Pack the inflatable mattress. How to make a hole in an inflatable mattress: Top, irrigate, turn out other home repair trips. Preparation of the surface and patchwork

Inflatable mattress - the thing is rather durable, and by itself he is unlikely to start passing the air. The most common reason, because of which the product fails is the sharp feline claws. But is it worth saying goodbye to your favorite cat because of this? Moreover, a spoiled thing can be easily repaired, if you know how to make an inflatable mattress.

How to find puncture

Is it possible to flick the inflatable mattress yourself? Of course.

To do this, you will need:

pump;
marker;
water container (for the first method);
sponge and any foaming agent (for the second);
flour or starch (for the third method);
match or lighter (for the fourth).

1st Method: Perching

A reliable way to find a damaged place before taking an inflatable mattress at home, - immerse it into the water. If the mattress is completely small, enough and bowls for 10 - 20 liters, the subject will have to put in the bath, well, and the "adult" full mattress will fit only in the summer pool or a small pond.

The product in which you want to find a hole is pumped into the pump and placed in water container. Next, carefully observe: air bubbles will be visible at the point of puncture.

To detect a defect there is no point in throwing a thing into the river or another reservoir with a constant flow, because small air bubbles in such water can hardly discern.

Having found a hole, it is immediately marked with a marker. But you should not hurry and immediately remove the product from the water. Perhaps the puncture is not alone and there are tiny holes, because of which the mattress renovated in the most thorough way will still have air.

2nd Method: Washed

If the product is large, there is no pond or pool, you can find a puncture, because of which it desces the air mattress, with the help of foam.

To do this, take any means for washing or washing and whipped in foam. The foam sponge is applied to the resulting foam on the entire surface and fixed, in which air bubbles appear. On the thick foam they will be easy to detect.

And if there are no bubbles? Then the puncture is on the other side, and it will have to repeat the procedure to repeat first.

3rd Method: Swipping

In addition to the wet methods described above, there is dry. It is used before taking an inflatable mattress from the velor side.

The soap solution on such a surface is foaming very badly, besides, wet furniture, albeit inflatable, is not the most pleasant thing in the house. Therefore, a completely dry mattress is twisted with starch, flour, hammer mustard or other powdered means. At the point of puncture, the lightweight powder will be blown away by air coming out of the hole.

After all the punctures are detected, the purified flour from the surface is collected by a vacuum cleaner.

4th Method: Fire Test

How to find a puncture in an inflatable mattress in this way? Very simple. All you need is matches or lighter. You need to carefully follow the flame: in the place of the puncture it will be slightly blewing the air coming out of the cutters.

5th Method: Pets

There is another proven way to find a puncture. If you have a cat or a cat in the house, then after you punish the mattress, they will definitely find a hole from which air blows. And this will happen for several reasons:

Good hearing. A weak sound outgoing from the hole of the mattress is well heard for them.
Curiosity. Due to it, pets are proceeding.
Playfulness. After the find, they begin to play with a thin "trickle" air.

This method is not fiction and happened this more than once.

How to stack

Making sure that all damage is detected, you can be taken for repairing an inflatable mattress with your own hands. To do this, the puncture impose a pay or a special sticker.

Party 1.

Before taking a hole in an inflatable mattress with a smooth side, prepare:

glue;
patch;
small sandpaper (skirt);
scissors;
degreased fluid (solvent).

A marker marker is cleaned with a skin and degreased by a solvent.

Cut the patch of the desired size, better without sharp angles, oval or round form. Mold must be more cut at least 3 centimeters on each side.

For repairing a smooth side, a transparent vinyl film is used.

After gluing, the product does not use another day or two until the seam acquires the necessary strength. Preferably, the place of gluing is pressed by something heavy.

In no case cannot be used to repair an inflatable mattress from PVC super-glue. The alpha-cyanacrylic acid contained in it will permanently ruin the vinyl, and the thing will have to be easy to throw.

Side 2 (velor)

If the defect was formed on the side with a flash coating, a soft pile ("velor") carefully cleaned with a skin or washed off with alcohol, otherwise the patch will not stick. Then act in the same way as when repairing a smooth side. Only the patch is used special - from FLOK.

Unfortunately, stick such a pay imperceptibly, it will not work. In order not to do on velor's beds, you can try to stick the product from the inside. To do this, helping its own ruler, pull up a defective area to a wide hole used for inflation. Printed in a patch and wait 12 hours. After that, the product can be turned back.

