Make a garden shower. Summer shower for giving: versions and materials. Construction of a wooden cabin for the country soul with their own hands

The best holiday after tense work on its summer cottage is a pleasant, warm, relaxing shower, which not only affects soothing, but also remove the nervous tension accumulated over the whole day.

To install the soul, use epoxy resin for the manufacture of which is used by special fillers for resins.

Therefore, many gardeners equip their sectors with summer shower cabins.

Summer shower on your cottage

The shower cabin outdoors is perhaps one of the most important buildings on the site. With it, it is not only possible to wash your body after a whole day of work on its site, but also refresh yourself in the summer heat.

Before mounting the shower cabin on its site, it is necessary to optimally choose a place for this. The shower must be on a small distance from the main structure, most often behind the house.

After the owner of the site decided on the shower site and the size of the shower cabin, it can start mounting. This room should be at least 1 sq.m. By area, but preferably a little larger.

If a shower fabric is planned, in order to undress and rave dry things, the construction area is doubled. The height of the structure is usually approximately 2.5 meters.

In general, the sizes of our cabin are equal to 1.0x2.0x2.5 m, this is the optimal option. If the installation of the cab is planned from a tree, then it is necessary to mount a frame using a tree bars or metal corners.

Walls in the shower, for the best ventilation method must retreat from the ceiling and floor for twenty centimeters. They can be constructed from materials remaining after the main construction of a nursery house.

Water shower equipment

When installing the shower cabin on its summer cottage, the owner must necessarily think in advance how to equip the supply and removal of water. Since the removal and supply system is mounted at the time of bookmark the foundation of the future shower cabin.

Water in the shower room is very often served from the source at a remote distance. Such a source can serve as a well, drilled on a plot or standard water supply.

Nowadays, due to the presence of plastic pipes of a small diameter, combine the cabin with the main source of water supply, will not be much difficult. What is beneficial to these pipes, they are more durable and are not covered with rust and various erosions, like metal pipes.

They are sold in the bays, and there are no special troubles during the laying of a pipe for water supply, it is necessary to provide only a connection with the main source, which can be done with a small, rubber piece of hose.

You can easily connect a plastic tube with a cumulative shower tank. The advantage of such pipes is that if they were mounted not by capital, they can be easily removed from the site for the winter period.

Drain of water in the shower

Water removal after washing, can be made in various ways. Some owners of country sites, absolutely do not drain the water.

One of the most normal ways to make a watering of water to centralized sewer, but, unfortunately, such an opportunity is not every owner of the country area.

The best way, of course, remains the waste and drainage pit. It does not require much costs, and allows wastewater to go deep into the ground. A hole for drainage waters can be placed under the shower, or in close proximity to it.

It turns out in a depth of no more than 50-60 cm, the size of the sides is 1.0x1.0 m. After the pit is dug, the soil in it is tightly trambed and covered with rubble or broken bricks.

On top of a pitted pit, put a plastic, steel or wooden pallet.

After that, mounted a shower cabin. If the wedding pit is near, it is best to make a removal of a sewer pipe from plastic.

Photo of ideas how to make a summer shower in the country

The water outdoor procedures are very useful, so many relaxation adherents and hardening make a decision to make a summer shower for the shower in the country with their own hands or at least install the finished cabin on the site. This article will help to understand the features of the design, correctly select the size and installation location, make a preliminary scheme and without errors to perform all stages of construction.

Types of autonomous toilets. Choosing a place to build a toilet in the country area

If the construction of a capital soul is supposed to have their own hands from the brick, it is advisable to use the tape type of foundation. A trench is formed around the perimeter of the future building. The optimal depth is 0.5 m. Next formwork is performed. At the bottom of the trench, it is necessary to form a sand-gravel pillow with a thickness of 0.1 m. After that, the reinforcement is stacked and the pouring concrete is carried out. It is necessary to make it so that in the finished form of the foundation towered above the ground level by about 0.1 m.

When the base is completely freezing and dried, it will be possible to start building the sewer system.

How to organize a drain system in the soul in the country with your own hands

There are several ways to organize the waste system in the shower. The choice of construction technology depends on several factors:

• type of soil on the plot;
• type of foundation;
• the number of people living in the house.

