So, having understood how the chandelier should be arranged correctly, we carry out its main lighting and at the same time decorative elements: lampshade and ceiling. Reflectors are technologically easier; Their manufacture and fastening to the carrier design chandelier of difficulties does not cause.

The Internet is full of pictures with really very beautiful homemade luminaires. However, considering them check out the question: how to replace the light bulb? The answer is not always located in the original sources. Methods for fastening the lighting elements in lamps that allow the replacement of the lamp without the use of the tool will be considered in the following article, but described later in this technological methods are calculated on the fact that the lampshade in this case or shifts up, or is removed down, or it can be easily climbed hand.

Materials

In the order of increasing complexity (and longevity), the products of lampshar and ceiling, with their own hands at home, can be made of paper, plastics, threads, ready-made tubes of various kinds, twine or yarn, frame with fabric cover and stained glass. The last 2 are quite complex, but with a skillful approach to work on lighting and decorative qualities can exceed expensive purchased.

Make paper lampshade is easiest: From materials, except paper, you will need threads and PVA glue, and from the tool - a sewing needle, scissors and, possibly, a sharp mounting knife. However, paper lampshades are fragile and therefore suitable mainly for chandeliers. But the ruined lamp shade is easy to replace new.

Make a paper lamp is somewhat stronger in various ways. The simplest is to dial the glue-ball strip ball, glueing them on the poles and among themselves, pos. 1 in fig. However, the design in this case is uniform: sufficient strength of the product is provided only and only its spherical shape.

Elements of paper lamps

Another way is to strengthen the paper itself. It will require a little additional material: a copper enamel winding wire with a diameter of 0.25-0.4 mm or thread. In the first case, the lampshade will be used without additional hardening and for the lamp, and in the second for overhead decorative elements it will take a solid bearing basis, for example. From a plastic bottle. Strengthens paper for lampshar with wire as follows:

• On a sheet with a density of 90-140 g / sq. See details outlines.
• Sufficiently sharpened pencil, or mechanical with a 0.6 mm rod, rigid mesh lines. If the lampshade is glued from several one-piece or a little cropped sheets, the grid lines should form a seamless pattern.
• Tassel glue PVA thin layer.
• When the adhesive will dry up to turn, applied along the vein grid - rigidity ribs - from wire.
• Lubricate the top of the leaf with a density of 35-60 g / kV. cm, impose on the first and carefully smoothed with your fingers.
• A day later, the parts are cut with scissors, glue together and paint. In this way, you can even make imitation of wings of rare types of butterflies, pos. 2; In this case, Mahaon Maiac.

When using threads, both sheets take a density of up to 60 g / sq. See, then, it is said, the bearing basis will need, but it is possible to imitate even the texture of rose petals, pos. 3.

Note: Paper lampshade, durable "almost like real" can be made from papier-mache. Technology, enough, time-consuming, is described further, see the downtown for the kitchen.

Plastics

It is elementary to make a lampshade for chandelier of disposable plastic cups bonded by a stapler, see fig. Its lighting qualities are very good, but the view is frankly utilitated. Therefore, such lampshairs make sense to apply indoors with fairly high requirements for lighting quality, but not frontal. The radiation diagram (DN) lamp shade from cups forms cardioid.

Label lampshade

Plastic spoons lampshade

Ferric DNs with a wide open, very mild light in the central spot and uniform illumination in the side zone, allows you to achieve a lamp with a lamp lamp (or pineapple?) From blurred plastic spoons based on a bottle of PET with a cropped donkey, see fig. Effective light mitigation is achieved by the fact that spoons work as translucent cup-shaped reflectors. They are glued to the bottle and glue with a silicone, assembly or adhesive gun glue. Cyanoacrylate glue is also suitable, but it needs to be taking thick. The cheap "superclauses" is very tech, the droplets will vomit everywhere and will reverse the glossy surfaces of spoons.

From the same bottles, too, you can do good lagging lamps. For example, the sphere from their bottoms, bonded by the stapler, as well as stopper cups (mini-master class, see fig.) Dast cardioids; True, compared to the "tired" noticeably distorted. But in the country or in the utility premises, the chandelier from the bottoms will be quite useful.

Abazhur from Dyshek Bottles

Abazhur-hedge of plastic bottles

Romantic soft light, a little spotted, but within the limits of allowed, will give a ceiling ball from bottled "hedges"; True, they are more like blossomed marine anemones - Actinia, see the photo on the right. It is easy for "hedgehogs": the bottoms are cut off the bottles, the side walls are cut to the scar before narrowing in the neck, the strips are wrapped on the neck, glued with droplets of glue and fixed with threads or scotch. However, a transparent spherical basis will need a transparent spherical foundation for the assembly of "hedges". It is obtained similarly to the lampshade from the threads (see below), only the threads take white kapron or propylene not the thicker of the 20th room, but instead of PVA - a colorless acrylic lacquer on a water basis.

Very uniform illumination allows you to achieve, and very decorative, lambs of leaves cut from bottles, see fig. The assembly of it leads on a temporary spherical mandrel, see below.

