How to save on repair of apartments - tips for beginners and experienced masters. Where to start repairs in the apartment: the main strategy for performing work Cosmetic room repair do it yourself

For repair you will need various brushes and rollers

Rooms in our house have a different appointment and each of us has its own vision of the necessary transformations during repairs. Therefore, we will consider only one of the room repair options. We will analyze in detail how to make repairs in the room with your own hands an average resident who knows how to keep power tools and is ready to learn and work independently.

What do we do

We will analyze the simplest repairs in the room, but with the addition of the cabinets with the shelves. Ceiling make one-level with a glued figure. Walls with wallpaper, and on the floor Laminate bed.

Preparation for repair

Facing wall tiles

First of all, you must endure all things from the room. Now we need to clean the walls from old wallpaper, paints and limes. If the plaster falls off or "breathes" - it also needs to be removed from the wall. In any case, those sites that do not stick to the main wall.

Now we will deal with the floor. Perhaps in your room there is a wax floor, the boards of which are in good condition. In this case, you will have to dismantle only the plinth. If the boards are bad or bend - tear such a floor and do not spare. Perhaps the linoleum is pack on the floor. Remove it and check the evenness of the screed. On 1, the gender meter of the floor should be no more than 1-2 mm drop. If the difference is greater, then you will have to or fill the screed, or use the floor alignment.

Pay attention to the state of the interior door. Maybe it is also better to dismantle it with the door box to set the other.

Window

If the room needs to replace the window, then do it now, at this stage of repair.

Electricity

Casting walls by wallpaper

The room definitely needs light and power supplies, that is, sockets. At this stage of the room repair, it is time to make wiring wiring. Determine immediately, where lamps will be (walls, ceiling) and move the wires to these places. Provide a sufficient number of outlets in the right places. All wires passing on the ceiling to grind into an electric corrugated hose.

On the wall, if necessary, make a shifts for wires. For the room of this purpose, a copper wire is required, a cross section of 2 square meters. mm. Lamps, sockets and switches Install the ceiling after painting the ceiling and beat the wallpaper.

Floor

If you decide to fill the screed, then pour it so that it is on the same level with the main floor of the apartment. More information about the pouring screed can be obtained.

Maybe there is an old good screed on the floor, the drops of which do not exceed 2 cm. In this case, use the floor alignment. How to work with floor alignment on our website.

Putty and slopes

Installation of sanitary ware

Putting the walls of the starting putty. Will you use lighthouses - depends on you and your walls. Perhaps the walls are smooth, or almost even that for wallpaper is not so substantial. It can be said that if 0.5 cm of the slope is observed on 1 m of the walls in one or another - it can be considered suitable for putty under the wallpaper. The angle of such a wall can be aligned with the help of the rule, without lighthouses. However, you can make a loaf putty. How to do it, you can see.

Sucks, in addition to the starting putty, you will have to put out once again by SatentHipse or finishing putty. This can be done when you put the ceiling and the end.

After starting wall putty, set the door frame. The interior door is better to do without a threshold - it is more convenient in operation.

Plasterboard Tumba

Plasterboard Tumba

You can skip this part of the interior, but for those who want to have additional shelves in the room, we will tell you how it is done.

For the markup of the cabinet, we need a pencil, roulette, level, plumbing and construction kit. Bottches will make 60 × 60 cm along the outer perimeter. In the corner of the room, on the ceiling, with the help of a constructional carbon outline the perimeter of the couch. Using a plumb to transfer these sizes to the floor. We use UV and CV profiles 75 mm wide. We screw to the ceiling and to the floor on the side of the deaf wall slices of the slices of the UV profile.

Now set the four corner profiles of CV, and three of them screw to the wall, and one, external, screw only to the UV profile.

Now cut off the size of the pieces of CV profile and, trimming them in the right places, we make partitions for the shelves. For partitions, we use both types of profiles by installing not only side, but also intermediate fasteners. To screw the profiles among themselves, we use small screws, called flews. Sewing the frame with plasterboard sheets will be after installing the ceiling. You can put out and paint the tube simultaneously with the ceiling.