If a monolithic plate is used as a foundation for the summer soul, a monolithic plate is used in the country, then before performing the fill, the system of plastic pipes with the knee should be laid. The stove is formed so that from all sides there was a bias toward the drain hole. The sewer tube is outlined outside the shower and connects to the total wastewater system. You can bring the drainage to the drainage well.

Helpful advice! For the construction of a similar sewage to the cabin installed on the foundation of another type, it is not necessary to fill the floors with concrete. It is enough to buy a summer shower for cottage with a pallet made from acrylic. This element will perform the floor function.

With the connection to the sewer system - the optimal option for a large family, since the pit will not be able to accommodate the volume of the effluent, which will be formed during operation. If the design is calculated for 1-2 people, there will be a plum directly under the booth. But this type of system is suitable for areas with a loose type of soil when the shower is installed on a column or pile foundation. This option can also be used on a belt base.

First you need to remove the soil layer with a depth of 0.5 m. Formed recess on half of its height, filled with gravel or stone. The remaining part falls asleep by rubble with a fine fraction. After the design of the cabin is assembled, a pallet made in the form of a wooden lattice is installed on the rubble layer. The system is arranged in such a way that the wastewater passed through the layers of drainage and gradually absorbed into the soil.

Sometimes the owners of country sites bring the waste pipe into the garden, which cannot be called a good solution. If you still resort to such a method, it is desirable that the place where the water is merged, was well warmed by the sun. Otherwise, the liquid will accumulate, and the swamp around the shower is formed, sising mosquitoes.

Cabinet manufacturing for summer soul: photo and construction technology

For the construction of a booth for a homemade soul, any blowed materials can be used.

For these purposes, it will be suitable:

• wood;
• polycarbonate;
• professional flooring;
• brick.

Each type of material has its own advantages, features and properties.

How to build a shower in the country do it yourself: Economy Cabin

There is a small trick that will help achieve savings in the process of building a shower house. To reduce costs, it suffices to use one of the deaf walls of the building as a side for the booth.

Before building a summer shower of a budget type, it is necessary to fix on the wall a container for the water of a small size, equipped with watering can. Here you can install the accompanying comfort elements, such as hooks for clothes, shelves, etc. At the top of the future design there is a partition. It is fixed on the wall of the building. A tarp or film (necessarily opaque) can be used as the entrance door. The curtain is suspended with rings.

The floor is shuting up so that the drains get out as far as possible from the foundation part of the house. To do this, the platform is concreted or you can do the installation of the pallet made from acrylic.

Helpful advice! If you use the internal angle of a structure having a M-shaped form, you can generally avoid the construction of the drivers of the booth. Their function will perform the walls of the building.

Construction of a wooden cabin for the country soul with their own hands

The most common variant of the summer soul is a cabin made in the form of a wooden house. This type of building is considered one of the most affordable in the price. Wood is easy to handle. At the same time, it perfectly keeps heat, which is an undoubted advantage if the souls will be used in cold weather.

For the construction of a summer soul in a private house, it is advisable to use a wooden timber. For the manufacture of corner racks of the cabin, a material that has a sectional size of 10x10 cm is required. At the top of the shower, a tank is installed, calculated on 200 liters of water, so the timber must be quite thick to withstand a similar weight load.

To hang the door, you will need to install two more additional racks in front of the cabin. These elements are placed between corner racks. For their manufacture, you can take a bar with a size of 5x5 cm.

To form a small block angle for a single roof of the cabin, it is recommended to install the front corner racks 0.2 m higher than the rear. This will not be required if the square shape tank is used as a container. In this case, the racks are mounted at one level.

All supports are attached to the wooden frame of the lower strapping. For fixing it is necessary to use hardware and metal corners. In the upper part of the design, the binding is made in the same way. To stronger struts stronger, you can use spacers. On the upper strapping of the frame of the cabin, the base is formed for installation of the container. At the same time, it is necessary to read not only the size, but also the shape of the tank.

To cover the framework of the structure, you can use a 2 cm thick board. Such material is suitable for the manufacture of the door. You should lay the boards in one row and knock them together with two jumpers. To prevent the door to prevent the design, the design can be strengthened, using a long rail. The door frame for the country's summer soul is made of boards, the thickness of which is 4 cm. It is recommended that the screws are recommended as a fastener.

When the cabin is fully ready, it can be opened with a color varnishing composition. From the inside, the entrance is enhanced by the film, otherwise the doors will swell from moisture.

Helpful advice! Often, a large soul barrel is used for the cottage. Having installed the design of the watering can, you can get a budget version of the wooden cabin.

Polycarbonate garden soul manufacturing technology

Since wood is subject to deformation changes under the influence of moisture, many land owners are thinking about how to make souls in the country with their own hands from more practical and resistant materials, such as polycarbonate. The frame of the cabin is manufactured in the same way as in the case of a wooden shower, but a metal profile must be used as a material. The optimal section size is 4x6 cm.

The frame of the cabin is formed using racks and jumpers between them. In this case, metal elements are used, so the welding machine will be required for their bond. Moreover, the order of assembly can be performed in several ways. In the first case, the frame side is welded separately, after which it is installed on the base and is attached by means of anchor bolts. The second way implies concreting racks during the fill of the foundation. Then the impunity is formed, the struts are attached.

It is desirable to use a sheet material with a thickness of 1 cm. On a metal frame, it is fixed in a metal frame with hardware, which must have sealing gaskets.

Installing the tank and the features of the construction of the soul at the cottage heated with their own hands

At the last stage of the construction of the soul, the tank is installed. Capacity can be made independently using any container made of stainless steel or plastic. To do this, in the bottom, it is necessary to form a hole, the diameter of which is 1.5 cm. To it, with the help of nuts, the segment of a pipe is mounted, having a thread from two sides. The length of this element should be 30 cm.

In the roof of the cabin in the center you need to make a hole where the nozzle will be inserted. After installing the tank on the free end, the crane and watering can be screwed up, made of plastic. Then the container is firmly fixed on the frame of the frame side of the cabin, filled with water and covered with a lid.

To create a summer soul with heating for giving, it is sufficient to install the heating element in the tank. Of course, the natural energy of the Sun can be used to heat the water. In this case, electricity costs will be absent. However, the sun's rays are not able to heat the large amount of fluid. In addition, not every region has the necessary climatic conditions.

In the network you can find a variety of schemes needed to connect the summer shower for ha heated to electricity. The advantage of these devices is that the water warms up in the tank quite quickly, regardless of the time of day and weather on the street. At the same time, a person can configure the temperature regime itself. If we fix a piece of foam, the warmest water will go to the hose. For the same reason, the fence of the fluid is carried out from the upper tank zone.

Helpful advice! To speed up the heating process of fluid, can be added to the coach of the coil.

Is it possible to buy a summer shower for cottage cheap: prices for ready-made designs

To simplify the technology of construction, you can buy a summer shower in the finished form and install it on a prepared basis. The cost of cabins is diverse and it depends on various factors.

The following points affect the product of the products:

• manufacturing material;
• modification (changing room);
• form of water tank (in the form of barrels, square tank);
• equipment (presence of heating element, tank, temperature sensor, etc.);
• capacity of the tank;

• the material from which the water container is made.

Middle Rates for Ready Designs

Name	price, rub.
Metal frame and PVC fabric
Sad shower
Garden shower with water heater
Garden shower with water heater and changing room
Construction of polycarbonate
Cabin with a tank at 130 l
Cabin with a tank for 200 liters
Cabin with a tank at 130 liters heated

A wide variety of materials suitable for construction, as well as manufacturing technologies allow any dacket to get a comfortable and convenient shower in the country. Moreover, you can make a booth independently from the remedies or to purchase it in a ready-made form in a specialized store.

The owners of country sites are trying to bring water to the house and equip elementary amenities. You can build a summer shower in the country with your own hands, both temporary and capital - the type of future structure is selected depending on individual needs.

Before building the souls in the country with their own hands, it is necessary to competently perform the design, determine the placement of the future structure, choose materials. The room should be stiff, most comfortable and convenient for use.

Choosing a place

In order to provide a quick water drain, the shower is optimally installed on a flat or slightly sublime platform. Do not choose a plot located in a strong lowline or in the pit.

To avoid water stagnation, choose the right place to build a summer soul

The optimal for the summer soul will be an open area, well illuminated by the Sun, which is located in some remoteness from other buildings. In this case, the barrel will be naturally heated under the sun, providing the flow of warm water. This condition can be neglected only if the construction of the shower room with heating water is planned.

At the same time, the site where construction will be conducted should not be too far from the house - after water procedures, it is desirable to get from the shower to the warm room as soon as possible.

Calculation of sizes

During the construction of the summer soul, the following parameters are used standard:

1. height - 200-300 cm;
2. length - 190 cm;
3. width - 140 cm.

An example of a summer soul drawing

The specified dimensions are very convenient to the fact that, taking into account the thickness of the walls, the construction will eventually be released with an area of \u200b\u200b200x150 cm - this is a fully utmost option when using standard sizes. As a result, 100x100 cm will be allocated under the shower cabin, and 600x400 cm under the dressing room.

Required tools and materials

The following tools will be needed:

• roulette;
• corner;
• level;
• a hammer.

In addition, you need to stock up the nails and the Motka of the Beach. Separately, you need to buy a tank, as well as pipes, a couple of cranes and a divider for the shower. Brick, iron or plastic sheets, wooden boards, for construction of a frame - pipes are suitable as building materials for building a cabin.

Tools required for building a soul in the country

For the foundation and construction of brickwork, a certain amount of cement, sand and concrete will be required, and for the final finishes - insulating materials, paint, plaster, hooks under the clothes, shelves for bathroom facilities and other accessories.

Options for giving shower structures

The easiest option for the cottage is a compact portable shower that is suitable for one-time visa of water procedures, has a standard volume of 20 liters and is designed for water supply for 10 minutes. The principle of operation comes down to filling the water tank and the subsequent heating in the sun, after which the portable shower is attached to a height of 2 meters and is ready for operation.

Portable shower

A simple design also has an open shower, the installation process of which is reduced to the following actions:

1. fastening to the water pipe branch wall;
2. connection of the pipe and watering can with the hose;
3. fixation of the holder of watering can
4. installing the screen.

A common option for the country area is the so-called domestic with a shower, the design of which involves the presence of a solid modular container or a frame-collapsible block.

Stationary summer soul options for giving

Installation of this design is quite simple - the area marking is made, the upper ball of the soil is removed and smoothed, the pillow of sand with gravel, on top of which boards are stacked. At the soil prepared in this way, the block assembled at the spot or the finished design is established.

Of course, the most common will be stationary souls, but for its construction it will take more effort and time.

Preparation of the basis

The frame structure is erected much easier than the capital construction - depending on the type of construction type, the stages of preparation of the construction site will differ.

For a temporary design, it is enough to simply remove the top layer of the soil from the site 10-15 cm to align it and then fall asleep with sand.

For the cottage capital soul, the foundation is required, the depth of which is determined by the materials that are used for its construction. For example, for a brick soul there will be quite enough foundation, the depth of which will reach 30 cm.

Foundation for the construction of a capital summer soul

The foundation is laid in the following sequence:

• through the outdoor corners of the future soul, pegs are clogged;
• the cord is stretched around the perimeter;
• prepared the place for the pipes (there is a log or a branch, wrapped in rubberoid);
• concrete solution poured.

Tip! Extend the period of operation of the soul will allow the formwork equipment - the level of all foundation is recommended to increase by 10 cm, lifting it over the ground using boards, strengthened stakes and struts.

Equipment of drain pit

The volume of the pits is usually more than 2 cube. m, while its walls must be strengthened in order to avoid possible scree. The plums are located a few meters from the shower, but not under the structure itself and not at its walls - this in the future will lead to the destruction of the foundation, as well as to the emergence of unwanted smells.

Example of drain pit equipment for summer soul

The stock must be laid with a waterproof layer - the runneroid, hydrohoteloisol, PVC film or a concrete screed (reinforced with a metal grid).

Attention! A widespread error is the use of clay as an insulating material that is blurred and soon clogs the drainage database.

Mounting frame for temporary shower

If a brickwork is performed for the capital construction, the temporary is usually installed frame: metal or wooden. In the latter case, the tree should be treated with special impregnations that protect it from insects and moisture, preventing the formation of fungus and mold.

Wooden frame for summer soul

1. Marking is done - denotes a rectangle directly on Earth, the sides of which correspond to the size of the future dacha soul.
2. The bars are installed from the tree, the width of which reaches up to 10 cm.
3. Pulling is performed - starting from above the design is securely bolted, after which the bars are connected and the bases of shower walls.
4. Walls are equipped, for the construction of which you can use both boards and slate or plastic panel.
5. Pipe wiring is performed - the water supply is installed so that the output of the pipe under the shower hose was higher than the head level (this will provide the necessary pressure to move the water). The flow is made to the sump or in a specially equipped septic tank.
6. The tank is installed - a thread is done, a crane is made with an appropriate nozzle, after which the barrel rises upstairs and fixes.