Homemade plastic leaves lampshade

A step-by-step master class in this case is also low, but requires patience, accuracy, some additional tool and, possibly, material:

• We are preparing a soldering iron with a bronze nickel-plated sting (for dry soldering) by 40 W or with ordinary copper 25 W;
• If the sting is copper, there is still a Teflon (fluoroplastic) tape 0.06 mm 60-80 mm wide;
• Cut from bottle leaves. From the point of view of lighting, pale green or light brown is better fit;
• Powering the soldering iron (copper - through the film) slightly melt the edge of the leaves, otherwise they will look unfulstly;
• The tip of the sting (copper also through the film) "Draed" the veins;
• The plane of the sting between the veins with light touch slightly we bore the surface to be like real leaves, not quite smooth;
• Again the tip of cumulating deeper, but not the priest, we derive the central veil. It is convenient to do this on a soft heat-resistant subdum (there will be a hawk or felt in several layers);
• We put into the central vest of thread and we write the "vesting" side roller on the hollow;
• Complex leaves, if required, form, binding the thread of leaves;
• Declaring the leaves on the film (now anyone), we impregnate threads with acrylic varnish from the pipette. Upon its drying, foliage is ready for the assembly.

The procedure for manufacturing Christmas decorations and luminaires from threads is described in RuNet many times. For example - video:

Video: Shashore from twine / threads do it yourself

Here you can only note that, firstly, the threads on the laid-sized lampshade will need at least 100 m. Secondly, it makes no sense as the mandrels of inflatable balls: after 10-20 turns under the pressure of the stretched threads, the ball is pronounced. And in the end it turns out something uncomfortable. Thirdly, it is not necessary to soak threads in a flour ceased in advance: the product will be fragile and not moisture-resistant.

As a mandrel in the manufacture of lampshar made of threads, it is best to use a tight inflated camera from a sports ball or durable, inflated from the pump through the nipple, a silicone beach. The mandrel is lubricated several times with Vaseline (Lanolin), thoroughly rubbing it with his hands. The ball does not hurt; On the contrary, it will extend his life.

Device for making lampshar of threads

Next, the thread on the mandrel is wound, continuously stretching through the simplest device, see fig. This mini is an impregnating bath, so that he did not accidentally crawl, did not overturn and did not pour something glue, they fasten the tape on the table; Comfortable double-sided. The cup is first pushing the needle with a thread, then pouring PVA or acrylic varnish and shake, tightening as needed. Usually the thread goes through the bath itself, because Glue, until dry - good lubricant.

When winding, do not forget to leave the window for entering the cable and the cartridge - the strength of the cutting thread sharply falls! A day later, at its end, they produce air from the mandrel and pull it out through the same window. To threads, she, "favored", is glued very rarely and irrelevant: it is possible to tear off, slightly pulling or giving the finger, and the product remains safe.

Note: Instead of threads, you can use jute, sisal or propylene twine, but in the lampshar there is better use, see below.

And where is it all?

Plafones-balls, see fig., Suitable in the nursery, because Form smooth soft light. The one that on the left, from paper wrappers for cupcakes - based on the filament ball. Threads - propylene or subtle categorous colorless; Binding - acrylic varnish. White in the coil, after impregnation with varnish such threads become almost transparent. Shade ball from cups (right) is not so interesting, because The sudinki is all the same, but also to refine it harder.

Lamp chairs for children

In the hallway, the lampsphere from the same cups is suitable, see fig. on right. With a small power of the lamp (more precisely, its light stream) will give a bright spot below and an acceptable illumination of the rest of the room, so you can use a little burning incandescent bulbs by 15-30 W. The fact is that the resource of lamps and LEDs with frequent turning / off is sharply reduced. And the low-power incandescent lamp, especially in the hallway, where the light is constantly not lit, the cost of electricity will not significantly increase.

Label chandeliers in the hallway

Special case - kitchen. Requirements for lighting in it are set out in the previous article. But the lampshade in the kitchen quickly gets dirty, and soot eats hard. Recall: Bright light contributes to condensation and bituminization of the vapor of organic compounds. This is the deposition of soot; The lamp is also covered in brighter.

The simplest way out is disposable paper lampshade. "Cryer", as for pos. 1 Fig. Below, it will make the nature of the lighting just necessary in the kitchen, but it will have to re-attend it quite often. It is better to define on a suitable mandrel launcher from Papier-Masha, pos. 2. After the varnishing of acrylic varnish, it can be carefully soaked with a rag with washing for dishes, and painted with a blacksmithing patina, it will be similar to a wrought handmade and no one there are old newspapers.

Lamps for kitchen lamps

But the lampshade on the pos. 3 - straws for juice glued to the bottle - an example of an unsuccessful solution. The light of such a lampshade will give the ideal for the kitchen (the straws work partly and both light guards), but it is blocked quickly, you will not be patched as it should not, and the product is time consuming. Plastic reflectors of kitchen lamps of local illumination is better made from multi-precision plastic dishes, pos. 4, it is quite a rack, inexpensive and easy to clean. Cups with handles and saucers, of course, the case of a designer solution, but the piles are without a picture - what is needed.

How to make papier-mache?

