The hallway creates the first impression of the interior of the house, should have a beautiful design, be comfortable. It accommodates furniture of various purposes: closet under clothes, mirror, bedside table, hanger, chest of drawers. It is also nice to put furniture for seating: a bench, the chair will complement the design. So, the hallway allows you to choose any design as in the photo that the owner of the house wishes.

When creating an entrance hall, you can use drawings, diagrams, photos that can be found on the Internet or create your drawings. Create furniture will be easier if you use drawings. The design of the hallway takes not the last place in the interior of the whole house. It will be good to look at the Furniture Furniture Photo. Supplement wooden floors or laminate design.

Any of the elements of the hallway can be created with their own hands.

One sash

Production Stages:

• work begins with the preparation of the canvas with dimensions of 1700x400x18. Marking is applied to it, the side part is cut. The next element is the shelf, the bottom. Next, we work on the front side, which is attached under the bottom of the photo;
• when everything is ready, the holes are cut to which the wovers are attached for furniture. Places for drinking are chosen at their discretion. If the facing is made by a plinth, then the place is cut on the place so that the drank part approached it tightly;

• go to drinking the door: it is better to use the material from which the framework is made. Drink holes under the loop. It is better to choose a loop with which the door is closed at the level of the base of the couch. Loops, when installing which the door shifts from the base, it is better not to take;
• the next stage-promotion of the glue of the shelters and holes. Then the specks are installed in the holes and glue the frame. When the parts are fully assembled, it needs to be secured by self-drawing. Only after the door is attached;
• cut the share, drawers are installed on them. They are located in the entire width of the side wall. To make a force, you will need a sheet of plywood from it you need to cut two web width somewhere 16 mm. When the pollows are ready to attach them inside, where the bottom of the drawer is located;
• after the time is installed, you can go to the creation of the drawer of the drawer. Drink the bottoms that are made from plywood;
• cut the back wall from the boards, two sides. After they are made screw the walls with self-draws to the bottom.

To prevent cracks in the plywood, before screwing the screws, you need to make holes. It remains to be made only the facial part of the drawer. We make the upper part, cover and secure it to the body, edge for furniture.

Double bivalves from wood

The process of making a bedside table with two sash is similar to a single bedside table. Initially, the frame is made, we put markings, then drink. On the sides, the slots are performed so that the bedside one is tightly adjacent to the wall. Further cut the bar under the shelf of plywood. Dimensions are the same with a single bed.

Most often a few compartments. One department takes a quarter of the entire design to the width, and in the height all the place. The remaining place occupies the second branch. It is divided into two parts by a horizontal shelf.

All parts of the tree are bonded between themselves, they are pre-punctured and sets are installed, as shown in the photo. After all parts are fixed with self-draws. Next, cut the door and install so that when closing there is no deviation.

DRAWING DRAWING CUMBES FOR HOME

Hanger

When making hangers, we select several wooden boards. Boards must be the same length. Describe the option how to make a hanger from blocks, optionally you can make a hanger with a large number of blocks:

• lays the boards to the surface so that there is free space between them. At the top of the hangers, they are attached to the rake at the level of where the hooks will be attached;
• go to the manufacture of shelves for hats, its size completely coincides with the size of the hanger;
• when the shelf is prepared, it is attached to the hanger with self-draws. On each side of the shelf attaching ribs so that the hats do not fall from the shelves;
• now that everything is ready to fasten the hanger on the wall, where they planned to attach it. If the boards are long, then they should be cut to the cabinet level. When the hanger is shortened to the desired level, you can use.

Pencil case

In the production of Penal, there is nothing complicated. It is necessary to purchase a furniture shield, cut out of it: wall, bottom, front part, lid, two rear walls, they cut the place for the plinth, so that the wardrobe fits tightly to the wall.

Work plan:

1. collecting frame. Initially, we wash the melting for furniture holes and seasons. After they are attached to the places, collecting the frame, then it is fixed with self-draws;
2. now drink two canvases that will serve for sash. In each of them, the holes in which three loops are attached;
3. now we determine how much shelves will be. We divide the height of equal compartments, for each shelf and install fasteners at the desired level;
4. cut the shelves and install. At the end of the work attaching the sash.

