Cutting at an angle of 45 degrees. How to flicker angle dried tiles

Saving involves driving and grinding cutting tiles 45 degrees. Docking of roasted under 45 degrees of the date is a beautiful visual effect and come in handy for the design of niches and other outer corners. Without driving and other decorative corners, the tile is often put when one side rests on the edge of another tile. In this case, one of the tiles ends is exhibited. Such compounds can very often be seen in hospitals, schools and other public places.

When two tiles are joined under the corners of 45 degrees, then such an outer angle looks much more cute. Ideally, instead of junction of tiles, you can achieve without suture convergence. There is a simpler when docking tiles roaming, leave a small gap for the sealing of the fugue. You can see in more detail in the learning video lesson "Cutting tiles of 45 degrees".

Finishing the styling of the second row of tiles, approach niche where heating battery is located. At the beginning, we will need to be placed and cut the tile, and then make a snap. To do this, apply the tile and install remote crossings and pre-celebrate the place where the edge will pass. At the place of the future cut is tightly incite. It helps protect our tile from chips. It is possible to apply another type of trimming tiles with stoveturis. In this embodiment, we will cut and cut the tile using the usual grinder.

Circumcision tiles Bulgarian

For circumcision with the subsequent burrow, we need a little Bulgarian. It is worth paying to the disk that will need to be installed. This disc will be on stone and concrete and it has notches on the cutting part. There is also a disc with a solid cutting part and there are no notches on it. It is designed to cut stone and tiles when cooling with water. This disc is not suitable for cutting the tile with a grinder, but it is possible to try to take a snap. In many respects it will depend on the quality of the manufacture of these disks. Do not be lazy to see options in the construction store. It is also worth noting that you need to use safety glasses and gloves when working with a grinder.

At the beginning, we should trim the tiles along the drawn line. It is worth producing this operation, it is worth abide by caution, so as not to go beyond the line. This cut is performed at the right tile angle and removing the excess part, slightly under the grinding edge. Now this edge can be burned, that is, sting at an angle of 45 degrees. Of course, a certain skill is required to fulfill this work, but it is easily trained and here are the main features.

Bulgarian disc is all the time under the corners of 45 degrees to the tile. Moving disk on the tile, remove a small part of the edge. Movement up and down should be performed smoothly. Try not to hurt the glazed edge of the tile and leave about 1 millimeter to it. So you can avoid not the necessary chips.

When the coarse burner is performed, it is possible to remove the scotch. We look at the edge of the tile and see that he is nothed in an angle of 45 degrees. Now we will bring this room to the perfect state with the help of the skin. The skirt is laid on a not big bar, which is placed on hand.

Grinding tile

Now the final grinding is performed by the edge. The bar allows you to monitor the corner of grinding, it should also be at an angle of 45 degrees. Movement should be light, visually all the time control the reverse glazed edge and try not to touch it.

Having finished grinding and check the quality of the work of the skid. If you need to carry out once again grinding. As far as high quality driving, you can check when you docile two tiles. The resulting joints will immediately see the error. They should be eliminated, especially if you plan to stick the tiles without suture.

In our video, the lesson was used by a simple tile trailer external with the use of seam. The seam on the angular junction of two tiles is selected by the size of a remote cross, which is used for this wall tile.

Conclusion

Sometimes the slaughtering tile under 45 degrees is a good option for its docking with window opening. Such a junction will look very beautiful. In conclusion, it is worth noting that the alternative to manual snacks with the help of a grinder is the use of a moche cutting machine with adjustable tile position.

With the help of CIFRE CERAMICA tiles, you get a constant design in the bathroom. Buying CIRFE tile in the online store will be able to choose the option you need, using an online consultant to learn what kind of design the best is suitable in accordance with the room. Ceramic CIFRE CERAMICA tile is a great style that never comes out of fashion.

Check out other video tile laying with your own hands on our website. We hope you were able to apply the knowledge gained and you got a cutting tile 45 degrees.

The greatest difficulty in laying the tile should be called the finishing of the inner corners, as well as external. Especially if it is necessary to produce washed under 45 degrees. In this case, the main thing is to choose the specific version of its execution, as well as take into account possible errors.

Using grinders

Few people know about how to make an angle with tiles qualitatively and in fairly short time, with the least financial costs. The most successful option for creating an angle on a tile of 45 degrees is the use of an angular grinding machine that is equipped with a diamond disk. The disk is intended for performing precisely dry cutting. Working with such tools should be carefully and with caution so that the subsequent in the corners has passed successfully.

