How best to lay a laminate in a rectangular room. How to put the laminate - along or across: tips on choosing a direction, from where to start laying and step by step processing. Different castle systems require a different approach when performing Ra

The laminated floor covering has become one of the most popular, thanks to the beautiful form, simplicity of laying and quite affordable price. A variety of color solutions and methods of laying lamellas along, across and diagonally the rooms give space for designer solutions.

With independent repair, such a coating can be considered the most convenient for laying. Separate elements are connected with each other with special lock-locks on the edges. If you carefully comply with technology, time will be required quite a bit, and the result will please.

Laminate location methods

Depending on the type, the color of the coating and ideas of the designer can be used by various methods of lamellas. The visual effect depends largely on how the light comes from the windows. If it is necessary to ensure that the coating seems to be monolithic, the lamellas are located along the direction of light.

This makes the jokes less noticeable. Some types of laminate have a special chamfer that creates the visibility of individual boards. When using them, it is desirable, on the contrary, emphasize the joints, placing perpendicular to the light line.

It is also important to take into account the shape of the room. Specifying the direction of the lamellae, you can visually change the ratio of the room:

In the room of the correct rectangular shape of the laminate, it is customized along the long wall, from the window to the door.
In a long elongated room, the laminate is better to sharpen across, since the transverse strips visually expand the space.
If the room is incorrect, hide this drawback will help laying the flooring diagonally. This method is somewhat more complicated - it will require more time and consumption of materials will increase.

Tip! The direction of laying laminate is especially important if the large floor area will be open: it will not be located furniture or carpeted coating. In small rooms, the area of \u200b\u200bfree sex is usually small, therefore it is worth choosing the most economical way of laying at which there will be a minimum amount of waste.

Laying of laminate along or across

Deciding with the direction of laying, it is possible to calculate the materials. It is easy to do with the help of an online calculator on the manufacturer's website or seller. Buying laminate, pay attention to the instruction available on each package.

Modern locks have a more advanced design, which greatly facilitates and speeds up the installation. In addition, the service life of such a coating will be more, so do not save on quality. After purchasing the packaging, the lamellas should lie down in the room for several days to stabilized the level of humidity. This will help avoid the deformation of the coating.

The most important stage is the preparation of the foundation of gender. It should be dry and smooth. The deviation should not be more than 2 mm per meter. Any tubercle or vpadina will create a load on the joints, which can cause a screen or even breakage of the castle.

To properly prepare concrete floor, you may need a self-leveling screed, which will make the floor even and smooth without much effort. The wooden floor is usually aligned with plywood sheets with a thickness of 10 mm, which are fastened with self-reasons to the base.

On an even base of the floor, a special substrate under the laminate must be laid in obligatory. It depends on how comfortable and long the use of your floor covering.

Choosing a substrate

From the selection of the material to which you put laminate, depends:

will the floor creak;
how long will it last;
how loud will be heard steps;

will it be warm by your feet;
will be dents from furniture.

Just like laminate, different types of substrate are distinguished by quality and price. Often, the manufacturers of the floor covering insist on the use of a specific substrate, the warranty action depends on this. This often requires the use of a certain material with a given thickness.

As a rule, the higher quality material, the higher its cost. For economy class laminate, it is pointless to acquire an expensive substrate, because it will last longer the coating itself. You will have to determine the golden middle of you yourself.

Consider various types of substrates based on:

Foamed polyethylene in rolls, having a different thickness, most often offered as the most accessible option. It does not miss moisture, enough elastic, has certain thermal insulation and noise absorbing properties. The main drawback is a short life, after 5 years it becomes unsuitable for use.

Order stacking

When the base of the floor is properly prepared, the materials are purchased and supplemented in the room, the flooring can be accommodated:

Tip! If you are styling outdoor coverage yourself, learn not only the instructions, but also several video lessons. This will help avoid common mistakes.

Laying of laminate - a quick way to transform outdoor coverage in the room. It can be kept both along and across, depending on the effect you want to achieve. If you want to save, it can be done independently, following the instructions of the manufacturer.

Laminate is considered to be one of the most popular types of flooring. It is distinguished by beautiful appearance, durability and simplicity of installation. However, all work on its laying should be carried out in accordance with certain requirements, otherwise even the highest quality material will come into disrepair too quickly. Many beginner masters have a natural question: how to put laminate, along or across the room? There is no unequivocal answer to it, so you will deal with what will depend on the direction of the orientation of the lamellas during laying.