As a tank for the summer soul, a plastic container is suitable, which can be purchased in a specialized store, or another existing barrel. It is desirable that it be a flat and commensurate area of \u200b\u200bthe structure so that the weight is evenly distributed on the carrying structure. Its volume is selected at the rate of 40 liters per family member, but at the same time the barrel should not be too heavy - its extreme volume is no more than 200 liters!

Tank for heating water from the sun

Tip! In order for the owner of the cottage to do not occur every time on its own to wear water into the tank, you can equip it with automatic filling.

Lighting and Ventilation of the Holy Soul

By independently making wiring, it is important to follow all the rules of the electrical installation and adhere to safety. Separately due to high humidity, take care of the insulation of the wiring.

Summer Ventilation Window

The inner shower finish should be performed from moisture-resistant materials: plastic panels, linoleum segments, oilcloth, etc. If wood is used, each separately taken board is covered with hot oil.

The concrete floor is usually covered with plastic lattices or wood, rubber mats are spilled on top. It is fairly convenient to equip directly into the shower small locker room. In order for it to do not fall into it, the floors in it climb a couple of centimeters slightly - it is easy to achieve, additionally putting the pallet.

Summer Soul Interior

As for the outer finish, the similar materials will be harmoniously, which are already used to design a country house and other buildings available on the site.

To use the soul not only in the summer, but at the colder time of the year, it is recommended to be insulated with the help of polystyrene foam, which is stacked into the inner space and on top of the PVC film. Walls usually face either plastering, weed with clapboard or siding.

How to build a summer shower at the cottage: video

Types of summer soul: photo

Summer is a great time for a country rest. It may darken it. No soul, as a person, regardless of whether it works or rests, it is necessary to produce water procedures.

If the cottage is used only in the summer, then the shower is easiest to organize on the territory of the site. You can make a mobile shower, or build a solid economic building.

Portable summer souls

In stores you can find a foot shower. To operate it, it is not necessary to build anything. As a rule, it is necessary to use it only a small water tank.

The existing hose is lowered into the container, which is connected to the pump. He resembles a small rug. Water comes out through the hose with a watering can, and that she goes, a person needs to be just staring in one place.

This device is simply indispensable, since it is suitable not only for giving, but also for picnics, you can take with you hiking.

With its help, water procedures can be carried out not only on the street, but also in the house when it's very cool on the street.

To do this, you just need to put the basin and wash. Another advantage of the mobile soul is an independent water temperature adjustment. Such souls in the country just do not replace.

Stationary souls

Many dacities are interested in how to make a stationary shower. This option is quite expensive compared to the first. However, you will serve you for many years.

Before starting construction, it is necessary to consider where water will merge from it. Well, when there is an antiseptic on the plot. It can be drained to the soul.

If it is absent, then you need to make a hole, fall asleep with a clamzite. The family needs a yam in size 60x60x60 cm.

If sand prevails in the soil, the root walls will have to strengthen so that they do not crumble. For this, a metal grid or boards that are no longer needed are suitable.

Base under the shower

As a rule, the shower construction is little weighs. Therefore, it makes no sense to make a foundation under it, it can be replaced by blocks. They are aligned to one level so that the design stood smoothly.

It is much cheaper than the foundation, and it takes a lot less time on construction, since the foundation should dry, and you can immediately build construction at the blocks.

Blocks should be exhibited 20 cm from the ground, it is necessary so that the tree does not rot.

In the event that you are going to do the design of metal, then the blocks can not be aligned in terms of 20 cm. Such a frame can be installed on the usual pavement tile.

Building

There are two types of buildings. The first when the construction is divided into several parts. In one part there is a shower, in another dressing room or the technical room where the boiler is installed.

Note!

The second type is a simple shower with a curtain, where there will be only water procedures. Therefore, the soul sizes are calculated from what kind of construction is planned.

Types of carcass

Metal. The frame can be performed from a profiled pipe, 3 mm in size. Welding apparatus is needed for work.

The joints of the pipes are best cooking, so the design will be stronger. If the device is missing, then the joints can be copped with special bolts.

Wood. For construction, the timber is needed. Typically use a timing of 50x50 mm. Before starting construction, you need to draw a shower drawing at the cottage.

Touching soul

After the framework elevated, the shower must be covered with the material. There are no specific standards for the material. Everyone chooses, by his pocket.

We highlight the most popular materials:

• oilcloth;
• the cloth;
• wood;
• slate;
• polycarbonate.

Water tank

As a tank, you can use absolutely any container. Basically, these are metal or plastic barrels. They can be purchased in any construction, dacha stores.

Note!

When choosing, consider the area of \u200b\u200bresidence. For the southern cities, any capacity is suitable, but for the northern regions only metallic, as it heats up faster.

Pallet for shower

The pallet is best to purchase it ready, since it will be a plux in it, which will directly merge into the pit. Pallet is made of plastic or metal. Metal will serve much longer, so it is advisable to choose it.

Make a summer shower in the country is not so difficult. The main thing is to find out to design and calculate the amount of material required in advance.

For clarity, you can consider the photo of the summer soul in the country of your own hands. With him your holiday will be comfortable and enjoyable.

Photo of the soul in the country do it yourself

Note!

The construction of a summer soul for giving is not without any questions related to the choice of material and determining the size of the structure. In addition, I want the construction to be heated. It will give the opportunity to swim in the cold days when water in the tank will not have time to warm up from the sun. An important issue is the organization of drainage and drain of dirty water. Today we will look at how to build a summer shower with your own hands, and we will try to affect all the questions you are interested in.

The country's souls are so simple that it does not require a detailed scheme. Usually maintain the standard sizes of the cabin 1000x1000x2200 mm. It is impossible to build below the booth, as a part of the height takes the wooden pallet, plus the watering can above his head. But the width and depth of the structure is desirable individually pick up the hosts for the body. For example, a fat person in a small booth will be closely, so the sizes will have to increase.

A simple summer shower drawing for giving

If you decide to enhance the construction, build a pre-banker with a locker room, install shops and a table in it, there will already be drawings here. Draw what you want to build, specify all sizes. By drawing up a detailed scheme, think over the following points:

Wooden shower cabin

The construction of a tree cabin is the most common option due to the simplicity of its construction. Tree - environmentally friendly material, easy to handle. The only drawback is the exposure of moisture and bugs, so it requires additional processing. To build a wooden shower for summer cottages, you will need boards and a bar, preferably, of coniferous trees. You can, of course, use oak or larch. Material from these tree breeds more durable, but it is harder to process. Deciding with the material, getting started:

1. Since we build a wooden shower, the framework will be made of wood. The main load on the rack will create a water tank. If its volume is about 200 liters, then the main racks should be installed from a bar with a cross section of 100x100 mm. To mount the door, install extra racks from the bar with a cross section of 50x50 mm. The distance between them is equal to the width of the doors themselves with the door frame.
2. Under all vertical racks, dig a pits with a depth of 80 mm. Pour holes to fall asleep 100 mm layer of rubble with sand.
3. So that the tree is less rotten in the ground, lubricate the edges of the bar with bitumen or machine oil. Wrap over two layers of rubberoid on top. Insert the racks into the pits, align them with a plumb and concrete.
   
4. Another method of extending the service life of the racks is concreting metal sleeves. They can be made of segments of a metal pipe with a diameter of 100 mm. When concrete freezes, the edges of the square bar are engaged by an ax in the size of the inner diameter of the pipes and install them into the concuted bushings. Under the door racks, similarly balance the sleeves from the pipe of smaller diameter.
5. By installing vertical racks, front door. Make 100 mm above the rear. The height difference will help to build a single roof.
6. The exhibited racks connect around the perimeter from below and on top of horizontal jumpers, securing them with bolts. If you plan to make the floor in the form of a wooden grid, the lower jumpers enhance with metal mounting corners. The jumpers will be supports under lags and must withstand human weight.
7. Now it will be necessary to make a frame under a tank of wooden jumpers, fixed from the top of the frame. A tank filled with water from any material has an impressive weight, so the frame under it must be done strong.

   

   Flat water tank for water is installed on the roof of the shower

8. Boca skeleton carcass in a polished board. Make a door from a board with a thickness of 20-25 mm. Cut it with the necessary length, put in a row and sew crossbars. From the board with a thickness of 40-50 mm, run down the door frame and lock the door with her loops. Now all this construction can be mounted with bolts to the door racks.
9. Finished cabin process the antiseptic and cover with oil or varnish. The door from the inside take the film so that water does not fall on it.

Wooden Cabinets for Summer Soul

Polycarbonate cabin

Polycarbonate Cabin is easier than wood, but you will need welding experience. The fact is that for polycarbonate it is necessary to weld the frame from the metal profile. For the racks, the profile will take a cross section of 40x60 mm, and for the strapping you can use a smaller cross section. The use of a carcass made of wood for polycarbonate is not desirable, since both material have the "Play" property from changing weather conditions. From this polycarbonate sheets can be deformed.

The process of manufacturing a metal frame for polycarbonate is similar to a wooden structure. Basic racks concrete, and then weld the upper and lower jumpers. In the middle of the frame, it is necessary to make three jumpers so that polycarbonate sheets do not be bombed. The fourth is not needed. She will interfere with the doors. Top weld the frame under the tank. Make a frame under the door from the profile with a cross section of 20x20 mm and lock it with loops to the rack. The whole design is painted with waterproof paint.

For the trim, use opaque cellular sheets of polycarbonate, 6-10 mm thick. Large sheet cut into fragments on the size of the cabin with a disk saw. The resulting polycarbonate plates lock to the frame of self-threads with thermoshaba. Door, too, cover the sheet of polycarbonate. To the frame, screw the handle and the scoring with bolts.

Polycarbonate Soul Option with Pre-Ban

Shower

Cabina from professional flooring

A good option for giving will be built a booth of a professional flooring. Lightweight, durable and durable material will last for many years. For metal products, both metal and wooden frame are suitable for metal, but necessarily with additional transverse crossbars. Sheets are soft, and the additional emphasis does not prevent them. Any of carcases for metal products we build similarly to the above options. The door frame in any case is welded from a metal profile.

The fastening of the professional flooring is performed by galvanized self-drawing with a sealing washer through one wave. Initially, secure the sheets of professional flooring on the side walls, then cut the door. If you need to cut the material, use scissors or a special disc with teeth on the grinder so as not to burn with a cutting of a polymer coating of a professional flooring.

Cabin of bricks

Construction At the cottage of the brick cabin requires the construction of the foundation. To do this, it is enough to dig up around the perimeter of the future structure a trench of 200 mm wide and a depth of 400 mm. Trench plump a brick fight and fill with liquid concrete so that he leaked among it. A week after pouring the concrete, start the brickwork on the cement solution. Do not forget to install the box for the door. The door itself can be made of wood or cook the frame from the profile and sew its sheet of professional flooring. On the last masonry, impenet the wooden bars across the structure, preferably in brick thickness. They will lay roof and mount the tank.

Install the roof and tank

The roof material will need hard. Slate or professional flooring is well. Securing the roofing material, drill a hole in the center of the roof. Install the tank from above so that the tube feeds passes into the hole. Screw the crane and watering can on the tube.

The optimal tank capacity for the country soul is 200 liters. In the store you can buy a plastic or galvanized tank or make it yourself, welding stainless steel. Baku will serve any container with the neck for filling water. To make a shower for giving water heated, mone into a metal tan tank, 2 kW. Top paint with black paint container. Dark color attracts the sun's rays, and the water will heat up faster.

Diagram of the device tank for summer soul with heated

If you install in the cottage in the Cabinet of wood titanium, then besides hot water, it is heated. Then you will need to install a number of second tank with cold water.

Floor and drainage

Floor and drainage shower for giving can be made in two ways:

Summer shower in the country house

If there is a free space, the country's shower can be built in the house. To do this, it is better to purchase a shower in the store. In the concrete floor, make a depression and install the acrylic pallet according to the product instructions. Siphon on the pallet Connect the corrugated hose to sewage. The jokes of the adjustment of the pallet to the floor close the sealant. Next, according to the instructions, collect the framework from the profile, set the doors, let down the cold and hot water from the boiler.

As you can see, build a summer shower with your own hands in the country can be almost from any material. The main thing is to prepare drawings, material, tools and show the desire.

In contact with