Whether sewers freezes. What if you have frozen the sewage and plumbing in a private house? But what to do if there are turns in the frozen sewer pipeline

The country autonomous sewer system may fail in the winter period, especially when the temperature drops sharply to high indicators with a minus sign. Such inconveniences, for permanent residence homes, just a catastrophe.

For reasons such a situation, specialists consider incorrect installation, given the weather changes in the region. As the masters say: "Noctural sewerage does not freeze, it works without failures all year round." It is impossible to disagree with this statement, especially considering the fact that the pipes are under the tilt and fluid, the temperature of which is not lower than room, is constantly moving towards the accumulative tank.

Peacon is the fact that the freezing that happened cannot be eliminated before the arrival of seasonal heat.

Causes of fluid freezing in pipes

mounting error;
water supply faults;
clogging of sewer pipes;
insufficient thermal insulation of pipes;
invalidly selected pipe diameter.

Error in the installation work does not include inclusion of the angle of inclination, due to which the liquid samotor is ensured. Liquid, stopping in a pipe, under the action of a low temperature freezes, layering and blocking pipes, regardless of the diameter of the pipe. In addition to such a defect, the cause can be the location of the pipes above the level of the Earth's freezing, even the insulation material does not help in cold winters.

A malfunction, in this situation it is believed to be the appearance of leaks, as a result of which cold air penetrates through the air channel in the middle of the sewer system than and causes freezing. A signal can be a decrease in water pressure in the water supply crane, the cause of the ice layer inside the pipes.

Bores formed in the pipes by accumulating solid particles of large diameter, form a stagnation of a liquid, which gradually acquires a solid shape. After that, exploitation becomes impossible, due to not working capacity.

Ways to solve a frozen problem

If the freezing at an early stage, in time drew attention to the appearance of the problem, did not give the system to the market completely, resort to the defrost method. Detergenting, taking into account with a small area with a frozen liquid, it is done defrosting the water in the flow of boiling point, into the drain hole. It is important to take into account the technical characteristics of the installed pipes if the pipe material cannot withstand the sharp change of temperature, such procedures do not exercise, the pipes can burst, will have to replace the spoiled area.

If you managed to establish a place in which the liquid frozen, the circuit section is heated by special tools, a soldering lamp, other devices. For plastic pipes, a steam generator is used, the device forms water vapor, the temperature of which is above 100 ° C, warms and defrosts ice inside the pipe.

There is a method of electrical defrosting, for this use terminals and an electric generator, if possible, use direct connection to an electrical power supply. Under the action of current, the walls of the pipes are heated than the ice melting is determined, which formed a blockage.

After the system was activated, prophylactic measures should be done so that the problem is not repeated. You can make a spiring system of boiling water once a week.

Technical innovations, such as chemical defrost chemicals, are rarely used, there are certain causes. The most basic reasons for the failure of this method is its value. Such a price and consequences that cause reducing the level of microorganisms in the septic tank is not justified. After such a defrost, a bacterial mixture will have to buy and clean the well of the well.

There are drugs biologically clean, it is not suiced, the interaction with water causes heat to occur than and melts ice.

The convenient way is selected independently. To do this, determine and take into account:

determine the place of ice cork;
the dimensions of the formed plug;
sewer geometry;
method of laying pipes.

Whatever the problem is, initially competently created sewage system with all the stipulated nuances, the best option.

Correct installation

Incorrect work performed is a huge minus, the problem will be repeated until we decide to the cardinal measures to eliminate the initial defects.

With the arrival of heat it is worth thinking about the works that in the future will not allow such a situation, the use of sewage will be without problems all year round.

It is better to carry out these work with the help of specialists, or with their participation. Part of the work of not requiring qualifications are performed independently to save funds. These species include land work.

After the pipeline separation system is excavated, the angle of inclination should be determined correctly. If not, land work continues to obtain true parameters.

This is better not to stop, especially if the region is located in the north of the country. To ensure the heating of the system can be a special electrical cable, which is installed on the surface of the pipe. Work on additional thermal insulation with the participation of heating cable passes as follows:

it is necessary to measure the necessary member of the cable;
cable acquisition;
purchases of insulating material;
needed adhesive tape.