Ceiling

Repair results in the children's room

Now reached the ceiling. Mount the frame for a smooth ceiling and hang drywall sheets. Installation instructions for ceilings. Before putting down the ceiling, we are wearing a tumb with shelves with plasterboard. Split ceiling and tumb. After the putty dries - we can paint the ceiling and the end. After painting the ceiling, the lamps can be installed, which are provided for the ceiling.

Wallpaper

Walls have already been dried. You can glue wallpaper. The instructions for sticking wallpaper can be found on. After the wallpaper pasted, you can install sockets, switches and sconces.

Laminate and door

Stele laminate and hang the door. If you find it difficult to lay a laminate, then read on our website. Do not forget about door platbands. Now it remains to fasten the plinth around the perimeter of the room and the repair can be considered over.

Make repairs in the bedroom with your own hands - the dream of many premises owners. Although this is not a "public" place in a house or apartment, children do not play here, guests are not going to visit or the whole family, repairing in the bedroom should pay quite a lot of attention.

At the same time, many want the interior to meet all the ideas of their owners, they invest their most uncomfortable dreams. How to make repairs in the bedroom with your own hands will tell this article.

The bedroom is a room where every person spends enough time. The room can be multifunctional or adapted only for sleep, which requires relevant technical and design techniques.

This leads to the fact that before repairing the bedroom, you should thoroughly consider all its stages, given the varieties of such a room as it will be used how the renovated room will look like.

According to their cumulative features of the bedroom, such categories can be distinguished:

Sophisticated or parental. Here you need to create the desired psychological attitude for both spouses (see).

Children's (cm. ) . This room, where children not only sleep, but also play, make lessons what requires a special approach to its design.

Bedroom bachelor(cm. ). Its features are that it is usually a small room that can easily be transformed from the recreation area to the office or a bedroom for two.

In one-room apartment. Such a type of bedroom is characterized by its multifunctionality. She is a married, and a room for children and a dining room. An example of a studio apartment is shown in the photo.

Any of these species may have a simple configuration in terms of or to be with Alcove, have:

Bed niche.
Balcony or loggia (see ).

What types of repair

The degree of increase in complexity characterizes the type of repair of bedrooms.

He can be:

Cosmetic or simple. In this case, the repair is reduced to cleaning the room, it is possible to replace the window or the balcony block, the wallpaper plywood. Before it holds, the main thing is to choose the right wallpaper and new furniture. With this repair:

a new solid flexible floor covering on the existing, without performing the repair of the floor;
changes change (see);
lambinos suspension;
installed, if necessary, screen.

Decorative. This is a more complex room repair. This includes in addition to the above events:

device of a new ceiling;
new wall decoration;
floors are played;
may be insulation of a balcony or loggia;

These are quite complicated work, but still fully done on their own. The decorative repair also includes the installation of light partitions from puzzle blocks or drywall, plywood or lumber.

Capital. It is in addition to full cleaning of the room, its drying includes:

overhaul of walls, gender, ceiling and device of their insulation;
repair of the floor at which the screed is changing and its sealing, insulation and vaporizolation are made.

Renovation. The concept of "renovation" is a style, creating an unusual appearance of a bedroom, which will express the individuality of its owners. This repair can be of any kind, even cosmetic, but it requires or a good artistic taste of the Owner of the premises, possessing them by special techniques of work, or recommendations of an experienced designer. The price of the Eurore repair, in any case, will be quite large.
Repair with redevelopment. In this case, most often performed:

balcony combined with bedroom;
severe capital partitions are arranged, giving a large concentrated load, which acts on overlap;
device in a bedroom Panoramic or French window.

At the same time, the repair requires the development of a project, a special permission to work, accompanied by complex documentary designs, professional technical supervision for carrying out all operations, their acceptance confirmation of the act of putting commissioning. The execution of such works is possible with the experience of a builder who can do technical calculations and knowing the bottom. Repair with redevelopment on its own forces is made only in exceptional cases.

Tip: In any bedroom, there must be a corner for the Bouire device, which will be placed: chest of drawers or wardrobe, tremor, ottoman. In a bachelor's bedroom, the functions of the Boudoire and the table for work perfectly combines a secret meter with a mirror arranged in his niche.

Room with constructive features

When it comes to bedrooms, it is quite common to another problem: the room has a configuration of the foam, that is, it is narrow and long. Let's see how professional designers come out of this situation.

