How to collect a ram in a warm angle. Types and methods of angular compounds when erecting wooden houses from a bar. Connection to the angle one-sided

In a wooden house-building there are several ways to cut the corners: cutting in Poledev, in a warm angle, in a swallow tail, on rectangular keys IT.D. These angles turn directly on site construction of the house.

There are also such angles as: single-line locking grooves (in "Oblom") and four-sided locking grooves, such a type of logging is made on machine machines. For more information about other types of corners of houses and log cabins, we will tell us in the following articles.

We are interested in the most popular and widespread type forged (cutting) corners of houses from a bar. It is in the so-called "warm angle" or otherwise in the spike-groove. Such a gram assembly at home is ideal for houses and baths from a bar, in particular from a profiled timber.

Warm Cut

The technology of cutting into a warm angle is satisfied. Similarly: in one bar make a groove in another brusin the same in size sizes and densely among themselves the walls of the crown of the crown. The angle of the house turns out completely unproduced, reliable, so I got my name warm.

It is stepwise how the cutting in the "warm corner" is visible in the photographs below.

Got marked groaned

Please note that the technology washed with a spike or groove of angular walls alternate on even and odd crowns. How it does not see in the drawing:

All corners of the house or bath are flooded at the construction site directly during the grazing process. One of the wounds of a warm corner, the so-called "swallow tail"

The entire sawn timber is released with standard six-meter lengths. But, most often the houses are large than 6 × 6 m and in this case the timing is needed to be allowed.

There are two types of bruis joint: a connection to the floor of the tree and in the spike groove.

docking method in the floor of a tree

methods for connecting a bar in a spike groove

Also a type of brusade concretions

Installation of Erker (Erker Broj's joint)

Floor Wall Corner House

[Floor Wall Corner House (corner in spike-groove)]

Walls cutting corner of the house (corner in spike-groove)

Stock Foto Corner in a litter of profiled timber

[Inner corner of brusco logs]

inner corner of Bru Wir

The bog of partitions in the capital walls (washed)

[Washed partitions into the walls of the chub]

Putted partitions into the walls of the church

Lags from a bar 150x100 are drowned by capital in the strapping (base of the house)

[Washed the lag to the base of the wooden house]

I washed the lag to the base of the wooden house

Wooden brazen when assembling the crowns of the house or bath bar

[Treasted brazen when assembling a bar from a bar]

Wooden brazen when assembling a log cab

ROYKI (casing) in window and doorways. Method of dealing with shrinkage house. Read more about shrink shrink

[Planning in a house to fight shrinkage]

Planning in a house to fight shrinkage

Profiled timber, as the main building material for capital walls of houses, baths, log cabins and cottages.

[Profiled Bar Main Material Capital Wall Houses]

Profiled bar main material capital walls at home

Installation of brusched partitions Photo (top view)

[Installation of broom partitions (top view)]

Installation of broom partitions (top view)

Shrinkage compensators This and shock supports shrinkage, sliding supports rafters, etc. see more about the shrinkage compensators.

[Shrouter shrink compensators]

Shrobe shrovet compensators

At first glance, it seems that the technologies of the construction of the house from the profiled timber or one-piece logs have long been established and nothing new in this direction is no longer invented. But it is worth noting that over time, established assembly techniques still undergo significant changes. Here, for example, a classic way of an angular connection of a wooden log cabin, the so-called compound "in a cup", due to the appearance of a modern tool transformed into a more technological connection "in the paw", however, such a compound was not without flaws. A new scheme has already been replaced by a new scheme, called "in a warm corner".

The assembly of the angular connection is the most responsible stage in the process of assembling the wooden log cabin, in addition, it is the most difficult thing. From how qualitatively, the angle will be assembled by almost all operational characteristics of the house, this is the service life and exposure to the warming and deformation of the walls, and most importantly, how warm the house will be.

Each of us was convinced that, first of all, the angles were mixed in winter, and if it happens, it is quite difficult to deal with this problem. It is best to take care of the construction phase. There are several ways to achieve good results.

Characteristics with which possesses
High-quality angular connection:

Here everything is quite simple strength, tightness, aesthetics, manufacturability and efficiency, here are the characteristics that first come to us on the mind, but we are most interesting:

Strength. It is known that the timber is fixed under pressure from its weight, as well as the pressure of overlapping and the severity of the roof. But, such compounds should be resistant to possible changes in the linear dimensions of the bar, and the tree, as is known to be deformed, arising from the oscillations of atmospheric humidity and air temperature. Reduce this effect can be used by a bar pre-dried up to 18-25%, in contrast to the material of natural humidity, it will create a minimum of problems, both in the construction process and during operation.

Tightness. One of the main conditions, for that we are building a house to protect ourselves from the outside, walking drafts of little to the pleasure. The simplest decision to avoid draft, it complicates the path to pass the air through the compounds, i.e. We must make the connection of details geometrically more complex.

Types of Brous Connection in Corners

When building a house from a bar, all types of angular compounds can be divided into two types:

Corner with the residue.
Corner without residue

Corner with the rest

Such a connection may have different names: "into a cup", "in the edge" or angle with subservit. As it is precisely an angle with the residue, - during the construction of a log of compounds form in such a way that the edges of the logs go beyond the walls. The docking occurs due to the grooves - one-, two or four-sided. In the first version from above, the timber is made in width, which corresponds to the cross section of the upper segment. And when cabing a bilateral groove, the same inscriptions are made, and from above, and from the bottom, and in width, and they are equal to the quarter from the height of the lumber.

To increase the strength of the structure, a four-way connection is used. In this case, the inscriptions are made from four sides. Laying the timber of such a form is very convenient, the crowns in this embodiment are located over the other transversely. In order to ensure additional tightness, the angle is filled with insulation between the crowns - it is usually a flaxable panel or a jute insulation.

The main positive qualities of the corner connection of the bar with the residue:

It has a high degree of reliability and does not need additional fixation. At the same time, the crowns located on top reliably hold the lower pressure by their own mass. The offset of any elements of the walls in this case becomes impossible, even with seismic oscillations.

This version of the connection is very technologically, to prepare the grooves on the bar in advance in production conditions, and then compactly assemble the designer on the object.

The main minutes of assembling corners of a church with subservards:

As a result of drying and shrinkage, after assembly, slots may appear in the angular connection, in this case the grooves can freeze and blow out. It is almost no possible to organize tightness and insulation.
There is an obvious reservoir of the material used, since the logs, as a rule, should be significantly longer than the structure itself.
And of course, repellent ends essentially interfere with the external finish of the house
Ends crack and require special processing

Corner without residue

With this type of construction of the house, the parts used are cut exactly into the required size. It is important to note that the docking in the angular parts is made in such a way that the ends are located in the same plane. Such a structure is obtained more accurate and aesthetic. Several ways of connecting timber in such a log corner are used. But, as a rule, only some are suitable for the construction of residential premises.

"Job"

Details for this method are stacked in the joint. For the connection, a specially adapted element or a screwdriver is used for fastening. This embodiment is typical for the economic premises. The log house built by this method initially does not imply the presence of high thermal insulation characteristics, so such rooms are not intended for living in it during the cold season. This connection of the angles is possible to apply to the construction of a country house, which does not claim year-round accommodation. To improve the thermal insulation characteristics of this type of connection, use the installation of an additional duct across the connecting seam.

"In Polterev"

This method can significantly protect the room from drafts, but still these characteristics are not enough to build a warm dwelling. This method shows itself well for the structure of dacha or light garden houses.

"In the paw"

It manifests itself as a more modified version of the previous structure. This method is considered a simplified version of the classical method of an angular connection. In the old days in the paw rubbed from a bobbed log. This method is suitable exclusively for the first crown and the upper strapping, but in no case is not suitable for the construction of the walls, because it has a through slit.

"Dovetail"

This type of docking is suitable for logs and timber. Because of the special form, he washed after saturation of the tree moisture or, on the contrary, during its drying, the details of the compound does not change its original shape, thereby preserving the protection of residential rooms from the penetration of the cold. To eliminate the gaps, they close them with the help of insulation, and then trim outside.

"Warm Corner"

Disadvantages that are described in the methods above are completely absent when assembling "in the warm angle". This connection is more suitable for a profiled timber. At the end of the bar, a special profile is cut, with a compound, it completely eliminates the possibility of blowing the corners. To achieve a completely dense pairing, a special groove is cut down. It is located inside the barrel, which is used for the joint, and on the mating side of the bar form a thorns, which ensures excellent tightness.

This type of compound, which is also referred to as the "indigenous spike" retains walls from offsets, and provides unsurpassed wind protection.

With this type of assembly, the slit also requires sealing using the insulation, and then the objects of the angle outside.

If construction is scheduled not just a household building, namely premises for permanent residence - should choose the most suitable types of corners for this - "warm angle" or "lobby tail". The second option will require the performers of certain skill, so it is necessary to take into account that the assembly in the "Lastochny Tail" may require additional financial expenses.

SP-FORCE-HIDE (Display: Block; Background: # F5F5F5; padding: 10px; width: 450px; max-width: 100%; Border-Radius: 8px; -Moz-Border -Radius: 8px; -WebKit-Border-Radius: 8px; Border-Color: #dDDDDDD; Border-Style: Solid; Border-Width: 1px; font-face: arial, "helvetica neue", sans-serif; background- REPEAT: NO-REPEAT; Background-Position: center; Background-size: auto;). SP-FORM INPUT (Display: Inline-Block; Opacity: 1; Visibility: visible;). SP-Form .sp-Form-Fields -Wrapper (Margin: 0 auto; width: 430px;). SP-Form .sp-Form-Control (Background: #FFFFFF; Border-Color: #CCCCCC; Border-Style: Solid; Border-Width: 1px; font- Size: 15px; padding-left: 8.75px; Padding-Right: 8.75px; Border-Radius: 4px; -Moz-Border-Radius: 4px; -Webkit-Border-Radius: 4px; Height: 35px; width: 100% ;). SP-FORM .SP-Field Label (Color: # 444444; font-size: 13px; font-style: normal; font-weight: bold;). SP-Form .sp-Button (Border Radius: 4px ; -Moz-Border-Radius: 4px; -WebKit-Border-Radius: 4px; b Ackground-Color: # 0089BF; Color: #FFFFFF; Width: AUTO; font-weight: 700; Font-Style: Normal; Font-Family: Arial, Sans-Serif; Box-Shadow: None; -Moz-Box-Shadow: None; -Webkit-Box-Shadow: None;). SP-Form .sp-Button-Container (Text-Align: Center;)

During the construction of a house and a bath of a bar, two main types of corners connect are used. It is a cut of the angles of walls "In Polterev" and "In the warm angle" or otherwise »Ship-groove" It is about these types of compounds that will be discussed:

Type of compound "Warm Angle"

Connection B. "Warm Corner" - This kind of connection of the corners is reliable, effective and has long been used in low-rise construction of bruschers, baths and other wooden buildings.

The essence of the method is as follows: in one of the conjugated bars the inner side of each angle, the spike of a certain size is cut down, in the other, the grooves with the same dimensions will be cut down with the first timber.

Most projects require a deforestation of a groove and spike size in ¼ or even 1/3 of the thickness of the bar. Then, when the walls of the walls, both conjugate timber are connected. It is very important that the connection of the spike and the groove can be as thick as possible, the smallest of the gap between these two elements, the more heat will be the corner.

For a better connection of spikes and a groove in modern construction, an interventic insulation is used, which can act as vegetable felt. It provides even better tightness of the angle. In addition, to ensure a more rigid dressing, various layers of bars alternate spikes and grooves.

Knot docking angle "Warm Corner"

Technology "Warm Corner" or otherwise in Schip-Pazprovides the strength of the structure, due to the absence of gaps between the bars, the external attractiveness of the construction and, most importantly, excellent thermal insulation.

Type of compound "in Polterev"

The next version of the Wheel, which we consider - Wheel "In Polterev" - This is the method whose name has been gained by removing on the corners of the top or bottom half of the thickness of its array. The collection begins with drilling in the corners of the holes of the holes under the heel with such a calculation so that one heel can connect several bars at once.

After laying the first crown, connected by molecules in the corners, the sealer is put on it and the bars of the next crown are put. After performing the angular compounds of the second crown, proceed to the rallying of the crowns among themselves. To do this, in the second crown, after 100-150 cm, the holes are drilled and scored braided. The heater, clogged into the second crown, must enter the body of the first crown at least than half of its thickness. If the long - not less than 2.5 crown thicknesses, and the tool allows you to drill holes to such a depth, then the third crown is placed and there are three crowns at once.

Knot docking angle "in Polterev"

This compound is used as the main way when installing the strapping houses from Bruus and with an increase in the length of the bar by connecting several bars. In addition, it can be used when erecting walls with a mandatory subsequent trimming decorative material. It is used as the main one by many construction organizations.

The strength and heat engineering of the wooden structure in a large extent depend on the type of angular wrist. The builders of the old Slavic settlements did not hold the options for its manufacture in the secret. Thanks to their oral master classes, proven folk technologies were able to preserve. Carpentry traditions have been significantly enriched at the expense of foreign experience and the introduction of useful improvements. Knowledge baggage accumulated weighty. Now in wooden construction, a variety of ways are used to carry timber and logs, one of which has to be used to build their own bathhouses.

Two "indigenous" families of louds

The fundamental criterion for dividing the methods of writing into two large classes - the presence of either the absence of bypass. So the folk masters called the remains of the log, and then the bars leaving on the ends beyond the limits of the circuit of the wooden structure. Relying on this indicator, in the technologies of the structure of the log cabins, I highlight two main fees of cutting:

"In the bowl", according to which the angles are cut down with the residue. This is the most common way that has a mass of variations of domestic and foreign origin. Minus nodal bowls in a tangible consumption at all are not cheap material, plus in excellent thermal insulation of the angle. Yes, and looks on the bowl of the structure quite effectively.
"In the paw" or in a simple "no residue". According to it, the contour of the structure is styled precisely according to plan. With an equivalent material consumption equivalent, the internal dimensions of the structure are larger. The corners chose in the paw in the paw require mandatory cladding, otherwise they will be bludging and mocking. Frams, built without reversal, can be seen by clapboard, block house, plastering, lining with brick or sandwich panels. Unlike options with the bowls, they are applicable here, and sometimes it is recommended all the directions of the finish.

One of the fundamental rules states that all angular compounds must be performed according to a single scheme. Since the wrist of a bar and log walls was carried out according to the scheme "in the bowl", then it will be necessary to cut down the partitions in the same way. Immediately draw attention to that all existing methods are applicable for corner connections in the log winties. But the bath from a bar is cut primarily in the paw, but the occasion is also used and a number of cup-shaped types.

Both classes of corner wrist "covered" by an impressive number of subsidiary subspecies that differ in the complexity of manufacture and heat engineering qualities. The choice of the best way is determined by:

performer's experience;
climate specificity of the terrain;
the period preferred to take bunny procedures.

For the assembly of the crowns of the countryside, operated only in the summer hours, the simplest ways of writhing are suitable. Especially if the owner is going to build a bath at the country site alone. The customer of the brigade of the masters in need of a warm structure for year-round use should not refuse to choose a challenging technological scheme. Information about the differences and features of the wrist will help both the independent performer, and the excitement of builders, who wants to spend money not in vain, make a reasonable choice.

Options for cutting with the residue

The most accessible for a novice carpenter by making an angular node recognize the cut into the bowl, i.e. With the residue of the log on the end. In the "cup" class there are simple and ultra-empty technologies. In wooden construction, it is important to understand: what is easier to chop, will heal less and serve. However, without carpentry skills and knowledge in this art for the manufacture of complex structural recesses, it is better not to take.

Simple Bowl Making Algorithm

For the production of cutting into a simple cup in the log, two grooves in the shape of half-cylinders and a longitudinal interventored furrow, called a lunar groove, are selected in the log. All deepening in the log is made from above, which is very convenient for the wizard, but not good for the walls. In the hole deployed to the sky easily, moisture is easily selected and dust falls through the pairs of density due to drying. Therefore, simple bowls need constant renewal of cacopa.

The owner of the cylindered material does not need to suffer with preliminary preparation. Calibrated logs have a single size, the installation grooves are already selected in them. Even the manufacture of angular recesses. Cylindrid manufacturers can be done if an order and intelligible design documentation goes to them. The buyer of the sawn forest is to be processed: to make, dry, choose a longitudinal moon-shaped furrow for reliable bumps of the crowns, and then start to wheelhouse into the bowl.

Sequence of work on the manufacture of simple bowls:

The squeezed log on the sister-in-making place for marking.
If the longitudinal interventovaya groove has not yet been made, on the thin end of the lower log, in the upper part of which removing is to be made, draw a line equal to the width of the future groove.
Slide the legs of the factory or homemade feature to the width of the placed mounting groove.
Stinn the line with legs to the humps laid in the log cabin and trying to it the upper fellow, then we scratch the sharp legs on the lower log, the exact profile of the upper element, "ocked" the log from all sides.
Having completed the marking of the groove, spread the legs of the line to the distance equal to half of the average radius of the log layered above.
Strip again the legs of the drawing carpentry tool to the approximate and to the lower log lying across the side to describe the half-cylinders of future angular recesses.
We will remove the approximate upper element of the cut, and on the lower log, we will make a pressure that do not reach the depth of the drawn recesses 7-10mm.
We choose an ax that marked withdrawns and finalize the surface of the shinebel.

The method of manufacturing an angular connection based on a log cabin in a spike bowl is presented to the video:

There is no special difference in the sequence of actions. You can chop first a groove, then angular notches or in reverse order. The main thing is that all three constructive components are accurately extruded. You have to get caught by anyone: it will be necessary to try on and put the surplus if the top log is "sees" into the log cabin. Therefore, with the final sample to the protruding lines is not in a hurry. It is desirable to gradually bring it to mind to the mind, so that it is too big samples not to spoil the material. In the old time, the first time the crane mounting recesses smeared tar and put the top element on it. The lavety marks indicated where they still need to pose.

Subsidiaries Bowl

The cutting of a church in the bowl attracts inexperienced performers simplicity and relatively small labor costs. However, without additional castle elements, it is very hard for heat. For the construction of a summer bathhouse, this is quite acceptable. For the construction of a warmer building, the lock knot is better to supplement the selection. The way of cutting is to complicate, but heat engineering will improve.

In the list of the nearest "relatives" technologies for shutters in the bowl:

Cutting into the overojen (she is in the chop), which is a mirror reflection of the bowl. This method is also called Siberian cabbage. It is distinguished by the fact that the angular locks and the lunar groove are simply turned down. The lower orientation of the excavation eliminates the penetration of moisture and dust into the nodal conjugation, so that the insulation does not deteriorate and does not mock the log house.
Bowl with a protrusion. It appeared as a result of the popular improvement of methods in the chille and in the region, according to which the deforestations are made either from above, or the bodies from the bottom. The cutting of the bowl with the protrusion allows you to arrange a longitudinal groove from below, and the angular notes at the top or proceed on the contrary. Because It will be necessary to lay a log with interventic furrows in the bowl, the excipher configuration cannot be still half a cylindrical. Therefore, a rounded protrusion appeared in the bowl, repeating the radius of the longitudinal mounting groove.
Cutting in the hid. It is to form two equivalent rectangular cuttings on the upper and lower side. The option is simpler, but suitable only for the construction of economic buildings.
Ublop with a gym. In order to optimize the strength and thermal insulation of the angle in the bowl, leavens are left - this is a unwanted quarter in a bowl from the inside of the angle. For dosilets, there will still be a response with a mating log.
Cutting into Kurdyuk. It differs from the simple bowl of the presence in the extrusion of an additional spike that increases the strength of the angular node. Schip is called Kurdyuk or Potomok. It gave the name method and increased the heat engineering qualities of the log wall. Oriented the cutting into Kurdyuk in both traditional parties. The bowl is originally chopped by half of its height, then spikes are turned out. The sizes of the formed spike are transferred to the mating log without special tricks: rolling into a log house and marked the serfs where the response groove should be chopped.

Pretty demanding in relation to the skill and experience of the performer, two ways to cut a log cabin in the hook are considered. The first of them predetermines the cutting of half of the bowl, and the remaining, not disheveled half must be clearly docked with the semicircular cutting of the mating log. The second technology resembles a bowl with a gaze, but the logs are rejected by one Kant, and the opposite side turns inside the building. When cutting into the hook, the maximum log power is maintained, thanks to which the angles are warm and reliable.

This is how the cutting into a simple hook:

Overseas technologies of louds with the residue

The fundamentally Canadian and Swedish schemes of logging are similar to the Siberian technique "in OHLUP". Only the angular grooves and grooves to them have no rounded in the section, but a trapezoidal configuration. This is a good plus, because When shrinking, the Slavic bowls are expanding, because of what they need a periodic subaccination. Canadian and Swedish recess after shrinkage tightly "sit down" on the log died to her. There are no gaps at all, and over the years, dusting is also sprinkling spontaneously.

The technique of execution is different. External distinguish can be partially opposed in the castle area of \u200b\u200bthe "Canadian" log cabin and sharpened by six faces with a pretty "Swedish" crossing. Canadian technology has a good simplified follower - cutting into the saddle.

The extremely demanding point of all the shuttle schemes with the residue is precisely the length of the log part of the log, serving beyond the limits of the structure of the structure. It is impossible to do without a short crossing, otherwise it will fall. For a desire to save not led to the emergency state of a log, GOST for the number 30974-2002 clearly regulated the limit distances: from the end of the log to the center of the breakdown of the bowl should be at least 1.4 diameters of the log processed.

Video demonstration of Norwegian cuts:

Methods of cutting without a residue

Options for cutting cutters in the paw are significantly less than methods with a bowl. The reason for their appearance was not economic considerations, but the desire to remove the wooden Terem in the luxury palace by finishing. The angles in the paw are significantly colder. The capillaries on the ends are open, so the outer side of the angular connections in the paw strongly advise to sew at least boards.

For the construction of a church with the use of the technique "in the paw", a bar is suitable, the yokes - dried into two vertical Cant from the opposite sides of the log. Suitable otlindering and ordinary rounder with vertical left and right-wing trees - "DOOLS". Bolk length, i.e. The length of the side cut is equal to the largest diameter of the material used. Bolk width, i.e. The distance between the trees is 2/3 or 3/4 diameters of the vertex of the finest in the acquired batch of the log. Its and it is necessary to first identify and "fool" as a reference for other logs, so that in the process it is not found that part of the material does not fit under the size of the planned paw. By the way, the nerds can be outset immediately on all the logs, and then go to the manufacture of paws of the selected type.

General Lape Manufacturing Instructions

The straight paw is the simplest scheme in the "laptom" class, so you can try to make it my own. She has all the lines of the upcoming tester strictly vertical and horizontal. So that the angle is blocked less, the paw can be supplemented with a gaze, deposit this constructive addition from the inside of the angle. The most reliable connection in the class is oblique paw, because the inclined planes are not allowed to turn out the elements of the log cabin and carefully retain heat.

It turns out all the variations in the equivalent sequence:

Prepared for processing the damn again we take away from above and below. The depth of the treasure should be equal to the width of the nerd. As a result, we get a parallelogram with one imaginary side and deployed to our square cross section;
The end of the parallelogram is drawn into 8 equivalent horizontal parts.
According to the selected paw type and table sizes on the preceded plane, we note and connect points;
There are lines of future treasures with requiring planes and squads, if it is decided that they should be;
Carefully remove the surplus on the markings and on the first finished paw we make a template for transferring the size of the following logs.

There is no need to independently calculate the sizes of oblique paws, they are in the tables. The masters of them are bothering slowly, scrupulously. The lunar groove is scratched along the logs laid into the log cabin, push the legs of the line to the value of the detected gap.

Corner Wildlings in Brous

Forming a rounded connection in a timber is difficult, and it is not necessary, because for the bruise of the crusted crowns, their techniques have been developed. On the basis of the paws were created identical options with very similar names: Okhenap, Polterev, Kurdyuk.

However, the bar has its own, specific methods and types of angular compounds using plug-in or chipped materials. The walls according to the tradition of wooden architecture are "penetrated" with bellows - vertical wooden nails of 25-30 cm in diameter and height equal to 0.8 from the height of the cut. It should be remembered that between the elements of any connection in the blocking and log cabin, it is necessary to leave a vertical clearance to compensate for the standard shrinkage, followed by construction. In the bowls and paws, the limit value of the gap 0.5 cm, in the mounting longitudinal grooves of 1.0 cm.

We described the common, but not all existing logistics schemes. The difference in the methods of their implementation and in the heat engineer will tell you that it is better to prefer good luck!

The docking of the bar in a warm corner ensures that the structure will not freeze in the winter season. Such a compound excludes purging and due to the freezing of the walls. This method of driving a bar is done in such a way that after installation there are no pass-through slots between the connected elements.

The absence of cracks is achieved due to the fact that the thorn inserted into the groove forms an air lock that prevents freezing and blowing. In addition, all the joints break through Jute.

Jute is the best material for insulation of joints and crowns during the construction of a brusade house. Indicators of thermal conductivity of this material are much superior to moss and pass. Jute does not rot and does not absorb moisture, and the installation process with its use is much simpler and faster.

Straight sip

It is used for the construction of small buildings in which the length of the wall is smooth the length of the bar. This compound is quite reliable to withstand loads arising from the operation of the structure. For example, wind load or earthquake. In addition, during the shrinkage, the load in the corner occurs evenly, and the weak part of the bar remains the whole.

The gap does not pass through

There are some rules in the manufacture of spikes and a groove. Ship should not be too thick and long. Because the size of the spike determines the size of the groove. If the grooves are too wide due to thick spike, the weak part on a bar with a groove will become even weaker.

Size groove

Half of the swallow tail

With this connection, the spike is washed under the cone. According to the characteristics, the connection in half of the swallow tail does not differ from the node described earlier. But the strength rate increases. The conical washed reliably holds the bars and does not allow them to disperse. This compound is used in the construction of walls with a length of more than the length of the bar.

The complexity of the production of docking in half of the swallow tail and in a straight spike do not differ. Both methods are performed using or without a template. For an experienced professional, the difference in the complexity of the implementation of these joints is practically immatched.

Schip half of the swallow tail should not be more than 5 cm in the widest part. Otherwise, a crack will appear in a crack with a groove. This happens due to uneven shrinkage. The figure shows this place.

If the spike half of the swallow tail will be more than 5 cm

Corner Schip

With such a spike technology, has a triangle shape. This method is not completely distributed, because there is no advantage over the above described. But this node is less durable than when docking half of the swallow tail.

As can be seen, in the figure, the node is quite sealed and does not have through slots. Therefore, it has the right to exist. The manufacturing technology is no different from the previously described methods. The builder should only turn the chainsaw tire when cutting into one direction or another, and it will receive one of these types of bruques.

The methods described above have the same heated saving performance. The corners of the house and the baths are not blocked and do not freeze. But in terms of strength, the connection is dominated in half a swallow tail. To make sure that the warm corner is much better than other ways. Consider the connection in the paw.

Connection in paw

Another name "in Polterev". This method is suitable only for the first Vints and the upper strapping, but not suitable when the walls are erected, because it has a through slot. But in the specified places, the use of such a compound is more practical. This comes professional builders. The first and last crown is performed "in the paw", and the walls in the warm angle. Such a node guarantees strength.

Benefits

The warm angle is suitable for building a bath and brusade house due to a closed method of compound.

The house does not freeze and is not blown away.

In the bath and brusade house will be warm and comfortable due to the fact that there are no drafts.

The construction of a bathhouse and a house from a bar is made by a rapid pace due to the simple method of roasted.

There is no excess consumption of materials.

disadvantages

When shrinking a bath or brusade house, a crack can appear on a bar with a groove if the spike is incorrectly made.

Having hired, the construction organization for construction should be coordinated with a brigadier or other managerial way of making angles. After making sure that the work brigade will apply during the construction of a bath or home warm angle they can be trusted.