Wall coal hanger with their own hands. Outdoor clothes hanger do it yourself, photo. Outdoor hangers: types of materials and structures

Outdoor hanger - Mandatory attribute of any hallway room, be it apartment or country house. Its price depends on the originality of the execution and quality of materials. The easiest option is to purchase such a design at the nearest furniture store. But there is a different way out of this situation, so as not to overpay - make an outdoor hanger for clothes with your own hands.

A little theory from the course of physics

To achieve this goal, a little knowledge of physics will be required, as well as brew materials and tools. Let's start with the first one. The basic requirements for the floor hanger are stability and absence of sharp elements so as not to damage the floor, wall or clothing.

Stability is achieved in several ways. If the floor hanger relies on one basis, as a rule, in the form of a crosslinor or a circle, then it is necessary to make the center of gravity to be as low as possible. You can do this using more heavy materials - massive wooden bars or metal.

If the space of the hallway is allowed, it is advisable to install the hanger for two, and even better - three points of the support. In the first case, the broad grounds will need that your attribute does not fall on the side, because it is evenly placed by clothing problematic. Therefore, if possible, you need to choose a support at three points.

So that the base of the floor hanger does not scratch the floor, it will be necessary to use materials as a "sole" that will be softerly coating.

Tools and materials

Required tools

So, here is a list of tools that will be needed for the manufacture of outdoor hangers:

cross (figured) screwdriver;
self-tapping screws of different lengths and thickness;
sandpaper;
drill;
dried (set);
hacksaw;
ax.

Set of self-sustaining

Also have to be stocking in the following materials:

a dried tree (cherry, sea buckthorn, etc.) or several such if the hanger is planned with several points of supports. You can buy ready-made processed blanks;
bruks (assentful, no less than 60 cm long, the optimal section is 7x7 cm.);
metal wire (for hooks) or ready-made decorative hooks;
carpentry glue;
a piece of rubber (or silicone) with a thickness of no more than 3 mm.

Wooden bars for work

Instructions for the manufacture of outdoor hangers with crosses and hooks

First you need to free the stem from the bark, as well as coarse bitch. Of course, it may seem that with the bark the hanger will look much more naturally, but over time it will crumble, and the garbage is to deal with all residential premises. In addition, small insects can be in the cortex. Yes, and clothes will cling to irregularities.

You can free yourself from the bark using an ax or a massive knife. As soon as this task is completed, it will be necessary to walk several times on the remaining part of the emery paper - first coarse, then shallow. After grinding, the surface will become smooth, and the likelihood of hooking clothes will be minimized.

The following task is to make the basis. As in construction, only the design will be stable and durable, which is granted integrity. Therefore, the base and tripod of the hangers must be one.

The base and tripod of the hangers must be one whole

You should not first make a cross, and then to attach the body of hangers to it from above - this design is very quickly loosened and can fall out of the base under the weight of the clothes.

Here is a rule that you should adhere to, the lower edge of the tripod should be flush (that is, on the same plane) with the base sole.

We proceed to measure the diameter of the barrel. We need it in order to choose a bar of the appropriate width. If the bars are wider, then you need to cut the knife along to the desired size.

The standard heating height is in the range of 180-200 cm. For them, it is necessary to make a crossover with departures from 25 to 35 cm. Therefore, we will need 2 vehicles with a length of 60 cm. That we will cut exactly in the middle to get 4 30 cm blanks.

Now the difficulties begin. Even if you have to heal and attach these 4 bars to the round trunk, the design will be unstable, and after the first fall due to uneven wipers, it will simply fall apart.

Therefore, we will proceed as follows: We will put the barrel to the floor and stick the preparations from the four sides to it. It will not be possible to connect them in this form, so we will make inserts in the form of triangular wooden elements on the bars exactly in the part of it, where the body of the hanger is. Such "triangles" are attached to the bars with the help of self-tales, and also to the tree trunk - in exactly the same way.

To strengthen the design, in those places where "triangles" will be attached to the timing brushes and to the trunk, it is necessary to first drill with a drill hole, with a diameter of 2-3 mm. Less than the fastener diameter.

If you simply turn the screws into the tree, that is, the likelihood of cracks that weaken the design.

After this procedure is completed, you need to fill in the resulting drilled spaces with glue, and only after that start turning the screws.

The obtained design of the floor hanger can not be ideal in terms of sustainability - it often rolls up with one brush of crossfins on another. To correct this drawback, you need to use pieces of rubber, which should be pasted on the lower part.

So that the tires perfectly glued to the surface of the tree, it is necessary to go through the wood surface with sandpaper and make several scratches in different directions.

The frame is ready, now you need to give a hanger functionality - add hooks for outerwear, which can be remote, that is, to be at some distance from the trunk. There is one rule: the center of gravity of hanged clothes should not go beyond the limits of the cross, otherwise the design will be unstable and falls.

No matter what hooks are used - homemade or decorative, it is impossible to fix them directly to the trunk, since the floor hanger will quickly come into disrepair. You can do the following: Cut from available squares Square, the length of the sides of which will be somewhat larger than the diameter of the barrel used as the body of the hanger. Before fastening the "square" to the top, you must first attach hooks to it.

Decorative will suit more, because from the wire of a beautiful form to achieve very difficult. Such hooks are attached to the tree, as a rule, with the help of one or two screws.

If there is a time and some skills in working with a tree, then with the help of the chisel, you can cut into the squares connected to the top of the floor hanger, so that the base of the hook is subsequently "drown". This is a more aesthetic solution than just sitting on the self-tapping screw.

After all hooks are attached, a square wooden element is needed to connect to the top of the barrel. This can be done by one or two self-stakes according to the technology described above.

The final stage of work is to give the aestheticity of the obtained floor hanger. First of all, it is necessary to close the lower part - the cross with all the fasteners. This is allowed to use fabric, rattan, wooden or plastic rails. The hanger itself can be painted with a protective layer of paint or varnish - both natural color and any other, depending on the color gamut of the room decoration. The layer must be deposited at least 2 times.

Making Hangers for Suit

Scheme of outdoor hanger for suit

Outdoor hanger for men's suits has a slightly different design and is made of wooden bars.

You can make it by this algorithm:

measure and cut blanks according to a predetermined project;
carefully process them and polish;
make fasteners in the right places;
collect the hanger according to the scheme presented below;
perform finishing finish;
screw to the base roller wheels or glue rubber gaskets.

One of the convenient ways of storing clothes is an outdoor hanger. It can be put at the entrance and leave here the upper clothes. Other models are more suitable for bedrooms, dressing rooms, children.

Types of floor hangers and place of their location

Some types of floor hangers are placed in certain premises. For example, hangers for outerwear put in the hallway near the door. It is convenient: you can immediately get rid of clothes. Outdoor hanger stand under the shoulders are more universal. Such products can be put in the corridor, in the dressing room, even in a nursery or bedroom. They host a large amount of clothing and they can be replaced by a wardrobe.

Standing hangers under suits, shirts and pants most often "registered" in bedrooms or children's (if a child is a schoolboy). It is there usually dress before going out of the house. There are also stool hangers. This is actually one of the options for costume hangers. Just legs and stops taken the shape of the seat.

What materials do

Outdoor hanger is most often made of metal or wood. Both of these material are durable, plastic, durable and relatively inexpensive. Some details are plugs, parts of hooks - can be made of plastic.

Most often you can see outdoor metal and wood hangers

Plastic inserts are more common on metal hangers with a lower cost. If not the elements of the supporting structure are made of plastic, it is not bad and such outdoor hangers can be bought without thinking. If the elements of the reference design are made of plastic, it is better to look for another model.

Metal hangers

The largest selection of outdoor metal hangers. Usually they are made of thin-walled pipes of round or square section. Metal is most often black coated with protective coating. It may be paint (most often - powder spraying), nickelting, chromium. In recent years, a new protective coating has appeared - plastic film (PVS). This is also a good option, since the film is impenetrable for moisture, air. For such products it is easy to care for, as the surface is smooth, without pores.

If the floor hanger will serve to accommodate heavy winter clothes, pay attention to the thickness of the metal when choosing. Minimum in this case - 1 mm. If in the description to the product The thickness of the pipe wall is not indicated, most likely the wall is very thin and is suitable for easy clothing. Indirect signs that will confirm your guesses are the weight of the product and the price.