Such a room must be defined, and you see the bottom of the bottom, which is done with the help of a suspended ceiling with backlight and curtains.

So:

Caissional plasterboard ceiling is made only in that part of the room, where the bed is standing, and it is under the window. Therefore, the heating battery was closed with a decorative lattice, the shutters of a roll type were hung on the window. The curtains were not located above the window, as is usually done, but before the bed, thus creating a kind of boudoir.
A similar idea may be interested in the owners of "Khrushchevok", where there are rooms like this configuration. By the way, partial zoning can be performed by the arrangement of a figure drywall. Most often, it is an element of the ceiling and wall zoning design.
A one or another version of the separation of the room on the zone is selected taking into account the location of windows in it. An example with the Boudo is good when the window is located in the far end of the room, as it is more often and happens.
On the example below, it is located on the side wall, close to the entrance.

The bed is in the unlucky daylight of the part of the room, and if it is closed with curtains, the sleeping area will be practically in the dark. Therefore, another version of zoning is chosen here.
A short curly septum separates the zones only visually, not lighting up light. Due to insufficient daylight, for finishing this bedroom, white, and muffled pink color are taken as the basis.
And also, in high-rise buildings there are long balconies with two outlets, one of which is in the bedroom, or it can be a loggia. Anyway, it is not entirely convenient, and a desire to remove this door appears, especially since the rooms with a balcony often there is an unimportant lighting.

What can you come up with this situation? The door leading to the balcony can, of course, remove, but only if it is well to isolate and spent heating there. Now there are all the possibilities to do this - however, they will require certain costs.
It is necessary to close the gaps, for all the rules, insulate the parapet and the balcony ceiling. The ceramzite concrete screed will raise the floor above, and the coolest floor system installed under the floor covering, even relieve you from the need to improve the balcony of traditional heating.

How to make repairs in the bedroom

Instructions for repairing the room includes:

Designed design project.

It reflects what should be the type of bedroom after the completion of the repair. A sketch is applied on paper or reproduced using a special computer program, if available.

At the same time, it is necessary to take into account all the size of the room, to properly perform the zoning space of the room. Typically, the bedroom is isolated from all other apartments, but here you can organize a dressing room or place to work.

Compiled estimates for repairs.

After determining the design of the room, a list of materials necessary for performing work is drawn up, and costs for repairs are formed. At the same time, the main condition is to properly maintain the ratio of good quality and reasonable price for repairing the premises.

Prepared workplace.

Before starting repair, the bedroom should be taken out of it all the furniture, shoot chandeliers, sockets and switches. If you do not plan to change windows and doors, they need to be protected with a special scratch and dust film.

The old coatings are dismantled.

It is removed:

old wallpaper;
traces of blissing;
paint;
old tile;
spoiled flooring.

Dismantling is a long enough procedure that requires certain skills and attention. It is necessary to remove the plinth and thresholds.

The room is re-posted, and its structural elements are replaced.

Repair can begin with redevelopment of a room involving a demolition or device of partitions. In addition, when repairing the bedroom you can do:

replacement of radiators;
installation of air conditioners;
carry out electrical work;
replace windows and doors.

Tip: Bedroom, more than another room, should be separated by environmentally friendly materials, safe for human health.

How to separate the ceiling in the bedroom

The ceiling takes a significant place when room design.

He can be:

Spacure.

This is a rather laborious process that requires skill and experience.

From drywall.

Such a device can be performed independently. The advantages of plasterboard designs are:

aligning surface drops;
concealing all communications;
suitable for the device of any lighting;
are an ideal option for creating multi-level structures of any complexity.

Stretched.

The features of such devices can be:

they hide all the flaws of the ceiling surface;
protect the room from an unforeseen fall into the moisture room from the ceiling;
wide selection of textures and colors.

Stretch ceilings can be arranged in multi-level versions, where they will introduce a note of uniqueness and uniqueness to the bedroom.

Much attention must be paid to the color scheme of the ceiling. It depends on the dimensions of the repaired premises and from the style used. Reduce visual space dark colors, but increase - bright.

