How to install a ribbon clamp on a cover cover. How to tighten the clamp on the shrussa. How to clamp a clamp on a short - mechanical method

14 Days Ago.

This, probably, in the mentality of a Russian person - to delay the clamps so that the hose squeezes out from under him, to make two turns of the ribbon clamp on a shrussi busty, when it is quite enough and one, if you press a button, so that it grind, twist the nuts The bolts on the wheels - be sure to jump on the clergy, and suddenly turn off on the road! And so everywhere. Permanent relocation. I think it's all from stupidity. Yes, it is from her. And from inability to think logically. A logically thoughtful person, as well as a person who seems, will see that the shaft and on the "grenade" there are ring grooves, in which the edges of the correctly selected anther clearly get the edges. That is, the boot sits on a grenade and the shaft without any clamp and if not exposing this boot to mechanical effects, then the lubricant will never leak out without a clamp.
For those who still do not understand: the claw on the flesh is only to support the anther, that is, this clamp should not be delayed strongly, it must be tightened enough, so that only he started to premine the rubber. And horseradish boot when jumping and fucking from under him that will be squeezed when. The boot is held by the groove. And compacted the most elasticity of rubber. The clamp is needed, repeating, only for support, so as not to give the anticon to jump from the groove with a random mechanical exposure.
So there are pliers, screwdriver. One turnover of the clamp is done. We rest in a screwdriver, pliers stretch the clamp with an effort of a weak granny, bend, cut up too much, leave the tail at 0.3 cm so that it does not catch it, then the punch with a hammer on it, and everyone. No filigree crafts for the tail is not needed, under the mustache it is also superfluous. These are enough of these very minimal 0.3 cm and the hammer impact. The clamp is obtained as if one piece, nothing sticks out, therefore, there is nothing to catch.
And also: anthers need to wear on a dry shaft, without lubricant. That is, under the rubber must be dry. These are your problems, how to fill the shrus to not smear the seating of the anther, but they should be clean.

To transmit the torque of the motor from the gearbox to the drive wheels without power loss, the hinge is used by the hinge of equal angular velocities (or shrus). This item is used both on rear-wheel drive machines and on a car with front-wheel drive. She creates clamps. About how to properly tighten the clamp on a shrus, this article will tell.

Why fasten the clamp on a shrus

Sls - a reliable mechanism that can easily drive more than 150,000 km, but over time he comes into disrepair. There is an unpleasant crunch about problems with the detail. Crunch can not only used, but also completely new cars. The ability of the hinge faith and truth to serve for a long time depends on 2 conditions:

full-fledged lubrication;
protection against the negative effect of the medium (pollution or water entering).

The hinge must be lubricated - and the more often the better. And it is protected with the help of an anther, which is put on the shaft and reliably covers the elements of the node. Blank crepe clamps. When their weakening occurs, an unpleasant sound is heard. Therefore, from time to time the driver faces such a task as a tightening of the craftsmanship of the shrussa.

There are several ways to fasten a scruck:

ribbon mechanism;
clamping fasteners;
P-shaped mounting option.

How to tighten the ribbon clamp on a shurt - manual way

It is easy to install such a fixture, and its fixation is quite reliable. When choosing a device, see the quality of the steel, from which it is manufactured. To fasten it, you will have to use a device for tightening tape clamps. To tighten the device, you can apply pliers.

We act like this:

The chomotic is planted on the boot, his tip is capturing the passage.
Next, tint on yourself, applying efforts. During the procedure, watches so that the tightening happened without distortion.
We start the tip the tip and bend the mustache.
The end of the tape is fastened. At the end of the installation, check the uniformity of the fit.

But how to properly carry out the procedure using a tightening machine:

Ribbon placing from the top of the anther. Her tip insert into the holder (for this there is a propyl).
The holder is pressed to the castle of the clamp.
Tape on the tool we wake up rotational movements. When the stretch is normal, ribbon bend.
Perform installation installation. Take the power of tension. After tensioning, the lubricant should not go out. If you drag, the boot is bursting.

How to clamp a clamp on a short - mechanical method

Some cars from Europe are transferred to the use of clamps made in the form of clamps. Clamps are characterized by simplicity and durability. They usually establish them with ticks, but folk craftsmen are capable of ordinary pliers.

Before installing the clamp, select the diameter. After that, the installation of clamps on the boot shrus is made. It is important to do without distortion. Installation is better done with crimping forceps. With their absence, we use ticks. The work is simple, at its end it is necessary to check the quality of the clamp. The main advantage of the option - no need to use special tools. If when installing the device, use conventional pliers, the quality of the clamp does not suffer from this.

