How to make your hands the clock. Wall clock do it yourself: materials and drawings, design. Handmade kitchen watches

No need to know the clockwork device to make the original wall clock do it yourself. In any house there are also broken watches, and inexpensive Chinese-made alarm clocks. From all this wealth, you can create original and useful decorations for the interior with your own hands.

Why is the wall clock so interesting?

Watches - peculiar guides of mysterious invisible, but all experienced energy called time. Therefore, in the consciousness of a person, the watch is also charged something mystical. The clocks have an interesting, inexplicable property to speed up or slow down their move, as they do. People will always be not indifferent to the clock and by the time to personify them.

How to make wall clock with your own hands?

Pay attention to these interesting designer solutions. The photo shows that creating original wall clock with their own hands quite under the power of a simple housewife. As designer decisions, such a watch made by your own hands will be the most bright and attractive place for your interior!

Here it is necessary to proceed from the fact that the dial can be anything. The main thing is that such hours must be beautiful and, as design items, be sure to carry some idea.

Creative thought that received a direction is very fruitful. If you once feel like a designer, then this is already forever. And such a fertile direction as the creation of original wall clocks is simply inexhaustible.

Here is the photo of the dial made from the lid of a large wooden coil on which the cable were wound before. Here, the designer saw exactly the interesting texture of the lid as a circle, not paying attention to the main purpose of the subject. Stencil inscriptions and a metal lining on the coil hole. How it is impossible to emphasize the idea of \u200b\u200bthe dial from wooden planks.

The watches from the Globus halves require a lot of space, but look awesome. Such watch-songwrites will suit and give the spirit of travel. By the way, such clocks can well approach the agency's tour.

Wall clock with create something such a homemade, similar to the grandmother's chest ...

And the clock-ball with rounded arrows is a real time machine.

Wall-mounted pictures and the following image, the clock from a draped unusual material of a flat surface can come for a living room and a hall ...

An interesting color solution visually hides the arrows on the clock, and the watch-card will allow you to travel for some country. You can additionally specify a lot of different data, mark the places where you were. Very original designer solution for wall clocks made by your own hands.

But these laconic watches in the form of a chessboard are well suited to the strict style of the living room, a cabinet or library.

The clock from the tin can is of course for the kitchen. The following photos clearly seen that even such an abstract thing, like a clock spring, can be the subject of decor.

A very interesting solution to make a dial of a drink of wood, and arrows from the twigs.

Figures, carved from old records, can be highlighted in a separate type of creativity. They themselves are very creative and have the right to life. But in combination with the idea of \u200b\u200btime pointers just super!

Wall clock design do it yourself

People very often, accustomed to a certain setting, do not decide to make at least the slightest changes. And this static is so contradicts the creative spirit sitting in each of us. Try to change this statics, start with original wall clocks made with your own hands.

Watch with your own hands. Step by step instructions with photos

Author: Bulatova Elizabeth, student 6 in class, MBOU "School No. 1" of Semenov, Nizhny Novgorod region.
Description: The master class is designed for schoolchildren, parents and creative children.
Purpose: Interior decoration.
purpose: Making hours with your own hands.
Tasks:
- develop individual creative abilities, fantasy and imagination;
- to educate prudence and accuracy.
Materials and tools:
1. Clock mechanism
2. Scissors
3. Clay
4. Decorative decorations (ribbon, rhinestones, glitter, sisal red, paper cord)
5. LINE
6. Wire
7. Cardboard
8. Discs (7)
Safety with scissors:
- work with scissors carefully;
- Scissors must be well adjusted and sharpened;
- put the scissors to the right with closer blades directed from ourselves;
- transmit scissors to rings forward with closer blades;
- when cutting, a narrow blade of scissors should be downstairs;
- Store scissors in a specific place (box or stand).

Safety when working with glue:
- when working with glue, use the tassel if it is required;
- Use the amount of glue that is required to perform work at this stage;
- It is necessary to apply glue with a smooth thin layer;
- Try so that the glue does not get on clothes, face and especially in the eye;
- after work glue tightly close and remove;
- Wash your hands and workplace with soap.

S. Usachev "Clock"
The clock go over the days of day.
The clock is running over the age of the eyelids ...
- Where are the clock? -
Asked once a man.
The clock was terribly surprised.
Thought.
Stopped.

The history of the invention and the development of hours.

The first primitive concepts for measuring time (day, morning, day, noon, evening, night) Ancient people subconsciously suggested a regular change of season, a change of day and night, the movement of the Sun and the Moon on the heavenly severity.
The history of the occurrence of hours is very interesting and informative. It was important to know the exact time to optimally plan its actions, solar, water, mechanical, mechanical, were invented. The result is currently the complex mechanisms that can be seen in modern stores.
The origin of the title of the word "clock".
The word "clock" appeared in everyday life in the XIV century, its foundation was the Latin "Clocca", meaning a call. And before that, the first experiments of determining the time were associated with the observation of the movements of the Sun in the sky. In 3500, the first sunshirt began to be used before our era. The principle of their work was to observe the shadow formed during the sunlight, since at different intervals, the position and length of the shade change.
In Greece, they came to the opinion of the need to divide the year for twelve months to thirty days in each. Subsequently, residents of the ancient Babylon and Egypt were made dividing the day for hours, minutes, seconds, which played an important role in the development of watchmaking.
Joot Berji in 1577 first made hours using a minute arrows. In this product there was also a minute arrow, the oscillations of the pendulum were turned the gear wheel, which, in turn, changed the position of the arrows on the dial. The dial was graded at 12 o'clock, so the arrow passed twice in a circle twice.
Currently, humanity has complex, reliable and high-precision hourly mechanisms created with the involvement of the latest scientific research and decorated in the most diverse stylistics.
Unusual hours, ideally suitable for the style of the interior of the room, is always a good decor element. Not only in terms of aesthetics, but also from the point of view of functionality. These are the original clocks can be made with your own hands.
The clock is the necessary, useful and, in general, ordinary. Few people think about their design, because the main thing is that they correctly show the time.
But try to make wall clock with your own hands - and you will notice that the atmosphere in this room has changed unprecedented.
Of course, it is not about to assemble and adjust the clockwork - it should be used ready, bought in the store or removed from the old hours. But it is very possible to skittase on the design of the dial.

Step-by-step process of performance:

1. Two A4 cardboard sheets stick on A3 format sheet.

2. Circle on cardboard is a circle, after which it is cut.

3. Ribbon wind disks.

4. Wash the paper cord on the wire.

5. Then we twist the wire around the round stick to get the curl.

6. We find the middle of the circle in the ruler.

7. We glue the discs and begin to decorate the clock.

8. Cut the hearts from the disks and wind the ribbon.

9. Heart decorate the balls from red sisal and glue them to the clock.

10. In the middle of the discs we glue the sisal and rhinestones. On the central disk set the arrows with the clockwork.

Such a trifle as ordinary hours can become a central element of the interior if they are made with their own hands. The main thing in these watches is their uniqueness and soul invested in them.

Hooray! I am officially shoemaker with boots. I looked around how participants in our master class in the needle did wall clocks, and now (not half a year and half a year) in our kitchen there appeared a tropical keeper of time.

In early May, the master class was held in our needle, where we did the wall clock with their own hands. The idea of \u200b\u200bVorkshop arose in January, and it was very nice to implement it. Here, very by the way, the clock was broken in the kitchen, which I have long broke out. Compatible pleasant with useful. First, I made a new device to determine the time, secondly, an article for the blog, and thirdly - the tropical decor beloved by me this summer.

Why make the clock do it yourself, if you can buy

And so it is clear that made with your own hands, it is with a soul and from the soul. Perhaps purchased will be shall and with a guarantee, but the advantages to make the wall clock with their own hands more:

you can implement any idea (for example, as mine with tropics)
choose exactly the size that needs
find the right arrows and mechanism
start a little better to understand how the wall clock is arranged
proudly report to everyone that you made them yourself (and this is not just a postcard or flower, but a whole device).

What makes a dial for wall clocks

Thinking about the panel under the dial, it is worth remembering that the clock can be not only round, but also triangular, square, even in the form of a flower.

Panel can be ordered in a laser cutting workshop
find and buy prepared from plywood in the online store or in a store with needlework goods
make from cork substrate or tight thick cardboard
cut from plasterboard
make a drink
or from the vinyl record.

How to decorate wall clock

Ways to decorate wall clock mass, it all depends on your desire to create and bother.

You can print and glue the finished picture.
apply drawing acrylic paints
draw something watercolor, cut and glue
glue volumetric parts from thin plywood
embroider anything on the fabric and cover the workpiece
you can draw or glue numbers.

Wall clock - materials and tools

Time spent - one and a half hours. We will need:

round panel of plywood diameter 30 cm
clock mechanism with arrows
paper and pencil
rule
acrylic paints and tassels
palette for mixing paints
pliers
scissors.

Wall clock with their own hands - work

The mechanism can be ordered in the online store or use the remaining old hours. There is a couple of moments to pay attention to:

Thickness of the dial
thread diameter (must approach the hole diameter in the middle of the panel)
and the sprock height (funeral on, which is still holding, and on which arrows dressed).

For example, in my mechanism of the rod height of only 8 mm, it means that the thickness of the plywood blank should not exceed 4 mm, otherwise there is not enough space to spin the nut. The best overall height of the stock is 16 mm, and the height of the thread is 9 mm. Such a mechanism is suitable for most wooden blanks.

If there are volumetric parts on the dial, you need to make sure that the arrows will not be cling.

1. Before you start making wall clock with your own hands, you need to decide where the number is 12. To do this, turn over the panel, insert the clockwork, outline the middle of the vertex of the mechanism (it will coincide with the middle of the cape) and carry out a perpendicular line. It is from here that the count will begin and the distance between the numbers will be marked (if they are planned).

2. We take a sheet of paper, supply the dial contour on it and draw the decor. It is useful in order to see, harmoniously looks like a composition before it is too late to change something. I re CRED on the paper contours of the leaves, then cut out and moved to the plywood blank using a pencil.

3. Color the workpiece in accordance with the decor. I used a white construction acrylic, an artistic acrylic and a color paste for a tinting.

4. When the paint is driving, screw the clock mechanism. It may have many details that can be used or ignore depending on the thickness of the dial. Usually, the assembly scheme is attached to the hourly mechanism, which I advise you to adhere to. We ride a rubber substrate on the rod and apply to the dial from the reverse side. The top (middle of the peels) should coincide with the pencil margin (see paragraph 1).

5. I turn over the workpiece with a puck and tighten the nut. Here we need pliers so that you can be tightened tightly.

6. We ride the arrows. By the way, the arrows I repainted from white to black. There are also two points here. First, on the arrows there may be a protective film that you need to remove. Secondly, the black art acrylic was not very good for metal, so I had to first challenge the arrows with a construction white acrylic, and then after drying it was black.

Before rolling, you need to make sure that all the arrows are straight. First we ride the hour, then minute. The second dresses the latter. They are rolled to easy click. It is important not to rearrange and not too diligent, so as not to break the gentle fasteners. Arrows should be strictly parallel to each other and do not touch, otherwise the clock simply will not go.

7. I exhibit all the arrows at 12 o'clock according to the mark, insert the battery and configure the correct time using a special wheel that can be found on the reverse side mechanism.

A couple of evenings, one and a half hours - and I gladly launched my time. Take care of your time, spend it with those who give you joy!

Best,

Beautiful wall clocks are always not easy to source about time information, but also decorate the apartment interior, give him a special charm.

And if you think that the wall clock is very difficult to do with your own hands, then you are deeply mistaken. This is a very real task that is practically everyone forces. After all, for such hours, the mechanism itself does not need to collect.

In contact with

Odnoklassniki.

It takes from old hours or removed from cheap Chinese alarm clocks. And on this basis, you decorate them to your taste, taking into account the design of your apartment.

What are the wall clocks

If you decide to independently make wall-mounted or make outdoor hours with your own hands, then you need to know that it can be done almost from any material. Of course, the most popular is wood. Thanks to its properties, the clock from the tree is made of the most different shape and serve long enough.

Usually from this material are independently made not only wall-mounted, but also outdoor hours. By the way, the drawings for the manufacture of wall clocks are usually not required, but they can sometimes need for outdoor structures with a more complex assembly.

Watch from the plate

Plastic and other materials

Also popular with plastic watches. They are even more durable, but their manufacturer is more complicated. Original watches can be made of cardboard, and surprises the simplicity from which you can implement it. As a material for wall clocks, you can use paper or, for example, record stamps.

Note!

The clock in the kitchen is quite realistic to make it from tin cans.

A large variety is different and additional material used mainly for the manufacture of arrows. It can be twigs of trees, buttons, pencils or wire.

Cardboard clock

As we have said, the cardboard watches are made quite just so we will now tell how to make a watch from cardboard yourself. In order to accomplish this idea, we will need the following materials and tools:

Clockwork. It can be pulled out of old unnecessary hours.
Piece of corrugated cardboard. Its dimensions depend on the dimensions of your future product.
Wooden disk.
, PVA glue, kraft paper (special high-strength wrapping paper).
(fine-grained and possibly coarse), hook, decorative elements.

Watch from paper

The main stages of execution

First you need to take a disk from the tree (the same goes on the wooden clock), and the perforator produce a hole under the hourly mechanism. After that, cut out two circles from the cardboard and stick them on both sides and in one of them we also do a hole for the hourly mechanism.

Having made the foundation for the clock, you need to puncture the ends of the disk with cardboard, cutting a piece of width equal to the thickness of the disk and the length equal to its circle. Fix it with PVA glue. Then you need to push the clock-paper clock and, on the reverse side, fix the hook, with which we will hang our product on the carnations. By the way, the master class on the manufacture of hours can be viewed below.

Wall clock do it yourself video:

Finishing work

Now you need to paint our disk black. It will be enough to do it from the front side. After drying the surface, we do the hole under the arrow using the selection for this. Now we need silver paint, which easily contrasts with the black disk color and applied with it using fission and numbers on the dial. The same color stain and arrows. We finish our work by setting the clock mechanism and the decorative decoration of the ends and edges of the disk.

Note!

This can be done, for example, with rhinestones.

As can be seen on the instructions presented, the manufacture of hours from cardboard can almost anyone.

Woods from wood

Let's look at how quickly you can make a wooden clock. For their manufacture, you will need the following materials and tools:

Disk made of wood with a diameter of 330 mm.
Wooden sticks and balls of small diameter in the amount of 12 pieces.
Clockwork.
Emery paper, glue ,.
Flooring and perforator.
Black cardboard and paint two colors.
Pencil, scissors, line.

Step-by-step instruction

Treat the sandpaper disk and balls to a smooth surface and wipe them from dust.
Wooden sticks cut to the same length. I choose the length yourself.
Using a perforator, make a hole in the center of the disk intended for arrows.
Drill 12 holes on the end of the wooden disk. They will serve as grooves for sticks with balls. The distance between the disks should be the same. To do this, use the transportation and make marks every thirty degrees.
Will in the hole glue and fix the wooden sticks in them.
At this stage of the manufacture of clocks from a tree, you need to treat the surface of the primer and after drying, apply several layers of paint. The color of the paint, in our case, should be white.
Now we need to paint the balls in red (it is most suitable for a white disk). So that it was convenient to do, we will need a piece of foam and the remnants of our wooden sticks. We ride the balls on them and make painting, after which we insert them into a piece of foam and waiting for drying. For painting we use spray, since the tassel is uniformly painted hardly.
After drying, insert the balls into the sticks and the "Sadim" on the glue.

The final step will be the installation of a clock mechanism from the reverse side of the disk and fix the arrows to it. Arrows will produce from dense cardboard painted black.

It is interesting! do it yourself - master class

Watch from paper

In order to make the paper from paper, we will need the following materials:

Clock mechanism and arrows.
Dial of wood or other dense material.
Paper for decor and buttons.
Decamental glue (executes the role of glue, varnish and sealant), ordinary glue, paints.
Small paper plate.
Rule, scissors, pencil, pen.
Tassel and foam brush.

Plastic watch

Stages of manufacture

Let's look at how to make the clock with your own hands in stages.

First we cut the paper (choose the color matching color), in the form of an elongated trapezium, along the length of the dial. At the same time, all pieces should be the same in size and form. The total area of \u200b\u200bpaper should be more dial, so that later it is possible to heat the ends. Then fix glue for decoupage paper to the dial and expect until it dry. After that, bend and glue hanging ends to the back of the dial.
We apply to the surface of the dial decoupage glue into several layers. Each subsequent layer is applied to the previous one, but after complete drying. With proper application, the surface of the dial will become a glossy.
We make the markup of the dial. It is convenient to do with a paper plate. That is, first, we place all points on the plate, then we apply it to the dial and put the points already on it. After that, in the place of numbers, we glue, for example, buttons or something else, what your fantasy is designed for.

Please help us make the site better! Leave the message and your contacts in the comments - we will contact you and make a publication better together!

Currently, the decoupage of the clock with their own hands has acquired enormous popularity! This is not surprising: in the age of stress sometimes I want to do something for the soul, and if it will still have a functional and aesthetic purpose, then this hobby is just doomed to success!

Technique Decoupage Watch

If earlier materials and templates for decoupage it was difficult to get, now they are in excess in any bookstore or a department for creativity. You can easily purchase stencils, dials, blanks, arrows, accessories or other attributes for decoupage hours. Therefore, this is a new-fashioned hobby - an acceptable option for beginners.

Consider the technique of decoupage of the clock with your own hands in stages.

Preparation of a stencil. So, you have purchased a blank for the clock in the store for needlework (as in the photo).
Previously, the surface of the workpiece should be prepared: Okrew, if the clock is wooden or degreased if plastic.
Create a background image as in the photo. You can choose any style depending on your preferences or interior features of the room you want to decorate the future masterpiece.
We glue the selected picture on the workpiece (see photo).

Tip! Torn edges easier to mask, so it is better not to cut the image, but simply tear it with your hands from paper.

You can stick the picture on the template or with the help of PVA, diluted with water, or special glue for decoupage. Here the main thing is to act neatly, not allowing folds in the picture. After that, the workpiece of future hours should be dried and coated with acrylic varnish, after which it is again to dry the workpiece. Repeat this circuit three times.

This technique is described in more detail on the video shown at the end of the text.

Choose style

Before you start directly to decoupage the clock with your own hands, you should decide on the style of the future masterpiece. The following decoupage options are now most popular:

provence;
vintage or "under-ancient";
"Hollywood".

To begin with, you should choose the room in which you plan to hang your future masterpiece. For example, if this is a kitchen, then there will be some kind of romantic sketch in it inappropriate, or a Hollywood style watches. On the contrary, Provence watches or Vintage perfectly fit into the interior of most kitchens.

Perhaps the style of Provence is one of the most common and understandable. If the directions of Provence and Vintage resemble each other, the Hollywood style is different from them. So, for him the following nuances are characteristic:

Use as the main following colors: black, red, white, blue. Whatever colors you choose, they should be contrasted with each other if possible and stand out from the background.
Maximum brilliance, the use of all sorts of rhises is welcomed.
The use of images of famous Hollywood actors, preferably Golden Era Hollywood: Audrey Hepburn, Clark Gabla, Marilyn Monroe, Greet Garbo, etc. In this case, you are partially a retro style.

All styles are suitable for beginners. With these options, you can see, looking at the video at the end of the text.

Features of decoupage dial

The finished dial can be loose in the store, but much more interesting to make it with your own hands. So, the numbers on the clock can be made practically from the first things that came across the eyes. It all depends on your imagination and, of course, from the decoupage of the clock.

Suppose you chose Provence style. Then for the dial will appropriate to use corks from bottles of wine, dried branches of lavender, soap in the form of small hearts. In addition, it is not necessary that the numbers are on the dial: just designate divisions.

Idea for clock on the Pink Floyd plate.
The clock on the plate is convenient to do also because the center of the dial for the arrows is accurately marked. However, it should be remembered that the round polygraphic sticker in the center is difficult to "overlap" if it is white. It will be more practical to take a plate with a red sticker for the base

If the decoupage of ordinary wall clocks may seem boring, then for you we also ran out another original option - decoupage of the clock on the vinyl record. The technique of such a decoupage is not much different from those described above, but here there are features:

To begin with, prepare a plate, uploading it with white paint. Give her to dry for a while.
For applying a picture, it is better to use special napkins for decoupage. Two lower layers tear and apply only the top on the plate. Flat synthetic brush applied glue over napkins. Let's dry, after which we cover our workpiece with a layer of varnish. After drying, we apply varnish again.

Attention! Use special varnish and decoupage glue.

We make the markup of the dial. To do this, you can use wine stoppers, seashells and any other items to which fantasy enough.

Tip! Apply the paint with a sponge for washing dishes.

Clock cover at least three layers of acrylic varnish.
We rush with cardboard sticker on the back of the plate. We make a hole in the center and glue the clock mechanism. Attach the arrows, insert the batteries.

Original watch ready!