Tip: The bedroom does not recommend installing glossy and multi-colored ceilings that distract attention and not contributing to relaxation. All shades are chosen so that they are calm and unobtrusive, and for inclusion in the interior of a saturated color, it is better to fulfill a small color accent in the middle.

Window repair and doors

The doors are chosen in such a way that they are combined with the design of the entire premises. Windows is an important element of the interior. Their form and dimensions dictate the design of the room.

In addition, they prevent the penetration of cold to the bedroom, have thermal insulation properties. Soundproofing of the window depends on the thickness of the glass, the distance between the glasses, the density of the joints.

Depending on the type of window opening, they can be:

Combined.
Swing vertical.
Swing horizontal.

There are a variety of windows:

Standard plastic.
Original wooden with an attractive design.

Tip: When designing a plan, you need to consider the windows to be directed to the south or east. Then, in a sufficient amount in the room will flow sunlight, which improves the work of the human body, stimulates the activities of the CNS and controls the metabolism.

How to separate the walls in the bedroom

Wall decorations - the main operation during the repair of the room. First of all, they are leveling.

To do this, you can use one of the options:

Alignment of walls of plasterboard. This is a simple and cost-effective option. Plasterboard can be hidden rather large differences on the surface of the walls and create a perfectly smooth surface. The disadvantage of the material is to reduce the area of \u200b\u200bthe room and the unusual hollowness of the walls of the room.

Plastering. This is a more difficult, long-term time and costly procedure. In addition, it cannot be used for premises where large surface drops. The advantage of this method is to preserve the useful bedroom area.

For finishing walls of walls in the bedroom, wallpaper or decorative plaster is most often used. When choosing wallpaper:

Tip: The most optimal option for wall decorations - paper wallpapers with environmental cleanliness and acceptable cost. The only lack of them is a low life.

Those who are creatively approaching the organization of the interior can be bought by phlizelin wallpaper under painting. Such materials are well passed air, eco-friendly, they can be repainted, if desired, change the color and style of the room.
Textile wallpapers are quite original in the bedroom:

have a long service life;
big abundance of colors and structures;
provide excellent sound insulation indoors.

It allows you to create an original artwork in the bedroom, and its owner can be sure that his room design will be the only and unique.

Color shades for the bedroom are best to take:

Blue.
Light green.
Pearl-gray.
Light pink.

How to repair Pol

The floor in the bedroom should not be cold. If possible, it is better to arrange the installation of the "warm floor" system.

As an outdoor coating, you can use:

Laminate. This is an affordable material, it easily stacked. The coating does not require much care, but when installing under it, the soundproofing substrate should be paved.
Parquet. The material is quite expensive, very capricious and requires special care.
Linoleum. It has high wear resistance and unpretentious in operation.
Cork floor. The coating is pleasant to the touch, warm, comfortable and environmentally friendly. Does not tolerate aggressive means when cleaning.

Bulk floor. Original and modern finish. With it, you can get a very smooth surface to which 3D image can be applied.

Tip: If the bedroom is small, a visually more volumetric room will make a laminate or laminated on the parquet diagonal.

Installation of furniture in the bedroom

The repair of the bedroom selection of textiles ends:

curtain
gardin;
bedspread;
cape;
pillows decorative.

Podium for the bedroom

The easiest option of the podium is a frame of a wooden bar, covered with glued plywood or wood-polymeric plates OSB. As a facial finishing, the podium body can be separated by carpet, piece parquet, laminate, cork coating.

So:

Experienced specialists are managed, with the help of the podium, organize the space of the most close bedroom so that everything is necessary in it: from the table, to the lounge cabinet. In general, it is believed that the podium needs to be done: either in a small one or in a fairly spacious room - the main thing is that the ceiling height allows it.
In the interiors decorated in Japanese style, you will almost not see traditional beds - just a soft mattress installed on a low podium. In the big room, it can be in the center of the room. Then it makes sense to decorate its surface of expensive wood, make backlight.

