Highchair for feeding from wood with your own hands. Woodchair from wood with their own hands: easy, simple and fast. Normal Wooden Chair

With the advent of the baby on the light of his parents there is a lot of worries. One of them is the acquisition of a chair for feeding. Meanwhile it is worth it in children's stores is quite expensive. In order to save on his purchase, you can try to make a chairs for feeding with your own hands. By and large there is nothing complicated here. The main thing is to adhere to the recommendations presented, act step by step and carefully examine the drawing.

The main thing is what you need to remember, making a chair for a child - security. The design should be durable and stable.

Making a wooden chairs

Before making a chairs for feeding, the following tools and materials should be prepared:

saw;
a hammer;
bars with a cross section of 400x200 mm;
board (thickness 20 mm);
sheet dvp;
nails;
batting;
sucks;
the cloth;
glue;
brush;
sandpaper;
gloves to protect your hands from the heads during the work;
plywood.

Also, you will also need to purchase paintwork material. But you need to choose non-toxic. This is suitable that has an acrylic basis. Such paints are modern and safe.

Back to the category

Stage 1: Made the details

Starting to keep the chair for feeding is necessary with the manufacture of parts for it. It will be necessary to do the following:

4 legs (length 390 mm);
2 lower crossbars (length 340 mm);
3 crossbars (length 300 mm);
top crossbars (length 220 mm);
1 small countertop (dimensions 200x340 mm);
4 rounded elements.

To make such details, you need to take bars and cut them in half. Of these, legs are first created, then the upper and lower crossbars, and then cross. They will be required to be treated with sandpaper to eliminate the appearance of the head of the baby, because it will grab his handles for all the details of the chair.

Now you can go to the creation of rounded items for the sidewall. They need to be cut out of the board to get the most durable and reliable highway, the drawing of these parts is represented.

It will be necessary to make such marking on a wooden board. The diagram should be drawn so that the fibers of the material are located perpendicular to the corner of the fold. Then the finished item will not lose its strength over time.

The back and seats need to be cut out of the fiberboard. From it will need to make 6 parts. Their size should be as follows, 300 * 250 mm. Two corners of them must be rounded. The ends of such details will need to care carefully. After that, it will be necessary for 3 identical parts to glue with each other, and then put under the press. And the last thing you need to do is cut out a plywood countertop. Its size should be like this: dimensions 200x340 mm.

Back to the category

Stage 2: We produce stool assembly

Now you can start collecting a chairs for feeding. Previously need to make rectangular waders. They are cut out of wood. Their size should be 8 * 20 * 50 mm. Under them in detail, you will need to make holes in a depth of up to 40 mm.

They will need to fix them on glue, and then additionally on nails. But it will be necessary to draw their hat into the wood surface - this will eliminate the occurrence of injuries and cuts in the child.

Start collecting a chairs for feeding follows from the sidewall. It consists of 2 rounded parts, legs and lower crossbars. First of all, 2 last details are recorded with the help of glue, ducts and nails. It is necessary to ensure that the compound occurs at an angle of 90 degrees. Then you can collect the upper crossbar and 2 roundabouts. The second sidewall will need to be made similar to the first. At the same time, during the assembly, it will be necessary to compare both items several times, with the aim of ensuring that they are obtained identical. Created sidewalls will be required to handle the sandpaper.

Next, you will need to combine the seat and back. Here you can use screws and corners. After that, it will be necessary to wait, when the glue on all parts is completely dry, and then you can collect the entire highchair.

The sidewall is connected by plank-across (length 300 mm) and dwarfs. Previously need to do the holes for them. Then additionally the design is fixed with nails. Then you will need to attach the legs to the lower and top straps, and then install the crossbars. From one of the ends, a tabletop is fixed.

After that, the finished design is additionally processed by sandpaper. Then it is covered with paint and varnish material and left to dry. Then you will need to cover the seat and back with a cloth. But it will first be necessary to pave the batting under it and consolidate it with its stapler. Such a casing will allow the baby with the maximum comfort to sit on the chair. On this work on its creation will be completed. So, you can use the finished product for its intended purpose.

Back to the category

How to make a mobile chair for feeding?

It is not always possible to take a wooden chair for feeding a child. After all, it is large enough and cannot be transported. And here many parents may have a question: how to make a mobile highchair for feeding with their own hands? Here, too, without a step-by-step instruction can not do. But it will first be necessary to prepare the following:

fabric (cotton, flax, lining fabric) - about 3 m;
slings - 2.5 m;
karabina buckle - 3 pcs;
thick and durable braid - 3 m;
scissors;
needles;
threads;
sewing machine.

One of the positive moments in favor of wooden furniture is what is really to make a wooden chair for feeding with your own hands. Naturally, in the case of twins you will have to do two chairs at once. Note that usually homemade children's chairs for feeding from wood are different - classic folding, transformers and growing.

In this article in the style of "for dummies" we will tell how to make a chair for feeding with your own hands on the example of a wooden chair-transformer. We will show two working options for feeding with their own hands with drawings and sizes, as well as conduct some considerations about their occasion.

ATTENTION!!! The article turned out long, as we write not only for experienced masters, but also for beginners, as well as people who rarely make something with their own hands. If there is no desire to read everything - use the table of contents. Pop-up headlock tips will help you understand what is there, and choose the desired one.

If you want to make a chairs for feeding with your own hands, but not a transformer, or everyone knows how to do and love brevity, also not trouble. Over time, at this place will be a link to the entry, where information about homemade stools for feeding will be collected in one bunch. In the meantime, we look at the site map and heading, there are articles there.

The content of the article:

Highchair for feeding with your own hands - why a children's wooden chair transformer. MOTIVATION

One of the great advantages of children's wooden transformers for feeding is that the design of the chairs to the limit is simple, so they can really construct themselves even a newcomer. You can make such a chairs for feeding with your own hands either from the girlfriend, or without any problems to purchase the material at a small price.