Wardrobe Making Scheme
Case - Pencil Pencils with Open Shelves
Ordinary wardrobe

Cupboard

Consider how to make a closet that can be placed even in the smallest hallway design. It will be installed on the legs that are attached to it by self-draws, they have a height of 55 cm, the size of the screws 4 × 16 is thus the gap is formed below. More information is not needed about the data support, now we will pay attention to the assembly. First, we will define the size of the details.

Cabinet in the hallway

Materials for creating:

• Laminated chipboard;
• organit painted;
• melamine edge, the basis of adhesive.

The facade is performed under the order, it is made of an aluminum frame, attached to three loops, a photo mirror is fixed in the frame.

Preliminary drawing of the cabinet

This is a more expensive option, but you can use more budget. The mirror can be glued to the chipboard sheet using special photo glue. It turns out a bulky and heavy facade, relative to the custom version. For him, it is necessary to purchase at least 4 loops, the closet is better to attach to the wall, it will be more reliable. Otherwise, he will fall when the door opens. Therefore, it is necessary to determine the option of the facade.

To collect the framework you need to purchase sheets of chipboard of the following sizes:

• 1 sheet 390 x 460, cover;
• 2 sheets of 990 x 480, top, bottom;
• 1 sheet 380 x 390, shelf;
• 1 sheet 2110 x 390, backdrop;
• 2 sheet 2110 x 460, side parts;
• 1 sheet 400 x 440, side sides of the bedside tables;
• 1 sheet 570 x 430, shelf;
• 1 sheet 400 x 365, door of the couch;
• 1 sheet 2030 x 600, rear wall.

Measurements in millimeters.

Card cutting chipboard
Card cutting DVP

Before making a closet, you need to select a place where the places that are often used are not closed. Frame to connect easy.

When collecting, use tools:

• screwdriver with high power;
• tree drill steam pieces;
• set of fasteners, with a hexagon for confirmates;
• pencil;
• line;
• a hammer.

Furniture tools

Specialized accessories:

• retractable Plank: Length 410 mm. It is attached to the shelf below. Handers are placed at the level with the front part;
• four hinged internal loops. 6 pieces (2 pcs. For a shoe bedside table, 4 pcs. For a large door);
• hooks, handles: create design, the choice is varied.

Required accessories

For coincidence of fasteners, the inner shelf is better to place 35 mm above. Produce screeds to confirm. Under them in the end and in the plane chose the details. Fasteners standard 5 by 73 mm. In the plane of the holes through a diameter of 8.5 mm. Marking is defined depending on the number of parts. Such as sidewalls, facades, an open part.

The organs are fixed with self-proofs or nail with nails. If free time is enough, it is better to choose the first method. The second way is better to choose if you do not have a large margin of time. In the first and second option, it is important to comply with the design remains rectangular. If this requirement is not respected, then the facades will look unattractive and will not be able to close well.

Cabinet behind the door

Place behind the door is ideal for placing a wardrobe. Having installed it, the wall will be protected from damage that the door handle can do. It will take an inch board, the ray, which is previously covered with wallpaper and covered with varnish or paint. Varnish use if the wallpaper is suitable for the design of the room. Paper for pasting applies so that the board does not occur during operation.

Cut the blanks similar in size with the door:

• side rack;
• shelves.

Parts are connected by self-masses, with large wicker caps. Shelves are attached to the wall with the help of corners or rails. Rack on the side is fastened with corners or hidden fastening.

Behind to the end is installed canopy loop, the self-tapping screws into the wall and the loop with the sidewall is put on it.

Mounting doors on a closet

Hidden mounting can be applied for shelves. If the cabinet is fixed with hidden fasteners, then if you need to easily remove it. How to make your hallway, and what design to choose only the owner of the house can solve, and use the recommendations that are given in this article or not, it is only his decision.