You can use a screw type device. It is clamped using a screwdriver. Install such a chomotic is the easiest way, but there are no drawbacks here:

"Pomegranate" (Jargon Name) is exposed to vibration, due to which the bolt can unscrew. Therefore, delaying the device needs as stronger as possible.
The protrusion lock looks inetetic. In addition, when driving, he may hurt for anything.
Such clamps are often poor-quality.

How to Tighten the Claw Claw Clause P-shaped

Now the covers began to make out of a more rigid material than ordinary rubber. They are not easy to tighten with ordinary ribbon homutics. Therefore, many motorists prefer upgraded devices. There are different variants among inexpensive - fastening with P-shaped ears. They are tightened with tongs, most often the Licota ATC-2190 brand.

There are such ticks are expensive - up to 20 euros, but there are cheaper options. It is better to use ticks with a cut under the square 1/2. The knobs on them can be lengthened using gates. The principle of operation of the device is simple: it squeezes the P-shaped tubercle on the chomant, and the fastener is well delayed. Tools with elongated handles are especially effective. They are well compressed even covers made of dense material.

The installation of the clamp avoids the leakage of the label. During operation, the clip clamp can relax and the garbage caught under the boot in a shorter will increase the crunch and the need to repair the hinge, so at the very first sections of lubrication, measures preventing depressurization should be taken.

Plastic and Wire Clamps

Plastic clamps are not used for fixing the anther. It is due to the low strength and reliability of the attachment. Such a clamp is not able to withstand dynamic loads, and also inclined to the appearance of damage from high and low temperatures.

Properly supplied wire clamp does not differ at the strength of fixation from the factory. Despite this, it is not recommended to use it for the following reasons:

too strong tightening leads to the conquest of the anther;
the wire may not be sufficiently tough, which will lead to the shooting of the attachment;
lack of strength causes a rupture of the wire during operation.

Unlike plastic, with their own hands, the clamp from the wire can serve as a temporary replacement of the original. At the first opportunity, replace this attachment to more reliable.

Ribbon metal clamps

Most often, this type of fasteners goes in the factory configuration. Conducted by reliable fixation and simplicity of installation. In order for the shrus clamp to be operated for a long time, it is necessary to fulfill the following conditions:

manufacturing tape, the manufacturer used high-quality steel;
mounting on the boot was performed using a device for tightening tape clamps of a shruss;
to install fasteners, you need to have a skill skills with a tool.

For a tightening of the shrussh clamps, you can use undergraduate tools, but quality will depend only on the experience of Cleretz. The only tool that will be required - pliers. Clamp tightening sequence:

The clamp is satisfied with the boot;
The tip is captured by pliers;
Pull with a little effort and trace so that the claw tighten the boot without distortion;
Create a maximum effort and adjust up;
Beat the mustache;
Fasten the end of the tape.

Upon completion of the installation on the hinge of equal angular velocities, it is required to monitor the uniform of the fit of the clamp and the absence of distortion.

Use special devices when installing a ribbon clamp

To simplify tape tape and improving the quality of the anther fixing, a special tightening machine is used. It includes:

a pen;
holder;
turntable.

To use the device, you should follow the plan:

Locate the tape on top of the anther;
Insert her end into the cut holder;
Superflow the holder in the castle of the Khomut;
Rotational movements to start winding the tape to the tool;
With sufficient tension, bend the tape;
Control the stipped clamp on the correct installation.

To carry out high-quality installation, the final effort should be determined correctly. The power of the tightening should not allow lubrication to get out of the outside, but at the same time should not allow the dust.

Clamp fastener

Part of the European-made cars is translated into the use of clamping clamps, as they combine reliability and simplicity. For their installation, special pings are used for a shruss clamp.

Performing the placement of the chomut on the Sls takes place in the following order:

The necessary diameter is selected;
The clamp is located on the protein. It should be installed without distortion;
To implement crimping, use forceps for clamps. In the case of their absence, you can use the tick of the appropriate size;
Upon completion of work, you should check the reliability of the fixation of the clamp.

The main advantage of the clamping fastener is the lack of the need to buy an expensive special tool. Performing work with conventional ticks will ensure high reliability and long service.

Alternative options

Create a shrus anther coat with a screw clamp. You can use the key or a screwdriver for tightening. It practically does not require skills for their fixation, but has a number of shortcomings, which does not allow to take a niche of the clamps for the shrusov:

A temporary alternative to the Sls may be a helical column with a key. Its installation can be made on road conditions to ensure the lack of lubrication contamination when traveling to a hundred.

Choosing between the ribbon and clamping clamp should be guided by its preferences and manufacturer's recommendations. They both are capable of listening for a long time with proper installation. Attentiveness and accuracy during installation of any of the fasteners will allow a long lubricant for a long time.

Claw Claw Claws, Pliers, Tongs and Other Fixtures and Tools for Installation, Crimp and Tightening Tape and Plastic Species

If you have any questions - leave them in the comments under the article. We or our visitors will gladly respond to them