Bench transformer drawings. Bench-transformer: not only comfortable, but also beautiful. The most successful model of the transformer bench

Such garden furniture is a bright example of a successful combination of beauty and practicality. Isn't it especially appreciated in a private house or in the country where it often lacks free space?

In the folded state, the construction occupies very little space (photo 1). And one hand movement The usual bench turns into a table with two shops - great for meals in the open air or for desktop games with children (photo 2). Building material: timing segment 90 × 45 mm, 90 × 32 mm, 45 × 32 mm. Preferred solid wood: beech, ash, oak, birch (in extreme cases of pine without bright shoes).

Instruments:
■ Desktop tracing machine - its lumbell with graduation will make it possible to obtain accurate parts of the parts (or you have to make a marking of the transporter and cut with a shallow tooth);
■ Extension and drills: spiral th 5.1 mm, D 3.0 mm (screw holes), 8.0 mm (holes for the seeds), feathers D22 mm (holes in movable parts relative to each other);
■ Zenker (deepening under the head of screws);
■ screwdriver with cruciform slot;
■ milling machine or handbank (removal of the champs on the bars forming the plane of benches and tables);
■ sandmashinka or sandlet with sandpaper (detail surface finishing),
■ Raspil (rounding angles).

Auxiliary materials: PVA carbonate glue, paint (impregnation), grinding paper No. 60, 80; Self-tapping screw; Wooden wet - 12 pcs. (Social. Details D-D1, FG1); Bolts M8X60 mm with self-locking nut and washers - 4 pcs. (Connecting parts A-K, Dr.).

Manufacture

At children. P and with chamfer, i.e. We twisted both ribs with a wide side of the bar. At children. P, forming the tabletop plane, take off one chamfer in two bars, which, when installing, will be extreme on both sides of the table top. In children. And and by the marking of the centers, first drill through holes with a spiral drill D5 mm. Then, conventionally seized children. The legs and the support bar of l table tops, from the outer sides, we set the recession under the head of the bolt with the feather drill. After that, the Drill D10 mm is drilled by centering holes. We do the same with children. D and E. in children. To drill through hole.

Details of the bench-transformer
Positions not specified in Fig.:
P- bars for countertops - 90x32x1480.5 pcs.;
R- bars for outdoor bench (in folded position) 90x45x1380 mm, 2 pcs.;
FROM- Bruks for inner bench- 90x45x1445 mm, 2 pcs.

In a country house or in the country, it is very convenient to use the transformer shop.

First, the design does not occupy a large area. Secondly, it can move at a convenient place for you. Thirdly, by simple movements, the shop is modified in a table with two benches, which is very convenient for carrying out a feast outdoors. How to make such a transformer shop with your own hands?
In order for the transformer, you need to prepare the tools:

bulgarian or tree hacksaw;

screwdriver or screwdriver set;

electrode or manual drill;

measuring devices (square, line, level).

Consumables include wood, self-tapping screws, sandpaper.
Technology of work

The manufactured shop consists of 2 benches and the backrest of the table top. Benches differ from each other width. We manufacture with your own hands the first bench with dimensions of 118 x 25 cm. To do this, using consumables, prepare parts in the form of 20 mm thick boards with dimensions of 118x12 cm. For the legs, cut 2 parts with dimensions:
37x11 cm - 2 pieces;

34x11 cm - 2 pieces.

All parts are well grinding using a special circle for the grinder, or with the help of sandpaper. The blanks of the legs of different sizes are combined by pairs using metal plates. The compound is carried out so that the height of the base is 45 cm, and the width is 37 cm.

2 parts 118x12 cm using self-screws screw to the bases, get the seat. Because of the low thickness of the boards, it is recommended before twisting the screws with a smaller diameter to drill holes in the connecting places so that the board does not burst. After assembling the first shop, we carry out measurements. When measuring, the outer width should be 118 cm, and internal 114 cm.
We collect a second bench with a width of 109 x 22 cm. The seat bench will consist of 2 billets 109x11 cm. In order to make the legs, the ram 40x40 mm will be required. The legs are made of blanks with dimensions:

32 cm - 4 bar;

22 cm - 2 bar.

Also from the boards drink 2 blanks 40x9 cm.