Papier-Masha material useful for many purposes, so we recall the technology of its preparation and application:

• Old newspapers, or, better, the most cheap disorder paper tongs on the nails about the nail of the thumb. Paper will need a lot!
• Scraps to the top fill the appropriate dishes; Let's say a liter glass jar.
• In the cool boiling water, 1 / 3-1 / 5 is divorced by the volume of PVA.
• While the solution is not cooled, poured the paper mass.
• It is stirred while the paper does not completely spread to fibers.
• On the cooler of the papier-mâché is overflowing into consumables or immediately allowed. Store paper paste you can up to 6 months. In the refrigerator in tightly closed dishes.
• Prepare the following portion.
• If the paper paste immediately goes into the case, the next thing can be added to the rolled piece of mandrel until the previous one is still wet and thumb. If you fly in dry, the product, dried, can break down on the "pellets".
• To varnishing, painting, etc. Preparation is ready after weekly drying at a temperature not lower than 22 degrees. The air temperature around the workpiece should be the same on all sides! Sew on the battery, convector, under the right sunlight or infrared emitter can not be!

Tubes

The lamps and plaffers made of cuts of the tubes most often for night lines and lamps in the bedroom: as a result of the round section, there is always a significant refraction of light, which can be very intimate-romantic, but for constant and working lights in most cases undesirable. Pretty spotted light gives labels from translucent tubes, see rice; If you use the segments of a thin transparent PVC hose, then the game of light will turn out very beautiful, but it is not necessary to look at it for a long time and all the more read or sew with such a light.

Lampshade from the tubes

Paper and other fibrous materials light refit for little, but the tubes of them themselves are fragile. For example, the lamp shade from newspaper tubes is better to do on the frame, see below: just because they are easily embarrassed, thin paper tubes are excellent material for weaving. As for lighting properties, then the paper, especially clean, they are excellent.

Shador on the frame

Now proceed to lampshaps that are suitable anywhere, incl. And for a table lamp, which elbow can shove on the floor. In addition, we will put the condition so that the lamp to the lamp can be washed, cleaned, change at will. Therefore, glass or solid hard plastic lampshades do not touch; They also can not be done at home. Those., Engage in lampshades on a skeleton frame.

About lampshade tissues

The decorative light case of the lamp is preferably sewing from a tissue with darous threads, i.e. Natural. Due to the diffraction on smooth threads of synthetics, the light penetrating through such a lampshade can be tough. Choose a cloth for lampshar on-eye is easy: through the sample, swing it smoothly, look at some compact bright light source; Preferably LED, because It gives the most coherent, i.e. Ordered, light. The criterion of choice is simple: the less observed at different angles of view of the moar stripes, the fabric is better.

On the restoration of aboara

The lamp shade is pretty laborious and complicated technologically, so first it is necessary to look at the farm: whether the lampshade from the old lamp did not break down anywhere. Stop it, repair and update the lamp to the new case will be easier than to make a frame from scratch.

Homemade tool for measuring large diameters

The detected "basket" may be very cleaning form, and to build grids (see below), it will be necessary to measure its diameters in several places. In this case, the self-made caliper from 3-wooden plates and pairs of drawing apartments will help. It, of course, will not give, but reachable (+/- 1 mm) for crude-sewing work is enough. And the idea of \u200b\u200bthe possibilities of such a tool gives rice.

Measurement procedure 2-speed: on sponges in touch places they make a pencil mark, and then remove the size between tape measure. So that the moving sponge slid more smaller, and, accordingly, the measurement was more accurate, under the holding of its gums you need to put the fluoroplastic film. To measure the small diameters of the sponge roll over with coats outwards.

Building pattern

Now remove the necessary diameters: lower and upper hoops (D1 and D11 in pos. 1 in Fig.), The largest and smallest on the belts (D2, D6, D10), in the locations of the beggars, i.e. Where the curvature of the forming changes the sign (D4, D8) and on the breaks (D5). Others take more or less evenly between mandatory.

Building the pattern of lampshar

Pictures of 6 wedges will, taking into account tightening of the fabric, are equal to half the measured diameters (pos. 2). If the wedges of the finished sleeves are supposed to be more or less, proportionally change the share of the diameter in the corresponding diameter of the pattern. But it is too early to cut and sew.

In the same place for pos. 2 It can be seen that the crosslock is geometrically not completely similar to the template. In the node I (breaking inside), these are still Polbies: you can put a silent-scene and tighten the seam with a cord. If the lamp decor suggests Ryushi, ruffles, festers, etc., then it may be necessary: \u200b\u200bsmall folds will come to the place, and in the breakthrough circuit, the cord will not be visible.

However, on the circuit shelf (node \u200b\u200bII), if neither twist, but give the allowance so that the seam does not leave, it is not possible. In the highest geometry, it is proved why, but we don't need to climb into these debursions: we simply cut the paper template for "capricious" diameters on the breaks and shelves (pos. 3).

