How to make a bar stool with your own hands, specialist advice. Bar chair do it yourself - the dream of any man bar stools from the old stool

Do you have a bar rack in your home or apartment, but there are no high chairs for her? The range in stores is not so small, but does not fit into the concept of the living room or kitchen? Nothing wrong! From today's master class you will learn how to make bar chair do it yourself.

Materials for legs of bar stool

The first question that you must put in front of yourself, how will the seat of your chair be soft or solid? If you do not know how best to do this in this case, leave the solid, as we did. If you do not like it, you can hide it at any time - tissue, leather or any other fabricated material. Below you can see the schemes and sizes of our future bar stool.

We start collecting legs

The legs of the chair we make a poplar wood - 5x5 cm, a long 71 cm. In order for the legs of steel under the slope to each other, it is necessary to cut the corners and chamdes on both ends. All connections are made using the technique described in this article.

We attach the middle and lower bar, similarly, at first, removing the chamfer at an angle of 5 degrees.

After you joined the two parts of the chair, which stand in parallel with each other, begin to screw the perpendicular partitions on one of such collected parties - from above and below. First, process one side, then the second.

Attaching partitions you must take into account their placement so that when the chair is ready for you to conveniently put legs on them. This is the bar stool and it should be convenient to sit on it!

Seat manufacturing technology

The special shape of the seat will make your bar chairs even more convenient. First you need to make a markup on one of the ends of the board, which we will use for the manufacture of the seat. To achieve the desired form, you can use a circular saw, adjust it to different depth of cutting, you can use a conventional pylon for this purpose. Cut the deepening, and then cut off the excess tree with the help of chisels.

Of course, this is a rather difficult way to make a deepening and it is possible to use some special tool, but it was not there. After you wrote a bit, you need to clean the surface of the seat with a sandpaper.

Connect the seat and legs

Complete our master class with a compound of the manufactured seat and legs. To do this, drill holes in the top of the legs and the seat below and using the glue to plant everything on the pins.

Clean the sandy paper surface of a new bar stool. If you need to fill the holes with putty, paint at the request of paint, or cover with varnish.

Ready bar stool

That's all, such three handsome, three heroes settled in our living room. Thanks to a selected height, the optimal placement of transverse crossbars and the ergonomic seat, they became the most comfortable and most beloved in our family. Want to do the same? There is nothing easier!

Interesting option to make bath chairs with your own hands

Owners of spacious housing, both apartments and houses, have the opportunity to add comfortable and beautiful elements to the interior. So, the bar racks are very popular.

Such racks require unusual seats. The length of which should be much higher than the medium torere. A similar chair can be bought in a furniture store, but you can make with your own hands. Such a process has a lot of advantages over the store:

monetary savings (almost twice);
the ability to independently come up with design;
good time;
a huge selection of materials and all sorts of colors will be given freedom of fantasy and desires.

Selection of material

Make a stool in two possible ways:

from wood,
metal.

The first option has more advantages over the second:

for assembly, it is not necessary to carry out complex technical work as a metal welding;
products have a smaller mass;
furniture from wood is much environmentally friendly, will bring more comfort in the home.

Any natural wooden material has its own characteristics on density and happens:

soft: Alder, Birch, Pine. It is easier to work with him, however such items are less durable;
middle: beech, oak, cherry.
solid: maple, tees.

Products made of dense materials will serve almost several generations, they become very strong and reliable. But the newcomer will fit soft in this case, it is worth only to take into account that their service life will not exceed 15 years.

Cooking drawing

Before starting work, it should be accurately determined with the design of the toaster, apply it on paper or make in electronic form for its convenience.

Standard conditional sizes for all similar chairs are:

height from floor to seating: 80-85cm;
length between legs about 40cm, width 30cm;
seat: 30 * 40cm.

Required tool and material

To assemble a tree stool you will need:

a hammer,
rolling
screwdriver or drill
sandpaper,
hacksaw,
corolnic
folon, fabric for seat upholstery,
stapler for furniture,
glue,
timber
paint or varnish,
morilka
wooden details:
4 things. ribs with a thickness of no more than 3 cm;
circle 2pcs:
the thickness of the first 2cm, diameter 26cm,
second - 3 cm, diameter 36cm;
feet 4pcs, 3 cm thick.

Assembly process

To collect the most simple bar stool from the tree, it will be necessary to connect all the prepared parts with the help of self-tapping screws, and for their better fix it is applied PVA glue.

The assembly process includes such a sequence:

the legs are connected between each other;
between them there is a small circle;
the top circle is screwed on top;
it remains to install rigidity ribs;
and after cleansing the sandpaper, apply: a veil and a minimum of 2 layers of varnish.

Note! If you wish, you can make your stool soft, for this you need to put a foam on the seat, top to cover it with a selected material, which is fixed on the back side of the stapler.

It is so very quick and easy enough to make a comfortable, beautiful bar stool for its rack.

In modern cuisine, there is often a corner for recreation behind a bar counter, for which chairs will certainly need.

Bar chair is a height-adjustable stool, which is designed for sharing with a bar counter.

Tools and materials

array of wood;
screwdriver drill;
lobzik;
sander;
plane;
roulette;
pencil;
drill.

To work, among other things, drills 3 and 6 mm should be prepared (here and then on the text the sizes will be indicated in millimeters). If after the manufacture of the chair it is assumed to be coated before the varnishing process, it is preferable to acquire a birch array, as the pine is characterized by an uneven stripping. Stocking to be treated with a thickness of 30 and 20 mm. The first option will go on a circle that needs to give a diameter of 360 mm, and it is necessary to use when conducting these works it is necessary to join. This element will become a seat. If there is a milling machine or a manual milling mill, you can provide an aesthetic profile around the perimeter. In the absence of such an opportunity, you can remove the champions using the plane, after which the treated surface should be stabbed.

The circle with smaller sizes, the diameter of which should be 260 mm, must be cut out of an array of 20 mm. The same material should be used for the manufacture of ribs of stiffness that will be filled with the role of footrest. They must be prepared by applying an array with a thickness of 30 mm, while it is necessary to ensure that the structure of the wood is located vertically.

Bar seat should be collected using self-samples of the following types:

5x80 - to pair the legs between themselves and a small circle;
5x40 - for fixing the seat to a small circle;
5x20 - To fix rigid ribs, items must be mounted with legs.

In details for self-tapping screws, it is worth scolding the holes whose diameter should be 6 mm, and in the end, the knocked holes must have a diameter of 3 mm.
After you managed to make a bar stool, you can cover its surface by the mourn. The layer must dry, after you can begin to apply lacquer.

Back to the category

Alternative design

Balaasins can be used as a bar stool legs.

You can make a chair with your own hands and on another sketch. For the process, it is necessary to use plywood with a thickness of 30 mm. The legs will be balasins, it can be replaced with cuttings for a shovel, their diameter is 30 mm.

Detailing (mm):

legs (4 pcs.) - Length 750;

seat with radius 180;

a draft seat with a radius of 170.

upper ring with an external radius of 143, internal radius 110;

the lower ring with an external radius of 153, the inner radius 120.

Before drinking the rings, they have to be placed to carry out drilling. On the workpiece you need to portray the outer contour of the element and spend through the center of the circle 2 direct. From the cross to postpone 140 in each direction, which will allow you to get the centers of the holes that you need to choose a drill. Now you can depict the inner circuit, drinking the ring from the flared element.

The draft seat needs to be placed as the top ring, but it follows the ½ thickness to the ½ thickness, it will be a "sockets" for the legs. The legs to the rings can be strengthened with screws. Under them need to drill holes with a drill of 6 mm. The upper ring should not be attracted immediately, insert the legs into the nests of the draft seat, where PVA is poured in advance.