The bench-transformer saves a place on the plot and can be both a table and bench.

We make the legs of the second shop with our own hands, for this, to the bar 22 cm, using a wooden wanned, glue and self-tapping screws, fastened on a rib from one edge board. We carry out the same operation with a second bar length 22 cm. The remaining billets are collected in the form in the letter A. The upper part of the form A is the bars with a length of 22 cm, the side sides of the letter are a bars with a length of 32 cm, and the crossbar inside is peeling in the form of spacers independently. The connection is carried out using self-tapping screws and metal corners. The distance at the bottom of the letter must be at least 30 cm.

Sitting parts screw to the foundations obtained. After assembly, check the size of the second shop. The width of the shop should be 109 cm on the seat and 113 cm on the legs. Check the correctness of the assembly of the shop transformer can be visually visually, aligning the second shop with the first. If they attach them to each other and they form a sofa of 4-plates located at one height, it means everything is done correctly.

Go to the backrest assembly. For the back, we need 5 blanks, which form a common plane with a size of 126x57 cm. The connection of the boards is carried out with its own hands using a plank 57x4 cm (2 pieces). The width of the slats should be 8 cm. The planks associate the elements of the tabletop from 2 sides at a distance of 4 cm from each edge using self-tapping screws. With one side of the collected tabletop fasten 2 stops. The stops are made of 20 mm thick boards, drinking in size: length 40 cm and width 10 cm. On the one side of both billets, hepts at an angle of 115 °. This corner will correspond to the inclination of the backrest of the transformer. The stops are fixed to the inner sides of the worktop operators at a distance of 14 cm from the edge using self-tapping screws.

The back of the shop is installed on the stops tightly pressed towards the legs. In the stop and in the vertical board, a hole with a diameter of 7 mm is drilled. The compound is carried out with furniture bolts with a length of 8 cm. Metal washers are installed between the stops. The head of the bolt should not go out. The bolted connection must be moving and allow to change the angle of the table top. You can check the assembly by changing the opponent's backrest angle. If the angle is changing 90 °, you can proceed to the completion of the assembly.

Table boards used different breeds: birch, pine, aspen, but it is best to take solid types of wood for example birch, because the table and two shops are designed for 6 people, that is, the design must withstand high loads.

The advantage of this table is that it compactly adds to the bench with the back and back to the table with two benches, takes little space in folded.

So let's look at what exactly will need for the manufacture of a table transformer

Materials:
1. Plank 30x80 mm of different breeds (it is better to take birch boards)
2. Metal corners
3. Self-tapping screws
4. Car glue or liquid nails
5. Lac.
6. Morilka
7. Bolts M12.
8. Naka
9. Siaba
10. Nails

Instruments:
1. Hoven
2. Screwdriver
3. Drill
4. Hammer
5. LINE
6. Pencil
7. Roulette
8. Transporter
9. Corner
10. Brush

Step-by-step instructions for creating a transformer table:

After many searches on the Internet of the appropriate drawing, started working, first of all, right on the floor, rank pattern templates, you can also use plywood sheet.

Next, cuts the boards according to the size, the author used different wood species: aspen, pine, birch, but best to take solid wood. Please pay attention! Beepets will be two, but internal and outdoor. First of all, the master makes an outdoor bench, all the detailed sizes pointed to us right in the photos, which notice very comfortable. The height of the legs is 440 mm, the width of the arrangement of the legs at the bottom of 400 mm is very good for the stability of the bench.

Attention is an important point!
the length of the inner crossing is 150 mm, once again remind the crossing is located inside.

The length of the outer bench is 1380 mm, all the workpieces in front of the immediate assembly should be carefully glid and be sure to remove the face, so that the surface was smooth, smooth, as they say "without a bitch and zadorinka"

The bench turns out simple, and the fastening master does with the help of wood screws, joinery glue and for consuming reliability adds metal corners, as the design must be extremely durable.

So, go further) Now you need to assemble the inner bench Pay attention! The height of the legs on both benches should be strictly the same, but the crossing of the fastening legs is made out and its length is appropriately increased to 400 mm, the length of the upper strip 350 mm where 40 mm from the edge is drilled by a hole under the M12 bolt and drills to drown a bolt head in The cavity of the board, so that there is nothing to speak. All the necessary sizes the author pointed directly to the photo.

The length of the bench is 1440 mm, but in each individual case, the sizes can be varied, because everyone does under themselves, but as a standard we use the dimensions presented by the Master.

In the upper strip the holes are drilled.

After both benches are ready for them to try on and one must enter another with a small gap (see photo)

That is, two benches in folded form should create one unit.

That's actually what should happen in the end.

With benches, they figured out a bit, now we turn to the consideration of the author's further actions, namely the manufacture of brackets from a bar. The angle of connecting two bars should be about 100-1050 (see photo) where the bar "A" is responsible for the width of the table top, and the Bar "B" is height from the top of the bench until the countertop.

In the BRUS "B" the hole under the M12 bolt is drilled and drills to drown the head in the cavity of the wood.

After that, the obtained brackets should be connected to the inner bench, in place of the connection put the puck so that there is no pairing.

The head of the bolt is removed in the drilled hole.

The same thing from the opposite side.

In general, 2 brackets are attached to the height and width of the table top.

Then you should expand both brackets.

But now it starts the most interesting, you need to connect a worktop with an outer bench, this is done using a direct slap, its dimensions are indicated in the photo.

The data planks are required to produce 2 pieces, the author has long been tormented to get the exact size in the process of fitting, so that in each individual case there may be errors. For a start, the master drove nails along the edges of the planks and with the help of them made a markup, that is, he drove a nail so that he was a little sticking out on the other side and made a mark, and then drilled a hole under the M12 bolt

Everyone pre-carefully needs to be adjusted, and then calmly drill, as they say "death seven times, a rejection once."

It is necessary to make a limiter to this bar that the countertop cannot be reversed, for example the author, she looks like this.

That is, when laying, it will fix the worktop in the smooth position and will not give further move.

As you can see, everything is quite simple, the segment of the spilable board at a certain angle and is attached to the bar with 2 samples.

For complete symmetry in the second bar is all the same.

That's actually as a result of the work carried out.

This transformer table is compactly placed in the corner of the gazebo in its folded state.

Actually, what happens, the countertop turns into a back, and two benches are connected to a single integer by insertion into each other.

And if necessary, cover the table and arrange a "feast of the mountain" - just pull on the bench and the table is folded.

Voila)) And everything is ready.

The indisputable advantages of the Table Transformer are of course its compactness.

The author advises to use wood for the manufacture of a table of solid rock, for example, birch. This design is designed for 6 people in the unfolded form, so everything should be extremely reliable. Connection locations are additionally strengthened with metal corners.

Of course, this miracle table is quite difficult to make, but you are presented all the necessary sizes and descriptions, which was not from the author and he collected information throughout the Internet.

The dining area or recreation area in the country is important for each member of the family, as you can sit here with a book, taste the dinner or a kebab, who fucked my father.

Here you can get together the whole family to spend a summer day or evening by tea or just for interesting conversations about something important and urgent.

Stages of manufacture

Step 1. With the help of self-press, using a half-board sample method to fix the struck of the table legs.

Step 2. At the next stage, a sample of a wooden board should be made. Find the middle on the board and carefully cut the special grooves with knife. After that, the cut is performed until the middle.

Step 3. Wooden shop must be reliably attached to the table. Therefore, to build all the elements of the table and benches, as well as for attaching these two pieces of furniture, metal rods, nuts and washers are used. They must be well delayed so that the design details are not loosened.

Step 4. Now you need to consolidate bottom Tables using screws and nails.

Step 5. Collect the table top is very simple. It is necessary to first make a frame from bars located around the perimeter, and then attach polished boards to them.

Step 6. Attach the worktop to cruciform details with the help of self-tapping screws.

From the log, the table with benches is performed on the same principle as from the boards. Only the mount must be performed using the brackets that will reliably connect large and round elements.

The assembly scheme of such a table should also be prepared in advance so that during the process to know which details, what and where to fix it.

When making a wooden table bench, all movements must be taken carefully and carefully so as not to spoil the tree. Drops should be squeezed strictly in size, running around the place to cut the pencil.

Bench Transformer

The country-transformer bench is an original design that will be appropriate in the garden, gazebo or in the shade of branchy trees.

At first glance, this is an ordinary shop that can turn into a comfortable and large table in a few seconds. Such a piece of furniture can be made independently using conventional sweater materials.

The shop-transformer consists of five main elements:

metal frame base;
back, which;
fixing element for table top;
wooden seat;
fixer for the seat.

Stages of manufacture

Frame

The frame base can be made of a square metal pipe with a cross section of 25 x 25 and the thickness of the walls of 2 mm or a round metal pipe with a diameter of 17 mm.

Also need wooden plugs in the form of plugs. Pipes are welded with each other, and wooden tubes are inserted into the pipes at the ends.

Important! In order for the design to be durable and reliable, it is necessary to weld in the corners of metal inserts in the form of a triangle.

Back-table top

It will take plywood with a thickness of up to 20 mm and a wooden bar of 40x40 mm or 50x50 mm. Bruks are nailed in the width in the amount of 3 pieces with small nails or screwed by self-drawing. If there are some irregularities or roughness on the plywood, then its surface must be pulled out fine-grained emery paper.

Clamp fixator

This element is performed from thin racks. They must be attached to each other with a thick metal wire with a diameter of 10 mm.

Wooden sidushka

The transformer bench consists of a seating and a retainer. For the manufacture of the seat, it is necessary to prepare a wooden bar 30 x 30 mm and a slim of 60 mm wide. One plank should be 10-15 mm shorter to the retainer free Rose between these two details.

Seat lock

The latch for the bench is better to perform from metal Wire diameter up to 14 mm.

Self-collected garden furniture can become original Supplement Garden or yard near the house. Can do this way two Table benches or tables-transformer and put They are next to each other. It turns out a great place for tea drinking and holidays where you can place a large number of relatives and friends.

Table benches

In those places where screws were installed and clogged with nails should be used by a special woodspread. Apply and distribute the mixture with a rubber spatula.

When the composition freezes, all the missing places to stick to small emery paper. Before it, it needs to be consolidated for convenience on Broke.

The finish is of great importance for wooden products, operated which is planned outdoors.

If you do not produce the service life of the country's furniture can be minimal. For the finish finish, it is perfectly suitable for lacquer. It can be with a shade or completely transparent.

Note! If the noble varieties of wood were used to create furniture with a pronounced texture, then oil or natural shade oil should be used.

Regardless of the selected finishing material, it is necessary to apply it carefully and in two layers, treating all the surfaces with brush, and not just those that can be seen. After a varnish, the surface can be additionally covered with weather-resistant furniture coating.

Metal elements in the transformer table should be treated with an abrasive circle to remove the welds. After that, it is necessary to apply a paint coating that protects the metal from corrosion.

Thanks to such a finish, all wooden and metal elements of the table benches will be aesthetically beautiful, and the bench itself will turn out to be reliable and durable.

For details on how to make a metal bench and wood bench, see in the video:

All that is done on your own, is always interesting and nice. In addition, "self-made" make it possible to fly fantasy and implement the most bold designs. Especially a lot of space for creativity in those who have a cottage plot at their disposal.

"Self-timers" enable the flight of fantasy and the realization of the most bold designs.

One of the wonders of home mastery is the table bench a transformer, which can be made with your own hands on ready-made drawings or drawn independently. It is best to use millimeter paper: it will be performed most accurately on it the scheme of such an unusual product.

One of the wonders of home mastery is the table bench transformer.

Depending on the ideas about the possibilities of the transformer, drawings make; With their preparation, all the advantages that will provide this product are taken into account:

it compactly and takes a minimum of space, which will be an additional advantage in small territories;
its without any problems can be moved to anywhere;
universal in use, as it turns into a wide use.

The transformer can be provided with one or two benches, with backs and armrests, or without them. Their sizes will also determine the home master, based on the needs of the family and their own creative vision.

It is best to use millimeter paper: on it the scheme of such an unusual product will be performed most accurately.

In order for the product to be solid and durable, you need to choose the right lumber.

For work you will need:

edged boards;
bar wooden.

The product is compact and takes at least a place that will be an additional plus in small territories.

At the same time, the experienced masters claim that the suitable wood beech, ash, oak or birch. You can use and pine, but you will have to choose very carefully, avoiding the blanks on which there are many bitch.

Prepare tools

Universal in use, as it turns into a wide use.

To make the case without stopping, and time was spent as efficiently as possible, it is important to prepare the tools, without forgetting any trifle:

desktop tracing machine: greatly relieves work; You can perform operations and manually with fine-skinned hacksaw, and to apply the markup to use the transporter;
electric drill and drills;
plancock or milling machine for refoil removal;
cruciform screwdriver;
grinding small installation or block with sandpaper;
rasp.

The transformer can be provided with one or two benches, with backs and armrests, or without them.

Production Process: Step-by-step instruction

So that all parts of the product are at hand, the masters are recommended before starting work on the drawing. , where its elements are indicated, immediately prepare legs (8 pieces) up to 70 cm long, making on them downstairs and at the top of oblique cuts.

The strength and durability of operation depends on the accuracy and sequence of execution.

The next step will be the manufacture of table tops. You will need five boards with dimensions defined by the drawing .

They need to be polished and connect the planets width eight centimeters. Two connecting parts are quite enough.

All connect with self-drawers.

When will be ready for a bench , Tabletop screw to her.

So that all parts of the product are at hand, the masters are recommended before starting work according to the drawing, where its elements are indicated.

If a design with two seats are assumed, you can start the manufacture of the first; Its value depends on the general parameters of the product; According to the drawing, it is performed from the boards (1-2 pieces); Their amount is correlated with a width of the bench.

Seats are screwed to the legs;
both are strengthened with spacers.

The next step will be the manufacture of table tops.

The second shop is manufactured in the same way:

the legs make 40x40 bars; They are attached to the seat in the form of the letter "A";
parts of the bench join the timber, strengthen for the strength of joinery glue and self-drawing;
if it is assumed that a backrest is attached to the bench, it is drawn up from the boards, strengthened by bars, struts, joinery glue and self-drawing.

The next step is the assembly of the prepared parts of the product.

The next step is the assembly of the prepared parts of the product. To avoid unpleasant surprises, collect the transformer table, alternately connecting elements among themselves and referring to the drawing.

Designer thought can turn widely when it is time to decorate, especially convenient for this backlock shops and seats.

Nuance, making attention, is the observance of the same height of the details. If everything is done correctly, in accordance with the drawing, after the end of the work you will see an adorable sofa.

If everything is done correctly, in accordance with the drawing, after the end of the work you will see an adorable sofa.

The back is required to secure reliably; To do this, in places of connection, the holes are drilled where the furniture bolts are screwed.

Then check the correctness of the manufacture and strengthen the backrest . A simple safe way to check will be the opening and fixation using a conventional stick.

Then check the correctness of the manufacture and strengthen the backrest.

Fix them with wooden wrenches or gluing a joinery PVA.

For full amenities and comfort, you can mount armrests. For their manufacture you need:

two planks for stands;
four - for attachment to the seat.

If everything opens and closes unhindered, without much effort, the shops are connected to each other.

Fix them with wooden wrenches or gluing a joinery PVA. To complete this part of the work, you need to make a kind of lever, allowing you to freely add and lay out transformer .

Additionally, PVA glue and wood screws can be useful.

If the calculations are made correctly and the parts are connected correctly, it will be a wonderful table with two attached seats, which is easily disassembled and is collected.

It will take a bar, fixed with furniture screws and nuts, and with the armrest it is connected by self-drawing.

Decoration

If it is assumed that the transformer bench table will be on the street, to increase strength and a longer service it is worth painting and opened with varnish.

Designer thought can turn widely when it is time to decorate, especially convenient for this backlock shops and seats. They can be decorated:

drawings drawn by colored acrylic paints and varnish;
decamental paintings;
cute figures of funny animals caused by the electro-infringers;
electrolovka cut the beautiful floral ornament or figurines of the heroes of favorite fairy tales; Attach them with glue and self-drawing to backs.

To make things to move without stopping, and time was spent as efficiently as possible, it is important to prepare the tools.

There are many ways to make a homemade design incredibly attractive and original: it all depends on the desire and effort, and success will come true!