Snow blower from chainsaw friendship. How to make a snow blower from chainsaw friendship. The principle of the screw mechanism

6339 08.10.2019 5 min.

Small-sized snow blowers that allow you to automate the time-consuming snow clearing process, very in demand. But what should I do if there is simply no funds for the purchase of a snow removal machine?

Single way out is the design of a homemade snow blower From what can be found in almost every garage of a stock owner. For instance, chainsaw which is available in many people, especially in rural areas.

Principle of operation

The design of the factory snow blower is satisfied simple. The main driving force is the motor, From the power of which will depend on the quality of snow cleaning, the range of emissions, etc.

In addition to the engine, in Snowflower device includes:

The housing made of metal or plastic protecting the working units from an outside environment.
A screw mechanism consisting of shaft and screw parts.
The output tube on which the snow will be released outward.
If a two-step system, then in addition to the auger, the impeller is also used (rotary mechanism), which makes snow out into the output tube.
Elementary control systems, handles, clutch, etc.
Depending on the configuration, the wheeled, caterpillars or ski may be present.

The principle of work of the homemade snow blower will not differ from the store. In his package also will include augerwhich is sent screws to the shaft center. It directs snow cover to the blade, which transmits the mass further to the output tube.

If the design provides a rotor, then the snow came from the blade falls at first. It produces additional recycling of the snow mass, after which it is sent to the pipe.

Then the snow is thrown out for a certain distance (up to 12 meters).

Made homemade snowplow from chainsaws has its advantages:

Doing a snow blower with your own hands, you will significantly save money that could spend on purchasing a new snowplow. At the same time, even if you have to buy chainsaw (see), you will still remain in the plus.
Snowplow made with your own hands from or other models will have similar productivity as purchased analogues.
The remaining parts of the body, auger mechanism and other components of the design are made of handy tools, such as metal pipes, iron sheets, etc. This is again to the word savings.

More information can be found in the video above:

The only drawback will be the fact that on a homemade snow removal car from chainsaws it will not be possible to establish a mechanism responsible for self-propelled design. But if you provide peculiar salazzas or skiing at the bottom of the unit, then this task will not be so difficult.

Snow blower from chainsaws has other features:

As an output tube, you can use a practical any plastic tube, the diameter of which will be at least 16 cm.

The control knob can be made independently, from any metal tube.

The width of the bucket will depend on the engine power chainsaws. If it is powerful enough, the bucket width can be increased.

Due to the fact that the homemade snow blower made with his hands from chainsaws does not have self-proposal, better provide peculiar salazzas for the best movement of the Snow Pokrov Aggregate. You can use conventional wooden bars corresponding to the length frame.

They can be attached to the plastic base, which will improve the running racking indicators.

You can highlight Several tips, Helping the unit:

So that extraneous items do not fall into the working engine, you can install special safety bolts that eliminate this threat.

After the first launch of the unit, you need to check all the symbol connections. If required, tighten all the nuts until you stop.

Do preference in the side of the closed-type bearings so that the snow mass does not get inside the housing.

Do not try to remove strongly rambling snow. Pre-prepare coating using a hand tool.

Conclusion

Designing a homemade snow removal machine from available chainsaws is a rather optimal output from the situation when there is not enough cash on the purchase of a snow blower in the store.

Taking into account the fact that the cost of even the cheapest unit can be at least 15 thousand rubles, this question arises sharp enough. (Read about the choice of gasoline snow blower)

The use of the engine from chainsaws is good since that its power is enough for cleaning quite large volumes of snow. At the same time, the power of the homemade snow blower is almost identical to the one that there is at the disposal of the store models (see a snow blower).

This article will tell how to make a snow blower from chainsaws. Such experience was from the participant of our forum STEP139 whichHaving made a homemade snow blower based on the "Ural-2" chainsaw.

What make a snow blower

Step139. Lives on Baikal, where snow during the cold season is the same endless as the famous lake itself. Previously, the forumchanin cleared the site using a conventional aluminum shovel, but once, after a large-scale snowfall, firmly thought about to acquire a special equipment. The electrical option disappeared immediately due to the need to carry a cable. The gasoline and noncommose unit was inconvenient to move the plot on steep slopes. The self-propelled model turned out to be sufficiently heavy, and, moreover, it could not be lowered along the steps.

