Connection diagram of a towel rail to the boiler. Installation of a towel in the bathroom: We set your own hands in the bathroom, video. Several illustrative examples of installation of towel rails of various models

The circuit of the heated towel rail to the heating system over the past decades has undergone several significant changes. Using these innovations, it was possible to achieve a noticeable increase in the effectiveness of this important element.

Traditional installation options for towel rail

To begin with, it is necessary to find out in what cases heated towel rails were previously used.

Connection diagram in an apartment building

The purpose of the construction of distant from the perfection of "Khrushchev" was mainly ideological motives - thus managed to achieve the resettlement of barracks and communal. For heating newly constructed residential areas, exclusively centralized heating was used. As a rule, the radiator was made in the bathroom combined with a heated towel rail. Such an approach had both strengths and weaknesses.

Advantages:

The heated towel rail additionally heated the room.
It was included only for the winter, in parallel with heating. When heat occurs, the device has been disconnected.

Disadvantages:

The bulky structures.
For its use had to pay extra.

This circuit of connecting the heated towel rail to the heating system provided for the presence of an additional pipeline in the basement. As a result, it was necessary to sacrifice the elevator and the garbage chute.

Two options for switching towel rails to the heating circuit and its accommodation are applied:

In separate bathrooms. In this case, the installation site performed an adjacent wall between the toilet and the bathroom. From the basement feed feed pipe, turned into an apartment on the first floor. Next, by passing the entire entrance, through the apartment on the last 5th floor, it turned out to be in the next apartment. Currently through all the floors, the pipe descended back to the basement. Shut-off valves in apartments did not apply in any form: only basements of the feed and reverse tube were equipped with valves.
In adjacent bathrooms. Here, the heated towel rail was located on the wall near the washbasin. It is important to understand that such a connection method was considered the most difficult due to the inconvenience of combined premises.

The most common series of "Khrushchev", where heated towel rails are switched not with hot water supply, but with a heating system, are:

1-434c - years of construction 1958-1964.
1-434 - Years of construction 1958-1967.
1-335 - Years of construction 1963-1967.

How to connect a heated towel rail in a private house

In the 1960s, private houses were not provided with hot water from central highways. Autonomous systems were mainly used on the basis of Titan-type wood boilers, which needed preliminary extras.

The reasons why such a hot water supply scheme could not be equipped with a heated towel rail, the following:

Design features. The cutting of the crane was carried out directly into the body of the apparatus, so the pipe for the drying of the linen was simply absent.
Temporary restrictions in the work of the heating device. One portion of firewood could provide only water heating in the tank.

The installation of a water heated towel rail has become possible only after water heating began in the private sector:

In the old scheme, how to connect a heating towel rail to the heating system, a direct switching to the heating boiler was applied.
Currently, the heated towel rail in private household is part of the general scheme where, besides it, also includes batteries and a warm floor system.

Reinstalling and servicing

With the advent of modern technologies, the question of whether to connect a heating towel to heating in Khrushchev, disappeared. Most often, this is solved by dismantling the old heated towel rail and electrical installation. To implement this solution, there is one serious condition: the rest of the entrances of the entrance should spend a similar reinstall in their apartments. Otherwise you have to hide the pipe to ensure the water supply of neighboring housing.

In addition, the relevant authorities should issue permission to carry out dismantling work: unauthorized reorganization of heating contours may result in serious penalties. Much less problems occur when connecting to the hot water supply of the side type of switching.

Stainless heated towel rail

The easiest way to solve the question of how to connect a heated towel to heating by replacing the old element to a more modern stainless product.

This solution has a number of advantages:

No need for reorganization of the heating system.
The level of heating of such a device is much higher.
The device has high decorative characteristics.
Materials are spent very little.

However, the fact that the heated towel rail can heated only during the heating season is a serious disadvantage.

Visual example of connecting to the heating system

For clarity, you can make out an example, how to connect a heating towel to heating in the apartment.