If you, starting the repair of the bedroom, decided to make the podium, in this part of the room will need to dismantle the flooring. Further, you will have to align the base and set it up with a cork substrate, which is usually placed under the laminate. This layer will not only serve as a shock absorber, but also provide normal sound insulation.
The size of the frame for the frame must be seamlessly taking into account the alleged loads - if it is only a bed, the sections of 30 * 30 mm will be quite enough. In principle, for this purpose you can use the aluminum profile, especially if the podium will be shed GVL. The distance between the vertical racks should be no more than 40 cm.
In those places where the podium is adjacent to the walls, the frame elements can be rigidly fixed on their surface. The horizontal and vertical belts are installed at right angles, if it are bars, they should be additionally fixed with metal corners.

If the podium is used to use the phaneer horizontal surface, then in order to not feel the deflection under load, you need to take a material with a maximum thickness (21 cm). The use of OSB plates allows to reduce thickness up to 15 cm - they are much stronger than plywood due to the polymer filler. Hypus fiber sheets (GVL) may have a thickness of 12 mm, but the step between lags, and it should be less than: 30 cm.

To build such a design, no special knowledge is required - every second man will perfectly cope with this task. To cover the visible vertical surfaces, the manufacture of the facade side of the drawer, you can take a chipboard with a laminated coating, or use parts of unnecessary cabinet furniture.

Loggia as part of the bedroom

What the most urgently urges any room is pipes and heating radiators, hide which is not always possible. And if there is also an exit to the loggia, the whole wall is practically not involved in the design.

So:

You can, of course, hang chic curtains, but if they are constantly torn, leaving for a balcony and back, their appearance will rather soon be crying. You have to move the porter so that it does not interfere with the freely walk.

For this reason, the owners of such premises often prefer to combine the room with a loggia. Why exactly from the loggia, and not with a balcony? The answer is simple: the balcony is a remote design, and make it the same warm as the room is quite difficult.
The loggia in principle is part of the indoor room, and it is not balcony plates, but the slabs of overlapping. Therefore, in winter in the location of the loggia, much warmer than on a glazed balcony - and this is very important, especially for the bedroom.

Before removing the window and the door, you need to get rid of the battery under the window and solve the main question: how the room heating will be carried out.

And the choice is:

If the parapet makes low or do without it without it, setting the glass wall, the bedroom will have excellent natural light, and you will please the panorama of the city, which opened the look. It will only need to raise the flooring level of the loggia to the floor of the room, make a common floor covering and finishing, harmonizing with a common interior - and get a large bedroom with a separate area assigned to relax or study.

Do not forget that the inner decoration of the walls and the ceiling on the loggia must be performed in a skeletal way. This will provide an opportunity to make waterproofing surfaces and lay the insulation layer under the trim. By the way, removing the window and the door leading to the loggia, the simplest, which is located under the window, can be left - it will play the role of the zoning partition.
The opening can be issued with a contrasting platband, mounted along the wall, and on the ceiling beams of the same color, and you will get a design, about as in the picture from above. And also, over the simplest, you can install a decorative septum of wood or drywall.

If you can prefer to leave the simpleness, then the battery can not be removed, but to close it with a decorative lattice. As an option, on the basis of the simplest, you can make the table, the benefit that its height is perfect for this suitable.

All the details of the repair of the bedroom well shows the video in this article on the topic: "We make repairs in the bedroom with your own hands."

Many wonder: how to make repairs in the apartment with your own hands to save money. After all, inviting experienced finishers, you will have to pay considerable money.

This article will tell about the main stages of the decoration of apartments.

Types of repair

To begin with, let's see what kinds of repair is:

Capital

During such a finish, a completely type of apartment is changing, that is, new doors and windows are set, another coating of walls and floors is applied, plumbing is being reconstructed, the location of the sockets can be changed.

You can always use Intel Desing's services, the main direction is to create a unique interior design for your apartment.

To reduce cash costs and time to carry out overhaul, you need to make a plan for work.

Cosmetic

It implies work, which will update the view of the apartment. This includes the decoration of the walls and the ceiling, the change of flooring.

Time and cash costs will be needed less than on overhaul

ERRORORMONT.

In the 90s. This concept meant expensive work on European standards. Now it means modern apartment repairs, the use of bold design solutions, the use of zoning rooms and much more.

The result is the exclusive room in which it will be comfortable.

If you need to completely transform housing, you choose a renovation. But you need to remember that the price of such a transformation is high.

Before you begin work, you need to create a housing project and come up with a design.

