Antigole devices for shoes with their own hands. Hipovka winter shoes at home spikes on sneakers do it yourself

Winter is a pretty attendant period, especially during ice. Despite the fact that utilities sprinkle sand or salt sidewalks, in such periods of pedestrians should be very careful. Slippery soil combined with unsuitable shoes and irresponsibility when moving can provoke a fall and, as a result, injury in the form of an injury, stretching, fracture. To protect yourself with ice, it's just a little neat when walking. It is necessary to select shoes with non-slip soles and additionally use anti-rolling overlays for shoes purchased in the store or made by their own hands.

The least sliding shoes

When choosing winter shoes, it is necessary to pay attention not only to its appearance, convenience, price and brand, but also the quality of the sole. It is necessary to look good, because if it is not intended for walking on ice, the consequences can be dangerous - from discomfort with sock before injury. When buying it is necessary to try out several pairs of shoes, having experienced to feel her clutch with a floor in the store.

It is necessary to stop your gaze on shoes with a corrugated sole. The best option is a protector with a uniform deep relief, directed in different directions. It will provide excellent chaininess with an icy surface. The heel must be wide enough, stable, not too high. It is better if the sole of the shoes will be made of a soft material that does not reflect in the cold: rubber, polypropylene, polyurethane. An excellent option is to buy boots made in those countries that are familiar with cold winter weather.

If you still mistaken when choosing, and the boots were unsuitable for ice walks, you can use anti-slip overlays for shoes purchased in the store or made by your own hands.

Professional lining

There are several types of factory facilities that are attached to the sole and protect against slipping and drops. Anti-slip pads for shoes are released for both for ugg, and for ordinary boots. They are easy to wear and removed. The most common devices that can be purchased at any economic store is:

icewakes - lining on shoes against sliding, which envelop the lower part of the boot, providing the effect of braking on the ice surface;
ice Accommodation - devices similar to icewosters, but additionally equipped with spikes (most often in the area of \u200b\u200bthe sock), which are guaranteed stability;
other devices for ice - anti-slip rubber lining, removable hoops, chains, felt elements.

Such adaptations have some advantages. It:

low price;
wear resistance;
ease of use;
good protection against slipping.

How to choose shoe overlays

If you decide to purchase antifungal overlays on shoes in the store, read the tips on their choice. The main thing is to take with you the shoes on which the devices are bought so that you can try to try. The linings must match the size, do not compress her leg and not be too weakened. Make a few steps to determine whether you feel comfortable in them. From the aesthetic side it is worth picking adaptations to the tone of shoes or with natural metal color.

Carefully inspect the lining that you are going to buy. They should be lighter, so as not to grab the already overall winter boots. It is necessary that their form corresponds to the type of shoes. The material from which anti-slip pads are made on shoes should be durable (best of all steel or polyurethane) and without different defects.

How to make a lining yourself

It is quite simple. To make your own hands anti-rolling overlays for shoes, no effort is required. First, on both sides of the heel, "cheeks" are mounted, made of steel plate. With them, hinges are connected to the covering heel of the bracket, on which in the tubular holes replaceable metal spikes are inserted. They provide grip with a slippery surface. Also on the bracket is a threaded sleeve. Elements are attached to the bracket with welding.

On the heel pad, a metal plate is fixed with the holes located above and below. With the help inserted (in one of them and in the sleeve), the screw, equipped with a head with a knurling, is fixed by a bracket and a plate. When the stack with spikes is in the lower position, the spikes protrude beyond the supporting surface of the heel and perform its anti-skid function. In the upper placement they will be inoperable.

What can be done in the workshop

To make shoes more adapted to the ice, you can contact the workshop. Several options will be offered here.

This material is soft, does not harden on the frost and is well clinging for the ice.
Metal widing. Have excellent clutch and do not allow the sole to slide.
Rubber overlays on shoes against slip. The gasket pasted on the sole will allow stealing to walk on ice.