If there is no skill of creation, it was driving under 45 degrees, it is best to pre-train, that is, to take unnecessary elements of the tile and experiment on it. Cutting tiles at an angle - a very time-consuming process that requires skills and skills. Test options will allow more accurate and efficiently to produce work, that is, to trap the hand to a pretty.

Stages of work

Work is performed in several stages:

At first, the tile is installed on the edge, so that the cutting angle is located perpendicular to the surface.
The angle of ceramic tiles during the formation is chosen in 45 degrees. At the same time, work is made precisely with the back side of the tile - melted.
If irregularities appear, you can try to hide them with the same grinding machine. As a tool for grinding, an ordinary Bulgarian can be used to which a special disk is attached, with the possibility of fixing the grinding skin of the round shape of the corresponding rudeness (circles on velcro, which are easily replaced with new ones).

When the tile cutting under the angle of 45 degrees is properly performed, it will happen thin and almost without the formation of a slot. But even in this case, it will be extremely invisible. All noticeable places, jokes of tiles on the corners, will be decorated in the best time.

To work there can be a completely any tile, any modification. The main thing is to maintain all the qualities and properties of the upper decorative layer, glaze. Avoid damage will allow not in the proximity to such a surface. Sufficient will withstand the distance of 2 mm.

In the presence of uneven irregularities at the corner at docking, you can use it, designed for seams. With it, all defects and errors are hidden. Tile seams in the corners will be practically not noticeable.

If there are doubts how to spend the tiles under 45 degrees, it is best to seek help from specialists who have a certain experience.

Working with a grinder When the device washed under 45, it is simply performed, but the disk selection is required. Not excess will be consulted with a specialist. The main disadvantage is that a large amount of dust is formed. It will not be superfluous to the room where it will be less influential, such as a balcony.

Platecores

Here we are talking about professionals that are involved in similar works on an ongoing basis. Two models of FEIDA are the greatest popularity:

FEIDA TC 200;
Feida TC 250.

Despite the fact that this is the production of Chinese companies, they have high quality and accuracy of cutting.

With their help, a completely any angle of the tile is performed, which will be necessary for. Most often it is 45 degrees and is popular.

Also among firms with reliability, Einhell is distinguished and proton.

Many problems here arise when working with a wavy cafeter, when the plastic circuit touches the glaze. It becomes scherbat and "torn", which will noticeably spoil the appearance. Working with tiles will usually be performed by professionals. After all, no one will acquire expensive equipment for personal use. Such is extremely rarely conducted:

with the device of external angles;
when entering a particular room.

When ordering services from a construction company, it is best to preliminarily clarify its status and experience in this direction. Not rare cases when "destroyed" a large amount of tiles. Each nuance should be prescribed in advance in the contract, so that there are no problems in the future.

Quality from execution washed under 45 degrees using professional noticeably immediately and everyone. In addition, work is carried out in a short time, which allows you to start harding the tile almost immediately. This design of the corners of the tile will soul to each owner of the room in which the tile will be glued.

Using sandpaper

This material most often has to help to hide the inaccuracies of the preliminary when the glaze is damaged or the chips remained. In addition, there is another embodiment of sandpaper.

Instead of a professional tool and the need to preserve the glaze layer, an incision is made on the front part with the help of glass cutter. After that, on the reverse side, the grinder was made in the form of the letter "V", which should be performed across the entire width of the tile. It remains only to break the element, and the remaining work is completed using emery paper.

Some craftsmen are trying to reduce work costs using only ordinary emery paper. In this case, the angles of tiles under 45 degrees are made independently, following the condition of clay and the glaze itself. If you overdo it, the damage touches the tiles, therefore, you will have to spend money on the purchase of similar material. The rudeness of the sandbach itself will be essential, which should vary.

For accurate alignment, two variants of the material for creating a bevel under 45 degrees are suitable:

№40 and №60.
№40 and №80.

The first numbers will be used as a rough adjusting of the tile, and the second to create a really smooth and high-quality surface as high quality. Only after that you can put a tile at an angle, not afraid, criticism from the side. When complying with the requirements and recommendations from specialists when performing marbles under 45 degrees, there will be no questions about how to arrange the tile angles. As a result, you can even say that the tile without corners turned out.

For greater clarity, you should see thematic videos, the selection of which we did a little below.

Now I will tell you how to make a manual skating tile. Saving involves driving and grinding the tile under 45 degrees. The docking of the tile washed under 45 degrees gives a beautiful visual effect and is useful for the design of niches and other outer corners.