Main steps

First you need to make a phased plan of your repair. It will help calculate costs and calculate how many materials will be required.

The main stages of repair will be the following

If overhaul is required, first of all, partitions are installed, align the floors, plaster the walls and mount the ceilings.
Then are engaged in floor coating.
Mounted plumbing.
Install the doors.

Before starting work, you need to clean the old finish. Leave old wallpapers and glue on them new, as some do not, it is impossible, as they can turn around with new ones. Then eliminate the remnants of glue, clean the cracks.

The most important process is the installation of wiring and pipes. To do this, make the shoes where the pipes and cables are placed.

If construction work is performed by experts, they need to be asked to make a plan of communications. This will help to further avoid damage to pipes and cables.

The next step is to install windows. When they are ready, you will have to close them with a glue, so that the dirt does not get.

Note!

After the windows, you can move to walls and ceiling. The surface is maintained, sweeping and ground. Grounding of walls is required to give strength. When it dries, you can start painting.

If you want to change the floor, it is better to use a self-leveling solution. It will require less time than the screed on its own.

Now you can proceed to pasting with wallpaper. Beautiful renovation in the apartment can be performed using cheap finishing materials.

The main thing is that everything looked harmoniously. Be sure to combine the drawing on the wallpaper and align so that they do not bubble.

Outdoor coating can be any. If you put a tile, then you need to do it after the ceiling finishes.

Note!

Ceiling can be cheered, paint or lay out ceiling tiles. Many are installed mounted ceilings, which also looks great.

At the final stage, the doors are installed. Then you can proceed to the placement of furniture and the addition of decorative elements.

Numerous photos of repairs in the apartments are on the Internet. If you can not determine with the design, they will help you.

In order to repair the repairs delivered joy, you need to adhere to certain rules and listen to the following advice:

In order not to disturb the noise from the corridor, there were no drafts, you need to install doors with high sound insulation.

Before starting repair, be sure to export furniture from the home so that it does not be damaged.

Note!

Do you have little children? So choose washable wallpaper to waste their drawings easily.

You can not save on wiring, as cheap cables can start melting, which will lead to a fire.

If you do not want the pipes to be on the surface, then you need to purchase polypropylene, whose connections are soldered. Metal plastic spinning, and they will sometimes pull them up.

If it is impossible to align the ceiling to the end, you need to install the tension.

In order not to be filled with plaster from inter-stoves of overlapping, it is necessary to coach the seams.

As you can see, make repairs in the apartment on its own not so difficult. The main thing, do not deviate from the basic rules and everything will turn out.

Stock Foto Repair apartment with their own hands

March 24, 2018 no comments

Repair of residential premises always opens several options for its owners: take it into your hands, or seek help to professionals. The second option is much simpler, because the interior has a designer, and over the embodiment of the project - a brigade of narrow specialists, where everyone is responsible for specific actions. And before making repairs in the room with your own hands, you need to shut up not one site of construction subjects. Yes, and skills, at least initial, are very desirable.

This question is most often considered from the material side, because price tags for designers and repair and construction teams are high, and their own finishes will always help save a substantial amount.

When weighing everything "for" and "against", everyone stops at a closer look for themselves, and our article will be a guide for those who decided to act independently. So, repairing the room with your own hands where to start, what to buy and how not to spend extra money on ruinous waste of materials. About everything in order.

We compile an action plan that the project is marked with an independent design. It should include not only the decorative design of the room, but also to display all the power points and lighting devices, the placement of furniture and even the placement of textiles.

A schematic representation is better to create with marking of dimensions and in proper scaling to be able to purchase materials in the desired quantity. This will allow you to not waste extra money for waste, select the optimal width of the wallpaper for individual walls, a suitable number of panels, tiles, etc.

Purchase of materials can be carried out in the construction market, but supermarkets offer more loyal exchange / return conditions, pleasant discounts when buying for a large amount and address delivery. In the framework of one construction hypermarket you can buy absolutely everything, to the finest things. At the same time, this is in comfortable conditions and with the ability to consult from specialists.

Preparation of the project using a special program or paper with a pencil, as well as the purchase of the necessary equipment for repair can be considered the first paragraph of preparatory work.

