Tools for installing interroom doors. Tools and materials for installing an input metal door What tools are needed to install interroom doors

Installation of doors requires knowledge and experience. Only this is not enough for high-quality installation of the door block. Do not do in this case without special devices.

Even an experienced wizard can not do without special devices for installing doors.

Let's talk about what devices to install doors are needed to any professional or amateur master.

Buying the door of any type:

inlet or interroom;
wooden or metallic;
swing, sliding, harmonica, etc.

Do not forget that in addition to the door canvase there is a box, opening and accessories, which also require the attention of the wizard when installing. There are models of doors, equipped with built-in loops, locks, handles. But it is rarely found, and the model is much more expensive. Then you need to install all components yourself or invite a specialist.

In the arsenal of each man there should be a magical suitcase with devices.

Any professional in his arsenal has a bag with the necessary fixtures for installation. Consider what is included in this bag and for which it is intended to keep the home master to purchase the necessary devices for installing the purchased door.

Overview of doors installation devices

The master requires a different tool for installing the doors, which will be discussed below.

Power tools

Power tools include networking devices and performing all work quickly and neatly. To install any door block, you will need:

Perhaps this is the entire set of power tools. If there are no devices from the list at home, you can buy them for rent. It is better to buy such a tool, because it may be necessary for other houses.

Hand tools and accompanying devices

Many power tools can be replaced with ordinary devices that most often have at home. They will help to install any element, but time and patience will require more:

Screwdrivers of different types help twist any fasteners in pre-prepared holes.
The chisel, the chisel will be suitable for installing a lock or loop. They can carefully hollow out holes, make a recess on the canvas. Just do not hurry so as not to spoil the product with extra actions.
Handheld handmade is required to dipping superfluous from wooden blanks.
Roulette, corner, plumb, level - these devices are also needed to properly produce all measurements and smoothly arrange the door block in the opening or hindow the accessories.
Many masters advise to use device to hold the door leaf in a steady position. When installing the loop or cutting of the castle, you need help with a second person so that the canvas did not fall. Replace the assistant can be a workbench or limiter where the canvas is inserted.

We told about the device to install doors and all components. Take care of the presence of listed items so that the installation passed quickly and successfully.

There were those times when joinery work could be performed using an ax, hammer and chisels. Respecting a company that implements and establishes, uses modern, professional tools.

For high-quality, and sometimes filigree works, it is best to contact specialists who, without nails and self-tapping and self-tapping, will perform all the works of software. Experienced employees of the company DM-Service will qualitatively fulfill the order, using prof. Tools created using the latest technologies. The complex includes installation of fittings, boxes, platbands, sobers (if necessary) and the canvas itself. Professionals use high-quality hand and electric tools. To reduce the risk of damage to expensive materials, door canvases, high-tech equipment is used.

Equipment for inserting door accessories:

handheld electric milling mill (with special snaps), convenient for the cutting of locks of locks, removing the wood layer in the door frame and on the canvas, forming seating places for loops;
the drill is a more convenient and functional tool, for drilling holes of different diameters in the box, if there are feathers in the presence, performs various operations.

For installation and fitting boxes (if necessary, put the good things), platbands:

perforator to increase the openings and installation of anchors (it will not prevent the purchase of 2 tools, heavy and light);
the end saw with the upper horizontal platform, for a flat cut bars and platbands under 45 or 90 degrees, the jigsik and the knife often "cut" the edge, do it not even;
the disk saw is used to reduce the door in height (in the case when the opening is in height below the technological), for cutting a good plank;
screwdriver, with various nozzles makes a significantly easier for tightening screws (in loops, door handles, locks);
electrolzik, we apply in places inaccessible to work saw;
special gun for applying a mounting foam (sealant).

For attaching platbands, many specialists use liquid and finish nails. We use microclemps. They are attached to a reliable, high-quality pneumatic instrument, an industrial class - a pneumaticistole. This installation of platbands is the most popular technology. If the size of the finish nails is 1.5-3 mm, then a microclayer is 0.64 mm. We use them for fastening platbands, staps, lining and fixing a good bar. The microclemp is a reliable, imperceptible mount, without hats of nails and rivets. When used to perform a joinery robot, the door leaf looks monolithic.

Installation is made by laser level - accurate device with an error of 1 mm per meter. The application of the device makes the work better.

Our specialists not only have professional tools, but also the skills of owning them. Buying an interroom door, contact professionals for its installation, so as not to be disappointed by a spoiled product.