The order of work is as follows:

Scope of work. It is about replacing the old heated towel rail to a more modern stainless steel product, without changing the home heating scheme.
Dismantling. To remove the old appliance it can be simply cut off with a grinder. After that, the carving on the pipe is cut, for which you will need a handmade clus.
Installation of a sealing heater from a stainless steel. On the wall surface, it is necessary to make a preliminary markup of the placement of the device. For drilling mounting holes, a perforator is used.
Preliminary fixation. Using a ruler and pencil, the location of the polypropylene tube is 0.5 inches.
Welding pipes. Using a soldering iron, a new eyeliner is organized to the heated towel. Also installing a ball crane. If the ceramic tile is not yet laid, a stainless coil is recommended to be installed at the end of the finishing work.

As a result, it was possible to achieve:

Invaluance of the heating system. Constructive transformations were minimized. Only replacing the heated towel rail and the additional installation of two cranes was carried out. The presence of these elements makes it possible in the event of the occurrence of the flows quickly overlap the water supply.
The bathroom has become much more attractive. The bulky tube replaced the beautiful stainless "snake." The sale presents a sufficient number of design options, so that the selection of the most appropriate solution for a particular bathroom design usually does not cause problems.
The presence of forced ventilation will allow towels to dry in a short period of time.

Thanks to this description, how to connect a heated towel rail to a two-pipe heating system, if there are appropriate skills, an independent implementation of this procedure is performed. It is best to plan work in the summer: then you don't have to overlap the entire loop of the contour.

From how correctly the heated towel rail will be installed, its correct work, a comfortable microclimate and a bathroom design.

Depending on the condition of the supply pipe and the presence of skills, it can all last for several hours or delay at least a day.

Lovers of classics and what is simpler, do not bother and purchase a chrome coiner or a P-shaped heated towel rail, but uniqueness does not have to wait for such a decision. The most fashionable trend in which functionality and refinement are simultaneously combined, the Lestenka model.

There are also a lot of performance options, from simple single-section, up to having several sections, with the possibility of rotation mounted not only on the wall, but also on the floor and many others.

The most simple models may not require changes to the pipe wiring, but most ladies, and especially design items, imply a non-standard eyeliner and the distance between the inlet and output flanges.

The pipes were supplied from the riser to the location of the towel rail, should be placed accurately opposite the incoming and outgoing flanges, while only a minor error to the height of the ridge of the thread is allowed.

An increase in this tolerance is possible if the pipeline is made of modern plastic pipes with significant flexibility, without prejudice strength. Connection is performed through ball valves, at the inlet and outlet of the heated towel rail.

Connecting a heated towel rail is carried out only after turning off the water supply. Next, the pipe is inserted into the pipe. If the riser is made of ferrous metal, then at the same time change it, preferably on the plastic tube, due to the convenience of operation.

It is not necessary to change stainless steel risers, but the insertion in the metal is much more complicated, due to its rigidity.

Optimal, with the help of conventional welding, install metal taps, and to the place of connecting the heated towel rail to the plastic pipeline, which avoids the need to accurately measure the correspondence between the flanges of the device and water supply.

It is very important that the heated towel rail worked parallel to the riser, that is, if necessary, it was possible to overlap the water supply to it, without stopping the riser.

Ignoring this condition, and sometimes the owners during repair, specially cut out the area on the riser between tees, can lead to a breakthrough, due to significantly increased pressure and hydraulic shocks.

This connection option can be performed only if this is provided for by the water and heat supply circuit.

If the heated towel liquor was fed from the DHW pipe, then a new connection must be performed to it, while the transition from power from the heating system to the DHW, but not vice versa, in view of the difference of regulatory operating conditions.

When an autonomous heating system is equipped in the house or apartment, then the question arises: "How to connect a heated towel rail?"

Currently, an increasing number, not only owners of private houses, but apartments choose exactly this type of heating, because of its flexibility and convenience.