The cable length is determined taking into account the location with the connection to the power circuit. The cable is cut to the pieces comfortable for mounting, the same procedure is done with insulating material. After preparation, transfers to the process itself of the implementation of thermal insulation. The cable is plipped down at the bottom of the pipe with the use of adhesive tape, along the entire length of the pipeline with the connection in the break places. The next step, the winding of the heat insulating material, which is firmly fixed.

In such works there are many nuances, such as a selection of cable. The technical characteristics of cable-conductor products are diverse, heat transfer depends on the material, the amount of lived, winding, other factors. Cable with high heat transfer before insulation material is covered with a special foil, it helps to direct heat to the body of the pipe itself, not port the coating of heat-insulating matter.

Cable heating technologies have many types. A popular view is considered a spiral winding, foil and building insulation material create the perfect combination. The spiral winding warms the entire pipe, the consumption of electrical energy is insignificant, given the resulting beneficial coefficient.

Such systems of winter heating of sewer tubes are additionally equipped with temperature sensors, which are followed by the ambient temperature and the body temperature of the pipe, to maintain the perfect balance, electricity saving. In addition to the sensor, the relay is installed, which disjects the power circuit after the received signal from the sensor to achieve the maximum heating temperature of the pipeline system.

It can be adjusted independently, calculating the time to achieve a certain temperature, according to the technical capabilities of the selected cable product.

This insulation method is the most effective today. Regions with warm winters do not need such high-quality insulation, it suffices to lower the pipes below the freezing line, additionally making the thermal winding of pipes specially intended for this construction materials.

Freezing of the septic tank

Unfortunately freeze not only pipes. Freezing septicism The problem is no less important. The main reasons is:

drainage;
distance.

Due to the drainage, the freezing septicity occurs more often. The malfunction in the removal of water causes the gradual filling of the reservoir, after which immovable impostations are frozen.

Winter in our latitudes are so harsh that waking up in the morning you can find that the sewer tube has frozen. This trouble is corrected, although there will be some effort and time to solve such a problem. Of course, so that this does not occur, it is best to take care of the sufficient depth of the sewage laying in advance, at least below the level of primerization of the soil, and good thermal insulation.

But if such a misfortune happened, then you need to act immediately, without waiting for spring.

Of particular difficulty represents the defrosting of the pipe laid in the ground at a depth of less than the one that would ensure its non-freezing, but more than that on which it is easy to reach it.
It happens that the plumbing freezes, but if the sewer pipe has frozen, then the first thing you need to know is the material from which it is made. Each view has its own features of defrosting, from which we will begin our article.

Features defrosting various types of pipes

Defrosting of metal pipe

If the pipe is metallic, then it is possible to defrost it using a welding machine:

It is best to connect the tension to the ends of the frozen area, however, and just can be connected to the pipe too.
Natural grounding will provide current passage. You can use a safe voltage of 12 volts, but in this case the process will last long.
Heating from the flow of current on the pipe and on ice will contribute to the gradual defrost of ice tube.

Defrosting pipe from dielectric

Plastic or ceramic pipe requires a different approach. No hot water here can not do. It is better to use a technical brine from the cook salt, it has a greater heat capacity.

The main complexity is that boiling water will not go through the pipe scored. In order to deliver hot water to a place of congestion, a flexible tube or a smaller diameter hose, such as a metal-plastic heating or tap pipe, will be required.

Such a pipe has sufficient rigidity to move directly through the slightly lowered ice, and some flexibility for repeating not very sharp turns of the track.

Technology Next:

it is necessary to try to shove the pipe as deep as possible until it is reproached into the ice;

gradually, through the funnel, start pouring hot water into it; Chilled boiling water will arrive back;
continue to push the pipe, pouring boiling water until the stroke is completely passed, and the occasion of the outlined water in the sewer will begin.

If the pipe is winding

The cases described above are pretty simple, since the pipe in them is considered relatively straight. And how to melt the ice in the sewer pipe, if it has a complex underground configuration with multiple knee and bends there are different types of pipes?

This is also possible, but three subjects will be required:

construction hydraulic level, which is a long transparent hose used by builders to determine high points. He is inexpensive, and it is easy to buy;
steel wire;
ordinary enema or, in a different way, Esmark's mug.