How to put the laminate - along or across

If you listen to the advice of experienced masters, you can hear that there is one rule, according to which the orientation of the lamellas in the rooms. The direction of the coating planks is completely dependent on where the main light source is located. (for example, a window or bright lamps that will replace the first option indoors without windows).

Why will the direction of lamellands depend on the light source? Everything is simple - the rays of the sun or light from the lamp, falling on the material perpendicularly (at an angle of 90 degrees), will show all the joints. Especially they will be noticeable if the slats are docked poorly. And therefore, the laminate is always stacked so that the coating strips are located along the light rays - then only you can reduce the visibility of the joints. Thus, the lamellas will lie down by their narrow side to the window, and the installation of the coating is performed, ranging from one of the lateral walls of the room (usually from the one where the doors are not).

On a note! Where there is no natural light source, laminate is put, focusing on artificial.

Prices for laminate "Tarkett"

laminate Tarkett

Direction of laying laminate

Laminate manufacturers note that any person will cope with this coverage and with this task will cope with any person. Yes, it is partly the truth, since the slats are equipped with special locks that allow them to be easily fastened. If it was originally on sale laminate only with Lock lock, which requires certain skills to work with it, now a new type of connection has been widely spread - these are click locks, which really can do anything. We will talk about them a little later.

On a note! Technologies do not stand still and develop, in connection with which there are completely new lamellas that have 5G and Megalock connecting systems.

In fact, everything turns out to be much more complicated than kindly reported manufacturers of laminate. This in particular concerns not only thorough preparation of the foundation, but also the orientation of the planks in the room space. Most often in apartments, laminate is laid depending on the direction of light, as mentioned above. If the planks are laid along the light source, the floor will resemble the usual boardwalk, and the joints will not be noticeable.

But sometimes it makes sense to cover and perpendicular to the direction of the rays of the sun or lamp. So due to the coating, you can visually enlarge the room, which is relevant for narrow rooms with a window at the end. In this case, the light will allocate the joints, they will become more noticeable, but thereby visually make the room is spacious.

On a note! In case the lamellas are placed perpendicular to the direction of light, their texture will be noticeable much better.

Laminate laying direction scheme in rooms

Also laminate must be focused and depending on the direction of movement on it. Sometimes there are rooms in which you can clearly celebrate the lines along which people living in the house are moving. Most often it is corridors, holles. In this case, in priority during the decision regarding the orientation of the lamellas, there will be no light rays, but the direction of movement - the laminate is laid along these lines. This method will reduce the speed of abrasion of the coating in the joint area, due to which the finish finish of the floor will last longer.

How to lay a laminate - along or across the room

Features of laying laminate in non-standard cases

Sometimes laminate is placed in non-standard rooms in shape and illumination. It is difficult to navigate and decide which direction should "watch" the coating planks. In this case, the situation will save the diagonal laying. The coating is mounted relative to the walls at an angle of 40-60 degrees. In this way. You can not only revive the interior, but also make the joints with littleness.

On a note! This method, although it scolds quite often, is still used in rooms where the windows are located on adjacent walls.

Unfortunately, the method has certain disadvantages. Because of this laying, the abrasibility of the joints increases, and the consumption of the material increases - too much cropping appears.

If the room has the form of the letter "g", then the lamellae is also stacked diagonally or a Christmas tree. So the floor looks quite interesting, the room will not seem narrow.

What to navigate

However, in fact, everything is not so simple. The fact is that the direction of laying laminate will depend on many factors, and not only from light sources. We'll figure it out that it can affect the orientation of the lamellas in the room, and also define, depending on which factors it is worth accepting this or that solution.

First of all, it is important to assess the number and location of windows in the room. If it is one, then there should be no special problems - it is enough to lay the laminate, starting from the far corner of the room, so that the slats are oriented along the direction of light. Thus, it turns out to make the seams with littleness. If there are two windows and more in the room, then you should see, at the expense of which the room is better lit, and orient when installing the coating on it. If there are no windows in the room, and this is quite a frequent phenomenon in corridors, then the laminate orient is recommended depending on the direction of light emanating from the main source - for example, chandeliers.

Tip! It is not bad to immediately estimate the interior of the room, find out where and which furniture will stand. This will allow the overall picture of the finished room and figure out how to lay the laminate so that it looks better.

The shape of the room also matters. If the room is narrow, it is better to discard the desire to hide the seams - here they will be able to play a positive role, visually expanding the room. In particularly complex geometry, the rooms are used by the diagonal installation method, although in this case it is recommended to invite specialists to help, since the newcomer in the world of repairs is unlikely to cope with the task.

It is also important to take into account the location of furniture in the room. If there is a lot of interior items in the room, and there will be carpets on the floor, then it makes no sense to observe the direction of docking lines of laminate.

Important! If the laminate is placed on wooden boards, the lamellas must be laid perpendicular to the floorboards - then the floors will fade less. If wooden floors are closed plywood, then the laminate planks can be plated as more convenient.

Almost every family in his life faces the purchase of housing and decoration of the apartment. One of the most responsible points of repair is the design of gender. Today, laminate acquired great popularity in the building materials market. However, it is not only in the choice of the type of laminated coating, but also the method of its laying. From the direction of laying the laminate, the visual perception of the room and the interior of the room depends.

Preparation of tools and floor surface to laying laminate

In order for the stacking process, it is organized and did not take a long time, you should prepare the necessary tools in advance.

So, for laying panels will be needed:

measuring instruments: Roulette, Construction Level, Cornel;
simple pencil;
electric jigsaw or circular saw;
hammer or rubber cive;
electric drill and drills;
adhesive tape;
substrate;
laminate.

Laminated coating will look good and serve for a long time on the smooth floor. You can check it with a construction level. Daisies are allowed to 2 mm at a distance of 2 m. To eliminate the irregularities of floor alignment, you can use the self-leveling screed. In addition, the surface must be clean and completely dry. After that, it is necessary to place a substrate for a laminate that is hydro, sound and heat insulating.

Back to the category

Laminate laying options

The direction of laying laminate plays a huge role in the design of the floor. With the help of a competent approach, you can visually increase small rooms or, on the contrary, to reduce too huge areas, brighten up unattractive angles, add or shorten the amount of light in the room. In this case, it should be remembered that the drawing of the material and the structure should be approached to the lighting and form of the separated room.

Laying laminate also depends on the methods for fastening the panels among themselves:

Adhesive fastening. The edge of the laminate is applied glue and 2 panels are tightened with each other. In this case, the floor can withstand heavy loads and has increased moisture resistance.
The lock connection "Click" is the most popular method of fastening. The panels are placed by the spike in the groove at an angle of 30 ° to each other and are attached with the castle. At the same time, the seams are almost invisible.
The lock connection "LOCK" works on the principle of locking the locks, in which the spike of one panel is invested in the dadget. At the same time, pieces of laminate must lie in parallel.

straight laying;
diagonal laying
decorative styling: Christmas tree, square, English gleaming.

Back to the category

Straight laying

The most common method is the direct laying of the laminate. An important point is that it is necessary to take into account the angle of light from the window. He should not distinguish the seams on the site of fastening the laminate. With direct laying the boards are located in parallel to each other. If the size of the room is large, then the room is followed along the long wall. The process of direct laying of laminate is very simple: the boards will fall on with smooth rows of each other.

In this case, the long side is located in parallel with the wall, narrow - perpendicularly. The room is visually narrowed. The advantage of this method is the low material consumption - it does not exceed 10%.

You can position the laminate and along the wall of a smaller length. This applies to narrow rooms and corridors. In this case, the space is visually increasing. But if you lay the laminate across the line of light, then the seams between pieces can discard the shadow. In this case, the floor in the room will not look perfectly smooth.

Also direct laying of laminate can be divided into 2 more varieties:

Classic laying scheme. Laminate is starting to sharpen from the window in the direction of light. If the end of the row remains more than 30 cm, they can be used at the beginning of the following. This method is mainly used in apartments and offices.
Brick laying scheme. The method of placing panels is a brickwork. At the same time, each new row begins with a displacement of half the panel from the previous one. Such laying of the laminate ensures the strength of the surface, but the consumption of materials is about 15%.

Laminate laying can be turned from an ordinary classes into artwork. To do this, you have to choose the original drawing by which the planks will be located. But in most cases it is necessary to choose this option to locate the linage joints to visually expand or, on the contrary, reduce the room. To achieve this helps the light falling out of the window. How best to lay laminate in relation to the window? About this, as well as about the choice of laminate for the premises, it will be in the article.

Preparatory work

Successful laminate laying depends largely on how preparatory work will be. They include the preparation of the base, tool and the calculation of the required material. It is for these three steps that goes over the whole time. Each of them will be described in the nuances below.

