GOST 5336 80 Designation. Steel Wicker Single Mesh

Wicker steel grids
Single

Technical conditions

GOST 5336-80

Publishing standards

State Standard of the SSR Union

Date of administration 01.01.82

This standard applies to steel wicker single meshs with rhombic and square cells made by plexus in one pressing of flat spirals from steel wire and used for fences, heat-insulating works, mounting mining machines in mines and mines, sieving materials.

1. Basic parameters and sizes

1.1. The grid is divided into the form of cells:

rhombic - P (the sharp corner of the rhombus should be 60 °) -;

by type of surface:

without cover,

from wire galvanized - 0.

Grids according to the accuracy of the cell size are divided into groups 1 and 2.

(Modified edition, change No. 1, 2).

1.2. The size of the side of the cell in the light and the diameter of the wire must match the specified in Table. one.

Table 1

Cell number	Nominal side of the side of the cell in the light, mm	Nominal wire diameter, mm
With a rhombic cell



With a rhombic or square cell




With a square cell

It is allowed in coordinating the consumer with the manufacturer Making grids of lightweight (OB) No. 20, 25, 35 of low carbon thermally untreated wires without coating with a nominal diameter of 1.8 mm instead of 2.0 mm; Mesh No. 45 of wire with a diameter of 2.0 mm instead of 2.5 mm; No. 50 from the wire with a diameter of 2.5 mm; No. 80 of the wire with a diameter of 3.0 mm No. 100 of wire with a diameter of 4.0 mm.

Examples of conventional designations

Mesh with a rhombic cell number 12, from thermally untreated wire, with a diameter of 1.6 mm, groups 1:

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with a square cell number 20, from galvanized wire, with a diameter of 2.0 mm, groups 2:

Grid 2-20-2.0-0 GOST 5336-80

Mesh with a square cell No. 20 of the wire with a diameter of 1.8 mm:

Grid 20-р GOST 5336-80

1.3. The limit deviation for the average arithmetic size of the sides of the cell should not exceed + 6% for the grids of the 1st group and + 10% for the grids of the 2nd group.

1.4. The limit deviation of the corner of the cell from the nominal should not exceed ± 10 °.

1.5. The width of the grid and the limit deviations must correspond to the specified in Table. 2.

Grid No. 15 of the wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

Grid number	Width, mm.	Limit deviations, mm
Grid number	Width, mm.	1st group	2nd groups


	1000, 1500, 2000	1.12 cells
			1.6 cells
	2000, 2500, 3000

(Modified edition, change No. 1).

2. Technical requirements

2.1. Grids should be manufactured in accordance with the requirements of this standard for the technological regulations, approved in the prescribed manner, from low carbon thermally untreated without coating or galvanized wire of normal production accuracy by TU 14-4-1563-89.

Grids of the 1st group should be made of wire with minus limit deviations equal to the sum of absolute values \u200b\u200bof limit deviations.

(Modified edition, change No. 1, 3).

2.2. Each helix should consist of one wire.

2.3. Related spirals should be woven into each other with all the turns without skipping.

2.4. The grid should not be inverted spirals.

(Modified edition, change No. 2).

2.5. The ends of the spirals on both sides of the grid must be cut and each end at the junction site should be bent to its helix.

2.6. Grids after manufacture are coagulated in rolls. The roll should consist of one piece of mesh at least 5 m long for grids No. 5-60 and at least 3 m for grids No. 80, 100.

It is allowed to roll rolls from two pieces of crosslinked spiral.

For grids of the 1st group, a roll should consist of one piece of at least 10 m long for grids No. 5-60 and at least 5 m for grids No. 80, 100.

(Modified edition, change No. 1, 2).

2.7. Roll mass should not exceed 80 kg. For grids No. 80 and 100, an increase in the mass of the mesh roll to 250 kg is allowed.

(Modified edition, change No. 1).

3. Rules of acceptance

3.1. Grids are taken by parties. The party should consist of grids of one number, one width, one material and is decorated with one quality document. The document on quality must contain:

trademark or name and trademark of the manufacturer;

conditional grid designation;

width in millimeters and mesh length in meters, total net in square meters;

the number of rolls in the party.

(Modified edition, change No. 1).

3.2. To check the quality of weave, the bends of the ends of the spiral, the average arithmetic value of the size of the cell side in the light, the length, the width of the mesh and the corner of the cell from the batch select 5% rolls, but not less than two.

(Modified edition, change No. 2).

3.3. Upon receipt of unsatisfactory test results, at least one of the indicators on it is re-conducted on a double number of rolls.