Folk Methods

There are also folk methods that protect against falls during ice. For example, if the shoes have a smooth sole, it is possible to improve its clutch with the surface - to make corrugated independently with a nail, soldering iron, emery paper or grater. The main thing is not to overdo it in order not to spoil the boots.

In stores selling strips on an adhesive basis. Attaching such anti-slip overlays on shoes, you will protect yourself from ice for several days. Then they should be updated. In addition to sandwich, you can stick a medical plaster or felt on the sole. Another option is improvised spikes from small screws or nails.

An excellent way to make shoes with non-slip - apply the glue "Moment" with anterorant patterns and sprinkle with sand or after drying to be lost with a large sandpaper. You can use another effective method - grate the protectors of the boot of raw potatoes.

Remember that even with properly selected shoes and using different linings when walking on the ice should be extremely neat and careful. It is necessary to look good for your feet, do not make sharp movements, move in small steps.

Last year, wondered - How to make icewinders (icemake) yourself? But still could not come up with a normal fastening for boot. This year I learn inexpensive ready-made solutions that dress on shoes. I ordered a couple of ~ $ 8.

Especially since they did not have the most popular inscription in the world - Made in China or Made in PRC (which is equivalent), and made in Ukraine. After 2 weeks of active wearing steel spikes erased thoroughly And the rubber fastening after drying in the room broke. How do you propose to do?

Do not buy the same low-quality goods for the second time. Score ... but I want run on iceand not move as Granny, constantly fearing to fall.

Solved! I will do CA own ice coats! The design is the same, only here spikes This time will be early. What to choose better?

First wanted to do quite hardcore - with a bunch self-timersBut the poor floors) walk because not only on the street will have to.

Who wants - of course can repeat this option 🙂

The following thought was used bolts with wide washers. But the head will interfere. IN store Methizov An excellent instance for my icewasters With a secret head!

I combined in the test specimen the methods of fastening and the length of the bolt.

The most reliable seems like this: bolt 6-8 mm with a countersunk head + washer + 2-3 layers of rubber (central longest) + washer + washer engraver (that b did not unsubscribed nut) + self-lock nut (for greater reliability).

But not the fact that he is the most optimal.

The gum did, cutting the unnecessary machine chamber. Holes done Personnel for leather.

By the way, with a set of brooks you can get cool pads for household needs.

View from below. We collect ...

Side view.

New homemade and old, torn icewater. Optimal length ice Accessories For an adult leg 385 mm.

Experimental, share your experience with

By purchasing winter shoes, men and women, as a rule, pay attention to the external characteristics - the material, model, on how shoes sits on the leg. Of course, the sole is inspected for practicality and maximum relief convenience. But the non-slip qualities of the base of the boot or boots are paid to the minimum of attention, and in vain - with a strong ice, it is precisely this quality of shoes becomes the most sought-after. But what to do, when it's very much on the street, because not everyone can afford shoes with a special sole? In this article we will tell how to make spikes on shoes with our own hands so that your training has not slipped on ice.

Shoe spike options

In winter, the ice is a frequent phenomenon, so you need to prepare for this time of year. There are so many ways to cope with a gliding on ice.

Important! Many use lining, which are made of sandpaper or lubricate the sole of shoes with a mixture of sand and glue. But these methods are not very practical in solving this issue, although they are also suitable if there is no time for anything else and the ability to create.

The most reliable methods of solving this problem at home are considered:

Use screw screws.
Removable rubber lining.
Acquisition of icewosters in the store.

Icewasters using screw screws

In order to make spikes on shoes with their own hands:

You will need to take screws screws and boots or boots with a fairly thick sole.
Next, you need to spin the screws inside the shoes and carefully fasten them with nuts.

In this case, the length of the screws and the thickness of the shoe is played the most important role.

Important! If you decide to take advantage of this method, then wearing this pair of boots without such protection will already be impossible. Therefore, it is best for this method to choose a pair that will be put on as ice driving.