What should be the foundation

Laying of laminate can only be carried out on a smooth floor or other surface. At the same time, the error is not allowed more than 2 mm on the trafficious meter. In this case, it will not be possible to implement the desired contour. That is why these requirements are presented to the ground:

level resistance;
strength;
minimum humidity.

The preparation of the foundation will depend on which method of laying the laminate was selected. Indoor, where there is a wooden floor, may need minimal intervention. To determine this, you need to carefully inspect the floor for disadvantages. It is important to identify the screens and deficits that occur when walking. It is desirable to assess the status of the lag and the supporting beams on which the plane holds. If a few is required, then it is worth thinking about the preservation of the wooden floor. In the case when extensive intervention is required, it is better to make a complete dismantling. The reason is that the affected tree will be cleaned further.

Damaged lags are withdrawn and eliminated. If mold or fungus appeared under the floor, it is necessary to clean it well and process the affected antiseptic areas. It is important to determine what was the appearance of mold. All the ways to penetrate moisture are needed to overlap, since it will definitely be condensed or seen again. Dranca, which when walking fasten, strengthen. The surface is better to walk the squabble machine so that it becomes perfectly smooth. For the output of the floor to the required level, lining from wood bars are made. After cyclove, wood is covered with an antiseptic composition.

Tip! Check the floor plane drop is the easiest way to use a laser level. The one is best suited that it is capable of projecting a beam with an angle of 360 °. The main points and the tape measure are measured from the beam to the floor plane. The difference in values \u200b\u200band will indicate the difference.

Concrete base sometimes requires longer preparation. The floor must be carefully examined for damage. It is also important to identify hidden flaws. To do this, it can be carefully tired with a hammer. If in some places there is a deaf sound, then over time they can radiate, which will bring unpleasant consequences with them. All potholes are closed with tile glue or other similar solution. After that, you can move to the detection of the surface drop in the method described above.

If the floor drop drop is not more than three centimeters, then it can be compensated using a self-leveling mixture. Before starting work, it is necessary to remove dust and dirt from the floor surface and process it deeply penetrating the primer. If it is quickly absorbed, then the procedure can be repeated twice. After complete drying of the primer, the dry composition of the mixture is purchased. It is divorced with water in the proportions specified by the manufacturer and pours to the marked line. The next step will be the removal of air bubbles from the solution. If this is not done, they can weaken the strength of the entire plane. For the procedure, you will need a needle roller, which must be carried out several times the thickness of the compound solution.

Tip! With a larger floor level drop, you may need to fill a full screed.

Instead of filling the screed, you can apply alignment with plywood or OSB sheets. Before starting work, the surface of the floor is cleaned of garbage and processed by primer. All potholes are closed with glue. The next step will be the laying of the waterproofing film. It should protect wood from swelling and the appearance of mold. The film must be put over a 10 cm overlap between individual sheets, the joints are sampled by scotch. The film also places the adhesive on the wall. The next step is customized and lagged. They are attached to the concrete base with the help of anchor bolts. At the same time, the hats of the bolts must be recessed into the wooden beams, so that there was an opportunity to put the flooring.

All lags must be exhibited by level. After fitting on them, plywood or OSB sheets are stacked. In this case, the material must be chosen such that it does not contain harmful impurities that may be allocated during operation. The sheets of bedding are stacked with displacement of seams to ensure their interlacing. Self-tapping heads should not be outside the leaf, so they need to be drown. From walls to sheets, it is necessary to leave a gap of 5 mm. This gap serves as a thermoshime that compensates for the expansion when the temperature and humidity changes.

Note! Plywood can also be aligned and wooden floor.

Estimated work

After preparatory work before laying the laminate, it is necessary to carry out calculations that will be the key to the rational use of the budget. It is necessary to determine the area that will be littered with laminate. If it is only one room, then it is enough to multiply the width for the length. In the case of several rooms, you will need to calculate the area of \u200b\u200beach and the numbers are summed up. After that, it is necessary to accurately decide on the type and size of the laminate, which will be used for laying. It is important to know the size of one layer of laminate. This will calculate its area. The next step will be calculating the number of required planks. To do this, the total area of \u200b\u200bthe premises is divided into one plank area. Further, the total number of planks is divided into a one that is contained in one package.

After determining the total package, it is necessary to make a stock of 10%. He will help if the laminate planks are spoiled or something will go wrong. After the acquisition of the laminate, it cannot be immediately laid. It is important that the laminate passes acclimatization. This is usually enough one day, but it may be necessary more. During this time, it acquires the temperature and humidity of the room in which it will be mounted.