In the article, a children's chair for feeding with their own hands, we considered in detail how the folding chair was made for feeding. It turned out that he was pretty simple. That's just his relevance is very doubtful - wooden furniture is always bulky and heavy, and in two years such a chairs will have to be disassembled on parts and make a separate children's table and a chair.

But the chair - the transformer immediately "kills" two hares: he and a chair, and the table - the party. At first, the chair is used in direct appointment, together with a small table, and then, after 1.5 years, it is understood, and the child has a separate desk and highchair. Convenient and practical. Perhaps this is exactly what is constant interest in the Wooden Stulcher to feed the feeding made with his own hands.

It remains only to figure out how such a miracle of technology make themselves. And at the beginning, let's see the video of one of the craftsmen.

Feeding chair with your own hands or a wooden chair transformer for feeding a child with your own hands start work

Searching in the Internet on the topic of a feeding chair with your own hands, it will become clear that there are two variants of the transformer chairs.

The first option is more complicated, but it is for some reason that he is popular on the Internet. Most likely, once someone made a wooden chair transformer for feeding with his own hands in this way, and then the articles on how to make it independently miraculously unfortunately. Because where to take the correct option is not clear. We give here the most understandable (for the author) description and sane drawings.

The second version of the chair for feeding with their own hands is simpler and logical, it is according to it that are made by factory wooden transformers. And we also give it here with our own measurements.

If everything is clear with the material and interest to the stool for feeding with their own hands only drawings and sizes, then immediately go below to parts how to make a chair for feeding with your own hands - option 1, and how to make a children's wooden chair for feeding with your own hands - option 2. Ah So far, since they decided to keep a story in the style of "for teapots", then let's talk about the materials used.

Highchair for feeding with your own hands - Materials

To make a chairs for feeding with their own hands, wooden bars will be required. A boards can be added with a thickness equal to the thickness of the bar. Plywood or LDSP, selflessness, glue, tissue washing upholstery and any soft filler. Well, still brackets for the construction (furniture) stapler.

A timber can be used by any, which is sold or is in the presence. It would be better that he was oversized. So it is less than about it. Otherwise, he will have to the pussy himself and do smooth. It is convenient to take the size of a bar of 20x30 mm.

As a tabletop for the table, the desktop and a small removable table for feeding for feeding will go litsp or thick plywood - from 10 to 15 mm thick.

Solid pieces of the back and seating of the chair for feeding with their own hands can be made of fiberboard or plywood. Faneur does not have to use thick, enough from 5 to 10 mm thick. In general, the plywood will be stronger, but in the Fiberboard it is easier to enter a staple bracket.

Some details are glued together. To do this, you can use carpentry or just glue PVA.

To make a soft back and seat chairs for feeding with your own hands, it will take an external upholstery - a durable easily washing fabric, such as a cloak or bologna, or just a glued, and inside a soft filler - foam rubber, batting or something else. Quantity See yourself how much you need. The soft filler can be glued to the solid parts of the back and seats, or simply begged it with a construction stapler, and you can combine both options. The upholstery is easier to fix it right away. So it will be more reliable. The size of the bracket depends on the stapler and the selected soft upholstery thickness.

It is still nice to have an average sandpaper, for the sump of the details and give it smoothness.

In the first version of the chairs for feeding with their own hands, only 4 tree screws are used: for attaching the table top to the desk. All other wooden parts will be connected to homemade drains, also from wood. You can put the remnants of bars.

In the second version of the chair for feeding with their own hands, there is practically no dumb, but there are many self-tapping screws to fasten all parts of each other. Factory transformers are made on the euro of self-drawing, and a children's wooden chair transformer for feeding with their own hands can be collected on any. The main thing to collect correctly. Sucks are used only if you decide to make rounded items that are conveniently fixed to the bars with their help.

In both versions of the wooden table and the chair for feeding with their own hands there are rounded elements, although you can do without them. These elements can be made either from the boards with a thickness of the corresponding thickness of the bar used. If the bar is taken, as here, 20x30 mm, then the board takes a thickness of 20 mm, but you can and 30 mm, it, depending on how you put the bars, joke g). If there are no boards, then the same bars are perfect. Only they need to glue together.

Depending on how much and how you place the rounded items for cutting on the board or glued bars, the length of them (boards, bars) and you need to take. On glued bars or board, it is necessary to put 4 elements at once. Therefore, the length will be from 0.5 to 1 m, and maybe 2 m are not enough.

Feeding chair with her own hands - Separate words about wood and paintwork

I propose to pay attention to the stool tree material for feeding. Immediately, we note that the children's wooden chair for feeding with their own hands is best made from the linden. However, like any other children's furniture for kids. Since the coniferous breeds are often used in the manufacture of wooden furniture. The trees can not approach: pine highlights a resin that is very toxic. And child health is better not to risk. However, in construction stores often lies with pine, therefore we try to take as dry as possible and without intelligence of the resin. Believe me, the child will be better, and you yourself do easier.

To impart brilliance, color and environmental protection, it is better to use acrylic varnish, or paint. It is not so harmful to the baby, like the rest. Why he is he? Answer - what if the kid will try a table or a chair for feeding, which you yourself made your own hands? For the consequences to answer you. Although if it does not care if you have it possible to get them, then you can cover the feeding chair with your own hands than it will want.

Children's chair for feeding a wooden transformer with their own hands - Option 1

For understanding that he will represent the highchair for feeding with their own hands in the form of composite parts of option 1, give drawings and sizes.

To make parts of a children's highchair for feeding a wooden transformer with their own hands, we take the timing with a cross section, for example, 20x30mm. From it we will do the following details. Indicate the length and quantity.