Technology defrosting sewer pipes such:

a defrosting flexible cable is manufactured. To do this, the wire must be closed with a hydraulic level and fix.

The working end of this design should be in the form of a speaker on a centimeter and curved loop of the wire end.

It is necessary to bend it in order to meet an obstacle, the wire did not rest in it, but bypassed the party.

saving this system into the pipe, you should pour boiling water into the hydroelectric background and thus gradually move forward.
it should be taken in advance about which water will be assembled in which capacity and cooled boiling water. To do this, it is best for the pipe to substitute a bucket or other dishes that then do not collect puddles with a floor with a cloth.

This procedure will take several hours. Practice shows that each passing meter time consumption is up to an hour. This is a slow but true way. Boiling water does not regret.

What to do, so that the water in the sewage pipe is not frozen again? After all, the soil remained freezing and very quickly cool the entire pipeline. So that this does not happen, we will have to pour water all the time in the sewer. It, even cold, still has a temperature above zero and just will not freeze.

And with the onset of spring and summer, you should take care of the heat insulation of the sewage system. Methods for this a lot and materials too. You can also take care of the deepening of the pipe below the level of primerization of the soil.

Normally, sewer pipes should not be blocked: wastewater leaves gravity, and their temperature is high enough. However, such accidents happen often.

SML sewage can be avoided (see onwww.inrusstrade.ru. ) - a fasten hermetic system with good bandwidth.

But still, what to do if the tube of sewage frozen underground? Of course, to warm it up as quickly as possible, so as not to freeze the entire pipeline.

Causes of Ice Tube Education

Taketing for the elimination of this difficult problems in a private house, it is advisable to immediately find out why the system grabbed. The reasons for this can be a lot:

Disadvantage Trench or small pipe cross section. Waste mass move slowly, and as a result, the sewage was frozen. In this case, the most extended traffic jams are formed.

Small depth trenches (should be deeper than the level of primerization of the soil).

Violation of drainage in local septic. The crowded sump delays the fluid in the pipes where it freezes. The exit here is one - periodically pump off the contents of the tank, and in the summer it is possible to break the breakdown.

Siblors. It is often that due to dropping in the toilet garbage, the sewage pipe froze.

Bad thermal insulation.

Leaks. If a slightly leaks faucet or toilet, water can align the layer inside the pipe. It also threatens the blockage of the system.

The revealed cause of the accident should be eliminated (now or in the warm season), otherwise the problem will arise again.

How to defrost metal pipes

Noticing that the sewage was freezed in a private house, you need to act quickly. First, determine where it grabbed, pushing inside the wire. If there is access to the pipe, it is heated by a construction hairdryer, a thermal gun or a gas burner. But in most cases the pipeline is hidden underground.

Often, the plot occurs at the entrance of the pipe into the ground. If so, then you can heat the portion of the soldering lamp, previously touched it. But it is not always lucky, so other ways are also worked out.

Using heating cable

To defrost the cast-iron pipeline, a welding machine with a voltage of 30-70 volts is used. It would be best to connect the current at the point of the freezing point if it was found. If not, the terminals cling to the ends of the pipe are connected to the phase, and the second wire grounds.

After a few hours, the ice at the walls will begin to disappear, plums will appear. Next, boiling water is poured into the pipe, at the same time pushing and turning inside the plumbing cable.

The question is how not to let the belling well freeze, is solved easier. The hatch is insulated in advance by foam, minvata or straw mats. Many make brick formwork over rings, filling it with a grain material.

Defrosting plastic pipes

If the sewage is frozen underground, salty boiling water pour into the pipe (2 kg of salts on the water bucket). The method is effective if the plug is located near.

Otherwise, the water will cool before it gets to it. In this case, the pipe of the small diameter can be pushed into the pipe until it is stored in the obstacle. At the other end, the funnel is strengthened, into which the hot water is poured.

It is necessary to be prepared for the fact that the waste masses will pour back until the ice shoves. The process is not stopped: the pipe filled with water will penetrate.

If the channel is direct, it is better to use a rigid metal-plastic tube instead of the hose. It can be simultaneously pierced by a deciding ice tube.

What if the sewage was frozen with a composite pipeline?