Tool

Everyone places the laminate using its own tool, if it is a one-time procedure, then there is no need to purchase an expensive power tool and can be done by the following units:

kiyanka;
hook for laying;
roulette;
hacksaw with fine tooth;
spacer pegs;
marking tool.

If the laying is performed constantly, then you can additionally get a tracing saw. It will allow crop laminate at a precisely given angle and with minimal surface damage.

Methods of laying

When buying a laminate, it is important to choose his class correctly. Those that begin with 2 are designed for premises with a small load, so it is better to take 3,3 class, for the bedroom and guests to stay on 31 class for the bedrooms and corridors. Everything will rest in price. The next step will be the choice of the direction of laying laminate relative to the window and the correct implementation of the project.

Selecting direction

The choice of laminate laying direction is due to several factors:

number of windows;
windows location;
room parameters;
laminate design.

If the laminate laying is performed for the first time, then it is better to choose a method of perpendicular to laying to the window. The advantage of this kind of laying of the laminate is that the light from the window falls on the lamellas in parallel with the seams of laminate. This allows you to hide their presence. Thanks to this approach, the floor with laminate seems monolithic. It also allows you to hide some flaws that can be allowed when laying a laminate. At the same time, the boards of laminate look monolithic, which creates a specific charm. If the laminate has embossed, then such a drop of light will emphasize the texture of the laminate board. In this case, this method of laying is better not to use for low-class laminate. The reason is that in the joints of the joint, he grips, which will spoil his appearance.

Note! When choosing this method of laying a laminate, it is worth paying attention to the configuration of the room. If the window is on a larger wall, and at a smaller, then this approach will further extend the room.

The following variant of laying laminate with respect to the window will be the parallel location of the planks. The cause of its choice can be the location of the window in the room, as mentioned above. This method of laying is also chosen in narrow rooms where light falls from the next room. This method of laying the laminate allows a special way to emphasize the texture of the planks. At the same time there is a feeling of an uneven surface. Also, this option is the location of the laminate boards suitable when laying mixed lamellae. Some can be glossy, and other matte.

Tip! For passing rooms, the best way to lay the laminate will be laying according to the direction of movement. Thus, it will be possible to achieve a long service life due to the minimum abrasion of laminate planks on the seams.

If the windows are arranged mixed, then you can lay the laminate diagonally. At the same time, the room acquires elusive lines. The look goes on laminate not up or down, but in the corner of the room. To additionally emphasize the angle, the table or fireplace is placed in it. The angle of laying the laminate in this way is within 40-60 degrees. The diagonal laying of the laminate is considered the most uneconomical, since a lot of waste remains from the laminate planks.

Mounting process

The process of laying requires due attention and skill, which is purchased in the course of work. It is better to start with a long corner of the room and move towards the exit. Most often, laminate laying is conducted from left to right. The prepared surface is covered with lining. If the laying of the laminate is carried out on the concrete floor, then the waterproofing will be required in the form of a film that is stacked according to the sample, as described above. The lining can be made of foamed polyethylene or cork. Between her individual sheets is being made, the joints are punished with scotch. The spike of the first strip of laminate is cut to it easier to accommodate it parallel to the wall.

There is a gap of 5 mm between the wall and the bar. To make it easier to save, plastic pegs are applied. The first row is completely assembled and is located on the place intended for it. If it becomes obvious that the last bar will need to trim more than half, then it makes sense to start not with a whole part, but split the size of the final plank in half and put a short one. The size of the first strip of laminate in the second row should be selected in such a way as to ensure the weave of the seams. After laying each plank, it is necessary to catch a rubber image using a metal bracket. To circumvent pipes and other protrusions, you will need to make a hole with a jigsaw. Video about laying technology can be viewed below.

Summary

As can be seen, the choice of direction of laying of laminate is determined by many factors. As an idea of \u200b\u200bthe designer, the laying drawing can contradict the generally accepted rules. This is required to achieve a certain effect or to match the location of furniture, which will compensate for the size of the room.

Laminate has long won the confidence of consumers, since it is a full-fledged replacement of expensive parquet. This material is used in offices, apartments and country houses. The laminated board has a wonderful appearance, unpretentious in caring and easy to install.

When choosing this coating, the question often arises as laying a laminate along or across. The aesthetic perception of the room will depend on the proper laying. Mounted flooring only on a substrate having a smooth smooth surface.