Sometimes the assortment in the stores is striking by its monotony. Many apartment owners know that it is very difficult to choose furniture in the hallway. If the room is small, then the cabinets are simply not placed or filled with everything free space. But the owners of spacious vestives fall into a difficult situation - the presented models do not always meet the demands of the owners and often look ridiculous in a large room.

If you cannot choose a suitable cabinet, then do not beware and think about creating perfect furniture for the hallway with your own hands. Such an approach will save money, as well as get a model that suits you in all its parameters.

Can it cope with such a task a beginner "home master"? Yes, the desire and availability of all necessary tools and materials will lead you to a positive result. Of course, inexperienced masters it is better to stay on the simplest models. But those who are already far from the first time making furniture can create a real work of art.

To make it easier for you to deal with difficult work, we have prepared special instructions, drawings and schemes.

How to make a hallway do it yourself?

To begin with, you should decide on the model and sizes. If we are talking about a tiny room, then you should not overload it with furniture - use the standard entrance hall with a small compartment for the outerwear, shoes and necessary things.

A spacious hallway can be placed a spacious wardrobe. If the area allows, then such a closet will easily turn into a real - the dream of each woman. The cost of implementing such a complex project increases in proportion to the size and filling of the cabinet.

You can also consider the option that will be a compromise between the capacity and appearance. So, the angular halls visually look much less. But at the same time the high depth allows you to place inside a lot of things.

Choosing a suitable model, you can start withdrawing the measurement and preparation of calculations. Also be sure that you have all the tools that the wizards enjoy.

Necessary materials and tools

Prepare in advance:

• saw or electrolovka,
• screwdriver
• emery paper
• construction knife,
• furniture screws,
• roulette
• corners
• loops.

You will also need material for the manufacture of a hallway. We recommend to give you preference to the furniture shieldBecause it is made of natural components without using synthetic resins. Such a shield is completely safe for the health of people living in the house. However, this material has a high cost.

More popular with popularity common Ledp.. It includes fastening resins that can negatively affect the tenants of the house if the edges of the laminated plate will not be closed by edges. But at the same time, the material has a relatively low price and excellent characteristics (it is easy to operate with it).

Standard entrance hall with your own hands: instructions, schemes and drawings

To make such a simple hallway, you will need the following materials.:

• loops - 12 pcs,
• furniture shields - 7 pcs (dimensions 1600x400x18 mm),
• plywood segment 6 mm,
• bounded boards - 2 pcs (dimensions 2000x240x18 mm),
• furniture handles - 6 pcs,
• three-dimensional rack - 1 pc (3000x40x12 dimensions).

We recommend you start with Penala. Its dimensions are 2000x400x400 mm. The corresponding planks, as well as the upper lid at the calculation of the "Vansel", are peeling out of the furniture. Also two shelves will be required. The assembly is quite simple. The planks are located in parallel and fasten in the lid with the help of self-tapping screws, the shelves are also installed. For strength in the corners, the frame is fixed by corners drank from plywood.

Since two doors located in each other are much easier than one, then this option is preferable. From the shield you need to cut two identical doors and several internal shelves (optional). Secure the doors on the loop. You can do and two per door, but for reliability and proper weight distribution, we recommend using three.

The dimensions of one tube constitute 400x400x820, and the other - 820x400x490 mm. You can refuse any of them without prejudice to the design as a whole.

To collect the first tumb You will need 2 identical sidewalls and an inner regiment, which will close the design below. The upper part of the future stands is strongly narrowed, so the lid should be noticeably less than the main part. All elements are fastened with self-draws. If you wish, you can use furniture wanks. Do not forget to drill holes in advance and use glue.

The door is cut from the shield for the bedside table, it must be fixed on two hinges. But for the drawer, it is necessary for a slide. We recommend that you purchase the necessary items in a specialized store. You can make them yourself from plywood, but in this case the box will be pulled out, and not roll out, which will complicate its use.

Make the second tumba very simple. You need only two sidewalls and 2 internal shelves that form a frame. Internal filling of this tube can be completely any. All items are attached to the self-tapping screws or the sewage.