Sewing Czech

Now, like on our patterns to sew a lampshade? First sew individual parts of the sleeve; In this case, the bottom, middle and top. Then to the widest belt (bottom) are sewn the largest part in the width (here - the middle). Next, in the same way, stroke 2 following the width of the part, etc. The bottom line is that the shortest transverse seam (we have 2) stacked last. In this sample, after stitching, niza with the middle to sew the top. It is completed by sewing the cover of the trimming of excess points, except for the lower and upper socios. Edges necessarily handle.

Cracked tightness

The next stage is landing the case on the frame. Here, the machine can be sent to the chulad: the work is exceptionally hand. Phasepno tight carcass of the lampshar case is made like this:

• The case turns out (he sewed from the inside, probably, and so understandable) and put on the frame;
• Wrapped inside and flash upper laps;
• Tighten and hang fabric to the first inflection (here - D8). If in the initial sample there was no hoop here, it must be put in advance, see below;
• Take the fabric to the ribs of the frame from above alternately, and to the hoop on the inflection;
• Repeat PP. 3 and 4 before the next inflection (now D5), and so to the lower hoop;
• Wrap and flash the lower marrow.

How the simplest frame of the lamp lamp or a lamp is arranged, can be seen on the pos. 1 Fig. Suspended for chandelier is distinguished by the fact that the ring will be at the top, the stretch marks will go to the upper hoop, and then additional holes are needed to fasten the suspension.

Device carcass lampshar

The ring is cut out of a well-soldered and sufficiently durable sheet metal (bronze, brass, galvanized steel with a thickness of 0.4-2 mm) or durable plastic from 1 mm. A computer disk is suitable, under the E10 cartridge, it will only need to drill holes for stretching and fastening. The main dimensions of the ring under the E27 cartridge with the fastening of the catching nuts (pos. 3) are given on the pos. 2. But to make a ring for fastening into the gap between the case and the cartridge clamp with the skirt (pos. 4), is unacceptable! Such cartridges are attached only by a threaded fitting in the lid!

How are attached to the row of stretching, shown on the pos. 5: Their billets bend the crochet not to the end are injected into the mounting holes and carefully live in passage. Then, if the ring is metallic, pecks (see below). If the plastic is fixed with droplets of superclaud or silicone.

Build on soldering

Frame details make from plastic steel wire with a diameter of 1.5-2 mm or cycling spokes. The latter is much stronger, do not rust and do not require painting, but they need to be bend carefully and they are worse. For soldering, the carcass will need:

• Soldering iron at least 65 W (better than 100-150 W).
• 6% solution of orthophosphoric acid. Sold, for soldering, in radio logs and construction. Orthophosphoric acid is also available as a dietary supplement E338 in the form of needle colorless hygroscopic crystals.
• Flux paste (gel for soldering), be sure to be brown.
• Thin, 0.15-0.35 mm, copper naked wire. You can take vendors from the electric pipe.
• Solder Pos-30 or Pos-40. They are refractory (therefore, you need a powerful soldering iron), but there is a lot of stronger Posh 61 and others. Legged.

Note: Orthophosphoric acid of medium power, highly toxic and / or caustic vapors does not exude. But still, when working with it you need to follow the precautions - wear safety glasses and gloves (domestic latex).

Key framework assembly procedures on soldering are shown in Fig.

Soldering of steel parts

Phased solder steel frame collected as follows:

• The ends of linear blanks are kept 3-4 min in acid (pos. 1), and then rolled in water (pos. 2). Waters need not less than 1 l, and after 4-5 flushing it must be changed.
• If the soldering is in the middle or detail bent, in acid soaked clean white rags and wrapping the soldering place it. They hold about half a minute, then the rags are rods in acid, turn the soldering place again, and so while the total exposure time for metal does not reach the same 3-4 min. After treatment with acid, the part in this case is washed under the jet of water for 1-2 minutes.
• Without touching the bare fingers of the processed places, the frame is fully assembled without missing: the places of mischief of the jack of tight, but not tight, i.e. With intervals between the turns of 1.5-2 mm, wrapped with copper wire, pos. 3 and 4, and apply 2-3 drops of flux pasta for each joint. Places of packs at the crossroads of parts are wrapped with 2-3 coils of copper wires and flush 1-2 drops.
• Semi-hum, i.e. Without a hanging drop of solder, the sketch of the soldering iron warms the places of the packs until the flux is spread over all the alkalis, pos. 5. Great to boiling flux and the appearance of vapors is not needed. Also the end result will be better if you warm the flux with a separate soldering iron with a dry bronze nickel-plated sting.
• They gain a drop of solder, put into place soldering (pos. 6) and warm until he lets everywhere, as before flux. At the bottom at the bottom of the surplus of the solder gently remove the sketch of the soldering iron. It is impossible to apply a flexible solder in the form of flexible wire, and refractory solders are produced mainly by rods.

Fabric or twine?

Propylene packaging twine and paper tubes have good lighting properties. If the lamp shade is to make wicker from the twine or from newspaper tubes, it will give a smooth soft light, and squeezed out-of-sowed-sewing work. But in the frame for a wicker lamp, first, at first, at least 10-12 ribs, evenly arranged around the circle.

Note: If the frame is a simple form, then carriers (steel) can only be 3-4 ribs. Let them be even straw, they are glued to the upper and lower hoops.