The draft seat must be connected to the legs of 5x60 screws. Now you can move to the top seat of 4x40 screws.

The process of manufacturing a design can be completed with the tinted by the mourn and cover everything with varnish.

The next "last" product that has fallen in my blood practically at all stages. With its manufacture I had to strain and apply early skills and taste something new (about this later).

For the manufacture of this bar stool it came across a comment to one of my posts: "And you can do the bar stool?" and the beginning of the billet season. The fact is that the same mushrooms and other vegetables - fruit processing more convenient next to the sink, the washing is high - 85 cm. On the legs for a long time to stand it hard, and a simple stool is low. So I conceived my wife to make a high stool pathetic calling him "Bar Chair".

Photo for seed

Trouble with a chair began practically at the stage of acquiring a lumber. It was assumed to use a cross section of 30 * 30, however, due to its absence, it was necessary to buy 30 * 40, besides, it was designed that in the future demanded the recalculation of the entire structure, inconvenience in the production of one of the operations and the total minor, but still the rise in the cost of the project.

Let's start sawing. I wrote 4 brus with a length of 570 mm and 4 to 450 mm.

At first, he made two blanks from a long-short-long bar, then a couple of shorts pasted between them. And again I had to except clamps to use and fit out from grinding and circular.

From trimming plywood and boards prepared for the manufacture of seats made a milling box. Since bars of larger sections were used, the box had to do a larger size, dry more wood and the final stage of milling was made with the maximum extended cutter. It was necessary to dissolve the bars in size 30 * 30 as previously planned.

The stud on 8 passes through the entire rack (more correct it would be to use greater diameter bolts, there would be less vibration). It didn't work out to turn the drill, very large turns, and the milling mill stopped on the small. As a result, I had to tighten the hairpin with nuts and scroll through the blank inside the box with my hands constantly tightening nuts. According to a good, it was necessary to make a cutter, turning a 10-15 degree blank.
Milling box This one of those technologies that I wanted to experience. Experience received, conclusions are made.

One way or another, the rack was treated.

Next I make the seat and the footboard in the improvised bats. The seat and the footboard will be round, with a diameter of 310 mm. Glued together from two shields with the location of the lamellas across each other, as I hope it will give the necessary strength.

Using a plywood milling mill, a ring for which will be processed by the outer edge of the seat and steps, as well as the inside of the seat.

Something like this. Outside the milling cutter with a bearing, inside blindly along the copy sleeve.

Marking the steps: At the place, I put the central rack, circulated the contour.

In the corner, we set out where to drill transition holes. Feather drill played a tough joke with me - broke the wood, had to put a lot.

At first, I made a subtle drill where the tip of the pen will pass, then the pen drilled the holes of the required diameter and the jigsaws cut the section, after which everything align the sandpaper on Brous. It was necessary to make a template of plywood and holes to recover, the quality of the cut would be much better and would not have to kill a bunch of time to bring to mind with emery paper.

The result of putty wood breaks from the pen. Clay stolar moment d3 in this plan is much worse than D2 when machining the sandpaper, the wood is first eaten, then glue.

From the bars of the leg blanks are glued.

On the plywood pattern I give them a form. And then the nezenchik, the pattern breaks out from the workpiece (poorly secured nails) and the milling cutter spoils the workpiece. Bida - Pichal, the last trimming of bars went into business, just - just enough.

In the seat inserting a cross, she is collected on the grooves.

The legs also prepare the grooves for their assembly.

After milling edges and collect. It seems to be good. Then it was supposed to be a photo made in the title all prepared details for the assembly.

Seat grinding especially carefully.

Fitting chair assembled dry.

Conjugation of parts with each other.

First, all the details I painted separately, which eventually delivered trouble.
Not a water veil from "Novbythim" (Oregon and Ebenova) despite the cleaning of the tree from dust and wipes the White with alcohol, in the process of painting rolled into the swords. We had to spend them several times and smear the solvent. It turned out like this.

In the future, when applying a yacht lacquer "Chief Technologist" from the same Novbihim, it turned out that he dissolves the veil. Well, as a cherry on a cake when gluing parts between them, it would not be blurred by PUR-501, closed them with a painted scotch. Yeah ... When removing the scotch, the slices of varnish and the simulators remained on Scotch. (There will be no photos, since I specifically specifically). I had to re-move and repaint some elements. In addition, when trying to squeeze the vengeial place with a torn varnish, it turns out that it swept the varnish. Damn, it was necessary all the same to collect everything on the glue, and then burn and vanish.

But the result pleased me.

Cat does not please. For his ass is a little place.

Well, actually the reason for choosing such colors.

The wife hinted that she would probably need the facades to change the kitchen, so that wooden and in color with with a chair. And that the accomplices would be visible. :)
The total price of sawn timber is about 500 rubles (2 meters left twenty board). Two types of vehicles for 150 rubles (there are still 2/3 of the bottle of each), the varnish was purchased earlier for the table, half the banks left). Glue does not consider it, he spent little. Well, and one emery bar grid 180 for 70 rubles. Circles for orbitals, but a couple probably erased. And then, their fabric ceased to cling to hooks, the grain is still normal, they will be used to manual. In general, let the budget amount to 1000 rubles.
Chair dimensions: height 65 cm, seat diameter and steps 31 cm, legs along the edges of 41 cm.
Well, the last word. As I said earlier. I am not a professional joiner and not a hobbyst, you can call me a novice amateur. I understand perfectly well what could be done and better. The main motive of writing the post is to offer a variant of the manufacture of "bar stool".

Many owners of private houses or apartments choose a rack and bar chairs for their kitchen, since this option is more interesting. However, in stores it is not always possible to find furniture that fully satisfies taste, atmosphere, stylistics. Some produce a bar stool from the profile pipe or from other materials with their own hands. You can easily cope with such work, you just need to follow certain rules.

Tools and materials

The easiest way to create a bar stool, using Faneur, wood.

For the manufacture of homemade stools, you need to prepare the following:

workplace for the manufacture of chair;
screwdriver;
brushes;
roulette;
solvent;
electrolovik;
veil;

a hammer;
grinding machine or sandpaper;
drill;
self-tapping screw;
roulette;
plane;
bit.

It is also necessary to prepare selected materials - Fane or Tree. Some make metal bar chairs with their own hands, but such work is much more complicated. In the process of manufacturing furniture, a diagram or drawing with accurate sizes is used, otherwise there is a chance to make a mistake and spoil the product. Focusing on certain sizes, it turns out to know exactly how much wood or metal need, and prepare the required amount of materials.

The height of the chair is usually determined, focusing on the distance from the floor to the bar of the rack. The distance from the countertops to the chair is most often about 35 cm.

Wood

Among the wood materials are most accessible to birch and pine arrays. You can use some elements of old furniture.

Cut the following details:

4 stiffness ribs 3 cm thick each;
2 circles: the first 2 cm thick and a diameter of 260 mm, the second thickness of 3 cm and a diameter of 360 mm;
4 legs with a thickness of 3 cm each.

The substrate will be made from the small circle, from the large - seat. Make sure that the direction of wood fibers in the legs are vertical. Then begin to collect furniture with screws. Connect the legs with each other and with a small circle, screw the big circle to it, then screw the ribs. Tonnize the furniture using the veil, wait until the chair is completely drying. Apply to the surface of the lacquer (two or three layers).

Another version of the wooden chair is slightly different. It is very easy to do and convenient to use it. Seat data of bar chairs can be a toa with a cloth, bent or straight.

The procedure for such:

First make a drawing.
Carefully examine another drawing. To make it easier, two items that are under the seat are not listed here. Remember that they will have to add during the assembly of furniture.
To make legs, prepare the bars (3.8 * 3.8 cm). If there is no birch or pine array, you can use such wood as a poplar. The length of each bar is 710 mm.
Fasten an apron at the top (a small crossbar). Also attach lower and medium bars.
Then take the rack and secure the right of a longer crossbar. Then attach the bottom item, it will serve as a footboard.
The same must be done on the left side. To sit on the chair was most convenient as possible, determining at what height the footboard should be, orient to the growth of future owners.
Attach half of the furniture to each other.

To create a deepening in the seat, you need to cut it on the surface, and then exit using the chisel. Then the seat must be pasted and combine with legs, and then make grinding of the entire stool. As a final stroke, paint material should be applied to furniture.

If there is a need to stylize wooden furniture under ancient, you can use to form special means.

Another functional option is a bar stool with a recess and with a back. So the furniture will be as comfortable as possible.

For the back will need additional blanks.

Metal

Metal chair - reliable and durable furniture. In the process of operation, metal profiles, sheet iron, various trimming are used.

Take a flat asbestos sheet, which is used for welding, and mark the shape of the seat.
Focusing on the sketch, create blanks using 2.5 cm stripes.
To make the inside, prepare the elements of the same width.
Then the workpiece must be welded and clean up, rounded the angles.
Then the legs need to fight the legs to the seat (use profile 3 * 2 cm). By carrying out welding, connect the items at one point. The legs need to be carefully flexing until they take the required position.

Foot crossbars also need to be created using a 3 * 2 profile. Mix the places on the legs where the crossbars will be attached. It follows that what is the growth of a person for which this chair is intended.
For metal legs, it is worth choosing bumps from wood, and not corks from rubber or plastic. Wooden inserts will not damage the floor. If you need to resize, they can be treated. The letters can not be fixed with glue or screws, they will be well kept due to friction. It is only necessary to sublip them so that they are equal to the legs in size.
Now it remains only to apply paint material on the furniture. First you need to use primer. When the chair is dry, it is necessary to apply for the whole part below the seat paint black. After that, the furniture should be completely dryed again.
You need to close the black legs with a film so that they do not swap another paint, and paint the seat using a red dye.

Pipe

You can create your own hands with beautiful furniture made of metal pipes. Such a chair will be remarkably fit into the "Loft style" room. The furniture housing itself makes the pipes. It is better to stop the choice on chrome stainless steel. PVC or plastic is not to choose for such products, since these materials do not differ as high strength as metal.

Prepare the following:

foam, upholstery;
plumbing pipe bending;
Chipboard or phaneur;
fastening bolts;
metal pipes;
drill or screwdriver;
construction stapler and brackets for him.

Preparing a chair must be followed by the instructions below:

Decide which chair you will be made. You can see photos in magazines and further rely on them.
Focusing on the bar rack, think how much the tall chair you need.
Prepare pipes from metal that will serve material for the base. Determine the optimal length and cut the blanks. It is necessary to take into account the maximum burden on the furniture, choosing the diameter of metal blanks.

Using pipe bending, make the semicircular pipes. Billets need to be connected to each other using mounting bolts for this. So the furniture will become the most sustainable.
Using Fane or Chipboard, make the seat. Choosing its size, you need to focus on how much the person weighs for whom the chair is intended.
Using a stapler, cover the seat with foam rubber and upholstery. The fabric should be resistant to pollution, it is easy to clean, be suitable not only for dry, but also wet cleaning.
When the seat is ready, attach it to the place of connection of the metal legs. This can be done using fasteners, drill or screwdriver.

Decor

Many prefer to additionally decorate chairs created by their own hands, regardless of what material they are made. One of the most popular decoration options is the use of fabric. First you need to decide on a shade and type of material, while you should navigate for the overall design of the kitchen. To decorate chairs, tapestry, furniture silk, microfiber, jacquard are often selected. Some prefer to decorate furniture with various decorative elements, paints, paper, glue.

One of the most original methods of decorating is the decoupage, which allows to embody even the most bold design ideas into reality.

You can pick up different materials for the decoration and with the help of the decor make so that the usual chair has become a real work of art.