After that you need to collect the hallway. All items secure each other, and then prepare the boards. They should be beautifully located from the edge of the foam to the edge of the cabinet, creating the basis for the hanger. Constore the same step, attaching the boards to the possession of the bedside tables. So that in the top of the design is also durable, secure the boards to the rail. Place it at such an altitude so that you can later attach to the rake hooks for outerwear. If you wish, you can supplement the design shelf for hats.

Do not forget to open the hallmarks with varnish, attach the handles and hooks.

Wardrobe Hoodie: Instruction, Schemes and Drawings

Make a lot easier than it may seem. But to begin with, it should be declared the exact value of this term. The "wardrobe" suggests a special design of the doors that move around the cabinets along the cabinet case. It can be both built-in and standing separately.

If desired, you you can make a cabinet case of drywall And thus hide it in a fake wall. But we will look at the classic scheme for making a wardrobe with side walls.

This model with dimensions 2020x625x2320 consists of several main parts.

• Side racks must be a height of 2288x625 mm (the thickness of the top and bottom sheets is taken into account in these calculations - 32mm).
• Also large details are the lower and upper strips: 2020x625 mm.
• Middle vertical racks are inextricably linked with a rod for clothing. As a rule, it is attached at an altitude of 1900 mm, so the standard size for them is the height of 1900 mm, the width is 525 mm. The remaining 100 mm is a stock for the normal functioning of sliding doors.

The filling of the cabinet can be any. It all depends on your desires and preferences, but remember that inside there should be a stock for the placement of fasteners.

All items are best booking in a joinery workshop. To cut the elements of the desired form at home will not always be able to even an experienced master.

After that, you can seize. For installation, we recommend using not only screws and ducks, but also furniture corners. Rails are installed inside the cabinet on a specially designated area (those 100mm, which we left during the workpiece of parts). After that, you can put the door and use the cabinet.

Corner hallway with your own hands: instructions, schemes and drawings

The problem arising when creating an angular hallway is that careful calculations are required, the slightest error can cost a whole sheet of material. First you need to remove the measurements and check the walls. If the surface of the wall is a curve, then without a common frame can not do. Otherwise, the walls themselves can serve as the basis for which the shelves can be fastened. The second option is more economical and easier, but we will look at a separate cabinet, because perfectly smooth walls are a rarity.

Choose a suitable drawingBased on the size of the room, the length of the walls and proximity of the doorways. Treat the inner equipment of the cabinet. According to the selected sizes, make six basic hull elements:

• lower and top planks,
• rear walls (2 pcs),
• side walls (you can do without them, but the functionality of the cabinet will decrease).

As soon as they collect the frame, you can start installing internal shelves, baskets and drawers, as well as hooks and rods.

The angular hallway can be equipped with doors on the rollers, turning the structure in the corner compartment. But budget dispensers will look good.

How to make a hallway do it yourself: video

When people come to the house, the first thing they see is an entrance hall. Each person, for the first time, crossed the threshold of your dwelling first, sees the hallway, thereby making the preliminary opinion about you. That is why the hallway furniture should carry such qualities as elegance, beauty and practicality. The main task of the hallway is not only a decorative and representational function, but also the preservation of your things in due state and in general, order in the house.

Hallway is the face of the whole of your home. From the entrances you in the morning go out on your affairs, in the evening, come back in it. Therefore, it is necessary to carefully think about the design of the hallway. It should be as comfortable as possible, practical, beautiful. The size is chosen on the basis of what size you have room. Since it is in the hallway, in those cabinets and shelves that in it are set, most of the clothing is stored, then you need to go with the mind to choose furniture.

Of course, you can buy, but it will be much more interesting and cheaper to make it make it with your own hands. And if you have children in the family, you can also attract them. Then the process of creating furniture to turn into a developing program, especially for boys, which on an example of an adult will learn to independently do this or that device. The author of this master class decided to independently make an entrance hall for his home alone. And that's what happened.

For work were used Furniture shields 1600x400x18 mm - 7 pcs. 2000x400x18 mm - 3 pcs, Boards 2000x120x16 - 7 pcs, 2 Twelled boards 2000x240x18 mm. 1 three-meter rail 3000x40x12 mm, piece of plywood 6 mm, furniture loops - 12 pcs, furniture handles - 6 pcs.

