be made by yourself using the recommendations presented in this article.

Many garage workshop accessories can be ...

Homemade Garage Tools: For storing tools in the garage. Homemade tools for the home workshop

By on house garden

Many car owners use their garage as a workshop, gradually filling it with practical tools that make it easier to repair and maintain a car. Many of them can be made by yourself using the recommendations presented in this article.

Video homemade machines and accessories for the home workshop

Many accessories for a garage workshop can be made independently, the video below demonstrates some of them.

Garage homemade products are devices that greatly facilitate the garage life, in addition, they work no worse than factory machines. Having equipped your workshop with such devices, you can independently make the necessary parts for a car, as well as various crafts for your home or summer cottage.

Video homemade tools and accessories for the garage

It is difficult to predict in advance what devices may be needed when repairing a car, however, there are some homemade products, some are used most often. Some of them can be seen in the video below.

DIY drawings

Profile pipe bender

A pipe bender is a useful household device that allows you to bend a metal or polymer pipe at a certain degree. Bent pipes are often used in arranging greenhouses and greenhouses, installing heating and other needs. Using the presented drawing, you can make a manual pipe bender yourself.

Small homemade vise

A vise is a practical tool used when performing plumbing work. With its help, it is possible to reliably fix the part requiring locksmithing in a certain position.

This device consists of several parts:

base plate;
2nd lips - mobile and non-mobile;
lever;
undercarriage screw.

With the help of a small-sized locksmith vice, the drawing of which is presented above, it is convenient to sharpen and other processing of small parts.

CNC milling machine for wood

The presence in the home workshop of a CNC milling machine allows you to perform a number of works on the mechanical processing of wood.

A homemade milling machine consists of several units and parts:

bed;
calipers designed to move cutters;
caliper guides;
spindle with installed cutter;
a microcontroller or a switching board with microcircuits that automate the operation of the machine;
electric motor with power supply;
drivers responsible for transmitting commands from the controller to the electric motor;
a vacuum cleaner for collecting the sawdust generated by the machine.

A do-it-yourself CNC milling machine allows you to perform engraving and milling work.

Homemade car repair gadgets

The wiper arm remover is a special tool that facilitates the process of removing the wiper arms. You can make it yourself from a piece of reinforcement, a six-channel channel and a dozen bolts. To do this, use a drilling machine to make holes for 14 and weld 2 nuts on both sides of the hole and the handle from the armature, screw the bolt into the workpiece and, wearing heat shrinkage, screw in the threaded rivet. The tool is ready.

Another version of the device for shooting the windshield wiper rods is shown in the photo below.

Another useful home-made device with which you can manually re-flange the wheels yourself. Another version of this device can be seen in the photo below.

When carrying out serious repairs to a car, as a rule, you cannot do without a lift. A factory-made device is expensive and not required very often, so it can easily be replaced with a home-made device.

Homemade machines and accessories for the garage

Having made devices for tire fitting and balancing, you can independently perform these works, significantly saving money on car maintenance. In addition, such devices will come to the rescue if there is no way to come to a specialized tire service.

In your garage workshop, you can equip a universal tire fitting machine using available materials - metal pipes and a hub.

When doing various crafts for the home, it is often necessary to drill an even hole. This is difficult to accomplish with an ordinary drill, but if you make a stand for a drill, such as the one shown in the photo, then drilling without distortions will be much easier. Such a design can be made from various materials. For example:

made of metal;

made of wood.

Using the diagram below, you can independently make a drilling machine from a drill.

Using a homemade press will allow you to make products by pressing in a garage workshop. Such a device can be made from a hydraulic jack fixed at the top of the bed, which in turn is welded from scrap materials. The pressure is then directed downward.

Another version of a homemade press, the design of which involves mounting a jack at the base of the bed. In this case, the pressure process is produced upward.

With the help of a homemade press, you can straighten, bend metal sheets, press cardboard, and fasten individual elements. The video below demonstrates how to make such a necessary device yourself.

Garage tool storage

The presence of order is the key to the comfortable use of workplaces in the garage. To ensure this order in the workplace, special organizers are called upon, which make it convenient to store and easily find the necessary tools. You can make such devices yourself, using the means at hand.