Secondly, to get rims at the top and bottom, acc. The training is either made twined in height, with a period of 2-3 cm, or the strips of fine metal or rigid plastic of the same width are attached to them. The rims are needed on decorative considerations: solidly wind by twine or tube, and if the rim is double, weaving can be used eight. The entire side surface is brazed as a basket.

Abazhur-stitched shop

Stained glass lampshades form light stream predominantly refractiveness, so more suitable for the living room.

stained glass lamps and ceiling

Stained-glass fragments are gaining from rhinestones, faceted or cabochon. The lampshade-stained glass window on the heat-resistant mandrel (eg steel bucket) on Tiffany technique. But compared to the stained glass window for the window or door here, since the connections of the elements are not solid, and point, there are significant differences:

• Solder is used only durable refractory, the same as for the lamp shade, like a flux with a drone.
• Framing of rhinestones before soldering are made only from a special copper foil - Folia - 3-15 mm wide, depending on the width of the rim of the crystal.
• The protective film with folia is removed immediately before applying it on the crystal; It is impossible to touch the outer (soldered) surface of the folia.
• Also, it is also impossible to postpone the soldering of wrapped foley rhinestones on tomorrow: copper will have time to oxidize, and the connections will turn out to be fragile.
• Upon completion of the soldering and thorough cleaning of flux residues (rags with alcohol; then - distilled water) rations are messed up, having a thick-blue solution of copper sulfate.
• The residues of the vitriol are flushed under the jet of water. Tassel or even cotton crashes, because The copper film on the solder is very thin.

A small surprise - about New Year chandeliers and lampshades

Soon the new year, it's time to make christmas toys and festive decorations. And - New Year's chandelier. Lastra? Yes. Remember how the festive mood falls if the top light is included in the room with a Christmas tree. What no, but the New Year's lighting should correspond to the spirit of the holiday. Lighting equipment will postpone the days of serious, in a few evenings nothing from festive light will not happen to us. The case, it is time, but also fun hour.

New Year chandeliers

Usually a New Year chandelier - attached to the chandelier in the living room Christmas wreath with light bulbs woven into it. But it would not be necessary to engage in electric mounted work at the height in the pre-holiday turmoil. And what if the Christmas tree in the nursery, where is the chandelier paper? Then you can at least buy inexpensive plastic blanks for the Christmas balls, the garland with colorless light bulbs, to hove them into the balls, and hang such a heap (on the left in Fig.) It is more convenient.

If the design "everyday" chandelier is suitable, you can screw the candles lamps into it and decorate the same balls or, for example, painted with bumps, right there. And you can try a little and make the New Year's Lastra-Jasmine with your own hands, as in the video below. New Year is the new year, which is not talking.

Original lamps and lampshades do it yourself. Ideas, master classes

Lamps and lampshades do it yourself. Ideas, master classes

Hello everyone!

Creating or decoking lamps and lampshells The occupation is not only incredibly interesting, but also enough useful: it allows not only to create a unique subject, and in full compliance with the interior of your home, but also to save. It is enough to purchase the easiest lamp for little money and beat it to your taste. And there are options that and how to make a huge set, in a variety of techniques, using a wide variety of materials.

I picked up for us with you the idea of \u200b\u200bcreating and decorating lamps, I hope you can choose the appropriate option for yourself :) Pleasant viewing!

A lampshade decorated using decoupage technique, the base of the lamp is made of books

Decor of the metal frame of lampshar with feathers - very stylish :)

It is often enough to decorate the lampshades, fabric or paper flowers are used, the result is very romantic :)

Fabric flowers with candle processed

Cutting convolutions are used as colors

Flowers from twisted fabric

Ready Flowers used here

The flower is made of a stem strip of fabric, striking on one side and assembled in a bud

Spiral roses from newspapers

The bottom of the lamp is decorated with spiral paper roses

Decor of Ikeaevsky lampsome paper flowers

Lace and knitted napkins look very beautiful

The form attached with glue

The ball is inflated and the lace napkins are applied with the help of adhesive. After drying, the ball skeins, blown away and removed.

Very beautiful option: As the base of the lamp, the bird cage is used, the lamp shade is decorated in the decoupage technique with an outdated.

Even an umbrella can be used for chandelier :)

Even Loskutka trimming fabrics will go into business: wrapped, knotted. This option will be remarkably fit into the design of the country house or children's room.

Buttons-buttons

For the manufacture of lamps, various glass containers are used very often and successfully use banks, bottles. Just below, I led the master class on the manufacture of such a lamp.

A bottle as the base of the lamp - the bottom is also given a similar master class.

It is a bit more complicated here - the hole is drilled down on the back side of the bottle, through which the cord is started.

The lamp is made of figured metal sheet

Origami technology is successfully used to create lamps.

On the base of lampshar glued fabric strips

Lampshade from various retro leaves

Abazhur from the basket - why not? :)

The second life of metallic coland

Unnecessary fork-spoons created a very interesting version of the chandelier :)

Very cute solution: a metal mesh and beat the poultry is stretched on the frame. I think for the children's room.

And now bird subjects :)

Abjeur painting acrylic paints

Shallow veneer lamp

The base of the lamp is placed by marine shells

Knitted lampshades - look very comfortable :)

Decor of amusing memorable photos and slides

Flowers on this lamp - this is the bottom of plastic bottles :)

Lampshades are planted with paper circles

Vegetable lampshade :) I think, still a flower is frying there :)

Shashore from Shornov

Decoupage technique also applied here

Very interesting solution - wire as an art object :)

Lampshade decorated with cloth strips

Branch lamp

A lampshade is decorated with crumpled compressed coffee filters (forms for cupcakes)

Glass vase lamp

Base of lampshar - unnecessary toy soldiers, short and painted aerosol paint

Creative lap fetra

Shade from balls for ping pong :)

Flower decor

And many more, many different ideas ...

Master class on the manufacture of lamp from can & broit caps from Tom & Brit (BestOfinteriors.com)

We break through the nail hole to create a hole

Insert the patron

Stain in one color

Screw the light bulb and insert into the jar

Lamp is ready :)

Paper Lights from Varrell.com Resource

We will need an image of the castle

Cut out, cutting the winds, glue

Inside place a point lamp on batteries

Chandelier from a rope from Sarah M. Dorsey (sarahmdorseydesigns.blogspot.com)

We will need a rope, MOD Podge glue (can be replaced by diluted PVA), ball

In order to create a wavy shape, Sarah used wooden slats. We lay out the shape, we laughing glue for fixation.

After drying, we lay out on the ball and scrolling abundantly glue

After drying, remove the lampshade from the ball and stain in the white aerosol paint - the Sarah has four layers

Very beautiful lampshade of grandma squares from the author of the resource aboutgoodness.com

We are tightening with lampshane cloth

Strip tissue bend in half along and twist in roll

Run slightly

We apply glue on the fold and glue to the base

Master class to create a base for lampshar from Kiri (ilikethatlamp.com)

Necessary components

Bottle carefully mine, disinfect and dry

Covered aerosol paint

Mounting process

,

That's so a bottle of Jein has turned into a base for lampshar :)

As you can see, a sufficient thing is simple and very interesting. Give the will of your fantasy, create and let your home be beautiful and cozy!

Well, for those who still prefer to buy ready-made lighting devices, I recommend to look into a specialized Internet-shop Lampa.ua. - where in a huge assortment are high-quality and stylish desktop lights, chandeliers, sconces, accessories, etc. From the best manufacturers and at very flexible pleasant prices :) By the way, this online store according to Google statistics is the most popular among Ukrainian buyers :) Use with pleasure!

I wish everyone good luck and excellent mood !!

Dream to add brightness to nursery or refresh your workplace in the house? Or maybe you are a lover of the East, from where came to us fashion for these so gentle things? Then, you are undoubtedly worth reading how to make a paper lamp with your own hands - unusual original things in a moment will add a magic droplet in any corner of the house!

We guarantee - your guests will ask for a long time where you bought this design lamp, and learning that you made it yourself, will ask you to tell you how to make a chandelier of paper with your own hands and its step-by-step instructions.

In this master class, we will show the whole four ways, how to make a paper lamp, see and choose the option suitable for you.

To create this gentle lamp, prepare:

• Colored paper of any color;
• PVA glue or adhesive pencil;
• Clips;
• Compass;
• Scissors;
• Fishing line;
• Colored yarn;
• LED lamp ( );
• Wire with switch.

Step-by-step instruction:

Step 1

• On a color sheet with a circulation, we draw a semi-rapid width of 1 cm wide.
• With each line, we increase the diameter of the semicircle.
• Note that the sheets will need quite a lot. After cut down the semicircular stripes and cut them into pieces of 2-5 cm.

Step 2.

• Fold and glue the resulting stripes, making one side more than another - it will make it easy to glue them among themselves in a dome-shaped form. After that, you can connect them glue pieces of five.
• Bear clusters with each other, strengthening them with clips until the glue dry. Cland until you get a circle, with a small hole under the lamp.

Of course, you can fantasize, and your lamp will be slightly different with us.

Step 3.

Now, while our glue finally dries, let's decorate and our wire. Take for this yarn of any liked colors and gently begin to rewind it with it. Try not to leave irregularities, winding yarn on the previous layer.

You can drop the drop of glue to the end of the yarn, in order to strengthen it.

Step 4.

Let's make a holder for the LED lamp. To do this, we will tying from three sides (it is desirable to evenly measure the distance) to our glued bands, while other ends - to a paper clip, which will pre-break to the type of triangle.

Everything! It remains only to put the lamp in the circle and fasten to the wire. You can hang such a lamp both separately and in compositions with, for example, .

Master Class No. 2: Chandelier of rice or parchment paper

We bring to your attention a new master class, in which you will teach you to make rice paper lamps. Nothing difficult, as it may seem at first glance, there is no in the manufacture, and you can connect to this exciting business of all households. The designer lamp is suitable for both children's and your bedroom.

Instead of rice paper, you can buy a roll of parchment paper for baking

So, to make the lamp you will need:

• Unnecessary lampshade;
• Thin wire;
• Several rollers of rice paper;
• Iron;
• Paper cutter;
• Sewing machine.

Independent manufacture

Step 1

Take an unnecessary lamp to you (you can buy inexpensive new) And remove everything from it, leaving only the base. If your lamp lamp is similar to ours - then add a wire in the middle, carefully fixing it.

Step 2.

1. Prepare parchment paper, winding rolls and cutting on about the same rectangles.
2. Follow the sheets of ironuntil they become absolutely smooth and smooth.
3. Fold each leaf of the accordion, measuring equal distance of the stripes, and cut the paper cutter for the same smooth circles.
4. Try to use the cutter carefully and don't leave a lot of paper - There will be many circles.

Step 3.

1. Couple with each other, stitching in the middle, all circles. Make equal connected circles along the length and start strengthening them in a circle of the lamp.
2. As soon as they go through the first round, go around the next, reducing the length every time.
3. Carefully strengthen your lamp in the right place, straightening all the threads.

Do not forget to use only LED lamps, to avoid fire.

This beautiful chandelier is the result of painstaking work, after which you will admire your work and for a long time to be proud of yourself. On our site you will find many more ways to diversify your home lighting, for example:

• can I. .
• , For fans of modernity.
• Or for eco-style lovers.

Also you can to discretion paint circles from rice paper in any shadeBased on the color gamut room. If you want to hang this lamp in the children's room, you can add, for example, glass angels on long golden threads - again, choose suitable accessories to different rooms, it will add heat and originality.

Attention: Do not forget that incandescent lamps are very heated by paper, which can lead to ignition. For paper lamps and lamps, use only LED lamps.

Master Class No. 3: Chandelier Origami Paper

This beautiful bright lamp and though reminds the ripened berry!

For its manufacture, take the following:

• 2 paper bags so that when gluing a half-party bag (preferably with an interesting printer);
• LED lamp (in no case of the incandescent lamp );
• Wire with switch;

Once you decide that workouts are no longer needed, proceed to the preparation of a paper bag. Remove the handles and cut the bottom from the bags and glue them so that it turns out one big paper bag.

Fold the resulting bag in half, and after folding the halves of the harmonica so that it turns out 16 of the same bend strips. After folding the two outdoor bands diagonally.

Follow the uncomply schemes, and you will get beautiful lamps for home decoration. Perhaps you will have to practice a little to be perfectly to add origami, but you will not regret, after all, origami is a whole world of a variety of interesting things created by your own hands. And your children will simply be admired by your skillful handles!

Master Class number 4: Corrugated paper lamp

To make an unusual lamp you will need:

• Paper corrugated 88 × 44cm;
• Line;
• Spoke;
• Glue;
• A thread;
• Cable;
• LED lamp ( in no case of the incandescent lamp ).

Step 1

• Using the line, mark the paper sheet at equal intervals and Fold the harmonica by markup.
• Helping yourself the needle, fold the folded sheet of paper diagonally first on the one hand, and then deploying, on the other side.
• Expand the sheet - you should get locked Double Sheet.

Step 2.

• Connect the marked lines according to the photo, it is desirable that the leaf is not strongly abandoned at this time - otherwise the appearance of the lamp will be touched.
• It remains only to connect the tip of the lamp between themselves so that it does not fall apart, and fasten the cable with the LED lamp.

Follow the security - do not use conventional incandescent lamps, they heat the paper strongly and it can catch fire.

Paper chandeliers

The most popular chandelier is the chandelier with butterflies. And such a love for this product is not simple:

• firstly It looks very elegant and expensive.
• And secondly Making is very simple, you can even attract a child.

Such an elegant lamp will be well combined with any style of interior, as well as it is appropriate in the living room or dining room and even in the children's room.

Manufacturing technique:

1. The old chandelier or frame from it is taken as the basis. If this is not, then you can take the usual metal or wooden rim. If there is no such thing - takes a thick wire and make 2-3 wowing yourself, so that it turns out a circle.
2. Cut the butterfly by template (butterflies pattern below)
3. We take a drop-down thread or a fishing line and kpripim on her butterflies. Fasteners can be two types: either permeate the butterflies or plant them on silicone glue. How comfortable one.

Butterfly pattern

In order to make a chandelier with butterflies, just take a pattern, scaling it to your size. It looks very nice if you make butterfly several sizes, for example, 3-4 diameters. With the help of a pencil, we apply a sketch on paper and cut out.

• Cut the best stationeryknife or manicure straight scissors without roundings.
• Better use paper more dense and which does not attract dust, for example, velvet structure. As you often need to vacuum such a chandelier

Also very beautiful the option is obtained if you make a ball from the wire, we take a barley suspension from the chandelier as a basis and placed with a glue gun of several butterflies with a glue gun.

Paper chandelier

As a basis for such chandeliers, a ready-made Chinese lamp ball from rice paper takes. Usually they cost very cheap to $ 1-2. But it is possible to decorate it as you can and paper tartolets, an unnecessary card, newspaper or sheets of old books. We publish several ideas on the chandelier decor paper.

Lamp for the new year of paper

Feed the idea for the new year - it is to use old lampshade and stripped on a thread of snowflakes of various shapes. Very spectacular and beautiful. Below are several photo ideas of such a decor to the new year.