Legs - 390 mm, 4 pcs.
Rounded parts - 4 pcs.
Armrests, they are the top of the high chairs - 195 mm, 2 pcs.
Planks, walking parallel to armrests, they are crossbars, 335 mm, 2 pcs. On these crossbars, then we will clipped the seats with the crossing chairs for feeding
Planks on which the seat and back are attached, they are accepted - 300 mm, 3 pcs. Two for seating and one for the back
A small table on the chair (in X W) 340x340 mm. It lies on the armrests of the chair 340 mm \u003d 300 (the length of the stool is the chair) + 20 + 20 mm.
The seat and the back have the same dimensions (in x x) 250x290 mm. The width is 290 mm \u003d 300 (the length of the bar is crosslinked) - 5 - 5 (gaps on both sides for upholstery and soft filler), mm.

Legs 500 mm 4 pcs.
Planks for the lower and top of 410 mm 4 pcs. On the bottom straps, the table for feeding is worth, on the top mounted countertop.
Cross slats 340 mm 4 pcs. To bore the sidewalls of the table. Length 340 (mm) \u003d 300 (length of chairs) + 20 + 20 (mm). So done so that the chair gets up between the sidewalls of the table.
Countertop (in x W) - 440 × 380 mm. 1 PC. The tabletop lies on the upper boards and is not issued beyond the limits of the sidewall. Width 380 (mm) \u003d 340 (transverse strip length) + 20 + 20 (mm). Length 440 (mm) \u003d 410 (Top Planck Length) + 30 mm

How to make a chairs for feeding with your own hands

Begins work from the chair. For this, according to sizes, the desired length of the bars are fixed. Separately, you need to make rounded parts - they connect legs and armrests in front and rear. Naturally, all dug details need to be made smooth, without a pile and with special care to treat emery paper - small children are always increased injury. Danger. Therefore, to the question of how to make a chair for feeding with your own hands, we give a pathetic answer - we work for conscience.

Roundings for the wooden chairs of the transformer for feeding with their own hands are cut separately - according to the drawing. For rounded parts there is one important point. If you glue the bars and lay the part with wood fibers not as shown in the figure, then such a part when drinking, or further operation can be mad at the most unexpected way. Therefore, the bars need to glue with wood fibers in parallel to each other. And it is necessary to have a rounded part of the chairs for feeding with your own hands along these parallels. The same goes and the board - the part for drinking, we have parallel wood fibers.

To successfully glue the bars using joiner and pva. Additionally, the bars do not need to align. For bars, it is necessary to choose enough flat planes, correctly arrange them and just rush to the clamps. During the day, probably dried.

Then from the waste of bars for the stool for feeding with their own hands, you can make rectangular ducts. Dimensions - 8x20x50 mm. In general, the length of the sewage should be made by 4-5 mm less than the total depth of the groove of two fastened parts. The edges of the sewage can be slightly rounded.

On all the details place places for landing the wanks. To do this, it is necessary to place the contours of the groove, for example, a pencil. Rectangular grooves for the wrenches need to make a depth of about 30 mm. To do this, drill a drill with a diameter of 6 mm 4-5 holes. Next, with the help of the chisels, align the walls of the groove and fit under your own, individual, homemade wanks. And if there is a milling mill, then the grooves make a mill, so easier.

When all the details are ready, there are seas and grooves for fastening, you can start assembling the children's chairs for feeding a wooden transformer with your own hands.

Wooden chair transformer for feeding a child with her own hands - assembly

Wooden chairs Transformer for feeding with their own hands begin to collect with sidewalls. First one is done, then the second. On the wanks to draw in the middle of the length line. Using a light hammer to install to the lined line. Then we take the part connected and insert the wanks into it. We connect the details at first to dry, i.e. without glue. After all the details of the sidewall are connected, check for the presence of slots. If everything is fine, we gently divide the parts and sample the ducks, and then we collect again, as described above. Then you need to pull the items and give dry, about 1 day. You can roll with clamps, or firmly wind up with a rope from two sides. But at the same time to look so that nothing has twisted, and there were no cracks. Rope is less reliably than clamp, but not everyone has clamps of such sizes.

So far, the sidewalls of the chairs of the transformer for feeding the child can be done by doing their own seats and backs. They are cut out of plywood or fiberboard, according to the drawing. If the plywood is not thick or used fiberboard, then it is better to cut 3 parts of the seating and back and glue them with each other. We wash glue and clamp the clamps. Such a day.

After the sidewalls, the seat and back are assembled and cut, we collect everything finally. On the seat and back with the planned reverse side of the wooden chairs of the transformer for feeding a child with their own hands, you can immediately attach the planks crossing. To do this, use either the seasons, or what will be even easier, small self-tapping screws. In order to succeed normally, the planks should be fixed with gaps of 5 mm on each side of the width of the seating and the back. The back and seat can be combined with a metal corner, or bent along the metal strip.

If we do on the sewage, then in the seat drill holes for fastening to the cross the chair. Bashed better on 4 pcs. Standard cylindrical waders. For the back of such waders - 2 pcs. We connect the sidewalls by crossings on which the seat will fall. We do without glue to check and see the positions of the seat and back. Also without glue, we plant the seat on the crossbars on the seasons. Flexing and flexing the back, mark the position of the bar for fixing the back, then disassemble. If there is a desire, you can cut the side bar for the back according to the drawing. There is no desire - everything will be fine too.

At the children's chair for feeding a wooden transformer with their own hands we are wearing a sidew and a back of a soft filler: glue it to a solid part or nailed with a stapler. Then with again with a stapler, stretch the upholstery. It is better not to save, and do not try to the upholstery and the soft part is to fix one and the same bracket. Maybe something to twist, and it will be not good.

Then we collect all the parts on the woven wrappers. We put in place, check the corners. Plank the backrest is kpripim to the back on 2 cylindrical ducts. Check the gaps and tighten with clamps or rope. We are waiting until he dries. All, chair from a wooden chairs of transformer for feeding with their own hands is ready .