As a rule, double-circuit boilers are used, performing separately heated for a hot water supply and heating system, and here, the connection of the heated towel rail can be performed in three schemes:

to the hot water supply system;
to the heating system;
mixed connection.

The fact is that water heating contour works exclusively when it selection from the system, that is, according to the principle of the gas column. The boiler automatically ceases to warm water in the heating circuit and goes into hot water supply mode.

Connected only to hot water supply The device will quickly cool, after the end of the selection, and feeding from the heating circuit, it will constantly emit heat.

At the same time, we should not forget that the heating for the summer is turned off, so the latter scheme was most widely distributed.

With the help of the valve system, the supply is organized simultaneously from two contours. In the summer, when the heating is disabled, the heated towel rail is powered by the DHW system, in winter, the feeding from the water heating circuit overlaps, and the device works not only on drying, but also heats the room.

Greetings, Comes! Want to know how to connect a heating towel rail? And why such a scheme of the 60s is no longer used everywhere? Accuming sufficient experience, I am ready to tell about this method of connecting, maintenance and repair. And the photo report about the work done will clearly confirm my words. So, on the road.

Where meets

Let's find out where I used to have a similar circuit of connecting a heated towel rail to the heating system.

In high-rise houses

Apartments in "Khrushchev" have always been far from ideal, but they were built more in ideological reasons - to cut the barracks and communal. And since all new residential arrays were translated into centralized heating, it is quite logical that the heating device was combined with a heated towel rail.

This design has its advantages and disadvantages.

Pros:

The heated towel rail served as a heating device;
It was started to work only in the winter period, in the summer - disconnected;

Minuses:

Cumbersome design;
Additionally, the fee for its presence (in the heating season) was charged.

This installation of a heated towel rail required the laying of a separate branch in the basement, but such "additional costs" of states with interest overlapped with a refusal of elevators and garbage disposal. Let me remind you that the price of 1 m 2 of such housing managed to the state of only 95 rubles (prices 60s).

There were 2 ways to connect a heating towel dryer, and where to locate it in the apartment.

Illustration

Connection description

In separate bathrooms -on the adjacent wall, separating the toilet and the bathroom:

From the basement, the feed pipe went to the apartment of the first floor;
From the apartment of the top 5th floor through the entrance, it got into a neighboring apartment;
From there through all the floors back to the basement.

There are no shut-off reinforcements in apartments - the valves were only on the feed pipe and the return on the basement.

In adjacent bathrooms - on the wall in the area of \u200b\u200bthe washbasin.

Please note: it was the most uncomfortable connection option due to the features of the combined room.

The most common, in which the connection of the heated towel rail was not carried out from hot water, but from the heating system were:

series 1-434c - the year of construction 1958-1964;
series 1-434 - the year of construction 1958-1967;
series 1-335 - year of construction 1963-1967.

In private houses

Centralized hot water supply in the 60s in the overwhelming majority of private houses was absent. In an individual manner, it was carried out using a Titan type wood boiler, which was melted before applying.

Accordingly, connect the heated towel rail to such a hot water system was simply impossible:

due to design features - the crane crashed directly into the device body, respectively, the pipes on which the underwear could be dried, simply was not;
due to limited time The heating device - the wood laying was enough only to heat the water tank.

With the advent of water heating in private homes, it is possible to install and water heated towel rail:

Illustration	Description
	Old option How to connect a heated towel rail in a private house - from the heating boiler.
	Modern option - The heating towel rail in private household connects to the general system, including radiators and a warm floor system.

Replacement and repair

As a rule, the modern resident of "Khrushchev" does not suit the fact that outside the heating season is simply nowhere to dry the towel. And the most radical way to solve the problem is the dismantling of the old heated towel rail and replacing it on electric.

This method is possible if your neighbors on the entrance are collected in the same way. Otherwise, you will be forced to hide the pipe to keep the water supply to neighboring apartments.

It will also be necessary to obtain permission to a similar dismantling, since any interference in the heating system threatens big fines.

More intelligent is considered to be reconnected to the hot water supply of the heated towel rail with side connections.

And finally, the easiest way is the replacement of the old device more modern - from a stainless steel. This method has a lot of advantages:

The house heating system remains unchanged;
Improves the work of the device;
Improves appearance;
Material consumption minimum.

The disadvantage of only one - the device will still work only in the heating season.

Private case

I will describe the private case of replacing the heated towel rail in the apartment of his relatives. Actually, the instruction itself:

Illustration	Description of work
	Scope of work. We had to replace the old heated towel rail to a more modern stainless steel, without disturbing the heating system in the house.
	Dismantling: Sut the old heated towel rail; With the help of a manual clus, we cut the thread on the pipe.
	Installing a new: We celebrate the location on the wall; Perforator drill holes for fasteners; Fix to the wall (pre-); Using a ruler and pencil, we mark the place of the PPR ½ inches polypropylene tube;
	Soldering pipes. With the help of a soldering iron we make a new eyeliner to the toweling machine. Install the ball valve. The final installation of the heated towel rail was held after laying the tiles in the bathroom.

What did it give?

Firstly, The heating system remained unchanged, that is, the intervention was minimal - only a heated towel rail was replaced and 2 cranes appeared in addition. Neglect their installation is not worth it, because in case of leakage of the heated towel rail, it can be turned off to quickly;
Secondly, the appearance of the bathroom premises improved - instead of the bulky tube there is a "ladder" from a stainless steel;
ThirdlyThanks to the arrangement of forced ventilation, the towel dries out in a few hours even without heating.

In conclusion

I hope that I managed to answer all the questions of readers. Learn more about how to repair and connect the device in the bathroom. You can from the video in this article. Waiting for your additions and comments. Successes, Camrads!

The bathroom is a very important place for each modern apartment, because in this room there is not only the satisfaction of all the sanitary and hygienic needs of a person, but also washing, and sometimes drying linen. Due to the high humidity inside the bathroom, a complex microclimate is formed, which has a negative impact on the decoration of walls, ceiling or floor, the condition of furniture and plumbing.

In order to wash warm and comfortably in the bathroom, and the underwear hurts faster, a heated towel rail is installed on one of the walls of the room. In this article we will tell you how to properly connect a heated towel rail to the heating system or hot water supply.

What is a heated towel rail?

The heated towel rail is an additional heating device for the bathroom, which carries out the room heating to an acceptable temperature. Its device is quite simple, it is a curved tube, fixed with the help of special brackets on the bathroom wall. It performs the following functions:

Note! The heated towel rail is a curved metal tube that is attached to the wall in the bathroom. Metal is a good conductor, so it perfectly transmits heat to the surrounding space. Due to this, inside the bathroom becomes warmer, more comfortable.

Types of towel rails

Before connecting the heated towel rail to the heating system, you must select a suitable model. Plumbing shops have a huge assortment of coils for the bathroom. They differ in the material from which they are made, shape, diameter of the pipe, method of connecting and price. But the main characteristic is the type of heat carrier, which is used for heating it. The following types of heated towel rails are distinguished:

Note that from the point of view of operation, the most reliable models are water models of heated towel rails. They work reliably throughout the service life and rarely break. However, their functioning depends on the presence or absence of hot water in the pipes. The electric coil is warm, even the heating is turned off.

How to choose a snake?

- The routine operation with which even an inexperienced master will cope. Before starting installation, it is important to correctly define a suitable model of the device. When choosing, the following characteristics of the device must be taken into account:

Please note that for the successful installation of the coil in the bathroom, it is necessary to accurately determine the appropriate model. Maximum attention should be paid to the diameter of the pipes of the heated towel rail and the distance between the points of the connection. If these parameters do not match the connection location, you will have to use for connecting adapters that often become the cause of leakage.