The last factors bowed to the man to make a snow blower from chainsaws with their own hands, became heavy soils - loams with rubble and remoteness from the city: in case of breakdowns, the store technique would have to carry out for 70 kilometers. The unit he decided to do the most simple, fully iron, but the time is light and maintainable. In such conditions, there will be an ideal snow blower from the chainsaw "Friendship" or any other good chainsaw.

For the manufacture of a homemade snowbreaker, the forumchanin took:

chainsaw, which was idle in the garage with distant Soviet times;
metal sheet 1400x400 mm and 2 mm thick (blades and blades);
700x800 mm stainless steel sheet, 1 mm (bucket casing);
shaft D20mm L \u003d 800 mm;
pair of bearings D48 / 20 mm pressed from two sides into the pipe;
two unnecessary arcs (square 20x20 mm) and two crossbars (also 20x20) from the greenhouse (frame);
nuts, washers, pieces of angle 35 mm and metal, a strip of 2 mm wide and 40 mm long needed for fastening the casing to the side walls;
the crown of the back of the star from the Motocycle "Minsk" (Big Slava Star);
asterisk from the motorcycle "Sunrise" (presenter, small);
chain from the Motocycle Minsk, "Sunrise";
snowmobile brake cable;
gas tread;
rubber handles from a snowmobile.

Almost half of the materials and consumables from this list participent site found in my garage, the rest had to buy in the store - for it Step139. Spent 801 ruble.

How to make a snowplow machine

Step139.:

- Constructively I represented the unit as a regular auger in the bucket on the bearing with a chain transmission on a saw. Here are two options at once - chain outside the bucket and chain inside. I was more like an option with a chain inside, because in this case the shaft is clamped on both sides by the side walls of the bucket. I did not find the wheels, and I stopped on the polls. In the manufacture, they are easier, you can be bent out of any pipe (arcs came in handy from the greenhouse). Due to the fact that the pollocks are swinging, you can adjust the height of the cutting edge of the bucket from the surface (this is the topic of capturing stones on the first snow).

Browsing the rollers about snow blowers on the Internet, Step139. concluded that the shorter the frame and above the handle, the greater the probability of breaking the auger. This mistake forumchanin decided to avoid when designing his "snowplow".

Step139.:

- Personally, the most complex in the design was the manufacture of auger. But everything turned out to be easier than I thought. Based on that, the auger will consist of 4 blades (2 pcs. On each side relative to the center) and 2 blades in the center, and that the end diameter of the auger will be 300 mm, I began to count the feather blade. The bucket width took approximately 600-640 mm. The width of the blades is 120 mm.

On the forum, the People's Skillmen brought very detailed mathematical calculations and even published their drafts together with its homemade drawings. It decided to make a spiral blade with a diameter of 300 mm and a width of 220 mm with a width of the working part of 70 mm. For this, the forumchanin used a metal sheet with a thickness of 2 mm - the grinder and the jigsaw chopped out the ring from it, and then with the help of the vice stretched them into the spiral. This work was severe in physical terms.

Followed from the same steel Step139. With their own hands made the blades, cut out from a metal corner plate and started assembling a screw into a single whole. On the smooth surface, the blades fell perpendicular to the shaft. From the blades measured 220 mm and welded two side plates. After that, clamps clapped the blades to the shovels and plates and braided all this. The central jumper of each blade should be tightly pressing to the shaft, and the jumpers in each pair of blades - to accommodate strictly opposite each other and at a distance of 110 mm from the side plates and the blades, i.e. in the middle. Metal 4 mm Forumchanin cut a disk with a diameter of 110 mm and screwed to him bolts of the rear star from the Minsk motorcycle. Then cut the shaft under the size, taking into account the gaps with the side walls.

In search of metal for side walls Step139. Seven times searched. There was even one thought to cut a public garbage into pieces, but in the end, the metal was still found. And since the most difficult part of the work - the manufacture of auger - was already done, then the events developed quickly: the forumchanic made the bucket casing, installed auger, the engine with the chain and the remaining parts. Participant website began to collect his snow blower for a week before the new year, and in January spent the first tests.

Step139.:

- If someone gathered to make a snow blower, fasten everything with the pucks of the engraver, twist on the lock nut, in short, clamp to death. The other day I was unwound a bolt (it stands on a clamp that presses the gearbox to the engine). Well, the saw was fixed in front and rear, but it would fall apart into two parts. Vibration, though small, still eat.

Detailed story Step139.about how it collected the unit, the photo of all schemes, calculations and the process of manufacturing a snow removal machine can be found in the subject of our forum. And if you have already had the experience of assembling a snow blower or other garden equipment, share it with other participants site. We are waiting for your drawings, stories and photo reports.

Motoroblocks used in almost every compound belong to seasonal mechanisms. Spring plowing and sowing, summer processing of crops, autumn - harvesting suffer. In winter, these beneficial devices are idle, losing economic efficiency.

1 Principle of operation of the screw mechanism
2 Snowplow with your own hands - Types of designs
3 How to make a screw snow blower do it yourself?
4 power plant for auger snow blower
5 Snow blower from chainsaws
6 Electric snow blower do it yourself

But it is enough to make another fixture to the motoblock, and you will get a homemade snowplow.

Almost throughout Russia, snow cleaning becomes a mandatory procedure outside of large cities. To mechanize this process with small financial costs, we will tell you how to build a snow blower with your own hands.

The principle of the screw mechanism

To make the right snow blower, drawings or at least sketches are required.

Before starting the development of your own project, it is necessary to understand the construction of a snow removal mechanism. The camera in which the augers are installed, the lower cut is moving along the solid soil, picking up snow into its cavity as a bulldozer knife.

Inside the rotary screw construction is installed, which moves the snow towards the outlet. This part of the design can be both in the middle and from one side of the chamber. If the capture width is 1 m and more - it is advisable to perform the receiving hole in the middle to load the rotor evenly.

In addition to spirally located aunts, the rotor is equipped with sweeping blades, with which snow falls into the receiving hole. Next, the mechanism energizes the snow through the socket in the right direction, or immersing it in the body going alongside the transport.

Snowplow do it yourself - types of designs

The main difference between the screw snow blowers, not by the method of collecting snow, but if possible movement.

Passive structures. The mechanism of this type, the operator moves independently, the power plant drives only the rotor itself. Such a design is easy to manufacture, but you will have to make considerable efforts when cleaning snow, especially if the cover is high and dense.

The snowplow is equipped with a light low-power engine, for example, from chainsaws. Or you can adjust the electromotor if the cleaning area is located near the connection point to the electricity.

Sometimes there is such a snow blower on the fiberboard. Only you will need a power take-off shaft to drive a screw mechanism. Then self-propellability ensures the motor-block itself, and part of the power goes to the drive for snow cleaning;

Self-propelled structures. The homemade snow blower of this type is initially designed as capable of moving independently. Either the drive of the leading wheels is installed on the frame, or the engine is integrated into the design with its own wheels.

Create such a project is more complicated, but it pays off ease of use and smaller forces that you spend when cleaning snow;

There are still snow retarders of the unscrewing type. It is only necessary to make a semicircular sequence. However, this design has serious shortcomings.

First, for such a cleaner, a very powerful motor is required, because during the work, a large resistance of snow acts onto it.

Secondly, the quality of cleaning leaves much to be desired. On the edge of the cleared road remains dense drills that are harder than virgin snow.

At the same time, the screw cleaner evenly scatters an explosive snow on a large area, without creating a dense coup.

How to make a screw snow blower do it yourself?

First of all, we make a snow removal chamber in which a rotary screw will work. It must be a barrel-shaped form, with a receiving sector at least 120 °.

It can be made from sheet steel with a thickness of 2 mm, or from aluminum sheets 3 mm thick. Perfectly suitable corrugated aluminum used for equipment of SUVs. It is tougher, due to the molded pattern.

The most economical option is a galvanized iron sheet. Given the low strength, the sidewalls are better made of plywood or textolite.

Now about the most responsible part of the mechanism - about screws. They can be welded from sheet steel (or aluminum), and you can cut out of dense rubber, from the old conveyor used on the granaries or in the oreton. If you can ask for old tires on the tire terminal - excellent shnek blades are obtained from the sidewall.

The manufacture of the rotor from the steel sheet requires accuracy and thorough markup. Moreover, one hundred spiral should be carved absolutely symmetrically, the rotation step must be kept over the entire length of the structure. The welding of segments is performed using conductors that can be made from a pair of vice.

Purchase blades are made of thicker metal, since they have a load of the rumble of already rammed snow.
As a result, this design should turn out.

Important! When developing a rotary screw, do not confuse the direction of rotation and synchronize it with popping blades. The correctly assembled mechanism allows you to do without an additional rotor in the output tube. The screw strength will be enough to make the homemade snow blower discarded the snow at a sufficient distance.

The finished auger can be adapted to the fiberboard, install on the wheels and move it yourself. Or even consolidate on the frame ahead of the SUV or pickup. The main thing is to ensure the result of the torque to the working shaft.

Power supply for auger snow blower

If you decide to assemble a snow blower with your own hands on the basis of the motoblock - the design of the drive is on the surface. If there is a power take-off shaft, you just output the cardan, chain or belt transmission to the shaft of the auger, and invent the clutch mechanism. There is no need to rotate the shaft in good.

If your motoblock is equipped with only a gearbox - you will need to remove the belt or chain drive to a century from the drive axis. The gear ratio of pulleys or chain sprockets pick up the increase in revolutions.

The auger works more efficiently at high speed, the worm principle acts only on very dense snow. That is, the shaft of the screw should rotate 2-3 times faster than the shaft of the wheels.

If there is an additional rotary emission mechanism on the output tube - its speed should be even higher, since the volume of snow in the center of the screw is maximum, and it must be thrown out of the chamber as soon as possible.

Snowboard from chainsaws

If there is no need to remove access paths to the house and the garage, the snow blower may be light and compact. The width of the workspace is no more than 50 cm. This design is not necessarily done self-propelled, and the engine is not needed that is not so powerful. For example, from chainsaws.

Camera with Schneck make the same way as in the previous version. Only materials and sizes choose the appropriate. A screw for one turn in each wing of the chamber, the secondary rotor on the output pipe is not needed.

It can move such a snow blower on improvised classes installed on the edges of the camera. Instead of a bar, a chain drive to the rotor is served from chainsaws. The leading asterisk remains the same.

An additional clutch mechanism is not required, a regular friction chainsaw copes with this task perfectly.

The only thing to take care of - about the ravings. Since the engine from chainsaw is attached on the one hand (it is impossible to do this in the center, the feed blades are interfered), the control knob must be shifted from the center towards the motor mounting. Then it will work more convenient.

The output tube is made of plastic water water. Diameter 120-150 mm is quite enough for such a volume of snow.

Such a compact snow blower will pull the track in your yard in a few minutes, and there is not much time on its manufacture. And the summer of chainsaw is dismantled with a screw and is used for its intended purpose.

All the details and secrets of the home-made snow blower from chainsaws in this video. Do not even need a drawing, everything is clearly and detailed and explained.

Electric snowplow do it yourself

If there is a conditionally free electric motor with a capacity of 1-3 kW, you can create a productive snow removal machine on its database.

Important! The economy in this design works only when the length of the supply wire does not exceed 30 m. Given the aggressive operating conditions, the wire must be high quality, and therefore, expensive in terms of cost. The usual extension driver is not suitable.

Given the constructive feature of the electric motor, the cleaning mechanism can be performed not to screw, but rotary. Working nozzle dresses directly on the engine shaft, high speed.

You can use the "snail" from the ventilation system as a working chamber. The existing slurry is great for snow ejection. The installation size allows you to move it manually.
No matter what the design of your snowplow is the main thing that you saved on her purchase.

Sigor weather conditions in Russia forcing owners of country sites or private sectors acquire snow removal machines. Strong blizzards, meters and more heights of the drifts, all this brings great inconvenience to transport and pedestrians. To eliminate similar problems, many homemade masters make a snow blower with their own hands from the priests. Thus, their assortment appears a reliable and economy unit.

Varieties of technology

There are many different snow blowers on the market. All variations are divided into several types of work method. Since rotary variations are the most popular, consider three classes of this category:

The cunning machine is used to clean the small area from fresh and blind snow. This technique is able to cast a lot on the sides or collect in a snowswicker. The screw cleaner made with their own hands has a simple scheme that takes into account the presence of auction.

Construction of a screw-fan unit

Plumba rotary unit is most suitable for cleaning fresh snow. The homemade device is placed on a minitractor, a mini loader or chassis and is equipped with a plow with a 1-2 rotor.
The milling and rotary harvesting machine has the opportunity identical to the first option. This is a powerful snow blower with parameters that allow you to overcome three-meter drifts and cast a snowy mass to a distance of up to 20 m.

Before making a snow removal machine, it is necessary to know that the views under consideration are equipped with feeder mills and a rotor-throtter. This is an important aspect that needs to be taken into account when designing a construction drawing.

How the snow blower is arranged

The diagram of each self-made snow blower includes a number of nodes and mechanisms. The number of components of self-propelled devices includes:

Power unit. A snow blower made of chainsaw friendship, a powerful trimmer, a gas station or another device, where there is a gasoline or electric type engine with a high torque indicator.
Chassis. Before making the snow removal machine, it is necessary to determine the chassis, it will consist of wheels or caterpillars.
Casing. This item is located in the nose area of \u200b\u200bthe equipment. For its manufacture, as a rule, we use durable plastics or metal. In the inside, there is a functioning organ of the snowpressure, for example a special plow or auger.
Snowmanship. This item is responsible directly for the collection of snow, various working items can be used in models - plow, auger, cutter.

Graduation chute. There is a plastic or metal type. When the apparatus is working on it, it will circulate a snow amount directly to the emission area.
Handles. Using the handles, the operator will be able to control the technique or change the modes.
Rotor. It is used only in rotary snow blowers with their own hands, as a whole looks like a roller with a multitude of blades.

How to make a snow blower from chainsaws? Easy, if you follow the steps and fulfill all the recommendations. For homemade snow removal machines for home, it is necessary not all the chainsaw of the Urals, but only its engine.

What you need for a snow blower from chainsaws with your own hands:

roofing iron;
plywood sheet 1 cm;
metal nozzles ½ inches, ¾;
metal corners;
plastic pipe for 16 cm;
conveyor belt 1 cm thick;
closed self-centered bearings 205.

Stages of creating a home-made snowfatheboard from chainsaws are as follows:

First of all, it is necessary to figure out how to make a screw body for snow cleaner. For this, it is used roofing iron. Side parties are performed from plywood. Cook the frame from metal robust corners for prepared drawings. From the pipe to ½ inches, prepare a handle, and from ¾ - the shaft of the auger.

Drawing of chainsaw

In the midst of the blade for garbage of the snow mass, you need to make a through hole so that it can be attached to the pipe. For a 2-axis auger, it is necessary to prepare 4 rings from the conveyor belt with a size of 28 cm.
Metal angle Fix on the nozzle in the T-shaped position relative to the plate. This is necessary to install the rapid filamental unit platform. So that the shaft is freely immersed in the bearings, it is required on the edges to equip two cuts. Also, on one side of the shaft, you need to create a groove to install the key under the star.
As a hodovka, it is recommended to use skis, painted from wood bars. Such a running part will be much better to manifest itself in operation than the wheelbase. To ski for the harvesting machine with their own hands, they slid well through the snow, equip them with plastic linings from the wiring box.
For the manufacture of swivel chute, use plastic pipes. The pipe with a smaller diameter is fixed on the element with a large one, while the narrower tube is joined to the auger frame. To the finished turning groove, lock the cut part from the sewer pipe. She, when working homemade cleaner, will set the direction where the snow mass should be discarded.

In order for the volume of snow unhindered circulating through the system to exit, the size of the screw blade should be less than the diameter of the chute itself. Otherwise, the technique will regularly be clogged.

The length of the gutter affects the direction of snow garbage and its flight range. This should be taken into account when determining the size.

The final stage of creating a snow removal machine with their hands from chainsaws is the processing of the design of the anti-corrosion agent and the coating of the paintwork.

Video: Device of a homemade snow blower from the "Ural" chainsaw

Scheme and assembly of auger unit

Auger is a mandatory element of any snow removal technique. Constructively, this is a drum with rotating spirals with twisted legs. At the base of the spiral there are metal blades, which, when rotating, shrink snow from the sides to the center, after which they pushed the mass through the nozzle.

In order to make a screw with their own hands, the shaft will be needed - it is made by a metal pipe with a diameter. The length is determined by which the grip area is planned. On average, it is from half a meter to 80 cm. Less - inefficient, more - the technique will be hard to move.

Two steel plates of rectangular shape weld to the pipe center - this is future design blades. The legs can be made of steel, sidewalls used tires or conveyor belt. Next, cut from the sheet metal 4 disk with a diameter of 28 cm and cut the circle in the center of the shaft diameter. Rings are cut on one side and neatly stretching on the sides - these are spiral coils, which, as indicated in the diagram, weld to the shaft towards the shovels.

It is important to withstand the same distance between the coils of the spiral, otherwise the snow blower will vive on the sides.

At the edges of the shaft, the troughs are welded to which closed-type bearings No. 305 are put on. It is necessary in order for the drum during harvesting does not jarny stone.

For the bucket, there will be a sheet of 2 mm of the same length as auger + along the edges of 2-3 cm. Woven it down the spiral so that the radius was 2 cm larger than the diameter of the knives. The side walls are better made by metal, but thick plywood is suitable. In the center of the hubs insert and put the screw made. Pre-onto the pin with a pulley of the belt drive. At the top of the bucket you need to make a semblance of a sleeve with a visor to direct the snow out in the desired side.

Now it has been a queue of connecting an electric motor, for which they are prepared for the frame with dimensions of 48x70 cm and 50 cm wide with jumpers for installation of the engine.

At the bottom edge of the frame, the frame is screwed down (2 corners are pre-cut and edges bend). Now it remains to install the engine, make pulley and connect the cable.

Before the first launch hands, scroll the auger, check that he moved freely. If there are no obstacles, you can start cleaning.

Video: alteration of trimmer in a snow blower

Now the small household equipment market offers a large number of snow blowers, both in the form of attachments to motor-blocks and in the form of a fully separate mechanism equipped with a power installation.

If you look good for anyone, there is nothing difficult there, which means it can be made and yourself, having only the necessary materials and tools on the farm. Equipment will also be needed. Many craftsmen were able to adapt the engine from Soviet chainsaws "Ural" as a propeller for homemade cleaner.

Advantages and disadvantages

A couple of positive moments a homemade snow blower made from the "Ural" chainsaw:

The cost of making such an aggregate will be made at times cheaper than the acquisition of a plant model of a snow blower, even if you have to buy a used chainsaw;
The performance of the snow blower with the engine from the "Ural" chainsaw will not particularly give way to this indicator of the factory model;
Almost all other snow retarder elements are made of submitted materials - segments of pipes, sheets and segments of thin iron.

The main disadvantage that the homemade snow blower on the basis of chainsaw has, and because of which it is inferior to factory models, and not everyone is the lack of a mechanism that ensures self-propelled movement of this snow blower, it has to push it in front of him that is not particularly easy.

But in general, the homemade aggregate is worthy of attention, because it can significantly save money and facilitate the cleaning of snow.
Photo of the homemade snow blower from the chainsaw of the Ural

Rama, power plant

Welding the frame is better made of pipes of small diameter. Segments of pipes that will be located longitudinally relative to the aggregate itself, will also be also by clauses, with the help of them the snow blower will move through the snow. Therefore, the edges of these segments that will be ahead better to cut at an angle, and the holes are brewing so that the snow is not stuffed into the pipes.

Of the two segments of pipes that will be located longitudinally, and two segments located transversely welded the frame. In this case, in this case are needed to fix the engine on them, so one should be located on the rear edge of longitudinal segments, and the second cross is about 200 mm from the first.

The distance between the longitudinal segments should not exceed 700 mm. That is, the frame is formed in the form of the letter P, but with two crossings.

The power plant is used from Soviet chainsaws because the torque does not have much large, but a good traction force. All chainsaws do not need, so you need to remove the motor with a frame. Next, it needs to remake a little. Chainsaw chain drive sprockets need to install a driving small sprocket from the "Sunrise" motorcycle, Minsk. You can simply welcome it to the star of chainsaws, pre-centering it.
Stock Foto Finished power plant

Auger, auger case, drive

Go to the working bodies of the Ural snow blower, namely to the screw. It is made of a cut of a small diameter pipe. You can also use any shafts long to 80-850 mm. An important condition is the selection of bearings for the shaft. Such a shaft length is needed to provide a drive to it, which will be located outside the hull.

Next of the sheet metal with a thickness of 2-3 mm, you need to cut 4 circles with an outer diameter of 300 mm. In these circles, holes with a diameter of 220-230 mm are cut. Next, the existing discs are cut on one side and the disk is stretched at the cut place, forming the similarity of the springs. It is necessary to do this with all 4 blanks.

Then you need to calculate the center of the shaft, taking into account the segment it, which will be used under the drive. In the center of the shaft to it, it will be necessary to weld two plates with a long 130 mm and a width of 150 mm. They should be parallel to each other. These plates will be blades for snow ejection.

The harvested screw ribbons are welded on one side to the blades, on the other hand, the struts are attached to the shaft, to which other ends of the ribbons are welded. It is necessary to arrange the ribbons so that their turns on the movement are sent to the center. That is, on both sides of the blades, two ribbons must be located, installed in parallel and their turns sent to the center. Moreover, the whole structure in length should not exceed 700 mm in length, the rest of the shaft will move away under the drive.

Photo of the screw mechanism of the homemade snow blower

Go to the case. It is made from round sidewalls, which in diameter must exceed the auger by about 50-70 mm. Next, the metal sheet is taken with a thickness of 1-1.5 mm. It is bent around the sidewall circumference, and welded to them, forming a semicircle. In the sidewalls in the center there are holes in which the finished auger is inserted. On the outside, the sidewalls on the shaft are dressed up bearings, pressed to the sidewalls and fixed, while the fault position is centered. To secure bearings to the sidewalls, you can make clips, or simply weld them to the sidewalls by external clips, but then the design will be inseparable.

Next you need to make a snowstone. It is possible to make it from the segment of an aluminum pipe with a diameter of 150 mm and a length of 100 mm, as well as sheet metal segments of which will need to form a box. The cut of the pipe will be the basis of a snowdow. To install it, the hole is done in the casing of the screw, it is necessary to diameter, located so that it is a little rear from the shnek blades. Inserts a cut of the pipe into the hole and fixes in it with a bolted connection, and the prepared box is connected to the pipe.

On the segment of the shaft, the driven by the rear asterisk from the specified motorcycles is put on and is fixed on it using welding.

It remains only to collect together the design. The hull together with the screw is placed on the longitudinal elements of the frame and welded in it. The strength installation is fixed on the crossbar, but so that the leading and led sprockets were located in the same plane. A motorcycle chain will be used for the drive. Its tension is fashionable to implement in two ways: tension by moving the power plant, but for this you need to provide the possibility of longitudinal movement of the motor with the possibility of securing it at any point. You can also implement a tensioned asterisk with a bolted fastening to the auger housing.

It remains only for the frame to attach the control knob made of both pipes, and to display the throttle control of the engine on the handle.

Before testing a snow blower, you need to believe all the connections and make sure that the auger rotates easily and does not cling to the elements of the case.
Video overview of the homemade snow blower from the "Ural" chainsaw: