Dampfer tape for PVC windows. The use of vapor insulation tape for plastic windows. What should be the parobarar

The replacement of windows in a residential or commercial premises is always accompanied by the protection of the weakest knots of the structure: seams between the frame and the wall. It is produced by filling the space between the window opening and the frame using the mounting foam. This material has excellent sound and thermal insulation qualities. However, with insufficient or incorrect protection under the influence of moisture and ultraviolet, the foam begins to collapse and lose its initial properties.

To avoid this, you need to take care of the seams of seams and filler protection. To do this, outside use waterproofing, preventing natural precipitation to the porous insulation, from the inside the vapor barrier for PVC windows, which protects the foam from the effects of water vapor.

Showing a pair barlasting structure for a plastic window

What should be a parobararier?

Vaporizolation does not make water from the room in the room beaten in thermal insulation material. The vapor-permeability coefficient of vapor insulation of internal seams for PVC windows should be no more than 0.01 mg / (m * h * pa).

To protect the joints use:

silicone;
suggesting cords;
lena psyl;
butyl rubber ribbons;
reinforced foil.

Psul ribbons are designed to create a mounting seam with natural ventilation.

The choice of the parobac was made with the subsequent decoration. So there is a material for dry construction (plasterboard, plastic), wet plaster, is separate to protect the joints of wooden windows in wooden houses, for internal and external use.

Tape can be like the same and double-tier

Butyl rubber tapes are like self-adhesive foam, but with a protective impregnation. With their help, all the seams between the window and the wall of the house are highly close. Also, the carbarrier for windows can have both one adhesive side and two.

There are vapor insulation for PVC windows for seasonal periods:

warm season with air temperature from 5 to 35 degrees above zero;
winter period with temperature below zero.

Read more: What are the harmful plastic windows?

Parosolation prevents the destruction of the mounting foam under the influence of moisture, prevents the appearance of raw corners in the window opening, the appearance of fungus and drafts.

If you do not make vaporizolation and slopes - maybe fungus

It should be noted that the price of vapor insulation for PVC windows is absolutely adequate and accessible to everyone. Very small costs of hydro and vaporizolation will allow to increase the service life of windows, and the house is to protect against drafts and mold in the corners.

Installation of vapor insulation for windows

The following are common rules for mounting vapor barrier for PVC windows, since for each individual type of ribbon can have its own characteristics:

The window frame and the opening is cleaned of dirt and dust.
The window without fixing is inserted into the opening, they are marked on the plastic seat of the steam barrier.
The window is removed and the marked places passes the parobarrier.

Hidden installation is made until the voids are gateing. The exterior tapes are glued only after the mounting foam will completely dry. In any case, the vaporizolation tape is glued to a continuous layer window.

Do not forget that the choice of tape depends largely on the type of subsequent finish. It is very important to use materials in compliance with all moisture-permeable characteristics.

Where can one buy? Prices

You can buy vapor insulation for PVC windows in any construction store. If you have to deal with the replacement of windows in your home, consult with the repairmen, what kind of parobarrier you are best choosing, taking into account the final wall decoration.

Real professionals will give you akin recommendations. But, if you came across the "specialists" that they assure in the unnecessaryness of the use of vapor barrier for windows, chase them into the neck. Whose incompetence may after bring you a lot of problems with dampness and drafts.

Hide

Vaporizolation is required for plastic windows. A vapor barrier tape allows you to close the joints, seams, protect the design from wind and precipitation. Thanks to this element, there will be no cold air through the joints, which will ensure the greatest tightness of the room and the minimum heat loss.

How to mount windows?

Modern builders most often use mounting foam. M. abouta tape for windows together with a sealant is applied after the foam dries. It is needed in order to protect the material from moisture, as well as close the possible slots and stop access of cold air to the room. If this condition is neglected, less than a year later there will be cracks between the window frame and the wall, through which the cold air will fall into the room. Drafts will appear, the windows will sweat and freeze on the joints.

Stages of installation of windows and widespread errors when installing them, see the link

When building a private house, you must think in advance, the height will be, which will be practical and better to look.

Modern builders often apply to install doors and plastic windows. Read the NVS on the site tips from professionals how to choose it

What is the steam barrier in plastic structures apply?

It is worth considering that the more correctly the installation is made, the more reliably the design will be and can last longer. Even if, but will be inserted incorrectly, you will not get the desired effect.

It is necessary to ensure that the working manner fulfill the following conditions:

The inner part of the mounting clearance should be filled with foam curves than the outer.
The system must be three-layer. The first layer of the street protects the entire pie from weather conditions, the middle layer is responsible for thermal insulation, and the inner layer protects against the formation of condensate.

The vapor barrier tape is necessary to ensure the protection of the design from water vapor.