At first he began to make a bedside table, dimensions of 820x400x400. On the frame there are clear angles in the upper part of the side walls, so that the top cover of the couch was a little already the most of its main part. Basins were produced by self-drawing. Do not forget to cut into the bottom of the bedside tables under the plinth. Next, the front plank is attached, which is attached to the seasons.

After making the cabinet, the door is made for it, the dimensions of which are 400x400 mm. Holes under the hinge drill a special drill. Fresh door.

The next step is the manufacture of polls for the drawer, which will be located at the top of the couch. They are cut from plywood 6 mm. Break them on the side walls of the bedside tables.

The manufacture of the box begins. It is also done from plywood 6 mm. Measure the size of the depth of the box and secure the details to each other. For this, the vehicle screws were used for which the holes were pre-drilled so that the plywood was not split.

The front part of the box, which is made of the furniture shield, is attached at the very end, after it will cover it with varnish and get the handles suitable for her.

Now the bedside table is done. It will be mounted on the sewage. To do this, small carnations are driven into the upper end parts of the side walls, approximately 2/3 of length. I will apply the lid and pressed on it. It turns out markup for holes. Remove them and with the help of the waders and glue, secure the lid. To ensure a faster bonding, put some cargo on the cover.

Now we go to the manufacture of the next item of the hallway, also the stands, but with another appearance and corresponding dimensions - 820x490x400 mm. Internal shelves each makes it like he likes. The location can be any. We bind over the sides of self-stakes. The upper part of the central partition is attached to the sewage. Doors cut down and loops are attached. Do not forget about the facial bar and drilled under the plinth.

Now the author moves to the manufacture of Penal, which will have dimensions - 2000x400x400 mm. Side, upper and lower parts are peeling. Everything is attached to the self-tapping screw, except for the facial plank. She, as in other cases, will be attached to the sewage. For strength, the design in the corners fasten the corners of their plywood. The shelves located in the penalty will lie on the holders made of rivets, which are slightly cut down the upper part. Doors are attached to 3 loops each.

A lattice stack made of boards. Try the transverse rail to be placed so that later it was possible to attach hooks for clothes. The design creates a bedside table, which the author made at the very beginning. In the top of the crate makes a shelf. Holders for her are made of barking boards. Everything is grouped. The whole design is covered in several layers of varnish. Mix hooks for clothes.

It is an individually case with the hallway, because it is her all see the first when they come to the apartment. And that is why you can try to do what you want with your own hands. It is enough to remember about the designers - often exclusive things they make themselves. It turns out no worse, and besides, absolutely unique. So why not try to furnish the hallway yourself?

When it comes to a speech about a homemade hallway, it is worth understanding that this is not only about sticking wallpaper without the help of specialists.

With your own hands you can create a lot:

• Furniture;
• Multi-level ceiling;
• Decor and accessories.

First of all, they independently perform the finish - it is the easiest. To the simplest variants of the finishes include staining and salaling with wallpaper. You can choose an interesting option: wallpaper with photo printing. Huge drawings in the hallway to nothing, but the original abstract pattern will be very close to the place.

Since the hallway, as a rule, is not too large, then the current color scheme is bright. This applies to furniture.

You can use warm contrasting shades to highlight individual parts of the room or furniture items themselves. Decor can also be made independently. The original upholstery of the Banquette, painted or dressed in knitted covers of pots with flowers, a mirror, which is decorated with seashells or artificial flowers, and, of course, braided mats at the door - all this is very easy to do, does not require large investments and brings pleasure in the manufacturing process.

How to make a corridor in the house if you do not want to mess with an independent assembly of furniture at all, especially if there are already furniture in the hallway? No wonder they say that changes can completely change the perception of the room. This also applies to the hallway - it is not necessary to purchase new furniture if some techniques can be applied.

For example:

• Permutation;
• Accessories;
• Change color.

Main reception - rearrangement of furniture. For example, from the cabinet you can refuse at all, and replace it with vintage hooks on the wall and the original hat. At the door, the place will take a large plant in a pot, and nearby you can put a shoe. If it is strong enough, then you can arrange the seat on top, then it will be possible to sit on it and comfortably go.

For the hallway, the mirror is absolutely necessary and, preferably, large. You can revive the mirror using a rim decoration. And if it is built into the closet, you can use various stickers. Among the most popular - floral patterns and imitation of the window.

The furniture itself can be repainted in a suitable color style. And wooden furniture can be covered with color varnish to emphasize the texture of the tree, or artificially agrees.

Ideas how to originally make a hallway with your own hands

Modern apartments or private houses most often have more spacious dimensions in which an acceptable set of furniture can be placed. You can even put a small sofa with leather upholstery - such furniture is easy to wash and clean.

But, if the hallway is still small, you can pay attention to other techniques:

• Modular furniture;
• Narrow structures;
• Using walls instead of cabinets.

Modular furniture allows you to easily rearrange and combine all objects at your discretion. Very helps the angular cabinet with the mezzanine - there will be a lot of things there.

There are also narrow options for a set of furniture. If it is not critical for the couch or hangers, then for storing shoes or a cabinet, such a design will not fit - too little space.

And finally, the walls themselves. You can place hooks and fabric organizers for shoes and accessories on them.

Examples, how to furnish the hallway in the apartment: photo

Since the hallway is a place where the most dirt and dust is inevitably, then the materials need to be chosen with the calculation so that it can be easily soaked. Some people bright shades seem not too interesting, and therefore designers are advised to dilute them with bright shades.

Namely:

• In accessories;
• In the upholstery of furniture;
• In the allocation of some parts of the interior.

Very often the entrance door is painted with bright color - the interior then looks bright and alive. But the main accents are located in accessories - bright vases, textiles, figurines, clock. This list can be continued for a very long time, most importantly, do not overload the hallways by these parts.

A very important role is played by the upholstery of furniture, if it comes to a pair of chairs and a junction. Material can choose absolutely any. The only thing that does not tolerate the hallway is carpets and carpeting surfaces.

How to equip the hallway in the apartment: photos and examples

It is worth returning to the furniture. Proper arrangement plays a very large role.

To do this, know several rules:

• Do not clutch the space at the door;
• The wardrobe is better removed deep into the room;
• Instead of the cabinet, you can use closed-type junction;
• Corner furniture saves space.

Most furniture items for the hallway are easy to make them. To begin with, it is worth deciding with the materials.

The championship is kept, of course, wooden configurations. They are strong enough, do not deteriorate, look aesthetically, and they can be easily repainted and decorated.

Furniture made of wood is not so easy to purchase, because it stands very and very expensive. Another thing is specialized furniture shields, as well as sheets of chipboard. The first is also not too cheap, and it is not easy to find them, but the second meets often and are acceptable.

Of the additional tools you will need:

• Loops and corners.
• Roulette and pencil.
• Screws for furniture.
• A sharp knife.
• Sandpaper.
• Lobzik or saw.
• Screwdriver or screwdriver.
• Finishing materials, if needed.

Non-standard entrance hall with your own hands: drawings and schemes

It is necessary to start work itself with simple couch. It is necessary to determine the height, and cut the 2 identical sidewalls from the shield on this height. If there is a plinth, then on one side, a small angle is spiltped. From above you need to do the same thing so that the lid is already. Then copold the sidewalls with two bases, and the lower should not be at the floor, but above, then the gap can be masked by a dust. The rear panel can be made of plywood.

The door should be such a box in the box. Make holes, and attach the door loop. From plywood to make a crawler for a box. From plywood to make the bottom, and the front should be slightly larger. Cut the cover and put on glue. Box copper with self-drawing.

Furniture manufacturing will require:

• Reiki;
• Plywood;
• Pens;
• Woodwoods.

The tube with two doors is done otherwise. It is necessary to assemble a box of four bases, not lower than a single door. Credit with self-drawing. Inside to make a crawler for boxes and fastening for shelves at will. The rear panel should be plywood. Put the doors and attach loop. Both covers are copped by the wrenches.

For the cabinet you need 2 large sidewalls. To chop them, base (top) and central shelf. Cut 2 identical doors. Attach to the closet. The rear wall is also made from plywood. Inside, lay the boxes and shelves at will.

Repair of the hallway with your own hands (video)

To cut down a few identical boards for the hanger and make a horizontal rack. Top over the entire width to attach the shelf for the hats. Attach the hooks and hang on the tapping screw on the wall. All covered with varnish and decorate at will. Dare!

Hall to your own hands

Sometimes the choice in stores simply kills the monotony of its products. Most of the owners of houses and apartments know that it is not so easy to choose furniture for an entrance hall. If the room is small, then the cabinets simply will not be able to fit, or fill all the space in it. But those people who own spacious hallways may fall into a difficult situation, because the models that are on sale do not always fit into the overall interior of the spacious room.

If you do not have the opportunity to choose a suitable closet, then you should not be upset, and you should think about making perfect furniture for your home and you will have an entrance hall with your own hands. Such an approach helps to save finances, and get furniture, which in all its parameters you fully arrange.

Is a beginner master able to cope with such a task? Of course, yes, the main thing is to have the desire and all the necessary tools, as well as materials that will definitely lead only to a good result. It is clear that the masters who do not have experience is better to choose the models easier. But the masters who are not first engaged in the manufacture of furniture can be made of the models more complicated.

In order to facilitate your work, we have prepared interesting materials.

How is the hallway do it yourself

Hall to your own hands

From the very beginning you should determine which model you wish with its size. If we talk about a small room, then it is not necessary to overload it with a large number of furniture, you should apply standard furniture for the hallway, where there is a small compartment for outerwear, for shoes and other necessary things.

If the hallway is spacious, then it can be put in it a large wardrobe. When it allows the area of \u200b\u200bthe room, then such a wardrobe can become a real dressing room, which every woman dreams of. The cost of incarnation of such a project will be more.

You can also consider options that will be a compromise between external appearance and capacity. But it is necessary to remember that the big depth will allow you to put a lot of things there.

Visible model you need to start shooting measurements and start calculations. You should also make sure that you have the entire tool that is needed for this.

What tools and materials you need

Tools should be prepared in advance:

• electrolzik or Pillet;
• shurapovern;
• sandpaper;
• construction knife;
• screws for furniture;
• corners;
• roulette;
• loops.

In addition, the material will also be needed in order to make a hallway. Experts recommend using furniture shields, as they are produced from natural materials without the use of synthetics. This kind of shield is completely safe for health. But it has a very high cost.

LDSP uses much popularity. The fastener resin is added to the material, which may adversely affect people's health, if laminated slabs will not be closed in edges. But this material has a small cost and excellent characteristics, as well as it is very easy to work with it.

Standard entrance hall with your own hands

In order to make a simple hallway, you need to purchase such materials:

• 12 pcs loops;
• shields for furniture 7 pieces, size 1600 per 400 per 18 mm;
• plywood 6 mm thick;
• type 2 stuff boards, 2000 by 240 per 18 mm;
• handles for furniture 6 pieces;
• three-dimensional slats with 3000 sizes 40 to 12.

Specialists advise starting with Penal. It has a size of 2000 by 400 per 400 mm. From this shield it is necessary to cut the desired planks, and the top cover with the calculation of the oversta. You still need two shelves. The assembly is very simple. Planks should be placed in parallel and secure with the help of the lid and screws, and install the shelves. In order to ensure in the corners, the framework of the frame should be fixed using the corners that are cut from plywood.

Since the doors are located alone under the other, it will be easier to install than one, so that this option will be more appropriate. From the shield cut the door of the same size and a few shelves, how much you wish. Doors need to be fixed on the loop. You can use two hotels for each door, but it will be better to fix them to three.

The size of one bedside table is 400 per 400 per 820, and the second will be 820 per 400 per 490 mm dimensions. You can not do one of them, and it will not damage the overall design.

In order to collect the first bedside table, you will need 2 identical side parts and a shelf that will serve for the entire design below. A part from above in the tube will be narrowed, so that the lid should have smaller sizes compared to the main part. All these parts are fastening with the help of self-sufficiency. If you wish, you can use the furniture waders. Do not forget that you need to make a hole drill in advance and at the same time use glue.

From the shield it is also necessary to cut the doors for the bedside table, they should be fixed with two loops. For a drawer, it is necessary for a slide. It is recommended to purchase them in special stores. But you can also make them yourself from plywood, but in then the boxes will be pulled out, and this complicates the use.

The second tube is made very simple. You only need two side parts and two shelves that will help to form a frame. Inside you can fill the tumba than you like. All items are fixed using self-tapping screws or waders.

After all manufactured processes, it is necessary to collect a hallway. All items must be copped, and then cook the boards. They should be beautifully located from one edge of the foam to the edges of the couch, thus, the base is created for the hanger. When attaching boards, it is necessary to withstand the same step when the boards are fixed on the wrong side of the bedside tables. In order, the design at the top was more durable, the boards should be made using a rail. It is necessary to have it at such a height so that then you can attach hooks on the rail so that you can hang up the outerwear. If you wish, you can additionally make a shelf for hats.

Do not forget to cover all the hallmarks of varnish, fasten the hooks and handles.

Wardrobe Coupe How to make your own hands

Make a wardrobe wardrobe much easier than you may seem initially. But it will be better to first decide on this value. Such a product as a wardrobe assumes an interesting design of the door, because they move along the clouds parallel to the cabinet itself. It can be made both built-in and standing separately.

If you wish, the case of the cabinet can be made of drywall and so hide it in Fallast. But let's look at the usual scheme for the production of a wardrobe, which has walls on the sides.

Cup model

The model we consider has 2020 to 625 to 2320 and has several main parts:

• racks on the sides should have a height of 2288 by 625 mm (in these calculations, the thickness of the leaf of the lower and upper planks is taken, which is 32 mm);
• in addition, the upper and lower bar can be considered large details: 202 by 625 mm;
• vertical racks in the middle are inextricably associated with a barbell for things. Usually, it is fixed to a height of 1900 mm, so the standard dimensions for them are so width 525 mm, and an altitude of 1900 mm. Those 10 cm, which remained necessary for the proper operation of the door of the sliding type.

Cabinet filling

Fill the wardrobe you can like you more. It all depends here only on what you want and prefer, but it should be remembered that the location of the fastener system should remain.

Any details will be better ordered in carpentry workshops. After all, to cut off home all the necessary elements do not always get exactly and beautiful, even if you have such an experience.

Assembly

assembly

Only after that you can start the cabinet assembly. For the assembly it is recommended to use not only the wrenches and screws, but also corners for furniture. Rails should be installed inside the cabinet on a special area, which should be separated in advance, that is, those 10 cm that you left during the preparation of blanks. Now you can install the door and use the wardrobe.

Hallway hallway personnel

The complexity that occurs during the manufacture of the hallway of the angular type is that it is necessary to make careful and competent calculations, even a small error will cost you a large sheet of materials. Initially, it is necessary to shoot the measurements and check the walls. If the walls have an uneven surface, you will have to do a common framework. Otherwise, the walls can become the basis of you, and the shelves can be attached to them. This option can be called more economical and simple, but we will consider a separate wardrobe, as ideal and even walls in the house or apartment can be found quite rarely.

Choosing a drawing

Initially, you should choose the appropriate drawing to you, while it is worth relying on the room, the length of the walls and their location in relation to the doorway. It is also worth thinking about the equipment of the cabinet inside.

Main elements

According to your chosen size, it is necessary to make 6 main parts of the case:

planks bottom and upper;

walls back 2 pieces;

the walls on the sides, of course you can make a closet without them, but it will become less functional.

Cabinet assembly

Assembling an angular hallway

After you collect the frame, you can start the installation of shelves inside it, as well as drawers and baskets and hang hooks and rods.

Hall-type hallway you can equip the doors on the rollers, thus making an angular wardrobe. But the usual swing doors are perfect.