Results of re-checks are distributed to the entire batch.

(Modified edition, change No. 1).

4. Test methods

4.1. The quality of weave and the bending of the ends of the spirals is determined visually when the grid rolls are rewound.

4.2. The average arithmetic value of the size of the cell side in the light is determined in three places of the grid, which is not less than 100 mm from the edge, are counted in two directions in parallel to the sides of the cell of 10 cells for grids No. 5-15 and 5 cells for grids No. 20 -100 and measure the length of the site, including one extreme wire, on which the countdown cells are located. The length of the area to determine the average arithmetic value of the sample side of the cell in the light is measured by a meter or a ruler with a division of 1 mm.

The average arithmetic value of the size of the cell side in the light ( but), mm, calculated by the formula

where l. - the length of the site, on which there are consistently counted in the corresponding directions 5 or 10 cells, mm;

n. - the number of check-in cells;

d. - Nominal wire diameter, mm.

The final value of the average arithmetic size of the sides of the cell in the light is defined as the arithmetic average of six measurements.

4.3. The diameter of the wire is measured by the micrometer according to GOST 6507-90 before manufacturing the mesh.

(Modified edition, change No. 2).

4.4. The width of the mesh is measured according to the protruding curved ends with a meter or roulette with a division of 1 mm. The mesh length is measured in a stretched state, eliminating the change in the shape of the cells, a meter or tape measure with the price of dividing 1 mm or counter.

4.5. The cell angle is checked by a tilt of GOST 5378-88 or a template in three places of the grid, but not closer than 2 cells from the edge of the mesh.

5. Packaging, Marking, Transportation and Storage

The packaging of the grid transported to the areas of the Far North and hard to reach areas must correspond to GOST 15846-79.

(Modified edition, change No. 1, 2).

5.3. At the request of the consumer, the grid is covered by conservative Lubrication of the HCR on the approved technical documentation or a mixture of HCB and industrial oil according to GOST 20799-88 in a ratio of 1: 1.

5.4. To the end of the roll or package must be attached a shortcut that indicates:

trademark or name and trademark of the manufacturer;

name and trademark of the manufacturer;

conditional grid designation;

the width is in millimeters and the length of the grid in meters, the total amount of the grid in square meters.

5.3 - 5.4. (Modified edition, change No. 1).

5.4A. Transport markings - according to GOST 14192 -77.

(Introduced additionally, meas. No. 1).

5.5. The grid is transported by packages according to GOST 26663-76 or rolls. Packages are allowed without the use of pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall package sizes: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. The enlarged cargo place is formed when transporting the consumer of two or more rolls.

Packing tools are:

kathan diameter 6.5 mm according to GOST 14085-79;

wire and tape on other regulatory and technical documentation.

Package mass no more than 1 tons.

The grids are transported by the transport of all types in accordance with the rules for the transport of goods acting on the transport of this species and the technical conditions of loading and fastening of goods approved by the Ministry of Ways of the USSR. Transportation by rail is carried out by writing or small shipments. On an open rolling stock, the grid is transported only by packages.

The conditions for transporting the grid in terms of the effects of climatic factors must comply with the conditions of storage 5 and 8 according to GOST 15150-69.

(Modified edition, change. No. 1, 2, 3).

5.6. The storage of grids must comply with the conditions 5 according to GOST 15150-69.

(Modified edition, change No. 1).

ATTACHMENT

Reference

Table of living section and theoretical mass of 1 m2 mesh

Grid number	Wire diameter, MM.	Live mesh cross section %	Mass of 1 m2 mesh, kg
Rhombic Cell Mesh



Grid with a rhombic or square cell
		75,3 (78,9) 71,5 (76,2)	2,20 (1,96) 3,00 (2,68)
		76,3 (79,0) 73,3 (77,0)	2,48 (2,24) 3,24 (2,92)
		77,5 (80,9) 76,0 (78,9)	2,57 (2,27) 3,25 (2,88)

Square Cell Mesh

Note. The values \u200b\u200bindicated in brackets are distributed on mesh with a square cell.

(Modified edition, change No. 2, 3).