Without driving and decorative outer corners, tiles are often joined in such a way that the edge of one tile rests on the edge of another. In this case, the end of one of the tiles is exhibited on our review.

This can often be seen in hospitals, schools and other public institutions.

When the tiles are joined, dried at an angle of 45 degrees, then such an outer angle looks much more cute.

Ideally, a seamless converge can be achieved at the junction of the tiles. There is a simpler option - leave a small gap between the tiles for the sealing of the fugue.

Now I will show how it is done in practice.

Measuring and trimming tiles

Finishing the second series of wall tiles, I come to a niche, in which the heating battery is located. And here I have to first place and trim the tile, and then take a snack.

I lay the tile and install remote crossings, pre-marking the place where the edge will pass. I tightly stick to the future cut to protect the future tile from chips.

Of course, there is an option first trim the tile on the width on the stoveture, but I will immediately cut and handle the edges of the tile with a grinder. I admire the tile with the tile with the already glued scotch and put a mark for the cut, adding the thickness of the tile and the gap to the glue - so I immediately take into account the thickness of the tile, pasted into the end of the niche.

Now I will spend the line on the scotch for previously the mark.

In this case, the tape protects the tile from the enameling chipping.

For circumcision and subsequent buris, I will use a small grinder. Pay attention to the disk that is installed here.

This is a stone disk and concrete, which has notches on the cutting part. And there is also a disk with a solid cutting part - there are no notches on it, and it is designed to cut the stone and tiles when cooled by water. Such a disc is not suitable for cutting the tile with a grinder, however, they can try to take a snap.

A lot depends on the quality of the manufacture of these disks. Do not be lazy to see options in the construction store.

Be sure to use safety glasses and gloves when working with a grinder.

At the beginning I will perform a trimming of the tile with a grinder on the planned line. This operation must be done without hurrying and abide by caution, so as not to go beyond the line.

This cut is performed at right angles to the tile. Deleting an excess part, slightly ground the edge.

Execution of snakes

But now, on this edge, I will perform a burrow, that is, styling under 45 degrees. Of course, a certain skill is required to perform this work, but it is easily trained, and here are the main features:

Bulgarian disc all the time is at an angle of 45 degrees to the tile.
Moving a disc on the tile, remove a small part of the edge. Move up-down move smoothly.
Try not to hurt the glazed edge of the tile. Leave about 1 millimeter to it. So you will avoid unnecessary chips.

When the coarse burner is performed, it is possible to remove the scotch.

Let's look at the edge of the tile. As you can see, it washed at an angle of 45 degrees.

And now we will bring this poke to the perfect state. I do this with such a simple device. This is a slight medium sized leather and a small bar. The bar is placed on the skirt, and now the final grinding is performed at the washed edge.

The bar allows me to follow the corner of grinding. It must also be 45 degrees. Movements should be light. Visually I am all the time controlling the return glazed edge and try not to touch it. Having finished grinding, I check the quality of the crawling performed and, if necessary, I spend the grinding again.

And how qualitatively the buris is performed, you can immediately check, docked the two dried tiles.

In the resulting junction will immediately be visible errors. They should be eliminated, especially if you plan to dock the tiles in a seamless method. In my example, I used a simple snack tile in a niche using a seam. Show at the junction of two tiles I chose the size of a remote cross, which is used for this wall tile.

Sometimes the loading of the tile under 45 degrees is a good option for its docking with a window opening. And then such a junction will look so beautiful.

In conclusion, I would like to note that an alternative to hand-drunk with the help of a grinder is the use of a wet cutting machine with adjustment of the tile position.

All rights to video belong: Dohow.

There are a lot of ways to lay ceramic tiles. Some of them suggest additional treatment of the tile. For example, in order to assemble the "Christmas tree" on the floor or perform a straight angle when lining niches, ventilation or engineering boxes, you will surely need a tile cutting at an angle of 45 degrees. It allows you to form a fairly neat straight angle from two separate modules. A story about how to do it, which tools may be needed to perform such works - the subject of this article.

What is needed under construction under 45 degrees? Such an operation becomes in demand in two cases:

When there is a need to docile the outer and inner corner of the rectangular elements, when it is necessary to perform an edge to the edge, helps form a beautiful level angle. This operation allows you to abandon the use of cheap plastic corners.
When a diagonal layout of a tile is selected for cladding. In this case, it is necessary to cut the tile itself at an angle of 45 degrees.

You can carry out a similar task with different tools.

What to cut?