Align the flooring drops, close the cracks and chips

Before laying a laminate, you need to carefully prepare the surface. If you put it on the plate with a drop in height, the connecting locks will be disperse, and in the process of long-term operation, cracks in the material may occur on an uneven base. The direction of laying laminate does not affect the quality of the flooring, but it matters in the general form of the room.

To prepare the base, we carry out the repair of the plates, close all the cracks and cracks with cement mortar, align the self-leveling mixture or mount a new screed.

The difference is allowed at a height of no more than 2 mm on 2 m surfaces.

Substrates for laminate

After leveling the base, we lay the substrate that performs the functions of the heat-saving and noise insulating material, smoothes small irregularities of the plate and protects against the screens when the boards.

Materials used as a substrate:

Dense polyethylene is used for laying under the laminate of the budget class, has quite good characteristics, simultaneously performs the function of waterproofing, the flares are fitted, the joints are fixed by scotch.
Polyurethane foam rolled material has increased strength, stacked jack, butt stakes with scotch. To enhance thermal insulation, you can use the material with a foil layer.
Bitumen-cork materials are stacked, retain heat well and do not miss the sound.
Corks are used under the highest class laminate, they are durable, combine the best qualities of all the above-described substrates.

The type of material is chosen depending on the functional purpose of the room and the laminate class.

How to lay laminate

Consider how correctly putting the laminate along or across. Most often, the coating is laid along the long wall. Directions of laying laminated board:

across windows;
along the windows;
the diagonal location will help to visually increase the small room, provided that it is not cluttered with furniture.

Styling schemes:

When laying a laminated boards along the light stream (solar or artificial), the coating looks like a solid canvas. If the light drops across the laminate, the locations of the connections become visible.

To visually expand the area of \u200b\u200bnarrow and long room, the laminate is laminated in the transverse direction, perpendicular to the short wall.

Each new row is placed with seam offset, this contributes to a uniform load distribution. For a more economical consumption of material on the last row we use cropped boards. About how you can put a laminate board on the floor, see this video:

The most attractive view has a diagram in which the material is stacked in a checker manner with a shift in each subsequent row of half or one third board.

Montage with your own hands

When they were determined, in which direction to lay the laminate can be started.

After the packaging with the material is listed in the room, they must fly for several days so that the boards adapt to the conditions in which they will be mounted and operated.

Sometimes there is a question, is it possible to lay a laminate from two sides?

The laminate is stacked, it is necessary along or across the room, otherwise it will not work well to docile elements among themselves.

Sequence of laying

Figure laying board

Laying the laminate along or across is performed in the following sequence:

In the walls set wedges to ensure compliance with the compensation space between the wall and the material by 10 mm.
We measure the width of the room and place how many boards will fall in width. If it turns out that on the last row it will be necessary to cut more than half of the board, it is better to cut off the same distance from the laminate of the first and last row so that they look like the same in size.
At the boards, which we will mount in the first row, cut off the comb, so that there is no differential drop in the height. The second row is fastened with a displacement of the board on ½ or 1/3, start with half the board or trim more than 300 mm.
The panels of the last row most often have to dump so that they do in the remaining space. Small irregularities that have arisen on the line of the cut slices will be labeled by plinth.

We connect depending on the type of locks: Click we connect 45 degrees under the tilt and snatch, omitting to the floor, Lock connect in one plane, bearing a rubber hammer. For details, see this video:

The adhesive method is practically not used due to the high cost of glue, the complexity of the work and the inability to disassemble the flooring if necessary.

Making holes for pipes

The hole must be several millimeters larger than the diameter of the pipe

In the room can be heating risers, pipes with hot and cold water. No matter how we decided to lay the laminate along or across the room, you will have to cut a hole under the pipes.

How to cut a hole in the board:

At the end of the installation, close the gap between the pipe and the board of the plug. After laying the laminate in the room you need to install the plinth.

We take out wedges that served as struts, and screw the plinth on the tapping screw or clips to the wall.

Installation sequence:

Cut the plinth in size.
We connect with the elements that are coming in the kit.
We try to the wall if the dimensions match, fix clips on the screws.
Plugs and corner connections to the plinth glit.

When attaching clipses, we make on the wall marking of the clips.

The choice of method and direction of laying depends on the location of windows, premises and the presence of furniture in it. With proper laying, the flooring from the laminated board will serve not one dozen years.