Before making repairs in the room yourself, the room must be carefully prepared. We carry out of it all furniture and interior items, things and indoor flowers.

Depending on the complexity of the repair, we define those objects that remain in it: switches, sockets, window sills, doors, etc. If all this is not subject to replacement, it is necessary to isolate them with the help of film and painting tape. The floors and the plinth are also better to store.

The whols are washed away with roller and warm water. It is not necessary to unwind the entire area at the same time, but 1-2 square meters. Spired - removed the layer with a spatula.

If the layer thickness is large, then we welt again and remove everything up to the slab overlapping or old plaster.

Paint on the ceiling is removed using a rigid spatula or sandpaper, but faster and more efficiently soften it with the help of special solvents. Such are sold in business stores and construction markets, it is inexpensive, but they are able to soften even a very thick layer of paint for up to 24 hours.

If the ceiling was wallpaper, you can remove them in a dry form, and remove the remnants of glue using moisturizing and the same spatula. In any case, all loose remains of the old finish are removed, there is only a real-life, dense part of the design.

The same procedure applies and in relation to the walls. We break and wash off the whole old finish, we remove the rebels if necessary. Carefully remove the floor and prepare materials for the start of finishing work.

Actually repair

Primer - it is the procedure with which it is worth starting room repair with your own hands. It is sold in the form of a liquid solution, and is applied to the surface from a special tray using a roller. There are and wide brushes that will help primrate in corners and hard-to-reach places.

We apply one layer on the ceiling and walls, let dry according to the instructions. At this stage, it is necessary to qualitatively protect the eyes and open areas of the body, since the primer is toxic and can provoke a chemical burn.

After the wall "grabbed" and ceased to absorb liquid, it can be considered prepared for the application of plaster. The latter can have a gypsum or cement-sandy basis, the plasterboard sheets mounted with metal structures or glue can replace it with it.

Most often, drywall is used in the case of large paares in the level of walls and ceiling, its significant disadvantage is the large thickness.

Monolithic plaster will be more expensive, its application will be much longer. However, its presence on the walls will practically affect the room area. Just like at the height of the ceiling, if applied it there.

After a complete drying of the plaster, there is a turn of the next bed of primer. Then - finish finish in the form of putty and grouting the surface with a special grater. It is applied to a putty very thin layer. The purpose of its use is the elimination of the surface of the surface, which is achieved through the use of coarse plaster.

Prices for popular types of plaster

With a wide spatula or rules, it is smoothed on the surface of the ceiling and walls, after which it should completely dry. In order to avoid cracking on the corners, a painting mesh is put here, which the spatula is a little deepening in the still crude putty. This will make the surface stable, and the repair that you have to do is more durable.

The grid necessarily paces when finishing the slopes and doorways, it is appropriate to use the finished plastic corner, along the edges of which this textile is already present. Further processing of the walls depends on what is selected as wall cladding and ceiling.

If the surface is overlapped with panels, wallpaper, cork or other, fairly thick and opaque materials, then it can be not subtle with a thin processing.

If your choice fell on painting, the database state must be closer to the perfect. After all, paint, even applied in several layers, can produce imperfections of processing.

Final arrangement and decoration

After all the steps of processing and drying the ceiling / walls, there comes a turn of the most interesting - salabing or staining of surfaces.

Wallpaper will always give a wide variability of combinations, since most collections are produced in the palette: drawing + monochrome companions. Paints will help express the creative beginning, and ensure that such a picture on the wall belongs exclusively to your housing.

Cork, photo wallpaper, embossed paper panels or analogs from the Fiberboard are also considered in terms of design, as a very original solution. However, selecting materials for finishing is based on considerations of ease of daily care during operation, as well as fire-safety properties.

If the floors in the room also need fresh solutions, then for rooms you can consider laminate or carpet, carpet tile or linoleum on a felt basis. The installation of these materials is adapted to self-realization, there is an opportunity to use glue or simplified locking system.

After the walls of the walls and the final finish of the ceiling, it is for small - installation of lighting and furniture alignment.

After careful cleaning of the room, you can enter the furniture here, pre-supplying it with the legs with felt "patch". This will help you maintain the integrity of the floor cover as long as possible.

Video: Room repair do it yourself: