Table vertical. Badja for concrete Vertical swivel BP. Types of turntables

- This is part of the equipment of the drilling and milling machine designed to expand the functionality of the equipment. With the help of the rotary table, it is possible without reinstallation to process parts arranged around the circle, rotate the workpiece in various coordinates and perform other operations.

Scope of application and advantages

Rotary tables are widely used on machines of various purposes - both on automatic lines in the serial production of parts and on separate installations. These are milling, vertically drilling machines, forged hammers, presses and other equipment, where it is necessary to ensure the rapid movement of the workpiece processed relative to the working body. Rotary tables and welding operations are used to perform relief and point welding.

The main advantage of the turntable is the possibility of processing parts in different planes. Thus, for milling machines, in addition to moving the workpiece in the three main directions (longitudinal, transverse and vertical), the rotary table can provide the rotation of the part in vertical and horizontal planes. The table ensures the movement of the workpiece in various coordinates, fix it at the required angle of inclination and produce high-precision processing.

The use of the turntable is allowed to significantly reduce the cost of treatment time, increase productivity. When performing welding operations, this type of snap allows you to install the item outside the work zone, thereby not interrupting the production cycle. The functionality of the equipment is significantly increased.

Types of turntables

Rotary tables for metal-cutting machines and other equipment are classified depending on the possible direction of movement. There are five main types of tables:

Rotary tables are available according to standard sizes. Basic diameters: 320, 400, 500 and 630 mm.

Construction of rotary tables

Figure above shows the simplest design of the turntable. In the table of the table (11) the sleeve (10) is pressed. It rotates spindle (2). The spindle has a tablestock table (1). Also in the housing is pressed and sleeve (7). A retainer type (5) retainer (5) is sent to it, which enters the influence of the spring (6) in the sleeve (3).

To control the retainer, handle is provided (4). The turning of the tablet is carried out using the rolling bearing consisting of the closure (12), rings (14) and balls (13). To adjust the axial gap, nut (8) and locking screw (9) are used.

GOST

The general specifications of turning tables with manual and mechanized drive adjusts GOST 16935-93.

Cookie Policy Disclaimer.

This Website Use Cookies to Make Its Service As Much Effective and Userfriendly AS Possible.

What Are Cookies?

Cookies Are Small Pieces of Data Which Allow US to Compare New Visitors with Previous Onees and to Ur Website. We Use The Data Collected Through The Cookies to Offer You An Experience Capable to Reflect Your Interests and Your Preferences and to Allow An Easier Access to Our Services. Cookies Do Not Store Any Personal Information about The User and No Identifiable Data Are Stored. The Use Of Cookies May Be Disabled by Personalizing The Computer Settings: It is Possible to Enable The Clearing of All Cookies Or to Set a Warning Message Every Time Cookies Are Stored. Keep on Surfing The Website If There Is No Need to Change the Cookie Application. Visit AboutCookies.org to Obtain Further Information About Cookies and Their Influence On Your Surfing Experience.

THE TYPE OF COOKIES WE USE

"STRICTLY NECESSARY" COOKIES
These Cookies Are Fundamental in Order to Enable You to Move Around The Website and Use Its Features, such as Entering The WebSite Reserved Areas. Without these Cookies Some Essential Services - SUCH AS FOR COMPILING A FORM FOR A COMPETITIVE EXAM - MAY NOT BE USED.

PERFORMANCE COOKIES
These Cookies Collect Information About How The Use a Website, E.G. Which Are The Most Visited Pages and If Error Messages Are Received From Web Pages. These Cookies Do Not Collect Information That Could Identify A Visitor. All Collected Information Are Aggregated and Therafore Anonymous. These Cookies Are Only Used to Improve The Operation of A WebSite. Using Our WebSite, The User Accepts The Installation Of Such Cookies on Her / His Device.

"Functionality" Cookies
Cookies Allow The Website to Remember The Choices Made by The User (Such As Name, Language Or Origin) And They Supply Modern and Personalized Functions. These Cookies May Also Be Used to Remember The Changes Made to the Text or font size and to other Sections of Web Pages Which May Be Personalized. They Be used to Supply You The Required Services, Such As Watching a Video Or the Comments on a blog. These Cookies May Be Made Anonymous and Incapable to Control Your Surfing Activity On Oter Websites. Using Our WebSite, The User Accepts The Installation Of Such Cookies on Her / His Device.