Wooden

Wooden hangers can be sharpened from the array, and may be teams. The first option is significantly more expensive. The teams are 2-3 times cheaper, but not too different outwardly. The presence of joints in normal quality products are minorly noticeable, so with a limited budget it is quite possible to acquire products of economy class.

Wooden floor hangers are well polished, covered with protective coating. Usually use varnish or oil. Varnish creates a protective film on the surface so that it is easy to care for such products. Oils for the protective film tree do not create, but they are not worse. When processing oil, wood structure is clearly visible - all fibers, drawing.

Standing hangers for clothes in the hallway

Outdoor hangers for outerwear in the hallway most often are a rod, on which hooks for clothing of different lengths and shapes are placed on a different height. For stability, the design is equipped with a circular (rarely square) lean base. They can be made of wood or metal.

The height of the rack is full-150 cm and above, and the base is a circle with a diameter of 35-45 cm. For the hanger is stable, it is necessary to draw attention to the fact that the bottom part is weighted. And anyway, such structures require a careful relationship: hanging clothes need evenly. Otherwise, the hanger may fall.

There are outdoor hangers for the upper clothes of this type, but made differently. Several pipes or metal strips bend with a certain radius. In this case, the upper part has a smaller size than the lower one. This design is more stable, but requires more space that in a small hallway is not always possible.

Stands under the shoulders for clothes

A rack hanger for clothes on her shoulders is a comfortable thing if there is not enough space in the cabinets. They consist of the base of the rectangular shape, one or two pipes, for which the shoulders with clothes hang.

Rack hangers make metal and wood. Metal is made of pipes, there are forged. Some models of metal racks for clothing have an adjustable height. For long clothes, their rack can be raised higher. The maximum height is 150 cm. For short clothes, you can install at an altitude of 80-90 cm. This is a minimum height, and there is still intermediate positions.

In some cases, an outdoor hanger on wheels is useful. It is easy to move from place to place without removing the clothes youth. There are children's models of outdoor hangers of this type. They differ only in height and more "funny" colors. Still children's floor hangers can be made of plastic. Children's clothing weighs not so much, so plastic strength is more than enough. And the price of plastic floor hangers are the most inexpensive.

Folding models - access in case of reception

For those who take guests in large quantities, it is problematic to accommodate their upper clothes. For such cases, there is a foldable stand under the shoulders for the outerwear. In the folded state, it takes quite a bit of space and can be stored in the storage room.

Outdoor costume rack

The problem of storing a business suit is easily solved with the acquisition of a special floor hanger. She is something like racks, only with special puffers for a jacket and a trouser crossbar.

There are racks for a suit of wood, metal and plastic. Plastic in this case is not bad: the load is not foreseen, so that the strength of modern plastics is more than enough.

If we talk about useful options, this is a shelf or box. It is convenient to store business little things: glasses, cufflinks, wallet, keys from the car, etc.

Put outdoor hangers for a suit usually in the bedroom, in the dressing room. It can be convenient to have a similar device in the office. There are different models, you can choose any interior style. And some options look like a designer decoration.

Hanger chair and hanger bedside table

There are rather unusual hanger models. They are combined with furniture objects. For example, there is a hanger chair. Models are different: with a suit for a suit, just a barbell under the shoulders or with a rack for outerwear. For small apartments, this is a very good option. Places takes as much as an ordinary chair or a banquette, and also serves for storing clothes.

Floor hanger with chair and bedside table - for the full use of the site of the hallway

Another option: bedside table. The lower part of such an outdoor hanger is much heavier than its upper half, so that it will not turn away from the pair of hanged coats. The second plus of such furniture is the optimal use of space. The trouble of all outdoor hangers is that the lower 50-60 cm remains unsuitable. In the case of a sleeping bedside table, this is not. This is another good way to rational use of space for small vessels.

Such hangers can be used not only for outerwear in the hallway, but as mini wardrobes in the room. It all depends on what type and design you will choose. Hangers racks for clothes they are functional, easily rearranged from place to place, and free the backs of the chairs from the clothes unnecessary there.

This article contains some interesting and simple ways to make an outdoor hanger for clothes with your own hands. They will not take much time and effort.

Choose the option you like and go to the interior change!

Necessary materials:

Two copper pipes long 3 m and 2 cm thick, each one will need to cut into such parts (this can be done in a construction store, where you will buy everything):

1.5 M. - the height of the hangers (such a height must be enough for jackets and for the accuracy, but you can take more or less at will);
1 M. - the size of the pipe to which you will directly hang things (it can also be taking longer or shorter, calculate how many things you want to place there);
two tubes in length somewhere 20-25 cm - With them we will make the legs of the hangers.

That is, 2 copper tubes are 1.5 m, 2 to 1 m, 4 to 20-25 cm.

4 copper removal-corners (tubes bent at an angle of 90 degrees) for fastening pipes among themselves, select the diameter under the pipe (approximately 2 cm);
2 T-shaped connectors;
2 caps for pipes;
Glue (epoxy glue or consult with the seller in the store, which is what is in stock is suitable);

Step-by-step instruction:

Step 1: Measurements

Measure the space on the floor where the hanger will stand, make sure it fit. If you take the indicated dimensions, in the end it will turn out 150 cm x 100 cm x 45 cm.

Tip: Correct the dimensions if necessary.

Step 2: Collect the legs of hangers

We begin to lay out the floor hanger from the legs, we make support and rack. To do this, take the first pair of tubes of 20 cm and secure them between T-shaped connectorAnd then we do the same with the second pair.

Step 3: Fresh Protective Caps

So that in the middle of the pipes that will serve as legs, dust and dirt did not fall, you need to close the holes. For each of the two folded legs folded in the previous step at one end, attach the cap for pipes.

Step 4: Basis

On the tubes with caps on the other hand, attach the corner in this way: when the corner lies on the floor, the T-shaped connector located in the middle of the legs should be directed upwards.
Take one of the pipes of the meter length and insert it into the corners, now the base of the hanger is ready.

ATTENTION: To securely fix the design, you can use the glue (at least in all places of compounds), but then the hanger cannot be disassembled and folded again (when moving, for example).

Step 5: Side Stands

Insert into each of the T-shaped connectors, insert the side racks at one and a half-meter tube.

Step 6: Last bar

At each of the just set racks, attach the corner (they should be directed to each other), and insert a meter pipe in them.
You can still attach felt gaskets to protect the floor. Outdoor hanger is ready!

Note: Since this design is easily disassembled (if the adhesive was not used), it can be changed its length, for example, depending on the time of year: in the winter of things more - put longer pipes, in the summer in short.

Hanger of PVC pipes (budget option)

The method of manufacturing this floor hanger is similar to the previous one: pipes fold as a constructor, forming a hanger. But here we use no copper pipes, and PVC, so it will be much cheaper. And, of course, another new design idea.

Necessary materials:

PVC tube with a length of 2 m and a diameter of 2.5 cm, it must be cut to such parts: 12 cm (6 pieces), 80 cm (1 pcs), 20 cm (2 pcs) and 10 cm (1 pcs).
PVC pipe with a length of 50 cm and a diameter of 2 cm, cut it into 3 parts of 15 cm.
4 removal-corner with a diameter of 2.5 cm.
3 removal-corner with a diameter of 2 cm.
6 T-shaped connector with a diameter of 2.5 cm.
Glue for PVC.
Aerosol paint.
4 PVC adapter from 2.5 cm to 1.25 cm.
3 PVC adapter from 2.5 cm to 2 cm.
Felt gaskets for sex protection (optional).

Step-by-step instruction:

Step 1: Cut the tubes on the pieces of the desired size

First of all, we must cut PVC pipes for mounting in a rack. This can be made at home by the PVC cutter or ask for a construction store.

After cutting the pipes on the part of their edge, you can span, so as not to scratch, collecting the hanger.

Step 2: We sort materials

Now we have all the necessary parts and it is better to sort them for convenience, then the assembly process will be faster and ordered. Spread materials on piles, depending on their purpose.

For the stand hanger, you will need: 4 corners, 4 adapters from 2.5 cm to 1.25 cm, 3 T-shaped connector and 6 tubes with a length of 12 cm (diameter 2.5 cm).
For each hand hangers: T-shaped connector, PVC adapter from 2.5 cm to 2 cm, 15 cm PVC pipe with a diameter of 2 cm and a corner with a diameter of 2 cm (a cap for pipes can still be put on it).
For a rack: One PVC tube is 80 cm long, two to 20 cm, one 10 cm and cap.

Step 3: Collect the hanger

Stand

Crerate every two tubes using T-shaped connector. One of the three constructions inserted between two others, as shown in the photo. On the edges of the other remaining put on the corner, turning them down, so that they stood a hanger.

Hands

Fold together T-shaped connector, adapter, tube and cap, as shown in the photo.

Stand

Insert the 80 cm long tube to the T-shaped connector, attach one of the hands of the hanger on it, then attach a 20 cm long tube, another hand of hangers, again the same tube and hand, a pipe 10 cm long and a latter tower on top of the cap .

To keep the design better, it can be copped with special glue for PVC. Be careful with the hands of the hangers to glue them turned in the desired direction - the corners up.

Step 4: Painting

The design of the hangers is ready, but it looks still not very aesthetic. Gently and evenly apply the aerosol paint of the color you choose, do not blur the room.

Tip: So that the hanger is more stable, in the pipes, from which the stand is made, you can pour sand. After such a small tricks, the hanger will not fall and turn over.

Pipe hanger with multiple levels

Another hanger of this type, only with extended functionality: here it is not only to hang clothes, but to put shoes. Compact and convenient wardrobe.

Necessary materials:

PVC tubes with a diameter of 20-25 mm:
- 4 100 cm long
- 2 65 cm long
- 4 48 cm long
- 6 20 cm long
- 8 5 cm long
10 T-shaped connectors
6 Top Corners
Low shelf plate

We are folded completely similar to the two hanger described above.

Wooden floor hanger in 10 minutes

Necessary materials:

Wooden sticks (4 pieces) with a length of 180 cm and a diameter of 2 cm.
Rope: We will use it to tie together wooden sticks (you can also use leather cords, wire, or some other decorative material, the main thing is that it firmly and reliably fixed the design).
Aerosol paint: We used golden color to paint the lower part of the legs of the hangers (you can also use another shade or color).
Paint: We used four different colors of paint, one on each leg of hangers (but, of course, you can use the same color for all legs).
Malyary Scotch: When using aerosol paint, it will help not paint extra.

Step-by-step instruction:

Step 1: Prayes Supports

Color legs in selected colors, give the paint to dry.
Cut the malarious tape in the place where the aerosol paint should end, and gently apply paint on the legs. It is better to do on the street, or to store the floor with newspapers so that you can not drink anything. Spread the greasy tape.

Step 2: We form a hanger

Connect wooden supports along with the help of a rope, and then gradually push them out to the sides. There should be something on the basis of Vigvama, the legs must be placed quite widely, so that the hanger is stable and convenient to use.

Such a hanger takes a lot of space, so it is best to put it in the corner.

Interesting ideas and photos

Trees hangers

It can be neatly grounded tree trunk or his branch, or a folded wooden design. The main thing is that there was one support and the branches were accumulated from it - the handles of the hangers. Original and useful addition to the hallway.

Hangers-designers

The number of elements and design may differ, but combines all these floor hangers, what can be quickly folded, and also quickly disassemble (if adhesive did not use). Sometimes more expensive and noble materials are used, such as copper, sometimes wood or PVC, in any case it turns out beautiful and extraordinary.

One way to make the house is alive - fill it with original things. Even a simple furniture accessory as a hanger for an entrance hall with their own hands, as shown in the photo selection, it can become a real decoration.

It is necessary to stock up the necessary tools: drill, screws, cross screwdriver, 2-3 drills, hacksaw, roulette, fitting (devices for spilling boards with different angles of the bevel), level. To give a finished and neat look, you will need a skin with a large and small grain, varnish, a stain or paint.

From materials for hangers with their own hands, you will need:

so that clothes do not fall along with a hanger, you need to make a steady, heavy base. Thick wooden bars are suitable 60-70 cm long, or metal parts. You can take a support from the old artificial Christmas tree; Ideal for old ashistant floor lamp;
we will have to choose a suitable column, in building materials stores wooden components are offered, figurine treated on the lathe. The most economical option is a direct trunk of a young tree, by the time you use should be dry. The bark is removed from it, eye treatment is carried out. Its height should not exceed 200 mm;
a set of hooks, the number must comply with the estimated number of clothes on the hanger;
glue, for fixing the screws and additional fastening of parts (carpentry or other transparent glue);
so that the hanger does not slide on the floor, as well as to align the points of contact with the floor (so that it does not fall, saying easier), rubber is glued to the lower surface of the base (thickness from 1 to 5 mm);
to strengthen the center of gravity of the hangers, you can attach a small shelf in the form of a massive board, is installed on a metal corner, and is used as a shelf for bags or gloves.

Drawing of outdoor hanger

Wall-mounted hanger drawing

Creating the bottom

Prepared all the above, you can work for work - start creating a hanger to the hallway with your own hands. First you need to do a cross. The cooked bars are cut in half (each support of the hangers must be a scope of at least 30-35 cm), processed with a skin, are connected at right angles. For a dense connection on the parts of the Cross, it is necessary to choose a chisel to deepen in the width of the bar, combine the selected areas, they will be tightly, fixedly connected (see photo). Now, with the help of the fitting, 4 bars are peaked, which will serve as a support for the trunk of hangers, they must be screwed by self-drawing to the legs, as well as to the trunk.

Bar for the base of hangers

Future legs hangers

Before screwing the screws, you should drill the hole of the drill, it will save the product from small cracks that can significantly reduce its service life. The diameter of the drill must be less than that of self-drawing. Molded holes should be filled with glue for strength, and only then turn the screws.

Details of lateral support

The legs are screwed to the base of the hanger

For installation of lateral support, carbon black is used, as well as a gun, or a hammer with nails

Rubber is glued on the legs of the hanger, after gluing the product should not swing or slide - you will have to try.

Creating an upper part

Now you can go to the top of the hanger, place the hooks. It is not necessary to attach them directly to the trunk, it is better to attach a small square with in advance crochets. There is also an option: 4 brus combined with spanking with fittings are attached to the barrel, slightly retreating from the top. Under each self-solen, the hole is drilled and is filled with glue, this is a rule for the item that will be subjected to solid loads.

Now the product is over, you can go on an appearance. Taking emery paper, you have to go through the surfaces. It is better to cross the cross, cover with a cloth - close a rough design. Wash the hanger, cover with varnish (or paint and also label - it will save a fresh look for a long time).

Decor of the top of the hanger

Decorating the tops of the hanger

Decor of the top of the hanger

Original options

If a lamp is found in the house, then work is reduced repeatedly. It is necessary to remove electrical equipment, clean and paint (the excellent effect will give metal aerosol paints). For hooks, you can make a multiple holes with a drill on metal, to turn steel hooks (s figurative). If there are some skills to work with the metal - bend them from steel wire and weave.

You can still use the real village (well-dried, of course). Fully remove the bark, sand. The stand will serve roots, also peeled and properly focused. The branches leave only durable, located close to the trunk - Krone should not go beyond the support. Such a hanger in the hallway will be a real pearl of the interior created by their own hands. However, it is necessary to prepare for a long search for a suitable copy, and then - to long and very careful processing.

Combined option

A simple and interesting option, on the basis of which a variety of wall hangers can be obtained into the hallway. The toolkit is given in the previous description, and the following materials are:

bars;
two strong boards for attaching to the wall;
board with sufficient shelf width;
metal furniture corners;
reiki (instead of them it is better to take platbands, choosing to taste, they will only miss or paint and label);
hooks.

Timber is better to take processed, it will significantly speed up the product assembly process. Make this hanger in the hallway is extremely easy, boards, at the top and bottom are attached to the wall. The length of these fasteners depends on the length-planned length and must correspond to the length of the shelves (it is necessary to think over the dimensions of the new furniture accessory in advance).

Rakes are installed on these boards, with a small distance between them. Vertical location Check the level. At the bottom of the shelves for shoes, bars are used for this. Shelves are on the floor, which will later be able to calmly sit on them to convert. All joints are necessary to strengthen the corners, check the strength and loyalty of the lines.

A gross design of bars can be seen by rail, it will give the product a neat and finished look. Then the upper shelf is installed, it should be attached at the level of the top mounting board. Self-tapping screws should be included in the support, that is, they should be equal to the sum of the rack thickness and the fastener. Beautiful wrought-iron corners are suitable for this shelf, which will become aesthetic addition to a new piece of furniture. The final chord is the screwing of hooks, and then - treatment with a verse and varnish, or painting.

The design of this hanger can be modified, for example, to expand it with additional slats and attach a mirror or additional shelves.

How to attach the mirror

If the mirror is without a frame, a solid plywood will be screwed onto the rail, its dimensions can be slightly less than the mirror. The mirror is glued with mirror glue, in addition, it is necessary to stick two bilateral scotch strips to fix it until the glue is grabbed. As an additional support for the mirror, you can install a narrow shelf right below it. If such a design does not seem reliable, you can attach it using a special fastener.

Another option is a frame as for a photo. It is made of a textured board, carefully polished and covered with varnish, or from a platband.

Thus, you can summarize the basic principles of wall-mounted hangers in the hallway, and vary them at their own wishes. Reiki can be replaced with a solid shield, which can not only paint, but also bold (leather, cloth, apply decoupage techniques). A little imagination, and in the hallway there will be an absolutely original, unique work.

Hinged model

Complete the functions of the hangers in the hallway and a small roomy locker, you can, developing a product with several (1-3) photo based on the photo and hooks for clothes, thus obtaining wall accessories.

For this, all with the same already named tool set, you need to prepare several strong good quality boards, with processing. The boards from the old furniture are suitable - because the tree retains strength for many years, and furniture parts are also qualitatively processed.

Thinking the size and number of shelves, you can start work. In the photo with drawings, it is reflected as precisely and in what order the assembly occurs. Cutting the boards of the desired size, you can start an assembly by attaching the side panels to the bottom shelf. Boards are attached to the back side of the sidewalls, the amount depends on their width. The height of them can be calculated, based on how much the shelves are planned, what a height will be.

Mondering that the hanger must withstand not only an indefinite amount of clothing, but everything that is located on these shelves must necessarily apply furniture corners, strengthen the design, without fearing to move.

How to screw up, described above, and in this model hangers the reliability of all fixings is particularly relevant. The boards that will be screwed, which will become shelves, and to the bottom of the frame - another strong plank, which will not allow things to fall out. And screwed on it (after painting, varnishing and other finishing works) hooks.

How to hang

The design is attached by reliable screws directly to the wall. As an option - attach 2-4 ears for mounted locks, and hang the product on them (a solid fastener is screwed into the wall on the dowel). The ears are made from alloy steel, and, carefully attaching them to the hanger, you can be calm, it will not fall soon.

Creative ideas

In fact, starting to look at things from the point of view of their additional non-traditional functionality, it is easy to make outdoor and wall hangers from anything, literally from what is lying without affairs and dust in the storage rooms.

Having treated the branch selected in the forest, you can fix it on the wall, and supplying semi-healthy hooks, use as a hanger. The set of pins with branches attached on the shelf can also serve as a hanger in the hallway, and the shoulders can be used. Old cutlery can also be turned into stylish hooks. It is worth trying, there is nothing more fascinating than without extent to create a comfortable space around him with your own hands.

The first impression of the owner of the apartment begins with the hallway. There is no possibility to place overall furniture. Quite a wall-mounted hanger. From its design and material from which it is made, the ease of use and durability depends.

Depending on the number of family members, the wall hanger in the hallway can be large or small, one or two walls. Double hanger for two walls is called angular. The disadvantage of such hangers is one: In order to install it, it is necessary to drill the walls and install a dowel. To do this, you need a perforator or you need to invite a specialist.

What are wall-mounted hangers

We define immediately, wall hangers are those that hang on the wall. Make them from various materials:

wood;
dSP plates, MDF;
metal;
combined.

Furniture styles in the interior a lot. Since the majority of the population does not live in the royal chambers, the styles are most suitable for the mass consumer:

functionalism
minimalism,
country
high tech,
ethnic.

If the hallway is a small wall hanger solves a lot of problems. Additionally, the hangers are equipped with couches, mirrors, shelves. Depending on the height of the room, the structural elements are located horizontally or vertically.

In small halls, you can choose a construction that occupies the minimum space. Constructively perform them assembly or collapsible. Prefabricated designs are collected in the enterprise and sold in the finished form. It is possible to attribute wooden from the array and metal. Collapsible must be assembled at home from purchased parts.

Tip: Pick up the apartment or hallway

Hangers from the massif

For wooden hangers, various breeds of wood are used in the hallway: oak, beech, ash, birch, spruce, pine. Hooks are wooden or metal. Modern trees for wood allow the wood to give wood any shades.

Design options are with a shelf for storing hats or without it. Big hangers can be equipped with mirrors, shelves, storage boxes of trivia, shoes.

Wooden products are always expensive. Moreover, it should be noted that soft wood pine or spruce can cost more oak or beech. This is not connected with the price of the source material, but with the difficulties of technological processing of the surface. Soft wood ate is processed bad, after grinding remains risks from abrasive. The array is covered with varnishes, wax or just paint. The advantages of array products are their environmental friendliness and a long service.

Hangers from chipboard chipboard, LDSP, MDF

Wood-chipboard and MDF plates in furniture production occupy a strong position. They are inexpensive, covered with laminated films under valuable wood, they do not cord, they keep the geometric dimensions of the entire period of operation.

MDF is a finely dispersed fraction of fibreboard. They are perfectly milling, covered with paints, varnishes, films for valuable wood. According to its consumer qualities, MDF is superior to chipboard, but they are more expensive.

Plates from chipboard, LDSP and MDF are sold in a finished form to work for homemade masters. It is necessary only after cutting the ends with laminate or special plastic overlays.

Metal

The design of wall-mounted wooden hangers give the hallway novelty and originality. It can be done in different versions: with a shelf for hats or without, with a decorative grid, separating clothing from the wall, with different decorative crochets.

However, for the completeness of the painting for metal hangers, additional products are needed, made by forging: Stand for shoes, mirror, keystitch and others.

Combined

All well-known materials are used for combined hangers. There are no restrictions here. Appearance depend on the imagination of the designer. The choice of materials for the manufacture of wall hangers is huge.

Pay attention to the hooks. Preference should be given metal. In winter, heavy clothing will hang on the hooks: coats, dublinka, jackets. Further operation of furniture will depend on their strength.

Color selection

Since there are no windows in the hallway, the choice of color solutions of furniture plays a huge role. Keep in mind that white color expands the space, and the dark furniture are narrowing. Choose wall hangers of bright shades. If the hallway is connected to other rooms, then in this case the style of the hallway should harmonize with a common room.

How to choose a wall hanger

You must choose from:

the number of family members;
design;
financial opportunities;
national team or inappropriate design.

Before buying, decide on additional accessories:

shoe sections;
shelves;
mounted or floor drawers;
shoes;
mirrors.

The leaders of the production of this type of furniture are Ikea and Lerua.

IKEA In addition to Wall-mounted hangers, the assembly offers hundreds of hook options for clothes from various materials, ranging from plastics and ending with metal hooks anodized under gold or silver.

Not lagged behind its competitor and Lerua Merlen. The main thing is not to be confused among hundreds of hook options for clothes. Both firms apply modern MDF materials, chipboard, metal, plastic, glass.

How to make a wall hanger yourself

In order not to lose in vain time and not to overestimate your strength, let's say right away, which can be done independently, inexpensively and with a minimum of tools, but what is not. Make a hanger from the wood massif, without having a specialized tool and skills of work, it is impossible. Buy circular saw, milling machine, grinding machine and other tools does not make sense. For this money you can buy several products.

Really, you can make a wall hanger from wrought elements plus chipboard or MDF panels. And you can also use laminated chipboard.

Procedure

Select photos from the Internet and make your design. Make a sketch of future hangers with all sizes.
Provide vertical or horizontal strips separating clothing from the wall in order not to wipe it.
Select the necessary texture of the chipboard of the laminated film and order the cutting in its size in the construction hypermarket.
Ginger and creek the ends with a special film on PVA glue.
If there are connections on screws or furniture screeds, select special plastic plugs to hide them.
Choose hooks with lots of screws for fastening than two. Consider the chipboard is chips and sawdust. Before screwing the screws, drill a hole with a diameter of 1 mm and a few drops of PVA glue drops into it.
The same applies to the walls on the wall. See that screws do not get out on the front side.
Drill in the wall by a perforator hole for plastic dowels and drive them into the wall.
Set hooks or hinges to which wall hanger will be installed.
Install the hanger in place.