An easy and affordable way to store your hand tools is a wall organizer made from cans attached to a plywood sheet. In addition, several hooks or nails can be nailed to it to conveniently hang the measuring and power tools. In the absence of tin cans, PVC pipes of various diameters, cut into pieces and screwed to a sheet of plywood or chipboard, can be used as holders.

It is even easier to make a special device for storing screwdrivers. To do this, you need to take a wooden block and drill holes of the desired size in it. Mount the finished holder on the wall. On the same holder, you can organize a storage system for chisels and a chisel. It is enough to cut out special holes in a wooden blank. In the same way, you can make a holder for power tools by sawing the corresponding holes in the wooden shelf.

An interesting way to store tools is suggested in the photo above. Its principle is based on the use of magnetic tapes attached to metal strips. With this system, it is convenient to store drills, keys and other metal tools.

Convenient and practical organizers for storing screws, bolts, nails and other small things can be made with your own hands from transparent plastic jars with lids. To prevent them from taking up space, you should attach them to the bottom of the lid to the shelf. This and other ways of storing tools allow you to efficiently use the space in the garage and everything you need at hand.

The video below demonstrates how to equip yourself in a workshop or garage with a simple and convenient tool storage system.

Homemade woodworking tools for the home workshop

Homemade milling machine

Homemade milling machines can perform one or more operations. Preference is, of course, given to multifunctional fixtures that save space in the garage. With their help you can:

Make indentations of a certain shape;

Drill holes

Make grooves;

Process blanks.

The simplest milling machine can be made on the basis of a drill. To do this, it is fixed on a steel profile or in a plywood case, and a rotating clamp is placed opposite it. Parts are processed using special hand-held cutters.

Homemade lathe

Making a lathe with your own hands allows you to make dishes, interior decor and furniture from wooden blanks. Such a device will become an affordable alternative to industrial models, and will help to realize your creative potential. A homemade lathe can be made from individual units and parts:

an electric motor used as an electric drive of the machine;
headstock, which can be an electric grinder;
a tailstock made from a drill;
an emphasis for incisors;
transverse guides;
a bed made of metal profiles or beams.

The headstock and tailstock of a lathe are the main working elements between which a piece of wood is placed. The rotating movement from the electric motor is transmitted to the workpiece through the headstock, while the back one remains static, being responsible for holding the workpiece. If you equip a homemade lathe with additional devices - a baluster, a trident, a copier and others, then its functionality will increase significantly.

The video below demonstrates how to make a lathe with your own hands.

Homemade drilling machine

If you need to drill precise holes in metal, plastic or wood parts, experienced craftsmen recommend using a drilling machine. Unlike a drill, which vibrates strongly during operation, such a device provides a high-quality result, regardless of the material and thickness of the workpiece. You can make a simple drilling machine yourself using the same home drill, but installing it in an upright position on a furniture board bed and attaching it to a metal rack. If necessary, such a machine can be equipped with an asynchronous motor.

As a rule, home craftsmen do not stop at making the machines themselves. Very often they work to improve existing equipment.

The video below demonstrates useful tools for a lathe that expand its functionality.

Homemade metal fixtures for the home workshop

These hand-made devices for the home workshop are designed to facilitate the metalworking process. They are usually made from scrap materials and tools.

Among the most demanded devices, it should be highlighted:

pipe benders;
press;
vice;
milling, locksmith, turning, drilling and thicknessing machines;
accessories for sharpening drills, knives and other tools.

With their help, a home craftsman can make practical accessories for a summer residence, a garage, and also equip a comfortable home. Examples of machines and devices useful in the household can be seen in the photo below.

Homemade circular machine

Homemade thickness planer

Homemade metal cutting machine

How to make some useful household appliances is shown in the video.

Taking into account the presented recommendations and drawings, any home craftsman will be able to make useful accessories for the garage and machines for his workshop, arrange an ergonomic space in it, and realize his creative abilities.

DIY garage accessories: all the most useful

Tags: Garage, DIY

We will send the material to you by e-mail

D For the rational use of space, communications and devices for the garage are used with their own hands from scrap materials. It is necessary to use walls, an underground level in the process, place machines inside the room, organize normal lighting.