We repeat. If there is no desire to mess around with the seats, all parts are actually connected using conventional screws. Perhaps it will not be so firmly, but it is easier to assemble. Deciding, of course, master. And the roundabilities are more convenient and durable to fasten with the help of the wrenches, and then thoroughly wrap them with glue. After that, leave the finished sideline on a day to dry.

The last step: cut out, according to the size of a small table on the chair for feeding with your own hands. It can be left rectangular, you can round in the part of the closest to the child. This is not fundamentally. Only the case of aesthetics and coming. This table is attached to the edges of the armrests. It is possible on cylindrical ducts, you can on self-drawing. And when the child is growing, he is simply removed and everything, he is no longer needed.

The table for the feeding for feeding with her hands is also assembled as a chair. At the beginning of dry, then with glue. Used either homemade drums, or self-tapping screws. We start with sidewalls. We attach the top and bottom planks to the legs, two rectangles are obtained. When the sidewalls are assembled, they are, like a chair, you need to pull and wait a day while dried.

Further the transverse bars are fastened - with their help the sidewalls are connected. Scrolls for feeding table with their own hands, attacks according to the drawing. The general meaning is that they are at no distances from the edges of the sidewall. On the lower, which will be closer to the edge, stand the legs of the chair in the position of the chair for feeding. And the top serves as strips for the legs of the chair, so that the chair stood is firmly.

Drinking from plywood or LDSP Countertop is mounted on top of the top pieces of sidewall and screwed up with self-draws. Everything is going together and tightened as usual, we wait until dried.

When the table is ready for feeding chair, turn it into a stool transformer for feeding a child. To do this, connect them. The table turns over, the countertop turns out to be behind, and the chair is put on the transverse planks of the table.

Table Transformer For Feeding a Wooden Wooden DIY - Latest Strokes

Finally, when the chair and a table are ready, for the last time we check for roughness and squeak, if they found it.

When the chair and a table of a transformer for feeding a child's wooden hand are made with their own hands, they should be fully stirred - varnishes to use exclusively non-toxic, or paint acrylic paint. To pre-give the desired color you can rip and dry.

Everything, the first option is ready. The most adequate description was found at http://mebelsam.com, from this site was taken by a note on the first option.

Children's chairs for feeding a wooden transformer with your own hands - Option 2

To understand that he will represent a highchair for feeding with their own hands in the form of composite parts of option 2, give drawings and sizes.

To make parts of a children's highchair for feeding a wooden transformer with their own hands we take the timing with a cross section, for example, 20x30 mm. From you need to do the following details: indicate the length and quantity.

Size for feeding with your own hands Size spare parts, Length and quantity

If there are no rounded parts

Legs 450 mm 4 pcs.
Armrests - 365 mm 2 pcs.

If there are rounded parts

Front legs 450 mm - 2 pcs., Rear 390 mm - 2 pcs.
Armrests - 290 mm 2 pcs.
Round item according to the scheme - 2 pcs

General

Lower strips on the sidewalls 365 mm 2 pcs.
Cross bars 350 mm 4 pcs. They attack the seat and back.
Seat (in x x) 290x330 mm
Back (in x x) 450х330 mm

Size of spare parts, length and quantity

Legs - 450 mm 4 pcs. Legs located in the middle of the table, and are the bottom straps of the sidewall.
The lower and upper crossbars, in which a table for feeding stands in the position of the desk-part, and to which the countertop is attached - 500 mm 4 pcs.
Cross slats 410 mm 3 pcs.
Countertop (in x W) 500x510 mm
Straps fastening for stool legs 230 mm. Attention - in the diagram, the thickness of the bars - 15x15 mm, but anyone can use. For example, the same 20x30 mm.

Wooden chair transformer for feeding the child with her own hands - the main differences from the option 1

The previous part about the wooden chair transformer for feeding the child with their own hands turned out to be too voluminous. Therefore, in order not to write a sheet again, let's say that everything is done according to the drawing and size similar to the first option.

The wrenches are not used, the elimination rounded parts of the chair for feeding. They are done, as in Embodiment 1, only have other sizes. Everything else is fastened on self-drawing. You can regular on wood, you can euro. If you use Eurosamores, then place the places where they should enter. And at the place with a smaller diameter, drills the hole for them.

Highchair for feeding with your own hands - make items and collect

Bruks are cut down according to sizes. Carefully processed by sandpaper. A cardinal difference from the first chairs for feeding with their own hands is the lack of special round parts. But since sharp corners are an increased danger to a small child, they need to round. A little curly on one side precisely the top parts of the knock legs. And also twist the two bottom crossbars of the table - the legs on which it is worth.

You can still in the sidewalls between the armrest and the bottom plank, to which the seat is mounted, insert several strokes, rectangular or round is irrelevant. You can accommodate them anywhere at any distance, the main thing in the area of \u200b\u200bthe seating. It is that the kid does not pack through the sidewall, and for beauty will go.

Another touch.
How to make a chairs for feeding with your own hands with a movable back? It can be done so that the back of the chair for feeding made by their own hands took several positions. You will have to tinker.

For this, the rear legs and armrests are bonded with each other with a round part, as it was in the first version. In this case, the size of the armrest and the rear legs will be others (see description of the sizes of the chair). In the roundabout you need to do a hole where the screw will be inserted into the end, with a pen - a fixer at the end. The screw is one side to the back of the chair, the other rides this hole. The handle screws out the edge and fixes it in the desired position. The back is fixed.

The hole can be made either by the mill, or make some small holes with a drill and then modify the chisel. The size of the opening depends on the screw used. The handle can be anyone you are comfortable. In the handle, we carefully choose the groove under the nut, which actually will screw themselves on the screw and fix the back of the stool. The screw itself is conveniently fixed not in the back of the chair, but in the upper cross.

Once again, we note that the rounding of the chair for feeding with their own hands is more convenient and better to fasten with the help of cursed wanks. On self-drawing will be uncomfortable and paint.