Here Following Is The Table Containing The Cookies Used in Our Website.

Dominio.	Nome.	Durata.	Azienda.	Tipologia.
www.linvisibile.com.	Phpsessid	Session.	Linvisibile	TECNICO DI SESSIONE
linvisibile.com.	_GA	2 Anni.	Google	Analytics.
linvisibile.com.	_Gat.	24 ORE.	Google	Analytics.
.DoubleClick.net.	id	2 Anni.	Google	Advertising

How to MANAGE COOKIES ON YOUR COMPUTER

If You Want to Allow Cookies on Our Website, Please Follow The Steps Beelow:

Google Chrome.

1. Click on "Under the Hood", Find the "privacy" section and select the "Content Settings" Button. 3. NOW SELECT "ALLOW LOCAL DATA TO BE SET"

Microsoft Internet Explorer 6.0, 7.0, 8.0, 9.0

1. Click on "Tools" in the Upper Part of the Browser Window and Select "Internet Options"; Now Click on the "privacy" tab.
2. While Allowing Cookies on Your Browser, Make Sure That The Privacy Level Is Set to Medium or Lower.
3. The Use Of Cookies Is Not Allowed If The Privacy Level Is Over Medium.

Mozilla Firefox.

1. Click on "Tools" in the Upper Part of the Browser Window and Select "Options"
2. SELECT THE PRIVACY ICON
3. Click On Cookie and Select "I ALLOW THE WeBSITES TO USE COOKIES"

Safari On Osx

1. Click On 'Safari' In The Upper Part of the Browser Window and Select The Option "Preferences"
2. Click On 'Safety' and On "Accept Cookies"
3. SELECT "ONLY FROM THE WeBSITE"

Mozilla and Netscape on OSX

1. Click on 'Mozilla' Or 'Netscape' In The Upper Part of the Browser Window and Select The Option "Preferences".
2. Scroll Down Till Displaying The Cookies In "Privacy and Safety".
3. SELECT "ALLOW COOKIES ONLY FOR THE SOURCE WeBSITE"

1. Click on "Menu" in the upper part of the browser window and select "settings"
2. SELECT "PREFERENCES" AND THEN THE ICON "ADVANCED".
3. SELECT THE OPTION "ALLOW COOKIES"

Google Analytics.

This WebSite Uses Google Analytics, a Web Analytics Service Provided by Google, Inc. ("Google"). Google Analytics Uses "Cookies", Which Are Text Files Placed On Your Computer to Help The WebSite Analyse How Visitors Use the Site. The Information Generated by The Cookie About Your Anonymous IP Address) Will Be Transmitted to and Stored by Google On Servers in the United States. Google Will Use This Information for the Purpose of Evaluating Your Use of the Website, Compiling Reports on WebSite Activity for WebSite Operators and Providing Other Services Relating to Website Activity and Internet Usage. Google May Also Transfer This Information to Third Parties Where Required to Do So by Law, Or Where Such Third Parties Process The Information on Google's Behalf. Google Will Not Associate Your IP Address WITH ANY OTHER DATA HELD by Google. You may Refuse The Use Of Cookies by Selecting The Appropriate Settings on Your Browser, However Please Note That If You Do This You May Not Be Able to Use the Full Functionality of this Website. By using this Website, You Consent to the Processing of Data About You by Google In The Manner and for the Purposes Set Out Above.

YOU MAY ALSO REFUSE THE COLLECTION OF DATA GENERATED by The Cookie and Related To Your Use of The Website (Including Your IP Address) As Well As The Processing of The Data by Google by Downloading and Installing the Brown Plugin Available by Clicking on the Link Below

Characteristics:

Model	Price, rub	Volume (l)	G / n (kg)	Dimensions (mm)
BP-1.0	50050,00	1 000	2 500	3100x1560x900.
BP-1,6	58702,00	1 600	4 000	3700x1560x900.
BP-2,0	66066,00	2 000	5 000	3700x1850x1100.

Badja for concrete Vertical swivel BP:

Badja for concrete Vertical swivel BP is used to supply concrete with a boom or tower crane for a large height. It is also used to supply concrete directly from the mixer.
The main features of the Bathos are the low cost of work, versatility and simplicity to use.

The main difference from the vertical bade is that the swivel bady has two positions.

When booting, when the Badja is horizontally, the process of conchor overload from the mixer in Badew is significantly simplified ( badja concrete shoes).

At the same time, there is no need to organize a veil or an overpack for the baffle supply to the mixer, unlike the usual vertical baud.

When serving concrete, badja concrete swivel Takes a vertical position, which allows you to significantly simplify transportation by reducing dimensions in width. Badja moves with a boom or tower crane, which allows you to significantly die on the rental of a concrete pump or a concrete-feeding boom.

Badja swivel for the supply of concrete is the optimal solution for construction objects, on which it is advisable to apply not expensive equipment for the supply of concrete, which operates personnel who does not have special skills and tolerances.

Badja concrete Vertical swivel bp Filled with mixer concrete, manually or from mobile concrete water. After filling the tank of the baud, with the help of a boom or tower crane, the Badya is fed to the overlap, to the place of operation. A convenient mechanism allows you to accurately dose the submission of concrete, not allowing to occur overrun and loss of concrete during work.

Badja concrete Vertical swivel bp Allows monolithic work with personnel who does not have special training. There is enough introductory briefing to start work, unlike the use of high-tech and expensive means of mechanization, such as concrete pump.

When using Betheos for concrete, concrete consumption for losses during transportation is significantly reduced. Badja concrete Vertical swivel bpit does not require much care after the work, it is enough to rinse the equipment with water.

We draw your attention to the fact that this website is only informative and under any information and prices posted on the site are not a public offer determined by the provisions of Articles 435 and 437 of the Civil Code of the Russian Federation.

Cost, availability of goods and information about possible discounts check with our managers through a phone call to the numbers or E-mail addresses specified in the contact information.

Production time up to 14 days.

Swivel mobile, magnetic marker board on a metal frame, painted by powder using aluminum color. There is the ability to change the slope of the chalkboard.

The surface is intended for writing information using a specialized marker for marker boards.

Due to the magnetic surface, the information can be attached to the floorboard using magnets.

A marker coating of the rotary board allows you to write markers for marker boards, and when erasing does not remain traces. On the surface you can withdraw the image from the projector.

Today, one of the necessary and modern attributes of the office or educational institution are mobile turning boards of our production. This is a wonderful and multifunctional visualization tool that has managed to prove himself:

The popularity of Mobile Rotary Boards, made on patented Boardsys technologies, is simply explained - this product is distinguished by mobility and is made of 100% environmentally safe materials. The board has a presentable appearance and ease of operation. Due to the rotation function, the useful area of \u200b\u200bthe floor board is doubled. Surface of the mobile turning board - magnetic markerWhat allows you to use dry erasing markers (green, red, blue, black) or magnets for writing. The transition from one surface to another is carried out simply by turning the board.

It is not surprising that it is often that Boardsys's mobile turning board is a relevant subject that can help in the following directions:

• allows you to perform a visual part of your report in advance and have another free work surface in stock;
• helps to organize and optimize work in the office or in the classroom;
• visually submit information;
• attract attention to important messages.

Mobile BoardSys Swivel Boards are equipped with a comfortable tray (along the entire length of the board) for markers and chalk, as well as a fixing kit.

All products are verified for compliance with European environmental safety standards.

We offer our goods packaging service for greater safety when transporting through a transport company.

• Completed with a tray (along the entire length of the board), as well as fitting for mounting to the wall and installation scheme
• Steel sheet coating - production: South Korea.
• Metal and aluminum profile.

Tables turning horizontal TS (160-1250 mm).

	TS. 160A.	TS. 200A.	TS. 250A.	TS. 320A.	TS. 400A.	TS. 500A.	TS. 630A.	TS. 800A.	TS. 1000A.	TS. 1250A.
Basic diameter, mm	Ø160	Ø200	Ø250	Ø320	Ø400.	Ø500	Ø630	Ø800	Ø1000	Ø1250
	KM2.	KM3.		KM4.		KM5		KM6.		-
Hole diameter, mm	Ø25x6	Ø30x6		Ø40x10		Ø50x12.		Ø75x14.
T-groove width, mm	10	12		14		18		22
T-groove angles	90 °		60 °			45 °
Width groove fastening, mm	12	14		18		—	—	—	—	-
	1.5	1.75	2	2.5	3.5		4.5	5.5		5
	1:90					1:120				1:180
Graduation	360 °
Turning table at one turn worm	4 ° (1 "division)					3 ° (1 "division)				2 °
Minimum scale value	10 "
Accuracy of indications	80"	60"						30"
	100	150	200	250	300	550	700	1250	2000	3000
Weight, kg	16.5	22.5	33.5	65	125	215	345	800	1300	1900
Price, rub.	17 100	19 100	21 200	32 400	49 100	105 700	234 300	592 300	938 500	1572 000

Dimensions of rotary horizontal TS tables:

	TS160A.	TS200A.	TS250A.	TS320A.	TS400A.	TS500A.	TS630A.	TS800A.	TS1000A.	TS1250A.
A.	260	290	330	410	530	640	820	1000	1170	1400
B.	196	236	286	360	450	560	700	890	1080	1300
C.	332	369	422	493	612	753	898	1080	1295	1420
D.	Ø160	Ø200	Ø250	Ø320	Ø400.	Ø500	Ø630	Ø800	Ø1000	Ø1250
G.	12	14		18		22		22	-	22
H.	75	80	90	110	140	158.5	160	215	250	283
J.	12	14		18		22		30	-	30
K.	76	91.25	102.5	128.5	180	230	295	364	364	487.5
L.	194	211	241	273	337	393	468	535	654	690
M.	KM2.	KM3.		KM4.		KM5		KM6.		-
P.	27	27	30.5	44	60	65	68	76	106	116
Q.	125				160	180	220	250
d.	Ø25	Ø30		Ø40		Ø50		Ø75
h.	6			10		12		14

Tables swivel and accessories to them (production Russia).

	5030			5053
	5030
	5040			5055
	5045			5057
	5050			5059
	6130
	5120

Tables turning horizontal TS (1600-2500 mm).

Technical characteristics of turning tables of rotary horizontal TS:

	TS1600A.	TS2000A.	TS2500A.
Basic diameter, mm	1600	2000	2500
Through hole diameter, mm	100	120	-
Diameter and depth of the hole for centering, mm	120x25	150x30	-
T-groove width, mm	22
Corners of T-grooves, hail.	22,5
Worm and worm gear modules	8
Worm transfer coefficient	1:120	1:180
Graduation of the entire table, hail.	360
Turning the table at one turn is worm, hail.	3	2
Minimum scale value, min.	10
Accuracy of readings, min.	30
Maximum weight of the workpiece, kg	5500	8500	10000
Prices for turning tables TS (1600-2500), rub.	2 777 000	4 090 000	4 123 000

Tables rotary horizontal vertical TSL (100 - 800 mm).

TSL.

1. Type 5057. WZK Grandma back.

Technical characteristics of turning horizontal vertical TSL tables:

	TSL100.	TSL160.	TSL200.	TSL250	TSL320.	TSL400.	TSL800.
Basic diameter, mm	Ø100	Ø160	Ø200	Ø250	Ø320	Ø400.	Ø800
The taper of the centering hole	KM2.		KM3.		KM4.		KM6.
Hole diameter, mm	Ø20x8	Ø25x6.	Ø30x6		Ø40x10		Ø75x14.
	70	125	150	170	210	260	500
T-groove width, mm	6	10	12		14		22
T-groove angles	90 °			60 °			45 °
Width groove fastening, mm	10	12	14		18		22
Cherry gear modules	1	1.5	1.75	2	2.5	3.5	5.5
Worm transfer coefficient	1:72	1:90					1:120
Graduation	360 °
Scale Makhovichka	2"	1"
Minimum scale value	10"
Accuracy of indications	120"	80"	60"
	20	100	150	200	250	300	1500
	10	50	75	100	125	150	750
Weight, kg	7	23	31.5	46	77	150	1150
Price on turning TSL Tables, rub.	19 100	22 000	23 700	27 000	42 500	62 500	710 000

Tables turning horizontal vertical T13 500b, Ø500 mm.

Tables swivel horizontal vertical series T13 Designed for division, circular cutting, installation of angles, boring, local processing and similar work together with milling machines. This type of tables is specifically designed to perform machine operations with large measurement capabilities than TS series tables. The base allows you to use tables and in a vertical position to carry out work using the backstone.

Additionally (not included) The table can be recycled:

1. Type 5055. FL flange for fastening a spiral cartridge.
2. Type 5054. DK11 Spiral Cartridge.
3. Type 5053. DP Dividing disk that allows the operator to precisely divide the circle when rotating 360 °, in any proportions and on any angles.

Technical characteristics of the tables of rotary horizontal vertical T13500B:

	T13500B.
Basic diameter, mm	Ø500
The taper of the centering hole	KM4.
Hole diameter, mm	Ø50x15
Center height with vertical position, mm	286
T-groove width, mm	20
T-groove angles	45 °
Cherry gear modules	3.5
Worm transfer coefficient	1:90
Graduation	360 °
Turning table for one revolution worm	4 °
Minimum scale value	10"
Accuracy of indications	60"
Max. Load on the bearing in a horizontal position, kg	550
Max. Bearing load in vertical position, kg	275
Net weight / gross, kg	225 / 260
Packing size, mm	955x690x337
Price on T13500B table, rub.	130 200

Dimensions of rotary horizontal vertical T1350B:

Turning tables tilted TSK (160 - 400 mm).

Tables turning tilted series TSK. Designed for division, circular cutting, installation of angles, boring, local processing and similar work together with milling machines. This type of tables is specifically designed to perform machine operations with large measurement capabilities than TS or TSL series tables. The base allows you to use tables and in a vertical position to carry out work using the backstone.

Additionally (not included) The table can be recycled:

1. Type 5055. FL flange for fastening a spiral cartridge.
2. Type 5054. K11 Spiral Cartridge.
3. Type 5053. DP Dimensional device that allows the operator to accurately split the disk when rotating 360 °, in any proportions and on any angles.

Technical characteristics of TSK tilting tables:

	TSK160.	TSK200.	TSK250	TSK320.	TSK400.
Basic diameter, mm	Ø 160.	Ø 200.	Ø 250.	Ø 320.	Ø 400.
The taper of the centering hole	Km2.	KM3.		KM4.
Hole diameter, mm	Ø 25x6	Ø 30x6		Ø 40x10
T-groove width, mm	10	12		14
Cherry gear modules	1.5	1.75	2	2.5	3.5
Width groove fastening, mm	12	14		18
T-groove angles	90 °		60 °
Worm transfer coefficient	1:90
Graduation	360 °
Tilt angle	0 - 90 °
Scale Makhovichka	1"
Minimum scale value	10"
Accuracy of indications	2"
Max. Load on the bearing in a horizontal position, kg	100	150	200	250	300
Max. Bearing load in vertical position, kg	50	75	100	125	150
Weight, kg	36	57	80	135	280
Price on the table turning TSK, rub.	52 000	56 400	65 100	88 300	131 000

DPE discs DP for TS, TSL, TSK tables.

Drive Applicability:

	Applicability	Disks
			5 100
	TS160A, TS200A, TS250A, TS320A TSL160, TSL200, TSL250, TSL320 TSK250, TSK320.		6 600
	TS400A. TSL400. TSK400.	A: 34, 37, 38, 39, 41, 43, 44, 50, 52, 56, 61 B: 46, 47, 49, 51, 53, 54, 57, 58, 59, 62, 64	9 800
	TS500A, TS630A, TS800A, TS1000A T13500B.	A: 33, 34, 37, 38, 39, 41, 43, 44, 50, 52, 56, 61 B: 46, 47, 49, 51, 53, 54, 57, 58, 59, 62, 63, 64	14 800

Cartridges Turning PS3 for fixing on turning tables.

The cartridges are equipped with straight and reverse rotable cams, key and fastening bolts.
To install on tables, transition flanges are required Type 5055 FL.

Designation

D, mM.

D1, mM.

D2, mM.

D3, mM.

H, mM.

H1 mM.

h., mM.

Max. Diam. crane straight / arr., mm

Mmax. admit revolutions rpm.

Weight, kg

DK11-80(PS3-80)

6 900

DK11-100 (PS3-100)

DK11-125(PS3-125)

7 560

DK11-160.(PS3-160)

11 400

DK11-200(PS3-200)

17 800

DK11-250(PS3-250)

21 200

DK11-315(PS3-315)

40 600

DK11-400 (PS3-400)

58 200

Flanges for attaching turning cartridges FL on turning tables TS, TSL, TSK.

The correspondence of the diameter of the cartridges of turning flanges:

Flange
Basic diameter, mm
Cartridges DK or PS.	DK11-80 PS3-80	DK11-125 PS3-125	DK11-160 PS3-160	DK11-200 PS3-200	DK11-250 PS3-250	DK11-315 PS3-315	DK11-400 PS3-400
Cartridge diameter, mm
	1 900	3 100	3 400	5 100	9 100	10 200	12 100

Grandma rear adjustable wzk.

Grandmas rear adjustable WZK. Designed for use with vertical rotary tables. They are used to hold and center cylindrical and other parts when processing on machines. The center is the height of the center and the angle of inclination can be changed and configured as needed. The design allows you to draw the center inside to perform the pressure and repetition of the operation. For safety, the center is fixed by a clamping handle.

TECHNICAL SPECIFICATIONS OF THE REAR BOLODS WZK:

Applicability
MIN base height To the center of Max
Cone center
Width groove fastening, mm
The angle of tilt center, hail.
Moving the center, mm
Gabarites, mm.
				6 500	6 900	7 600

Designation

Grandma rear unregulated wz and tsl400.

Grandmas rear Wz and TSL400-2 Designed for use with vertical rotary tables. They are used to hold and center cylindrical and other parts when processing on machines. The design allows you to draw the center inside to perform the pressure and repetition of the operation. For safety, the center is fixed by a clamping handle.

Technical characteristics of the backs of the wz:

Table longitudinal transverse MG-2A with a turning ground.

Table longitudinal and transverse with a turning ground Mg-2a. - This is a multifunctional affiliation for widespread use, mainly on milling, drilling and other machines. The use of longitudinal and transverse movement together with a turn around the base makes it easier and speeding up the processing of parts.

l.

Technical characteristics of the table with a turning base MG 2a:

	Mg-2a.
Table size, mm
The magnitude of the longitudinal movement of the table, mm
The magnitude of the transverse movement of the table, mm
Width T-shaped groove, mm
Distance between T-shaped groove, mm
Minimally read the magnitude of the limb
The maximum allowable weight of the workpiece relative to the center of the table, kg
The maximum allowable effort relative to the center of the table, n
Deviation of the surface along the length of the table, mm
Permissible deviation of perpendicularity, mm
Parallelism of the surface of the table to the surface of the base, mm
Permissible deviation when turning the table 0-360 °, mm
Net weight, kg
Gross weight, kg
Packaging dimensions, mm
	40 100

Tables swivel horizontal vertical TK13EL, CNC.

Tables horizontally vertical with through passage hole in the spindle series TK13EL CNC is a great solution for applying them on milling CNC machines and processing centers. They are used in combination with a CNC controller of the machine or with an independent controller on machines without CNC. To ensure work with widespread use is a tablebuck with a through passage hole, as well as other devices allowing to fix the part between the table and the back of the grandmother. With their help, the operation can be performed especially accurately. The presence of a through passage in the spindle allows the use of hydraulic (pneumatic) mechanized cols and amateur in the processing of long shafts and other products.

TK13EL table specifications, CNC:

	TK13200EL	TK13250EL	TK13315EL
Basic diameter, mm
Height centers, mm
Diameter of the passing hole, mm
Width of the fixing groove-knap, mm
Width fixing t grooves, mm
Curving Curving Care
Gear ratio reducer
Maximum speed of rotation, rpm
Turn angle for one impulse
Servo drive power, kW
Servo torque, nm
Accuracy of division
Positioning stability
Clamping force at a pressure of oil 15x10 5 Pa, nm
Effort for; im at air pressure 5x10 5 pa, nm
Max. The weight of the workpiece in a horizontal position, kg
Max. The weight of the workpiece in the vertical position, kg
Maximum torque, nm
Net weight, kg

The main sizes of the turning table TK13200L, TK13250L, TK13315K:

TK13200EL

TK13250EL

TK13315EL

TK13200EL
TK13250EL
TK13315EL