The beauty of interior doors can be spoiled by non-professional installation. To install, fasteners of the boxes and decorative elements, did not cause possible dissatisfaction with the result, it is important to choose the instrument correctly.

In the arsenal of masters, there is a large arsenal of devices and means that significantly simplify work and improve their quality. No one will deny that a good tool and competent use is the main condition for the successful installation of interroom doors.

FEATURES OF MONTAGE

Disassembly of the old and installing a new box are accompanied by the formation of a large amount of dust and garbage. To cope with them, you need to prepare devices for cleaning: buckets, broom or brush, rags, mop and vacuum cleaner.

The installation process of interroom structures includes stages of work on which a different tool will be needed. The main stages are:

Disassembly of old interroom doors. If the box remains old, the sash and platbands are removed. The old frame is poured if necessary.
Installation of the box. The box is adjusted under the opening (or vice versa), is collected and fixed in it. The gaps are eliminated by foam and putty.
Decoration of the opening. The protruding sections of the foam are cut, the plaster is drawn by the sandpaper. Disposses are formed and separated. Installed platbands.
The installation of interroom doors is performed. Cut loops, locks. The canvas is hung on the frame. Pens, lining and other fittings are installed.

Everything you need to install interroom doors can be divided into three groups: materials, electric and hand tools.

Consumables

The speed and quality of the installation of interroom doors depends on the quality of the used consumables. Materials are prepared in advance. Purchase better in specialized stores. The following will require the following:

Fasteners You need to buy nails without hats, dowels and screws.

They will be required for mounting the frame, loops, sobers and platbands. All sorts of fasteners should be with a large margin, so they are acquired by boxes.

Mounting foam. It will be necessary to join the slots between the box and the wall. In addition, foam will increase sound and thermal insulation, as well as the adhesion of the box with the wall, therefore, its quality must be guaranteed high.
Putty. The mixture will be needed for sealing and grouting seams and irregularities.

You need to purchase from proven suppliers, since the durability of the protective layer on the stamped areas depends on its quality.

Sherryanka. If the gaps are too broad, without it can not do. It often happens to plaster surfaces with a complex relief. In such cases, the serpent allows you to achieve the necessary strength.
Metal corner. Used when you need to remove smooth corners on the slopes.
Plasterboard. It will be needed to design the planes of slopes.
Wooden wedges. To fix the frame in the opening, you need to have a dozen one and a half small clins. They are made from any wooden rail.
Struts. To keep the frame in the correct position to complete the foam drying, it is necessary to put the struts inside.
Liquid Nails. Fasteners and slopes are often performed using glue.

But that's not all. For the design of the opening will be required:

Capacity for the solution.
Master OK.
Several different sizes of brushes and rollers.
Fixtures for grouting.

Power tools

To install interroom structures, the following set of electrical instruments are used:

Perforator.

Installation of interroom doors without this adaptation is unthinkable. With it, holes are made under the fastener of the block to the wall. The number of fasteners may be different depending on the mass of the design and features of the opening.

Drill. Used to drive holes under fastening screws. Deviles must have a good cartridge that provides high reliability of fixing drill.

Not on time, the drill flying from it can damage the design or damage the masters' health.

Screwdriver. Screwing screws and screws without a screwdriver requires a lot of time and effort. In addition, a high-quality tool allows drilling holes without using a drill.
Electrolzik. The tool will be needed for cutting on platbands.
Bulgarian. If the walls are too curves, their and platbands will need to smoke. For this, the Bulgarian is used.
Mill. The tool is used to cut loops, locks, handles and eyes.
Electrolake. To easily and quickly fit the platbands and good things, you need to have such a tool at hand.
Facial saw. The tool is used to cut bars of boxes and platbands at an angle. It is necessary to have it, but the thing is expensive and at home is rarely used.

Hand tool

Marking, fitting, installation and fasteners of interroom doors need to be performed by preparing the following tool:

Marker or pencil. The latter needs to be chosen as the surface will not scratch. Cutting elements is performed from the front side and if the grooves from the pencil remain on it, the design will lose its appearance.
Roulette. To perform the necessary measurements you need to use a tape measure with a length of 3 meters minimum to reduce the likelihood of errors.