Specifically for the kid, such a version of the chair is very convenient, but to make it, you will have to make some efforts. If there is no desire, then really do without a mobile back, then it makes no sense to make a separate rounding. Just tilting the back as you and the baby are comfortable. We place the place of touching the top transverse plate of a plaque back and sidewalls. Drills there hole. We fasten the sidewall and the back of the self-tapping screw. So from each sidewall.

When the sidewalls for the children's chair for feeding are assembled with their own hands, two transverse fastening strips for seating and one on a movable cylindrical seating for fastening the back are screwed to the lower straps of the sidewall. The movable wanking means that one of the grooves into several (mm) is greater than the diameter of the sewage.

The back and sesidement is also made as in the first version. Only sizes here are a little others - a longer back. For the baby it is more convenient. It is also not necessarily a seat and a back to fasten each other, they are enough to attach to transverse boards, and in consequence to make soft and cutting, for example, with a glue. Before the upholstery, as usual, whirlpool and paints.

All, highchairs for a children's wooden transformer for feeding with their own hands is ready.

Hand-up table for feeding with your own hands

The table for the feeding for feeding with their own hands is going in the same way as in the first version. First sidewalls. When the sidewalls are assembled, they are bonded between themselves transverse straps located below - they also serve as supports on which there is a chair in the assembled form. This is important, since they are installed on them, and it plays a role in its solid installation.

This is distinguished from the previous version - in the middle at the bottom of the table there is no extra crossbar, which makes the table not closed, and a more comfortable child to sit behind him. At the same time, two crossbars go only from the bottom, where the countertop is attached - cross-one. When everything is collected, it remains to scout a worktop.

There is one point here.
How to make a table top for a transformer chairs for feeding with their own hands? The figure is given a scheme and dimensions of the option with grooves. For simplicity, the table top for feeding with their own hands can be simply placed on the bars, and they can be done in the factory - to hold between the bars. The first option is easier, but the self-tapping screws will be visible at the most suitable place. The second will require more about it, but more beautiful. To hold between bars, you need to make grooves in them. This is done without any problems with a mill, or just a bit, but it is longer in time. Accordingly, the sizes of the countertops will be different. The groove is washed away to do in the thickness of the table top and a depth of 5 mm.

For greater stability of the stool standing on the table, in the assembled form of a children's chair for feeding a wooden transformer with their own hands, you can additionally make four small lumps - two on each side. They are located under the table top, it is better to put them on the "fact". Those. When the table and chair are ready, put a chair on the table above, as it should be in the end. Location from the inside on the sidewalls of the table, where the legs of the chair are held closest to the tabletop. On the sides parallel with the markup, we embarcate to the sidewalls of the table, these lumps, one on each side. As a result, it should be possible, so that the legs of the chair, closest to the tabletop, passed between these bars, and they, in turn, do not give a chair to move in different directions. This gives the chair additional stability.

A table for feeding is ready for feeding.

Highchair for feeding with your own hands - the result and some conclusions

As usual, summing up, arguing on the topic, what is easier - to keep a chair for feeding with your own hands, or buy? The answer is unequivocal - buy. Moreover, wooden transformers are very common today and are inexpensive. But there are people who want to make their own efforts and fantasy, and maybe someone did not disassemble the ruins of their building materials for a long time. Then in the way - creativity was valued at all times.

The first option, of course, the most common on the Internet, but it is not the easiest. There you have to mess around with the seasons, make the grooves, glue the details. Excellent, if there is a special large clamp, since the usual rope can squeeze the item. And the details, if not squeeze at all, it may not work at all. In short, there is a lot of freight. In addition, over time, such a product will definitely disappear, remember the old digging chairs. And your child definitely shakes the finished highchair for feeding with your own hands done by you.

The second option is not distributed online. But this chair for feeding with their own hands is similar to the factory stool transformer. Collected on self-drawing. The main thing to ensure that when assembling, the mating parts of the details stood under 90 degrees to each other and did not twist. Missed little. Only if you want to make a movable back with a rounded item, then you have to sweat.

At one time, when they wanted to make a highchair for feeding a wooden transformer with their own hands, we were known for the first option. But he seemed to be complicated. And then, when they bought a factory, found its size and realized that he was not worse, and maybe better than the first option. If I had to do another time, it would be chosen the second option.

How to make a chair for feeding with your hands video craftsmen

In principle, each craftsman makes his stool transformer for feeding with his own hands. So to speak under your needs and with your capabilities. Here are collected the most understandable and popular video. It will become clear that the timber can be of any size. The dimensions of the stool-table for feeding, can also be any. The main thing is to catch the essence of the design and sequence - how to make a chairs for feeding with your own hands.

All photos from the article

The kid feeding procedure should be the most secure and convenient as possible both for him and for mom. The highchair for meals is an original structure that is easy to turn into a place for playing or learning. Sustainable design is equipped with additional protection measures that will be removed from the cappusion from falling out and give mom the opportunity to do homemade.

So if you need this chair

Most young parents answer unambiguously - yes!

Such unanimity is due to a number of moments:

the small-sized design is supplemented with an adjustable or game, which means saving space in the apartment;
there are chairs with a perspective that can be used at least 6 years - there is no savings;

specific freedom of movements in combination with minimization of traumatic situations is a healthy psychological atmosphere;
direct contact with the baby during harvesting or cooking - rational use of time;

sitting on such a chair behind a common table, the child feels his among adults - he is calm and confident;
the kid unobtrusively masters the lessons of etiquette - an educational moment.

Plastic or Natural Materials

A wooden table and a feeding chair that appeared a few centuries ago, serves as a basic model for the production of plastic products. Is it worth saying that each material has its own amenities and disadvantages.

High chair

The product from natural material is externally beautiful, it looks good in any atmosphere and is different:

durability
durability;
ecology;
aesthetics.

The functional of wooden chairs is modest and basically lies in the possibility:

adjusting the angle of tilt backing;
transformation from a low table with a chair in a high chairs.

The disadvantages of the structure include:

bulky even in folded form that is unacceptable for a small apartment;

not always included there are covers;
the presence of faces and angles;
some difficulties in caring for the surface.

Note!
The assurances that wooden chairs for feeding are heavy and silence, do not have grounds.
The analysis showed that the average weight of the product is 8-12 kg (the mass of plastic on average from 6 to 12.5 kg).
Domestic models - "Kid", "Ksenia" cost about 2000 rubles, "Chinese" - from 5 to 18,000 rubles.
So everything is relative.

Plastic chairs

Plastic capabilities are much wider and inherent in the product:

rich color palette;
diverse execution;
the possibility of transformation into a lounger;

rounded lines that significantly reduce the risk of injury;
soft case from waterproof material.

Note!
The main drawback of the plastic product is concluded in his artificiality.
Low price and too bright paints should cause you suspicion, and you have the right to demand a quality certificate, relying on the decency of the manufacturer.

Plastic chairs have three models:

transformer - adjustable height of the chair and countertops, can be folded, change the angle of the back. When the child grows up the design is easy to turn into a separate table and chair that will become a workplace for a child;
booster - an autonomous model that can stand on the floor or attached to a regular chair;

suspended - weighs about 2 kg, due to the elongated handles and a special lever is easily attached to the tabletop and can "travel" with you and your chance.

We part for the kid

The owner will not make a major work. Billets for details can be bought in a construction store, and the missing tools ask for friends. You can choose the dimensions that will fit into the footage of the apartment, and come up with your product design and soft case.

Note!
Not having carpenter skills, you can study the design features of the product in the store before work, explore the instructions for assembling, make the necessary marks and even sketch the approximate drawing of a wooden stool for feeding, which will improve at home.

You will need such tools:

a hammer;
saw;
lobzik;
drill;
clamp;
chisel;
sandpaper;
stapler;
a hammer.

The necessary materials include:

2 cm thick for slats and roundings on the handles (so that the item is durable, wood fibers must cross the imaginary radius at an angle of 90 °);

From the same boards cut the crossbars.
Oktrut billets.
Connect the points of compounds - roundings with fragments of perilets and cross-legged with legs.
Make holes for the wanks, driving a few holes with a thin drill and adjust the size of the chisel.

Note!
Making small parts may be complex.
It will be easier to buy them in the store.
If you cut them yourself, do not confuse - the diameter of each hole must accurately match its dust.

Now you can start assembling the product:

Connect the side parts - legs with crossings. Slots put on glue.
Check that the articulation angle is correct.
Lock the clamp and leave to dry so much time as recommends instructions for use.
In the same way, connect the resulting H-shaped fragments with the top of the handrails and roundings.
Lock, give adhesion to dry.

Skill ready-made sides.
Drink a few parts of the back and seats from the List DVP -2-3 layer will give them strength.
Spread their pva.
Place under the press and leave for drying.
The side parts of the chair connect with transverse boards downstairs and at the level of the back is planted to mark the places of their connections, as well as seats and backs.

Light in the care and hygienic material, cover the seat and the back, laying under it for the softness of the foam rubber. It is possible to secure the material from the inside with a stapler.
Safety straps.
Now capital connect the lateral parts by transverse planets, where they place the seat. The back is attached to the support bar.

Treat the surface of the sandpaper and cover the lacquer.

Note!
Do not forget about the mandatory presence of safety straps for which you can use, for example, a corsage tape (sold in a sewing accessory store).

In conclusion

Highchair can make an amazing harmony in your house. Mama, being inseparable with the baby, receives certain freedom of action. Reliably recorded Chado acquires a personal space where he can eat, play, darish. Running on a small throne, the child unobtrusively adopt from parents to communicate experience.

If you do not know how to make a chairs yourself for feeding, the video in this article will help you.

When the baby appears in the house there are new items that need him. And of course, every parent wants to buy all the best for the child. And what could be better than manufactured independently. After reading our article, you can make a children's chair for feeding with your own hands. Drawings, sizes, schemes - all this will be agreed. And most importantly - it will be comfortable and safe for your baby, because you will be sure as the selected materials, and the reliability of the assembly of the whole design.

Hell for feeding with her own hands

Such a chair for feeding will need your choice when he will be six months old, and he will start to sit on his own. On the chair there is a formation of the musculoskeletal system of your baby, and its posture. It will be his first property, thanks to which he will meet the world around.

That's why the children's chairs for feeding should be not only convenient, but also useful.

General requirements

In order for this subject of furniture to be practical and comfortable, the following nuances should be taken into account:

Chair should not be soft. To the skeleton of the child develops correctly, the body should feel a reliable support. But on the feeding chair, we need relatively thin soft linings on the seat and the back.
Stool material. For a child, it is important to use non-toxic, natural, such as wood, plywood, chipboard.

Important! Do not use plastic, as it contains not always harmless substances.

Sizes of the chair. In order for your baby to feel comfortable, you need to correctly calculate the height of the back and the length, the width of the seat.

Important! There is a special table, which is compiled for children's furniture. On this table, we determine that the height of the chair seat must be 20 cm if your child's growth is from 80 to 90 cm, and the width, depth 33 and 26 cm, respectively.

Feeding chairs

The child begins to eat behind the overall table, starting with six months. Of course, it is necessary that the baby take food along with all family members. For convenience, various options have been developed, but putting the baby to the homemade stool, you must be confident of its safety.

Designs of children's chairs for feeding:

Chair at high legs - Made on long legs. Sitting into it, the baby will be on the same level with all sitting at the dinner table.
Soft case - it looks like Slim, which is attached to the usual chair. This option can be taken with you to give or visit.
Combined chair - a small chair with restrictive rings is installed at a low table.

Selection of material

For the manufacture of the chair, the wood of coniferous breeds of pine or ate. This species is quite durable and easy to process, wood texture is pleasant in appearance.

Joiner's tools:

nails, sandpaper;
loops, self-tapping screws (special connecting elements);
saw;
a hammer;
adhesive for wood;
dVP sheet, plywood;
fabric, batting or syntheps;
lacquer or paint for finishing coating, brushes.

Important! Collect the paint on an acrylic basis, and the varnishes are non-toxic on a water basis, because your baby can not only breathe them, but try tooth.

Combined highchair for feeding with their own hands

We offer a detailed description of the stages of work on the manufacture of parts and assembly of a combined chair for feeding. Here you need to make a chair and the table separately. This option assembled can be used, feeding the child behind the common table, and disassemble, you can get a child for various games and classes.

Workbathing details

The first stage is to prepare all the details for this chairs. You need to prepare such materials:

bar with a thickness of 200h400 mm - for legs and crossbars;
the board is a small thickness of 200-250 mm - to dry out armrests;
sheet Fiberboard 2x2.1 m for backrest and seat;
plywood at the worktop.

Preparation of parts for stool

For the manufacture of a chair you will need such details:

4 children legs - length of the workpiece 390 mm;
3 children. transverse bar - 300 mm long;
4 children rounded elements;
1 children. table top 200x340 mm (you can change your taste);
2 pcs. - upper crossbind size 220 mm;
2 pcs. - Lower crossbind size 340 mm.

Important! In order for your children's chair for feeding with their own hands, it is beautiful and smooth, the dimensions of the parts must accurately match the drawing.

Making parts for table

It will take:

4 legs with a length of 500 mm;
4 transverse rails Size 340 mm;
4 plates with a length of 410 mm;
plywood for tabletop sizes 380x450 mm.

Important! You can not buy all the necessary materials, you can pick up under the desired size using items unnecessary in your farm.

Now we have already reached the main stage - the assembly of the whole design. Be attentive and carefully at work, do everything perfectly, because you are trying for your child, it means that it should provide him, first of all, security and convenience.

Wood preparation:

In the production of the tree bar is cut into certain sizes. Slowing parts per dimensions, need to remove all irregularities, roughness, scratches.
Detail of the rounded element of the sidewall for the stool must be rounded with a joinery or jigsaw electric.

Important! Doing the roundings of the sidewalls need according to the drawing of a children's chair for feeding.

It is necessary to fasten with the help of a wanking (you can buy in the furniture accessories department). In extreme cases, the use of self-tapping screws is allowed.

Mounting process:

In places of attachment on a board or bar cut out or drill with a drill hole with a depth of 30-40 mm.

Important! Make holes carefully, not drilled through the details of the chair.

Connect and insert the seasons.

Build sidewall

Your chair will have two sidewalls that will fen your baby from falling. To do this, you will need for each sidewall by:

2 roundings;
2 legs;
2 top and bottom strips.

The sidewall is collecting separately each. To do this, it is necessary:

Connect legs and lower crossbar.
Secure the rounding to the upper crossbar.
Glue these two parts together.

Important! Before connecting two bars, the hole and the wanks should be lubricated with glue for furniture or pva.

The same collection process will occur for the second part of the sidewall. All items need to leave to push for a day. After - pass the sandpaper on this part of the chair to finally remove all irregularities.

Important! Carefully make sure that all the corners between the bars are straight, and the side parts are symmetrical.

Seat manufacture

We proceed to the process, it is necessary:

Cut from chipboard 6 rectangles 300x250 mm.
Round 2 corners along the long side.
Sand all edges with emery paper.
Glue 2 plates put under the press.
Fix the finished parts bent along the metal strip or fasten with screws.

Seat assembly

We proceed to the assembly of the chair, for this you need:

The sidewalls are combined with transverse boards using the sewage, as described above.
Secure the planks to support the back and plywood countertops, the same method.

Important! In order to be more convenient to fold the design, you need to outline the installation locations, drill holes and put the bars without glue. Carefully view, remove all flaws. Then you can use the glue for the final docking of the elements.

Production of table

The technological process itself is very similar to the assembly of the chair.

Collection technology table:

Attach the top and bottom planks to the legs.
Transverse bars with a length of 340 mm, copp the side parts of the table.
The sidewalls are grinding fine-grained emery paper.
Mounting countertops - you need to fasten with the end of the design.

Seat manufacture

This stage is optional, but for the comfort of your child, do not spare the material and the time spent. To do this, you will need:

foam rubber not more than 2 cm;
dense furniture fabric or colorful oilcloth;
building stapler.

We will proceed to the process, for which you need:

Cut foam rubber on the contour of the seat and backs.
Printed to chipboard using PVA.
Cut the patterns of the back and the seat, making a score to the bend 4-5 cm on the seat, and the back will need so much to cover the two sides.
On the seat to impose upholstered fabric.
Snap from four sides with brackets on the back.
To shoot the seat circumference, adjust the uniform tension of the tissue.

Important! The same techniques need to cover the seat of the seat with the difference that here you will be covered and wrapped in the case, wrapped the cloth diagonally with the envelope.

Mobile Highchair

Such a version of the chair you can take with you to give or visit. We offer you a portable (mobile) chairs for feeding, which you can sew at home, having elementary sewing skills.

With the advent, and then the growth of the child, there is a constant need to acquire new things. Many of them can be made by yourself. This will allow not only to save money, but also make it possible to make a product for your baby, which will be 100% confident. For example, if you carefully treat the selection of materials, pick up the drawings, follow the instructions, then make a children's, really good, highchair with your own hands is a very real task that forces to each parent.

What should be a chair and a table for feeding the baby?

The main requirement that concerns all children's furniture is safety. Materials must be environmentally friendly. Chairs, tables are made without sharp edges, as well as dangerous connections. In addition, small children are very active, therefore stability, the reliability of the design is of particular importance.

When making a stool, which will help conveniently feed the child, consider the following wishes:

the product must have a convenient, preferably soft seat;
the comfortable back of the chair can not be higher than the shoulders of the child, it should be soft, comfortable;
children's chair It is advisable to equip a comfortable leg support;
caring for the chair will be easier if its surface can be washed, and the upholstery material will quickly dry or possess water-repellent properties.