In order for vaporizolation to do not interfere with plastering, special tapes should be applied, on top of which can be finished the room.

What should be aware of sealing?

Most often, the windows are attached using special bolts and: this material simultaneously serves as a reliable retainer, which allows you to adjust the position of the frame before the foam freezes, and high-quality insulation. However, the sealing for the material is extremely important, since when the moisture is inserted, the foam begins to deteriorate, crumble and turn yellowing, which negatively affects its properties.

To protect the foam, the mounting tape for windows is perfect. Even if you are going to use platbands that will protect the design from weather conditions, and will also be able to give the frame a decorative look, before assessing it is worth sticking to the tape. It will help to make isolation of high-quality, while it will make work more expensive.

The most inexpensive and easy-to-install vapor barrier for windows is a special tape, to cope with the sticker of which everyone can.

Steamer tapes for windows, as well as good decoration and mounting seams, will provide decent window characteristics. To the window in your home function well and for a long time you do not have to miss such a moment as the installation of a vapor barrier tape. Use the sealed tapes for insulation of the mounting seam from the vapor and moisture of the adjoining room prevent condensate output to the slopes. If you have a kitchen, a room with a swimming pool or a bath, then the installation of the vapor insulation tape on the windows you just need.

Varieties

Ribbons can be both with one and two sticky stripes. Two adhesive strips are intended for mounting the ribbon one side to the window, and the other to the wall.

Installation of vapor insulation tape

Same steamer tapes are classified on weather periods:

for the summer period with air temperature from + 5 ° C to + 35 ° C;
for the winter period with temperatures below 0 ° C.

Tape width It also varies depending on the needs, which makes it possible to ensure reliable vaporizion of the seams of various sizes. Choosing vapor insulating tapes, consider that its width should be somewhere 45 mm more width of the mounting seam.

Ribbons for outdoor work Consist of foamed materials (for this work, well-sealing materials with plaster mortar are needed, which will ensure the required vaporizolation of the outer layer).

Vapor insulation tape can be butyl rubberFor the tightness of interpanel junctions or to install door or window blocks. This tape contains a nonwoven cloth. In the process of installation, it is ground, plastering and painted. This type is also self-adhesive.

To protect against high humidity of the mounting seam under the dry finish of slopes in the market exist metallized vapor insulation ribbons.

Installed vapor insulation tape

General information on the installation of vapor insulation tape

Initially, you need to prepare your opening: Clear from dirt, dust and other garbage inner and outer surfaces of the opening and frame. The frame is inserted into the opening and is temporarily not fixed.
After gently note on the frame of the line for fastening the vaporizolation tape.
After calculating and applying the layout with the window, remove the frame and glue our internal vapor barrier tapes. The paper strip that protects the inner adhesive layer, which later attached to the walls do not remove.

As a rule, the installation of a vapor barrier tape on the design is performed until the seam margin. Therefore, before finishing, moisturizing and filling the foam, you can remove the protective paper strips from vapor insulation tapes. This will allow you to not lose the adhesive tape properties. If you are holding a hidden installation, then the tape must be attached from above and on the sides of the structure, and from the bottom to the installation profile.

The external thermal insulation tapes can be glued no earlier than the full polymerization of the mounting foam will be performed.
Installation of a vapor barrier tape under the windowsill can be recently produced. When the installation of a vapor insulation tape under the plaster layer occurs, then the tape should have an outer coating, which will ensure the necessary adhesion with this plaster layer.

In that case if the window is a quarter with gaps between the frame and the wall, Another technique is applied: an uneven joint can be closed with a nastener for windows, and already paste a vapor barrier tape. The installation of a vapor barrier tape on the window is mounted in a continuous layer over the entire loop.

Do not forget that the use of finishing building materials in a complex with a vapor barrier tape is allowed only under the condition that the moisture permeable characteristics are observed.

To protect the mounting seams in window openings from moisture exposure, a vaporizolation tape is used. It is made of butyl rubber or aluminum. This material is glued to the wet mounting foam on the seams, extending the operating time of windows.

Is it worth spending money on the protection of window seams

When installing the window in the opening, remember that its service life is associated with how literate will be installation. Even the highest quality designs will not be operated for a long time if the installation is made incorrectly. Due to incorrectly performed, moisture will gradually penetrate the walls, leading to the destruction of building materials and the spread of mold.

Conducting work on the installation of the frame, consider several important points:

On the inside of the room, we make a more dense layer of the assembly solution (for example, foam).
For high-quality sealing of all gaps, we apply three-layer protection - the outer material saves from the effects of precipitation, the average layer is responsible for thermal insulation, and the coating of the inner surface is for vaporizolation.