Calipers. To determine the depth of the locking of the lock and perform the markup of the accessories, you need to have such a tool with a depth grader.
Set of chisels. Cutting loops and lining is performed by stoves of different widths.
Building level. A bubble type tool must have a length of at least 50 cm.
Plumb. The exhibition box in the vertical plane needs to be performed with control over the level.
Line. You need to use steel.
Metal square. Checking the correctness of the catch is only necessary with it, and not to the eye.
Stuslo.
Kiyanka, hammer.
Screwdriver Set.
Saw.
Scrap (mount). It will be necessary when removing the old box.
Pistol for foam.

You can familiarize yourself with the tool kit:

What to make a tool for installing interroom structures is understandable. The question in his quality. It is best to work with professional. At worst, it should be high quality manufacturing. He, of course, is expensive, but the pleasure of working with him is more expensive than money. Everything will be disposed of controversy and quickly, and the end result will always be higher.

As a rule, such a tool is not purchased directly during the repair. He must have any man in the farm long before you decide to change or put interior doors. But if you decide to buy it only now, why not? All the same, it will need to be done sooner or later.

Choose and buy the door you like is quite simple, but it is correct to install it - the case is already more complicated. For the competent implementation of this process, you need to have all the necessary tools and devices, and also have some construction skills. Sometimes it may be necessary for special equipment - it is also necessary to have at hand just in case. So, what should be available for high-quality installation of door canvases?

The installation of interroom doors is troublesome and so that it is not enough to prevent one door and pair of screwdrivers. It is desirable to have a whole set of necessary tools to perform this work efficiently.

So, what basic tools are needed to install door cloths:

Drill - Need to drill the necessary holes of different sizes, securing loops, screw the screws;
Perforator - By this useful tool, you can increase or align the door span, drill holes for dowels and perform other necessary actions;
Electropolitanzik - With it, the process of removing platbands and sobers becomes simple and easy (mainly used where it is difficult to use a saw);
Manual mill (plus cutters) - "helps" to prepare spaces under the door loops and the keyboard mechanism, removes the extra layer of wood from the door or door boxes;
Fantasy and circular (disk) saw - such types of saws allow you to do both smooth longitudinal saws of the material and at a certain angle;
Bulgarian - Used to fit the platbands if the walls are very curved;
Screwdriver with nozzles - allows you to fix the screws and other fasteners.

But besides electrical devices and equipment, when installing doors, do not do without hand tools, such as:

Normal hammer - Need to score nails or other details;
Construction knife - It is convenient to cut everything too much;
Chisel - Perfectly suitable for inserting door loops and other fittings;
Screwdriver Set - It will take for fastening various parts;
Building level - the perfect "assistant" to check the surface evenness;
Roulette - Measuring instrument (preferably use three - or five meter tape).

In case there is no screwdriver, in the "instrumental" box, it is desirable to have a crusade and direct screwdriver, which will help consolidate all the necessary elements.

Auxiliary devices for installing interroom doors

During operation with interroom doors, not only the main tool, but also any auxiliary devices, as well as consumables can be needed.

Additional accessories necessary for door mounting:

Bubble level - used to measure the angle of tilt vertical or horizontal surfaces;
Steel line - very convenient for any small measuring work;
Calibration metal square - may be needed when setting up an electric tool, as well as for measuring the angles;
The gun, tired by sealant or mounting foam - is very convenient when applying sealing agents;
Long struts with a width of the doorway;
Pneumoclinia is special wedges that are air pads that can be used as a supporting ballast while working with the door;
Simple pencils or markers - do not pick up these devices with a very hard rod, otherwise the marked marks will be difficult to erase.

In addition to additional tools, you should consider the fact that various consumables will need, without which it is not possible to do work.

What else you need to have at hand:

Chisel and piloes for the perforator;
Drills for a drill;
Milling mills;
Circles for the Bulgarian;
Malyary Scotch;
Mounting foam or sealant;
Self-tapping screws to install the castle, platbands and door loops.

By the way, there are masters who are attached to the finish-free or liquid nails, not using self-tapping screws. You can also try in action special microclemps that are mounted with a pneumatic equipment.

When working with door slopes and plastering, spatulas, brushes or rollers, a solution for a solution, and thicker means may be needed.

Required tool for cutting locks when installing doors

Talking insert locks in the door design, also not to do without special tools. Some of them have already been mentioned above, but about some adaptations it will be for the first time.