The easiest, as well as the economical version of the creation of a chair with a table is the retrofitting of the usual children's chair by the shelter and attaching a small table to armrests, where you can place a plate with food, a cup with juice or tea. Improving safety, such products are often equipped with trainers (with closures-carbines), which reliably fix the child.

Among parents are popular multifunctional models. For example, helping to conveniently place a child when feeding, a children's stool transformer. It consists of two parts: Actually a small children's highchair with a small table-overlay and construction, which is at the same time being the basis of a high planting and a separate children's table.

The first use option is more suitable for a child from 6 months to 2 years. On such a chair, you can simply feed the baby, putting it a plate on a small table, fixed on the stands of the chair, and you can move the entire design to an adult large table. The second method is recommended to use from 2 to 5 years. It is a separate location of children's chairs with a table. At this age, girls and boys can already do a lot on their own. Sitting for similar furniture, you can eat, draw painting, games, even learn to write.

What you need to make a toddler feeding chair

Professionals in the manufacture of children's furniture recommend using wood linden, beech, birch, but you can also take a pine. Separate details permissible to do from plywood. Small children, especially with the advent of teeth, love to try everything, nibble, so it is important to choose non-toxic finishing materials - varnishes, paints on an acrylic basis.

Materials, Tools for work

To make your own hands convenient, as well as a practical model of the table stand and chair for feeding, it is necessary to prepare:

Wooden timber with a cross section of 400x200 mm, the legs of the chair, tables, crossbars will be made of it. Choosing wood, note that there are no resin spots on it, bitch. Such defects greatly complicate the processing of details of future furniture.
A small board (about 250 mm thick), from which armrests will be made.
Sheet of fibreboard or plywood serves as a seat material.
Plywood for table top.
Drill.
Clamps.
Hacksaw.
Roulette, square, cirkul.
Pencil will help apply wood markings.
PVA glue.
Varnish or paint.
If you take the seat and the back soft, take the foam rubber, upholstered fabric, as well as a furniture stapler to securely secure.

Production workpiece, chair assembly

Use the tools to prepare the following details:

4 legs of stools with a length of 390 mm;
3 transverse stacks of a 300 mm length of 300 mm;
4 Rounded stool details;
1 Chair table top - 340x200 mm (size, form may vary as desired);
2 upper crossbars to a 220 mm chair;
2 lower crossbars to the chair 340 mm;
4 legs table standing with a length of 500 mm;
4 transverse tablets of the table of 340 mm;
4 planks - details of the table of 410 mm;
plywood from which the countertop will be made, its dimensions - 380x450 mm.

If the farm has boards or wooden trimming, they can replace some materials. You only need to give them a proper form, size.

The main thing is that you need to do after cutting parts, consistently, thoroughly pollnate wooden blanks with sandpaper. After grinding, all surfaces must be perfectly smooth, without irregularities, roughness, so that the child does not drive the zoom.
Relying on the attached drawing, transfer the marking of the rounded parts to the surface of the tree. At the same time, consider the part to come out durable, wood fibers must be located perpendicular to the corner of its fold. Using a joinery or just hacksaw cut these elements.
You can make your own shelter-waders 8x20x50 mm or purchase them in a special store. With the help of glue wrappers, the part of the chair, the table will be connected. Pre-neatly drill holes (approximately 30-40 mm). Also for reliable fastening parts can be used by self-draws.
We collect the sidewall of the chair (2 roundings, upper and lower crossbars, 2 legs). Sucks and holes by lubricate with glue, first the legs - we connect them. Then we do the lower crossbar and roundings. During operation, control the connections to be made at right angles. After the assembly, we are tightened and fix the elements with a clamp to complete drying (about 24 hours).
Similarly, we collect the second sidewall. Compare both results. Additionally process all parts by sandpaper.
We proceed to the manufacture and assembly of the seat and the back of the chair. Cut from FLN 6 parts 250x300. Moreover, the roundabout radius must be made of 50 mm (as in the scheme). Diligently grinding the place of details. We glue 3 details, put them under the press.
Ready back and seat connect to a selection of corner or screws. Also for this you can use a strip of a thickness of 80-100 mm thick. Bend it in the center and attach screws.
We collect a children's chair. We fasten the straps-crossing (300 mm) the sidewalls of the product. In the planks, on which we will clipped the seat, make 4 holes for the seasons. The plank under the back is also 4 (of them: in the ends - 2 pcs., In the bar - 2 pcs.) On the sidewalls, make holes: 2 - under the bar, which will keep the back, and 2 under the bar for installation of the table top.
Before the final assembly, you need to check the accuracy of the connections, then collect the entire design on the seals and glue. After a day, pick the chair again, remove the excess glue.
Cover the product with eco-friendly varnish or paint.

Assembling table

The assembly of the stand table passes on the same algorithm as stool:

We put markup, denoting the connection location.
We are preparing the wrens, drill hole drill.
Check the angles, the correctness of the connections.
We collect a fragment of the product, leave to dry the glue (we fasten the legs with the bottom and upper planks of 410 mm; cross-line 340 mm each attached sidewalls).
Install the tabletop.
We grind all parts of the product (even hard to reach).
Open lacquer or paint.

So that the stool transformer was more comfortable for the baby, the seat and the back is better made soft. Stick with furniture glue to these surfaces of foam rubber or several watin layers a little larger size (10-20 mm). Over wrap the seat and the back of the upholstery cloth or leatherette. Fix the stapler stretched material from the reverse side. It will be appropriate to install a lining (tissue or plywood) on the back of the back to eliminate the child's access to furniture brackets.

As you can see, make your own hands a wooden children's chair and a table is not a very difficult task. So you will provide your child with a convenient and safe place to make food, and subsequently - for educational games and drawing.