Parosolation ensures reliable protection of the heat-insulating layer from condensate, which is present not only in the bathroom, but also in the usual room. In the process of finishing the window slopes, we stick a special tape. The principle of vapor barrier is based on the overlap of moisture contact with the mounting foam forming the average protective layer. For these purposes, materials with low elasticity and bandwidth for water and air . When installing windows on vaporizolation, it is impossible to save. Such neglect will lead to rapid wear of the frames, plaster and finishing materials.

Special vapor insulation tapes are usually used to protect the seam. They are produced in the form of a rolled spiral and compressed material similar to a sponge. Binding moisture, the material swells, closeing all the existing gaps. A vapor barrier tape for plastic windows has a number of advantages:

1. Isolates moisture;
2. Consumable economically, almost without waste;
3. Does not highlight poisonous substances;
4. Easily pasted;
5. It has a long service life.

Classification - What features to pay attention

Tapes for insulation from moisture are produced with one and two strips of glue. The second option allows you to handle the joints of the window with a wall better. The material is classified by period of use:

summer (air temperature - 5-40 ° C);
winter (temperature - below 5 ° C).

Depending on the nature of the treated surface of the ribbon, they produce various sizes, thanks to which you can isolate any seams. Choosing the material, consider that it should exceed a 4.5 cm gap into width. To work on the outside of the building, tapes from foamed materials are suitable, which will ensure reliable sealing.

Tape for insulation from moisture

Adhesive finishing material made from butyl rubber is designed to process window, balcony, door boxes and connections between panels. Inside it is laid a non-woven layer. After sticking, such a strip is ground, plastering, glued wallpaper or stained. There is a full-bought vapor barrier tape made on the Robiband system. It provides better processing of the mounting seam.

Metallized vapor insulation material is used to wet the seams with joints in rooms with high humidity - bathrooms, baths, saunas. The glue layer over the entire surface in this form greatly simplifies the work process. Manufacturers produce metallized ribbon of different widths. Selecting the material, add 45 mm to the width of the seam.

The tape having a protective strip of polypropylene is well withstanding the mechanical impact. In addition, it does not react with acids, organic solvents and alkali.

We understand in the variety of species of ribbons - Sun or GPL?

The first in the list is psyms (pre-compressed self-sewing sealing tape). It provides high-quality adjacent window frame or door frame to the wall. This tape is used to vapor insulation of external joints and seams.

The following material is vapor insulation sun. It is used to close the seams when the dry finish is made. For example, under sandwich panels, drywall, plastic surfaces and so on. The tape has a layer of glue across the width - this property greatly simplifies the installation process. There is an improved option - Sun +. It is complemented by an anti-adhesive film. This additional coating provides a solid adhesion of isolation with construction materials.

Robiband Tape VM for vaporizolation is the following qualitative version of the material for processing seams. It is used for internal works, and the wet plastering solution is applied. VPM + is a complicated option with better performance characteristics.

Latest view - GPL (hydrotreating material). It is produced from high quality foamed polyethylene. The tape has one laminated side, as well as an additional metallized layer. The second surface is completely covered with glue. This tape is universal, that is, it can be used for all types of work. Its variety is a GPL-C tape having similar features.

How to stick insulation - work without errors

The vapor insulation material does not only provide protection against moisture, but also has an alternative property with proper stagnation - noise absorption. The application of a vapor barrier tape on the seams is made by one segment, there should be no breaks. Before proceeding to work, measure the length of the treated surfaces.

The process of salary consists of several steps:

1. Clean the opening of the windows from dirt, dust and garbage.
2. Before mounting, remove the PVC window and wipe the dry cloth.
3. Cut the design to the place and mark on the frame and wall of the fastening of the tape.
4. The tape is attached to the window frame until the foam is applied along the seam.
5. Remove the design and stir at its surface around the perimeter vaporizolation.
6. Before installing the window to place, remove the remaining protective film from the adhesive surface.
7. Sticking material, do not allow folds. This defect will pass drops of liquid under vaporizolation, worsened operational characteristics.

In order for the window structure to serve long enough, its installation should be made with accurate observance of the existing technology. The outer material for steam, heat and water insulation needs to be glued after the mounting foam is completely polymerized. We render a seam under the windowsill we last produce.

If the tape is glued under the layer of plaster, it should have a special layer that will provide a solid grip with the building material. An uneven junction between the wall and the window frame is closed with a nichelnik, and vaporizolation is placed on it. The use of building materials for wall decoration is permissible only if fully compliance with the requirements for water permeability.

If a metallized tape is used for vaporizolation, then when applied to a rough surface, additional strengthening may be required. To enhance the adhesive effect, self-adhesive tapes with one or two glue bands are used. They additionally handle the joints of vapor barrier, eliminating and smoothing the defects (peeling and wrinkling sites) formed during the work.