Technology connection

The diagram of the connection of the heated towel rail to the DHW (hot water supply) is quite simple, so it can cope with this task without attracting a third-party wizard. When installing the coil is embedded in the general system of heating or water supply and becomes a necessary part of it, so it is necessary to approach its installation very responsibly. This operation is performed in the following order:

Please note that if the coil model belongs to the water type and works from central heating, it is recommended to replace or repair a heated towel rail at a time when the heating issue ends. If you have to perform work during the heating season to overlap your riser, you need to contact the management company.

Mounting errors

Experienced plumbers believe that the circuit of connecting the heated towel rail to the hot water riser is so simple and understandable that even a non-professional master can cope with its embodiment. However, when installing, problems may arise that affect the operation of equipment. The fact is that the water in the coil pipe is fed under pressure, due to which all points of the connection are exposed to a large load. Most often, the malfunction during the operation of the heated towel rails occurs for the following reasons:

Important! Connecting a heated towel rail to the hot water system in apartment buildings is usually performed directly to the general riser according to the project. Working pressure inside the coil is at least 6 atmospheres.

Video instruction

Be able to quickly dry things regardless of the time of year, then for what we purchase towel dealers. In order for no problems with ways to connect the device to the hot water supply system or heating, it is recommended to purchase domestic products. Russian manufacturers create models less susceptible to corrosive processes, in contrast to European analogues. Moreover, you will not have a question how to connect a heated towel, because the diameter of the product will be obviously coincided with the standards adopted.

To date, consumers are offered heated towel rails of three modifications:

with ten
water
combined.

Combined

Installation of the heated towel rail is available for water models. Here you can handle without assistance. Connecting an electrical or combined type device requires specialized skills. You will need a professional electrician intervention:

water and combined models are more limited in places of installation. The bathroom heated towel rail provides the ability to use hot water supply pipes or heating. This method of accommodation is most traditional for Russian housing and is convenient for drying linen and towels;
the heated towel rail has its own inner medium, which heats up under the action of the Tan. Such a model can be mounted in any convenient location subject to the available power supply.

If you have to replace the old heated towel rail of the Soviet sample, when you buy a new model, select a device intended for a lower connection with a similar diameter.

The most optimal is a water type heated towel rail. As a result of connecting to the hot water system, you get a device operating all year round. The ability to control the flow of water allows repair and installation work regardless of the season.

It should be remembered that the connection of heating towel rails imposes a seasonal restriction on its operation. You can quickly dry up the underwear until the heating season lasts.

The same concerns the possibility of mounting the heated towel rail when connecting to the heating system. To attach a heated towel rail and connect it will need to wait for the summer period. Nobody will allow you to cut into the heating system in winter, since these manipulations cause the frosting of the riser.

The pipes hidden in the wall, having an outside exceptionally outputs, allow you to install a water heated towel rail with side connections. It is believed that the installation of a similar sample is more time-consuming, however, aesthetically, the device looks much more profitable for other models. Also pay attention to thorough waterproofing of the connection. The elimination of leaks in this case will be an extremely difficult task.

Technology for connecting heated towel rail

The easiest technology of connecting electrical models. There are no complex compounds here. The process of properly connecting the heated towel rail lies in fixing fasteners on the wall near the stationary socket, subject to the rules of electrical safety. This means that splashes and water should not fall on the device. Recommended minimum distance from a 2,4 meter bath or shower. Electric heated towel rail can be installed anywhere at home.

With water and combined models, things are more complicated. There are two stages of work. Disassembling the previously connected, old device and installing on its place new.

Materials and tools

Before connecting the towel rails to the hot water rising scheme, you need to decide on the list of required materials and the toolkit, with which the device is connected by the DHW system or heating. For successful installation and correct connection, you will need:

heated towel rail with diameter corresponding the size of the pipes in the system;
brackets for fixing the device on the wall;
couplings and fittings;
drills and dowels for fasteners of brackets;
knife;
pipes Ø 23 or 32 mm;
2 -3 ball valves;
apparatus for welding used pipes;
adjustable type key;
tees.

For electrical type, only the proposed list will be required heated towel rail, Brackets for fasteners, drills and dowels, with which the device is attached to the wall surface.

Ball Valves

Overweight American (coupling)

Pipe welding soldering iron

Pipe cutter

Answering the question to how to connect a heated towel rail, go to the first step - dismantling the device installed earlier. First of all, it is necessary to overlap the water supply. If it comes to the heating system, then all manipulations need to be pre-coordinate with the super-guidelines-management company or HRKOM.

If your device is connected to the system pipeline by means of threaded connections, then you need to unscrew them and remove the towel rail from the fastener. When it comes to the heated towel rails welded to the pipes, resort to the use of the Bulgarian, leaving a cut of the pipe, on which a new thread cutting will be produced.

Dismantling of an old heated towel rail

So, the algorithm looks like this:

water supply overlaps in system pipes;
a threaded type connection is unscrewed, the device is removed;
bulgarian is used solely if the heated towel rail has been welded to the pipe, or because of the time connecting the thread bought and unscrew it is not possible.

If you are planned heated towel rail In the process of repair work, it is necessary to put mark on the wall where the device will be mounted specifically. Channels are stroke for pipe supply. At the end of this procedure, you can move the following step.

When dismantling the old device, it is necessary to take into account that the lengths of the remaining pipes should be enough to cut the new thread

Installation of cranes (bypass)

Bypass - Pipe jumper for installing ball valve. It is required to circulate water in the system if it became necessary to disable heated towel rail. The installed crane will allow feeding or overlapping water for redirects via bypass. For electric heated towel rail It is not required.

For the manufacture of bypass take pipes from the same material from which the system is made. The best option is the stainless steel. This is a durable, resistant to interaction with pipeline water material.

Views of Bypassov

When mounting the bypass, ball valves are initially mounted. If there were no threads on the pipes used, it is cut. Next, at the entrance and outlet of the serpent heated towel rail installed one crane. Be sure to provide high-quality sealing of compounds. Otherwise, in the future you will have to eliminate leaks.

Bypass is not a mandatory element when installing heated towel railworse function The device will not. Bypass is required in case of emergency situations, such as education in the connection zone heated towel rail and leak pipes. It is possible to block the water in the riser, but in this case you will have to wait until the breakdown will not be eliminated, while staying without hot water supply. Not the most convenient option. When heated towel railsconnected to K. centralized Heating and water supply systems can be a real problem.

Bypass installation will allow the ball cranes to overlap the water supply to the device. At the same time, the water will continue to circulate on the main system. To remove air bubbles to the bypass, another crane is installed in addition to the available.

Installation of towel rail

For connecting a heated towel rail with pipes you will need fittings. They can be straight or corner. Fittings are connected to pipes by welding.

The work algorithm is as follows:

water supply overlapped in riser. When carrying out work in multi-apartment The house needs to be agreed with the actions with the organization churring the flow of water;
install Three cranes - at the entrance and outlet of the serpent heated towel rail, And one more on the jumper bypass. This will allow in the future it is easy to replace or repair heated towel rail;
mounted on the walls of the brackets or other fasteners for the instrument. There should be a maximum distance between the wall facing and the device. For pipe diameter Over 23 mm, it must be 50 mm, if the diameter is less than 23 mm, then leave the gap 35 mm;
further, pipes with welded fittings are connected to the instrument. Be sure to use the linen winding to seal the connection location. Gently, not to spoil the thread, tighten;
check out the result for tightness. To do this, the system is submitted. With properly produced works, the flows will not arise.