Icewasters with bulk rubber lining

The process of manufacturing icewosters with removable rubber linings does not take you a lot of time and effort. To make such an ice go:

Take rubber with a thickness of about 5 mm.
Then prepare the sharp tool that you will need in order to later cut the lining them. And most importantly - the spikes that need to be pretty well to fasten into the rubber overlay.

Important! Rubber must choose resistant to temperature differences. It should be well tolerated low temperatures, should not freeze.

When creating a rubber overlay, we should thoroughly think about how this pad will be attached to the base of the boot.

Important! The spikes must have a height of approximately 0.6 mm and should not hang out, and also be comfortable when walking.

The advantages of ice races made by hand

Of course, if you do not want to do this business yourself, you can just buy ice trim in the store. Today in many commercial points there is a large range of a wide variety of models that are made of different materials. But agree, made spikes on shoes with your own hands, have a number of benefits:

Comfortable.
Practical.
Save your money.
Occupy a small amount of time to manufacture.

Stock foot

Icewasters will be able to protect you in bad weather from serious injuries, the risk of which is great on ice. For the winter, try to buy the most comfortable shoes. We wish you in the winter season to move exclusively safely. And making the spikes on the shoes with your own hands, you can more confidently feel during the ice.

In winter, especially after temperature drops, ice is formed on the roads and sidewalks of the streets of our cities. In order to be more resistant to legs in such circumstances, the author came up with how to make overhead spikes for shoes.

Materials and tools that were involved to create this self-catering:
-Tallic plates
-Smoreza
-tyski
-wrench
- How many files
- Dog on metal
- Facts

A detailed description of the manufacture of removable spikes for shoes.

The easiest way is of course screwed into the sole of the screws, but not everyone wants to spoil the shoes in this way. Therefore, the author thought about creating a removable anti-slip system for his shoes.

Step One: The basis for adaptation against slip.

Since the author had pretty suitable furniture attachments in the form of T-shaped plates with already existing holes, it was decided to use them as the main platform to adapt anti-slip.

And yet the plates were too large to use them in this form. Therefore, they were securely clamped in vice and underwent treatment with a metal hacksaw.

Step Two: Processing the workpiece.

A slightly rooting plate is approximately as shown in the photo above, the author began to process the parts obtained using a file.

In addition, side openings were expanded, with a circular file file. Oval forms were attached to the holes, to be more convenient to attach them with ribbons later.

Step Three: Installing self-tapping screws.

After the base in the form of a plate was prepared, it was necessary to attach the screws, which will be warned from slipping. For this, the self-tapping screws were screwed into smaller holes using a conventional wrench.

And to make sure the fastening reliability, the author decided to raise them on both sides.

Step four: Fastening to shoes.

After that, the plate was completely ready, it remains only to take care of the attachment of it to the boot. Special durable tapes with fasteners were used as fasteners, which were trained in advanced plate holes.
In the photos below, you can see the fasteners, suitable on shoes.

As can be seen from the photos, in this case, quite large screws were used, which are more suitable for outside urban use. To use such a device in the city, it is better to either cut part of the length of the screws with a saw, or in advance to use smaller self-sizes in advance.

Late in the fall and winter, holly is common. Not everywhere walking paths sprinkled with sand, therefore, at this time, traumatists rarely sit without work. Slip on ice, and break your hand or leg - it's a simple thing. Share seconds, and ready. To fall with a broken foot for three weeks, and then another month to rub crutches with crutches - the prospect is not at all joyful. Therefore, the people exhibit all the wonders of their ingenuity, so as not to be on the hospital bed! Who buys winter shoes with the spikes already mounted in the sole, who glue the soles special not moving linings, and who is completely trying not to leave the house without at least. I, I can't calmly sit on weekends and holidays at home - I will definitely pass 7-8 km. In the forest, according to specially trotted athletes, the runners, and the same as I walkers, the trail. This route is replete with rather steep descents and lifting.

It is clear that no one in the forest will sprinkle with sand. Because I already have several winters in a row, we have my own shoes with homemade spikes. This is short-lived; On the manufacture of the spikes themselves, as well as on their installation, I leave for about an hour. But then you can not worry about your hands and the legs of the rest of winter and the coming trail in the spring, as long as the snow will not fit. But, as in any case, here, besides numerous advantages, there are also its minuses; Such a hips will well hold on and efficiently work only on a sole of dense, elastic rubber. On the soles of soft and elastic rubber, the spikes will not be kept, as they are not dripping there ... A couple of walks - and there will be no trace from the sizzling. And literally! But the soles of such soft rubber, usually make for summer shoes, for running sneakers, or for playing basketball in the gym, so it's a little chance. And yet, it is better to make sure.

Need

Sheet metal (1 mm thick)
Screws (better black, on wood - they are more chain, 15 mm long.)
Scissors for metal.
Line.
Marker.
Kerner.
A hammer.
Pliers.
Shutter cross.
Drill.
Drill for 4 mm.
Second glue.

Rose shoes

First, it is necessary to clean the shoes and its sole from sand and dust and, while we are engaged in the manufacture of spikes, you can put it on a warm radiator of heating. The spikes we will make a galvanized metal sheet, one millimeter thick.

So, with the help of a ruler and marker, we apply to the metal markup, in the form of the correct cell. The area of \u200b\u200beach square should be 15 × 15 millimeters.

Next, we take Kerner and the hammer, and in the center of each square we will mark for the drill. Drills drills and drill on four millimeters of holes in each square, on a punctured location.

Cut from metal scissors drilled squares.

Here I would advise it better to cut them with a small grinder, with a thin cutting circle, if such tools are available, because the metal is thick for scissors, and I gave yourself all your fingers and palms! After cutting, we take the pliers and bend from each square of the angles into one of the sides. What length is the bending angles, depends on you - how long would you like spikes. The main thing is to fit the screw screw between the curved angles.

Now remove the warm shoes from the heating radiator and screw the finished spikes on the pre-selected treads. There is one fineness - by twisting a screw for three quarters, I still drip down the second glue on the thread, and only then I swear screw into the protector completely.

Just in case. It will not be worse from this.

She finished with spikes. Now we will deal with moisture-repellent composition.

Need

Birch tar.
Solvent.
Some cologne (a few drops, as a fragrance).
Cottage discs or napkins.
Latex gloves.
250 ml bottle.

Impregnation of shoes

Birch vehicle can be purchased in any pharmacy, I caught up in advance, in the summer, in sufficient quantities for such needs. How to drive out of Beresta, I once told, in the master class for the manufacture of a means of mosquitoes. However, now not the season; It is a headache from the birch bark in winter - this is a headache ... So, we diluted in a bottle of birch vehicle with a solvent, the proportions of one to one. Carefully scribble. In a ready-made mixture, inject a syringe about one cube of anyone chosen by you, cologne. Take up once again. We put on the hands of rubber gloves, so as not to get dirty, wet the napkin with a cooked solution and apply it to shoes.

Do not regret the solution! Thanks to the solvent, it will penetrate all the pores of the shoe. Very soon, the solvent will evaporate, and will be able to come inside, and it will protect the material from which shoes are worked out, from moisture. Also do not forget about the seams that the walls of the shoes are fastened with the sole. Seams need to be impregnated 2-3 times, with a break of 30-40 minutes, as this is the most vulnerable place of shoes. Moreover, the impregnation here has double use; In addition to water-repellent properties, it will slow down and the muffling of the filament of the seam and, as a result, wear of the thread and the further decay of shoes and soles. We put the shoes on a warm radiator. The next morning you can safely wear shoes for a walk or work, and any bad weather will be left.

The main thing is to keep your feet in dry, warm and comfort, then the diseases will bypass you. The shoes confidently keeps ice on ice, in a drowning snow, and also does not slide on the smooth tile, due to the fact that the spikes are located on the soles soles - the tires of the center of the sole is calmly reaching the smooth tile and prevents sliding.