Decorative castles made of stone with their own hands. A small castle with your own hands. Draw billets towers

How to make a unique site or garden - the JB of this dreams of many owners. Decorate your own estate, the country, the courtyard, many adore, but not all have extra money, which could be spent on decorative figures. But this is not a problem for those who at least something can do their own hands.

It does not even need special costs.

So, for example, the fabulous kingdom on the garden site will be a good gift and small, and adult dreamers.

Even built at the dacha mini castle will give the plot of mysteriousness.

Mini-locks into the courtyard or for the garden are obtained by volume large enough, and it is completely difficult to build it.

You can try to perform some parts of the castle separately, then in any part of the garden, it was possible to collect it from the finished elements as cubes.

Design Example for the construction of the castle in the country

it is easy to disassemble. To reduce the consumption of the solution, you can put banks or bottles inside the cylinder, but the thickness of the solution around the ballast should be at least 5 cm.

The solution for infusion should be sufficiently thick. He needs to give a few hours to grab to such a state so that when removing the formwork did not crumble. It is necessary to choose the height of the cylindrical formwork: it should be approximately equal to the height of the tower, with a smaller size of the formwork, it will be necessary to disassemble and collect a little higher than the lower part already the climbing.

Make a castle for giving just if you have a couple of "golden hands".

The main material - sand and cement for longevity composition. 2 parts of sand and 1 part of cement.

Elements of typical design.

Let's start with the turrets.

The cylinder of the desired radius is collapsed from the iron sheet (I have about 2-30 cm). The cylinder is fixed with wire or self-drawing

The inside of the cylinder is causing anything - bottles, banks - to reduce the consumption of the solution, but the thickness to the ballast should be at least 5 cm. Flit with thick solution.

We give him a few hours for setting to such a state so that when removing the formwork, it did not crumble.

Raw, a little clutched solution immediately begin to cut.

The cutting technology is the same as the sandplaes. For cutting apply a set of tools available in each.

Do not forget to make the windows, loopholes, skinning the desired deepening knife.

Poured the form with a solution and, after partial setting, gently remove the formwork of the cylinder and make the desired number of windows, teeth - as a fantasy tells.

The roof can be made of tin cones, it is possible to use this tin cone as a form for pouring the solution. After complete gripping, carefully dispel our roof from the form. Do not forget that we are still preparing separate elements of the castle. Collect all together will be later.

We proceed to the construction of the walls. Walls we will have either a serf (1) or element of the building (2).

There is no difference in their manufacture.

We collect the desired rectangle from the cooler with a width of 5 cm. We put it on a flat surface, pre-laying either the film or a piece of rubberoid so that the solution is not absorbed later.

You can put a metal arch in this frame - it will be a door or gate. Fill into a frame solution. Where it is not planned to be neither the windows nor the door can be at the bottom to plug rubber or broken bricks to save the solution.

After the solution is flooded to the desired height, you can take cute pebbles from the crushed stone and blast them at the base of the foundation so that they are flat edges over the overall plane of the solution approximately 5 mm.

Further braces are made, windows. Draw everything that prompts you fantasy. To remove the residue of the solution, I use a soft brush (probably saw in the movies as archaeologists work). In the end, you will still lie on the table about the following.

Leave the finished walls about a day on the table. When the foundation is prepared to assemble.

First, we install on a cement solution pre-applied to the foundation, for example, Tower No. 1. To the tower on the solution adds the wall number 1. Then set the tower number 2.

The castle is already starting to emerge. Azart covers you. Next, attach the wall number 2 and end with the installation of the tower No.

Assembly scheme:

When this design grabs, form a two-tie roof over the building.
So from the main basic elements, a little by changing them depending on the fantasy you can make a complex lock, such, for example.

Or completely simple:

In the garden plot, people often embody their fantasies or seen during travel, ideas spied on the Internet on different sites, and then build mountaineering, garden sculpture, original scene for flowers, wooden crafts, garden frightened and much more. This gives the cottage portion uniqueness, makes it special. It is useful to attract children and grandchildren to such activities, they really like to take part in the work and decoration of the garden.

One species of such crafts on the site is the construction of mini castles from natural materials, most often from small stones, river pebbles, large gravel. This is a very exciting occupation. It is necessary to start building such a castle from the stone from choosing a suitable place on the site. It is convenient to place it near the playground, for example, or near the place of rest of the whole family. For this, a plot of 1-2 square meters is suitable depending on the plan.

It is desirable on paper on the scale to draw a sketch of the future, determine how much it is planned to build towers, whether to connect them to the fortress wall, the arch, and sometimes they make a small ditch around the castle, through which the bridge is constructed. It is useful to search for books or on the Internet photos of real or miniature locks when developing your castle project.

Next, you need to take care of building materials, harvest cement and sand or buy a finished cement-sand mix for street work. Then bring a sufficient number of stones for construction, and they will need a lot, think about what to make roof, windows and doors in the castle. If there is a river or sea, then you can choose a round pebble of medium sizes. A large gravel of granite, limestone, sandstone is suitable. The main thing is that the stones are one species and about the same sizes.

When everything you need prepared, you can start building a mini castle. The easiest way to build a castle of three rounded towers. For this, old metal pipes with a diameter of 10-15 cm with a diameter of 10-15 cm, which are bought into the ground and poured cement for stability. You can take the segments of asbestos-cement pipes, they are also suitable for the construction of towers. It is better to make the towers of different heights. Then, starting from the bottom of the pipes, the laying of stones on the basis of cement mortar, attaching them sequentially one by one.

At that height, on which the windows in the tower are designed, the laying of stones stop, take plastic bottles of brown or green, cut out the cylinder of suitable size, draw the stack on it the window with the frame, cut the cylinder vertically with the opposite side of the side window, apply it to Pipe, continue masonry from stones to the top of the pipe. It turns out the window in the castle tower.

Then you need to make a roof for the tower. For these purposes, you can use various materials that will be at hand. It is convenient to make it from a thin tin, bent in the form of a cone, painting it with oil paint. You can cut out of the linoleum "Tiled" and nail it with cloves to a wooden frame. Another option of the manufacture of the roof is to lay a cone from the cement mortar with rectangular pieces of ceramic tiles, it is also similar to the tile.

When the castle towers are ready, they begin to build the walls that connect them, or make a fortress wall around the towers. Before the entrance often build an arch of stones. The entire inner territory of the castle is neatly falling asleep with small gravel, pre-laying the nonwoven material to prevent the growth of weeds. If desired, you can increase the castle territory, building new towers, walls, arches, bridges. To give the lock greater reliability, the figures of the dwarves, knights, princesses, decorate the walls of the dragons, hang flags and pennants.

It is important to harmoniously enter such a castle in the garden plot. If the lock acts as an independent ensemble, then low flowers or decorative herbs are planted next to it, which will give him greater naturalness. Moreover, such floral compositions can be changed annually, then mini lock will look different all the time. For this purpose, low, but spectacular annual flowers, such as pansies (viols), velvets are thincase and rejected, melts, daisy, primories. From perennials use dwarfgers, Astra Alpine, Karpathian bell.

Sometimes the mini lock from stones is simply the framing for a small flower beds, inside which the flowers are planted. This is the original flower bed in the form of a castle will decorate the lawn or the garden's front zone. Flowers are planted inside the castle fortress wall, selecting not too high compact forms of low-speed annuals.

I have a fix idea arose under the tree for garden having fun do it yourself. The choice fell on the mini lock Since it is most simple to enter at any point of the site, taking into account its geological features. Moreover, it is possible to build creatively by adding or changing its elements on the go.

The main material - sand and cement for longevity composition. Already experimenting, I stopped at the composition of 2 K 1 (i.e. 2 parts of sand and 1 part of cement). The sand is better to dry in the sun, then it is easier to mix it with cement, as well as sift to use in elements with fine detail, as the garbage can spoil the part.
Lock It has a fairly decent volume, because to build it immediately all unreal. To do this, first make individual parts of the castle, then to build it in a couple of days from cubes. Last, Third lock He was assembled in two days. The neighbors thought that he fell from the sky when they saw him.
So, consider elements of a typical design.

Let's start with the turrets. The cylinder of the desired radius is collapsed from the iron sheet (I have about 2-30 cm). The cylinder is fixed with wire or self-pressing so that it can be easily disassembled in the future. The inside of the cylinder is causing anything - bottles, banks - to reduce the consumption of the solution, but the thickness to the ballast should be at least 5 cm. Flip enough thick solution. We give him a few hours for setting to such a state so that when removing the formwork, it did not crumble. The height of the cylindrical formwork can choose themselves. It can be equal to the height of the tower, or less, but then the formwork will have to be disassembled and collecting above the lowest side.

Raw, a little clutched solution immediately begin to cut. The cutting technology is the same as the sandplaes. For cutting, apply a set of tools that are available in each. I have this screwdriver, the chisels, a medical scalpel, a hacksaw blade for metal and a variety of strips of tin for the formation of various architectural elements.
A simple cylinder is boring, here the fantasy flight begins. I make various grooves, wrapped the long strip of the cylinder with a long strip, using this strip as a guide, a screwdriver or chisel, I choose ring recesses. Then, in the lower part, you can simulate a stone masonry, destruction, chips of plaster, cracks - because the castle of ancient.

For me, the formation is the most exciting part of the process. At the same time, do not be fun to make the windows, the loopholes, the knife who smelters the desired deepening. If there is a desire to make a turret in the upper part of the tower, then we turn the cylinder with a diameter for a couple of centimeters larger and a height of 10-15 cm, insert the plastic bottle to save the solution (after a complete setting it will be removed).

Fill with a solution with a solution and after partial setting, carefully remove the formwork of the cylinder and make the desired number of windows, teeth - as a fantasy tells. Teeth I will drink with a hacksaw blade for metal - I do the cuts of the desired depth and cutting the extra solution between the propilis.

The roof can be made of tin cones, it is possible to use a tin cone as a form for filling the solution (I do that). After complete gripping, carefully dispel our roof from the form. Do not forget that we are still preparing separate elements of the castle. Collect all together will be later. So with the tower figured out. All items are ready and folded somewhere in the corner.

We proceed to the construction of the walls. Walls we will have either a serf (1) or element of the building (2).

There is no difference in their manufacture. We collect the desired rectangle from the cooler with a width of 5 cm. We put it on a flat surface (I have an old kitchen table) pre-laying either the film or a piece of rubberoid so that the solution fastened then does not absorb. You can put a metal arch in this frame - it will be a door or gate. Fill into a frame solution. Where it is not planned to be neither the windows nor the door can be at the bottom to plug rubber or broken bricks to save the solution. After the solution is flooded to the desired height, you can take cute pebbles from the crushed stone and blast them at the base of the foundation so that they are flat edges over the overall plane of the solution approximately 5 mm.
If there is no rubbank, then you can simulate the foundation after a partial setting of a sharp knife or scalpel. Pebbles can also designate future windows. Thus, your task is to make such flat elements. I make 2-3 such rectangles at the same time for acceleration. Making such a wall you will understand that they are made easily and very quickly. As a rule, we are interested in the outer side of the castle, the inner part does not represent anything, because it is not visible.

So, a solution of our future walls after a few hours grabbed very much (!) This moment so that it would be pliable, but did not destroy, and if it would be difficult to regenerate. Carefully disassemble the frame and we have a flat rectangle on the table. If you make a wall with teeth, then we make gaps between the teeth gradually removing the solution with a flat tool (I use a metal ruler for this). Further braces are made, windows. Draw everything that prompts you fantasy. To remove the residue of the solution, I use a soft brush (probably saw in the movies as archaeologists work). In the end, you will still lie on the table about the following.

Leave the finished walls about a day on the table. Then they can safely be removed from the table and also put in the corner. When the required number of items have already been made, choose a sunny day for mounting on the country area. This moment is also important. The castle looks more beautiful on some elevation, on a pile of stones. Therefore, prepare the foundation for him. If you use stones, always first put the stones on a small layer of solution. If this is not done, then the stones will move over time and destroy your beauty.
When the foundation is prepared to assemble. First, we install on a cement solution pre-applied to the foundation, for example, Tower No. 1. To the tower on the solution adds the wall number 1. Then set the tower number 2.

The castle is already starting to emerge. Azart covers you. Next, attach the wall number 2 and end with the installation of the tower No. I had a heavy towers, so men needed to believe. Thus, at this stage, it turned out this design (top view)

But the wall number 2 we will have part of the building, so I take a few bricks and form the rectangle of this building. In order for the solution from the inside to do not get into the windows or doors, I closely close them with something flat (I use pieces of flat slate or fragments of flat tiles).
I have an inside of the castle hidden. But if you want it to have a beautiful view - you need to make a wall of № and the inner part for monolith pour with concrete solution or to be concerned with construction trash.

When this design grabs, form a two-tie roof over the building. I have two three bricks (it is thrown out with a solution and a spatula and smoothes under the cone).
This is from the main basic elements, a little by changing them depending on the fantasy (for example, the round towers are tired - do a rectangular formwork and the towers will be square, etc.) you can make a complex lock, such, for example.

The castle made simply from the concrete is not very beautiful. You need to decorate it.

As for imitation. Boulders at the base of the foundation are made very easily as they are arbitrary. Imitation of bricks requires greater patience. A number of horizontal lines scratching the line of horizontal lines and then I make vertical notches with characteristic intervals. Brush with a taste. Where the surface is strongly rough, it can be smoothed with water in a spray and sobrive the soft tassel. When the assembled castle finally dries off, you can cut it a bit. Roof to make a roof tile. I use acrylic paint with the desired color, for painting brick imitation, I purchased such a coller for acrylic - black, red, brown, yellow. Green can be taken to simulate moss. Soft tassel slightly touching masonry with different colors colors to paint the surface. In this case, only the convex surface is painted, and the in-depth part remains gray. The effect is awesome. From half the meter it seems that everything is made of small bricks. In one place of the castle, I even simulated the destroyed brick wall. Himself did not expect such an effect. Already a year, the castle survived the winter and paints as new.

Is it possible to make parts of the house? I work in the garage. But in principle, you can also at home if you do not grow hard. At the same time, the details can be divided into even smaller. Those. For example, make a wall of two parts - the upper where the teeth and the bottom where the gate. Also and tower make two or three cylinders or cubes. Then to transport easier. This allows you to prepare a castle even in the winter-spring time, and in the summer in a couple of days to collect. I am preparing a dry mixture. I fill in half a dry sand add cement and it is very easily mixed with a small children's blade. All this is pouring into a little baady and make the next snack until it fill it. Thus, the dry solution is always in sufficient quantity.

I wish you all success in creativity. And be sure to share your results.

Making a decorative lock with their own hands is a fascinating and laborious process. This construction will be an interesting decoration in your country.

The fabulous kingdom at the garden site will be a good gift and small and adult dreamers.

Before proceeding with the castle, prepare the necessary materials and tools.

Materials:

Foam sheets.
Heaters for pipes.
Crumb of stones or marble.
Set of acrylic paints.
Building glue.
Screws.
Mounting foam with a gun.

Instruments:

Figured screwdriver.
Thin hacksaw.
Set of markers.
Brushes.
Construction spatula.
Insulating tape.
Mass for modeling.

The process of manufacturing a decorative castle for the garden with their own hands

First of all, you must decide on the number of walls and towers of your structure. It is best to use a scheme with 3 walls and 6 towers. After that, you can start making walls. To do this, take two sheet of foam plastic and several plastic pots.

On one of the sheets of foam. Draw sketches of walls. Note that the tower height must correspond to the height of the sheet. The width of the towers must coincide with the width of the roof of the decorative lock. If you want your facility to be in a medieval style, you can make teeth on the tower. Along the edges of the walls, leave a small gap (4-5 cm). It you will have to hide it directly under the turrets.

On the second sheet, draw sketches for towers. Do not forget to cut the windows. Next, with the help of glue, attach the blanks to the walls. As a result of the operations done, you should get a wall with two turrets. The windows can be painted with black acrylic paint. Also, do not forget to paint the arch and the castle gate. If you notice that the side walls of the towers turned out with small protrusions, cut them with a hacksaw. Then wait until the paint dry out the walls and draw the grid.

After that, proceed to painting the walls. It is best to start it from the teeth. First, paint them into one color background with plaster. However, you can paint the teeth using conventional paint from the canister. After that, give your design to dry. Next, cover the entire surface of the wall with decorative plaster. The side walls of the turrets can not be painted, they should be done in the latter order.

The next stage is the manufacture of round towers. In order to make them, it is best to use plastic pipes of small diameter. If you do not have pipes, you can use four pieces of Penolan. From each of the trimming, cut the cylinder with a length of 10-12 cm. You can cut the teeth and glue them to each of the towers, and while the glue dries, secure the seams using the tape.

After the operations done, make longitudinal cuts along the entire length of the workpiece. While the glue will dry, you can paint the windows of the tower of black paint. Then cover the workpiece with the help of plaster.

If the tower configuration is rectangular, you can add stonework elements. To do this, use the mass for modeling. If it is not at hand, use ordinary plasticine. When the towers and walls are completely dried, you can start assembling the decorative lock for the garden with your own hands.

Back to the category

In what sequence to collect a decorative lock

For the manufacture of the lock you will need: 3 cuts of pipes, stones, broken tiles, 1.5 l Dark bottles and cement mortar.

First of all, you need to make a platform to which a decorative lock will be installed. Undoubtedly, it is best to align with a cement mortar. Before assembly, do not forget to pull the walls with the help of a rope and apply the mounting foam to the joints. After that, do the installation of round turrets. To do this, insert the walls in the cuts. Missing parts can be made using a construction foam. Tightly press the ends of the cuts to the walls and fill the tower with mounting foam. From the inside of the fortress, form the missing parts is similar, but do not forget to cut off the extra pieces of foam using the hacksaw.

After assembly, you can do the manufacture of backlight. It should be made of scattered light lamps. They need to be placed inside the fortress.

If this method of manufacturing the castle, you consider too time consuming, you can resort to another. To do this, you need to acquire asbestos-cement pipe and concrete solution. The alternative method has such a sequence:

First of all, insert pipes into the soil and concrete them for good stability. Then all over the perimeter of the lock lay out the stones. After making several rows of masonry let's grab the solution.
Next, cut the plastic bottle into 2 parts. Of these, you can make windows.
After that, proceed to the manufacture of a cone-shaped roof. It can be made from a concrete solution. If you wish, you can lay out a mosaic from above.
Then install the roof on the tower.
If you wish, make the arch. As a support, use the shape of the foam, which, after the concrete solution, should be removed. For better stability, the arch is preferably made grooves.

After the decorative mini lock for the garden is ready, the flag should be made from the old fabric and attach it to the observation tower.

I, just like someone from you there was an idea-fix to make something funny-eye against the background of the country landscape. The choice fell on the mini-lock, since it is most simple to enter at any point of the site, taking into account its geological features. Moreover, it is possible to build creatively by adding or changing its elements on the go.

The castle has a fairly decent volume, therefore it is impossible to build it immediately. To do this, first make individual parts of the castle, then to build it in a couple of days from cubes. The last, the third castle was collected in two days. The neighbors thought that he fell from the sky when they saw him.

So, consider elements of a typical design.

Let's start with the turrets.The cylinder of the desired radius is collapsed from the iron sheet (I have about 2-30 cm). The cylinder is fixed with wire or self-pressing so that it can be easily disassembled in the future. Inside the cylinder is put on anything - bottles, banks - to reduce the consumption of the solution, but the thickness before the ballast should be at least 5 cm.Plive enough thick solution. We give him a few hours for setting to such a state so that when removing the formwork, it did not crumble. The height of the cylindrical formwork can choose themselves. It can be equal to the height of the tower, or less, but then the formwork will have to be disassembled and collecting above the lowest side.

A simple cylinder is boring, here the fantasy flight begins. I make various grooves, wrapped the long strip of the cylinder with a long strip, using this strip as a guide, a screwdriver or chisel, I choose ring recesses. Then, in the lower part, you can simulate a stone masonry, destruction, chips of plaster, cracks - because the castle of ancient.

We proceed to the construction of the walls. Walls we will have either a serf (1) or element of the building (2).

If there is no rubbank, then you can simulate the foundation after a partial setting of a sharp knife or scalpel. Pebbles can also designate future windows. Thus, your task is to make such flat elements. I make 2-3 such rectangles at the same time for acceleration. Making such a wall you will understand that they are made easily and very quickly. As a rule, we are interested in the outer side of the castle, the inner part does not represent anything, because it is not visible.

Leave the finished walls about a day on the table. Then they can safely be removed from the table and also put in the corner. When the required number of items have already been made, choose a sunny day for mounting on the country area. This moment is also important. The castle looks more beautiful on some elevation, on a pile of stones. Therefore, prepare the foundation for it. If you use stones, always first put the stones on a small layer of solution. If this is not done, then the stones will move over time and destroy your beauty.

When the foundation is prepared to assemble. First, we install on a cement solution pre-applied to the foundation, for example, Tower No. 1. To the tower on the solution adds the wall number 1. Then set the tower number 2.

I have an inside of the castle hidden. But if you want it to have a beautiful view - you need to make a wall of № and the inner part for monolith pour with concrete solution or to be concerned with construction trash.

When this design grabs, form a two-tie roof over the building. I have two three bricks (it is thrown out with a solution and a spatula and smoothes under the cone).

This is from the main basic elements, a little by changing them depending on the fantasy (for example, the round towers are tired - do a rectangular formwork and the towers will be square, etc.) you can make a complex lock, such, for example.