Marking before installation

From above, vertical elements of the heated towel rail will be fixed in the rings of brackets

Collection of heated towel rail

Installation of towel rail

This algorithm will allow you to qualitatively connect the heated towel rail so that it will work for a long time and consistently. If you wish, you can install your own hands.

Connection schemes

When connected with a diagonal or lateral method, it is necessary to have taps at one level with the inputs of the dryer. Permissible only a small deviation. If the location of the taps turned out to be less than the length between the inputs heated towel rail, then scheme function will not be .

When connecting, the taps must be mounted strictly horizontally. The maximum allowable deviation distance is about 2 percent, that is, 2 centimeters per 1 meter. The slope is determined depending on the selected scheme and how the end of the pipe will join the removal.

Connection	Heated towel rail	Hot water supply direction	Location of taps	Normal day need
Lower	Lestenka	Anyone	Below the edge of the dryer	Efficiency maximum. Installation on the upper conclusions of the air vent - mechanical or automatic. Treads - pipe; The diameter per 1 step is less than the diameter of the riser. Bypass - straight, with a seed with a pipe for 1 step of a smaller diameter.
Lower	Lestenka	Admissible feed from above	The edge of the dryer between the discharges	The efficiency is reduced. Upper removal is allowed to mount the dryer niminator.
Universal lateral	Any standard form	Top feed	Horizontally, minimal deviation is allowed	Bypass - straight, outlined. On the ladder, the air ventures are not needed, leave the plugs. At the top feed, the seeds on the bypass pipe on the step of a smaller diameter or the jumper offset closer to the device will increase the efficiency.
Universal lateral	Any standard form	Top feed	Location of the top removal below the top of the dryer	Requires the installation of Maevsky cranes for air booming
Diagonal	Lestenka	Functions at the top feed	Top tap - to the far edge; Nizhny - to the Middle	Efficiency is equal to efficiency when connecting on the side. It is allowed to be separated and biased bypass.
Diagonal	Lestenka	Feed from below	–	Bypass without searches, clearly for riser.
Depending on the model	Common towel rails, non-standard form	Depending on the hydrodynamics of the product	–	–

Schemes will work properly provided that the taps are executed directly. Any bends, rings and arcs are the field of air accumulation. An uneven removal of water leads to a blockage of the pipe with an air plug, up to a complete circulation disorder. Also disturbing the circulation can fittings with strong narrowing of the lumen. Inside the system, nothing should increase hydraulic resistance. Water current must be free.

Scheme of fastener and connecting heated towel rail

Connection diagram of a heated towel rail to the pipe of Gvsshem for three types of connection (lower, side and diagonal)

Features of the installation of a combined design

Most often standard heated towel rails function only for the period of heating. Owners of apartments to get the opportunity to dry the underwear at any time, set the towel of the dryer combined Type that can work from both the heating system or DHW and the power grid. To do this, an installation of the Lestenka type in the lower left liner is made electric heater equipped with a thermostat. Connection scheme heated towel rail To rising hot water or the heating system will look like this:

when the cranes overlaps the device is filled through the eyeliner on the left at the top on which installed Maevsky's crane;
towel dryer Folling, acquires Wednesday thanks to which heating from the Tan.
If it is turned off from the outlet and open the cranes, the provision of hot water from the central system will resume.

For a sobminated heated towel rail, water is also needed

It is necessary to provide a place for a rosette with grounding for a heated towel rail

Remember that dryers have high power consumption. That is why they require a separate socket to which the cable is suitable can withstand the high voltage and is powered directly from the electrical tailor. Such a line in the wiring is necessarily provided by a separate machine. A common network combined dryers will not connect without risk for wiring. It is very important that the correct grounding is made. If you do not have an electrical installation skills, take advantage of the help of specialists. They will help competently install the device and provide high-quality power supply.

The competent connection of the device will bring apparent benefit and convenience when drying things. Most importantly, competently approach the installation process. The devices will save your time significantly, regardless of the season.