Plus this method is that the product can be repaired almost unnoticed. And, in addition, the patch holds especially hard because the air presses from the inside.

Finally, the most difficult question: how to make an inflatable mattress by seam. This is the worst damage option. It is unlikely that in this case it will be possible to repair the thing at home qualitatively. It is better to know where the workshop on the repair of inflatable mattresses and turn to professionals. After all, they possess not only experience, but also special equipment.

If they still repair independently, the mattress turns, the place of damage is degreased with alcohol and fasten the pay.

Advantages of glue Intex

Often asked what glue to stick an inflatable mattress from PVC? By and large, any suitable for gluing rubber or PVC products. You can use DESMOCOLL (desmocol) - glue for the repair of inflatable mattresses, which is based on natural rubber.

The reliability of the connection will increase significantly if you act according to a specific technology. For this, desmocol is applied to the glued parts, wait, when the glue dries, after which the dried layer is heated by a hot hair dryer and both parts are pressed.

But it is logical to assume that the best adhesive for Intex mattresses is one that is produced under the same name, that is, the company's branded glue. The set for repair includes patches of several species and glue itself.

Those who have already tried the glue Intex in the case, argue that he is reliably glue not only mattresses, but even inflated pools. Patch holds for several seasons.

An inflatable mattress can be successfully used as a bed, and as a floating. And so that he serve for a long time, you need to perform only two conditions - dry well before storage and take care of acute items.

Do not hesitate to inflate it. To "not rearrange", it is better not to use powerful car pumps and compressors for this.

Release the air gradually. If you strongly press the surface to speed up the process, you can damage the seams.

They clean such products with a solution of neutral soap or shampoo. The less chemistry - the better. Abrasive powders are also better not to apply.

In the case of a cut or gap, of course, it is possible to make a mattress yourself, but if there is a large damage (more centimeter), it is better to turn to a specialized workshop to repair it. The help of professionals will be needed in the event that the mattress suffered from dog teeth or claws.

The master not only repairs the breaks of the gaps, but will completely replace damaged parts if there is a need for this.

Amazon.com.

Inflate the mattress, remove all the sources of noise and listen carefully. Damage in the mattress can issue yourself with a light whistling sound. For loyalty, the noisy part can be immersed in water: small bubbles will indicate the location of the puncture.

If the previous way does not help, it's time to feel like a real brand. In the containers, we whip the water with a detergent and the tassel applied a thick soap foam to the surface of the mattress. In places of puncture, the foam will begin to bubble.

After you have found damage, circle it with a handle or shallow, so as not to lose.

2. Prepare the surface

Matrasguru.ru.

Before starting all the air from the mattress. Place around the puncture Clean from dust and dirt, degrease the surface with gasoline or alcohol. If you need to make a coating mattress from velor or flock, it is important to remove the vehicle with acetone or fine-grained sandpaper before overlaying the patch.

3. Prepare a patch

Allegrimg.com.

Sometimes complete with the mattress go special sets for repair. If there is no such, take pieces of fine rubber from a set for car chamber repair or cut a children's rubber toy. The patch must correspond to the size of the puncture with the deposits of 2-3 cm and be oval or round. Before use, degrease its surface with gasoline or alcohol.

4. Clamp an inflatable mattress

WLOOKS.RU.

How to put a hole in the mattress? It is suitable for PVC glue, a universal "moment" or polyurethane shoe glue.

How to do it? We already have a ready-to-repair mattress and carved skimmed patch. Now apply glue to the mattress and the patch, wait 5 minutes so that the adhesive slightly grabbed, and align them. For a larger effect in place of gluing, you can put a cargo per day.

What to do if you need to take a seam mattress

If the mattress broke through the seam, the patch, imposed on the outer side, may not help. In this case, it makes sense to take the mattress from the inside. For this, hand or ruler stretch the damaged area through the valve hole. Then glue the patch (according to the instructions from the previous item) to the inside of the mattress. Remove the mattress and use it as usual can already be afraid after a complete drying of the glue.

How to avoid new damage

In order for the fixed inflatable mattress to please you as long as possible, follow the next unaccompanious rules.

Before putting the mattress on the floor, grass or sand, inspect the surface for the presence of stitching items.
Do not play on pet mattress: they can pierce it with claws or teeth.
Do not pull the mattress by the floor if people lie on it: the seams can disperse.

Inflatable furniture is popular in mind its convenience, ease of storage and transportation. But over time, the holes appear on the mattresses that air leaves.