The following devices will be required here:

Construction hydroery in the form of a flexible transparent hose.
Steel wire.
Esmarch's irrigator.

Wire and hose fasten with tape. The end of the wire must be bent in the form of a loop to bypass the obstacles, and not rest in them.

On the other hand, the hydrorette is connected to the circle of esmark. Pulling this system into the pipe, they begin to pour hot water into the circle. The process is slow - the passage of ice meter takes up to one and a half hours.

Using a steam generator

The principle of the operation of the device is simple - hot steam is served through the heat-resistant hose to the ice traffic jam. As the ice melts, the steam pipe is promoted on. The effect is approximately the same as when defrosting with boiling water.

Finally. In addition to the listed methods, homemade craftsmen are offered to pour into the pipes Painted vodka or kerosene, omit to the substrapeted waste mass "Army boiler" from blades and wiring.

But much more reliable and safe to use proven defrosting methods, and most importantly - do not delay with solving the problem. The earlier work will be started, the greater the likelihood of success.

The operation of the sewage is invisible until everything goes as it should be. Design and installation of the sewer system is accompanied by a consideration of many factors, including operation in conditions of reduced temperatures. However, the situation is not excluded when the sewage is freezing in the ground (moving a certain portion of the pipe). Under normal conditions, this should not happen, but laying errors can manifest itself in winter.

By the way, trying to understand at what temperature the sewage is freezing, it is necessary to take into account not only the placement of pipes, but also the material from which they are made (thermal conductivity of plastic and cast iron is very different), the diameter of the pipe, the angle of the slope, i.e. Action of many factors in the complex.

Why does sewage freezes?

The reasons for the freezing of sewage pipes:

invalid design of the angle of the sewer pipeline. Water does not have the ability to move by gravity, is stirred in pipes, which leads to moving in winter;

insufficient depth of occurrence. The septicch according to the SNiP is set at a depth of at least 2 meters from the soil level, the pipe system is located below the friction point characteristic of the region. But it is possible to dig a trench for laying the pipes deeply (or not possible) or frosts exceed the average and soil fluctuates deeper;

no insulation. Sewer pipes, laid above the ground freezing points, need insulation. The placement of pipes from the room is also necessary to isolate. However, in practice, such a requirement is either ignored, or an inappropriate thermal insulation material is used or its installation is incorrect;

small pipe diameter. If we consider the reviews of consumers, then most often the problem of changing the sewage is facing those who laid pipes with a diameter of less recommended 110 mm. Especially often they sin the owners of the villas and houses seasonally exploited. Due to insufficient diameter, the sewer pipe freezes faster;

siblors. It happens due to the mining of large objects or inadequate water flow into the system, in which a flask is formed in the pipes.

Causes of freezing Septica:

disrupted wastewater from septic. In this case, the septicch is overflowed, the heavy fractions are settled, and the water freezes;

septic tank removed from the source of wastewater. Then water, moving to the waste hole, is cooled, which leads to its freezing in the place of the junction of the pipe to the septic.

Many users independently performing work, do not think at all, whether the sewage is freezing. Indeed, the principle of operation of the Septic is that it is a container for storing wastewater with actively flowing decomposition processes. Since the decomposition of solid residues is highlighted heat, then moving is almost excluded. In addition, septic tank according to standards, is installed at a considerable depth.

However, no one is immune from force majeure and the country house owner is better to know in advance what if the sewage is frozen.

What and how to defrost sewage in a private house

There are different ways and means how to warm the frozen sewer (than melt the ice in the pipe). All methods can be combined into two large groups:

thermal method. Provides for the organization of heat supply to the place of freezing. Work is carried out slowly, but the risk is excluded damage to the pipeline system. This method is most appropriate at home, when there are no specials at hand, and the challenge of specialists is impossible or too expensive;

chemical method. Currently, the defrost to the chemical method is rarely practiced. First, because not all chemistry can cope with icing. Secondly, because it is a cost method. And, thirdly, because many users prefer local sewage, i.e. Systems that are capable of performing partial wastewater treatment.

One of the components of local systems is the presence of biological purification, and chemistry can negatively affect the vital activity of bacteria. Nevertheless, the simplest variety of it - the steep salt solution is applied according to the reviews, so far.

A more technological option, the use of a drug type MELLUD. The components of the cleaning agent for pipes Mellerud react with water to form heat.

Note. It should be carefully used a chemical method for defrosting plastic sewage pipes. Because Strong overheating can cause their deformation.

Sewage defrost - the procedure for performing work

If there is a problem and sewage in the private house frozen, you must first determine the place of the ice cork. The masters note the importance of compliance with the order of work, and begin better from the outlet of the water from Septic. Such an order of work is due to the fact that the system of sewage pipes is designed with a prerequisite for ensuring the unimpeded water flow. So, all pipes, incl. The flow tube is located under the slope of the exit.

Ice traffic jams need to be cleaned so that the water has the opportunity to drain naturally. Otherwise (when performing work outside), you need to be prepared for the fact that the drains will go in the opposite direction, which will cause the need to pump them. This convincingly proves that it is necessary to start work in the direction of the septica to the inner pipes.

But there are exceptions to this rule. Ultimately, the order of work will determine such factors as:

the place of formation of ice traffic jam. If the water frozen in the inside of the sewerage (unheated house), then it will be much easier to defrost;

cork dimensions. Perhaps the dimensions of the ice tube will be only a few centimeters, then the volume of water that needs to be populated can be neglected;

geometry of the sewer system. The more direct sites in the system, the easier it is to fix the ice tube;

method of laying. Usually sewage is placed under the ground. And if the ice was formed in pipes located at a sufficient depth under the layer of frozen land, the number of options for use is sharply reduced. It does not break from the septica - you have to maintain work from the room at home.

The easiest way to establish the winter operation of the sewer system will appeal to specialists who provide services for the defrosting of sewage. The masters not only know how to defrost frozen sewer, but also have special equipment, and also give a warranty. However, for various reasons, many prefer to solve the problem on their own. And as evidenced by the reviews forum, successfully and quickly.

What if the sewage was frozen in a private house

Wheelning methods will differ depending on the site of the ice cork. Consider every problem and solution options.

Frozen sampling of sewage

Sewer plux or wastewater from the septica rarely moves off, because It is located deep in the ground. However, if the water is not done, it will lead to overflow of the septica and its freezing.

What if it is frozen channeling?

To defrost drain, experts are advised to pour septic with hot water or brine. Then you should pump up the drains from the septic, and repeat the fill of water. Over time, warm water will eliminate the ice tube, and the system will function in normal mode.

The sewer discovery is also called a pipe that takes wastewater from the source of their formation: in the sink, toilet, bathroom. It can penetrate if the room is not heated, and the water from the drain was not descended. Or, the flow of water is too weak. As a rule, plums inside the room freezes in the place of adjustment to the source of the drain and is easily eliminated by using a hair dryer. In the same way, the problem is solved if the sewage is frozen in a private house.

Frozen septicity of sewage

This is possible if the drain is incorrectly organized.

What if frozen septicchik?

To resolve the problem, such measures can be taken:

heated with a light bulb. The light bulb is placed inside the septic. Thanks to the power of the lamp, the environment is heating, and score gradually pulls away. The method is very slow, moreover, you need to monitor the water level and lower the lamp below. From practice: 1 m. Ice melts per day, at a temperature on the street in -15 degrees;

Frozen sewage pipes

The most difficult of possible situations, since there are two obstacles: firstly, the pipes are located underground, which makes it difficult to use external heating, secondly, it is difficult to accurately determine the specific place where the pipe peered.

How to detect the formation of ice plugs?

You can determine the place of movement using two pieces of wire. To do this, one of them needs to be started in the sewer system from the side of the house, and the second side of the septic. Knowing the length of the sewage and the amount of the distance to which the wire managed, it is possible not only to find (reveal) the place of formation of ice plug in the pipe, but also its size.

What if you frozen the sewage pipe?

Ways to remove ice traffic jams by heating.

Outdoor heated

Ensures the extraction of the soil to the level of pipe laying. After direct access appeared to the pipes, you can:

use open fire: burner, soldering lamp. You can wind up the pipe with a rapid or make firewood and set fire. The method is suitable only for metal, cast-iron sewage pipes;

wrap foil, then heating cable and connect to the network;

use heating tape;

use a construction hairdryer for plastic pipes.

Recommendation. Users advise to cover the warm-up seat insulation, so defrosting will pass faster. At the same time, passive heating itself in case of freezing of sewage pipes does not fit, because The thermal insulation material does not heat, but only protects heat.

External heating is not very popular, due to the complexity of extracting frozen soil over the system of the pipeline. The question of how to warm up the frozen sewer, access to which is impossible? The answer is obvious - only from the inside.

Internal heated

The technology implies an effect on the ice from the inside, i.e. directly inside the sewer pipe. Among the options you can offer:

heating the wall, if the sewage pipe has frozen indoors;

use hot water.

In order to clean the direct pipeline you need to start a hard hose in the sewer, combine it with a funnel into which water is pouring. As ice melts, the hose can be promoted further. Increase the efficiency of the procedure, you can use water with salt. The ratio is offered differently from 1:10 to 1: 1 (salt: water).

To defrost the sewer pipeline of a complex configuration, the same actions are performed, but a flexible hose is used. The hose is primed up to a flexible wire with a step of 500 mm. So that the edge of the wire spoke on the edge of the hose by 20-30 mm. The end of the wire is bent inside for stiffness. The free edge of the wire should be 10-15 mm, the task of bypass obstacles and lead the hose. As the water melts, the hose pushes further. Instead of a funnel, you can use a pear.

Choosing this method you need to consider that:

a) the water temperature should be more than 80 ° C;

b) water supply is carried out continuously;

c) excess water will be back out, so under the pipe you need to install a container for its collection.

The productivity of the method is 1 m. Per hour, with a pipe diameter of 110 mm.

the use of a small boiler, which will warm the water directly in the jam.

According to user reviews, the task successfully copes the so-called "army boiler", which is a simple design. Two blades inserted in a pet bottle cover with a pitch of 5 mm. The blades are screwed with a copper monoposition cross section 2x1.5, the inverse end of which is provided by the "fork" and is inserted into the outlet.

When eliminating ice cork in plastic pipes, you need to ensure that the heating element does not touch the pipe walls. To do this, it is placed in a solid lattice shell of the grid (wire);

using a welding machine connected from two sides to the pipe. Suitable for metal pipes;

use of any hot liquid, such as alcohol. From practice, volume 1 mp Pipes with a diameter of 110 mm is 8 liters. This method is expensive;

using a steam generator.

What to do so that the sewage does not freeze in winter?

To eliminate re-movement, it is necessary to periodically merge (especially during severe frosts) into the pipeline significant volumes of hot water.

Solving the problem of freezing water in sewage, should not be limited to bringing the system to full functional readiness. After all, the probability of repeated freezing is not excluded.

Among the prevention measures of sewage freezing, you can allocate:

proper insulation of the sewer pipe. This procedure must be performed on the pipeline laying phase;

laying pipes to the depth below the ground freezing point;

connecting a heating cable (resistive and whether self-regulating).

The problem of frozen sewerage occurs, unfortunately, not so rarely. Therefore, the question of how to defrost the sewer pipe, sounds often. To respond to it, it is necessary to understand the causes of the formation of an ice cork. And they mainly belong to the purely technical characteristics of the construction system. Namely:

the slope of the pipe was incorrectly chosen, it is optimal for sewage to be 2-3 mm per 1 m.
a large number of taps and knees of the track;
the sewage network was laid above the level of the fruit of the soil and poorly insulated;
the pipes of a smaller diameter were installed, which reduced the throughput of their ability.

Even the presence of one of these reasons immediately becomes a problem that will be determined by the question: the sewage has frozen - what to do?

Frozen sewage

In fact, what can be done, in which the sewage can be done. In principle, there are not so many options. The thing is that the sewer system is usually laid deep underground, to get to it in winter, the digger ground, the problem is not the simplest. But if there is no other way out, you will have to dig.

True, it should be noted that with an open sewer pipe can only be operated if it is made of metal. But before defrosting the sewer, it is necessary to determine the place of formation of ice cork. Make it can be very simple.

Takes for this hose or wire.
One of these products should be poured into the sewer track from the side of the house from the first any auditing window or a viewing well.
As soon as the wire rested into something hard, it means that there is an obstacle to it. Perhaps this is an ice cork.
To check and be confident one hundred percent, it is necessary to produce the same thing from the side of the septic. That is, a hose or wire is inserted into the open pipe and pushed until it stops.
Now from two sides, the same wire must be postponing along the laying line of the sewer tube. If they come together in one site, this is a guarantee that the stopper is located here.

If there is an observation well on the same site, it simplifies the process of defrosting the sewer system. Just shrinks access to traffic jams.

Forgot to insulate

Heated metal pipes

So, the place of ice cork is defined, you can now dig a pit or a trench to the pipe itself. Usually metal pipes for the sewage system are cast iron samples with a fuse-free connection system. Dotted to the highway, now you can spend defrost.

The easiest and most effective option is to take a soldering lamp, ignite it and walk along the pipe. If there is no available, you can get a bonfire on site. Someone even offers from two sides of the pipeline to connect an electric current, on one side of the phase, with another zero. It is unlikely that it will help, although a purely theoretically, this option must work.

Metal pipe you can warm up the burner

Heated plastic pipes

To largely fortunately, plastic pipes almost completely in the sewage system were replaced with steel. They have a very smooth inner surface, which guarantees the high passability of sewage drain. But, as already mentioned above, the incorrect installation of pipes can lead to the formation of an ice cork. Therefore, we will deal with the question how to heat the sewer from PVC pipes?

As in the first case, it is necessary to find the exact location of frozen drains. That is, you need to do all the manipulations with the wire or hose. Do not dig anything, any action on a high temperature plastic, and even more open fire, will lead to its melting, respectively, the pipe will lose their integrity and cover holes. That is, there can be no speech about the tightness of the sewage.

Defrosting ferry

Influence on the ice tube, it is necessary to inside the pipeline with hot water or steam. To do this, first of all it is necessary to determine the distance from the septica to the cork. If it is large, it is better to use water, if small (up to 5 m), then you can apply steam. In any case, it is necessary to prepare, that is, to dial a large amount of hot water, for example, it can be a barrel mounted on a fire. If pairs are used, you will have to install a small power steam generator. The first option is easier, and more reliable.

So, the hose is inserted into the septic septic septic tube. A funnel is installed in the other end. The higher it will be installed, the better, but even the level above the ground is sufficient to deliver hot water to the place of the requirement. Now you just need to pour heated water into the funnel. She will reach ice on the hose and starts to pull it. At the same time, the frosthed drainages of the sambeck will be drained along the pipe into the septic tank. That is why it is so important that the hose is inserted from the side of the septic reservoir.

Of course, if the distance from the team well to the plug is large, it is simpler, probably, the fill of hot water to spend from the side of the house. But then there is a problem associated with pumping melt drains. After all, they will be gathering over the plug, remaining in the sewer pipe itself. Well, if the ice block is not very big. Hot water will melt it gradually, and all the drains along with slices of ice are falling further along the pipe, and from there in the septic tank. And if the plug is big, if the sewer tube froze (a large plot) - what to do in this case? How to pumped up frosthed sewage drains?

Pouring hot water into the sewer pipe

In principle, the option is one. Install the pumping pump and turn it on periodically. That is, you will have to insert another hose from the pump in the sewer tube. How to understand when turning on the pumping device? Once water appeared on the side of the hoses input, you can turn on.

Alternative solution

There is another option. It is simpler, but not as effective as defrosting with hot water or steam. To do this, you can use a hairdryer (construction or household). It is simply inserted into the end of the pipe from the septic side and include. Hot air penetrates the pipeline filling itself. Having reached the ice cork, he begins to clean it. This process is not fast, it will take more than one hour until the whole ice plums melts.

Conclusion on the topic

So, what should be paid attention to, before decaying the sewer plastic tube or metal? It is necessary first of all to determine the sizes of the traffic jam. What she is more, the harder to cope with it. And you can cope. The most important thing is not always obvious ways of defrosting can be used immediately. It is worth thinking, and whether all the might is worth using this technology. Maybe there is a way simpler? Or perhaps, you should not pick up with the sewer yourself, it may be better to call specialists.

Do not forget to rate the article.