The execution of a bevel in the language of professionals can be called differently: I washed, snacking, the Kremlin angle, climbing tile under 45 degrees. To perform high-quality cladding, you need to perform the described operation to perform tools that will allow you to do smooth without chip. Certain construction Bulgarian, electric tiles or glass cutter is capable of cope with such a task. The use of each type has its advantages and disadvantages. It makes sense to get acquainted with the technology of the work of each instrument.

Construction Bulgarian.

Building Bulgarian is in many houses. If it is necessary to solve the problem with it, although it is not easy to do so at home. To cut the tile, install a diamond disk. The tile is installed under the edge, glazed side down. Then the Bulgarian turns on and the rear part of the tile at an angle of 45 degrees is stepping. It will not be able to get smooth from the first time, so after forming an angle, it is necessary to go through the diamond disk on the surface of the edge being processed. In this case, it turns out a clean and even angle.

Note! In order to form the desired angle, it is necessary to use a grinder, which has a speed adjustment function. It is important to start work on minimal revs, otherwise the tile (its processed edge will melt, burn, but not grinding).

Electric tiles

Any professional brigade will prefer to solve the problem with the help of electric stoveturis. This device works in two modes: one allows you to perform smooth cut, the other is a sharp at an angle of 45 degrees. Using the second function is easy to make any cutting angle from 0 to 45 degrees. The main thing to set the desired notch on the setup pane.

The following tools may be needed to perform work:

Painting tape.
Pencil.
Line.
The machine itself with a swivel bed.
Bulgarian, which has revolutions adjustment mode.

Algorithm Operations Next:

A painting tape passes on the tile.
Pencil and ruler is taken in the hands. With their help, markup is performed.
The tile is laid out on the platform of the tilt corner at an angle of 45 degrees.
The principle of operation of the electric stoveture is the same as the conventional circular saw. Cuts are made by a diamond ribbon so that the tile is not melted during the operation, water is supplied to the place of sawing. She immediately washes off dust and trash.
Ipell it turns out beautiful if with the help of stoveturisses it is possible to get a bevelled angle without damaging the glaze layer (it is important to cut only clay). If the disk to touch the layer of glaze, the angle will turn out with ripped chicken edges. After completing the cladding, the two docking elements will look sloppy and ugly.
Only an experienced tiler is able to cut the glaze and at the same time make the edge smooth. And all because he knows certain professional secrets.

To do this, first with the help of stoveturosis you need to make a smooth slice, and only then try to form the desired angle from the back side. The clawed layer of the glaze is then simply processed by sandpaper. After this tile will look neat.

How is the sharp angle?

It is not enough to breathe on a tile at an angle of 45 degrees, it is important to be able to properly put and form a straight angle. The operation of its creation consists of several stages:

First, the first tile is put on the glue, it is aligned with the help level. It is leveled so that the cropted edge "slightly flies" for the plane of the angle of the base.
After that, the second tile is glued to the wall, on the other side of the angle. For fixing the tile uses glue. Each variety of adhesive has its own time. While it is, you can easily adjust the position of two touching modules. With the help of such a scheme, all subsequent rows are laid out.

Note! In order for a straight angle to be smooth, you need to make sure that the vertical of the walls is withstanding. If the walls have, at least a slight difference of heights, the angle at the top will not come out. To disguise such a defect or distract attention from it already, then it will not be possible.

Not everywhere you can form direct angles. Due to the narrowed edge of the tile, they become fragile, which is why, when finishing, experienced masters never use the described reception. Where pedestrian traffic will be intense, the tropped tile will quickly betray or split.

The docking angle of the steps on the stairs is best to sow a metal corner or laying the tile of the brass, the upper element on the wall of the end.

It is not necessary to form an angle with the help of a tile trimming where there is a chance to touch the wall and knock it down under pressure. Since plastic corners today are a movietone, you can replace them with aluminum planks. This solution looks quite effectively.

How can you make a snack without plastic cutting and grinder?

Sometimes at home it is difficult to find a professional building tool. But in this case, manually can be done to live a tile. It is necessary to act in this case as follows:

From the front side of the tile directly on the glaze glass cutter is drawn.
The tile turns over and the grinder on the site of the future cut is made the groove, similar to the English letter "V". The groove is cut onto the entire tile width.
After that, it remains gently breaking the cut and bring it to sandpaper.

Purified mosaic

Mosaic is the same ceramic tile, it is also actively used in the design of modern interiors, so sometimes there is a need to perform a spice at an angle of 45 degrees on small modulos. How to do it?