To polish your skills, as well as replenish the collection of unusually beautiful lamps, look more ideas and. We are confident among them you will find a lot of those you will surely want to create!

2 estimates, average: 5,00 out of 5)

What could be more interesting and the original multifaceted lamp, which will be done with your own hands?! By itself, the lamp is an indispensable attribute in every home, but it must be different something else, isn't it?!

The idea of \u200b\u200binspiration, in order to build such beauty, may appear the most different paths. The main desire.

So, in order to take directly, to work, you will need:
PVA glue
Corrugated cardboard
Scissors
Cutter
Simple pencil
Rule
Normal light bulb

Once you have acquired everything you need for the manufacture of a multifaceted lamp, you can proceed directly to the work itself

From the cardboard it is necessary to start cutting the strips of the thickness, which you want. But pre-draw sketches with a pencil and ruler so that there are enough flat stripes.

Stripeds should be a lot to have enough for the frame of the lamp

Now, you can proceed to sticking. It is necessary to do it very carefully, in order not to grind glue. Take one strip and create a square, gluing one after another. The shape of the lamp you can come up with yourself. Squares to fasten each other in different ways.

It is important to remember that one layer should be less than the other.

So, it should work both the frame itself and the walls of your lamp.

After the frame is assembled. We need to make a steady base of the lamp and spend the light in our lamp.

For the manufacture of the base of the lamp, you need to prepare 3-4 squares. To do this cut the required number of strips and glue them with each other.

The resulting squares also should be punctured all together - it will be the base of the lamp

After that, it is worth conducting light. We will conduct in the base of the lamp.

To do this, you need to take the cartridge and circle its contour on the bar, which is actually to keep it.

Cut a hole on the outlined lines

It is necessary to glue the cartridge holder into the lamp.

That's all, the lamp is practically ready. Print the light bulb inside the frame is completely optional, because it will stay quite tight. The frame of the lamp can be painted in the color that is suitable for your interior.

Lamps from paper, like a hobby, came to us from China and called such lamps in those vintage times by Chinese lanterns. Such lamps are characterized by many more qualities that make their manufacture not only the fascinating hobby and the ability to communicate with children through joint thinking and design. Making such lamps can earn good money.

Do it yourself a beautiful paper lamp in MK

What qualities have lamps made of paper:

1. Unusual. The world has created such a huge amount of different design, type and directions to apply these lamps, which is not enough fantasy to even imagine them, especially to describe in one article.
2. These lamps create a scattered and slightly muted light, pumping romanticism and creating an atmosphere of mystery.
3. An extraordinary even exterior lightness and a variety of forms can give the design of the premises completely different shades. You can create them in almost all styles.
4. With a completely insignificant value of the source material (paper), prices of such lamps are mainly dependent on the quality and originality of the design work and the skills of designers.

On the appointment of paper lamps:

1. Made from paper lamps can themselves be both the basis and frame of a table lamp.
2. They can be a lampshade at pre-made framework or with the participation of some decorative elements as the basis. Such decorative elements may be already serving their old things with the enezoles and attics
3. These lamps do not look badly on the walls, performing the functions of the sconce.
4. A ceiling lamp (chandelier) can look very elegantly, both with one light bulb and with more of their number.
5. And finally, the lamps from the paper, with whom the closer acquaintance began with this direction in the home needlework, these are lanterns. Among them are Chinese lanterns.

The simplest to make a paper lamp using pre-prepared patterns, of which the entire design of the lamp is assembled according to the scheme.

The paper itself was first made in China and precisely from there in the form of Chinese lanterns and began to spread the art of creating unique paper lamps as a style.

Today, this is this style, many prefer, making paper lamps. It is he who allows you to make revived paints, brightness and festive mood.

What materials do you need:

1. Paper. Normal, offset, corrugated, glossy, different colors. Paper must be translucent, white or color.
2. Electric cartridge with wire and plug. Remove from the old lighting device, if not, purchasing in the store or on the market.
3. Electric lamp. Due to the fact that the paper lamp can easily light up - choose a LED light bulb.

Instruments:

Stationery or just a sharp knife, pencil, ruler, thread and awl.

Production and assembly of the lamp:

1. On the back of the paper, there are contours and create a pattern of the lamp. To make it properly using the scheme, by which and draw the contour using a pencil and a ruler.
2. According to the outlined contours, bend the paper to where the harmonica is necessary, it turned out. It is impossible to hurry here. The quality of the flashlight and its appearance depends on how many black and smooth bends.
3. Insert the light bulb into the cartridge.
4. We make holes at the bottom of the cartridge with a selection and through them they drag the thread.
5. The resulting lampshade turn around the cartridge, glue the edges or simply impose them on each other. The latter will allow changing the light bulbs without damaging the lamp.

The most difficult thing in this process appear precisely when folding the paper base of the lamp. To give the lamp more originality, you can paint in some drawing or even Chinese hieroglyphs.

How to make a lamp for these templates, see other options for making lamps from paper and cardboard, see how lamps are made (they are lanterns) for the Haloen holiday from the same materials in our video selection.

Video selection on the subject of the article