Make the table with your own hands. Table: Material, manufacturing technology, scheme, designs are simple and complex. Round table with their own trees

Even if the production of furniture is not your sphere, to make a cottage table with your own hands to gather with family and friends with warm summer evenings - a completely satisfied task.

The main advantage of its advantage is unlike purchased - undoubted savings. It is not necessary to make the table from scratch: just mounted purchased items, you will save 30-50% of the cost. If you manage to use the materials that remain from construction or repair, expenses will be limited to the acquisition of fittings.

To select the design, it is necessary to decide where the product will be used.

Using cheap non-consistent boards for a dacha or kitchen table - a non-thendition - you will get advantage of inaccessible for mass production. Sounds doubtful? But this is: bitch, because of which the boards are rejected, have the most interesting decorative properties. If you succeed successfully emphasize them - you will become the author of a completely unique designer product, which is sorry to leave in the garden in the rain.

Make a cottage table with your own hands to gather with family and friends with warm summer evenings - quite a satisfying task.

To choose a design, it is necessary to decide where the product will be used: on a grassy lawn under the tree, complement the gazebo, stand in the workshop or in the house.

The simplest summer cottage can be mounted in a few hours with a minimum of materials, but he will not last long. To get a product that will be really pleased to use, you need to carefully prepare boards and perform all the technical operations on each of the steps.

The main advantage of its advantage is unlike purchased - undoubted savings.

If you have found a big stump in the forest, it may turn out simple in the manufacture of a garden table. It is only required to remove the bark with the stump, make it up to the top smooth slice, pollute it, handle the antiseptic and cover with varnish. It is enough to kill or fasten to the "leg" made of stumps finished furniture shield - and ready.

Well watching countertops from the boards bonded at the bottom of the transverse rails. If you taste more to taste, it can be done with your own hands, but it will require great efforts.

If you succeed successfully emphasize them - you will become the author of a completely unique designer product, which is sorry to leave in the garden in the rain.

A beginner master is difficult to fasten the legs reliably, so try to choose a design, correctly appreciating your skills and taking into account labor and time. Most simple to make crushed and Mr.-shaped legs. To attach straight legs - you need to carefully connect the parts.

One of the most cozy options for the garden is a collapsible table with benches that can be installed in a gazebo or on a veranda. It is easy to fulfill it, the main thing to choose high-quality materials and properly prepare them for work.

The simplest summer cottage can be mounted in a few hours with a minimum of materials, but he will not last long.

How to choose a tree?

For the garden or kitchen table, the wood is suitable for the wood of many breeds, both soft (pine, spruce, cedar, fir) and solid (oak, birch, ash, nut, maple, apple trees, pears, acacia, etc.) Exception is too soft. Woods (poplar, alder, aspen, Iva).

One of the main parameters of the fitness of the wood for the manufacture of furniture is resistance to rotting: the above breed of this requirement corresponds.

If you do not plan to engage in furniture work constantly or just start practicing, prefer the most common tree breeds - pine and birch.

Well watching countertops from the boards bonded at the bottom of the transverse rails.

For tabletop, frame and legs, it is possible to use wood of different breeds. At the stage of assembly, you will need the seasons: they are usually made from acacia or says. Wood birch has a non-heightening pattern and can be significantly overcome due to the spilled fluid - it is better not to use it as a tabletop material, but due to the hardness of this breed from it you can make legs.

The countertop is best done from oak or pine. If you know how to brag the tree, the surface of the kitchen table can be a real work of art. The brash is amenable to wood of soft species: the tree is burned with a gas burner, and soft fibers are removed by iron brush. Work is better carried out in the yard due to a large amount of dust. If you managed to burn wood evenly, the result will delight you. Brash can be toned by verses, beans, diluted with artistic acrylic paint water. Of course, the brashing of the tree is not required: it is only a finish option.

If you taste more to taste, it can be done with your own hands, but it will require great efforts.

Selection of paints and glue

Before starting to install, the boards need to be protected from rotting. The tree must be impregnated with a water-polymer emulsion (VPE): processing is carried out twice with an interval of 3-5 days. This is enough so that the product last long.

Some models will need glue. Along with special carpentry adhesives (BF-2, etc.), it is possible to use a building PVA: it is applied on both bonded surfaces, dried to "lowlight", then connect the parts and kept under the press to three days.

A beginner master is difficult to fasten the legs reliably, so try to choose a design, correctly appreciating your skills and taking into account labor and time.

The choice of paints and varnishes is determined by the way it is planned to use the product: in the yard or indoors. For a garden table, which is inevitably exposed to precipitation, alkyd, alkyd-urethane, nitrocellulosic varnishes and oil paints are suitable. For the kitchen table, as well as for any furniture constantly located in the room, it is better to use acrylic paints and varnishes: they are more eco-friendly, they do not have a strong smell. Lucky marked with the "Blue Angel" sign recommended for children's furniture and toys.

If you decide to cover the wood by the veil, paint or simply tinted varnish, it needs to be made before assembly. It is necessary to take into account the compatibility of materials. The varnish is toned suitable according to the composition of the paint: if the lacquer is alkyd, the paint must be oil, if you use acrylic varnish - it can be toned only by acrylic paint. At first, a small amount of varnish is thoroughly mixed in a separate container with paint, and then the mixture is added to lacquer lacquer.

One of the most cozy options for the garden is a collapsible table with benches that can be installed in a gazebo or on a veranda.

What instruments are needed

For work you will need:

hacksaw,
circular saw or jigsaw;
drill;
screwdriver;
hammer (if it is decided to use nails).

For the garden or kitchen table, the wood is suitable for many breeds.

This list includes only the most necessary tools, but that the work is more comfortable, and the finished product looks aesthetic, it is advisable to buy or rent a rotary stouch, an eccentric grinder and a milling machine.

The swivel stubbob makes it possible to do Spike exactly at the desired angle. Eccentric grinder will make it possible to prepare the details simply, quickly and efficiently: you get excited the boards in an hour, instead of doing this whole day by hand emery paper. For high-quality processing of the ends, a ribbon grinder is useful, and the milling machine allows you to choose a tree for the necessary grooves and process the edges.

If you do not plan to engage in furniture work constantly or just start practicing.

Homemade pallets

The spectacular rustic style table can be constructed from pallets (wooden pallets). If you are a happy owner of such a container, especially a two-bedned pallet, - just disassemble it: there are no problems of acquiring boards!

Do you think that buy new boards is always better? You probably did not work with the tree before: it is impossible to use raw wood (a product is deformed after a few months), and dry boards are much more expensive. To dry the boards from raw wood, they are placed in stacks in a well-ventilated room: this necessary process will derete your project for 4-6 months! A good option for the kitchen table can be already mentioned discarded boards, too dry.

For tabletop, frame and legs, it is possible to use wood of different breeds.

Let's go back to the pallets: they are disassembled. Now at your disposal strong boards with different pattern and color, it is possible that from trees of different breeds. These features should not be considered as disadvantages: they will give the product a highlight: it is only necessary to create an interesting composition of them, alternating a similar shade board.

From the side parts of the pallet there is a great framework, and the remaining planks will be used to assemble the countertops.

Work is better carried out in the yard due to a large amount of dust.

To make legs, it will take a ram with a thickness of at least 5 cm. All items must be prepared: strictly for the fibers to sand sandpaper first large (NO120-150), then smaller grainability (NO400-600), carefully removing dust.

Some boards can be painted acrylic or oil paint. Loft style fans can use stenchers in the form of numbers or simple graphic symbols. Boards with a beautiful natural pattern "Morim" or just cover lacquer. After a filling or the first layer of acrylic varnish, soft fibers are risen; They need to be stupid by sandpaper of medium grain and apply a new layer of varnish.

The spectacular rustic style table can be constructed from pallets (wooden pallets).

If there is a varnish on a non-aqueous basis, it is enough to apply 2-3 layers, and if the acrylic - the number of layers can reach up to ten.

A good option for the kitchen table can be discarded boards, too dry.

Boards Countertops fasten the straps that are placed on the joints of the boards. With the help of a drill, a screwdriver and self-tapping screws, secure the boards to the planks (on the joints we use two screws, on one-piece boards - one). The use of drills is necessary that the wood does not cracked when screwing the screws. We collect a frame from the prepared sidewalls of the pallets. Using the drill, the diameter suitable for the diameters is drilled on the joints of the hole. Shakes with glue and fix the screws. We install legs: just screw the boards to the frame, screwing the screws diagonally. To reinforce the design, in a similar way, we do the bottom of the jumper.

To make legs, you will need a ram with a thickness of at least 5 cm.

Wooden table with glued table top

For glued countertops, you need to pick up the boards of the same width. If the table is intended for the workshop and its appearance does not matter much, you can use old floorboards: there are already grooves. To make the grooves yourself, the milling machine will be required.

For countertops, a flat surface is needed. Just wist the sidewalls glue, we connect the boards without gaps and we are tightened by the resulting design with clamps. Depending on the glue used, the countertop should dry from 1 to 3 days. If everything is done correctly, you will get a worktop with an absolutely smooth surface without cracks. The ends remains to be worked out - first pour a jigsaw, and then passionate. In the absence of tape grinders, it must be done by hand - sandpaper is first large, then medium grain.

After the varnishing parts, it is possible to move to the installation, which consists of several stages.

If there is no desire to mess with glue and clamps - you can use the finished furniture shield from the construction store. Then the worktop remains to be covered with a transparent or toned varnish.

For a good result, you need to apply 5-7 (for acrylic varnish to 10) layers. After each third layer, the working surface of the table tops must be stupid with fine-grained emery paper, carefully removing the dust with a wet cloth. At the stage of the varnish, it is important not to hurry: each layer of varnish must be good.

It remains to make the legs of a garden or kitchen table: Let us dwell on the variant with M-shaped legs. We need boards with a thickness of at least 22-25 mm.

For glued countertops, you need to pick up the boards of the same width.

Mr. legs consist of two parts connected at an angle of 90. On the connectable boards, it is necessary to make a sample, to wash the joint with a joinery glue, and then install the screws.

When the glue dries, cover the legs with varnish and after drying it is simply creating on the touch of the tabletop.

The connection of the legs with the worktop has several options.

Straight feet

To make straight legs, it is enough to drink a thick bar into pieces of the same length. The connection of such legs with a worktop has several options.

So that the straight legs have been installed securely, at home, you can use the connection on the sewage. They can be made independently of acacia wood or buy ready. For the assembly of the drain compounds, quick-drying carpentry glue (BF-2) is needed.

To make straight legs, it is enough to drink a thick bar into pieces of the same length.

Table with X-shaped legs

Sequence of work.

On the inner side of the tabletop, kpripim on a screw of two strips on each side.
In order for the table well, the edges of the slats need to pre-trim at an angle of 52.
Parry strips are fastened so that the legs fit, we make a 2-3 mm sweat on each side.
We put the boards on a flat surface, crossing them under the desired angle. We measure the distance between the ends of the boards: it must match the width of the table.
The place of intersection will result in chalk: here it is necessary to choose half the thickness of the boards so that after the assembly they lay in the same plane.
We embroider with glue and put the part under the press for 1-3 days. For greater reliability, the connection can be strengthened with self-draws.
Varnish legs.
It remains to attach them to the tabletop, having placed the grooves in the grooves formed by the slats - and the table for the cottage is ready.

X-shaped legs are made of bars or boards with a thickness of at least 50 mm.

Table with benches

The optimal solution for the gazebo is a dining table with benches attached to it. This design is better to make collapsible to remove for the winter room.

For the table, thick boards will be required (from 32 mm), which need to cut into pieces according to the drawing. In this embodiment, two benches are attached to the table. When all the details are cut, they must be seized, paying special attention to the ends. Each board is separately covered with varnish.

The optimal solution for the gazebo is a dining table with benches attached to it.

To connect parts of the structure, we prepare the stud (length 160 mm), nuts and washers - 24 pcs. For other connections, we use a screw or nails of a suitable length. With the help of a drill, it is necessary to prepare all the holes for fastening.

According to the drawing, we collect a countertop and upper parts of the benches. Transverse rails cut around the edges, the angle must be 45. It is convenient to do with a rotary stouch.

We make and fastened on the self-tapping screw all the legs. Breep spoiled at an angle of details.

Each board is separately covered with varnish.

We tighten the product with stiletts with bolts. Holes for the heels must be pre-drilled drill. By installing the hairpin, you need to wear washers on both sides and spin nuts using the key.

We tighten the product with stiletts with bolts.

Seat boards Fresh with gaps from 5 mm. When the seats are connected to the cutting supports, they are attached to the assembled boards 160 cm: you will need 4 boards.

We establish the remaining studs and enjoy the result.

With the help of a drill, it is necessary to prepare all the holes for fastening.

Video: Wooden table in a gazebo do it yourself

50 photo ideas: how to make a danish table with your own hands

If you dream nice to spend time on your household plot, then you just need a large table, followed by the company of your friends and loved ones. And you can make it you can do it, spending quite a bit of time. In some cases, you may need an assistant, sometimes an extra pair of hands does not hurt.

This article is a detailed step-by-step instruction managing a wooden table for giving.

Materials:

A - legs: bars 5 × 10 cm long 106 cm long (2 pcs.), 43 cm long (2 pcs.) And 56 cm long (2 pcs.);
B - frame: Bruks of 5 × 10 cm long 87 cm (2 pcs.);
C - Countertop: 5 × 15 cm boards 180 cm long (6 pcs.);
D - base-top base: 5 × 15 cm boards with a length of 87 cm (2 pcs.), Bruks of 5 × 10 cm 62 cm long (2 pcs.).

The first stage of the project is the manufacture of legs of the table. Screw the bars of the required sizes. To speed up the process, you can use the circular saw. Combine the edges of the bars and the line dug out the emery paper.

Connect the bars so that it turns out a X-shaped design, and secure them with 60 mm self-stakes, without forgetting to pre-drill the guide holes. Jump places to smear glue. Make sure that there are no cracks and gaps.

Make each pair of legs with horizontal bar, using 60 mm screws for this purpose. Ends of bars cut, as shown in the picture.

Put the boards designed for the manufacture of table tops, on a flat surface. We advise you to put a piece of 6 mm plywood between them, it will make it possible to form uniform gaps. Place the tabletops collected the sidewalls of the table and secure them by screwing them at an angle of 90 mm. Before fixing, make sure the perpendicularity of the legs and the countertops using the alcohol level for this.

Place a 5 × 15 cm of boards on the bottom side of the table top and fix them with 60 mm screws.

Screw the ends of the bars, which will perform the function of reinforcing the design of the backups, at an angle of 45º. Install the backups in their place and fix with the help of 90 mm screws screwed at an angle.

And finally, the last but no less important thing is: check if there are no screws of self-tapping screws over a wooden surface, and all the gaps and holes fill in a putty on the wood.

Tip: To protect the wooden surfaces from the destructive impact of atmospheric moisture, cover them with several layers of paint for outdoor use or simulation.

Table with benches. Instructions with drawings

Materials:

A - legs: Bars 5 × 10 cm long 95 cm (4 pcs.);
B - crossbars: bars 5 × 10 cm long 160 cm long (2 pcs.);
C - Mounting Countertops: Bars 5 × 10 cm Length 75 cm (5 pcs.);
D - inclined backups: Bars 5 × 10 cm long 84 cm (2 pcs.);
E - Countertop: 5 × 10 cm boards Length 180 cm (14 pcs.).

Start work stands with the manufacture of legs. Since this table feet will be located obliquely, the ends of the bars with a length of 100 cm should be cut off at an angle of 30º. Connect the elements of 90 mm bolts.

Make sure the surface on which you work is quite smooth. The mounted table sidewings should be identical, only in this case can be hoped for a great end result.

When the sidewalls of the table will be ready, you can start making a wooden countertop. We recommend that you put it on the ground (floor), and then fixing the legs with the help of screws.

Tip: Do not forget to make sure the vertical of the side walls of the table with an alcohol level, otherwise the final result of your work is hardly satisfied.

Rigidly fix the entire design using inclined backups. Their ends should be cut at an angle of 26º.

Now it remains only to build benches. Displays the boards of the desired size, place them on both sides of the table and, after drilling several guide holes at a distance of at least 1 cm from the edges, fasten with the help of screws.

Tip: In order for the seating boards to be distributed evenly, placing the carnations between them or pieces of plywood between them. Thanks to this little trick, all the gaps will be the same.

At the end of the work, pay attention to small but very important strokes. Fill the wood putty all the gaps and holes. After drying the putty, polish the wooden surfaces of the sandy paper of medium grain.

Tip: Do not forget to apply several layers of paint or veil to protect the wooden surfaces from exposure to water and sunlight.

Round table. We do in the country on your own

Materials:

A - base: 5 × 10 cm bar 102.5 cm long (1 pcs.) And 47 cm long (2 pcs.), Bruks 2.5 × 10 cm. 9 cm long (4 pcs.);
B - Racks: Bars 10 × 10 cm Length 60 cm (4 pcs.);
C - base-table base: Bruks of 5 × 10 cm long 82.5 cm long (1 pc.) And 52.5 cm long (2 pcs.), Bruks 2.5 × 10 cm Length 47.5 cm (4 pcs.) And 60 cm long (2 pcs.) ;
D - Countertop: 2.5 × 15 cm boards Long 195 cm (9 pcs.).

The first stage of the project is to create the base of the table. To articate the components of its elements, use waterproof glue and screws. Make sure the angles formed by the brushes connected, direct. To protect the collected base of the table from rotting under the influence of rainwater, place it on small stands from cropping 2.5 × 10 cm of the board.

Now you need to attach to the base four racks made from squares of square cross section. Before fixing, make sure that they are vertical using alcohol. The height of the legs may differ from the proposed by us, in this case you should, first of all, focus on your own needs.

The most difficult stage of the project is the manufacture of table tops. Place boards on a flat surface and check the center of the square. Secure at this point one end of 60 cm rail. Rotating the second end of the rail, mark the outline of the circle. Lobzik with a sharp blade will allow you to make a circular cut at a high professional level.

After cutting the boards of the future countertops, we recommend that you make them with a waterproof glue and additionally fix with several clamps. Attach the bars serving the base table top, as shown in the figure (yellow elements must be made of 5 × 10 cm of bars, green - from 2.5 × 10 cm of bars).

Tip: For attaching bars to the table top, use waterproof glue and galvanized screws (30 mm screws for mounting 2.5 × 10 cm of bars and 50 mm for fastening 5 × 10 cm of bars).

After the glue dries, you must attach the legs to the base with a feet with 90 mm of self-tapping screws, drill pre-guide holes. Control by alcohol level perpendicularity of legs and countertops.

In order for the result of your work to fit a high professional level, make sure that the hats of the screws are recessed deep enough. Look all the gaps and holes with a putty on a tree, after drying it to seet the surface with sandpaper.

Tip: Apply a few layers of paint for outdoor work or verses to protect the table from destruction under the influence of moisture. So that the bases of the base also turned out to be intact water, place the table on the concrete surface and their hermetically inlate them.

Now you know how to make a picnic table yourself. It is only worth putting a little effort, which will subsequently rewarded with enthusiastic exclamations of friends and pleasant summer evenings, held a family circle behind a large table.

The table is the second after the top item, for which a novice fastener should be taken. The design of the simple table is not more difficult than that of the stool; Unassuming comfortable table for the cottage or for a picnic can be built for half a day, using a hacksaw, hammer and drill. But a slightly refined table made on the same technology can also look at home and on the left in the figure., Instead, the expensive purchased. However, the table also gives greater freedom of creative expression, it can be a significant and even key element of interior design, no wonder the furniture makers are referred to as stoles, not skewers, cabinets or bedside sticks. I finish in the joinery craft, it will be possible to take the exclusive, other poses over time. Ibid.

This article discusses how to make tables from wood. Wood environmentally friendly, affordable and easily processed material with wonderful aesthetic advantages. In the products of utilitarian, it forgives newbies rather rough mistakes, but thin woodwork requires high mastery. Having learned to make wooden things, then master the glass, metal and plastic will be much simpler.

Tool and workshop

To make the table with your own hands, it is necessary for a separate production room from residential rooms: work on a tree, as you know, dusty. In addition, such good means of tinting and protecting wood, such as vertical, in the process of burning, distinguish harmful evaporation; Nitroleki, too, although to a lesser extent. Therefore, the home joinery must be well ventilated, and better - with forced ventilation. You can use the garage, but the sawdust will be much, and they will not go to the car. It is better to work in the Saraj; If it is not yet, it is possible to build, but on the farm he is much for what it is useful for what.

The usual carpentry tool, on the left in fig., For starters enough. But work will go much faster, and the result will be better if you attract modern achievements to the rescue, right there:

Rotary stub, pos. 1 allows accurately to the size and in the corner in 2 planes to do Spike. It is advisable to take it with a complete arctic saw, so everything will be cheaper together, and more accurate work. Stuslo - the device is universal, it is always useful and it is better to buy it.
Also universal manual electrolybiz with a tilted shoe, pos. 2, which allows you to guide the corner to the vertical plane.
Disk grinding, pos. 3 and 4, the newbie gives an opportunity for 5-15 minutes to get the surface of wooden plastic, to which the experienced joiner with a skin in his hand will take at least an hour, and tape, pos. 5, also quickly and efficiently process ends; There are still ribbon grinders for grooves and grooves with a protruding working body. These are already specialized tools for other works unsuitable, and quite expensive, so they first lease them first. True, the masters of the grinders still successfully brighted, i.e. Artificially stupid, tree, but this is a thin work.
It is also preferably at first to rent a manual wood milling mill, pos. 6, with a set of cutters. They process the shaped edges, choose the wells and grooves.

Very useful on the farm at all the universal household woodworking machine (UBDS) of different modifications. It is compact, placed on the table, food - 220 V 50/60 Hz 380-500 W. UDDS combines a circular saw, fugoval, turning on a tree machine tools and a set of incisors. True, the feet of the table on it simply so do not fall out, the departure of the rear grandmother caliper is small. But the caliper is just a steel round tube, lengthen it easy. Emphasis of the cutter remains regular, it is mobile, the leg and with a long caliper turns into one installation.

How to choose a tree?

Wooden table can be made from any wood of medium resistance to rotting, except the softer rocks: poplar, aspen, alder, willow, ailant. From domestic to such include:

The breeds are built in order of availability. For example, the billets of horse chestnut wood, plane and juniper are not underway at all: the first are too valuable for landscaping in the southern regions, and the juniper under threat of disappearance and is protected. Industrial billets of the Eblost almost completely go on shoe blocks, weaving shuttles, etc., and rowan - on weapons bed; There is no full-fledged plastic replacement. Stone birch grows very slowly, in limited places, it is badly renewed, so its workpieces are strictly adjustable, and the wood is expensive.

Note: Especially valuable for furniture Walnut - its wood combines high hardness with excellent viscosity, the most openwork carving for nuts does not ourselves. And the wood of nuts from caps - large growths on the trunk - the texture is not inferior to Karelian birch.

At the beginning of the joinery career, it is better to limit the pine, birch, oak, acacia and samshet. Pine or oak will go to the tablet; Birch - on the legs of the pine table; In the tabletop, it is strongly breached from the spilled one. Of the Acacia and the Samshat, excellent seasons are obtained, see below.

On a pine countertop from boards, you can even take incortive cheap boards - drove, swivel. But, of course, without dropping bumps, cracks, wormworts and traces of rot in the form of spots of unnatural color: black, gray, blue, green, in general, not like this tree. For example, traces of rotted on black (ebony) trees can be whitish or yellowish.

Why on a tabletop non-thendition? Perhaps also the unedged, which must be brought to the circular and Fuganke? And after the skillful processing, their wonderful beauty is obtained, on the left in fig. Manufacturers such a tree do not like: the production cycle is delayed, the waste is increasing. But for himself, it is not so scary relatively with the result.

Wooden Gorbushka.

Business pine has a clearly pronounced zonality of wood in the form of a year-old growth rings; Other conifers and many hardwood, it is also there. On the height of the board, the rings form the T. Naz. Gorbito in the form of fine concentric arcs. If the ripper of the tree is directed across the board of the board, as in fig. In the center, then when the shield is rafting for the countertops (see below), the boards are oriented with rippers alternately plumb, bottom in Fig. If the pumps are directed to the end of the board (right in fig.), Then the boards in the shield are put on the hubbles in one direction. These subtleties are necessary that the countertop will not be worked out during operation and did not break.

Varnishes, paints, impregnation, glue

Free wood protection tool from rotting is a waste motor oil, but for what they eat, this is not the best. The optimal will be 2 times, with a break of 3-5 days, impregnating the water-polymer emulsion (VPE), it will give protection for all the time of his life. Even birch plywood, impregnated by VPE, is suitable for facial furniture panels: covered on top also lacquer, it does not smell.

Old furniture nitrocellulose varnishes NC-218 and NTS-2144 with solvent No. 647 We gradually go out of use: they are superior to water-based acrylic varnishes in all parameters; In addition, they are safe. Also, the adhesives, bone joinery and BF-2 on alcohol are inferior to PVA; True, to obtain a high-quality seam, the latter requires applying glue on both surfaces, withstanding them to turning before the connection and excerpt under the yoke for 1-3 days, but it is acceptable in household production.

A tree for furniture can be toned in advance and protect the veil, which allows you to make beautiful setup items; An example will be given later. For tintors of the assembled nodes, you can use paints based on the same varnish and artistic (not painting!) Dyes: oil in tubes for lacquer and acrylic water for the same varnish.

First prepare "crucia": they take 30-50 ml of varnish and squeeze in it 1-1.5 cm paint with continuous thorough stirring with a picturesque brush. The core is stored in a tightly closed bubble and added to the varnish to the desired tone; The sample on it is made on a piece of wood, the tone is determined by full lacquer drying. Colored varnishes on HC and oil paints can be mixed according to the rules for mixing oil paints for painting; Acrylic - without restrictions.

The first steps

The country table is the first of homemade. If 1-2 pallets from the brick remained from construction, then the pallet table will be the first of the first. Not only because it is extremely simple, but also because it is very useful on the farm.

From one pallets, polished, impregnated and lacquered, it turns out a garden table like a journal, on the left in Fig. If there are steam in stock, of them, literally in half an hour, you can make a wall-mounted desk-rack, in the center and right. Chains for it can also be soiled from the soft wire, covered with PVC tube or, better, heat-shrinkable. For the full raising of the countertop, the small tool is placed on the shelf of wall pallets.

Having attached a little more work, from one pallets, a premise-collapsible cutting table for giving, allowing you to transfer the summer-autumn blank campaign to the street, not a merge of the husk and not trampled by numors. For winter, this table is going to a compact package. The design is clear from rice; Under the hatch in the countertop substitute a bucket.

The next in order of difficulty is the well-known country-goat table, in the crowd of a goat. Its design of 40-mm boards is shown on the left in fig., And in addition to it - a bench of the same device. And on the right - the country folding table on the same principle. It is hinged connections (M8-M12 bolts, washers and nuts with locknuts); In the place indicated by green, on nails put between the cross-stops of the Baschemas-emphasis countertops. In folded form, this table is placed in the car's trunk, so it will go to visit the picnic. If this is not foreseen, or the trunk is more, the countertop can be done longer.

Finally, it also does not require a special tool and skill table for the arbor, see fig. below. The material is the same board-forty and a little inexpensive fastener.

One step closer to art ...

To advance in the opposite, now you need to learn something from the Azov of carpentry skill. The table, in general, consists of a tabletop, its support frame, possibly with niches and / or mechanisms, or simply plates - a podstolye - legs, and bonding all the nodes together. Walk along them since the connections together with the legs, because Their mount is the weakest table place.

Connections and legs

At first, we need to master the connection on the wanks - round wooden bugs, see fig. Skanovy compounds are assembled on quick-drying M adept adhesive: joiner, BF-2, acrylic. Sometimes for connecting thin boards, instead of the waders use nails with hatched caps, pos. 4, but it is bad: the tree dries, and the metal is not, and over time the connection is cleared.

The seeds take a small-layer tree stronger than both connected parts, i.e. Hardwood. A table made of pine on birch legs can be connected on oak or beech ducks. There are ready-made round wands for cutting ducts; Before applying from the edges of the Speeds, chamfer is removed. Plastic waders are sold, but they are intended exclusively for detachable compounds, for example. Inserts in sliding tables.

The legs to the tables of industrial production are attached with detachable kings, see fig. on right. Pos., Marked yellow - the simplest, cheap and bad. With its disadvantages with the complete absence of advantages, buyers of the ShirropTrebkovskaya Soviet furniture are well acquainted, let it remain there. Reliable, well kept, except for the legs, and the boards of the podstoly, the kings with mortise drives, "green" pos. They also require the least costs, but rather laborious, so in the industry they are rarely applied, but an amateur just right. The king with the shaped steel dust, on the right above in fig., Even stronger; In this way, it is possible to mount the legs with a round headband and any, however, it requires purchased shaped parts made of high-quality steel.

Note: The legs to the round table are attached, as shown below in Fig.

The removable legs are needed not only for the convenience of storage and transportation. In a small-sized apartment with a narrow corridor, the table with legs is often simply impossible to stay to the living room as it is neither verth. Modern apartments are spacious, and in 1-storey private houses, the table can be submitted / out the window, so in such cases it turns out the strength and durability of the table with tightly fixed legs.

For tables on the rectangular base, the legguards of the legs under the deaf mount should also be rectangular, pos. 1 in fig. By the way, the tsargi are also inconphigible: then the legs with the wrenches that pass through the mortise wooden bay. From the inside, the wanks are cut into the flush and are crushed with cousin or samshety wedges, inserted across the fibers of wood bodies. Assessed with glue, such a compound is so firmly and durable that these tables of 200-year old can be fighting, grasping the leg.

Sweet-quality tables on the accurate legs are collected simply on the wanks, pos. 2. For tables, the legs are easier made from a bar and fasten with self-assembly after attaching the countertops to the substield, pos. 3. Ever easier and easier legs from a pair of boards each, pos. 4 and 5. So that they do not cling to the floor, on them below you need to fill the ribs or put the table on the wheels.

Table top

It is easier, but not cheaper than just, order a tabletop from laminated wood chipboard (LDSP, laminate). LDSP for countertops is available in the form of T. Naz. Post-Forming - 2,6x1.2 m plates with a thickness of 20-60 mm with a decorative coating. The top edge of the post-Rhinestone is rounded, lower ray with a kippler, see fig. Modern furniture laminate is quite environmentally friendly, whatever you wanted to forget the Sobmebell, from which the months stuck with phenol.

Postforming well buy small furniture enterprises. They always have its waste; Of these, you will be happy and for quite an affordable price will cut out a countertop in size if there is a coordinate-cutting machine in the enterprise. Perhaps such an order will receive an IP-loner if sits without a case. The finished plate and climb, i.e. Pvc Cat (edge) will be covered. If you raise yourself independently (an uncomfortable approach is sometimes requested for the edge), then consider:

The upper and lower shelves of Kant have a different profile, see on the left in Fig. Convert - on the table there will always be a cattle of dirt.
Kant need to take exactly the stove thickness. Singing a 24 mm Cant for a 25 mm slab can be, but it slides soon.
The grooves must be selected for the Cant comb, you need to choose a manual disk cutter; The saw seems to have no one else.
Before installing the Kant, a thin layer of silicone sealant and a "sausage" is applied to the surface of the end and the "sausage" is squeezed into the groove; In this case, silicone will be lubricant, without which the Cant Comb can simply see.
The comb is introduced into the groove with light blows of the Cyan, gradually moving along the contour. The countertop should at the same time lie on the support face up; The extruded surplus of silicone immediately erase with a clean rag, slightly moistened with table vinegar.

Boiled countertops are splitting in the boardroom with wedges and spacers - Vaimima. Viima is quite possible to make himself; The countertop needs 3-4. Boards (cheeks) Waim wrapped with polyethylene, so that the shield is not glued to them. In fig. For example, the process of manufacturing round countertops; Rectangular shames the same, only trimming in size is easier. The shield on the worktop on the adhesive and the wanks (see below) is paid; If the boards are tapped, the wrenches are not needed. When rafting on the PVA, the next defense before installing in the wiim is kept up to the rotation of the applied glue.

Often, countertops are collected without livea on the plaza - a flat surface, covered with polyethylene film. To collect on the plaza, a good boardless shield will not work: or he will come to a slit, or when assembling a board, stand on end. But typical countertops from fragments are obtained in skillful hands are simply wonderful. For example, on pos. 1-3 rice. - Countertop from sawing waste toned by the verse. And on pos. 4-5 The basis of the countertop was the plasma and plywood itself. The tile and its fight are glued with tiled glue, then the depressions are filled with grouting for peat, the surface is labeled and the contour is circled with the edge of a wooden rail.

Note: These examples illustrate not all the possibilities of manufacturing typical art countertops with their own hands.

Podstole

Podstole table with non-removable legs - simple wooden frame, left in fig. Niche and details of mechanisms in the power scheme are not involved. If the table is longer than 1.2 m, or the countertop is removable / sliding, or large operational loads are assumed (for example, the working table), the substole is strengthened with rigidity ribs, in the center. If the legs are attached to the kings, then the podstole is performed at the same time with the worktop, so that a single power scheme is turned out to right in Fig.

Without Rama

There are also tables without podstoles, in which the tabletop with legs work in a single carrier system. Very durable, for example. plywood table on the left in rice; Connections His dunning. Unfortunately, this design for an amateur is not economical: the sidewalls cannot be assembled from pieces, they must be solid. In mass production, the deposit is not very large, but a sheet of plywood with a thickness of 24 mm will go unstuckly into large sidewalls, and 1 more to smaller. The table, which on the right, is already quite possible to make with your own hands: the carrier frame of the team; Connections - in spike with a suspended bolt and hardwood. However, the table top in this case should be round or square, with rounded or straight corners.

... and get into the kitchen

Exactly. The table for the kitchen is next in order of difficulty after the simplest country. It must already comply with the requirements of apartment ergonomics, sizes - 75 cm in height for people of medium completeness; The width of a 1 consumer / seed seat 60-80 cm depending on its case, the tabletop width is at least 70 cm. The aesthetic appearance is very desirable, but it is not determining: suddenly you have frowning with decoration, on the tablecloth. The countertop should be easily washed, durable, resistant to spilled heating from hot dishes.

All these requirements will satisfy the table from LDSP on metal legs; They also have separately on sale kits for 4 pcs, with fasteners, left in fig. Factory legs for tables, as a rule, are supplied with heels adjustable in height. The table, the manufacture of which will be reduced to the screws with the screws-confirm nests of the legs, will cost 30-50% cheaper than the purchase entirely, and it does not yield to him, right in fig.

If it's not too lazy to apply, steel legs can be done with your own hands. This is not only a cheaper, but also more durable: the nests of the branded legs cast from a rather fragile silumin, fastening weaken over time, they need to tighten. You can cut the nests from good steel, and the keen feet in them.

In the kitchen, there is a reasonable, perhaps there is a place for the table more. At such a case - on the trail. Fig. Drawings of the kitchen table in rustic style. "Rusty" this table is not only by appearance: it does not have a single nail and generally metallic fasteners. Only tree and glue. The connoisseur, seeing such a well-approvingly coming head, and the design is simple and is available beginner. True, in addition to the countertops, you will have to allocate and shields on the sidewalls, but in this case it is worth it.

Krugli

The table with a round tabletop is appropriate in any room if it is placed there. But the countertop from the boards in this case is not the best option: due to the presence of sharp corners, it is without frame, very complex and time-consuming is exposed to splitting. From this shortcoming, set-up tabletops made of small fragments, like the waste described above; In contrast to the laminate, they are decorative, stylish, unique and practically free.

The sharp corners in the fine-type countertop are even more, but then the "law of a broom" is triggered. Not the American Senator of a broom, who loves democracy in Russia until a complete oblivion about it at home, but of that broom, whom Sor Mat. As you know, to break it (broom, not a senator) is impossible connected, and a twist break for a twist and a child. So, due to the ease of the distribution of loads between small fragments, the tabletop set works as a solid stove, and it is possible to cut it after the assembly at least the "letter ZY".

Note: for the idea of \u200b\u200bSenator-broom, sorry, broom, brought out the statement of his compatriot Samuel Clemens, world famous as Mark Twain: "I argue, and take it to prove it that Mr. Cooper Fantasy is no more than the bull. But not that bull that might on the pasture, but what is the support of the bridge. "

How to make a semi-fold round table, shown in rice; On the right there sizes of countertops and the order of assembly. And in fig. On the right above - a small round table for an entrance hall, according to an old classification - a visit. Its feature is the minimum number of compounds; Assembling on glue. Any killesh will go to the tabletop, from spike stumps to the cardboard, made according to the method of making cardboard shelves, but the substole is necessarily durable, of wood (board-two-year) or LDSP.

Go further: in the living room

The table in the main room of the house should be to the face of the whole house. At the same time, with a modern desire for the latent design of the design (which also saves the cost of living space) the table must not reach the eye and take a smaller place. Therefore, one of the most sought-after objects of the furniture of our days was a transformer table.

The simplest transformable table, which, with all its transformations, remains a table, and does not turn into a closet or bed - table table; It is quite possible to make with his own hands "from scratch". There are 2 options are mostly used here. Left in fig. - The table is deployed, he has a record attitude of the occupied area in the deployed and folded form. Such most often put in apartments studios perpendicular to the wall on the border of the kitchen and living area. With the feces of countertops, he will serve as a bar. Raising wings one by one, you can get a kitchenette or everyday dining table, and completely unfolded (in the center), it will provide a place for a rather crowded banquet.

The bedside table living in a small-sized apartment is suitable, the folding table table, on the right in fig. This, in essence, 2 small round folding tables described above, connected by a rectangular insert. You can dine alone with it, because, unlike the previous version, there is where to go foot. And pulling out, spend a romantic evening with an excellent stranger or spiritual gatherings with buddies.

All of the above qualities combine journal-dining tables-transformers with a mechanism. The variety of transformation mechanisms is large, but for tables that are always tables, they are mostly reduced to the 2nd types: elevator (pantograph) and book. As the other, see the video:

Theoretically book is stable elevator, although there is a lot depends on the quality of execution. Fans of books are popular, because the mechanism of the book can still be made independently, and the elevator outside the production conditions is unlikely.

As the table is unfolded, it is shown in stages in fig. on right. For its independent manufacture, you need to know that the key node is a damping-balancing elastic link. In fairly expensive corporate structures, very softly operating gas dampers (gas lifts) are used, but the lover is better to stay on the spring damper, and not because the gas lift is much more expensive.

The fact is that the gas lift should be in fair narrow limits agreed with the kinematics of the lever system, the weight of the countertops, the podstolia and the own weight of the levers. If the balance of the entire system does not fit into its characteristics, the mechanism simply will not work. And the spring can always be tightened / weakened; As a last resort, replace. In general, the unsuccessful homemade transformer table with gas lifts rarely manages to "bring to mind", and the spring is almost always. If you decide still to suffer with a self-made acrobat table, in fig. - Drawings of the spring transformation mechanism.

Without the presence of drilling, turning and milling metal machines or access to them, most of the details of the transformation mechanism will have to be ordered. Then its manufacture will cost a little about $ 40, and it is possible to buy a good ready for $ 50- $ 60. The factory, the same coffee table-transformer rarely, when it pulls less than $ 200, so that in this situation savings exits significant.

The transformer table is done under the mechanism. Some of the most popular are Mazetti transformation mechanisms, thanks to good quality with a reasonable price for this class. In addition, Mazetti mechanisms are available in the carrier frame (insertion in the center in Fig.), Which makes it much easier to install. Other pos. In fig. Show the device and sizes of the table under this mechanism.

For strong Pirushka

What do not say, but in a normal family with children, friends and relatives without crowded gathering at the table does not cost, and then the transformer table will not always help. However, banquet tables for the living room in a more or less complete volume will be left, as they say, for later: these are products of higher complexity; First of all, due to the mechanism of splen.

By the way, the old good "slippers" with wooden guides and the wooden slides of half the table tops (pos. 1 in fig. Modern mechanisms of spleen with telescopic finishing guides, pos. 2, it allows you to apply not 1, and up to 3-5 inserts, which increases the table capacity by 6-10 people, respectively, but quite the road, and their installation requires a description of no less volumetric.

There are banquet tables with clamshell inserts, pos. 3. In elite models, the insertion / sliding / shift, the inserts raises, lay out and puts it into place or removes a very complex mechanism back into the substole, but its manual options are available for making at home.

As for banquet tables with drawn individual tables, arranged like a stand under the keyboard in a computer table, they cannot be called popular: filed forward (and how to avoid it, if the house without servants?), We get the board back in the prestole, and your portion of treats - on festive clothes.

But we will not be about sad. Recall that the table is far from always, and you can use the attachment, the one-piece table in any case is more reliable. Therefore, on a series of drawings below - the way to make a very durable and inexpensive dining table, and how it looks like "live" - \u200b\u200bsee on the left in Fig. at the beginning.

In addition

The table, and any furniture, often want to paint not just to the stripes or artistically paint. To protect the drawing from external influences and ensure the possibility of replacing the varnish if necessary, paint should not be applied, but to rub into a tree to varnishing. The painting technique in the way of layer-by-layer rubber paints is called a lesser. So in conclusion, we offer a master class on wood lesing.

Video: Master class on wood lesing

Of course, today everyone has the opportunity to buy in the store any furniture, including the table. But why not make it yourself, do it yourself?

It is not as difficult as it may seem at first glance. In addition, you have the opportunity to make a table that will be perfectly approached in size and appearance to the interior of your kitchen or other room.

In addition, furniture made with your own hands is not only saving money, but also by any, but a reason for pride, since in our days there is nothing to cray.

What are the tables

If you decide from the boards with your own hands, then you need to figure out what kinds of tables are, and it is necessary to decide what you need.

The easiest is a regular table with four legs, a table top and frame. Make it will not be difficult even to someone who is not tempted in woodworking.

If you are experienced enough in this matter, you can make a dining table round or oval, decorate it with a thread, painting or burn on the surface of the drawing and patterns.

A more complex option is from the boards. In fact, it is the same common table, but quite thick and long crossbars are attached to its legs, on which the seatboards are laid on top. So we get the table, from two sides of which there are benches. Such furniture is good for both the kitchen and installation in the courtyard of a private house or cottage.

If there is free space in the room only in the corner - make an angular table that perfectly fit into this unoccupied space. Let him not so comfortably dine like a classic table, but you can put a TV, a microwave or kettle - there will be enough space there.

Another interesting option can be a windowsill table.

In fact, it is the same window sill, but significantly advanced and fitted, for example, under a convenient workplace for a schoolboy.

The advantage of such a solution is that the table will be well covered most of the day.

The minus is also there: sitting in winter at the same table, the legs will have to rest in a very warm, even a hot heating battery, which is not very convenient.

Materials and tools

To buy everything that you need for the manufacture of the table with your own hands, it is quite simple and will not be much labor, no extent. The main material for the dining table is a tree, or rather:

Boards Thick from 25 to 50 millimeters, 100-150 millimeters wide, long enough.
The thicker it is the material for the countertop, frame and legs, the harder, but at the same time they will be more durable.
Choose boards from a good tree, without any defects.
Bar. It is necessary for the manufacture of the legs of the table, because choose sufficient thick and strong samples. The bar can be replaced by the same boards, if they arrange their letter "g", or use the purchased aluminum feet of the table. Also as legs can be used balusters (figured carved columns made of wood that support the railing on some stairs).
Chipboard or plywood sheets Which can be used as materials for countertops. Choose sufficient thick and strong samples that will withstand daily loads.

As with the materials, andluggage and fasteners for your own hands get just, they are in most homes. If something is missing - you can buy in the nearest construction store.

pencil, corner roulette and ruler;
electropolitanzik or hacksaw on wood;
screwdriver with a set of nozzles and drills;
plane, If you need to pre-process boards from irregularities and defects;
set self-self-screws, Furniture bolt and nuts;
emery paper or sander;
varnish or veil, roller or brush For processing the finished table.

Attention! Working with an electrolybik, always remember the rules of security and do not allow you to have a number of small children or domestic animals!

Simple kitchen table from boards

To begin with, we need to make a worktop.
There are several options here:

Cut out of the chipboard or plywood sheet, the size of the scene with the jigsaw;
Lay a few fairly wide boards and subsequently consolidate them on the frame;
Take a large number of relatively narrow boards, arrange their side up and glue with a joinery glue.
As a result, it turns out quite thick, heavy and durable countertop.

Stages of work

Step 1. Collect from the board countertop.

Step 2. We manufacture frame from boards or their wooden bars. In size, it can be made equal to a tabletop or with a small indent, about 2-2.5 centimeters on each side of the table. Circling part of the frame with screws, connect the same frame with the worktop.

Step 3. After us fromodineli together frame and countertop, half the table is ready. It remains to make only his legs. If a bar is used for this, drill two holes in it under furniture bolts. Moreover, they can be made both on the one hand, one over the other, and from two different for more reliable fixing on the frame.

Important! Carefully check the length of the table legs, they should not differ among themselves. Otherwise, the table will stand uneven and stagger. If you do not want it to do not spoil the floor material - secure rubber "shoes" in the lower legs.

After you make similar holes in the table frame and secure the legs and the frame with bolts and nuts. Also, the legs can be fixed from above, with the help of screws, but over time this fastener can relax.

If you want to make the legs of the table from the boards, fold two boards in the letter "g" on the outer or inner corner of the frame and secure them with the help of all the same furniture bolts or screws.

So that the legs are not loosened, connect the folded boards with each other in the lower and middle part with the help of screws or nails.

That's all, simple and reliable, made with your own hands, ready!

Tip: Before proceeding to, make the simplest drawing, preferably from several sides. Constantly check the dimensions of the parts. Some details of the same size can be pitched simultaneously if you fasten the boards or a bar with clamps.

Table of pallet

Wooden pallets are widely used in stores and warehouses as pallets for cargo.

If desired, you can get free of charge a few pieces and use as a basis for the manufacture of an original and unusual kitchen table.

If at least one side the surface is solid, then the worktop to make you no longer needed, it is ready.

You only need to process it and, if you want to round the corners.

Note! Since initially pallets are designed for warehouses, no one is engaged in grinding and cleaning. Therefore, before pinning the table from them, carefully polish them and remove all burrs. Rights and boards defects can be hidden using a putty.

Stages of work

Step 1. Most pallets are open, and there is quite large between the boards. distance, because of which to use the surface of pallets as tabletop Not too comfortable. You can solve this problem in two ways: either to make boards The corresponding size I. consolidate their screws between the pallet boards, or install top plywood or chipboard.

Step 2. Like for ordinary tables, feet for tables from pallet can be made from bruus or boards. The best thing fasten them with quite thick and strong Pallet bar with nails, sculpov or furniture bolts.

So that the legs are not loosened - connect them between themselves crossbars.

Who said that the table is a simple subject of the interior? In fact, the creation of a table is a fascinating occupation, especially their own hands from a natural tree. Today in the review of our editorial office we will tell you how to make a table of wood, what knowledge you need to have the design to serve for many years without complaints.

Ideas for manufacture with your hands Table table: photo, recommendations, drawings and step-by-step instructions

Before working, it is important to determine the following moments:

Sizes and operating conditions. From this will depend on the functionality and additional activities that will need to be taken.
Find (draw) plan scheme.
Selection of material and accessories.

For a novice wizard, choose better sketches easier. Here are some sketches that you can come in handy.

Article on the topic:

Photo examples, drawings, schemes, materials; Features of manufacturing furniture for the garden, children's, bath, gazebos, tips and recommendations of masters - read in our publication.

Wooden table for cottages and houses: material selection

It is best to use a natural tree. Even old boards will be suitable for an experienced wizard. Several movements of the plane and here - the raw materials are ready for work. Prepared wood need to dry.

Tools needed to create a wooden table with your own hands

For the manufacture, for example, you will need a minimum set of hand tools: hacksaw, hammer, stub, screwdriver, nails, screws, roulette or ruler, kitchen and pencil.

Article on the topic:

: what it is, advantages and disadvantages; Step-by-step making coffee table, armchairs, sofas, shops, rack; Features of the decor with photos - read the publication.

Table of wood with your own hands: drawings, photos and step-by-step instructions

For work you can use both whole boards and. Spend a revision of old furniture, it is possible that you will find materials that can be used.

Making a round wooden table

Let's consider the process of making a simple round table from the cottage boards. We will need conventional boards and rails to secure the design.

Important! Before starting work, the board must be treated with a planer and emery paper.

Illustration	Description of action
	Processed boards lay out in the sequence in which we will shoot down the table. In our case, they have grooves and connect them along the spike-groove system.
	Connect the boards with the help and squeeze the clamps. After 24 hours, the clamps can be removed.
	With the help of bars, we increase the tabletop. Further, on the obtained shield, find the center and, with the help of a circulation or auxiliary means (nail, twine and pencil), outline the circle with a diameter of 1000 mm.
	Next, with help, cut out the circle in the outlined circuit.
	Grind the working surface.
	We will make legs from bars with a size of 4 × 4 cm. Processing them with grinding.
	Foots fix on corners.
	Here is such a simple table for the cottage we turned out.

Article on the topic:

: photos of the stages of work, the advantages and disadvantages of these beds, their types, as well as a step-by-step master class on the manufacture of such structures, how to properly choose the mattress for beds from the pallets - in our publication.

How to make a wooden kitchen table

A very simple and stylish table can be obtained by spending literally one evening in.

By the way, this model is very popular if you want to be the same in the kitchen, you can make it with your own hands.

And here is another option to manufacture a simple kitchen table with your own hands -

Photo gallery of various options for wooden tables made with your own hands

For example, we propose to study several versions of wood tables for different premises in our photo gallery.

1 of 8.