To work it is better to use electric stoves, if there is an experience of the grinder, it is also able to come in handy. If there is a stoveture, as practice shows, cut the mosaic with icing up is not very convenient. And all because the structure of the formed models is very moving, it is constantly moving, so it is better to turn the tile with an inlet up, fix it from the back of the cutting disk and, supporting the hand, washed. We will have to suffer a little, but the operation will still succeed.

And it remains an important condition - when processing the edge, you do not need to reach the layer of glaze. The mosaic treated in this way is most often used when designing niches, boxes, under which engineering communications are hidden in the bathroom and in the toilet.

Run the grinder will also be quite difficult. This process is pretty dusty, and it is necessary to be prepared. The mosaic in this case also stacked the face down. During operation, the tile must be squeezed to the surface of the base. You can use the appropriate plywood for these purposes.

Spell is performed slowly, clay is removed by a layer behind the layer. Diamond disk should work all the time on the smallest turns. Perform a caught carefully the grinder will fail. Therefore, the cut will be necessary to refine the file or sandpaper.

Generalization on the topic

Recently, many, performing the lining of the walls of the cafeter, refuse to use a plastic corner. Refusal every time it sounds differently. One fails to pick up the color of the plastic ceiling to the color of the ceramic tile, others prefer to use in the finish as few additional elements as possible, others simply love to experiment and try something new.

The very idea, to do the tiles at an angle of 45 degrees and dock the tile at a right angle, not Nova. It was often used builders when cladding marble facade front elements. Now such a reception began to apply when the niche is designing, boxes, which are hidden engineering communications. It allows you to get a fairly interesting solution. But using it, it is important to know that the angle on the tile, sharpened at an angle of 45 degrees, has its technical disadvantages.

First, the angle becomes fragile, it is vulnerable, any strong blow can destroy tile facing. Therefore, such a reception cannot be used when finishing the surfaces located in the passing plane. It is enough to hook an angle with a metal bucket, and it cracks and turns out, either in choking.

Secondly, such a finish option significantly increases the laboriousness of the work, which means that the final cost of repair will increase markedly. The formation of a straight angle with the help of a shell requires the use of professional construction equipment. Therefore, despite independently experiment in the described direction, you need to think well and weigh all the "for" and "against".

We offer services for cutting tiles at an angle of 45 degrees in Moscow. I washed the tiles under 450 on modern European equipment. Without chips and scratches strictly according to your sizes. Any volumes and complexity. We will take the tile from the object and deliver the finished material after 24 hours. Wholesale customers provide good discounts.

Cutting at an angle of 45 ° - what includes?

Material fence with object
Neat cut at 45 ° without chips on high-precision equipment
Cutting is carried out with a diamond ribbon with automatic water supply
Processing, grinding edges
Removal of the champers AS A GIFT!
Delivery of finished material on the customer's object

Old price from 480 rubles / pm

New price from 330 rubles / pm

Minimum order from 2000 rubles.

Cutting of any kinds of tiles

Our work

We save time and money of our customers!

The specialists of our company will come to the object will die, will drive and bring ready-made material at a convenient time for you. We carry out the cutting of any complexity and volumes, in particular, we work with large-format plates. Ready to perform cut ceramic and porcelain tiles for cladding walls, gender, arrangement of stairways of private and commercial objects.

We work both with individuals and legal entities, and with long-term cooperation are ready to offer favorable conditions.

Our advantages

His shop

Its production + modern equipment
Low prices

Cost of cutting at an angle from 330 rubles / mp
Speed

Perform your order in 24 hours.
Tile delivery

Carefully and gently deliver your order
Customer orientation

Cut both in type and non-standard sizes
Large selection of services

Any types of cutting tiles and porcelain stoneware

The company "House of Tiles" has been providing professional cutting tiles and porcelain stoneware services for more than 10 years in Moscow and the Moscow region. During this time, we have implemented over 10,000 projects of various complexity, including we produce crook tiles at an angle of 45 degrees.

Cutting tiles 45 ° is a time-consuming process that requires a special approach and high-precision technology. This is especially true of expensive and fragile materials. In our work, we use modern equipment from Europe, which accurately and gently cuts the tile to the desired angle. Cutting takes place at low speed, and while driving water. This is necessary for the prevention of cracks and the safety of the material. The use of high-quality equipment and compliance with all standards of cutting allows us to get clean, smooth, neat cut without chips. But still, for 100% quality, we produce an additional grinding of the edge.

Want to order cutting tiles at an angle? Do not lose time! You have already found the most advantageous offer.