You can eliminate damage on your own at home. Most often damage is associated with the inflammation of the mattress to the maximum. Manufacturers indicate the instructions that it is prohibited, but many violate this rule.

Rubber glue made of natural rubber desmocol.
Super moment Crystal from Henkel.
Uranus for rubber boats.

Do not forget that toxins included in the adhesive substances can harm the person and require careful and careful circulation.

It is worth remembering that the compositions for working with inflatable products are flammable and near you should not be open sources of fire or sparks.

How to make an intex inflatable mattress

You will need:

scissors,
glue,
rubber patch,
glue brush
sandpaper,
detergent or shaving foam.

VIDEO INSTRUCTION

You need to start with the search for damaged places, it is not easy. Usually holes leave pets or children who love to jump from the heart.

First of all, it is worth considering the seams, the joints of the surface and inland ribs.

Not in domestic conditions use the way: omit the inflated mattress into the water and look where air bubbles will go.
At home, you can use soap or shave foam by applying it to possible points of punctures, in the air outlet areas it will be bubble.
If you failed to find cuts, the mattress pour water with detergent liquid. From damaged places with pressing on the mattress, soap water will go out with a whistle.
When damage is found, a pin or sticker is applied to the cut.
What glue to fuck an inflatable mattressThe masters respond - to buy intended for the repair of inflatable things, the set of Intex company, includes materials for patches, and glue.

If a cut on the joints of the seams, the place is treated with alcohol, and then glued according to the instructions.

But in order not to spoil the appearance, glue can be applied from the inside.

The damaged area is pulled out through the valve hole and fasten the patch from the inside.
The glue takes a bit - apply a smooth layer on the patch and firmly pressed to the surface. Leave the mattress to dry at about 12 hours.

Phased by putting the mattress

Another option for the reconstruction of the mattress:

Place of damage is treated with sandpaper.
Then impregnate with alcohol.
After that, pick up the size of the patch, apply glue on it and attach to the place of cuts. Instead of purchased patches, rubberized materials and polyurethane glue or the composition for working with rubber can be used.
After gluing patches, the mattresses are left under the press for 24 hours.
Next inflated and check how reliably it was possible to glue the patch and cut.

If there are several damage, they need to be close in stages, waiting until the previous seam will completely grab. If, after inflation, the air leaves anyway, it means that there are still cuts left or the input valve is loosely screwed.

If the problem is in the valve:

To test malfunctions in the valve hole, in the inflated mattress pour the shaving foam.
It will foam around the valve if there are damage in it.
Then the valve is twisted and scattered.
The end itself is grinning and treated with silicone lubricant and return to the place. With serious damage to the valve, you will have to contact the workshop.

Video on the topic

Where to fuck an inflatable mattress

If you have this question, then with big cuts, punctures, separated by the seams better to call and ask for helping professionals.

It is difficult to correct the ruptures of the seams or damage to the internal partitions. The masters can come to your home and eliminate damage in place. And if a small puncture happened, cut, you can correct the problem yourself.

Companies and private masters are working, which specialize in the repair of such products. It is necessary to call professionals if the seams and cuts are more than five cm. And the inner partitions were broken away.

Inflatable mattresses (beds) are comfortable in the case when you need to quickly organize a temporary bed. They are cheap, there are different sizes, shapes and colors. Most modern inflatable mattresses are made of soft leaf polyvinyl chloride (PVC) of a small thickness. The most common problem is air leakage through small damage (holes), which are produced spontaneously in the process of normal operation, simply speaking, the mattress is blown away.

Large companies producers of inflatable mattresses for such cases offer their own repair kits (repair kits) consisting of special glue for PVC and several patches. Such a repair kit can be recommended for the acquisition immediately (together with the mattress), since it is sooner or later, it will be useful.

If there is no corporate repair kit at hand, you can use under your hand.

To make an inflatable mattress need:

Soap water.
Glue "Moment Universal".
Degreaser (acetone or gasoline).
Pieces of fine rubber.

Transparent glue will reduce the flaws of its application.

Included for the repair of automotive chambers you can find ready-made patches of suitable sizes. It was experimentally found that his glue was not suitable for PVC gluing.

The first thing to do is to find all the damage on the mattress, of which the air outwards. To do this, we prepare soap water, we take it up to the formation of abundant foam. Tightly inflatable mattress and start slowly, to consistently apply a foam with a brush for the entire surface. Inflated bubble - evidence of the presence of air leakage. As a rule, the holes are very small, and to not lose sight of them, it is better to immediately bring a problem area with a marker.