Information details

1. Designed and introduced by the Ministry of Metallurgia of the USSR

Developers

K.G. Zalyalutdinov, N.A. Galkina, V.D. Egorov, L.A. Parnisha, G.L. Sedun

2. APPROVED AND INTRODUCED RESOLUTION OF THE STATE COMMITTEE OF THE USSR on standards from 31.03.80 No. 1466

3. Instead of GOST 5336-67

4. Reference regulatory and technical documents

TU 14-15-213-89

TU 14-4-1563-89

5. Restriction of the validity period of the action of the USSR State Standard from 08.04.91 No. 457

6. Reprint (December 1992) with amendments No. 1, 2, 3, approved in September 1986, April 1991 (IUS 12-86, 6-89, 7-91)

OST 14.15.193-86

OST 14-4-210-87

TU 14-4-1563-89

5. Restriction of the validity period of the action of the USSR State Standard from 08.04.91 N 457

6. Edition with changes No. 1, 2, 3, approved in September 1986, March 1989, April 1991 (IUS 12-86, 6-89, 7-91)

This standard applies to steel wicker single meshs with rhombic and square cells made by plexus in one pressing of flat spirals made of steel wire and used for fences, thermal insulation works, mounting mining machines in mines and mines, sieving materials.

1. Basic parameters and sizes

1.1. Grids subdivide:

- in the form of cells on:

rhombic - P (sharp corner of rhombus should be 60 °) - Damn.

square - Damn 2;

- By type of surface:

without cover;

from wire galvanized - 0.

Grids according to the accuracy of the cell size are divided into groups 1 and 2.

(Modified edition, change. N 1, 2).

1.2. The size of the side of the cell in the light and the diameter of the wire must match the specified in Table 1.

Table 1


Cell shape	Grid number	Nominal side of the side of the cell in the light, mm	Nominal wire diameter, mm
Rhombic


Rhombic or square



Square

It is allowed to coordinate the consumer with the manufacturer, the manufacture of meshes of lightweight (circuit) Nn 20, 25, 35 of low carbon thermally untreated wire coating with a nominal diameter of 1.8 mm instead of 2.0 mm; Mesh N 45 from wire with a diameter of 2.0 mm instead of 2.5 mm; N 50 from wire with a diameter of 2.5 mm; N 80 Wire with a diameter of 3.0 mm and N 100 of wire with a diameter of 4.0 mm.

Examples of conventional designations

Mesh with a rhombic cell N 12, made of thermally untreated wire with a diameter of 1.6 mm, groups 1:

Mesh 1-R-12-1.6GOST 5336-80

Mesh with a square cell N 20, from galvanized wire with a diameter of 2.0 mm, groups 2:

& nbsp.Grid 2-20-2.0-0.GOST 5336-80

Grid with square cell N 20, lightweight, from wire with a diameter of 1.8 mm:

& nbsp.Grid 20-OGOST 5336-80

1.3. The limit deviation for the average arithmetic size of the cell side should not exceed + 6% for group meshes 1 and + 10% for group 2 grids.

1.4. The limit deviation of the corner of the cell from the nominal should not exceed ± 10 °.

1.5. The width of the grid and the limit deviations must correspond to the specified in Table 2.

Grid N 15 from wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2


Grid number	Width, mm.	Limit deviations, mm
			group 2.

		1.12 cells
	1000, 1500, 2000
			1.6 cells
	2000, 2500, 3000

(Modified edition, meas. N 1).

2. Technical requirements

2.1. Mesh should be made in accordance with the requirements of this standard for the technological regulations, approved in the prescribed manner, from low carbon thermally unprocessed without coating or galvanized wire of normal manufacturing accuracy by TU 14-4-1563.

Mesh Group 1 should be made of wire with minus limit deviations equal to the sum of absolute values \u200b\u200bof limit deviations.

(Modified edition, meas. N 1, 3).

2.2. Each helix should consist of one wire.

2.3. Related spirals should be woven into each other with all the turns without skipping.

2.4. The grid should not be inverted spirals.

(Modified edition, meas. N 2).

2.5. The ends of the spirals on both sides of the grid must be cut and each end at the junction site should be bent to its helix.

2.6. Grids after manufacture are coagulated in rolls. The roll should consist of one piece of mesh with a length of at least 5 m for grids Nn 5-60 and at least 3 m for grids NN 80, 100.

It is allowed to roll rolls from two pieces that are crosslinked by a spiral.

For groups of group 1, the roll should consist of one piece of at least 10 m long for grids Nn 5-60 and at least 5 m for grids NN 80, 100.

(Modified edition, change. N 1, 2).

2.7. Roll mass should not exceed 80 kg. For grids NN 80 and 100, an increase in the mass of the mesh roll to 250 kg is allowed.

(Modified edition, meas. N 1).

3. Rules of acceptance

3.1. Grids are accepted by parties. The party should consist of grids of one number, one width, one material and is decorated with one quality document. The document on quality must contain:

- Conditional designation of the grid;

- width in millimeters and the length of the grid in meters, the total amount of the grid in square meters;

- The number of rolls in the party.

(Modified edition, meas. N 1).

3.3. Upon receipt of unsatisfactory test results, at least one of the indicators, it is re-conducted on a double amount of rolls.

Results of re-checks are distributed to the entire batch.

(Modified edition, meas. N 1).

4. Test methods

4.1. The quality of weave and the bending of the ends of the spirals is determined visually when the grid rolls are rewound.

4.2. The average arithmetic value of the sample side of the cell in the light is determined in three places of the grid, which are not less than 100 mm, are counted in two directions parallel to the sides of the cell of 10 cells for grids NN 5-15 and five cells for grids NN 20-100 And the length of the site is measured, including one extreme wire, on which the subject cells are located. The length of the area to determine the average arithmetic value of the sample side of the cell in the light is measured by a meter or a ruler with a division of 1 mm.

The average arithmetic value of the size of the cell side in light (), mm, calculated by the formula

where - the length of the site, on which five or 10 cells consistently counted in the corresponding directions are located in the corresponding directions;

- the number of check-in cells;

- Nominal wire diameter, mm.

The final value of the average arithmetic size of the sides of the cell in the light is defined as the arithmetic average of six dimensions.

4.3. The wire diameter is measured by the micrometer according to GOST 6507 before making the grid.

(Modified edition, meas. N 2).

4.5. The angle of the cell is checked by a tilter according to GOST 5378 or a template in three places of the grid, but not closer than two cells from the edge of the mesh.

5. Packaging, Marking, Transportation and Storage

5.1. Each mesh roll must be tied by low carbon wire with a diameter of 1.2-2.5 mm according to GOST 3282 or TU 14-4-1563 or the waste of this wire in the middle and at the edges, or the end of the mesh web should be suspended the same wire to roll in the middle and At the edges.

(Modified edition, meas. N 1, 3).

5.2. The ends of the roll should be wrapped with paper according to GOST 8828 or other paper made according to regulatory and technical documentation (NTD), or a packaging cloth according to GOST 5530, or a tare cannon, or a glued web, or cross-wing flap from the textile industry, as well as other Materials made on NTD, excluding the use of cotton and linen fabrics and not worsening the quality of the packaging.

The NN 5-50 mesh is allowed inclusively not packaging, but be sure to tie the cross-shakers of the wire roll in accordance with paragraph 5.1 or in another way, subject to preventing the clutch of the cooled wires with each other.

Packaging materials on the ends of rolls are tied with wire in accordance with paragraph 5.1.

The packaging of the grid, transported to the areas of the Far North and hard to reach areas, must correspond to GOST 15846.

(Modified edition, change. N 1, 2).

5.3. At the request of the consumer, the grid is covered with conservation lubrication of the HCRs according to the established manner or a mixture of HCB and industrial oil according to GOST 20799 in a 1: 1 ratio.

5.4. To the end of the roll or package must be attached a shortcut that indicates:

- trademark or name and trademark of the manufacturer;

- Name and trademark of the manufacturer;

- Conditional designation of the grid;

- Width in millimeters and mesh length in meters, the total amount of mesh in square meters.

5.3-5.4. (Modified edition, meas. N 1).

5.4A. Transport markings - according to GOST 14192.

(Introduced additionally, meas. N 1).

5.5. Grids are transported by packages according to GOST 26663 or rolls. Packages are allowed without the use of pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall package sizes: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. The enlarged cargo place is formed when transporting the consumer of two or more rolls.

Packing tools are:

- Katya with a diameter of 6.5 mm in OST 14.15.193;

- straps of wire according to GOST 3282 or by OST 14-4-210;

- strapping from tape according to GOST 3560;

- Wire and tape for another NTD.

Package mass - no more than 1 tons.

Grids are transported by transport of all types in accordance with the rules for the carriage of goods acting on the transport of this species and the technical conditions of loading and fastening of goods * approved by the Ministry of Communications. Transportation by rail is made by writing or small shipments. On an open rolling stock, the grid is transported only by packages.
________________
* Probably the error of the original. You should read: "Technical Conditions of Loading and Fastening of Cargo." - Note database manufacturer.

The conditions for transporting the grid in terms of the effects of climatic factors must comply with the conditions of storage 5 and 8 according to GOST 15150.

(Modified edition, change. N 1, 2, 3).

5.6. Storage of grids must comply with the conditions 5 according to GOST 15150.

(Modified edition, meas. N 1).

Appendix (Reference). Table of living section and theoretical mass of 1 sq.m mesh

ATTACHMENT
Reference

Table of live cross section and theoretical mass of 1 m nets


Cell shape	Grid number	Wire diameter, mm	Live cross section mesh,%	Mass 1 m nets, kg
Rhombic



Rhombic or square






Square

Note. The values \u200b\u200bindicated in brackets are distributed on mesh with a square cell.

(Modified edition, meas. N 2, 3).

The text of the document is drilled by:
official edition
Metal grids. Types.
Specifications: Sat. Gostov. -
M.: IPK Publishing Standards, 2003

Interstate standard

Technical conditions

Official edition

Standinform

Interstate standard

Steel Wicker Single Mesh

Technical conditions

Single Woven Steel Wire Cloth. Specifications.

ISS 77.140.65 OKP 12 7500

Date of introduction 01.01.82

This standard applies to steel wicker single meshs with rhombic and square cells made by plexus in one pressing of flat spirals made of steel wire and used for fences, thermal insulation works, mounting mining machines in mines and mines, sieving materials.

1. Basic parameters and sizes

1.1. The grid is divided into the form of cells:

rhombic - P (the sharp corner of the rhombus should be 60 °) - damn. one; Square - damn. 2; By type of surface: without coating,

from wire galvanized - 0.

Grids according to the accuracy of the cell size are divided into groups 1 and 2.

(Modified edition, change No. 1, 2).

1.2. The size of the side of the cell in the light and the diameter of the wire must match the specified in Table. one.

Table 1

Continuation of table. one

With a rhombic or square cell

With a square cell

2.5 mm; No. 50 from the wire with a diameter of 2.5 mm; No. 80 from the wire with a diameter of 3.0 mm and No. 100 of wire with a diameter of 4.0 mm.

Prior symmers

Mesh with rhombic cell number 12, of thermally untreated wire, diameter

1.6 mm, groups 1:

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with a square cell number 20, from galvanized wire, with a diameter of 2.0 mm, groups 2:

Grid 2-20-2.0-0 GOST 5336-80

Grid with square cell number 20 Lightweight wire with a diameter of 1.8 mm:

Grid 20-р GOST 5336-80

1.3. The limit deviation for the average arithmetic size of the sides of the cell should not exceed + 6% for the grids of the 1st group and + 10% for the grids of the 2nd group.

1.4. The limit deviation of the corner of the cell from the nominal should not exceed ± 10 °.

1.5. The width of the grid and the limit deviations must correspond to the specified in Table. 2. Mesh No. 15 of the wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

(Modified edition, change No. 1).

2. Technical requirements

Grids of the 1st group should be made of wire with minus limit deviations equal to the sum of absolute values \u200b\u200bof limit deviations.

(Modified edition, change No. 1, 3).

2.2. Each helix should consist of one wire.

2.3. Related spirals should be woven into each other with all the turns without skipping.

2.4. The grid should not be inverted spirals.

(Modified edition, change No. 2).

2.5. The ends of the spirals on both sides of the grid must be cut and each end at the junction site should be bent to its helix.

2.6. Grids after manufacture are coagulated in rolls. The roll should consist of one piece of mesh at least 5 m long for grids No. 5-60 and at least 3 m for grids No. 80, 100.

It is allowed to roll rolls from two pieces that are crosslinked by a spiral.

For grids of the 1st group, a roll should consist of one piece of at least 10 m long for grids No. 5-60 and at least 5 m for grids No. 80, 100.

(Modified edition, change No. 1, 2).

2.7. Roll mass should not exceed 80 kg. For grids No. 80 and 100, an increase in the mass of the mesh roll to 250 kg is allowed.

(Modified edition, change No. 1).

3. Rules of acceptance

3.1. Grids are accepted by parties. The party should consist of grids of one number, one width, one material and is decorated with one quality document. The document on quality must contain:

conditional grid designation;

width in millimeters and mesh length in meters, total net in square meters;

the number of rolls in the party.

(Modified edition, change No. 1).

(Modified edition, change No. 2).

3.3. Upon receipt of unsatisfactory test results, at least one of the indicators on it is re-conducted on a double number of rolls.

Results of re-checks are distributed to the entire batch.

(Modified edition, change No. 1).

4. Test methods

4.1. The quality of weave and the bending of the ends of the spirals is determined visually when the grid rolls are rewound.

4.2. The average arithmetic value of the sides of the cell side in the light is determined in three places of the grid that are not less than 100 mm from the edge, counted in two directions in parallel to the sides of the cell of 10 cells for grids No. 5-15 and 5 cells for grids No. 20 -100 and measure the length of the site, including one extreme wire, on which the countdown cells are located. The length of the area to determine the average arithmetic value of the sample side of the cell in the light is measured by a meter or a ruler with a division of 1 mm.

The average arithmetic value of the size of the sides of the cell in light (a), mm, is calculated by the formula

where i is the length of the area on which they are sequentially counted in the respective directions of 5 or 10 cells, mm; n - the number of counted cells; D - Nominal wire diameter, mm.

The final value of the average arithmetic size of the sides of the cell in the light is defined as the arithmetic average of six dimensions.

4.3. The wire diameter is measured by the micrometer according to GOST 6507 before making the grid.

(Modified edition, change No. 2).

4.5. The angle of the cell is checked by a tilt of GOST 5378 or a template in three places of the grid, but not closer than 2 cells from the edge of the mesh.

5. Packaging, Marking, Transportation and Storage

5.1. Each mesh roll must be tied with low carbon wire with a diameter of 1.2-2.5 mm according to GOST 3282 or TU 14-4-1563 or the waste of this wire in the middle and on the edges or end of the mesh web should be suspended the same wire to roll in the middle and by edges.

(Modified edition, change No. 1, 3).

5.2. The ends of the roll should be wrapped with paper according to GOST 8828 or other paper made according to regulatory and technical documentation, or packaging cloth according to GOST 5530, or a tare cannon, or glued web, or a cross-wing flap from the textile industry, as well as other materials manufactured by According to regulatory and technical documentation, excluding the use of cotton and linen fabrics and not worsening the quality of the packaging.

Mesh No. 5-50 is allowed inclusively not packaging, but be sure to tied crucifably the ends of the wire roll in accordance with clause 5.1 or another method of driving a roll, subject to preventing the clutch of the cooled wires.

Packaging materials on the ends of rolls are tied with wire in accordance with clause 5.1.

Packaging of the grid transported to the regions of the Far North and equivalent to them area must correspond to GOST 15846.

(Modified edition, change No. 1, 2).

5.3. At the request of the consumer, the grid is covered by conservative Lubrication of the HCR for the approved technical documentation or a mixture of HCB and industrial oil according to GOST 20799 in a 1: 1 ratio.

5.4. To the end of the roll or package must be attached a shortcut that indicates:

trademark or name and trademark of the manufacturer;

name and trademark of the manufacturer;

conditional grid designation;

the width is in millimeters and the length of the grid in meters, the total amount of the grid in square meters.

5.3-5.4. (Modified edition, change No. 1).

5.4A. Transport markings - according to GOST 14192.

(Introduced additionally, meas. No. 1).

5.5. The grid is transported by packages according to GOST 26663 or rolls. Packages are allowed without the use of pallets.

Packing tools are:

katya with a diameter of 6.5 mm by OST 14.15.193;

strapping from wire according to GOST 3282 or in OST 14-4-210;

strapping from tape according to GOST 3560;

wire and tape on other regulatory and technical documentation.

Package mass no more than 1 tons.

The conditions for transporting the grid in terms of the effects of climatic factors must comply with the conditions of storage 5 and 8 according to GOST 15150.

(Modified edition, change. No. 1, 2, 3).

5.6. Storage of grids must comply with the conditions 5 according to GOST 15150.

(Modified edition, change No. 1).

ATTACHMENT

Reference

Table of live cross section and theoretical mass of 1 m nets

Grid with a rhombic or square cell

Square Cell Mesh

Note. The values \u200b\u200bindicated in brackets are distributed on mesh with a square cell. (Modified edition, change No. 2, 3).

Information details

1. Designed and introduced by the Ministry of Metallurgia of the USSR

2. APPROVED AND INTRODUCED RESOLUTION OF THE STATE COMMITTEE OF THE USSR on standards from 31.03.80 No. 1466

3. Instead of GOST 5336-67

4. Reference regulatory and technical documents

	Point number
GOST 3282-74
GOST 3560-73
GOST 5378-88
GOST 5530-2004
GOST 6507-90.
GOST 8828-89
GOST 14192-96
GOST 15150-69
GOST 15846-2002.
GOST 20799-88.
GOST 26663-85
OST 14.15.193-86
OST 14-4-210-87
TU 14-4-1563-89

5. Restriction of the validity period of the action of the USSR State Standard from 08.04.91 No. 457

6. Edition (March 2007) with amendments No. 1, 2, 3, approved in September 1986, March 1989, April 1991 (IUS 12-86, 6-89, 7-91)

Editor M.I. Makashova technical editor L.A. Guseva Corrector A. S. Cherniusova Computer layout I.A. Tyclina

Signed in printing 19.03.2007. Format 60 x 84 1 / s. Offset paper. Guard Times. Print offset. Hood. PEC.L. 0.93. Uch.-izd.l. 0.75. Circulation 56 copies. Zack. 254. Since 3840.

FSUE "Standinform", 123995 Moscow, grenade lane., 4.

Vacated in FSUE "Standinform" on the PEVM.

Printed in the branch of FSUE "Standinform" - type. "Moscow Printer", 105062 Moscow, Lyalin Per., 6.

OST 14.15.193-86

OST 14-4-210-87

TU 14-4-1563-89

5. Restriction of the validity period of the action of the USSR State Standard from 08.04.91 N 457

1. Basic parameters and sizes

(Modified edition, change. N 1, 2).

1.2. The size of the side of the cell in the light and the diameter of the wire must match the specified in Table 1.

Table 1


Cell shape	Grid number	Nominal side of the side of the cell in the light, mm	Nominal wire diameter, mm
Rhombic


Rhombic or square



Square

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with a square cell N 20, from galvanized wire with a diameter of 2.0 mm, groups 2:

& nbsp.Grid 2-20-2.0-0 GOST 5336-80

Grid with square cell N 20, lightweight, from wire with a diameter of 1.8 mm:

& nbsp.Grid 20-р GOST 5336-80

1.3. The limit deviation for the average arithmetic size of the cell side should not exceed + 6% for group meshes 1 and + 10% for group 2 grids.

1.4. The limit deviation of the corner of the cell from the nominal should not exceed ± 10 °.

1.5. The width of the grid and the limit deviations must correspond to the specified in Table 2.

Grid N 15 from wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2


Grid number	Width, mm.	Limit deviations, mm
			group 2.

		1.12 cells
	1000, 1500, 2000
			1.6 cells
	2000, 2500, 3000

(Modified edition, meas. N 1).

2. Technical requirements

2.2. Each helix should consist of one wire.

2.3. Related spirals should be woven into each other with all the turns without skipping.

2.4. The grid should not be inverted spirals.

(Modified edition, meas. N 2).

2.5. The ends of the spirals on both sides of the grid must be cut and each end at the junction site should be bent to its helix.

2.7. Roll mass should not exceed 80 kg. For grids NN 80 and 100, an increase in the mass of the mesh roll to 250 kg is allowed.

(Modified edition, meas. N 1).

3. Rules of acceptance

4. Test methods

4.1. The quality of weave and the bending of the ends of the spirals is determined visually when the grid rolls are rewound.

4.3. The wire diameter is measured by micrometer GOST 6507. Before making a grid.

(Modified edition, meas. N 2).

4.5. The angle of the cell is checked by a tilt GOST 5378. or template in three places of the grid, but not closer than two cells from the edge of the grid.

5. Packaging, Marking, Transportation and Storage

5.1. Each mesh roll must be tied with a low carbon wire with a diameter of 1.2-2.5 mm by GOST 3282. Or that 14-4-1563 or the waste of this wire in the middle and at the edges, or the end of the mesh web should be tied to the same wire to roll in the middle and at the edges.

(Modified edition, meas. N 1, 3).

5.2. Ends of the roll must be wrapped by paper GOST 8828. or other paper made on regulatory and technical documentation (NTD), or packaging cloth GOST 5530. , or tare cannol, or glued web, or cross-wing flap from textile industry, as well as other materials made on NTD, excluding the use of cotton and linen fabrics and not worsening packaging quality.

The NN 5-50 mesh is allowed inclusively not packaging, but be sure to tie the cross-shakers of the wire roll in accordance with paragraph 5.1 or in another way, subject to preventing the clutch of the cooled wires with each other.

Packaging materials on the ends of rolls are tied with wire in accordance with paragraph 5.1.

The packaging of the grid transported to the areas of the Far North and hard to reach areas must correspond GOST 15846..

(Modified edition, change. N 1, 2).

5.3. At the request of the consumer, the grid is covered with conservative Lubrication of the LCB according to the installed manner or a mixture of HCB and industrial oil by GOST 20799. In a 1: 1 ratio.

5.3-5.4. (Modified edition, meas. N 1).

5.4A. Transport markings - by GOST 14192..

(Introduced additionally, meas. N 1).

5.5. Mesh transport packages by GOST 26663. or rolls. Packages are allowed without the use of pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall package sizes: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. The enlarged cargo place is formed when transporting the consumer of two or more rolls.

Packing tools are:

- Katya with a diameter of 6.5 mm in OST 14.15.193;

- Wire strapping on GOST 3282. or by OST 14-4-210;

- strapping from ribbon GOST 3560. ;

- Wire and tape for another NTD.

Package mass - no more than 1 tons.

Grids are transported by transport of all types in accordance with the rules for the carriage of goods acting on the transport of this species and the technical conditions of loading and fastening of goods * approved by the Ministry of Communications. Transportation by rail is made by writing or small shipments. On an open rolling stock, the grid is transported only by packages.
________________
* Probably the error of the original. Read: "Technical Conditions of Loading and Fastening of Cargo" . - Note database manufacturer.

The conditions for transporting the grid in terms of the effects of climatic factors must comply with storage conditions 5 and 8 GOST 15150..

(Modified edition, change. N 1, 2, 3).

5.6. Storage of grids must comply with the conditions 5 GOST 15150..

(Modified edition, meas. N 1).

Appendix (Reference). Table of living section and theoretical mass of 1 sq.m mesh

ATTACHMENT
Reference

Table of live cross section and theoretical mass of 1 m nets


Cell shape	Grid number	Wire diameter, mm	Live cross section mesh,%	Mass 1 m nets, kg
Rhombic



Rhombic or square






Square

We offer to buy a grid woven steel "Rabita" (stainless, galvanized and ordinary) at a bargain price per meter m2, in Moscow and the region with delivery throughout Russia.

A wide range of Rabits Mesh application makes it almost the most demanded and indispensable in construction. The price of the grid woven directly depends on the thickness and size of the cell. Sale of steel grid with delivery is one of the priority activities of our company.

Metal Mesh Rabs Sort

Name / size, mm.	Price meter (m2)
Grid 10x10x1 Rabita	128,10
Grid 15x15x1 Rabita	87,41
Grid 15x15x1.2 Rabita	99,75
Grid 15x15x1.4 Rabita	141,35
Grid 20x20x1.2 Rabita	75,20
Grid 20x20x1.6 Rabita	115,29
Grid 20x20x2 Rabita	160,22
Grid 25x25x2 Rabita	143,25
Grid 45x45x2 Rabitz otsink.	contractual
Grid 50x50x1.6 Rabita	48,50
Grid 50x50x1.8 Rabita	66,18
Grid 50x50x2.5 Rabita otsink.	call
Grid 50x50x3 Rabita otsink.	163,53

Grid Steel Rabita - Application and Classification

Steel wicker grid is one of the most popular and recognizable metal rolling market segments. Literally any fence - from private possessions to industrial zones and partitions of various purposes, made of steel wicker grid. Fences, and not only, a steel wicker grid, which in the company "Rent Metal" can be at a bargain price, applicable in various fields:

Construction - as a strengthening frame when carrying out insulation, as a sieve for sieving building materials, to harden the road asphalt coating, the manufacture of reinforced concrete, low-loaded structures;
Mining workings - strengthening mines and mines, as well as sifting - separation of materials according to fractions;
Agriculture is the manufacture of cells, enclosures and partitions, for rabbits and poultry houses.

Rabita grid, price On which the meter is listed, can be supplied in Moscow and an uncoated area, with zinc or polymer coating. The protection of the grid on the external environmental impact allows you to successfully exploit it during the decade without changes in the appearance. Corrosion resistance, temperature drops, manufacturability and ease of installation - steel mesh is very widely and the possibilities of its use are constantly expanding.

Grid Steel wicker GOST 5336-80 - Production and characteristics

GOST is classified a steel woven grid according to the accuracy of the sizes of cells, coating and on the form of a cell. The grid is a canvas with square or rhombic (rhombus angle 60 °) cells, a retainer of flat or round spirals, woven each other in a consistent order. Production material - low carbon steel wire, thermally untreated or galvanized. Protective zinc coating is applied in several ways - hot or galvanic. Hot dip galvanizing is performed in stages - cleaning, degreasing, flushing and drying, then immersion in the bathroom with zinc. The steel sheet coated in this way is used for a wide range of construction work and is characterized by durability and immunity to corrosion.

The electroplating coating is the application of the zinc layer by the method of electrochemical exposure to the metal, as a result, the coating is obtained even, without the slightest defects and retains the initial appearance for a long time.

It is made of wire with a cross section from 1.2 mm to 5 mm, quality requirements: adjacent spirals are woven with all the turns, there are no inverted spirals in the grid. Rolls are shipped by weight of no more than 80 kg, the mass of the roll is allowed 250 kg for some types of grids. Roll length no more than 10 meters, in agreement with customers it is possible to individual order, the roll width is up to 1.5 meters. The ends of the roll turn around either with a web, or paper, rolls are tied with a wire-rod or ribbon.