So, to embed the lock you will need:

Caliper - this tool is needed to adjust the depth of the insertion of the locking mechanism, as well as apply the markup under the accessories;
Roulette - With it, it is determined by the places where the holes under the castle will be drilled;
Screwdriver or drill - perfectly suitable for fixing the castle elements: handles, latches or lining;
Milling - help prepare holes for the future lock mechanism;
Ring saw - need to make holes for a handle;
Feather drill - without this device, do not do when drinking holes under the lining and latch;
Crown cutter on a tree for a drill;
Ruler, pencil, roulette, screwdriver set;
Chisel and hammer;
Saws.

By the way, there are special sets on sale containing all the necessary equipment to install locks.

Competent and professional installation of doors

It often happens that people doubt their strength and do not risk to take for the installation of doors on their own. In this case, helps professional work. Specially trained people quickly and efficiently install the door, cut the lock, adjust the canvas.

However, if a person has some carpentry skills, you can try to put the doors with your own forces, but for this you need to purchase a high-quality instrument. Now you can purchase professional kits of fixtures for such works.

These sets, as a rule, contain all the necessary fasteners and consumables that may be needed. They also contain a very detailed instruction on which a person who does not even have special knowledge can perform.

The advantages of this set:

Everything you need at hand;
The kit is suitable for any type of door installation;
You do not need to drill the door frame through;
Many elements are fixtures for hidden installation;
Decorative decoration Door neither the droplet will not suffer.

Collect the door yourself or take advantage of the services of a professional - the choice is yours.

Professional tool for installing doors (video)

Selecting the tool first to figure out which work you need to perform. If you want to do everything at the highest level, it is better to buy professional sets. If the work has a one-time work and do not want to spend a lot of money, you can think a little and replace some adaptations easier. All in your hands!

If you have decided to engage in the installation of the interior door on your own, without resorting to the help of specialists, it should be prepared thoroughly. This is especially true for the presence of a tool that will be required to install the door canvase. Installation of interroom doors with your own hands, though not difficult, however, is quite painstaking, and requires the availability of free space and the entire necessary firm tool. Especially if you set asleep, without having professional skills and helpers.

The installation process of the interior door

The immediate installation of the door leaf can be divided into several consecutive steps, each of which requires the use of the required tool to install.

Let us consider in more detail each of the steps, and also we will analyze which tools are needed to install interroom doors on each of them:

Mounting holding door box.
Fastening to the box and canvas of the kit of fittings.
Finish finished doorway.

It is worth noting that for each of the installation stages of the interior door, absolutely different tools can be used, which is why their availability and readiness should be taken care of in advance.

Installation of the door box

The first where the installation of a new door begins, is the box mount step. In this case, you must attend the following tools for installing interroom doors:

Installation of fittings

Once the installation of the box is complete, you can smoothly switch to the preparation of the tool for hanging the accessories and the subsequent installation of the door canvase. In this case, you will need to leave or add the following fixtures for installing interroom doors:

Pencil, roulette, square, line in this case can not be needed.
Drill, drill, screwdriver, saw and a gun for foam - these elements will still be required, so they do not remove them.
Hammer and a set of chisels for additional work.

Installation of the door handle on the interroom door

Depending on the complexity of the accessories, this set can be reduced or additionally add small screwdrivers to it, which may be required when installing the lock. In this case, we will analyze the use of each tool separately.

Pencil and measuring instrument We will need to mark up and accurately measuring the location of future fittings and places for fastening the structure.

The locking of the lock is carried out using a drill and a special drill in the form of a pen, which trifles a uniform neat opening in the doorway.

Drilling hole under the lock in the door

A set of chisels and hammer are used to prepare neat openings under the door loops. In this case, without this tool can not do.

It is worth noting that it is not always at hand there is a whole necessary tool that may be required to drill holes. In this case, the screwdriver can replace drill and screwdriver sets.

Subsequent decoration of the opening

In the process of performing the work of the final stage, namely the attachments of cash, we will need the following tool that you have previously used:

In this case, any special equipment is not used, you can install the interior door with your own hands with you only a few simpler girlfriend tools.

Prepare a solution with a perforator is extremely convenient, since the hand-made mixture requires significant physical exertion. In addition, when using a high-quality tool, you will significantly save time and the more you get a homogeneous mixture that will better fall on the surface of the wall.

Process putty door slope

The solution is applied using a trowel and spatula. With the help of a construction level, it should be estimated and checking how high-quality work performed. After the mixture gets up, you can start staining. To do this, use a brush, crazy and a paint bath.

The last stage of the installation work is fitting and fastening of platbands. Cut them into size can be hand-made with a tree or electric jigsaw with an appropriate saw.