Dissolved in the water "foam for baths" allows you to quickly get a lot of foam.

Seating from the mattress air inflates a bubble.

The holes are usually very small, and most often occur in the places of fastening of the internal connectors of the mattress.

On the flocked surface to see the hole even more difficult.

After all the damage is localized, proceed directly to the tiling of the mattress, the air has previously extended from it. Degrease the plotting zone, as well as the pay itself. If the damage is on the upper flocked surface, then the flock must be previously removed using acetone.

Degreasing (photo from above) and removing the flock using acetone.

We apply glue on both surfaces (mattress and patch) with a smooth layer of moderate thickness. Without the five-minute pause, we apply the pay and slightly press it to the place of damage. It makes sense to pushe pay in any cargo for a while up to 24 hours.

Applying glue.

Patch overlay.

After a day, the mattress is tight and with the help of the same soap foam check the quality of the work performed. If the air pokes the air through the pay, it can be careful to tear it off and cross.

As practice shows, putting the inflatable mattresses of different manufacturers more or less regularly, even if you use them neatly, without being reducing without the need. Apparently, the reason for this lies in the inconsistency of the strength characteristics of the material from which the mattresses are manufactured and carrying out operational loads.

It would seem that such a device has solid advantages: and there is where to go to the guests, and in the campaign will allow you to sleep comfortably, and swim on it - one pleasure. And most importantly - in the detour, it takes very little space. But it is easy to damage him, without even noticing it. It is enough to inflate the mattress too much, put on the sun or on the ground in the forest, where the dry grass sticks out. And if he was chosen by her pet - exactly the puncture was not avoided. Blown away antiprolemattress? How to find a hole? How to stick a hole in an inflatable mattress quickly, efficiently and without extra costs?

How to look for a rush

How to find a hole in an inflatable bed or a mattress? First you need to find a hole in an inflatable mattress. Make it with a naked eye difficult. Especially when he is in detour. Inflate the product "to the ring" and check the most frequent locations of damage.

Bottom. Here any hard object on the surface can break through the hole, where we are putting the mattress: a stone, dry grass, a hat from a nail on the floor.
Upper side. Here we can pierce the mattress accessories on clothes, hairpin or earring. Claws of domestic animals is also a frequent reason.
Seams. The mattresses are torn along the seam because they were inflated too much, from sharp landings or children's games with jumps.
Valve. The mechanism can get dust, hair and other trash. Tightness is broken, and the valve begins to pass the air.
Connection locations with partitions. The reason why they are ruting - increase the pressure inside the mattress and the uneven load on the surface. And it happens again again when the product inflated hard or sharply plumbred with all weights. Especially often this "sore" is found in models with partitions-cup holders.
Film. When the mattress is stored for a long time in the folded state, then it is on bending material losing elasticity and a hole may appear.

Carefully inspect each millimeter surface. If there are relatively large damage, then you will easily find them. And to find small punctures, there are the following ways.

Aurally

Tight inflate the mattress.
Create silence as much as possible.
Apply your ear close to the surface and listen. Easy hissing will give the place of puncture.
Explore the whole area of \u200b\u200bthe mattress.
Separately listen to the valve, it can also "strive" air.

You can "feel" a device not only hearing. Apply the cheek or lips to the mattress and feel the air jet from the hole if it is. And you can wet your hand on the elbow and led it close to the surface.

With water

Inflate the mattress.
Lower it under the water. Air bubbles will be released from the cut.
Inspect the product from all sides.

For the absence of open water, you can try to lower the product into a regular bath. But practice shows that even a single mattress does not fully fit into it. And if you immerse in parts, then the middle will still remain unchecked.

Soapy solution

Inflate the product.
Fill with a sponge solution.
Apply foam to the study area. If the hole is - bubbles will be inflated from it.
Treat the entire surface.

For a foam solution, you can use shampoo, liquid soap or dishwashing agents. But not only washing powder - coarse particles scratch the surface and provoke the appearance of new holes.

Shaving foam

Tight inflate the mattress.
Fill under the shaving foam valve.
Bubbles will be published in damage.

Stachmal

Tight inflate the mattress.
Plush the surface with starch. In place of the puncture appear "Cloud".
Treat the whole area in this way.
Swapping the mattress.

This method allows you to find a puncture without water, which reduces the repair time, because the mattress does not need to be dried. Instead of starch, you can point the product with flour, baby powder or any other "volatile" powder.

Food film

Inflate the mattress.
Moisten the surface from the pulverizer.
Cover the piece of food film.
In places of punctures under the film, air will accumulate.

Keep in mind that holes can be a lot. And in order not to lose the place of the puncture, immediately mark it with a pen, pencil or felt-tip pen.

What do you need

Well, if you have a "native" Repair Kit, which goes in a set with a mattress. Not? We will have to use sweater means. To repair a sleeping inflatable mattress, you need to properly choose the glue and the patchwork material.

Glue

It is better to use one of the polyurethane adhesives, they are specifically designed for PVC surfaces:

"Moment Crystal";
Uranus for rubber boats;
glue for shoes, for example, desmocol;
any glue for rubber;
glue from Intex (company producing inflatable pools, boats, mattresses and furniture).

If you use an inflatable mattress for swimming, then it is better to put it with a "native" glue or composition for rubber boats.

Material for patchwork

What material is better to stick an inflatable mattress? Suitable:

rubber from tire repair set;
old tire;
inflatable toy;
rubber haape for swimming;
an unsuitable inflatable mattress.

Cut the latch of the rounded shape, that is, without sharp corners. The size should be done so that the edges of the patchwork are for damage by 2-3 cm on each side. What she is more, the stronger will hold on.

How to prepare the surfaces

Before starting work, you need to blow away and carefully dry the product if you used water when searching for punctures. Then you need to properly prepare the place of damage and the patch. Here the value is the type of surface.

To make an inflatable mattress with a smooth side, you need to degrease the rubber surface and acetone latch, gasoline, White spirit or alcohol. A liquid for removing varnish is suitable. Then you need to clean the details of the fine-grained sandpaper, better than zero. This is done so that the grip will be as strong as possible.

To properly close the inflatable mattress from the velor side, you need to remove the darous coating. It is easy to make it easy: to wipe the area moistened in acetone or alcohol with a cotton disk, and after drying, remove the pile of the stupid side of the knife or, for example, a screwdriver. But you need to act carefully not to make new holes. Then glued surfaces are degreasing and cleaned with zero sandpaper.

Ways to make an inflatable mattress with Remkomplekt ...

Typically, mattresses are equipped with a set for repair from the manufacturer. It includes special glue, vinyl for lat raids and brief instructions for use. On average material is enough for two or three holes. If the latch is over, and the glue remains, do not throw it out, because it can be stored for about two years and is probably still useful.

And instructions for use involves four actions.

On the pre-prepared surfaces of the mattress and the margins need to be adopted with a thin layer.
Combine the items.
Strongly press. Just 20-30 seconds.
Suppose under the press at least four to five hours.

... and other means

And you can do without remarklet. After you have found a hole, we found suitable glue and latch, prepared surfaces, you can start repairing.

On the tube of any glue is written, how to use it correctly. If you do not have the opportunity to read the instructions, for example, the tube is very shame or paint is erased, the next table will help you figure out.

Table - Instructions for the use of various types of glue

Name	How to use
"Moment Crystal"	- spread the surface prepared surfaces with a thin layer; - give to dry 10 minutes; - combine the details; - strongly compress about 10-20 seconds; - You can use in a day
"Uranus"	- to fine-smear both surfaces; - add glue 1-2 minutes; - strongly press the details; - impose a press for 5-6 hours; - You can inflate the mattress after 24 hours
"Uranus"	- to finely impose glue into the details; - give to dry no more than 2 minutes; - 3 minutes to warm the surface with a hairdryer; - strongly pressing glued parts 1 minute; - It is possible to operate the product after 4 hours
"Desmokol"	- Apply a thin layer on both surfaces; - dried glue 10 minutes; - Apply glue re-; - Sew another 25-45 minutes; - 2-3 minutes to warm the part with a hairdryer; - strongly press 20 seconds; - You can inflate the product in 2 days
"Rubber"	- evenly smear the glue on the surface; - withstand 15 minutes; - combine the details; - strongly compress 20 seconds; - Place under the press for a day

Be careful: any polyurethane glue contains aggressive substances. Work in a well-ventilated room and wear rubber gloves.

If suture seam

Features. The patch, put on the junction of the top of the mattress and the bottom, can be unreliable even if all the gluing rules are met. There will have to have to sharpen and pull the place of the puncture through the valve.

What will take:

glue for PVC;
lattle.

Your actions

Unscrew the valve.
Strip the damaged area into the valve hole using, for example, a thick marker or plastic line.
Degrease and clean both surfaces.
Further act according to the instructions for the use of glue.

A plus of this method is that the patch from the inside is additionally pressed with air, which increases the reliability of gluing.

Method without glue

Features. If you have not been at hand of suitable materials, there is a way
Consider the mattress at all without glue and patchwork.

What will take:

iron;
paper;
smooth wooden surface.

Your actions

Pull out the damaged space through the valve hole.
Clear dirt and dust.
Align the edges of the break and put on a wooden substrate.
Cover the place of spike paper.
Ingress the heated iron.
Wait when the paper and the place of gluing will be cooled.
Gently remove the paper.
Fasten the valve.

Such a method allows you to cope with the gap literally in five minutes, but it is important to act as an iron carefully, not hurt whole areas. Otherwise, you can burn the mattress in new places.

Method with superclay

Features. This method is the easiest and most quick of the proposed. But it should be understood that the superchalter gives a fragile compound like thin glass. Such a composition is non-desarmed and inelastic. That is, it can burst at any time. But as an emergency measure, for example, in the campaign, it is quite suitable.

What will take:

super glue;
paper tape.

Your actions

Inflate the mattress.
Dry.
Clear and degrease the damaged surface.
Apply a small amount of super block.
Attach the wrap from the set of the desired size.
Quickly pass the edges and press the patch with force.
Give a glory to dry.
The product is ready to use.

If there is no power, you can do without it. In this case, you need to blow the mattress and drop one or two drops of superclone on the puncture (but not more) and give the composition to dry. Such a method applies for small damage like traces from pets of domestic animals or dry grass.

Method with "Liquid Warehouse"

Features. There is another method, just just and quickly fix the inflatable mattress without a patchwork. It is necessary to make a composition called "Liquid Lattle". The glue has many color solutions, there is even a shade called Intex. That is, designed specifically for inflatable products of this manufacturer. The holes up to 3 cm do not need additional fastening methods. And the cuts of over this size will need to sew a regular thread.

What you need:

tube "liquid beams".

Your actions

Disseminate the area with damage on a flat surface.
Clear dust and dirt.
Carefully degrease the surface with alcohol or solvent.
Vigorously shake the tube with glue.
Apply for damage, speaking by edges by 2-3 cm.
To withstand seven or ten minutes.
Apply the second layer of "liquid beams".
The product can be inflated after a day.

The gluing "liquid latch" is as durable as the intact surface. After spending once on this tool, you will provide your mattress for many years of life.

If "misses" the valve

Features. Not always the culprit of "leakage" is a rubber fabric or a broken seam. Pressure may fall due to a leakage valve. But this trouble can be eliminated with their own hands.

What will take:

small-grained sandpaper;
lubrication.

Your actions

Unscrew the valve.
Clean the grooves from dust and garbage.
Remove the rubber gasket.
Clean the end of the valve and the gasket with sandpaper.
Grease valve.
Screw the design to the place.
Inflate the mattress.
Apply a soap solution on the valve.
If bubbles did not appear - the mattress is ready for operation.

If, after all manipulations, the valve continues to pass the air, it means that the breakdown is larger and you need to replace the part completely. Contact a specialized store for the new valve.

How to avoid new damage

After successful repair of the mattress, it is important to consider past mistakes and prevent the emergence of new punctures and cuts. And for this you need to comply with simple rules of operation.

See where we put the mattress. Remove all the garbage, sharp objects, stones. If necessary, put the tight fabric, plaid or blanket under the mattress.
Do not inflate the mattress too tight. In the "finished" state, he must remain soft and pliable.
Do not allow pets of pets. Even just jumping on the mattress, animals can pierce the surface with claws.
Do not move the inflated mattress. Especially if someone already lies on it. The partitions and seams are so torn.
Do not sit sharply and do not jump on the mattress. These actions can also lead to the rupture of the seams and joints of partitions.
Run the product does not hurry. Let the mattress be blown on your own, excessive pressure can break partitions.
Wash the product with a weak soap solution. The smaller the aggressive "chemistry" you use, the longer the material of the mattress will save elasticity.
Before folding the device, dried it. The residues of moisture contribute to the reproduction of mold and cracking the material of the product.

So, do you have an inflatable mattress or circle? Conclusion: repair the inflatable mattress or circle with your own hands is quite possible. But if the above methods did not help or damage exceeds the size of 3-5 cm - it is better to turn to the master: service centers can be in stores specializing in the sale of home and recreation goods. Maybe they can help even in a shoe workshop.